CATHODE RAY TOMES

VS Gumshoe

Vs. Gumshoe (set GM5) (Nintendo, 1986) · Document · 4 pages · 9 sections · original scan

Page 1

(Operation Manual)

MDS (MGS)

|. How to install Software ROMs

Each Software ROM is labeled with a Location Number shown on it ( KY Shaded

Portion illustrated below), which indicates the corresponding location on the P.C. Board where it should be installed.

(Label on Software ROM)

“VS.GUMSHOE” contains 6 Software ROMs, and 1 Custom IC, which have location numbers, 1A or 6A, 1B or 6B, 1C or 6C, 1D or 6D, 2A or 8A, 2B or 8B and 2F or 8F. Each ROM and IC must be mounted into the proper IC Socket.

For VS.DUAL SYSTEM (two monitors): If “VS.GUMSHOE” is to be installed in main (left) side of cabinet, then EPROMs and Custom IC should use locations 1A, 1B, 1C, 1D, 2A, 2B and 2F. For sub (right) side, use locations 6A, 6B, 6C, 6D, 8A, 8B and 8F.

For VS.UNISYSTEM (one monitor): “VS.GUMSHOE” EPROMs and Custom IC must use locations 6A, 6B, 6C, 6D, 8A, 8B and 8F (sub side).

H J K L M N PR

| CAUTION:Make sure the Software 1 ROMs and Custom ICs are H inserted properly. J © SW1 corresponds to this program. MAIN (Left side for two monitor game--Not used LMS for one monitor game) co co NdO-10-SGW i ! I t I I i ! ! ' I ' J e@MS

SWe corresponds to this program. SUB (Right side for two monitor game--Also used for one monitor game) ©

ROM and IC Location on P.C. Board

NOTE: “VS.GUMSHOE” requires VS. P.C. Board Memory Boost Modification.
  • See instructions.
NOTE: “VS.GUMSHOE” can be interchanged between left and right side on two

monitor game.

Page 2

2. Points and methods of adjustment

Game Option Settings MDS P.C. Board

MDS-CPU

SW1--MAIN (Left side for two monitor game--Not used for one monitor game)

SW2:--SUB (Right side for two monitor game--Also used for one monitor game) MDS FOR VS.GUMSH

Swicsw2) 2[3jalsle|

COIN/CREDIT

FREE PLAY OFF

ON

OFF

ON

OFF

OFF

ON OFF

ON

OFF

ON

DIFFICULTY EASY 1

HARD 4 OFF

ON

OFF

ON OFF

OFF

ON

ON

NUMBER OF STEVENSON 5 PER GAME 3 OFF

ON

NUMBER OF BULLET 3 PER BALLOON OFF

ON

1 BONUS STEVENSON YES AWARDED AT 50000 OFF

ON

NOTE: “VS.GUMSHOE” requires VS. P.C. Board Memory

Boost Modification — See instructions.

Page 3

CAUTION

The suggested factory settings for VS. Gumshoe’ are listed below. It is recommended that you carefully check the dip switch settings prior to operation. For the VS. DualSystem , the dip switch settings will be on either SW1 or SW2, depending on which side of the p.c. board you install the EPROM's and custom IC. Refer to the operation manual for further instructions. For the VS. UniSystem the EPROM's and the custom IC must be installed in the "sub" side of the p.c. board, and then SW2 is used.

12345678 123945678 LON BORRBRRR|. |RBRRBEB] (GAG —e} MDS-71 Ch [sae J sows | Sw SWE

neeanaa| =

Please refer to the dip switch settings label and the vs.-pax™ Operation

Manual for further information.

Nintendo of America Inc.

Page 4

VS.P.C. BOARD MEMORY BOOST REQUIRED FOR VS.GUMSHOE PAK

INSTRUCTION FOR VS. MEMORY BOOST MODIFICATION:

ENCLOSED IN YOUR VS.GUMSHOE PAK ARE TWO(2) PRE-CUT “JUMPER” WIRES, SOME OF THE NEWER VS. PAKS REQUIRE A MEMORY EXPANSION

MODIFICATION. PERFORM THE MODIFICATION AS PER THE DIAGRAMS

BELOW, AFTER THIS MODIFICATION, THE P.C. BOARD WILL BE COMPA- TIBLE WITH ALL VS.PAKS PAST AND PRESENT.

NOTE:

THE WIRES MAY BE ATTACHED BETTER IF THE SOLDER IS REMOVED

FROM THE PINS AND THE WIRE THEN HOOKED AROUND THE PINS

BEFORE SOLDERING. ALSO, BE SURE TO GET THE WIRES AS TAUT

(o)as POSSIBLE TO PREVENT SNAGGING. (©)

“SUB” SIDE “MAIN” SIDE

6D, PIN 26(SOCKET) TO 5E, PIN 1(74LS04) 1D, PIN 26(SOCKET) TO 4A, PIN 12(74LS32)

MDS P.C. BOARD - SOLDER SIDE