CATHODE RAY TOMES

Punch-Out Operation Manual (CHP1-UP CHP1-UP-US) (Rev1)

Punch-Out!! (Rev B) (Nintendo, 1984) · Manual · 32 pages · 7 sections · original scan

Page 1

OPERATION MANUAL

MODEL NO: CHP1-UP MODEL NO: CHP1-UP-US

Revision 1

Page 2

J Contents

. Location Setup 1

A.Game Inspection --1

B. Game Installation -- 2

  • Voltage Selection-- 3
  • Power On/Off Switch - 4
  • Adjustment of Video Monitor - &

. Option Switch Settings 6 A. Game Price Settings - 7 B. Game Option Settings --r-esceessesseeeeeeeeseeseeeeseeeeeeeeeees 7

. Self-Test and Bookkeeping ------::--srrrerrrrrrtrtrrttttet ttre 8

_ Maintenance and Repair --.:::c:ccceceeeetttieee tie eteeees 9

A.Fuse Replacementfe)
B.Cleaning9
C.Operation Panel -9

D. Video Monitor Removal - E. Game PCB Removal

_ Radio Frequency Interference sic 13

| Wiring and Connection seis riitrtrtrre terete 14

. Name and Location of each part and Parts List --

WARNING

This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accrdance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment, Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

WARNING

Use of non-Nintendo parts or modifications of your Nintendo game circuitry may adversely affect the safety of your game, and may cause injury to your players.

Page 3
  • Location Setup

A. Game Inspection

CHP Display Panel Game Serial Number Label

CHP Front Screen

CHP

Video Monitor

Video Monitor

Game PCB 054 Shield Cover

Power Supply Assembly

Main Fuse Power On/Off Switch 054 Shield Cage

Power Cord

Power Transformer

Fig. | Game Overview

Page 4
WARNING | _oneck before plugging the game in! The game“ PUNCH-OUT//™” is shipped ready for operation, but a last visual check should be made to insure the final touch of quality control. Please check the following to help us insure that your new game was delivered to you in good condition.
  • Check the exterior of the game for shipping damage, dents, chips, or broken parts.
  • Remove the screws on the Rear Door Panel.
  • Unlock and open the Rear Door Panel, as well as the Service Door inspect the interior of the game as follows:
  • Check that Plug-in connectors are firmly connected.
  • Check that Plug-in integrated circuits on the Game PCB are firmly connected in their sockets.
  • Check that all major subassemblies such as the Power Supply, Operation Panel, and Video Monitor are properly mounted.
  • Remove the tie-wrap that holds the coiled Power Cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation.

B. Game Installation

Fig. 2 Installation Requirements

Power : 170 watts Temperature > Oto 38deg.C (32 to 100 deg.F) Humidity : Not over 95% relative Space required: 63(W) x 90 (D)cm (24 3/4 x 35 1/2 in.) Height : 189 cm (74 1/2 in.)

Page 5

(

  • Voltage Selection Before plugging in your game, make sure the Terminal Block of the Power Transformer is correct for your location's line voltage.

Outlet through Isolation Transformer (For Upper Monitor Only) AC 100V Terminal Block 1OOVA US. 90~120V MAX. Europe 200~240V

Power Supply Fuse aim)

3A 125V

Main Fuse US.: 5A 125V ( 90~120V) Europe : 3A 250V (200 ~ 240V)

Power Transfomer PT-1021A Outlet through Isolation Transformer AC 100V 120VA MAX. For Lower Monitor and Fluorescent Lamp

Power On/Off Switch

This game uses one of two types of transformers which are different in appearance but identical in function. The two types can be interchanged.

Fig. 3 Power Supply Assembly, Power Transformer and Voltage Selection

Page 6
  • Power On/Off Switch A Power On/Off Switch is located in the rear of the game at

the bottom center of the cabinet. See Fig. 1.

If the results of the preceding steps are satisfactory, you are ready to plug the game in, and set the Power On/Off Switch to the “On” position.

WARNING

This game MUST be grounded. Failure to do so may result in destruction of electronic components.

Page 7
  • Adjustment of Video Monitor

From To Game PCB _ Video Monitor 6P-600 Video Man PCB Harness Green Gam Red Gan Blue Gain Signal PCB

INVERT OUT NON INVERT OUT

This Signal PCB is only

attached to TPPU-20-00

:Video Monitor [32 Type] 20-EZV (R-C),

V-SIZE

V-HOLOD

H-CENT

BRIGHT

SOUND VOLUME

&~ foo Fuse 4A (Slow Blow)

| o

Video Momtor

ane Main PCB

Fuse 0.34 (Midget Type) O

Fig. 4 Video Monitor

WARNING

Do not touch the inside of the Video Monitor.

It contains many parts supplied with high voltage.

Page 8
  • Option Switch Settings

A pair of Option Toggle Switches are mounted on the Game PCB.

CHP1-CPU PCB

sw2 ao o z =| CM

“ =

ABCD

swi

Fig. 5 Option Toggle Switches

Page 9

A. Game Price Settings

Fig. 6 Game Price Settings

Toggle (SW1) Settings credit/coin B c

1/3 1/2 Ww 2/1 3/1 4/1 5/1 6/1 Freeplay ON OFF OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON ON ON ON ON OFF OFF OFF ON ON OFF ON ON

B. Game Option Setting Ss

Fig. 7 Game Option Settings

Toggle (SW2) Settings ON

JKLMNfe)P

Game Difficulty Easy (0) | OFF | OFF

  • | ON | OFF \ (2) | OFF) ON Hard (3) |ON | ON

Time

Long(0)OFF | OFF
\(1)ON | OFF
  • OFF | ON
Short(3)ON | ON

Attract Music

Silent(0)OFF
With Music(1)ON

Rematch at a discount

No(0)OFF
Yes(1)ON

Self-Test/Game

Game(0)OFF
Self-Test(1)ON
WARNING

All the Option Switch Settings MUST be done with Power Off.

Page 10
  • Self-Test and Bookkeeping
  • Entry There are two ways to enter Self-Test and Bookkeeping.
  • With pressing Service Switch, set the Power On/Off Switch to the “On” position. Hall of Fame RAM is possible to reset.
  • Set the Self-Test Mode with Toggle P (SW2) on the Game PCB. And set the Power On/Off Switch to the “On” position.
  • Self-Test and Bookkeeping are self-explanatory on the Video

Monitor as follows.

RAM TEST Example | gg) NG Fale RAM location on the PCB (CPU PCB)

! ROM TEST | Example oe BL OK =-———__-— Passed

ROM location8kOK
on the PCBBJOK
(CPU PCB)8HNG—+———_——Failed
Page 11
  • Maintenance and Repair

A. Fuse Replacement This game contains 4 fuses. Replace fuses only with the same type as listed below.

Fig 8 Specification of Fuses

  • Main Fuse U.S. : 5A 125V ( 90~120V) Europe : 8A 250V (200~ 240V) See Fig. 1 and 3
  • Power Supply Fuse 3A 125V See Fig. 3
  • Video Monitor Fuse 4A 125V 0.3A 125V See Fig. 4

B. Cleaning The exterior of the game, all metal parts and all plastic part can be cleaned with a nonabrasive cleanser. You should be careful when cleaning the glass or plastic parts. A dry cloth may cause scratches which will result in a foggy appearance.

C. Operation Panel

  • Operation Panel Removal Before repairing or replacing any switches or 4 way Controller on the Operation Panel, unplug the game. Open the Service Door, which are reach througn the opening, and unlock the Clamps, located at each end onthe underside of the Operation Panel.See Fig. 11.
  • Micro-switch Replacement Whenever you replace any micro-switch on the Operation Panel, a switch gap adjustment is needed as shown in Fig. 9. Also, see Fig. 17 for layout of Control Panel Switches.
Page 12

| Switch Button Assy.

\\Micro-switch Gap:0.2~0 5 mm ( 1/128 ~ 5/256 inch) /

Fig. 9 Switch gap adjustment

  • Lubrication for 4 way Controller To maintain the 4 way Controller in good condition, lubricate the pillow balls and 4 way Guide Plate approx. every 3 months.

See Fig. 10.

Lubricate here//

Fig. 10 Lubrication points

Page 13

D. Video Monitor Remova:

  • Front Screen Removal First remove the Operation Panel and then pull the Front Screen toward you. ‘

Aw |t

Operation ~ Panel Ass'y.

Clamp Service Door

Fig. 11 Front Screen and Operation Panel Ass’y. Removal

MW

Page 14
  • Video Monitor Removal If you need to remove the Video Monitor, follow the instructions listed below. But the following procedure should only be performed by an experienced service technician.
WARNING

It is recommended the game be left unplugged for at least one hour before removing the Video Monitor. This will probably discharge the CRT, but extreme caution is still necessary.

  • Make sure game is unplugged !!
  • Open the Rear Door Panel and remove the Front Screen.
  • Unplug all the harnesses and cables from the Video Monitor.
  • Standing at the front opening of the game, remove the four mounting bolts and flat washers. See Fig. 12.
  • Carefully lift the Video Monitor and pull toward you.
WARNING

Use extreme caution and do not touch electrical parts of the yoke area with your hands or with any metal object in your hands.

Remove the four mounting bolts and flat washers

Fig. Video Monitor Removal

Page 15

E. Game PCB Removal

  • Make sure the game is unplugged !!
  • Open the Rear Door Panel.
  • Remove the 56-pin edge connector from the right side of the 054-FCC PCB on the 054 Shield Cover. ‘
  • Pull out 6 Fasteners located on perimeter of the 054 Shield Cover. See Fig 13.
  • Remove the Game PCB from the 054 Shield Cage by carefully sliding it straight out of the wooden PCB retainer.
  • Pull out 2 Fasteners at the center of the 054 Shield Cover. The Game PCB can be removed now. See Fig 13.

Game PCB 054 Shield Cover

Fastener

054-FCC PCB

Fig. 13 Game PCB Removal

WARNING

A reversed connector will damage your PCB! If the connectors don't slip on easily, don’t force them!

  • Radio Frequency Interference (RF1)

In order to protect against the RFI radiated from this equipment, please comply with the following.

  • Do not use non-Nintendo parts!
  • Do not modify your game circuitry !
  • Do not modify the wiring harness and connections !
  • Connect this game only to a grounded 3-wire outlet.
  • After servicing the Game PCB, shut the 054 Shield Cover completely with the Fasteners. See Fig 13.
Page 16

Wiring and Connection |

Fig. 14 Wiring and Connection

[3 TMBLy | ‘MV_GNO

10P70-140 Flat Cable

10P 70 - 140 Flat Cable

i BAK PCB VIDEO PCB cpu PCB @ CHPI-BAK CHP1-VIDEO CHP? -CPU

P3

5OP40-45 Flat Cable

[42 | Down | [43] SOP 40-45 [4411 Blow | Flat Cable fas}. ] i [47]

[49f [50 [KO Blow] [511S Sound] [52 [TM Sound] rl | [sa] GND | [ss{ GND] [ $6] GND | | 5 le] K]

054-FCC PCB

Page 17

Power Transformer PT-1021A (90~120V) — PT-10218(90~120v) or PT-1022A (200~240V), B(200~240V)

Power Supply PP - 10008 FUSE 12P_ OUT 90V=120V 5A Power Cord o909>> 200v-240V3, ae UP 56P Edge Connecting Harness

WARNING This receptacle for use with Upper Monitor only

Fluorescent Lamp 10W

Video Monitor 3P -500 i Game Counter 5 ane Main PCB Harness

orange

Coing Lampp—o~ Harness | a ee

(Remarks) 2P - 370 2P - 860 4P - 800 Mark(R) means Speaker TV Harness Speaker Harness Service Switch ‘that Harness (R) connector yellow yellow color is

Shielding Wire

Shielding Wire Video Monitor

UP4éType ISP Operation Panel Hamess See 15P Speration Panel Hame rane |

Speaker TV Harness Speaker Harness z =

Page 18

ad a n a © oa ze} c © vo © rot < i) w 3) va io) c Q

Page 19

PARTS LIST: CHP1-UP Game Cabinet Assembly Continued

ITEM PART No. DESCRIPTION

1CHPU-13-03Body (Wooden Game Cabinet)
2TKGU-01-29Fluorescent Lamp Ass'’y.
3CHPU-11-19Name Plate Retainer Upper 598L
4CHPU-12-12CHP-US Display Panel (Name Plate)
5CHPU-11-11Name Plate Retainer Lower 598L
6TPPU-20-00Video Monitor [32 Type] 20-EZV (R-C)

or TKGU-20-00 Video Monitor [31 Type] 20-EZV (R-B)

7CHPU-11-10Front Screen Retainer 598L
8CHPU-13-01054 Black Cardboard Bezel Upper
9CHPU-13-02054 Black Cardboard Bezel Lower
10CHPU-12-13CHP-US Front Screen
11CHPU-12-11CHP-US Operation Panel (Panel Only)
12TKGU-01-49Speaker Grill
13TKGU-01-43Speaker
14TKGU-01-31Operation Panel Clamp A (2 Required)
15TMAU-11-20CS Plate 120W
16TKGU-01-33Service Switch (with Button)
17TKGU-01-11Game Counter
18TMAU-14-17Service Door ADD-S2: Order By Currency
19TMAU-14-18Coin Selector: Order By Currency
20TMAU-34-17Lamp BA-9S 6.3V 0.15A
21TMAU-34-16Lamp Socket BA-9S
22TMAU-34-19Micro-switch ADD D2MC-5F1
23TMAU-14-12Door Lock
24TMAU-11-14Cam B31R
25TMAU-14-11Cash Door ADD
26TMAU-11-27Cash Box ADD
Page 20

Rear View of Game Cabinet Fig. 16

Page 21

PARTS LIST: CHP 1-UP Game Cabinet Assembly ITEM PART No. DESCRIPTION

1TKGU-01-61Vent Grill (2 Required)
2CHPU-13-15Rear Door Panel
3TMAU-14-14Lock K6510‘
4TMAU-11-15Cam A
5CHPU-11-18PCB Stopper (2 Required)
6CHPU-22-01CHP1-VIDEO Complete PCB Assembly
7CHPU-21-01CHP1-CPU Complete PCB Assembly
8CHPU-24-01CHP1-BAK Complete PCB Assembly
9CHPU-01-01-11054 Shield Cover
10CHPU-23-01054-FCC Complete PCB Assembly
1CHPU-11-17054 Shield Spacer (2 Required)
12CHPU-23-35Nylatch Fastener (8 Required)
13CHPU-23-34Nylatch Grommet (8 Required)
14CHPU-01-19PCB Support CBSS-12N (10 Required)
15CHPU-01-20PCB Support CBSS-8N (4 Required)
16TKGU-01-08Power Cord: Order By Voltage & Plug Type
17CHPU-88-01PP-1000A Complete Power Supply Assembly
18CHPU-08-01PT-1021A Power Transformer (For 90~120V)
18CHPU-18-01PT-1021B Power Transformer (For 90~120V)
18CHPU-18-02PT-1022B Power Transformer (For 200~240V)
19TKGU-01-30Caster (2 Required)

20 CHPU-01-01-10 054 Shield Cage

21TKGU-01-65Strain Relief Bushing Plate
22TKGU-01-10Strain Relief Bushing
Page 22

Operation Panel Assembly Fig. 17

Page 23

PARTS LIST: CHP1-UP Operation Panel Assembly

ITEM PART No. DESCRIPTION

1DKCU-14-11Complete 4 way Controller Ass’y.
2TKGU-23-514 way Guide Plate‘
3TKGU-23-23E Ring 4
4TKGU-23-21Switch Collar
5TKGU-23-22Lever Spring
6TKGU-23-20Spring Stopper
7TKGU-23-13Micro-switch VL12L (Bent) (4 Required)
8TKGU-23-17Switch Spacer (4 Required)
9TKGU-23-16Bearing Bracket
10TMAU-12-15Lever Plate
1TMAU-12-14Control Knob Plate 28D
12TMAU-12-16Controller Knob Collar 8L
13TMAU-11-18Knob with Shaft 80.5L
14TKGU-23-34Pal Nut (2 Required)
15TKGU-23-26Nut Plate (3 Required)
16TKGU-23-12Switch Button Bracket (2 Required)
17TMAU-34-18Micro-switch VL12L (Straight) (3 Required)
18TMAU-12-18Collar 34 28x 7H (2 Required)
19TMAU-11-19Operation Panel Fastener B 38W
20CHPU-12-17Black Sponge 2x10 590L
21CHPU-12-11CHP-US Operation Panel
22TKGU-23-32Orange Button Ass’y. (2 Required)
23CHPU-11-14Button Stopper
24CHPU-11-15Nut M30 P2
25CHPU-11-16Switch Button Bracket Large
26CHPU-23-33Button ZAP-2A Ass'y.

(Include Al Ring and Rubber Ring)

PARTS LIST: CHP1-UP Wiring Harness

PART No. DESCRIPTION See Fig. 14 CHPU-41-16 UP 56P-054 Edge Connecting Harness TPPU-93-02 2P-400 Audio Harness (400mm) (2 Required) TPPU-93-07 6P-600 Video Harness (600mm) (2 Required) TMAU-41-12 3P-500 Game Counter Harness (500mm) CHPU-41-13 4P-800 Service Switch Harness (800mm) TMAU-41-14 4P-600 WL Coin Harness (600mm) TKGU-13-06 2P Speaker TV Harness [2P-370] (370mm) TKGU-13-17 2P Speaker Harness [2P-860] (860mm) CHPU-41-11 UP 44 Type 15P Operation Panel Harness CHPU-93-12 50P 40-45 Flat Cable (2 Required) CHPU-93-11 10P 70-140 Flat Cable (2 Required)

Page 24

PARTS LIST : CHP |-CPU PCB Assembly Continued No. DESCRIPTION (Reference Designations and Locations) CHPU-21-01 CHP1-CPU Complete PCB Assembly — OO

CHPU-21-11 Z80A Microprocessor (6H) CHPU-21-12 VLM5030 Speech Synthesizer (6M) CHPU-21-13 RP2A03 Microprocessor (4H)

CHPU-21-15 2764 8K-Byte EP-ROM 250ns CHP1-C-4K (4K) CHPU-21-16 2764 8K-Byte EP-ROM 300ns CHP1-C-8H (8H) CHPU-21-17 2764 8K-Byte EP-ROM 300ns CHP1-C-8J (8J) CHPU-21-18 2764 8K-Byte EP-ROM 300ns CHP1-C-8K (8K) CHPU-21-19 2764 8K-Byte EP-ROM 300ns CHP1-C-8L (8L) CHPU-21-20 27128 16K-Byte EP-ROM 300ns CHP1-C-6P (6P) CHPU-21-21 27128 16K-Byte EP-ROM 300ns CHP1-C-8F (8F) CHPU-21-22 HM6116AP-15 2K-Byte RAM 150ns (4L) CHPU-21-23 TC5533P-A 4K-Byte RAM 150ns (8D) CHPU-21-24 HM6264P-15 8K-Byte RAM 150ns (8C) CHPU-21-25 TC5514AP-3 1Kx4-Bit C-MOS RAM 300ns (8M)

CHPU-21-26 74LS00 Quad 2-Input NAND (3B) CHPU-21-27 74LS02 Quad 2-Input NOR (3A) CHPU-21-28 74LS04 Hex Inverters (4B, 3C, 6D, 6E) CHPU-21-29 74LS08 Quad 2-Input AND (5D) CHPU-21-30 74LS14 Hex Schmitt Inverters (1C) CHPU-21-31 74LS74A Dual “D” Flip-Flops (P, CL) (1D, 1F) CHPU-21-32 74LS92 Devide-By-Twelve Counter (5L) CHPU-21-33 74LS109A Dual J-K Flip-Flops (PLE, CL) (5F) CHPU-21-34 74LS138 3 To 8 Decoder (2C, 2D, 7D) CHPU-21-35 74LS139 Dual 2 To 4 Decoders (7E, 8A) CHPU-21-36 74LS161A 4-Bit Binary Counters (2A, 5A, 5B, 6B, 7B) CHPU-21-37 74LS194A 4-Bit Shift Registers (4A) CHPU-21-38 74LS240 Octal Buffers (TS) (1R, 2R, 5R, 6R) CHPU-21-39 74LS245 Octal Bus Transceivers (7F) CHPU-21-40 74LS259 8-Bit Addresable Latches (2B) CHPU-21-41 74LS365 Hex Bus Drivers (5C, 6C, 7C) CHPU-21-42 74LS367 Hex Bus Drivers (6F, 6K, 7K) CHPU-21-43 74LS374 Octal “D” Flip-Flops (1A,6A,7A,2E, 2F,2H,2J,6L) CHPU-21-44 74S04 Hex Inverters (5K) CHPU-21-45 7437 Quad 2-Input NAND Buffers (5H) CHPU-21-46 75471 Dual Peripheral AND Drivers (3S) CHPU-21-47 74HC20 Dual 4-Input NAND (8N) CHPU-21-48 PST518A Low Voltage Detector (3L) CHPU-21-49 LM324 Quad Operational Amplifiers (2N)

CHPU-21-50 2SC1815 Silicon NPN Transistor (Q1~Q3) CHPU-21-108 2SC2235 Silicon NPN Transistor (Q4)

CHPU-21-51 ES1F Diode (D1) CHPU-21-52 1S5277B Diode (D2, D3) CHPU-21-53 182076 Diode (D4~D7)

Page 25

No. DESCRIPTION (Reference Designations and Locations) CHPU-21-54 DAN401 Quad Cathode-Common Diode Array (DA1, DA2, DA3, DA4)

CHPU-21-55330 pf 50V+5% Styrol Capacitor(C36, C41)
CHPU-21-560.01 uf 50V+10% Mylar Capacitor(C34, C39)
CHPU-21-57=0.015 uf 50V+10% Mylar Capacitor. (C35, C40)

CHPU-21-109 68 pf 50V Ceramic-Disc Capacitor (C52, C53)

CHPU-21-58180 pf 50V Ceramic-Disc Capacitor(C30)
CHPU-21-59220 pf 50V Ceramic-Disc Capacitor(C44, C45)

CHPU-21-60 330 pf 50V Ceramic-Disc Capacitor (C2, C46, C47, C51)

CHPU-21-611000 pf 50V Ceramic-Disc Capacitor(C1)
CHPU-21-620.01 uf 50V Ceramic-Disc Capacitor(C80 ~C150)
CHPU-21-630.068 uf 50V Ceramic-Disc Capacitor(C7, C8, C9)
CHPU-21-641 uf 16V Al Electrolytic Radial Cap.(C3,C4,031,C32,C37,C42)
CHPU-21-653.3 uf 16V Al Electrolytic Radial Cap.(C5, C6)
CHPU-21-6610 uf 16V Al Electrolytic Radial Cap.(C33, C38)
CHPU-21-6733 uf 16V Al Electrolytic Axial Cap.(C43)
CHPU-21-68220 uf 16V Al Electrolytic Axial Cap.(C50)
CHPU-21-690 Ohm Shunt Lead(R18, R19)

All discrete R are Carbon Resistors

CHPU-21-7010Ohm 1/4W £5% Resistor(R6)
CHPU-21-7151Ohm 1/4W £5% Resistor(R14, R92)
CHPU-21-72100 Ohm 1/4W+5% Resistor(R32, R33, R36, R37)
CHPU-21-73110 Ohm 1/4W+5% Resistor(R3)
CHPU-21-74180 Ohm 1/4W+5% Resistor(R61, R68)
CHPU-21-75330 Ohm 1/4W+5% Resistor(R30, R31)
CHPU-21-76820 Ohm 1/4W+5% Resistor(R1, R2, R64, R65)
CHPU-21-771KOhm 1/4W £5% Resistor (R9, R62, R69, R80~R86, R88, R90, R91)
CHPU-21-782.4K Ohm 1/4W+5% Resistor(R49)
CHPU-21-793.3K Ohm 1/4W+5% Resistor(R15, R16, R47)
CHPU-21-805.1K Ohm 1/4W+5% Resistor(R4, R7, R8, R17, R87)
CHPU-21-818.2K Ohm 1/4W+5% Resistor(R57)
CHPU-21-8210K Ohm 1/4W+5% Resistor(R43, R51, R55)
CHPU-21-8312K Ohm 1/4W+5% Resistor(R35, R39, R52)
CHPU-21-8520K Ohm 1/4W+5% Resistor(R5, R34, R38)
CHPU-21-8630K Ohm 1/4W+5% Resistor(R48)
CHPU-21-8743K Ohm 1/4W+5% Resistor(R60, R67)
CHPU-21-8875K Ohm 1/4W+£5% Resistor(R44)
CHPU-21-89100K Ohm 1/4W+5% Resistor(R45, R46, R53, R54, R56)

CHPU-21-110 110K Ohm'1/4W+5% Resistor (R59, R66)

CHPU-21-90150K Ohm 1/4W+5% Resistor(R70, R71)
CHPU-21-91200K Ohm 1/4W+£5% Resistor(R10~R13)
CHPU-21-92Hex 5.1K Ohm Series Resistor Array(RM5)
CHPU-21-93Octal 1K Ohm Series Resistor Array(RM1~RM4)
CHPU-21-94Quad 68 Ohm Parallel Resistor Array(RM6~RM9)
CHPU-21-958 MHz Crystal(X1)
CHPU-21-9621.47727 MHz Crystal(X2)
Page 26

No. DESCRIPTION (Reference Designations and Locations)

CHPU-21-974-Station, Single-Throw, DIP Bit Switch(SW1)
CHPU-21-988-Station, Single-Throw, DIP Bit Switch(SW2)

CHPU-21-111 24 Pin DIP IC Socket (S13)

CHPU-21-9928 Pin DIP IC Socket(S5~S12)

CHPU-21-100 40 Pin DIP IC Socket (S1~S4) CHPU-21-101 10 Pin Connector Receptacle (P1, P2) CHPU-21-102 50 Pin Flat Cable Header (P3, P4) CHPU-21-103 Battery Case TYPE33-3 (UM-3x3) CHPU-21-104 Flat Head Screw M2.6x8 CHPU-21-105 Nut Plate M2.6-P30 (2 per assembly) CHPU-21-106 Wire Tie T18L CHPU-21-107 Dry Battery UM-3 ( “AA” Dry Cell) (3 per assembly)

PARTS LIST : CHP1-VIDEO PCB Assembly Continued

No. DESCRIPTION (Reference Designations and Locations) CHPU-22-01 CHP1-VIDEO Complete PCB Assembly

CHPU-22-592564 8K-Byte EP-ROM 450ns CHP1-V-6N(6N)
CHPU-22-602564 8K-Byte EP-ROM 450ns CHP1-V-8N(8N)
CHPU-22-612564 8K-Byte EP-ROM 450ns CHP1-V-6P(6P)

CHPU-22-62 2564 8K-Byte EP-ROM 450ns CHP1-V-8P (8P)

CHPU-22-1927128 16K-Byte EP-ROM 300ns CHP1-V-2R(2R)
CHPU-22-2027128 16K-Byte EP-ROM 300ns CHP1-V-3R(3R)
CHPU-22-2127128 16K-Byte EP-ROM 300ns CHP1-V-4R(4R)
CHPU-22-2227128 16K-Byte EP-ROM 300ns CHP1-V-2T(2T)
CHPU-22-2327128 16K-Byte EP-ROM 300ns CHP1-V-3T(3T)
CHPU-22-2427128 16K-Byte EP-ROM 300ns CHP1-V-4T(4T)
CHPU-22-252764 8K-Byte EP-ROM 300ns CHP1-V-2U(2U)
CHPU-22-262764 8K-Byte EP-ROM 300ns CHP1-V-3U(3U)
CHPU-22-272764 8K-Byte EP-ROM 300ns CHP1-V-4U(4U)

CHPU-22-28 2764 8K-Byte EP-ROM 300ns CHP1-V-2V (2V) CHPU-22-29 2764 8K-Byte EP-ROM 300ns CHP1-V-3V (3V)

CHPU-22-30N82S129N 256x4-Bit Bipolar ROM CHP1-V-2D(2D)
CHPU-22-31HM6116ASP-15 2K-Byte RAM 150ns(8H, 2N)
CHPU-21-2674LS00 Quad 2-Input NAND(1E, 6S, 5L)

CHPU-21-28 74LS04 Hex Inverters (6C, 4D, 4E, 6E, 1J, 6T)

CHPU-22-3274LS10 Tripple 3-Input NAND(6U)
CHPU-22-3374LS11 Tripple 3-Input AND(8D, 6V)
CHPU-22-3474LS20 Dual 4-Input NAND(7V)
CHPU-22-3574LS21 Dual 4-Input AND(1K)

CHPU-21-31 74LS74A Dual “D” Flip-Flops (P, CL) (3D, 6R, 7S, 7T, 7U)

Page 27

No. DESCRIPTION (Reference Designations and Locations)

CHPU-22-3674LS86 Quad 2-Input Exclusive OR(7D, 1H, 5P, 1S)
CHPU-21-3474LS138 3 To 8 Decoder(5B, 5E, 1R)
CHPU-21-3574LS139 Dual 2 To 4 Decoders(5F, 6J)
CHPU-22-3774LS151 8 To 1 Line Data Selector(1U, 1W, 4W)
CHPU-22-3874LS153 Dual 4 To 1 Data Selectors:(5C, 5D)

CHPU-22-39 74LS157 Quad 2 To 1 Line Multiplexers(4P, F, 8F, 6H, 4N, 5N, 7R) CHPU-21-36 74LS161A 4-Bit Binary Counters (2A, 7C, 8C, 6D, 2E, 3E, 7E, 8E, 6F, 3M, 4M, 5M, 8T, 8U)

CHPU-22-4174LS164 8-Bit Shift Registers(5J, 5K, 2L,2M)
CHPU-22-4274LS174 Hex “D” Flip-Flops(3L, 4L)
CHPU-22-4374LS175 Quad “D” Flip-Flops (CL)(2C)
CHPU-22-4474LS244 Octal Buffers & Line Drivers (TS)(3N, 3P, 5H)
CHPU-22-4574LS273 Octal “D” Flip-Flops (CL)(7H, 84, 1N, 1P, 2P)
CHPU-22-4674LS283 4-Bit Full Adder(2K, 3K, 4K)
CHPU-22-4774LS299 8-Bit Shift/Storage Registers(8R, 8S)
CHPU-21-4274LS367 Hex Bus Drivers(2B, 5W)

CHPU-22-48 74LS373 Octal “D” Transparent Latches(3A, 3B, 7B, 8B, 3C)

CHPU-21-4374LS374 Octal “D” Flip-Flops(8V)
CHPU-22-4974LS375 4-Bit Bistable Latches(4A, 5A, 4B, 6B, 4C)
CHPU-22-5074LS377 Octal “D” Flip-Flops(7J, 1T, 1V, 4V)
CHPU-21-4474S04 Hex Inverters(1B)
CHPU-22-5174F04 Hex Inverters(1C)
CHPU-22-5274F74 Dual “D” Flip-Flops (P, CL)(1D, 4H)
CHPU-22-5374F161 4-Bit Binary Counters(1F, 2F, 3F, 4F)
CHPU-22-5474F174 Hex “D” Flip-Flops(2H, 3H)
CHPU-22-5574F283 4-Bit Full Adder(2J, 3d, 4J)
CHPU-21-51ES1F Diode(D1)

CHPU-22-56 100 pf 50V Ceramic-Disc Capacitor (C10, C11, C12, C13)

CHPU-21-58180 pf 50V Ceramic-Disc Capacitor(C1)
CHPU-21-60330 pf 50V Ceramic-Disc Capacitor(C2, C3, C4, C15)
CHPU-21-611000 pf 50V Ceramic-Disc Capacitor(C14)
CHPU-21-620.01 uf 50V Ceramic-Disc Capacitor(C20~C138)
CHPU-21-68220 uf 16V Al Electrolytic Axial Cap.(C5)

All discrete R are Carbon Resistors

CHPU-21-75330 Ohm 1/4W +5% Resistor(R1, R2)
CHPU-21-77.1K Ohm 1/4W +£5% Resistor(R20~R31)
CHPU-21-793.3K Ohm 1/4W +5% Resistor(R3, R4)
CHPU-21-93Octal 1K Ohm Series Resistor Array(RM1)
CHPU-22-5720.160MHz Crystal(X1)
CHPU-22-5816 Pin DIP IC Socket(S21)
CHPU-21-9928 Pin DIP IC Socket(S1~S11, S13~S20)

CHPU-21-101 10 Pin Connector Receptacle (P1, P2) CHPU-21-102 50 Pin Flat Cable Header (P3, P4)

Page 28

PARTS LIST : CHP!1-BAK PCB Assembly Continued

No. DESCRIPTION (Reference Designation and Locations) CHPU-24-01 CHP1-BAK Complete PCB Assembly

CHPU-24-302564 8K-Byte EP-ROM 450ns CHP1-B-4A(4A)
CHPU-24-312564 8K-Byte EP-ROM 450ns CHP1-B-4B(4B)
CHPU-24-322564 8K-Byte EP-ROM 450ns CHP1-B-4C(4C)
CHPU-24-332564 8K-Byte EP-ROM 450ns CHP1-B-4D(4D)
CHPU-24-34N82S131N 512x4-Bit Bipolar ROM CHP1-B-6E(6E)
CHPU-24-16N82S131N 512x4-Bit Bipolar ROM CHP1-B-7E(7E)
CHPU-24-17N82S131N 512x4-Bit Bipolar ROM CHP1-B-8E(8E)
CHPU-24-35N82S131N 512x4-Bit Bipolar ROM CHP1-B-6F(6F)
CHPU-24-36N82S131N 512x4-Bit Bipolar ROM CHP1-B-7F(7F)
CHPU-24-20N82S131N 512x4-Bit Bipolar ROM CHP1-B-8F(8F)
CHPU-22-31HM6116ASP-15 2K-Byte RAM 150ns(3F, 3H, 3J)
CHPU-21-2674LS00 Quad 2-Input NAND(3B, 3C)
CHPU-21-2874LS04 Hex Inverters(3A, 3D)
CHPU-24-2174LS148 8 To 8 Line Priority Encoders(5H)
CHPU-22-3874LS153 Dual 4 To 1 Data Selectors(1A, 2A)
CHPU-22-3974LS157 Quad 2 To 1 Line Multiplexers(5E, 5F, 6J, 6K)

CHPU-21-36 74LS161A 4-Bit Binary Counters (1C, 1D, 2B, 2C, 2D)

CHPU-22-4274LS174 Hex “D” Flip-Flops(5J)
CHPU-22-4474LS244 Octal Buffers & Line Drivers (TS)(3K, 4J. 4K)

CHPU-24-22 74LS257 Quad 2 To 1 Line Multiplexers(1E, 2E, 1F,2F,1H,2H)

CHPU-22-4574LS273 Octal “D” Flip-Flops (CL)(5K)
CHPU-22-4774LS299 8-Bit Shift/Storage Registers(5A, 5B, 5C, 5D)
CHPU-24-2374LS353 Dual 4 To 1 Line Multiplexers(7J5,8J,7K, 8K)

CHPU-21-42 741S367 Hex Bus Drivers (3E, 1J, 2U, 1K, 2K)

CHPU-22-5074LS377 Octal “D” Flip-Flops(4F, 4H)

CHPU-21-50 2SC1815 Silicon NPN Transistor (Q1, Q3, Q5, Q7, QY9, Q11, Q13, Q14) CHPU-24-25 2SA1015 Silicon PNP Transistor (Q2,Q4,Q6,Q8,Q10,Q12)

CHPU-21-51ES1F Diode(D1)
CHPU-21-59220 pf 50V Ceramic-Disc Capacitor(C18)
CHPU-21-620.01 uf 50V Ceramic-Disc Capacitor(C20~C77)
CHPU-21-6733 uf 16V Al Electrolytic Axial Cap.(C2~C4)
CHPU-21-68220 uf 16V Al Electrolytic Axial Cap.(C1)
CHPU-21-690 Ohm Shunt Lead(R60, R61)

All discrete R are Carbon Resistors CHPU-21-71 51 Ohm 1/4W +£5% Resistor (R9, R19, R29, R39, R49, R59, R66, R6Y) CHPU-21-72 100 Ohm 1/4W +5% Resistor (R6, R16, R26, R386, R46, R56, R64, R67) CHPU-24-26 240 Ohm 1/4W +5% Resistor (R4,R14,R24,R34,R44,R54) CHPU-21-75 330 Ohm 1/4W +5% Resistor (R7,R8,R17,R18,R27,R28,R37,R38,R47,R48,R57,R58,R65,R68)

Page 29

No. DESCRIPTION (Reference Designations and Locations) CHPU-24-27 470 Ohm 1/4W +5% Resistor (R3, R5, R13, R15, R23, R25, R33, R35, R43, R45, R53, R55) CHPU-21-77 1K Ohm 1/4W +5% Resistor (R2, R12, R22, R32, R42, R52, RE0~R82, R84, R85) CHPU-24-28 2K Ohm 1/4W +5% Resistor . (R1, R11, R21, R31, R41, R51, R62) CHPU-24-29 7.5K Ohm 1/4W +5% Resistor (R63)

CHPU-22-5816 Pin DIP IC Socket(S5~S10)
CHPU-21-9928 Pin DIP IC Socket(S1~S4)

CHPU-21-101 10 Pin Connector Receptacle (P1, P2) CHPU-21-102 50 Pin Flat Cable Header (P3, P4)

PARTS LIST : O54-FCC PCB Assembly

No. DESCRIPTION (Reference Designations) CHPU-23-01 054-FCC Complete PCB Assembly

CHPU-23-11 252-28-50-168 56P Edge Connector

CHPU-23-12330 pf 50V Ceramic-Disc Capacitor(C1~C30)

CHPU-23-13 Ferrite Beads BL O2RN2-R62 (FC1~FC30)

Page 30

PARTS LIST : PP-1OO0OA Power Supply Assembly Continued

No. DESCRIPTION (Reterence Designations) CHPU-88-01 PP-1000A Complete Power Supply Assembly CHPU-88-02 3D-0163 Complete Power Supply PCB Assembly

CHPU-88-113D-3000 Hybrid IC(IC1)
CHPU-88-12uPC78M24 3-Terminal Regulator(IC2)
CHPU-88-13TL431CLP Adjustable Shunt Regulator(IC3)
CHPU-88-14TLP541G Photo Coupler(PC1)
CHPU-88-15PC614 Photo Coupler(PC2)
CHPU-88-16RB404/S4VB40 Diode(D1)
CHPU-88-17C25P04Q/20CS04M Diode(D12)
CHPU-88-1830DF2 Diode(D11)

CHPU-88-19 1S1835/10DF6 Diode (D6, D7, D10, D14)

CHPU-88-2018954 Diode(D3)
CHPU-88-21RD5. 1EB3 Zener Diode(ZD1)
CHPU-88-225P2M Thyristor(Q1)
CHPU-88-232SC2562 Silicon NPN Transistor(Q2)
CHPU-88-242SC2749 Silicon NPN Transistor(Q3)
CHPU-88-250.01 uf 50V Mylar Capacitor(C6, C9, C27)
CHPU-88-260.1 uf 50V Mylar Capacitor(C13)
CHPU-88-271000 pf 50V Mylar Capacitor(C12)
CHPU-88-280.047 uf 630V Metallezed Film Cap.(C1, C4)
CHPU-88-290.22 uf 250V Metallezed Film Cap.(C10, C28, C29)

CHPU-88-30 2200 pf 2KV Ceramic-Disc Capacitor (C2,C3,011,C15,C18)

CHPU-88-314.7 uf 50V Al Electrolytic Cap.(C7)
CHPU-88-3247 uf 35V Al Electrolytic Cap.(C8, C17)
CHPU-88-33330 uf 200V Al Electrolytic Cap.(C5)
CHPU-88-341000 uf 50V Al Electrolytic Cap.(C16)
CHPU-88-353300 uf 10V Al Electrolytic Cap.(C19~C26)

CHPU-88-36 100 Ohm 1/4W +5% Carbon Resistor (R9,R11,R12,R23,R24)

CHPU-88-37.1KOhm 1/4W 45% Carbon Resistor(R4, R6, R15)
CHPU-88-381.5K Ohm 1/4W +5% Carbon Resistor(R25)
CHPU-88-392.4K Ohm 1/4W +5% Carbon Resistor(R26)
CHPU-88-4010K Ohm 1/4W +5% Carbon Resistor(R7)
CHPU-88-4124K Ohm 1/4W +5% Carbon Resistor(R17)
CHPU-88-4230K Ohm 1/4W +5% Carbon Resistor(R8)
CHPU-88-435.1.Ohm 1/2W 45% Carbon Resistor(R19, R21)
CHPU-88-44100 Ohm 1/2W +5% Carbon Resistor(R5)
CHPU-88-45100K Ohm 1/2W 45% Carbon Resistor(R3, R14)
CHPU-88-465.1.Ohm 5W +5% Cement Resistor(R1)
CHPU-88-47.20Ohm 5W +5% Cement Resistor(R22)
CHPU-88-4830Ohm 5W +5% Cement Resistor(R10)
CHPU-88-49100 Ohm 5W +5% Cement Resistor(R16)
CHPU-88-50510 Ohm 5W +5% Cement Resistor(R20)
CHPU-88-512KOhm Veritical Cermet Trimpot(VR2)
CHPU-88-5250K Ohm Vertical Cermet Trimpot(VR1)
CHPU-88-53EI-40 Type 3D-0163 Switching Transformer(TR)
Page 31

No. DESCRIPTION (Reference Designations) CHPU-88-54 SC2A Choke Coil (L1) CHPU-88-55 SF-C27-00105-01 Choke Coil (L2) CHPU-88-56 3A SB FGMB NR Type Fuse

CHPU-88-57OG751-0062 Fuse Holder(2 per assembly)
CHPU-88-58Heat Sink Clip(3 per assembly)

CHPU-88-59 Thermally Conductive Rubber CHPU-88-60 2-Pin AC Input Connector Receptacle on PCB CHPU-88-61 6-Pin DC Output Connector Receptacle on PCB CHPU-88-62 7-Pin DC Output Connector Receptacle on PCB CHPU-88-65 3D-0163-32 Type Heat Sink

CHPU-88-63 3D-0163-30 Type Metal Frame CHPU-88-64 3D-0163-31 Type Metal Cover CHPU-88-66 3-Pin AC Input Connector Ass'y.on Metal Frame CHPU-88-67 9-Pin DC Output Connector Ass’y.on Metal Frame CHPU-88-68 12-Pin DC Output Connector Ass’y. on Metal Frame

CHPU-88-69Metal PCB Retainer(4 per assembly)
Page 32

©1983 Nintendo of America Inc. Printed in Japan