CATHODE RAY TOMES

Pole Position II TM-255 2nd Printing

Pole Position II (Japan) (Namco, 1983) · Technical Manual · 38 pages · 22 sections · original scan

Page 1

*Pole Position ai ‘osition ll are engineered and designed by

by a qualified technician. The enhancement of any Pole Position II game should. only be performed TM-255, 2nd Printing

Page 2

Pole Position Il

Enhancement Instructions

Page 3

TM-255 Pole Position II

©1983 by Atari, Inc All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permisssion from the publisher.

The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976.

This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.

In addition, the Act provides for payment of statuatory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys' fees and face an imprisonment of up to five years.

Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or Operation Of a copy Of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Printed in the U.S.A. 10M

Page 4

T™-255 Pole Position II

TABLE OF CONTENTS

INtrOduction .ecccsecc cece cece cece cece ene cee secs eeeseeeecceteeecces Enhancement Kit Inventory..... Tools Required for Enhancement.. Enhancement Procedure for the Upright Game...... Replace the Attraction Glass........... Replace the Display Shield........ Remove the Printed-Circuit Boards... Modify the Printed-Circuit Boards. Set the Option Switches........... Install the Printed-Circuit Boards.. Install the Decals....... Install the Self-Test Chart. Perform a Self—Test..........6 Change the Pole Position Schematic Package.......ssseeeeeceeeeee

Enhancement Procedure for the Sit-Down Game..........cceeeeeeeeeeees Replace the Display Shield...........-.-- Remove the Printed-Circuit Boards... Modify the Printed-Circuit Boards. Set the Option Switches............005 Install the Printed-Circuit Boards.. Install the Decals........-..seeeeee Install the Self-Test Chart. Perform a Self-Test........... eee Change the Pole Position Schematic Package... ..sececeeccereseves

Figure Figure Figure Figure Figure Figure Figure Figure Figure WODIAUAWNH LIST OF ILLUSTRATIONS

Parts Affected by Enhancement Procedure........ Attraction Glass and Display Shield Replacement

NAMCO PCB Components Affcted by Enhancement. . Removing ICs (Cut Pin Method)........ Removing IC PinsS.....seeesecseeceseeuce Removing Solder from Plated-Through Holes. Removing Solder from Lead Connection Pads.... Removing an IC from a Socket...........-eeeee Figure 10 Display Shield Replacement—-Sit—Down. .......seseeseeeecees WOOANYYNWH

SS SBIBBBRY

ili

Page 5

TM-255

iv Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Pole Position II

LIST OF TABLES

Enhancement Kit Contents—Upright...........ceeeeeeecceeee Enhancement Kit Contents— Sit—Down. Tools Required for Enhancement. Atari CPU PCB Component Locations......... Ic Socket Locations on the Atari Video PCB Atari Video PCB Component Locations......... Namco CPU PCB Component Locations. IC Socket Locations on the Namco Video PCB.. Namco Video PCB Component Locations......... Factory-Recommended Settings for Play Options.... Factory-Recommended Settings for Price and Play Options

Page 6

T™-255 Pole Position II

INTRODUCTION

Pole Position II, the sensational sequel to Pole Position, offers you a choice of four racetracks! The tracks—-FUJI, TEST, SUZUKA, and SEASIDE--are based on actual international raceways. The following instructions will help you change a Pole Position upright or sit-down game into a Pole Position II game. These modifications include changing the attraction glass (upright), changing the display shield, changing certain printed—circuit board (PCB) components, posting decals, and installing a new self-test chart. Figure 1 shows parts of the cabinet that are affected by these modifications.

SUPPORTING DOCUMENTATION

These instructions are designed to be used with the following documentation:

e ™218 Pole Position Operation, Maintenance, and Service Manual @ sT-255 Pole Position II Self-Test Chart @ cO-218-12 Pole Position II Operator Information e sp-218 Pole Position Schematic Package or @ SP-219 Pole Position Schematic Package

After you have followed the instructions in this document, refer to CO-218-12 for additional information on Game Play, Self-Test, Option Switch Settings, and Schematic Package changes.

Before you start the enhancement procedures, UNPLUG THE GAME.

Page 7

TM-255 Introduction

Right and Left Side Panel Decals Display Shield with Graphics Display Shield with Graphics

Right and Left Right and Lett Side Panel Decals—Rear Side Panel Decals—Front

Attraction Glass and Film

Via W

aS) NOS

ae | L

Instrument Panel Decal Front Panel Decal

Right and Left Control Panel Decals

CPU and Video PCBs Self-Test Chart See Figures 3 and 4 Includes Self-Test Informa- Modify these PCBs with ICs tion and Option Switch inthe Electronics Kit. Settings—Inside the Cabinet,

Figure 1 Parts Affected by Enhancement Procedure

Page 8

TM-255

ENHANCEMENT KIT INVENTORY Introduction

Before you start to modify the game, check the contents of the Pole Position II Enhancement Kit. The kit contents for upright games are listed in Table 1. The kit contents for sit-down games are listed in Table 2. If any item is missing, contact your Atari distributor.

Note that the integrated circuit (IC) components included in the kit are labeled with their respective part numbers.

Table 1 Enhancement Kit Contents—-Upright

Electronics Kit—-Includes the following:

Pole Position II custom integrated

Pole Position II Operator Information Pole Position II Decal Mailer Card

1/4-Inch wide x 1/4-inch thick black foam

Video display shield with graphics Printed-circuit board label AQ41351-01 C

Part No. Quantity Description

A041352-01 1

79-42C16516-Pin socket
79-42C18218-Pin socket
79-42C28728-Pin socket

136014-166--192 27 Integrated circuits 137351-001 1 circuit CO-218-12 1 CO-218-13 1

ST-2551Self-test chart

78-6900404 50 inches tape (coated on 1 side)

037410-01i,Attraction glass
041353-011Left side-panel decal*
041353-021Right side-panel decal*
041354-021Attraction panel film
041355-031Instrument panel decal

041356-01 1 041377-01 2

041530-012Caution label

*The left and right-side panel decals are optional. Use the miler card provided to receive your free decals.

Page 9

TM-255 Introduction

Table 2 Enhancement Kit Contents—Sit-Down A041376-01 C

Part No. Quantity Description

A041352-01 79-42C16 79-42C18 79-42C28 136014-166——192 137351-001

CO-218~12 ST-255 78-6900404

041377-01 041378-01 041378-02 041379-01 041379-02 041380-04 041380-05 041381-01 041382-01 041530-01 BPyvynure

24 inches

NER PREPPED Electronics Kit—-Includes the following: 16-Pin socket 18-Pin socket 28-Pin socket Integrated circuits Pole Position II custom integrated circuit Pole Position II Operator Information Self-test chart 1/4-Inch wide x 1/4-Inch thick black foam tape (coated on 1 side) Printed-circuit board label Left side-panel decal (rear) Right side-panel decal (rear) Left side-panel decal (front) Right side-~panel decal (front) Left control panel decal Right control panel decal Video display shield with graphics Front panel decal

Caution label
Page 10

T™-255

Tools Required for Enhancement Introduction

The tools listed in Table 3 (or their equivalents) are required to complete this modification.

Table 3 Tools Required for Enhancement

Quantity Description Purpose

11/8-inch Allen wrenchInstall attraction glass
1Diagonal cuttersRemove PCB components
1Needle-nose pliersInstall PCB components
1Solder suckerRemove solder from PCB
1Solder wickRemove excess solder from leads
1Isopropyl alcoholClean flux and debris from PCB
1Acid brushClean flux and debris from PCB
1Phillips-head screwdriverRemove access panel and PCB
115 to 27 W soldering ironInstall PCB components

masking tape Squeegee stapler

NOTE Install decals Install decals Install self-test chart

Modification instructions for the upright cabinet begin on page 7; modification instructions for the sit-down cabinet begin on page 27.

Page 11

TM-255 Upright Cabinet

Top Retainer

Attraction Glass

Display Shield Retainer

Display Shield

Figure 2 Attraction Glass and Display Shield Replacement

Page 12

T™-255 Upright Cabinet

ENHANCEMENT PROCEDURE FOR THE UPRIGHT GAME

These procedures must be performed by qualified service personnel. UNPLUG THE GAME before starting the following procedures.

REPLACE THE ATTRACTION GLASS

This procedure is illustrated in Figure 2.

1. Use the 1/8-inch Allen wrench to remove the three screws and washers that fasten the top retainer to the cabinet. Remove the retainer. Save the retainer, washers, and screws for reassembly.

Loosen the three screws that fasten the bottom retainer to the cabinet.

Remove and discard the attraction glass. If there is a film behind it, remove and discard the film also.

Take the attraction glass, attraction film, and foam tape out of the enhancement kit. Place a strip of foam tape lengthwise along the top and bottom of the attraction glass.The tape on the glass should be toward you.

Put the attraction film behind the attraction glass. You should be able to read the film. Place the attraction glass and film in the bottom retainer.

Tighten the screws in the bottom retainer.

Reinstall the top retainer, using the washers and screws you saved in step l.

REPLACE THE DISPLAY SHIELD

This procedure is also illustrated in Figure 2.

  • Use the 1/8-inch Allen wrench to remove the screws and washers that hold the display shield retainer in place. Save this hardware for reassembly.
  • Lift the display shield out of the cabinet.

3. Install the display shield contained in the enhancement kit.

Page 13

T™™-255, Upright Cabinet

  • Reinstall the display shield retainer with the hardware you saved in step 1.

REMOVE THE PRINTED-CIRCUIT BOARDS

See T-218 (Figures 1-1 and 1-2) for the location of the Central Processing Unit (CPU) printed-circuit boards (PCB) and the Video PCB.

NOTE

If your game was built in the United States of America, the CPU and Video printed-circuit boards are attached to an Electromagnetic Interference (EML) Shield printed-circuit board. If your game was built in Ireland, it will NOT have the EMI Shield printed-circuit board.

  • Open the access panel at the rear of the game.
  • Disconnect the two edge-connectors from the game PCB set. If your game has an EMI Shield PCB:

a. Disconnect the two edge-connectors from the EMI Shield PCB.

b. Pull the eight snap-in fasteners on the EMI Shield PCB to the unlocked position.

Be careful not to twist the printed-circuit boards as you remove them! If you do, components or connections may be loosened.

  • Carefully slide the PCB set straight out of its guides.
  • Carefully remove the EMI Shield PCB from the Video and CPU boards.
  • Put the printed-circuit boards on a clean work surface.
Page 14

TM-255 Upright Cabinet

MODIFY THE PRINTED-CIRCUIT BOARDS

To avoid damage to the printed-circuit boards, remove them from the game before you attempt any modifications. Refer to “Remove the Printed-Circuit Boards" procedure given previously. Also, perform modifications only with the printed-circuit boards on a clean work surface.

To determine whether your printed-circuit board (PCB) set was designed by Atari or Namco, compare the PCB outlines with those shown in Figures 3 and

  • If you are modifying an Atari PCB set as shown in Figure 3, perform the procedure "Modifying the Atari PCB Set.” If you are modifying a Namco PCB set as shown in Figure 4, perform the procedure "Modifying the Namco PCB Set."

Before modifying the printed-circuit boards, read "Soldering Precautions."

Page 15

TM-255 Upright Cabinet

2 5 r ArAc Tam. oO DF

VIDEO PCB CPU PCB

Figure 3 Atari PCB Components Affected by Enhancement

Page 16

TM-255 Upright Cabinet

=.

CPU PCB VIDEO PCB

Figure 4 Namco PCB Components Affected by Enhancement

ll

Page 17

T™-255 Upright Cabinet

Soldering Precautions

Soldering Techniques Observe the following recommendations when removing or installing components soldered to a PCB in this game. Poor soldering practices can damage a PCB or heat~sensitive electrical components.

Choosing the proper soldering iron is essential before attempting to remove or install soldered-in components. Excessive heat is a common cause of damage to a component or PCB. However, transient voltages from solder guns or improperly grounded soldering irons can also damage certain voltage-sensitive semiconductor devices.

A 15- to 27-watt pencil-tip soldering iron is recommended to avoid separating the etched circuit wiring from the board material and to avoid damaging active components. A temperature-controlled soldering station rated at 700°F with a fine cone or a very fine chisel tip can also be used.

Solder guns are not recommended for removing or replacing soldered-in components on a printed-circuit board. The added possibility for overheating and the large transient voltages induced by the solder gun could cause damage to heat- or voltage-sensitive devices.

The following additional equipment is recommended for removing and installing soldered-in components:

@ Solder Sucker--Hand-operated vacuum tool used to remove liquified solder from the PCB. Top-of-the-line Soldapullt® brand is recommended .

@ Solder Wick--Resin-soaked copper braid used for removing excess solder from the lead connections on the PCB. See "Removing Integrated Circuits" for precautions relating to the use of a solder wick on a PCB with plated-through holes.

e@ Flux Remover—-Non-corrosive chemical used to clean foreign material from the PCB before soldering. Also used to remove any flux residue where components have been installed and to clean any foreign material from the PCB during preventive maintenance. Isopropyl alcohol is recommended.

Page 18

TM-255 Upright Cabinet

® Acid Brush--Small stiff-bristled paint or tooth brush used with flux remover to clean flux and other foreign material from the PCB.

Removing Integrated Circuits The easiest and safest method for removing soldered-in integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke or diagonal cutter as shown in Figure 5.

Use the proper soldering iron as described under "Soldering Techniques." Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each pin in a random order. Remove the loosened pin with the tip of the soldering iron or a needle-nose pliers as shown in Figure 6. Allow a moment for the PCB to cool before proceeding to the next pin. Apply just enough heat to remove any stubborn pins.

Do not use a solder wick to remove solder from inside plated-through holes. The heat required for the solder wick to remove the solder from inside the hole could damage the PCB.

For a PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 7 . (If possible, suck the solder from the opposite side of the PCB from where the heat is applied.)

Do not use a solder wick to remove solder from inside plated-through holes. The heat required for the solder wick to remove the solder from inside the hole could damage the PCB.

Page 19

TM-255

Diagonal Cutter

Figure 5 Removing ICs (Cut Pin Method)

Soldering Iron

Solder Sucker

Preferred Method Upright Cabinet

Needle-Nose Pliers

1% <

Soldering Iron 4

Figure6 Removing IC Pins

Solder Sucker

Soldering Iron

Alternate Method

Figure 7 Removing Solder from Plated-Through Holes

Soldering Iron Solder Wick

Figure 8 Removing Solder from Lead Connection Pads

Page 20

M255 Upright Cabinet

Use a solder wick to remove excess solder from around the lead connection pads on the top or bottom surface of the PCB as shown in Figure 8.

Modifying the Atari PCB Set

Modifications to the Atari PCB set include replacing and addding integrated circuits and sockets to both the CPU PCB and the Video PCB. Be sure to observe the precautions given previously under "Soldering Precautions." +e

On the CPU PCB:

  • Using the method shown in Figure 9, remove the integrated circuits at locations 3E, 3L, 4B, 4L, 7F, 7H, 12E, and 12F from their sockets.
NOTE

The more recently produced Pole Position boards were manufactured to accommodate the parts in this enhancement kit. Therefore, your game CPU PCB may already have IC sockets at locations 3D, 4D, and 4K. If so, omit steps 2 and 3 and continue with step 4.

  • Using the proper soldering techniques, remove the solder from the plated-through holes at locations 3D, 4D, and 4K.
  • Remove three 28-contact IC sockets from the enhancement kit and install them on the PCB at locations 3D, 4D, and 4K. Be sure to observe the proper placement of the socket index as shown on the PCB.
  • Using the information given in Table 4, remove each specified IC from the enhancement kit and install it in the proper socket.
Page 21

T™-255 Upright Cabinet

  • Insert screwdriver tip under body of IC.
  • Gently pry IC upward.
  • Insert screwdriver tip under other side of body and gently pry upward.
  • LiftIC out of socket.

Figure 9 Removing ICs from a Socket

Page 22

TM-255 Upright Cabinet

Table 4 Atari CPU PCB Component Locations

IC Part No. CPU_PCB Location

136014-176 3L 136014-177 4L 136014-178 3E 136014-179 4E

136014-180 7H 136014-181 12F 136014~182 12E 136014-183 7F 136014-184 3D 136014-185 4D 137351-001 aK

1. On the Video PCB:

Using the method shown in Figure 9, remove the integrated circuits at locations 6N, 7N, 12K, 12L, 13K, 13L, and 13N from their sockets.

Using the method given under "Removing Integrated Circuits," remove the soldered-in IC at locations 4L, 5K, 8M, 11C, 11D, 11E, and 12H.

Remove the 24-contact IC sockets from the PCB at locations 6N and 7N.

Using the information given in Table 5, remove the appropriate IC sockets from the enhancement kit and install each in the specified location.

Page 23

TM-255 Upright Cabinet

Table 5 IC Socket Locations on the Atari Video PCB

No. of Contacts Install at Location:

16 5K 16 8M 16 lic 16 11D

16 llE 18 4L 18 12H 28 6N

28 7N 28 12M 28 13M

  • Using the information given in Table 6, remove each specified IC from the enhancement kit and install it in the proper socket.

Table 6 Atari Video PCB Component Locations

IC Part No. Video PCB Location

136014-166 13K 136014-167 12K 136014-168 13L 136014-169 12L

136014-170 13N 136014-171 12N 136014-172 7N 136014-173 6N

136014-174 12M 136014-175 13M 136014-186 llE 136024-187 11D

136014-188 lic 136014-189 8M 136014-190 5K 136014-191 4L 136014-192 12H

Page 24

TM-255 Upright Cabinet

Modifying the Namco PCB Set

Modifications to the Namco PCB set include replacing and adding integrated circuits and sockets to both the CPU PCB and the Video PCB. Be sure to observe the precautions given previously under "Soldering Precautions."

On the CPU PCB:

  • Using the method shown in Figure 9, remove the integrated circuits at locations 4M, 8M, 4L, 8L, 5H, 6H, 5A, and 6A from their sockets.
NOTE

The more recently produced Pole Position boards were manufactured to accommodate the parts in this enhancement kit. Therefore, your game CPU PCB may already have IC sockets at locations 3L, 3M, and 7L. If so, omit steps 2 and 3 and continue with step 4.

  • Using the proper soldering techniques, remove the solder from the plated-through holes at locations 3M, 3L, and 7L.
  • Remove three 28-contact IC sockets from the enhancement kit and install them on the PCB at locations 3M, 3L, and 4L. Be sure to Observe the proper placement of the socket index as shown on the PCB.
  • Using the information given in Table 7, remove each specified IC from the enhancement kit and install it in the proper socket.

Table 7 Namco CPU PCB Component Locations

IC Part No. CPU PCB Location

136014-176 8M 136014-177 8L 136014-178 4M 136014-179 4u

136014-180 6H 136014-181 6A 136014-182 SA 136014-183 5H

136014-184 3M 136014-185 3L 137351-001 7L

Page 25

™-255 Upright Cabinet

On the Video PCB:

No. of 1. Using the method shown in Figure 9, remove the integrated circuits at locations 1E, 1F, 4M, 3M, 1M, 4N, 3N, and 1N from their sockets.

  • Using the method given under "Removing Integrated Circuits," remove the soldered-in IC at locations 3C, 4D, 2H, 10L, 9L, 8L, 6M, and 2N.
  • Remove the 24-contact IC sockets from the PCB at locations 1E and iF.
  • Using the information given in Table 8, remove the appropriate IC sockets from the enhancement kit and install each in the specified location.

Table 8 IC Socket Locations on the Namco Video PCB

Contacts Install at Location:

16 2H 16 8L 16 oL 16 10L

16 4D 18 6M 18 8c 28 1E

28 iF 28 2M 28 2N

Page 26

TM-255 Upright Cabinet

  • Using information given in Table 9, remove each specified IC from ‘he enhancement kit and install it in the proper socket.

Table 9 Namco Video PCB Component Locations

IC Part No. Video PCB Locations

136014-166 4N 136014-167 4M 136014-168 3N 136014-169 3M 136014-170 1N 136014-171 1M 136014-172 iF 136014-173 1E 136014-174 2M 136014-175 2N 136014-186 8L 136014-187 OL, 136014-188 10L 136014-189 2H 136014-190 4D 136014-191 3c 136014-192 6M

Page 27

TM-255 Upright Cabinet

SET THE OPTION SWITCHES

NOTE

The manufacturer tested Pole Position II upright games and found that in an arcade environment, upright games have excellent earnings with switches set to sit-down game settings.

If you have an Atari PCB, the switch which controls game play options is located at 9L. (It is located at 9E if you have Namco PCBs.) We recommend that the game be set for 120 seconds preliminary game time, that the preliminary rank and extended rank levels are set to "B" (moderate difficulty), that the game is set for 5 laps per game, and that the game is played at high speed. To select these options, set the toggle switches as listed in Table 10.

If you have an Atari PCB, the switch which controls game price options and special play options is located at 9J. (It is located at 7E if you have Namco PCBs.) We recommend that the game be set for 50 cents per game, that the unit of speed is miles per hour, that the sound is on in the attract mode, and that the screen displays normal action (not frozen!) To select these options, set the toggle switches as listed in Table 11.

Please refer to CO-218-12 for more information about game options.

Table 10 Factory-Recommended Switch Settings for Play Options

Toggle Switches at 9L or 9E

Cabinet12345678
Sit~DownOnOffOffOffOffOffOnOn

Upright Off Off Off Off Off Off Off On

Table 11 Factory-Recommended Switch Settings for Price and Play Options

Toggle Switches at 9J or 7E

Cabinet12345678
Sit-DownOnOnoffOnOffOnOffOff
UprightOffOffOffoffOffOnoffoff
Page 28

TM-255 Upright Cabinet

INSTALL THE PRINTED-CIRCUIT BOARDS

NOTE

Two labels are included with your kit. After you have finished modifying the printedcircuit boards, peel each Pole Position IL label off its protective backing and place it by the cable connector of each PCB as shown in Figure 3 or 4.

  • Make sure the foam pad is secure between the Printed-circuit boards of the game set. Carefully slide the modified PCB set into the mounting guides.
  • Connect the edge-connectors to the game printed-circuit boards. Make sure these are firm connections. If your game has an EMI Shield PCB:

a. Push the eight snap-in fasteners on the EMI Shield PCB to the locked position.

yb. Connect the two edge-connectors to the EMI Shield PCB.

  • Close the access pane] at the rear of the game.

INSTALL THE DECALS

The following decal installation procedure should be performed by two people. (One person may have difficulty handling the cabinet and the large decals.)

Three decals on the upright cabinet need to be attached--the left side panel decal, the right side panel decal, and the instrument panel decal (see Figure 1).

Page 29

TM-255

wo

10.

ll. Upright Cabinet

Adhesive is contained in small glass beads that are spread on the back of each decal. Pressure applied to these beads will cause them to break, and the decal will adhere immediately! Therefore, do not apply ANY pressure to the decal until it is exactly in the desired position.

Mix a normal dishwashing solution of water and any liquid dishwashing detergent in a shallow pan.

GENTLY lay the cabinet on its left side on a soft blanket.

Thoroughly clean the side of the game cabinet to ensure the removal of all dust.

Use a sponge to liberally apply the water and detergent solution over the entire side of the game cabinet.

Carefully place the right side panel decal, sticky side down,in the center of the wet surface of the game cabinet. Position the decal within 1/4-inch of the edges of the right side panel. Handle only the edges of the decal, and do not press any part of the decal. Use masking tape to position the edges of the decal exactly where they should be.

Use a squeegee to remove all the excess water and detergent from beneath it by quickly working from the center to the outside edges.

When the wrinkles are removed and the decal is free of all excess water and detergent solution, carefully upright the cabinet. Then GENTLY lay the cabinet on its other side on a soft blanket.

Repeat steps 2 through 7 for the remaining left side decal.

Carefully upright the cabinet. GENTLY place the instrument panel decal directly over the instrument panel.

Press the decal firmly and smoothly from the center to the outside edges of the decal.

Use a lint-free cloth to wipe off any excess water and detergent from inside and outside of the cabinet. Allow time to dry before proceeding.

Page 30

T™-255 Upright Cabinet

INSTALL THE SELF-TEST CHART

  • Open the access panel at the rear of the game.
  • Remove and discard the self-test chart that is in place.
  • Staple the Pole Position II Self-Test Chart, ST-255, into place. (This chart contains important information about game settings.)
  • Close the access panel at the rear of the game.

PERFORM A SELF-TEST

CHANGE

NOTE

Perform the self-test after the enhancement modifications are completed!

  • Plug the game in.
  • Set the power on/off switch to the on position.
  • Perform the self-test procedure as described in CO-218-12 (Pole Position II Operator Information).

THE POLE POSITION SCHEMATIC PACKAGE

The Pole Position Schematic Package Supplement, SP-218, supports games with the Atari PCB set. The Pole Position Schematic Package Supplement, SP-219, supports games with the Namco PCB set. Refer to 0-218-12 (Pole Position II Operator Information) for changes to these schematic packages. Mark these changes into your schematic package!

After you have changed the schematic package, the enhancement procedure for the Upright cabinet is complete.

Page 31

TM-255 Sit-Down Cabinet

Display Shield

Figure 10 Display Shield Replacement—Sit-Down

Page 32

TM-255 Sit-Down Cabinet

ENHANCEMENT PROCEDURE FOR THE SIT-DOWN GAME

These procedures must be performed by qualified service personnel. UNPLUG THE GAME before starting the following procedures.

REPLACE THE DISPLAY SHIELD

This procedure is illustrated in Figure 10.

1.

2. Have someone hold the control panel firmly against the cabinet while you are removing the wing nuts from the rear of the game. This prevents the top-heavy assembly from crashing against the cabinet.

Open the access panel at the rear of the game.

Reach toward the front of the game, and remove the wing nuts and washers that secure the control panel to the game cabinet. (Someone should hold the control panel against the cabinet as you do this!) Save this hardware for reassembly later.

Pull the bottom of the display shield toward you. Remove and discard this shield.

Apply a strip of foam tape to the front bottom of the display shield provided in the enhancement kit.

Insert the Pole Position II display shield. Close the control panel. Someone should hold the control panel against the cabinet as you reinstall the hardware.

From behind the cabinet, reinstall the wing nuts and washers you saved in step 1.

Page 33

TM-255 Sit-Down Cabinet

REMOVE THE PRINTED-CIRCUIT BOARDS

See TM-218, Figure 1-2, for the location of the game printed-circuit boards in the sit-down cabinet.

NOTE

If your game was built in the United States of America, the CPU and Video printed-circuit boards are attached to an Electromagnetic Interference (EMI) Shield printed-circuit board. If your game was built in Ireland, it will not have the EMI Shield printed-circuit board.

  • Open the door at the rear of the game. The printed-circuit boards are mounted on the door.
  • Disconnect the two edge-connectors from the game PCB set. If your game has an EMI Shield PCB:

a. Disconnect the two edge-connectors from the EMI Shield PCB.

b. Pull the eight snap-in fasteners on the EMI Shield PCB to the unlocked position.

Be careful not to twist the Printed-Circuit Boards as you remove them! If you do, components or connections may be loosened.

  • Carefully slide the PCB set straight out of the guides.

MODIFY THE GAME PCB

This procedure is the same as the procedure for the upright cabinet.

SET THE OPTION SWITCHES

After your PCB set has been modified, refer to "Set the Option Switches" on page 22 of this manual for information on setting the option switches.

Page 34

TM-255 Sit-Down Cabinet

INSTALL THE PRINTED-CIRCUIT BOARDS

NOTE

Two labels are included with your kit. After you have finished modifying the printedcircuit boards, peel each Pole Position II label off its protective backing and place it by the cable connector of each PCB as shown in Figure 3 or 4.

  • Make sure the foam pad is secure between the printed-circuit boards of the game set. Carefully slide the modified PCB set into the mounting guides.
  • Connect the edge-connectors to the game printed-circuit boards. Make sure these are firm connections. If your game has an EMI Shield PCB:

a. Push the eight snap-in fasteners on the EMI Shield PCB to the locked position.

b. Connect the two edge-connectors to the EMI Shield PCB.

  • Close the door at the rear of the game.

Install the Decals

CAUTION The following decal installation procedure should be performed by two people. One person may have difficulty handling the cabinet and the large decals.

Seven decals on the sit-down cabinet need to be replaced——-two left side panel decals, two right side panel decals, two control panel decals, and the front panel decal (see Figure 1).

Page 35

TM-255 Sit-Down Cabinet

A— avrion

Adhesive is contained in small glass beads which are spread on the back of each decal. Pressure applied to these beads will cause them to break, and the decal will adhere immediately! Therefore, do not apply ANY pressure to the decal until it is exactly in the desired position.

  • Mix a normal dishwashing solution of water and any liquid dishwashing detergent in a shallow pan.
  • GENTLY lay the cabinet on its right side on a soft blanket.
  • Thoroughly clean the side of the game cabinet to ensure the removal of all dust.
  • Use a sponge to liberally apply the water and detergent solution over the entire side of the game cabinet.
  • Carefully place the rear left side panel decal, sticky side down, in the center of the wet surface of the game cabinet. Position the decal within 1/4-inch of the edges. Handle only the edges of the decal, and do not press any part of the decal. Use masking tape to position the edges of the decal exactly where they should be.
  • Use a squeegee to remove all the excess water and detergent from beneath it by quickly working from the center to the outside edges.
  • Carefully place the front left side panel decal, sticky side down, in the center of the wet surface of the game cabinet. Position the decal within 1/4~inch of the edges. Handle only the edges of the decal, and do not press any part of the decal. Use masking tape to position the edges of the decal exactly where they should be.
  • When the wrinkles are removed and the decal is free of all excess water and detergent solution, carefully upright the cabinet. Then GENTLY lay the cabinet on its other side on a soft blanket.
  • Repeat steps 2 through 8 for the decals that belong on the right side panels.
  • Carefully upright the cabinet.
Page 36

TM-255

ll.

12.

13.

14.

15. Sit—Down Cabinet

Use masking tape to position the edges of the front panel decal to within 1/4-inch of the edges of the front panel.

Use a squeegee to press the decal firmly and smoothly from the center to the outside edges of the decal.

GENTLY position the decal that has instructions for Pole Position II over the existing instructions on the control panel. Press the decal firmly and smoothly from the center to the outside edges of the decal.

Place the bonus points decal between the steering wheel and the shifter. Press the decal firmly and smoothly from the center to the outside edges of the decal.

Use a lint-free cloth to wipe off any excess water and detergent from inside and outside of the cabinet. Allow time to dry before proceeding.

Page 37

TM-255 Sit-Down Cabinet

INSTALL THE SELF-TEST CHART

  • Open the door at the rear of the game.
  • Remove and discard the self-test chart that is in place.
  • Staple the Pole Position II Self-Test Chart, ST-255, into place. (This chart contains important information about game settings.)

4, Close the rear door.

PERFORM A SELF-TEST

NOTE

It is important to perform the self-test after the enhancement modifications are completed!

  • Plug the game in.
  • Set the power on/off switch to the on position.
  • Perform the self-test procedure as described in CO-218-12 (Pole Position II Operator Information).

CHANGE THE POLE POSITION SCHEMATIC PACKAGE,

The Pole Position Schematic Package Supplement, SP-218, supports games with the Atari printed-circuit boards. The Pole Position Schematic Package Supplement, SP-219, supports games with the Namco printed-circuit boards. Refer to CO-218-12 (Pole Position II Operator Information) for changes to these schematic packages. Mark these changes into your schematic package!

After you have changed the schematic package, the enhancement procedure for the sit-down cabinet is complete.

Page 38

) iN ATARI, INC. 790 SYCAMORE DRIVE ® P.O. BOX 906

ATARI MILPITAS, CALIFORNIA 95035

408/942-3100 © TELEX 35-7488