CATHODE RAY TOMES

Vindicators TM-317 1st Printing

Vindicators (rev 5) (Atari Games, 1988) · Technical Manual · 64 pages · 79 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

For technical assistance:

If reading through this manual does not lead to solving your game maintenance or repair problem, call TELEHELP® at one of these Atari Games Customer Service offices:

UNITED STATES Atari Games Corporation

California Customer Service Office 737 Sycamore Drive P.O. Box 361110 Milpitas, CA 95035 Fax (408) 434-3945 Telex 5101007850 © (408) 434-3950 (Monday-Friday, 7:30 a.m.-4:00 p.m. Pacific time)

EUROPE

Atari Games Ireland Limited

European Customer Service Office Tipperary Town, Ireland

Fax 062-51702 Telex 70665 © 062-52155 (Monday-Friday, 9:00 a.m.—5:30 p.m. GMT)

Page 3

a GAMES

~ Operators Manual

Vindicators

with Illustrated Parts Lists

Page 4

© 1988 by Atari Games Corporation. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private usc, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976 This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles, In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

4s Printed in the U Vindicator

Page 5

Vindicators

Notice Regarding Non-Atari» Parts

WARNING Use of non-Atari parts or modifications of

any Atari game circuitry may adversely affect

the safety of your game, and may cause injury to you and your players

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.

NOTE

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:

  • All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three wire outlet. ¢ On games provided with an Electromagnetic Interference (EMI) ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

iii

Page 6

nN Table of Contents

Set-Up How to Use This Manual.....-...0..c:se wearee eeeatinnye Inspecting the Game.............. z 1 Control and Switch Locations. Setting the Coin and Game Options.

Self-Test RAM/ROM Tes Switch Test ..... Coin Options Game Optio Statistics ... Histogram . Playfield Te VHB

a WU AQUA KER

a Motion Obiect Te: Alphanumerics ‘f¢ Color Test. Color Purity Test Convergence Test. Sound Test...... Maintenance Preventive Maintenance ......0000...0....00 Preventive-Maintenance Intervals Removing the Control Panel ... Cleaning the Push-Button Leaf switche Tank Controller cones Cleaning the Coin Mechanism Cleaning the Interior Component: Corrective Maintenance.. Removing the Tank Controiler. Disassembling the Tank Controller Reassembling the Tank Controller. Removing the Vicleo Display. Replacing the Video Display Removing the Game PCB.. Removing the Fluorescent Light Removing the Speaker: Troubleshooting Troubleshooting Aids... Troubleshooting Technique: Soldering Techniques a a Troubleshooting Static-Sensitive Device AS cea cexszeats ceeunsesa cacanenereeenss savvceennansanauvces HE Illustrated Parts Lists Vindicators Coin Information and Game Statistics Glossary Warranty KRROdGddGRD WG a Vindicators

Page 7

Vindicators

List of Illustrations

Figure 1-1

Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14

Figure 3-1 Figure 3-2 Figure 3-3

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4

Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7

Table 1-1

Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5

Table 3-1 Control and Switch Locations

RAM Test F ROM Test F Switch Test Coin Option. Game Options Statistics Histogram. Playfield Test Motion Object Te. Color Test........... Alphanumerics Test ... Color Purity Test Convergence Test e . SOU TSE sss cos ccsersenrassassegsngenenisersachanonerisnssavatatsccaveesennssstatvecsayecen ase

Leaf Switch and Tank Controller Removal..... Tank Controller Disassembly and Lubrication... Control Panel, Video Display, and Speaker Remov

Removing IC (Cut-Pin Method) Removing IC Pins . Removing Solder from Plated-Through Holes Removing Solder from Lead Connection Pads..

Cabinet-Mounted Assemblies Control Panel Assembly .. Tank Controller Assembl Switching/Linear (SL) Power Supply ‘Assembly . Coin Acceptors, Inc. Coin Door Assembly Vindicators Game PCB Assembly ... Stand-Alone Audio PCB Assembly.

List of Tables

Game Specifications .....0.0.0. csc cteeeeetetteesees

Faulty RAM Locations........ eeananadiehedies enn Faulty Upper or Lower Main ROM Locations. Game Options .. Moiion Object Test Description Faulty Sound RAM and ROM Locations ...

Recommended Preventive-Maintenance Intervals...

Page 8

vi

Safety Summary

‘The following safety precautions apply to all game operatoss and scrvice personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should be only be plugged into a grounded three-wire outlet. If you have only a Wwo-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servi ing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voluiges continue to exist even after power is disconnected in the display circuitry and the cathode-ray tebe (CRT), Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. \f you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation,
CAUTION Properly Attach AH Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not lorce them, If you reverse a connector. it may damage your game and void your warranty, Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must noi be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operaies on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check che product identification label on your machine for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:
NOTE—A highlighted piece of information.
CAUTION—Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit bourds, pars thereon, and video displays if equipment or pans are damaged or destroyed due (0 failure of following instructions
WARNING—Piayers and/or technicians can be killed or injured if instructions are not followed. Vindicators
Page 9

Set-Up

How to Use This Manual

This manual is written for game Operators and service personnel, and provides information for setting up, playing. testing, and maintaining your Vindicators™ game. The manual is divided into the following chapters:

  • Chapter 1 contains set-up and game play information.
  • Chapter 2 contains self-test procedures.
  • Chapter 3 contains preventive and corrective maintenance procedures.
  • Chapter 4 contains troubleshooting information.
  • Chapter 5 contains illustrated part lists. Wiring and schematic diagrams for the Vindicators game Circuitry are contained in the Schematic Package Supplement (SP-313) included with your game. This chapter includes information required to set up and play your Vindicators game. Carefully read the information in this chapter before applying power.
Page 10

Set-Up

WARNING. To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area. This cabinet should be connected to a grounded three-wire outlet only. If you have only a twowire outlet, we recommend that you hire a licensed electrician to install a grounded outlet. Players can receive an electrical shock if the cabinet is not properly grounded

Inspecting the Game

‘WARNING Do not plug in the game until you have completed the following inspection steps.

Please inspect your Vindicators game carefully to ensure that the game is complete and was delivered to you in good condition. Figure 5-1 shows the locations of the component parts of the game. Table 1-1 lists space, power, and environmental requirements, Inspect the factory-assembied game as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts. N . Unlock and open the rear access panel. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed edge connector can damage a printed-circuit board (PCB) and will void your warranty.

Table 1-1 Game Specifications

Characteristic Specification

150 V-A, 120 W RMS +5° to +50° C (+37° to +122° F) Power Consumption Temperature

Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. games) Width 27 in, (69 cm) Depth 39 in. (99 cm) Height 71 ip. (80 em) Weight 302 Ibs. (137 kg) Vindicators

b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation, d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. e. Inspect other major suly-assemblies, such as the video display, printed-circuit boards (PCBs), and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Control and Switch

Locations

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 5-1.)

Volume Control The volume control is located on the Audio PCB behind the upper coin door. (See Figure 1-1.) The volume contro} adjusts the level of sound produced by the game.

Self-Test Switch The self-test switch is located to the left of the volume control on the Audio PCB behind the upper coin door. (See Figure 1-1.) The self-test switch selects the Self- Test Mode to check game operation. Refer to Chapter 2 for a complete description of self-test operation.

Coin Counter

The coin counter is located on the shelf inside the upper coin door. The coin counter records the number of coins deposited.

Setting the Coin and Game Options

The Vindicators coin and game options are set in the Self-Test Mode, Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This section of the manual describes the theme of the Vindicators game and the game play features.

Introduction Vindicators is a One- or Worf tank game with a continueus buy-in feature, allowing players to join in

Page 11

Vindicators

Self-Test Switch

Auxiliary Coin Switches

Coin Counter Sectip

Stand-Alone Audio PCB

Volume Control

Figure 1-1 Control and Switch Locations at any time. A color-coded control panel (left player/blue and right player/red) and game character allow for instant identification by players. Each player has a special tank convoller with thumb and tigger buttons. The iank controller is used to steer and command an arsenal of weapons. Players pick up fuel to stay alive and stars (0 customize their tanks. With these stars, an arsenal of weapons and super powers can be purchased. Players can also select their starting points and are rewarded with a cache of stars for accepting a greater challenge.

Play Mode

Vindicators takes place in the year 2 Galaxy TRIS. The mission is to intercept and de: the invading forces from the evi] Tangent Empire, The goal is to proceed through multi-level stations, securing each by demolishing its control center. The weapon is the SR-88 Strategic Battle Tank. As tea commanders of these SR-88 Strategic Battle Tanks, the players must face the invading forces from the Tangent Empire. The invaders have 14 space stations equipped with turrets and highly mobile armored tanks that constantly patrol the Tangent’s fortifications. The SR-88 battle tanks are powerful, but their fuel supply is very volatile. The players must constantly replenish their fuel supply by picking up fuel canisters at the many levels of the stations. Battle stars are also found along the way which provide enhancements such as:

¢ increased shot range

  • increased shot power
  • increased shot speed
  • force shields
  • smart shots
  • bomb cannons
  • tank armor,

Maximizing Earnings

Operator options on this game have been kept very simple. You should thoroughly read Chapter 2, Self- Test, for information on the Coin Options, Game Options, Histogram, and Statistics screens that you can effectively use the available options, Use the Self-Test screens showing Statistics and Histogram to evaluate game data, and the Game Options screen to make adjustments. (Refer also to the Self-Test chapter for more information on setting options.) The key to maximum earnings is striking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be long cnough to give ph sa good value and ensure repeat play. (Repeat play is crucial to longevity.) The Vindicators software gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjustments If collections seem low or are dropping off, check all player controls and coin mechanisms for proper operation. If earnmys seem low, the game is technically sound, and the average game time per quarter is under 150 seconds, try changing the game-difficully option to an sier setting. This change will give players more game time for their money

Page 12

Set-Up

If the average game time per quarter is over 270 seconds, first try changing the game difficulty to a harder setting. If the average game time per quarter is still over 270 seconds after a few weeks, try an even harder setting.

NOTE Be sure to keep the factory default at “no” if you wish to try other than factory-recommended settings.

After changing the game-difficulty settings, it is a good idea to reset the game statistics. The coin information and game statistics should be cleared in self-test by

1-4 Vindicators,

pressing the Player 1 right Fire button, this resets the average game time statistic. In addition, the histogram should be cleared by pressing the Player 1 right Fire button while displaying the Histogram screen

Special Contest Feature

Vindicators includes a special contest feature that offets players the opportunity to win a free Vindicators T-shirt. After successfully completing the contest round, players will be asked to input their name, age, and birth date. A five-character code will be given to players to send to Atari Games for verification, T-shirts are limited to quantities on hand, and the contest is void where prohibited by law. All entries must be postmarked no later than October 1, 1988, to be valid.

Page 13

Chapter 2

Self-Test

The Vindicators™ game tests itself and provides visual and audible indications of the condition of the game ciscuitry and controls. Self-test information is displayed on the screen and through the sound system. No additional equipment is required.

We suggest that you perform a self-test when you first

set up the game, each time you collect the money, or when you suspect game failure. Thirteen self-test screens provide information pertaining to the game circuits and controls. The game enters the Self-Test Mode after the self-test switch is turned on. The following self-test screens are arranged in the sequence in which they occur when the self-test switch is turned on. After the Sound Test, the sequence starts over with the Switch Test. Turning the self-test switch off at any time during the Self-Test Mode causes the game to return to the Attract Mode.

Refer to Chapter 1 for the self-test switch location.

Page 14

Self-Test

RAM/ROM Test The RAM/ROM Test screens are shown in Figures 2-1 and 2-2.

This test provides a visual check of the game RAM, ROM, and associated circuitry. If the RAM and ROM Test passes, the display advances to the Switch Test.

Figure 2-1 RAM Test Fails

Figure 2-2 ROM Test Fails

Table 2-1 Faulty RAM Locations RAM Type Location Video Display Characteristic on Game PCB Background color is dark green and foreground is bright blue. Background color is dark green and foreground is bright blue Background color is dark brown and foreground is light blue. Background color is dark brown and foreground is light blue, Upper PF/MO 2M

Lower PF/MO. IN

Upper aL/CPY IM

Lower AL/CPU 2N

Upper Color RAM 18K Lower Color RAM 16K Reddish or brightly colored Blues and greens will be the prevalent colors

_ . = 4

2-2 Vindicators

The RAM/ROM Test is divided into uve sections. ‘The RAM Test is performed first. If the RAM Test passes alter a six-second delay, the self-test skips to the ROM Test without displaying any message. If the RAM fails, a message will be displayed in the upper left of the sereen as shown in Table 2-1. The RAM Test will continue to run until it passes. If the Player 1 left Fire button is pressed and released, the RAM Test will advance to the next RAM or ROM Test.

The ROM Test will display no messages and advance io the Switch Test if no errors occur. If a ROM fails, a message is displayed. Table 2-2 shows the location of the failing ROM, If the Player 1 left Fire button is pressed and released, the ROM Test will advance tc the next test.

Table 2-2 Faulty Upper or Lower Main ROM Locations

Error Address Location on Game PCB

00000U=1DL=3D
20000U=1FL=3F
40000U=1KL=3K

Switch Test

The Switch Test is shown in Figure 2-3. This test checks the condition of the player controls. The tank controller movement and the buttons that are checked include: Left Player: Right Player: L Fire L Fire R Fire R Fire L Thumb L Thumb R Thumb R Thumb LUp LUp RUp R Up L Down L Down R Down R Down Left Player Stan Right Player Start Spare 1 Spare 2 Spare 3 Spare 4 Spare 5 Spare 6 Press the Player 1 left Fire button for the next screen. Operate the tank controller and pushbuttons for the right player first, and then the left player. Check that the screen highlights in grey the appropriate tank conwoller movement or button that was pressed. If any Spare message is highlighted, you may have a hardware problem and the game play may not work correctly,

Page 15

Vindicators

1 qulton Teet

HE URE

ist pare pare ert fire PPS nent’ Screen AP

Figure 2-3 Switch Test Press the Player 1 left Fire button to obtain the next screen,

Coin Options

The Coin Options screen is shown in Figure 2-4. The Coin Options screen indicates the current coin option settings and is used to change those settings COIN MODE should have a red box around it. Move the player 1 right control up or down to cycle through four game price selections as follows:

  • One Coin (Default)
  • Two Coins
  • Three Coins
  • Four Coins Select the desired value. Note that the default (recommended) setting of One Coin is highlighted in green. Move the player i left control down to move the red box to RIGHT MECH MULTIPLIER. Then move the player 1 right control up or down to cycle through four multiplier selections as follows:
  • 1 Coin Counts as 1 Coin (Default)
  • 1 Coin Counts as 4 Coins
  • 1 Coin Counts as 5 Coin
  • 1 Coin Counts as 6 Coins

‘Coin Options:

fae 4 vlobt FE phenteres sr iapgad setting Pi TEE UTE Tine anaenit

Figure 2-4 Coin Options Self-Test

Select the desired value. Note that the default Gecommended) setting of 1 Coin Counts as 1 Coin is highlighted in green. Move the Player 1 left control down to move the red box to LEFT MECH MULTIPLIER. Then move the Player 1 right control up or down to cycle threugh two multiplier selections as follows:

  • 1 Coin counts as 1 Coin (DefaulD
  • 1 Coin counts as 2 Coins Select the desired value. Note that the default (recommended) setting of 1 Coin counts as i coin is highlighted in green. Move the Player 1 left control down to move the red box to BONUS ADDER. Move the Player 1 right control up or down to cycle through seven bonus adder selections as follows:
  • No Bonus Adder (Default)
  • 2 Coins Give 1 Extra Coin 4 Coins Give 1 Extra Coin 4 Coins Give 2 Extra Coins 5 Coins Give 1 Extra Coin 3 Coins Give 1 Extra Coin «Free Play Select the desired value. Note that the default (recommended) setting of No Bonus Adder is highlighted in green. eee

If you replace the EEROM at location 1C or if a hardware problem occurs, the coin options will switch to the default (green) settings. If you want to cancel the coin option changes and restore the original settings, press the Player 1 right Fire button. Press the Player 1 left Fire button to set the game for the options selected and obtain the next screen. Exiting from the Coin Options screen by turning off the self-test switch will not set the game for the selected coin options.

Game Options

The Game Options screen is shown in Figure 2-5. This screen indicates the current game-option settings, and is used to reset the high score table and change the game-option settings. Refer to Table 2-3 for the available options and the default (recommended) settings.

Note that the default settings are highlighted in green. Move the Player 1 right control up or down and note that the settings in the red box change. Select the desired value. Move the Player 1 left control up or down to move the red box to the desired option.

Move the Player 1 right control up or down to cycle through all the available game option settings and se-

Page 16

Self-Test

Gane Options gegToRe FACTORY OPTIONS SPECIAL COST DIFFICULTY LEVEL STARTING FUEL CONTEST CLEAR HIGH SCORE TABLE Ww MORE Ww t fine Siok setting

Figure 2-5 Game Options

Table 2-3 Game Option Settings Option Name Ayailable Settings

Restore Factory OptionsNo #Yes

Special Cost No Special Cost i Two Credits to Start; One to Continue +

Difficulty LevelEasyModerate #

Hard Hardest

Starting FuelEasyModerate #

Contest Allowed + Disabled

Ciear High Score TableYesNo #
Music in Atract ModeYes #No
Auto High-Score-TableYes +No

Reset + Manufacturer's recommended settings

lect the desired value. Repeat this procedure for the remaining options. Restore Factory Options—Restores game options to default settings. Special Cost—Requires 2 credits to start and 1 to continue action.

Difficulty Level——Conwols overall difficulty level of game, Starting Fuel—Controls the quantity of starting fuel at beginning of game. Contest—Determines whether the contest is available. Clear High Score Table—The high score table is not reset unless you select Yes.

Music in Attract—Determines if music is played in Attract Mode. Auto High-Score-Table Reset-—Automuatically resets the high-score table after 2000 games if no player has achieved a high score in the last 200 games. Vindicators

If you want to cancel the option changes and restore the original settings, press the Player 1 right Fire button.

Press the Player 1 left Fire button to set the game for the options selecied and obtain the next screen. Fxiting the Game Options screen by turning off the selftest switch will not set the game for the selected options,

Statistics

The Statistics screen appears as shown in Figure 2-6. This screen provides a visual check of the current game statistics. The statistics information is accumulated either from the first time the game was turned on or from the last time the statistics were reset. To reset

88 seo

Pregs Player { right fire es Clear’ stathtthos Press Player t Left Fire Samarioga 15:49514° “O48b8ISe8 09126:

Figure 2-6 Statistics the statistics information, press the Player 1 right Fire button. The following information appears on the Statistics screen:

¢ Left Coins shows the number of coins deposited in the left coin mechanism. ¢ Right Coins shows the number of coins deposited in the right coin mechanism.

  • 0 Plyr Mins shows the minutes of idie time.
  • 1 Plyr Mins shows the minutes played as a \-player game.
  • 2 Plyr Mins shows the minutes played as a 2-player game. ¢ Easy Games shows the number of players who started at the easy level. ¢ Medium Games shows the number of players who started at the medium level

¢ Hard Games shows the number of players who started at the hard level.

  • Joined Games shows the number of players who joined while a game was in progress.
Page 17

Vindicators

¢ Total Games shows the total number of games played. One “game” is the time between a player starting and that player dying, regardless of time or number of coins inserted.

  • Frror Count shows the number of EEROM errors that were detected. Replace the EEROM at location 1C on the Game PCB if the errors detected exceed approximately 75 per week. ¢ Total Coins shows the total number of coins deposited in all the coin mechanisms.
  • Avg Time/Coin shows the average game time per coin, in seconds, for all players.

Press the Player 1 left Fire button to obtain the next Playfield Test

screen, :

Histogram

The Histogram screen is shown in Figure 2-7. The histogram shows the average game time from 0 to 600 or more seconds. The Histogram also provides a corresponding bar graph.

Laver 4.2: itr Sat

Figure 2-7 Histograms The game times information is accumulated either from the first time the game was turned on or from the last time the game times were reset. To reset the Histogram, press the player 1 right Fire button when in the Histogram screen.

screen.

The Playfield Test is shown in Figure 2-8. Under the ttle PLAYFIELD TEST bank number is indicated. Each bank refers to a graphics block in hardware. There are six banks. By pressing the Player J left Thumb button, each bank is sequentially accessed, The Player 1 right Thumb button cycles through the bank backwards. The valid banks are 0 through 5. Other banks will not give a cohesive picture and should be ignored. By moving the Player 1 left tank controller up and down, vertica} scrolling is achieved. Moving the Player i right tank controller up and down gives horizontal scrolling. Playfield banks 0, 1, 2, and 3 refer to EPROM locations 8/OR, 12/13R, 8/9P, and 12/13P.

ress ‘Vert fire for here tet ae

Figure 2-8 Playfield Test Playfield banks 4 and 5 refer to EPROM locations 7R, J4R, 7P, and 14P.

screen,

Motion Object Test

The Motion Object Test appears as shown in Figure 2-9. The Motion Object Test indicates the condition of the motion-object buffer circuit. There are seven objects placed in one row at the top of the screen. The following information is provided at the bottom of the screen: ¢ OBJECT indicates the number of the motion object selected,

° PICTURE indicates the stamp number in ROM.

  • HORIZONTAL indicates the horizontal position of the object.

Notion Opseot Test

Qoject roche, Ser Color Palette!

Dress Player 4 left Pire for het test

Figure 2-9 Motion Object Test

2-5

Page 18

Self-Test

  • VERTICAL indicates the vertical position of the object.
  • SIZE indicate the number of stamps high and wide.
  • COLOR PALETTE indicates the palette number for colors.

Perform the test procedure as described in Table 2-4 Press the Player 1 left Fire button to obtain the next screen.

Alphanumerics Test

The Alphanumerics Test is shown in Figure 2-10. This test indicates the condition of the slphanumerics circuit. Check that there are no errors on the screen. If there are errors, check the EPROM at N16 or its circuitry. Press the Player 1 left Fire button to obtain the next screen.

| Table 2-4 Motion Object Test Description Control/Movement Player 2 Left Fire Button (increment by 1) Function

Displays a different set of pictures, (See PICTURE.) Press this button to view the pictures from 0 to SFFF. If there ase errors, inspect: Picture EPROM location on Game PCB Board 8/9R 12/13R sop 12/13P 4000-SFFF 7R 14R 7P 14P Player 2 Right Fire Button (decrement by 1) 0-3FFF

Player 2 Left Thumb Button Player 2 Right Thumb Button Player 1 Left Tank Controller

Player 1 Right Tank Controller

Player 1 Left Thumb Button

Player 1 Right Thumb Button

Player 1 Right Fire Button

Player 1 Start Button

Player 2 Start Button Increments picture by size Decrements picture by size Moves the vertical position of object Moves the horizontal position of object |

Decreases the selected object number Increases the selected object number Increases the palette of the selected object Increases the vertical size of the selected object increases the horizontal size of the selected object

2-6 Vindicaors,

Figure 2-10 Alphanumerics Test

Color Test

The Color Test is shown in Figure 2-11. This test indicates the condition of the display color circuits The screen should show 16 vertical gray-scale bars and three blocks of red, green and blue, each containing 16 vertical bars. The brightest bars should be on the left and darkest (black) on the right, with a grey frame around the screen. This frame will help to identify the darkest color band. If the display characteristics are not correct, refer to the display manual! for the color-gun adjustment procedure or to determine the possible cause of failure. Yo adjust the brightness, find the darkest column (not black) with the red, green, and blue colors. This column should be just barely visible.

Press the Player 1 left Fire button to obiain the next screen.

prea

le: Cee next Lenton

Figure 2-11 Color Test

Color Purity Test

The Color Purity Test consists of five color displays that indicate the condition of the display color-purity circuits. The first display to appear should be a red screen with the word RED displayed at the bottom of the screen.

Page 19

Vindicators

Press the Player 1 right Fire bution, and the next di play to appear should be green with the word GREEN displayed at the bottom of the screen (see Figure 2-12). Press the Plaver 1 right Fire button to obtain a blue, white, and finally a gray screen. After the gray screen, the display will repeat the red, green, blue, white and gray sequence again.

Figure 2-12 Color Purity Test If the display characteristics are not correct, refer to the display manual for the color-purity adjustment procedure or the possible cause of failure. Press the Player 1 left Fire button to obtain the next screen,

Convergence Test

The Convergence Test is shown in Figure 2-13. This test indicates the condition of the display size, centering, linearity, and convergence. The grid pattern should be white Press the Player 1 right Fire button and the grid pat tern should turn violet. Pressing the Player 1 right Fire button again should cause the grid pattern to turn green. Check the grid pattern for the following characteristics (the violet and white patterns are used to adjust the display convergence):

  • The four corners of the frame around the grid pat-

2-13 Convergence Test Self-Test

tern should touch all four corners of the screen.

  • Gnd lines should show no pincushioning or barreling, and the lines should be straight within 3.0 mm. + Violet and white pattern convergence should be within 2.0 mm. Tf the display characteristics are not within these limits, refer to the display manual for the linearity and convergence adjustment procedures or to determine the possible cause of failure. Press the Player 1 left Fire button to obtain the next screen

Sound Test

The Sound Test is shown in Figure 2-14. This test indicates the condition of the coin mechanisms and the music, speech, and sound-effects circuits. The sound microprocessor is reset at the beginning of this test. The game may take up to three seconds to produce the first sound. If the sound-microprocessor reset fails, the message SOUND PROCESSOR NOT RE- SPONDING should blink near the top of the screen, If the sound microprocessor is good, check the coin mechanisms and the sound microprocessor circuits by observing the following messages:

  • CURRENT COIN VALUE consists of four zeros. The third and fourth zeroes correspond to the left and right coin mechanisms, respectively. These zeroes should change to ones when the coin switch is held down, and back to zeroes when it is released.
  • NUMBER OF SOUNDS indicates of the number of sounds used in the Vindicators game.
  • SOUND CPU STATUS indicates the condition of the sound microprocessor. If the sound microprocessor is good, the word GOOD should appears. If the sound microprocessor or associated circuitry is faulty, a number will appear (to indicate sound status) in addition to an error message located at the top of the screen. Refer to Table 2-5 for the error

Gound Test

GEER AEURSETTY °° So8 pert oe Sound’ cBG Sound @ ¢ 3 Good 4 Music Chip Test Press Player 2 right fire 10"hear 50 Move Player 4 bee tes See hie sbress Riguer 4 left Fire

Figure 2-14 Sound Test

Page 20

Self-Test

messages and faulty sound RAM and ROM locations on the Stand-Alone Audio PCB.

+ SOUND = indicates the sound selected by moving

the Player 1 right tank controller up (increments the sound number) or down (decrements the sound number). To hear the sound, press the Player 1 tight Fire button one or more times. Moving the Player 1 left control up or down or pressing the Player 1 right Thumb button silences the sound.

  • Sound 4 (Music Chip Test) consists of eight tones in a major scale that alternate between sound channels (46 tones in all).

* Sound 5 (Effects Chip Test) consists of four tones in

a major chord that come from both sound channels simultaneously. ¢ SCOM (serial communications) Reset Test checks that the Game PCB can reset the Stand-Alone Audio PCB.

Press the Player 1 left Fire button to return to the Switch Test. Vindicators

| Table 2-5 Faulty Sound RAM and ROM Locations

Frror Message

Music Chip Time Gut Sound CPU Interrupt Error Sound CPU RAM 1 Error

Sound CPU ROM I Error

Communications Error #1

Communications Error #2

Sound Processor Not Responding Location on Stand-Alone Audio PCB/Cause

2F

2F, 5K, Transistor Q8 21H

2K

If displayed when entering test, then sound processor cannot run further. Press Fire button to obtain next test

1M Will count number of errors caused by either the Stand- Alone Audio PCB or Game PCB. This error message usually means that the chip no. 137526-001 on either of these two boards is bad or is loose in its socket A probable disconnection of the Stand-Alone Audio PCB from the Game PCB. or the chip at 1M is not inserted into its socket.

A major problem with the Stand-Alone Audio PCB. If you cannot enter the self-test, the cause may be a hamess disconnection between the Stand-Alone Audio and Game PCBs

Page 21

Chapter 3

Maintenance

This chapter includes preventive and corrective maintenance procedures for the Vindicators™ game components that are subject to the most use. To assure maximum trouble-free operation from this game, we recommend that preventive maintenance be performed as described in this chapter. Removal, disassembly, re-assembly, and replacement procedures are provided for components that might require corrective maintenance. Appropriate references are provided to Chapter 5, Illustrated Parts Lists, to help locate the parts of this game that are mentioned, but not illustrated, in the maintenance procedures,

Page 22

Maintenance Vinclicators

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, j

WARNING and tightening hardware. How often preventive main- . } tenance is performed depends upon the game envi- To avoid possible electrical shock, turn off the ronment and frequency of play. However, for those game before performing any maintenance procecomponents listed in Table 3-1 Preventive-Maintenance dures. Intervals, we recommend that preventive maintenance i be performed at the intervals specified. Preventive-Maintenance Table 3-1 Recommended Preventive-

Intervals Maintenance Intervals

Tank Controller Inspect weekly, iubricate, and The preventive-maintenance intervals specified in tighten hardware at least e Table 3-1 are the recommended minimum require- ery three months. ments for the components listed. Coin Mechanism —_ Inspect whenever you collect coins. Clean at least every three months.

Control Panel

Control Panel Decal Hex Locknut

Flat Washer

Button Assy

Stamped Nut ontro! Panel Harness Assy

Leaf Switch

Figure 3-1 Leaf Switch and Tank Controller Removal

3-2

Page 23

Vindicawors

Removing the Control

Panel

Perform the following procedure to remove,replace the contro! panel. (See Figure 3-1.) J the tamper-pioof hex-key wrench Cincluded in the operators manual bag) to remove the four tamper-proof screws and washers holding the control panel to the cabinet

NOTE A hole is provided on the cabinet shelf inside the upper coin door to conveniently store the hex-key wrench when not being used. This hole is located to the left of the coin slots.

N . Grasp the tank controller and gently lift until the bottom edge of the contol panel clears the cabinet.

  • Disconnect the three control panel harness connectors and remove the control panel from the cabinet. 4, Replace the control panel in the reverse order of removal.

Cleaning the Push-Button

Leaf Switches

Perform the following procedure to clean the leafswitch contacts and tighten the securing hardware. (See Figure 3-1.)

  • Remove the control panel as previousiy described in this chapter. iy . Use electrical contact cleaner to clean the contacts. Do not burnish them. When the push button is pressed, the wiping action of the cross-bar contacts provides a self-cleaning feature. Then use the Self- Test to verify proper switch contact.
  • Use a 15/16-inch open-end wrench to tighten the stamped nur holding the push-button leaf switches to the control panel Replace the control panel in the cabinet in the reverse order of removal

Tank Controller

Preventive maintenance on the tank controller consists of:

  • Inspection of each snap-action switch to assure that the actuators ae not bent or deformed.
  • Lubrication of gach spacer, shaft, and pivot shatt Maintenance

Lubricating the Tank Controller

Perform the following procedure to lubricate each tank controller. (See Figure 3-1.) 1, Remove the contol panel as previously described in this chapter.

  • Use a 3/8" wrench to remove the four nuts holding the tink controller to the control panel.
  • Apply a small amount of lithium grease (Atari part no. 178027-001) between each spacer and tube handle. Repeat this procedure for each of the four spacers.
  • Apply a smali amount of lithium grease to the pivot shaft.
  • Replace the tank controller and the control panel. Cleaning the Coin Mechanism

Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air. Cleaning the Interior Components Perform the following procedure to clean the components inside the cabinet

Turn off the game power, but do not unplug the power cord before cleaning inside the cabinet. The power cord provides a ground path for stray static voltages that can be present on the cleaning tools

WARNING |
  • Unlock and open the rear access panel and display service panel.
  • Discharge the high voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a, Attach one end of a large, well-insulated, 18gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c. Wait ovo minutes and repeat part b.
Page 24

Maintenance

CAUTION | Be extremely careful when cleaning the electrical | components inside the cabinet. Avoid touching the | electrical Components with any solid object other | than the soft bristles of the vacuum attachment or | paint brush. |

Corrective maintenance consists of removal, disassembly, re-assembly, and replacement of game components. The following procedures are provided for components that may require corrective maintenance.

Removing the Tank

Controller

Perform the following procedure to remove/replace the tank controller (See Figure 3-1.)

  • Remove the control panel as described under Preventive Maintenance.

Socket Head Screw

Left Handle Cover

Pan Head Screw

Microswitch Bracket

Snap-Action Switch Vindicaors

  • Use a vacuum cleaner with a soft long-bristied brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabmet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.).

Corrective Maintenance

  • Use a 3/8-iach hex driver to remove the four nuts holding the tank controller to the control panel.
  • Carefully lift the tank controller out of the control panel.
  • Repiace the tank controller in the reverse order of removal

Disassembling the Tank

Perform the following procedure to disassemble the tank controller. (See Figure 3-2.)

Button

Jumper Wire Nae ~~- Control Harness Assy Switch A oo Button Joint

Keyboard Switch

Right Handle Cover

Figure 3-2 Tank Controller Disassembly and Lubrication

Page 25

Vindicators

nN

vi

10.

roy

12. Remove the covers from the handles using a 4mm socket wrench to remove the four M4 x 18mm socket head cap screws. Remove the button joint and button from the switches: Unsolder the harness from the PCB and switches, and slip the harness through the handle, as shown in Figure 3-2. Remove the retaining ring from the end of the pivot shaft. Remove the washers from the shaft, and remove the shaft from the tube and the frame. Remove the retaining ring attached to the tanslator shaft that protrudes beyond the handle tube. Remove the flat washer and retaining ring from the other side of the translator shaft. Remove the actvator shaft, including the washer and spring, through the handle tube. Remove the slip washer and slip spsing from the actuator shaft, and remove the actuator shaft from the frame. Repeat the procedure in Step 5 above for the other handle tube. . Remove the handles and tubes from the slides and spacer frame. Note the orientation of the handles for subsequent re-assembly. . Remove the handles from the tubes. Remove the slides from the spacer frame. Remove the spacer and the top plate from the frame by removing the #10 nut and lock washer. -Remove the retaining rings from the shaft, slip the bumper stop off the shaft and slip shaft from the frame. Repeat this procedure for the other bumper stop.

Reassembling the Tank

Controller

Perform the following procedure to reassemble the tank conwoller. (See Figure 3-2.)

v

we

we Slip the bumper stop shaft partially through the frame. Then slip the bumper stop over the shaft. Push the shaft through the other side of the frame. Install the retaining rings. Repeat Step 1 for the other bumper stop shaft. Mount the frame spacer, nylon washer, and top plate on the frame. Secure using four #10 lock washers and nuts. Slip the slide handle in the spacer frame as shown in Figure 3-2. Slip the left and right side handles over the left and right side tubes, respectively. . Slip the handle/tube assemblies through the slide Maintenance

handle and spacer frame. Note the proper orientation of the handles. . Place the switch actuator shaft partially through the frame. Place the actuator shaft spacer over the switch actuator shaft, and push the switch actuator shaft through the handle/tube assemblies. Place the washer and spring on the actuator shaft, and push the shaft until it protrudes on the other side of the frame. Install the translator shaft through the actuator shaft as shown. Mount the flat washer and retaining ring on the translator shaft protruding handle/tube. Apply a small amount of lithium grease to the parts. Repeat Step 7 for the other handle/tube assembly. Insert the pivot shaft through the frame and the tube, slip the nylon washers over the shaft, and continue pushing the shaft until it protrudes on the other side of the frame. Install four retaining rings to secure the pivot shaft. Q. Place the wiring harness through the handle tubes as shown, and solder to the switches and PCB. . Mount the button joint and button on the keyboard switches.

  • Install covers on the right and left handles using four M4 x 18mm socket head cap screws.

Removing the Video Display

Perform the following procedure to remove/replace the video display. (See Figure 3-3.) 1. Turn the game power off and wait two minutes. Unplug the power cord. Use a 1/8-inch hex driver to remove the five screws holding the speaker gritle to the cabinet. Remove the speaker grille.

WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize Xradiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry, Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.

3-5

Page 26

Maintenance

  • Remove the video display shield. 4, Carefully remove the bezel from the protective foam tape.

wn Use a 1/8-inch hex driver to remove the four screws holding the upper rear door.. Remove the door.

  • Be sure that the game power is turned off before discharging the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Atach one end of a large, well-insulated, 18gauge jumper wire to ground Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.

¢. Wail two minutes and repeat part b. ~ From the rear of the cabinet, disconnect the display harness connectors from the display.

Attraction Frame Attration Cover Attraction Decal

Split-Lock Washer Washer Nut yoo cores tcc ae 4d

Control Panel Vindicators

WARNING To avoid dropping the video display, use exureme care when removing the display from the cabinet We recommend that nc one weighing less than 150 pounds should attempt to remove the display. In addition, we recommend that you wear gloves to protect your hands from the sheet-metal edges
  • Use a 7/16-inch nut driver to remove the four nuts holding the display to the cabinet
  • Carefully lift the display out through the front of the cabinet
NOTE Whenever the cathode-ray tube and yoke are replaced as a single unit, readjust the brightness, size, and centering as described in the display manual. Check the purity and convergence also according to the display manual instructions, but adjust both only if required.

Speaker Grille Black Vinyl Foam Tape

Upper Rear Door

41/2” Round Speaker

Fluorescent Light Fluorescent Lamp Fixture o— Clip

Page 27

Vindicators,

  • Replace the video display as described in the following procedure.

Replacing the Video Display

Perform the following procedure to replace the video display in the cabinet. (See Figure 3-3.) i. Carefully lift the video display. through the front of the cabinet.

  • Position the display so that the four holes in the video display mounting brackets align with the four studs in the cabinet.
  • Tighten the four mounting nuts and washers holding the mounting brackets to the cabinet studs. 4, Use a 7/16-inch nut driver to tighten the nuts with washers securing the display to the cabinet. Be sure that the display is centered horizontally.
  • Connect the display harnesses to the display.
  • Replace the bezel, display shield, and speaker grille.

Removing the Game PCB

Perform the following procedure to remove/replace the Game PCB.

  • Turn the game power off.
  • Unlock and remove the rear access panel from the cabinet.
  • Disconnect the harness connectors from the Game PCB.
  • Use a Phillips screwdriver to remove the two screws and washers holding the Game PCB to the cabinet.
  • Grasp the edge of the Game PCB and gently lift it out of the slotted guide.
  • Replace the Game PCB in the reverse order of removal.

Removing the Fluorescent Light

Perform the following procedure to remove/replace the fluorescent light. (See Figure 3-3.)

  • Turn the garne power off.
  • Use a 1/8-inch hex driver to remove the eight screws holding the attraction frame to the top of the cabinet. Remove the frame. Maintenance
  • Remove the light box plastic shield. as . Remove the fluorescent light from the light fixture.
  • To remove the entire light fixture, use a 1/8-inch hex driver to remove the four screws holding the upper rear door at the rear of the cabinet. Remove the door.
  • Disconnect the light harness connector in the rear of the cabinet.
  • Use a Phillips screwdriver to remove the two screws holding the light fixture. Remove the light fixture.
  • Replace the fluorescent light and/or light fixture in the reverse order of removal.

Removing the Speakers

Perform the following procedure to remove/replace the speakers. (See Figure 3-3.) 1, Turn the game power off.

  • Use a 1/8-inch hex driver to remove the five screws holding the speaker grille to the cabinet. Remove the grille. 3, Use a 1/8-inch hex driver to remove the eight screws holding the attraction frame to the cabinet Remove the frame.
CAUTION Do not touch the speaker cones when handling the speakers. The cone material is fragile and can be easily damaged.

4, Use a Phillips screwdriver to remove the four screws holding the speaker to the cabinet. Do not let ihe speaker fall,

  • Lower the speaker just far enough to disconnect the two speaker wires.
  • Replace the speaker in the reverse order of removal. Be sure that you hook up the wires correctly. Otherwise, the game will produce less than the desired volume because the speakers will be out of phase. The signal wire on each speaker should be attached to the speaker tab marked with color, a “+” sign, or a round dot. (The signal wires are shown on the game wiring diagram; refer to the Schematic Package included with the game.)
Page 28

Maintenance

N Vindicators

S

Page 29

Chapter 4

Troubleshooting

The information in this chapter discusses troubleshooting aids and techniques to assist the service technician when trouble is suspected in a game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your local distributor or your Atari Games Corporation Customer Service Office, listed on the inside front cover of this manual, for assistance.

NOTE | We recommend that uoubleshooting and repair | procedures be performed by a qualified service technician.
Page 30

‘Troubleshooting

Troubleshooting Aids

‘troubleshooting aids are provided in this manual and in the schematic package supplement. The most useful of these are:

Assembly and Component Locations

The locations of assemblies and components are in the paits lists in Chapter 5 of this manual. The. Printed-circuit board (PCB) illustrations can aid in rapidiy locating components shown on the corresponding schematic diagram(s).

Diagrams

The schematic package supplement for this manual contains schematic diagrams with component locations, active component type numbers, and electrical values.

Troubleshooting Techniques

| WARNING

To avoid electrical shock, turn off the game power before attempting to troubleshoot this game.

The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component. Check Fuses Check for open fuses. Refer to the power supply parts list in Chapter 5 and to the schematic package supplement for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.

Check Power-Supply Voltages

If all circuits are operating improperly, this usually indicates a power supply problem. Be sure that the proper line voltage is available to the power supply. Refer to the label on the power supply for its voltage rating Locate the Trouble Decide what the symptom is. Perform the self-test procedure provided in Chapter 2 of this manual. Use the wiring diagrams in the schemutic package supplement to determine which assemblies or mator circuits may be causing the trouble. Vinchaators,

Visual Check Visually check for obvious problems in the portion of the game where the trouble is suspected. Fer exarnple, check for loose or defective solder connections, interated circuits loose in their sockets, loose cable connections, broken wires, and damaged PCBs er components.

Check Individual Components

Check soldered-in passive components (e.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry. Often, the most practical way to determine if a component is faulty is to substitute a new component. Before you do this, make sure that you do not have some other circuit problem that could damage the new component.

Repair the Assembly

CAUTION

Soldered-in transistors and integrated circuits are difficult to remove without damaging the print | ed-circuit board or component. Refer to the information in this chapter pertaining to soldering | and replacing integrated circuits and transistors.

Repair or replace the defective part. Refer to Chapter 4 and information in this chapter for special removal and replacement procedures. Check for proper operation of the repaired circuit.

Soldering Techniques Observe the following recommendations when removing or replacing components soldered to a PCB. You can damage a PCB or heat-sensitive electrical components with poor soldering practices. Choose the proper soldering iron before you attempt to remove or replace soldered-in components. Excessive heat from a soldering iron is a common cause of damage to a component or PCB. Also, transient voltages from solder guns or improperly grounded soldering irons can damage certain voltage-sensitive semiconductor devices. Refer to Troubleshooting Static-Sensitive Devices for more specilic information. We recommend 2 15- to 27-watt pencittip soldering iron to avoid separating the etched circuit wiring from the board material and to avokl damaging active cony ponents. You cun also use a temperature-controtled soldering station rated at 700° F with a fine cone or a very fine chisel tip.

Page 31

Vindicators,

CAUTION Do not use a solder gun to remove or replace | soldered-in components on a printed circuit board. A solder gun can overheat a device, and its large transient voltage can damage a voltagesensitive device. | J

You will also need the following additional equipment for removing and replacing soldered-in components:

  • Solder Sucker—Hand-operated vacuum tool to remove liquified solder from the PCB. We recommend the top-of-the-line Soldapullt® brand. © Solder Wick—Resin-soaked copper braid to remove excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use of a solder wick on a multi-layer PCB with plated-through holes.
  • Flux Remover—Non-cortosive chemical to clean foreign material from the PCB before soldering and to remove any flux residue where components have been replaced. Also use it to clean any foreign material from the PCB during preventive maintenance. isopropyl alcohol is recommended. ¢ Acid Brush—Smail stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign material from the PCB.

Removing Integrated Circuits

The easiest and safest method for removing solderedin integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 4-1. Use the proper soldering iron as previously described under Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each pin in a random osder. Remove the loosened pin with the tip of the soldering iron or a needlenose pliers as shown in Figure 4-2. Allow a moment for the PCB to cool before proceeding to the next pin Apply just enough heat to remove any stubborn pins.

Diagonal Cutter

Figure 4-1 Removing IC (Cut-Pin Method) ‘Troubleshooting

Needle-Nose Pliers NN

Soldering Iron

Figure 4-2 Removing IC Pins For a multi-layer PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 4-3. If possible, suck the solder from the opposite side of the PCB trom where the heat is applied. Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 4-4,

| CAUTION

Do not use a solder wick to remove solder from inside plated-through holes. The heat required for the solder wick to remove the solder from in- | side the hole could damage the PCB. |

Use an integrated-circuit (IC) pulling too! to remove socketed ICs. Do not pry up on one end of the ICs because the pins could be bent or broken.

Troubleshooting Static-

Sensitive Devices

Certain precautions must be taken when working with static-sensitive devices, such as microprocessors, fieldeffect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LS!) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in a person's body or leakage from an improperly grounded soldering iron can cause static-sensitive device to fail, Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. A bate wire wrapped around your wrist and attached to an earth ground is effective when working extensively with static-sensitive devices. When soldering a static-sensi-

we

Page 32

Troubleshooting

se a: Solder Sucker

Preferred Method Soldering Iron Vindicators

Solder Sucker

Soldering Iron

Alternate Method

Figure 4-3 Removing Solder from Plated-Through Holes

Soldering Iron Solder Wick

Figure 4-4 Removing Solder from Lead Connection Pads tive device, use a soldering iron with a properly grounded three-wire cord. (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.)

Before you replace a static-sensitive device, make sure

it is actually defective. A static-sensitive device can appear defective due to leakage on a PCB. To make sure a device is defective, ground static voltages as described in the paragraph above. Clean both sides of the PCB with flux remover or an eraser. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Then test the device. New static-sensitive devices can be packaged in conductive foam or can have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Page 33

Chapter 5

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware parts, such as screws, nuts, washers, and so on, are not in the parts lists. The PCB parts lists are arranged in alphabetical order by component. Each component section is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Next come part numbers with a two number designation followed by a hyphen (00through 99-). Ending the list are part numbers with six numbers followed by a hyphen (000598- through 201000-). When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari Customer Service phone numbers are listed on the inside front cover of this manual.

Page 34

Tlustrated Pans Lisis Vindiewors

78-6900401 Biack Viny! Foam Tape 044925-01 99-11006 Atwaction Frame. Relaining Clip 045097-01 170003-001 Aitraction Cover Fluorescent Light 75-0458 045107-01 171086-001 Lock Washer Attraction Decal Fiuorescent Lamp Fixture uaa ron) 045095-01 Flat Washer Speaker Grille 75-9158 Hex Nut 139021-001 ne Video Display 1/2" x 1116" Foam, Tape 04510801 045106-01 Bezel Top Left Decal

| 176034-1812 _JJ Socket Head Screw 045105-01 Front Decal 045096-01 148007-003 Display Shield 41/2 Round Speaker A045136-01 Coin/Speaker Assy Harness

045109-01 A044248-01 Instruction Decat Tank Contro! Assembly 045148-01

Left Tread Decal

J A045039-01 Control Pane! Assy

176025-3620 Tamperproo! Screw a 75-015t ; Flat Black Washer. a, A043713-23

171027-001 Coin Door S.A. Audio Board Assy LY 178120-606 PCB Siandoff Suppor 038091-01 nase Cash Box . 5/32 ae ee ee Hi 171078-002 Lower Lelt Decal Key Wrench m Coin Counter

Figure 5-1 Cabinet Mounted Assemblies A045101-01 A

Page 35

Vindicator Ulustrated Parts Lists

A045135-01 Cabinet Assy Harness A044875-01 AC Power Assy Harness

A045045-01 Display Assy Harness A045134-01 Power Assy Harness A045133-01 045106-02 Com/Aud Assy Harness. Top Right Decat 045108-02 Water Deflector 178129-001 Wire Clip

037332-01 Vent Grille

045094-01 Upper Rear Door

045147-02 Lower Right Decal

045084-01 Rear Door 045146-02 Right Tread Decal

A044402-21 Vindicators Game PCB Assy

78-3201 ‘A043910-01 Adjustable Glide On/Off Harness Assy 178093-001 Fan Guard

A045140-01 S.L. Power Supply

Figure 5-1 Cabinet-Mounted Assemblies, Continued

Page 36

Illustrated Parts Lists Vindicators

Cabinet-Mounted Assemblies Parts List

Part No. Description

038091-01 Cash Box 044925-01 Attraction Frame 045084-01 Rear Door 045094-01 Upper Rear Door

045095-01 Speaker Grille 045096-01 Display Shield 045097-01 Attraction Decal Cover 045105-01 Lower Front Decal

045107-01 Attraction Decal 045108-01 Bezel 045108-02 Water Deflector 045109-01 Instruction Decal

045106-01 Top Left Side Decal 045 106-02 Top Right Side Decai 045146-01 Left Tread Decal 045146-02 Right Tread Decal

045147-01 Lower Left Side Decal 045147-02 Lower Right Side Decal 139021-001 19-inch Color Raster Video Display 148007-003 4 1/2-Inch Round Unshielded Speaker

170003-001 18-inch 15 Watt Fiuorescent Light 171027-001 25¢/25¢ U.S.A.Over/Under Coin Door 171078-002 12 V DC Non-Resettable Terminated Coin Counter 171086-001 18-inch Fluorescent Lamp Fixture 176025-3620 Button Head Tamperproof Screw 178056-002 1/2-Inch x 1/16-Inch Foam Tape 178120-606 0.375-Inch PCB Standoff Support 178126-002 5/32-Inch Hex Tamperproof Driver Key

75-015F 1/4-Inch, Black Flat Washer 78-6900401 1/4-Inch x 1/16-Inch Black Viny) Foam Tape 99-11006 Fluorescent Lamp Retaining Clip A0437 13-23 Stand Alone Audio Board Assembly

A043910-01 On/Off Harness Assembly A044402-21 Vindicators Game PCB Assembly A044875-01 AC Power Assembly Harness A045045-01 Display Assembly Harness A045099-01 Contro! Panel Assembly A045100-01 Cabinet Assembly A045133-01 Cony Aud Assembly Harness A045134-01 Power Assembly Harness

A045135-01 Cabinet Assembly Harness A045136-01 Coin/Speaker Assembly Harness A045140-01 SL Power Supply Assembly

wn

Page 37

Vindicators ilustrated Parts Lists

Part No. Description

The following items are the technical information supplements for this game: SP-317 Schematic Package ST-317 Self-Test Label TM-304 Sharp Color Video Display Service Manual 1M-317 Operators Manual

ye on

Page 38

Blusteated Parts Listy Vindicators oN 75-5116B Black Carriage Bolt A044248-01 Tank Contral Assy 045098-01 Control Pane!

045104-01 Jarret. 280 Control Panel Decal

Hex Locknut

. 75-0108 a Flat Washer N 78-6900402 ~~ Foam Tape

178030-003 Button Assy

75-9910NO Stamped Nut A045132-01 Control Pane! Assy Harness. 160013-001 Leaf Switch Figure 5-2 Control Panel Assembly A045099-01 A

Control Panel Assembly Parts List

Part No. Deserption

045098-01 Control Panel 045104-01 Conuol Pane! Decal 160013-001 Leaf Switch with Embossed Button Holder 17 7610-240 Polymer #10-24 Hex Locknut

178930-003 Black Button Assembly 75-0108 0 Flat Washer 75-5116B 4 Black Carriage Bolt 75-9910NO 5/8"-11 Starnped Nut

78-6900402 1/4-Inch x 1/8-lnch Thick Foam ‘Tape A044248-01 Tank Conuoiler Assembly A045 132-01 Contol Panel Assembly

Page 39

Vindiewors Mlustrated Parts Lists:

044968-01 172013-2818 Control Harness Assy Socket Head Screw — Gray, 040473-01 045164-01 178210-001 ~~ Jumper Wire Switch PCB Button 178209-002 ue _ Left Handle Cover oe “~~ _178210-002 Button Joint

160039-001 044400-02 Keyboard Switch Left Handle

044272-01 Top Plate

178209-001 Right Handle Cover 044400-01 178223-005 Right Hancle O-Ring

045165-01 Compression Spring 85-22F410 Pan Head Screw

107027-001 l 044404-01 Lithium Grease Microswitch Bracket

160042-002 Snap-Action Switch Figure 5-3 Tank Controller Assembly A044248-01 C

Tank Controller Assembly Parts List

Part No. Description

A044968-01 Control Harness Assembly 040473-01 Jumper Wire 044272-01 ‘Top Plate 044400-01 Right Handle

044400-02 Left Handle 044404-01 Microswitch Bracket 045164-01 Switch PCB 048165-01 Compression Spring

Lithium Grease 160039-001 Keyboard Switch 160042-002 172013-2818 M4 Socket Cap Head Blick Screw

178209-001 Right Handle Cover 178209-002 Left Handle Cover 178210-001 Button 178210-002 Button Joint 364 LD. x O70" Wide O-Ring

Page 40

Mlustented Parts Lists Vindicators,

WARNING

The switching power supply has high voltages on it when power is turned on. Theiefore, be sure you do not touch this power supply unless you have turned off the power to the game.

72-HA4806S 149003-xxx Screw 5V 10 Amp Switching Power Sunaly Assy a A043367-xx 179231-002 : 142042.001 Jumper Assy Terminal Block \ ¥ Transtornet

A043367-01 Jumper Assy 72-HA4B06S Screw

043396-01 Power Suoply Chassis Base

A042384-01 Line Filter Assy

46-2013002 Fuse

037640-01 Warring Label

179225-2205, or 79-3206 + se Bloc

034544-01 bane: Block Covet

043622-01 Fuse Latel 46-2012002 i

Figure 5-4 Switching/Linear (SL) Power Supply Assembly A045140-01 A

Page 41

Vindicators

Switching/Linear Power Supply Assembly Parts List tilustrated Parts Lists

Part No. Description

A042384-01 A043367-01 A043367-02 A043367-03

46-2012002 46-2013002 72-HA4G606s 72-HA4806s

034544-01 037640-01 043396-01 043622-01 Line Filter Assembly Jumper Assembly 6-Inch Black Jumper Assembly 6-Inch White Jumper Assembly

2 Amp 250 V Slow Blow Fuse 3 Amp 250 V Slow Blow Fuse 6-32 Threat-Forming Screw 8-32 Thread-Forming Screw

Fuse Block Cover Power Supply Warning Label Power Supply Base Chassis Power Supply Fuse Label

142048-001 Transformer 149003-003 Hitron 5V 10A Switching Power Supply 17922: 5 5 Position Fuse Block (Acceptable substitute is past no. 79-3206) 179231-002 2 Position Terminal Block

Hitron 5-Volt Power Supply Sub-Assembly Model HSA-122B(S) Parts List

DesignatorDescriptionPart No.

Capacitors cl Capacitor, Metal Film, 0.047 EF, 250 V C2 Capacitor, Metal Film, 0.1 F, 400 V C3, C4 Capacitor, Ceramic, 4700 pF, 400 V

C5, C6Capacitor, Electrolytic, 100 pF, 200 V99-2 11046
c7Capacitor, Metal Film, 0.1 iF, 400 V99-211038

C8 Capacitor, Ceramic, 0.001 pF, 2 kV

(oo)Capacitor, Ceramic, 0.01 pF, 1 kV, Z5U99-211041
cioCapaciior, Electrolytic, 220 uF, 25 V99-211045
cllCapacitor, Metal Film, 0.22 pF, 100 V99-21 1037
clCapacitor, Metal Film, 0.022 iF, 100 V99211039
ci3apacitor, Metal Film, 0.22 uF, 100 V99-211037
cl4Capacitor, Ceramic, 1800 PF, 2 kV. Z5 V99-211040
cl?, Electrolytic, 470 pF, 25 V99-2 11044
cg, Electrolytic, 2200 pF, 16 V9-211048
20Electrolytic, 1000 iF, 25 V99-21 1047
C2, Ceramic, 470 PF, 1 kV, Z5P99-21 1D4S

D1, p2 D3 D4 D5-D7 Electrolytic, 2200 pF, 16 V lectrolytic, 1000 pF, 25 V Flectrolytic, 2200 pF, 16 V Diodes, Diode, Fast Recovery, RPG1OK Diode, Fast Recovery, RPG ISB. Diode, Fast Recovery, RPG 108 Diode, itching, IN4148 99211048 99-21 1047 9-2 11048

YO-2TLOLO YO-2ELWWEL 99-21 L009 99-2 L012

Page 42

Mlustraed Parts Lists

Hitron 5-Volt Power Supply Sub-Assembly Model HSA-122B(S) Parts List, Continued

Vincheators

Description

Do Dil, DIZ D13-D16

RI, RZ RB Ra RS

RO, RF RS RO RIO

Ri R12 R13 R14

R15 R16 RI7, R18 RID

R20 R21 R22 R23

R25 R20 R27 R31

ol

lox)

Fl Ic] SCRI TI

TRI VRI Zi Diode. Recovery, Diode. Schouky. S10SC Diode. Rectifier, IN4006

Inductors Inductor. 15 mi Inductor, ~ pht (Acceptable substitute is part no, 99-211051} Inductor, 2.2 pH Inductor, 1.5 mH

Resistors Resistor, Carbon Film, 180 k , #5%, 1 W Resistor, Wirewound, 120. + Resistor, Wirewound, 0.47. Resisior, Wirewound,

Resistor, Carbon Film, 5.6, £5%. 1/4 W Resistor, Wirewound. 0.47 2 Resistoz, Carbon Film, 10. , Resistor, Carbon Film, 1k, #

Resistor, Carbon Film, 47, Resistor, Carbon Film, 5.6 , Resistor, Carbon Film, 330 , Resistor, Carbon Film, 270 ,

Resistor, Carbon Film, 330 , V2 Resistor, Carbon Film, 8.2, £5%. 1/4 W Resistor, Carbon Film, 56 , 45%, 1/4 W Resistor, Carbon Film, 39 , £5%, 1/4 W

Resistor, Carbon Film, 2 k , #5%, 1/4 W Resistor, Carbon Film, 470 , +5%, 1/4 W Resistor, 2.2k , #2%, 1/4 W Resistor, Metal Film, 2k , #2%, 1/4 W

Resistor, Carbon Film, 10, +5%, 1/4 W Resistor, Wirewound, 50 Resistor, Carbon Film, 47, £5%, 1/4 W Resistor, Wizewound, 150 , #5%, 2. W

Transistors Transistor, NPN, 2SC1413A Transistor, NP: ‘Transistor, PNP, PI

Miscellaneous Fuse, 2 A, 250 V, SEMKO Regulator, LA43 AWC yristor, SCR ransformer

Thermistor, 0.5 Ohm, #5%, 5 W Potentiometer, Trimming, 3 kKOhm Diode, IN752A Fuse, 2 A, 250 ¥

Fuse Holde:. 6.35 mm ‘Terminal Block, 8 Ckt Heat Sink Heat Sink, 15 mm 99-211008

99-211052 99-211050 99-211054 99-241053

99-211034 99-211019 99-211018 99-211017

99-211027 99-211018 99-241029 99-211032

99-211025 99-211927 99-211026 99-211023

99-211022

99-211031 99-211030,

99-211035 9-211024 99-211021 99-211033

9 5 99-211025 99-211016

99-211002

99-211068 99-211057 99-211059 99-211061

5-10

Page 43

Vindicators Hhusteated Party Lists

N O T E S

Page 44

Hiustrated Paris Lists Vindicators

99-10140 Panel Assembly

75-9488, Locknut . a 99-10116

Tere Sy 99-10152 \ Right Conn Iniet 171006-035 Coin Mechanism 99-10147 Harness

75-9445 Locknut

99-10096 Fastener

99-10151 Left Coin Inlet

70-11-47 Lamp

99-10080 Lamp Socket

99-10105, 72-9406S Bar Screw

99-10104 Bar Retainer

99-10042 thru 99-10045 Corn Switch Assembly 99-10154 Bracket Assembly

99-10153 ; . a a . Coin Return Box ~~ 99-1015 ~ j Switch Cover 99-1068 ; Pm Sx Coin Chute ~ /

65-441C . K Coin Saatch A

99-10075 thru 99-10078 Switch Wires 99-10008, Retainer 7514128

Screw

Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

wy ns

Page 45

72-HA1404C Screw

99-10139 Coin Door

99-10148 Lock Assembly

Si a

72-JA1405B Screw

038091-01 ———

Coin Box Ilustrated Parts Lists

99-10148 Lock Assembly

99-10160 Cain Inlet Housing

ro

Spring

99-10141 Coin Return Cover

99-10117

= Coin Return Door

—— 99-10144 Channel! Clip

> 99-15066

Screw

99-10149 Service Door

ee 99-10143 Frame

NOTE

The acceptable substitute for this door (and the one used in games manufactured in Ireland) is the Coin Controls Ltd. Coin Door Assembly, part number 171034-001 You can obtain a free Coin Controls Ltd ' supplement (part. no. CO-305-01) that has illustrations and a parts list. Write to Atari Games Ireland Limited, Tipperary Town, ireland. Telephone 062-52155.

Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A

ye

Page 46

Miustened Ps

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No.

FHA

F2-JAL405B

75-9948, 99-10008

99-10042 99-1043 99-1044 99-10045

99-10068 99-10075 99-10076 99-10077

99-10078, 99-10080 99-10081 99-10096

99-10104 99-10105 99-10115, 99-10116

99-10117 99-10139 99-10140 99-10141

99-10143 99-10144 99-10147 99-10148,

99-10149 99-10150 99-10151 99-10152

99-10153 99-10154

99-10160 99-10161 99-15000 171006-035 ture Bayonet Lamp #440 8 3/S-Inch Truss-Head Screw F440 x W/4nch Pan-Head Screw

4-40 X .31-Inch Pan-Head Screw 4-40 x 3/4-Inch Pan-Head Screw 40 Locknut Retainer

Coin Switch Assembly for Belgian 5 Fr and U.S. 25¢ Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P

Coin Return Chute Switch Wire (included in coin ‘h assembly 99-10043) Switch Wire (included in coin switcl sembly 99-10042) Switch Wire (included in coin switch assembly 99-10044)

Switch Wire (included in coin switch assembly 99-10645) Lamp Socket Key Holder Fastener

Bar Retainer Bar Spring Plastic Coin Return Lever

Steel Coin Return Door Coin Door Coin Door Inner-Panel Assembly Die-Cast Coin Return Cover

Coin Door Frame Channel Clip Harness Lock Assembly

Service Door Switch Cover Left Coin Inlet Right Coin Inlet

Coin Return Box Bracket Assembly

1-Inch Wide Die-Cast Coin Inlet Hous: 25¢ Amber Side-Eniry Coin Button Assembly Screw for Clamp Metal Coin Mechanism for U.S.

Page 47

2y 23 22 420 19 48 47 WSs

Bd ap il BS Sse

0s Se ae, w= TF OSL CEE ys

g

A044402-21 A WO Hw Ie ie i? ie cla Te Vindicaiors

Figure 5-6 Vindicators Game PCB Assembly wig ti oe 7 eS

Te | + ¥ Ulustrated Parts Lists

Page 48

Mlustzited Parts Lists Vindicators,

Vindicators Game PCB Assembly Parts List

DesignatorDescriptionPart No.

Integrated Circuits 1/28 Integrated Circuit, 74LS244 4LS244 1c Iniegrated Circuit, 2804 A-45, 450 nsec 329-450

1DIntegrated Circuit,3,PRG O-H136059-1117
IrIntegrated CPRG 1-H136059-1119
1kIntegrated Circuit, EPROM, 27512-3, PRG 2-41136059-1121
1M, INIntegrated Circuit, RAM, 8KxS, 80 nsec (Acceptable substitutes137535-007
rexxx of equalor faster speed.)
2DIntegrated Circuit,EPROM, 27512-3, PRG 04.136059-1118
Integrated Ciscuit, EPROMPRG 1-L136059-1120
Integrated Circuit, EPROM,PRG 2-L136059-11

Integrated Circuit. RAM, SKx8. 80 nsec (Acceptable substitutes 137535-007 are part nos. 137535-xxx of equal or faster speed.)

3BIntegrated Circuit, 741824437-74LS244
3cIntegratedCircuit. PAL, 1618 A, Main Adr136059-1150
aD. 3EIntegrated Circuit, 741524437-7418244
3)Integrated Circuit, 74182;37-741 82:
3K, 3LIntegrated Circuit, 741837337-7418373,
3MIntegrated Circuit, 74L837437-74L5374
3NIntegrated Circuit, 7418138137177-001
4]Integrated Circuit, 741513937-7418139
4K, 4LIntegrated Circuit, 741824437-7418244
4MIntegrated Circuit, 74LS37437-74LS374
4NIntegrated Circuit, 74LS8637-T4LS86,
SDIntegrated Circuit, 68010137414-002
SFIntegrated Circuit, 748327-74S32

31, 5K, SL Integrated Circuit, 7418253, 3 5M Integrated Circuit, 7418374 4

5NIntegrated Circuit, 74LS17537-74LS175
OBIntegrated Circuit, 741824437-74L8244
6bIntegrated Circuit, 74180437-74LS04
OFIntegrated Circuit, 741817437-74LS174
6I, OK, OLIntegrated Circuit, 741825337-T4LS253
6MIntegrated Circuit, 741824437-FALS244
ONIntegrated Circuit, 741817437-74LS174
7/8BIntegrated Circuit, 7418138137177-001
7CIntegrated Circuit, 741824537-74LS245
7DIntegrated Circuit, 741S0237-T4LS02

JE Integrated Circvit, 7418244

7FIntegrated Circuit,Si75
7Integrated Circuit, 7418378137305-001
7KIntegrated Circuit, 741827337-74L8273
7h.Integrated Circuit, 7418378137305-001
7MIntegrated Circuit, 7415283137204-001
7NImegrated Circuit, PAL, 16R6 A, M.O-Control136059-1153

5-16

Page 49

Vindicators lustrated Parts Lists

Vindicators Game PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
7pIntegrated Circuit, EPROM, 2°, GRAF 1-2136059-11L15
7RIntegrated Circuit, EPROM, 27512-3, GRAF 1-0136059-1113,
8cIntegrated Circuit, 741524537-74LS245
8DIntegrated Circuit, 7419163 A37-741S163A
8EIntegrated Circuit, 741824437-7ALS244

8), 8K Integrated Circuit, 7418175, 8L, 8M Integrated Circuit, 7415273

8NIntegrated Circuit, 7415283137204-001
apIntegrated Circuit, ROM, GRAF 0-2136059-1103
8RIntegrated Circuit, ROM, GRAF 0-0136059-1101
OBIntegrated Circuit, 741$367 A37-741S367
OFIntegrated Circuit, 74LS11137149-001
orIntegrated Circuit, 825129, Programmed130059-1155,
9KIntegrated Circuit, 74LS169137109-001
OL, 9MIntegrated Circuit, 741827337-741S273
ONIntegrated Circuit, 74LS169137109-001
10/11P, 10/11RIntegrated Circuit, Slags137415-101
10J, 10KIntegrated Circuit, 74LS283137204-001
10L, 10MIntegrated Circuit, 74LS17537-7418175
10NIntegrated Circuit, 7415169137109-001
1FIntegrated Circuit, 74LS17537-74LS175
VLIntegrated Circuit, 7415163 A37-74LS163A
11MIntegrated Circuit, 74LS138137177-091
11NIntegrated Circuit, 825147, Programmed136959-1154
32FIntegrated Circuit, 741517437-74L8174
12LIntegrated Circuit, 741S25737-7415257
12MIntegrated Circuit, 7415378137305-001
12NIntegrated Circuit, 7418283137204-001

13F Integrated Circuit, 74LS32

  • Integrated Circuit, 7415253 BK Integrated Circuit, 74LS244 13L, Integrated Circuit, 74L$163 A

13M Integrated Circuit, 74LS174 . s

13NIntegrated Circuit, 74LS283,137204-001
13PIntegrated Circuit, ROM, GRAF 0-3136059-1104
13RIntegrated Circuit, ROM, GRAF 0-1136959-1 102

14/15B Integrated Circuit, SCOM 14D. Integrated Circuit, 1B 14F Integrated Circuit, 741832 14y Integrated Circuit, 741820

14K Integrated Circuit, 74152 14L, 14M Integrated C 14N Integrated

14PIntegrated Circuit, EPROM, 27512-3, GRAF 1-3130059-1 116
1ARIntegrated Circuit, EPROM, 275GRAF 1-1150059-1 114
(S/16NIntegrated Circuit,EPKOM, 2» Alpha130059-1123

y 7)

Page 50

Mlustrated Parts Lists

Vindicators Game PCB Assembly Parts List, Continued Vindicators

Designator Description

15F Integrated Circuit, 7 15y/e Integrated Circuit, GPC

I5L/MIntegrated Circuit, PRS137419-106
16K,Integrated Cire137533-004

are part no. 1

OL, 16MIntegrated Circuit,741524537-FALS245,
17DIntegrated Circuit, PAL, 1618 A, Priority436059-1151
VEIntegrated Circuit, PAL, 16L8 A, LB-Control136059-1152
WFO.Integraied Circuit, 7-37-74LS804
17L, 17MIntegrated Circuit37-74LS273
ASEIntegrated Circuit. 74L$7437-741874
18KIntegrated Cireu2Kx8, 70 nsec (Acceptable substitutes137533-004

are part nos. 13 Xx OF 137534-xxx of equal or faster speed.)

18LIntegrated Circuit, 74180837-74LS08
18MIntegrated Circuit137204-001
18NIntegrated Circuit,37-7ALS194
19KIntegrated Circuit, 7:37-74LS103A,
191, 19MIntegrated Circuit,137332-001

1OM/N 19N 20D, 20E

20F

24E

C1-C26, C36 C37-C40 C41, C43, C44

C46 cA cas, C49 C50 Integrated Circuit, 741874

» TALS32 ted Circuit, 74LS00

Integrated Circuit, 741832 Integrated Circuit, 7406 Integrated Circuit, 7415173 Integrated Circuit, 74LS08

Integrated Circuit, 741874 Integrated Circuit, 741510 Integrated Circuit, 74874 Integrated Circuit, 74L$197

Integrated Circuit, 7415158 Integrated Circuit, 741802 Integrated Circuit, 74804 Integrated Circuit, 741504

Integrated Circuit, 74.886 Capacitors Capacitor, .1 pF, 30 V, Ceramic Capacitor, 100 pF, 100 V, Ceramic Capacitor, 1 pF, 50 V, Ceramic Capacitor, 100 pF, 100 V, Ceramic Capacitor, 39 pl, 100 V, Ceramic F350 V. 00 -V, Ceramic Capacitor, .1 pF, 50 V, Ceramic

itor, 100 pF, 100 V, Ceramic pacitor, 478 pF, 50 V, Ceramic Capacitor, .001 pF, 50 V, Cer Capacitor, .1 pF, 59 V, Ce 37-74LS74 37-74LS 194 37-74LS32 37-74LS00

37-74LS32 37-7406 137529-001 37-74LS08

37-74LS74 37-T4LS10 37-74S74 137240-001

137203-001 37-741S02 37-74804 37-74LS04

37-74LS86

122002-104 122016-101 122002-104 122016-101

122016-390 122002-104 122016-101 122002-104

122016-191

122002-102 122002-104

Page 51

Vindicators Mlustrated Parts L

Vindicators Game PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
C1Capacitor, 10 pF, 25 V, Electrolytic24-250106

62, C63 Capacitor, .1 pF, 50 V, Ceramic 002-104

64Capacitor, 100 IF, 16 V, Electrolytic24-160107
€65-C149Capacitor, .1 pF, 50 V, Ceramic122002-104

Diodes

criDiode, MV5053, Light Emitting38-MV5053

Inductors

LiInductor, 100 pH41-3003
12-14Inductor, Ferrite Bead, N12N141003-005

Transistors

Q1, Q2Transistor, 2N390434-2N3904
@Transistor, 2N390633-2N3906
04,Transistor, 2N390434-2N3904
Q6Transistor, 2N390633-2N3906
Q7, Q8Transistor, 2N390434-2N3904
QoTransistor, 2N390633-2N3906
Q10‘Transistor, 2N390434-2N3904
Qu‘Transistor, 2N390633-2N3906
Q12Transistor, 2N390434-2N3904
QuTransistor, 2N5306133033-001
Qi4Integrated Circuit, LM317137233-001

Resistors

RLR8Resistor, 470 Ohm, #5%, 1/8 W110027-471
RO-R1SResistor, 1 K Ohm, #5%, 1/8 W110027-102

R16 Resistor, 470, #5%, 1/8 W R17 Resistor, 1 K Ohm, #5%, 1/8 W

RI8-R25Resistor, 470 Ohm, £5%, 1/8 W110027-471
R26-R33Resistor, 1 K Ohm, #5%, 1/8 W110027-102
R34-R4lResistor, 470 Ohm, #5%, 1/8 W110027-471
R42-R49, ROSResistor, 1 K Ohm,sw110027-102
RG4-ROTResistor, 470 Ohm, 25%, 1/8 W110027-471
RGB, R70-R74Resistor, | K Ohm, #5%, 1/8 W110027-102

R78 Resistor, 470 Ohm, #5%, 1/8 W

R80, R83-R85Resistor, | K Ohm, #5%, 1/8 W110027- 102
R86Resistor, 10 Ohm, £5%, 1/8 W110027-100
R87-ROOResistor, 1 K Ohm,#5%, 1/8 W’

ROI Resistor, 2.2 K Ohm, +5%, 1/8 W R92 Resistor, 4.7 K Ohm, #5%, 1/8 W

ROS Re 2.1 K Ohm, +5%, 1/8 W

R94Res, 120 Ohm, +vaw

ROS, Resistor, 620 Ohm,

ROGRe170 Ohm,

RO? . 3K Ohm, #5%

ROS10 K Ohm,#5%, L's W
ROD.Resistor, 470 Ohm, #5%,VS W

R100 Resistor, 4.7 K Ohm, £5%, 1 8 W

Page 52

Blustrated Parts Lists, Vindicators,

Vindicators Game PCB Assembly Parts List, Continued

Designator Description

R101 Resistor, 24 K Ohm, £5%, 1.8 W R102 . 120 Ohm, #5%, V8 W R103 Resistor, 620 Ohm, 25%, 1/8 W R104 Resistor. 470 Ohm, +5%, 1/8 W

R105 sistor, 3 K Ohm, +5%, 1/8 W" 110027-302 R106 sistor, 10 K Ohm, +5%, 1/8 W 110027-103

R107Resistor. 470 Ohm, +5%, 1/8 W110027-471
R108Resistor, 4.7 K Ohm, +5%, 1/8 'W110027-472

R109 24 K Ohm, 45%, 1/8 W 110027-242 R110 tor, 120 Ohm, 45%, 1/8 W 110027-121

R11Resistor, 620 Ohm, £5%, 1/8 W110027-621
R112Resistor, 470 Ohm, £5%, 1/8 W’110027-471
R113Resistor. 3 K Ohm, +5%, 1/8 W110027-302
R114Resistor, 10 K Ohm, +5%, 1/S W110027-103
RIMSResistor, 470 Ohm,Vvs3w110027-471
Ri16Resistor, 1 K Ohm,£5%, 1/8 W110027-102
R17Resistor, 470 Ohm,+5%, 1/8 W’110027-471
R118Resistor, 240 Ohm, +5%, 1/8 W110027-241
R119Resistor, 120 Ohm,+5%, 1/8 W110027-121
R120Resistor. 1 K Ohm, 45%, 1/8 W110027-102
Ri2lResistor, 240 Ohm, +5%, 1/8 W110027-241
R122Resistor, 330 Ohm, +5%, 1/8 W110027-331
R123,Resistor, 390 Ohm, +5%, 1/8 W110027-391
R124Resistor, 470 Ohm, 5%, 1/8 W110027-471
R125Resistor, 330 Ohm, 45%, 1/8 W110027-331
R126Resistor, 390 Ohm, +5%, 1/8 W110027-391
R17Resistor, 470 Ohm, +5%, 1/8 W110027-471
R128Resistor, 330 Ohm, +5%, 1/8 W110027-331
R129Resistor, 390 Ohm, +5%, 1/8 W110027-391
R130, R131Resistor, 470 Ohm, #5%, 1/8 W110027-471
R132Resistor, 68 Ohm,+5%, 1/4 W110000-680
R133Resistor, 470 Ohm, +5%, 1/8 W110027-471
R134Resistor, 1 K Ohm, +5%, 1/8 W110027-102
R135Resistor, 68 Ohm, £5%, 1/8 \"110027-680
R136Resiswor, 2.2 K Ohm, +5%, 1/8 W110027-222
R137Resistor, 240 Ohm, £5%, 1/8 W110027-241
R138, R139Resistor, 10 K Ohm, £5%, 1/8 W140027-103
R140Resistor, 68 Ohm,+5%, 1/4 W110000-680
R141%, 1/8 W110027-100
R142, R143Resistor, 68 Ohm, 5%, 1/4 ‘W110000-680
R144, R145,Resistor, 10 Ohm, £5%, 1/8 W110027-100
R147Resistor, 2.2 K Ohm, 5%, 1/5 W110027-222
R148-R150Resistor, 470 Ohm, +5%, 1/8 W110027-471
RiS1Resistor, 240 Ohm, +5%, 1/8 W110027-241

100 K Ohm, #5%, 1/5 W 110027-104 Resistor, 240 Ohm, 5%, 1/5 W 110027-241

R154, R155Resistor, 1 K Ohm, £5%, 1/8 W110027-102
R156Resistor,LS K Ohm, 5%, 1/8 W110027-182

5-20

Page 53

Vindicators

Vindicators Game PCB Assembly Parts List, Continued Mlustrated Parts Lists:

DesignatorDescriptionPart No.
R158Resistor, 1 K Ohm, +5%, 1/8 W110027-102
R160Resistor, 10 Ohm, +5%, 1/8 W110027-100

R161 Resistor, 1 K Ohm, #5%, 1/8 W

R162Resistor, 10 Ohm, 45%, 1/8 W110027-100
R163-R165Resistor, 1 K Ohm, +5%, 1/8 W110027-102
RP2Resistor, 470x7, +5%, 1/8 W, SIP (8-Pin)118007-471
RP3-RPGResistor, 4.7Kx9, +5%, 1/8 W, SIP (10-Pin)118010-472

Connectors

JSCMConnector, 11-Circuit, Header, .100" Ctr179118-011
RST, WDIS.Connector, 2-Circuit, Header, .100" Ctr179048-002
VIDConnector, 11-Circuit, Header, .100" Ctr179118-011
PLI-PL3Connector, 11-Circuit, Header, 100" Ctr179118-011
PPWRConnector, 12-Circuit, Hdr. .250" Ctr179069-012

Miscellaneous

XlCrystal, 14.318 MHz144000-004

Socket, 20-Pin 179259-020 Socket, 24-Pin Socket, 28-Pin

Socket, 40-Pin Socket, 64-Pin Test Point 179257-028

179257-040 179256-064 179051-001

Page 54

Vindicators Mlustrated Parts Lists

cur

ce a8 hw

10,250

R13 oT

Woo

g a 190

Oo 2.-Pa eT; ce 3 2K-ROM co 5 > a+ } 3

R7 - Ok cet TKTH case - § ete sU an ( usar Es cre sareos-003 = cee 5 BE . ( B pee fy v 2 B peas] a.

seoo.ew | ss00,250 Fs tN S 30 ry Lngee

4 | Is ssoe,250 | 3300.27 mtd + -/A+ = 5

ee

Lal 4 pv3 “8

agp utes t aut | Qt 4 4a

: Rap [ =e & a 7 3 a8 a® <=F se SF BE | re cr Cay A

_ 3 4 5 6

Figure 5-7 Stand-Alone Audio PCB Assembly A043713-23 A

Page 55

Vindicators,

Stand-Alone Audio PCB Assembly Parts List Ulustrated Parts Lists

LocationDescriptionPart No.

Integrated Circuits \-CPU ted Circuit, 6502 A 90-6013 1M-SCOM rated Circuit, SCOM 137526-001

2BIntegrated Circuit, LM32437-1M324
2DIntegrated Circuit, YM3012137402-001
2F-YAMIntegrated Circuit, YM2151137401-001
2H-RAMIntegrated Circuit,4-15, 150 nsec13744 1-002
2K-ROMIntegrated Circuit, 27512, 300 nsec136059-1124
2L-PALIntegrated Circuit, Programmed PALIGLS A, 25 ns136056-2101
3FIntegrated Circuit, 741537437-TALS374
3KIntegrated Circuit, Pokey137430-001
4A, 4BIntegrated Circuit, LM32437-1M324
4MIntegrated Circuit, 7418138,137177-001
SC, 5D, 5EIntegrated Circuit, 4066B37-4066
SF 5HIntegrated Circuit, 741827337-TALS273
5JIntegrated Circuit, 7415240137251-001
5KIntegrated Circuit, 74187437-741S74
6Integrated Circuit, 74LS39337-74LS393,
ALTCLKIntegrated Circuit, 741839337-T4LS393,

Capacitors

cLCapacitor, .22 pF, 50 V, Ceramic122015-224
C2Capacitor, 22 WF, 35 V, Electrolytic24-350226

C6-C9, C12 C13-C16 cl7

C18-C21 Capacitor, .22 pF, 50 V, Ceramic Capacitor, .1 uF, 50 V, Ceramic

r, 22 pF, 35 V, Electrolytic Capacitor, .1 iP, 50 V, Ceramic Capacitor, 100 pF. 100 V, Ceramic Capacitor, .1 pF, 50 V, Ceramic

Capacitor, 3300 pF, 25 V, Electrolytic, Radial Capacitor, .1 pF, $0 V, Ceramic Capacitor, 10 pF, 25 V, Electrolytic Capacitor, .22 pF, 50 V, Ceramic

Capacitor, .1 j1F, 50 V, Ceramic Capacitor, 10 WF, 25 V, Electrolytic Capacitor, .1 pF, 50 V, Ceramic acitor, .22 LF, 50 V, Ceramic

Capacitor. -1 pF, 50 V, Ceramic ipacitor, 10 pE, 25 V, Electrolytic acitor, .001 pF, 50 V, Ceramic “itor, .1 pF, 30 V, Ceramic 1p:

Capacitor, 047 pF, 100 V, Ceramic Capacitor, .1 pF, 50 V, Ceramic Capacitor, .001 pF, 50 V, Ceramic Capacitor, .1 uF, 50 V, Ceramic

25 V, Electrolytic 0 V, Ceramic 24-350226 122002-104

123003-338 122002-104 24-250106 122015-224

002-10

122015-473 122002-104 122002-102 002-104

250106 5-224

Page 56

Mlustrated Parts Lists. Vindieators

Stand-Alone Audio PCB Assembly Parts List, Continued

LocationDescriptionPart No.
c48-C52Capacitor, .1 pF, 50 V, Ceramic122002-104
C53Capacitor, .0022 pF, 50 V. Axial Ceramic122015-2.
C54Capacitor, .0027 pF, 50 V, Ceramic122015:
ossCapacitor, .001 pF, 50 V, Ceramic122002-102
56Capacitor, .0027 pF, 50 V, Ceramic122015-272
C57Capacitor, .001 pF, 50 V, Ceramic122002-102
C58Capacitor, .0022 pF, 50 V, Axial Ceramic122015-222
C61-C68Capacitor, .1 pF, 50 V, Ceramic122002-104
CodCapacitor, 39 pF, 100 V, Ceramic.122016-390
C70Capacitor, 190 pF, 100 V, Ceramic122016-101
71-C74, C84Capacitor, .1 pF, 50 V, Ceramic122002-104

Diodes CR1, CR2 Diode, 1N4001 CR3 Diode, MV5053, Light-Emitting cR4, CRS Diode, 1N4003 CRE Diode, MV5053, Light-Emitting

CR7-CR1O Diode, 1N5401 R13 Diode, MV5053, Light-Emitting

CR14, CRIS.Diode, 1N400131-1N4001

Inductor

ulInductor, 100 pH41-3003

Transistors

QI, @Integrated Circuit, TDA2030137301-001
Q4Integrated Circuit, 7905, Standup37-7905
Q5-Q8Transistor, 2N390434-2N3904
Q9, Q10Transistor, 2N5306133033-001

Resistors

RIResistor, 1 K Ohm, +5%, 1/4 W110000-102
R2Resistor, 10 K Ohm, #5%, 1/4 W110000-103
R3, R4Resistor, 1 Ohm , +5%, 1/4 W110000-010
RSResistor, 1 K Ohm, #5%, 1/4 W110000-102
RGResistor, 10 K Ohm, +5%, 1/4 W110000-103
R10Resistor, 0 Ohm, 1/4 W110005-001
RiResistor, 1 K Ohm, £5%, 1/4 W110000-102
Ri2Resistor, 470 Ohm, +5%, 1/4 W110000-471
R13Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R14Resistor, 470 Ohm, +5%, 1/4 W110000-471
RISResistor, | K Ohm, £5%, 1/4 W.110000-102
RIGResistor, 470 Ohm, +5%, 1/4 W110000-471
R17, R18Resistor, 10 K Ohm, +5%, 1/4 W110000-103,
RIDResistor, 22 K Ohm, +5%, 1/4 W110000-223,
R20Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R21Resistor, 22 K Ohm, +5%, 1/4 ‘W110000-223
R22Resistor, 10 Ohm, +5%, 1/4 W110000-100

R23 560 Ohm, +5%, 1/4 W 110000-561

R24Resistor, 1 K Ohm, £5%, 1/4 W110000-102
R26, R27Resistor, 10 Ohm, #5%, 1/4 W110000-100
Page 57

Vindicators

Stand-Alone Audio PCB Assembly Parts List, Continued Mlustrated Parts Lists

LocationDescriptionPart No.
R28Resistor, 10 K Ohm, +5%, 1/4 W110000-103
R29Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R33, R34Resistor, 470 Ohm, +5%, 1/4 W110000-471
R35Resistor, 75 K Ohm, +5%, 1/4 W110000-753

R36, R37 Resistor, 10 K Ohm, +5%, 1/4 W 238 Resistor, 47 K Ohm, +5%, 1/4 W R43-R48. Resistor, 12 K Ohm, #5%, 1/4 W R49 Resistor, 10 K Ohm, +5%, 1/4 W

R50Resistor, 1 K Ohm,+5%, 1/4 W110000-102
R51, R52Resistor, 10 K Ohm, +5%, 1/4 W110000-103
R53, R54Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R55, R56Resistor, 150 K Ohm, +5%, 1/4 W410000-154
R58Resistor, 1 K Ohm, #5%, 1/4 W110000-102
R59Resistor, 150 K Ohm,+5%, 1/4 W110000-154
ROOResistor, 1 K Ohm, #5%, 1/4 W110000-102
R61Potentiometer, 10 K Ohm, Horiz., Dual119011-103
ROResistor, 7.5 K Ohm, 45%, 1/4 W110000-752
ROBResistor, 30 K Ohm, £5%, 1/4 W110000-303,
G4Resistor, 15 K Ohm, +5%, 1/4 W110000-153
RO, ROResistor, 12 K Ohm, +5%, 1/4 W110000-123
RO?Resistor, 15 K Ohm, +5%, 1/4 W110000-153
ROS.Resistor, 30 K Ohm, +5%, 1/4 W110000-303
RODResistor, 7.5 K Ohm, +5%, 1/4 W110000-7
R70Resistor, 75 K Ohm, +5%, 1/4 W110000-753
R71Resistor, 150 K Ohm, +5%, 1/4 W110000-154
R74-RB1Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R82Resistor, 470 Ohm, +5%, 1/4 W110000-471
R83.Resistor, 150 K Ohm, 45%, 1/4 W110000-154
R84Resistor, 0 Ohm, 1/4 W110005-001

R85A Resistor, 470 Ohm, +5%, 1/4 W

R86Resistor, 220 Ohm, +5%, 1/4 W110000-221
R103Resisior, 150 K Ohm, +5%, 1/4 W110000-154

Connectors

JACDCTConnector, 12 Circuit, Header, .156 Cur, Key 11179213-012
JCDLConnector, 2 Circuit, Header, .156 Cir179213-002
JCOINConnector, 6 Circuit, Header, .100 Ctr, Key 2179118-006
JSCOMConnector, 11 Circuit, Header, .100 Ct, Key 5179118-011
JSPKConnector, 6 Circuit, Header, 156 Ctr, Key 3179213-006

Miscellaneous

sW1Switch, Slide, SPDT69-004
A-CPUSocket, 40 Pin79-42C40

2D Socket, 16 Pin 2F-YAM Socket, 24 Pin 2H-RAM, 2K-ROM Socket, 28 Pin 3K Socket, 40 Pin

Test Point 179051-001

HSL, HSRHeat Sink, TDA2030178190-032
Q2Nu Washer Assy, 6-3275-99516
QPan Head Screw, #6-3272-16068

uw a

Page 58

HMlustrated Ports iists

N Vindicators

S

Page 59

Left Coins

Right Coins 0 Plyr Mins 1 Plyr Mins 2 Plyr Mins Easy Games Medium Games

Hard Games

Joined Games Total Games

Error Count

Total Coins

Avg Time/Coin** Vindicators™

Date__

Coin Information and Game Statistics

Number of coins deposited in left coin mechanism. Number of coins deposited in right coin mechanism Minutes of idle time

Minutes played as a 1-player game Minutes played as a 2-player game Number of players who started at the easy level Number of players who started at the medium level Number of players who started at the hard level Number of players who joined while a game was in progress Total number of unique games played* EEROM errors

Total number of coins deposited in both coin mechanisms Average game time per coin in seconds (including add-a-coin continuation games)

Histogram Information

Length of Game in Seconds Number of Games Length of Game in Seconds Number of Games 9-59 330-359 60-89 360-389

90-119 390-419 7 120-149 420-449

150-179 450-479

180-209 480-509 210-239 —_ 510-539 240-269 540-569

270-299 570-599 300-329 600 & Up

*One "game" is the time between a player starting and that player dying. regardless of time, number of coins inserted, or how many have plaved Vindicators. “It is important to note that “Aug Time/Gour” is in seconds, ancl this number cannot simply be doubled to compute Avg. Time/Game for a 2-credit-start, 1-credil-io-continue game (manufac er's recommended setting), At this setting, the following formula can be used to calculdte average seconds per game or average playtime in seconds: Total coins = total games = X X-1.00= ¥ Xx aug. Time/Coin = Z Z* Y= Avg. Seconds per Game

yt Ww a

Page 60

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 61

AC Alternating current, from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.

ACTIVE STATE The true state of a signal. For example: The active state for is low. ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off), Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter.

BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (and 1) BIT A binary digit; expre: ec as 1 or 0. BLANKING Turning off the beam on a cathode-ray iube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode.

cHIP An integrated circuit comprising many Circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A G-digit electromechanical device that counts the coins inserted in the coin mechanisnxs).

  • COIN MECHANISM ‘A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted,

COMPLEMENTARY Having Opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into 4 single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry,

Glossary

COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.

CREDIT One play for one person based on the game switch settings.

CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing, DARLINGTON A two-transistor amplifier that provides extremely high gain.

DC Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses. the microprocessor logic. DMA is normaily used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning of not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage.

gh

Page 62

FLYBACK A step-up tansformer used ina display to provide the high voltage. GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A cireuit in which one signal switches another signal on and off.
  • To control the pa: sage of a pulse

A prefabricated assembly of insulated Wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used.

IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output TRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may Or may not respond. LED ‘The abbreviation for a light-emitting diode.

LOCKOUT COIL Directs coins into the coin return box when there is no power to the game.

LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one high-speed data stream for simultane- ‘ous transmission on a single line. NMI Non-anaskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interupt request

PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discreie blocks of data. Thes blocks are called page: ich bloc! X mumber of bytes PCB The abbreviation for a printed-circuit board.

PHOTOTRANSISTOR A wansistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chieily as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data.

RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathoderay tube horizontally and vertically with an electron beam. Tne display system controls the intensity of the electron beam,

RETRACE. In a raster-scan display, retrace is the time during which the cathode-ray tbe electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data

SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located.

TROUBLESHOOT The process of locating and repairing a fault.

VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube,

WATCHDOG A counter circuit designed to protect the microprocessor

from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, Which causes the microprocessor to keep resetting X-Y DISPLAY A display system whereby images are displayed with vectors ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 63

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided: :

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller's plant; and (©) Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 64

ATARI

GAMES

Atari Games Corporation

~675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035