CATHODE RAY TOMES

Pac-Man Plus Conversion Kit from Pac-Man or MsPac-Man (M051-00338-A004)

Pac-Man Plus (Namco (Midway license), 1982) · Manual · 20 pages · 25 sections · original scan

Page 1

PAC-MAN/MS. PAC-MAN T

PAC-MAN

PLUS) |

CONVERSION

FOR

UPRIGHT — COCKTAIL TABLE — MINI

MODELS

PART NO. M051-00338-A004

Page 2

Conversion Kit Components

Enclosed is a PAC-MAN PLUS Conversion Kit for your PAC-MAN/MS. PAC-MAN game. It includes the following items by model: ALL MODELS:

AUXILIARY GAME LOGIC BOARD WITH RIBBON CABLE (POTTED) AUXILIARY GAME LOGIC BOARD SUPPORT BRACKET (FOR PAC-MAN CONVERSIONS ONLY) AUXILIARY GAME LOGIC BOARD SUPPORT BRACKET MOUNTING SCREWS (FOR PAC-MAN CONVERSIONS ONLY) PLASTIC MOUNTING STAND-OFFS FOR THE AUXILIARY GAME LOGIC BOARD (FOR PAC-MAN CONVERSIONS ONLY) INTEGRATED CIRCUIT FOR POSITION “5 E” ON MAIN GAME LOGIC BOARD INTEGRATED CIRCUIT FOR POSITION “5 F” ON MAIN GAME LOGIC BOARD INTEGRATED CIRCUIT FOR POSITION “4 A” ON MAIN GAME LOGIC BOARD INTEGRATED CIRCUIT FOR POSITION “6 E” ON MAIN GAME LOGIC BOARD INTEGRATED CIRCUIT FOR POSITION “6 F” ON MAIN GAME LOGIC BOARD INTEGRATED CIRCUIT FOR POSITION “6 H” ON MAIN GAME LOGIC BOARD INTEGRATED CIRCUIT FOR POSITION “6 J” ON MAIN GAME LOGIC BOARD INTEGRATED CIRCUIT FOR POSITION “7 F” ON MAIN GAME LOGIC BOARD MS. PAC-MAN PARTS AND OPERATING MANUAL BR yaw

Bean annnannn

UPRIGHT MODEL:

1 ATTRACTION PANEL 1 SERIAL NUMBER TAG 1 MAIN-DISPLAY-GLASS LABEL

MINI MODEL:

1 ATTRACTION PANEL SERIAL NUMBER TAG MAIN-DISPLAY-GLASS LABEL

COCKTAIL TABLE MODEL:

TABLE TOP GLASS UNDERLAY 2 TABLE TOP GLASS LABELS (FOR PAC-MAN CONVERSIONS ONLY) SERIAL NUMBER TAG =

Page 3

PAC-MAN to

PAC-MAN PLUS Conversion Procedure

To convert your PAC-MAN game to a PAC-MAN PLUS game is a fairly simple operation. Just follow the Steps below and the illustrations given in each Figure,

1 Turn the power off to your game and dis- CAUTION:

re The right hand laich is very close to the HIGH VOLTAGE on the monitor.

2 Opening the Cabinet: O Once the latches are released, unhook them

from their latch plates. O UPRIGHT and MINI models: © Grasp the table top at “A” and open it as Unlock and open the rear access door. indicated in Figure 1.

0 COCKTAIL TABLE model: CAUTION: Due to the weight of the monitor, Open the coin box door and release the two EXTREME CARE MUST be taken when opening latches indicated in Figure 1. the cabinet.

CLAMPS

Page 4

3 Main Game Logic Board removal: 0 Remove the P.C.B. clamps indicated in Figure 3 D Disconnect the Main Game Logic Board from all and slide the Main Game Logic Board out of the its cabling. See Figure 2. cabinet.

DISCONNECT CABLING

FILTER BOARD a A ‘ FILTER BOARD (SERVICE OPTION) ; a” es ae ‘ (SERVICE OPTION)

DISCONNECT _— — . DISCONNECT CABLING

COCKTAIL

Page 5

REMOVE CLAMP TO SLIDE P.C.B. CLAMP TO

P.C.B. OUT REMOVE

SLIDE

  • CLAMPS. TO SLIDE P.C.B. OUT REMOVE

UPRIGHT

= x“ o

Page 6

4 Install the Auxiliary Game Logic Board

Support Bracket as indicated in Figure 4, C Install the four plastic mounting stand-offs to the Auxiliary Game Logic Board Support Bracket.

POSITION BRKT. IN THIS AREA AND SCREW INTO SIDE OF CABINET WITH 2 SCREWS

INSERT STANDOFFS AS SHOWN (4) INSERT STANDOFFS AS SHOWN (4)

POSITION BRKT. IN THIS AREA AND SCREW INTO SIDE OF CABINET WITH 2 SCREWS

INSERT STANDOFFS AS SHOWN (4)

Page 7

Cut the plastic securing strap and remove the “PIGGY-BACK” module indicated in Figure 5 IF YOUR GAME IS EQUIPPED WITH ONE. If it IS NOT equipped with one, simply proceed to Step 6 below.

CUT PLASTIC STRAP AND LIFT SMALL P.C.B. (PIGGY BACK) OFF OF MAIN BOARD

6 Remove the Z-80 CPU from the Main Game

Logic Board as shown in Figure 6. BE CARE- FUL NOT TO BEND ITS PINS!! Return this CPU to your stock. It may be used as a spare part.

Page 8

7 Remove the six EPROMS and 2 PROMS

located as shown in Figure 8 and set them aside. BE CAREFUL NOT TO BEND THEIR PINS! Replace the removed EPROMS and PROMS with the ones supplied in your conversion kit. They are installed as shown in the above Figure.

REMOVE (6) EPROMS AND REINSERT NEW EPROMS SUPPLIED WITH KIT. (LOCATIONS 5E, 5F, 6E, 6F, 6H & 6J)

IMPORTANT!
NOTE LOCATION OF NOTCH ON ALL I.C.s REMOVED BEFORE INSERTING REMOVE (2) PROMS AND REINSERT NEW PROMS SUPPLIED WITH KIT. (LOCATIONS 4A & 7F)
Page 9

Plug the ribbon extension cable for the Auxiliary Game Logic Board into the empty socket on the Main Game Logic Board that was left when you removed the Z-80 CPU from it in Step 6. See Figure 8.

INSERT RIBBON CABLE INTO SOCKET AS SHOWN

9 If your game was equipped with a “PIGGY- BACK” module that you removed in Step 5, reinstall it at this time. See Figure 9. lf it was not equipped with one, simply proceed to Step 10.

REINSTALL “PIGGYBACK” MODULE TO MAIN P.C.B.

NOTE LOCATION OF NOTICES IN I.C.’s
Page 10

10 Reinstall the Main Game Logic Board

and the Auxiliary Game Logic Board (now attached to it by the ribbon cable) back into the game cabinet.

ll Install the Auxiliary Game Logic Board

to the four plastic snap-in mounting stand-offs of the Auxiliary Game Logic Board Support Bracket as shown in Figure 10.

PUSH AUXILIARY P.C.B. ONTO STANDOFFS AS SHOWN PUSH AUXILIARY P.C.B. ONTO STANDOFFS AS SHOWN

Page 11
NOTE: DO NOT FORGET to SAVE the six EPROMS and two PROMS you removed in Step 7 of this procedure. Put them in the packaging that the new EPROMS and PROMS came in and store them in a dark place at room temperature. They will not be harmed if stored this way. Thus, by reversing this procedure, you could convert your game back toa PAC-MAN model if you ever wanted to. Reconnect all previously removed cabling to the Main Game Logic Board. Close and lock the game cabinet and plug it back into its wall outlet. Turn the game on and let it warm up for a few minutes, run a Self-Test on it, and play a couple of games to be sure everything is working properly.

Installation of Remainder of Conversion Kit Parts

  • ATTRACTION PANELS (UPRIGHT AND MINI MODELS): ¢ Turn the power off to the game. ¢ Remove the screws installed in the top attraction panel bracket. © Lift off the bracket. © Slide the attraction panel up and out. Install the new PAC-MAN PLUS attraction 3. MAIN-DISPLAY-GLASS panel and secure it with the top attraction (UPRIGHT AND MINI MODELS): Panel bracket. © Turn the power off to the game.
  • TABLE TOP GLASS AND UNDERLAY e@ Remove the main-display-glass as described (COCKTAIL TABLE MODEL): in the appropriate sections of your OPERA- ¢ Reinstall the table top glass. ¢ Secure the above with the table top glass clamps and screws you removed earlier. ¢ Affix BOTH Table Top Glass Labels to the TOP SIDE of the table top glass as shown in Figure 11.

Turn the power off to the game. Remove the Screws securing the table top glass clamps in place. Remove the above clamps and the table top glass. Affix the new PAC-MAN PLUS Serial Number Tag to the UNDERSIDE of the table top glass as shown in Figure 11.

TABLE TOP GLASS LABELS

SERIAL NUMBER TAG TOR’S MANUAL. Affix the new PAC-MAN PLUS Serial Number Tag to the UNDERSIDE of the main-displayglass as shown in Figure 12. Reinstall the main-display-glass. Aifix the Main-Display-Glass Label to the TOP SIDE of the main-display-glass as shown in Figure 12.

MAIN DISPLAY GLASS LABEL

SERIAL NUMBER TAG

Page 12

a:

Page 13

MS. PAC-MAN to PAC-MAN PLUS Conversion Procedure

To convert your MS. PAC-MAN game to a PAC-MAN PLUS game is a fairly simple operation. Just follow the Steps below and the illustrations given in each Figure.

1 Turn the power off to your game and disconnect it from its wall outlet.

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor.

2 Opening the Cabinet: O Once the latches are released, unhook them

from their latch plates. O UPRIGHT and MINI models: O Grasp the table top at “A” and open it as Unlock and open the rear access door. indicated in Figure 1.

0 COCKTAIL TABLE model: CAUTION: Due to the weight of the monitor, Open the coin box door and release the two EXTREME CARE MUST be taken when opening latches indicated in Figure 1. the cabinet.

CLAMPS

Page 14

3 Main Game Logic Board removal:

Q Disconnect the Main Game Logic Board from all its cabling. See Figure 2. © Remove the ribbon extension cable from the C Cut the plastic securing strap and remove the Main Game Logic Board. “PIGGY-BACK” module indicated in Figure 2 IF CG Remove the P.C.B. clamps indicated in Figure 3 YOUR GAME IS EQUIPPED WITH ONE and set and slide the Main Game Logic Board out of the it aside. cabinet.

REMOVE “PIGGY-BACK” i ee DISCONNECT MODULE AND E j 3 i CABLING RIBBON CABLE y - e- 4

MAIN LOGIC BOARD

REMOVE “PIGGY-BACK” 7 : REMOVE “PIGGY-BACK” MODULE AND : - : MODULE AND RIBBON CABLE S 4 RIBBON CABLE FROM FROM MAIN LOGIC BOARD MAIN LOGIC BOARD

  • DISCONNECT _. CABLING
Page 15

REMOVE CLAMP TO SLIDE P.C.B. OUT

REMOVE (2) CLAMPS : : _ _— REMOVE CLAMP

TO SLIDE q TO SLIDE P.C.B. OUT

COCKTAIL

Page 16

4 Remove the six EPROMS and 2 PROMS

located as shown in Figure 4 and set them aside. BE CAREFUL NOT TO BEND THEIR PINS! Replace the removed EPROMS and PROMS with the ones supplied in your conversion kit. They are installed as shown in the above Figure.

REMOVE (6) EPROMS AND REINSERT NEW EPROMS SUPPLIED WITH KIT. (LOCATIONS 5E, 5F, 6E, 6F, 6H & 6J)

IMPORTANT! REMOVE (2) PROMS

NOTE LOCATION AND REINSERT NEW OF NOTCH ON PROMS SUPPLIED ALL I.C.s REMOVED WITH KIT. BEFORE INSERTING (LOCATIONS 4A & 7F)
Page 17

5 Plug the ribbon extension cable for the new

Auxiliary Game Logic Board into the empty socket on the Main Game Logic Board that was left when you removed the original ribbon cable in Step

  • See Figure 5.

INSERT RIBBON CABLE INTO SOCKET AS SHOWN

If your game was equipped with a “PIGGY- BACK” module that you removed in Step 3, reinstall it at this time. See Figure 6. If it was not equipped with one, simply proceed to Step 7.

REINSTALL “PIGGYBACK” MODULE TO MAIN P.C.B.

NOTE LOCATION OF NOTCHES IN I.C.’s
Page 18

7 Remove the Auxiliary Game Logic Board

from its support posts and return it to your stock for possible future use. See Figure 7.

REMOVE AUXILIARY GAME LOGIC BOARD FROM REMOVE AUXILIARY GAME LOGIC BOARD FROM POSTS

Page 19

8 Reinstall the Main Game Logic Board and 9 Install the new Auxiliary Game Logic Board the new Auxiliary Game Logic Board (now to the four plastic snap-in mounting standattached to it by the ribbon cable) back into the offs of the Auxiliary Game Logic Board Support game cabinet. Bracket as shown in Figure 8.

PUSH AUXILIARY P.C.B. ONTO STANDOFFS AS SHOWN PUSH AUXILIARY P.C.B. ONTO STANDOFFS AS SHOWN

COCKTAIL

Page 20

10 Reconnect all previously removed cabling 11 Close and lock the game cabinet and 12 Turn the game on and let it warm up for

to the Main Game Logic Board.

plug it back into its wall outiet.

a few minutes, run a Self-Test on it, and play a couple of games to be sure everything is working properiy.

NOTE: DO NOT FORGET to SAVE the Auxiliary Game Logic Board, six EPROMS, and two PROMS you removed in Steps 3 & 4 of this procedure. Put them in tne packaging that the new EPROMS and PROMS came in and store them in a dark place at room temperature. They will not be harmed if stored this way. Thus, by reversing this procedure, you could convert your game back to a MS. PAC-MAN model if youever wanted to.

Installation of Remainder of Conversion Kit Parts

  • ATTRACTION PANELS (UPRIGHT AND MIN! MODELS): © Turn the power off to the game. e Remove the screws installed in the top attraction panel bracket. e Lift off the bracket. ¢ Slide the attraction panel up and out.
  • Install the new PAC-MAN PLUS attraction panel and secure it with the top attraction panel bracket.
  • TABLE TOP GLASS AND UNDERLAY (COCKTAIL TABLE MODEL): ¢ Turn the power off to the game. e Remove the Screws securing the table top glass clamps in place. « Remove the above clamps and the table top glass. © Affix the new PAC-MAN PLUS Serial Number Tag to the UNDERSIDE of the table top glass as shown in Figure 9.

TABLE TOP GLASS LABELS

SERIAL NUMBER TAG ¢ Reinstall the table top glass. e Secure the above with the table top glass clamps and screws you removed earlier. ¢ Affix BOTH Table Top Glass Labels to the TOP SIDE of the table top glass as shown in Figure 9.

  • MAIN-DISPLAY-GLASS (UPRIGHT AND MIN! MODELS): © Turn the power off to the game. *# Remove the main-display-glass as described in the appropriate sections of your OPERA- TOR'S MANUAL. e Affix the new PAC-MAN PLUS Serial Number Tag to the UNDERSIDE of the main-displayglass as shown in Figure 10. © Reinstall the main-display-glass. e Affix the Main-Display-Glass Label to the TOP SIDE of the main-display-glass as shown in Figure 10.

MAIN DISPLAY GLASS LABEL

SERIAL NUMBER TAG