CATHODE RAY TOMES

Road Blasters CO-298-01 1st Printing Steering

Road Blasters (upright, rev 4) (Atari Games, 1987) · Change Order · 4 pages · 6 sections · original scan

Page 1

Road Blasters /System I’ RTC Steering Control:

Assembly and Maintenance Procedures

Introduction

This Road Blasters game uses a specially designed RTC (returnto-center) steering control assembly, Atari part number A044397-01. This supplement contains the assembly and. maintenance procedures and drawing for this control. This information replaces pages 3-4 through 3-6 and Installing the Harness Assembly on page 3-7 in your Road Blasters/System I Operators Manual (TM-304). Please keep this supplement with your manual for reference.

NOTE Certain maintenance procedures can be performed with the RTC steering control attached to the control panel. However, for convenience and to avoid damaging the control panel, we recommend that the control be removed from the control panel before any maintenance or repair is performed.

Preventive Maintenance

Preventive maintenance on the RTC steering control consists of: © Inspecting the RTC steering control housing for excessive ‘wear or dirt. ©. Checking the operation of all four handle switches. Inspecting the Optical Coupler PCB Assembly for damage and contamination. Lubricating the bronze bearings attached to the control base weldment. Replacing or tightening the securing hardware if necessary. (See Screw Torque Specifications Table.) Perform the following procedure to lubricate and tighten the RTC steering control. (See Figure 1.)

  • Remove the control panel. (Refer to Chapter 3 in the Operators Manual.)
  • Apply a film of light oil (Atari part no. 107013-001) to the inside and top surfaces of both bronze bearings attached to the inside ends of the control base weldment.
  • Use a %<inch wrench to tighten the nuts holding the RTC steering control to the control panel.

Corrective Maintenance

The following corrective maintenance procedures apply to the RTC steering control. The RTC steering control consists of the handle assembly and the steering assembly. Removing the Handles Perform the following procedure to remove the handles from the handle assembly. 1, Use a 3 mm hex driver to remove the two cap screws holding the cover on each handle.

  • Unsolder the three harness wires from both Switch PCBs inside each handle.
  • Use a 9/64-inch hex driver to loosen and remove the two cap screws that secure the brace and cover.
  • Cut the tie wrap holding the harness, then gently pull the harness out of the shaft.
  • Usea ¥,-inch hex driver and a %,-inch wrench to remove the two cap screws that hold each handle shaft to the steering head.
  • Gently slide the handles from the shaft.
  • Reassemble the handle in the reverse order of removal.

Disassembling the Steering Assembly

Perform the following procedure to disassemble the steering assembly. 1, Remove the handle covers as described previously.

  • Unsolder the three harness wires from the handle pushbutton and trigger switches.
  • Remove the green ground wire from the ground clip on the base, and the Optical Coupler PCB harness connector.
  • Use a hex driver to remove the two screws holding the Optical Coupler PCB Assembly to the base.
  • Use a 3/32-inch hex driver to remove the cap screw holding the encoder disc. Remove the retaining ring, two washers, encoder disc, encoder spacer, and small gear.

A WARNING A Shield your face and eyes when prying the retainer from the shaft because the retainer can fly loose at a high speed. Cover the retainer with a rag or any material that can trap the retainer.

Screw Torque Specifications Table

s Seating Torque Ref. No. Screw Size Inch-Lbs.

0}2-56541
®4-401243
@6322845
®8-323245
®10-326445
©M4-182845
@%4-207545

§

F

Page 2

177010-244 NOTE Nyloc Nut The numbers in circles refer to the reference 96-01 Latte in the Screw Torque Specifications Steering Head Weldment 02 (Part of the 044398-01 Weldment) 178209 72-8010 75-07010 Handle Cover (Left Blue) @ Spee atts Ave SocketHd.-Cap Screw ©

044399-02 #10 Flat Washer Weldment (Left) 177010-241 Nyloc Hex Nut 178210-001 Button 175002.004 040240-01 Bumper

oa 178210-002 Button Joint

160035-001 ‘Switch

. 172012-2818 Socket-Hd-Cap Black Screw @ 044000-01 Handle Modification (Right) 176035-1820 Cover Socket-Hd.-Cap Screw @ Weldment (Right) Handle Cover (Right Blue)

Figure 1 Disassembly and Lubrication

6.Use a 7/64-inch hex driver to remove the cap screw hold-12.Usea5/32-inch hex driver and %inch combination wrench

ing the large spur gear and hub to the shaft. to remove the two bumpers from the frame.

  • Use a slotted screwdriver (or an appropriate tool) to remove the retainer from the shaft.
  • Use a %<inch wrench to remove the anchor nut on the end N of the anchor pin. (The anchor nut holds the hook ends of With the steering control disassembled, lubricate the bronze bearing surfaces, and the torsion springs. Also, i the torsion-steering springs. i : rings.) apply penetrating adhesive inside the anchor nut hole
9.Use a 9/64-inch hex driver to remove the two screws hold- -after assembly. Refer to Preventive Maintenance for

ing the cover to the steering head. further information. { 10. Cut the tie wrap holding the harness, then gently pull the | harness out of the shaft.

11.Gently pull the steering assembly from the handle assem-13.Reassemble the steering assembly in the reverse order of

bly. Make sure the harness wires are free to slide out of the removal. Be sure that all necessary screws have been tighthandle-assembly shaft. ened according to the Screw Torque Specifications Table.

Page 3

040235-01 ‘Spur Gear with Hub A043042-01 175002-001 Washer

178012-001 .750 Diameter Retaining Ring

£107013-001 Lubricant 406007001 Penetrating Adhesive 040237-01 72-8406 Anchor Nut Screw @

4 178027-001 ds Lubricant SF] 040239-01 Pst : 75-0148

< 178101-002 043928-01 . Spur Gear Base 5 044023-02 or -01 => Spacer sR

& Jer Disc Stop Bumper e. p 24 ‘s, ) oy Na’ Encoder Shaft 040241-01 Wate hesecioy Spacer Bearing \ ox @® 4 ) : 72-CT604 DS. IN 1 i y Screw @ p eo OS 4 A043937-01 KO Coupler PCB Assy

178118-001 Sleeve Bearing

178097-001 Bearing with Washer/Nut 040240-0' ‘Stop Bumper 040238-01 177010-241 475009-170 Anchor Pin © Hex Nut 178012-003 %. Diameter Retaining Ring Washer

Figure 1 Disassembly and Lubrication, Continued

Installing the Harness Assembly Perform the following procedure to install the harness assembly switches should be as shown in Figure 2. to the RTC steering control. ° 3, Route and solder the wires to the switches. Note that either 1, If necessary, remove the handle covers as described under wire bundle can go to either handle. Removing the Handles. 4, Install the wire tie, optical coupler PCB connector, and the

  • Guide the harness wires into the spur-gear end of the hollow ground clip. Make sure the wires do not interfere with the steering-assembly shaft. The wire routing on both micro- gears when the steering control is mounted.
Page 4

Figure 2 Wire Routing on Handle Switches

For technical assistance, call Atari Customer Service at (408) 434-3950 (Monday-Friday, 7:30 am-4:00 pm Pacific time)

Atari Games Corporation ¢ 737 Sycamore Drive * P.O. Box 361110.¢ Milpitas, CA 95035 Eke Eiichi nai Alibi si