CATHODE RAY TOMES

Crystal Castles TM-266 1st Printing Missile Command Conversion

Crystal Castles (version 4) (Atari, 1983) · Technical Manual · 26 pages · 18 sections · original scan

Page 1

TM-266 ‘at printing

Conversion Instructions

for

Missile Command”

to

Crystal Castles”

Page 2

Atari Customer Service

Ifreading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at one of these Atari Customer Service offices:

UNITED STATES Parts and Service

Atari, Inc. California Customer Service Office

PO, Box 906 Milpitas, CA 95035 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Paci ic Time) | *ywhere in the US. including Alaska and awail (408) 943-1120

EUROPE Parts and Service

Atari Leland Limited European Customer Service Office Tipperary Town, Ircland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) BZ 062-52155

Page 3

Conversion Instructions

for

Missile Command”

to

Crystal Castles”

Page 4

Conversion Instructions

© 1984 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of'a phonographic recording, nor may it be stored in a retrieval system, transmitted, of otherwise copied for public or private usc, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. ‘This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending, Ifintringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases, Infiingers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five yeass.

Atari will aggressively enforce its copyrights against any infringes. We will use all legal means to:immediately halt any manufacture, distribution, or operation of a copy of vidco games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari, Inc 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed in the US.A. 5N

Page 5

Conversion Instructions

Safety Summary

The following safety precautions apply wo all game operators and service personnel. Specific warnings and cautions will be found throughout this manual whete they apply.

& WARNING A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to in stall a grounded outlet, Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding clip is timly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game's power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AG power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be uken to avoid clectical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands ‘or with metal objects! Always discharge the high voltage from the CRT beforeservicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap, Wait two minutes and discharge the anode again. ‘Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non. ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent nube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. ‘Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, volt age raling, and current rating. In addition, the fuse cover must be in place during game ‘operation.

CAUTION

Properly Attach All Connectors. Make sure thatthe connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fitonly one way: If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warrancy,

Page 6

Conversion Instructions TM-266

Introductions of: 4 jis 8 BBR et ee Get lal mn = L Bit Parte Tnvetory . 2. 206 pon ee Ee ee | Tools Required... . 2.27 ee Te ee Conversion Instructions, cen. sere Pose 8 Piet) pes My eee a ZF A. Remove the Control Panel, Attraction Panel, & Display Shield. . . . 3 B. Disconnect the Main Harness & Remove the Game PCBS... . 2.44.6 C, Install the PCB Mounting Panels»... eee ee ee D. Apply the Side-Panel Decals... ..e.e e ee eee eG =. Install the EMI Cage and Printe@-Circuit Boards... .....-- 10 F. Install the Crystal Castles Main Harness... . . - Fe Weeteaetien 3, La) G. Modify the ‘Goin'mocd. 0. Bees oe ee ee ee eee es TO H. Modify the Speaker/Attraction Panel. 2... . eee ee ee wad I, Assemble the Control Panel... .. 2... tees eee e ee J. Install the Attraction Panel, Display Shield, & Control Panel . . . 16 K. Install the Crystal Castles Labels... 0. ee eee eee 17 Te Inspectcthe Games. 2 i's 6 hells eons wen ul My Se ee M. Self-Test. . « 2 srwasy wn piwle Pew s 6 yale le me ee & 7 N. Setting the Option Switches 6613-78. ec a eee 17

  • Crystal Castles Schematics... ........-.% ea eee s a7

LIST OF ILLUSTRATIONS Figure 1 Removing the Control Panel, Attraction Panel, and Display Shield... 2... eee ee ee eee ee Figure 2 Removing the PCBs and Cleating. . 2... eee ee eee 5 Figure 3. Installing the PCB Mounting Panels and EMI Cage... ....7 Figure 4 Apply the Side-Panel Decals... 2. ee eee ee eo Figure 5 Installing the Printed-Circuit Boards... .........11 Figure 6 Installing the Harness - 2. es pe te et eee eee ee Figure 7 Modifying the Attraction Panel/Speaker ..-.........14 Figure 8 Crystal Castles Control Panel (with Parts List)....... 15

LIST OF TABLES Bable DRG Parte: enema: tone Tnleaeeeplee 6 oe 2 EE Sw we See Table 2 Tools Required. «1... 22. ee ee ee eee trees Ne

Page 7

INTRODUCTION

This document includes the instructions necessary for changing your upright Missile Command® game into a Crystal Castles™ game. The instructions include:

  • replacing the control panel, attraction panel, and display shield; (2) replacing the main wiring harness, game printed-circuit board (PCB), and remount ing the Regulator/Audio PCB; and (3) applying new side panel decals, The procedures are organized to accomplish the change in the most efficient manner,

A Crystal Castles instruction manual and schematic package is included with the kit. Keep your Missile Command instruction manual and schematic package for information pertaining to those parts of the game that are not modified by this conversion.

NOTE

Do not discard this document after the conversion is completed. Keep this document as a supplement to the Crystal Castles operators manual.

KIT PARTS INVENTORY

Check the contents of the Crystal Castles Conversion Kit before proceeding with the conversion. The parts included in the kit are listed in Table 1.

Table 1 Kit Parts 4042330-01 Part No. Deseript ion 4040721-01 Crystal Castles EMI Shield PCB and Game PCB Assembly A042342-01 Main Harness Assembly A042331-01 Control Panel Assembly (see Figure 8 and accompanying parts list) A042561-01 EMI Cage and Guides Assembly

034536-02 1/2-Inch Foam Pad (placed between mounting panel and Regulator/Audio PCB) 035402-01 Crystal Castles Attract ion Panel 038086-01 Shock Warning Label 038158-03 Product Identification Label

039450-01 FCC Compliance Label 042305-01 Left Side-Panel Decal (opt ional) 042305-02 Right Side-Panel Decal (optional) 042334-01 Crystal Castles Attraction Panel Decal

Page 8

Conversion Instructions TM-266

Table 1 Kit Parts, continued A042330-01 Part No. Descript ion

042336-01 Video Display Shield 042338-02 Regulator/Audio PCB Mounting Panel 042339-02 EMI Cage Mounting Panel 042341-91 Main Wiring Diagram

042410-01 Crystal Castles Kit Label 175004-708 48 Flat Fiber Washer (for mounting Regulator/Audio PCB) 176015-112 #10 x 3/4-Inch Cross-Recessed Pan-Head Screw (for harness and PCBs) 176020-220 #8 x 1 1/4-Inch Cross-Recessed Screw (for PCB mount ing panels)

179002-001 16-22 AWG Tap-Splice Connector 08-0302356 Crystal Castles Poster 75-050B #10 Lock Washer (for mounting panel) 75-OLOF #10 Flat Washer (for PCBs) 75-9951 #10-24 Nut/Washer Assembly (for speakers) 82-8116B 410-24 x 1-Inch Button-Head Screw (for speakers) TH-241 Crystal Castles Operators Manual T266 Crystal Castles Installation Instruct ions SP-241 Crystal Castles Schematic Package st-241 Crystal Castles Self-Test Chart

‘TOOLS: JLRED The tools listed in Table 2 are required to perform a complete conversion.

Table 2 Tools Required Tool Purpose Phillips-Head Screwdriver Remove and install harness and PCBS Hammer Remove PCB cleats and foam pads Flat—Tipped Screwdriver Remove PCB cleats and foam pads Pliers Removing tie wraps and installing

7/16-inch wrench tap-splice connectors Remove and install the control panel 1/8-Inch Allen Wrench Remove and install retainers 4-Quart Pail & Sponge Install decal graphics Squeegee Install decal graphics X-ACTO™ Knife Install decal graphics Electric Drill w/ 1/4" Bit Modify speaker/attraction panel Brayer (or burnisher) Installing attraction panel decal

Page 9

TM-266 Conversion Instructions

CONVERSION INSTRUCTIONS

ho WARNING hy To avoid electrical shock, unplug the game before performing the conversion procedures,

NOTE

All interior and exterior surfaces of the cabinet and the working area should be clean and free of foreign material before starting the procedures.

The following procedures are arranged in the sequence recommended for performing the game conversion,

A. REMOVE THE CONTROL PANEL, ATTRACTION PANEL, AND DISPLAY SHIELD

i,

ay Unlock and open the rear access panel and the coin door. Remove the coin box.

Fram the front of the game, loosen (do not remove) the three buttonhead screws securing the retainer between the display shield and attraction panel using the 1/8-inch Allen wrench.

Using a 1/8-inch Allen wrench, remove the three screws and washers that secure the upper attraction panel retainer. Remove the retainer.

Slide the attraction panel forward. Disconnect the speaker wires and remove the wires from their tie wraps. Remove the attraction panel by tilting it toward you and then sliding it off of the cabinet.

Reaching through the coin door, remove the carriage bolts, washers, and wingnuts securing the control panel (see Figure 1).

Lift the control panel and tilt it toward you.

Remove the display shields by sliding them off of the support cleats.

Disconnect the control-panel harness. Using a 7/16-inch wrench, remove the nuts, washers, and carriage bolts that secure the control panel. Remove the control panel. Save the hardware for installing the Crystal Castles control panel,

Page 10

Conversion Instruct ions TM-266

Upper Retainer

Speaker/Attraction Panel

‘Speaker Harness

Lower Retainer

Control Panel Harness | Wing Nut

Carriage Bolt Coin Deor

Control Panel

Figure 1 Removing the Control Panel. Attraction Panel. and Disnlav Shield

Page 11

‘™-266 Conversion Instruct ions

Remove Cleats ‘and Foam Pad

Remove PCB:

a

Disconnect Harness

Remove Cleat

Figure 2, Removing the PCBs, Main Harness, and Cleats

Page 12

Conversion Instructions TM-266

B. DISCONNECT THE HARNESS AND REMOVE THE PRINTED-CIRCUIT BOARDS

Fran the rear of the cabinet, disconnect the harness from the gane PCB, and video display. Leave the harness attached to the Regulator/Audio PCB. Fran the front of the cabinet, disconnect the harness from the coin door.

The power distribution and audio output portions of the Missile Command harness will remain intact.

Remove the game and Regulator/Audio PCBs using a Phillips-head screwiriver to remove the screw and fiber washers located in the upper right corner of each PCB (see Figure 2).

Using a flat-tipped screwdriver and pliers, remove the staples and tie wraps that secure the harness to the side of the cabinet.

Using a hammer and chisel, remove all existing PCB support cleats, blocks, and foam pads, Make certain the side panel and underside of the display-support cleat are free of obstructions (e.g., wood slivers and staples) .

INSTALL THE PCB MOUNTING PANELS

Place the EMT cage mounting panel flush with the underside of the display-support cleat. Slide the panel into the cabinet until it stops against the coin-box support. Secure the panel with three 1-1/4 inch Phillips-head wood screws,

Install the Regulator/Audio PCB mounting panel on top of the cabinetbase cleat and align it with the rear edge of the EMI cage mounting panel. Secure the panel using two 1-1/4 inch Phillips-head screws (see Figure 3).

Remove the protective backing fran the 1/2-inch foam pad and apply the pad to the Regulator/Audio PCB mounting panel as shown in Figure 3.

APPLY THE SIDE-PANEL DECALS (Opt ional)

NOIE

The Crystal Castles side-panel decals are not included in the kit, However, if you wish to purchase these decals, use the order form provided at the back of this document.

Page 13

Phillipe-head Screw

‘Coin Box Support

¥4-Inch Foam Pad.

ips-head Screw Conversion Instructions

Display ‘Support Cleat

EMI Cage Mounting Board

EMI Cage

Leave %-Inch Gap

< Regulator/Audio PCB ‘Mounting Board

Base Cleat

Figure 3. Installing the PCB Mounting Panels and EMI Cage

Page 14

Conversion Instructions TH 266

10.

Ww

12.

13. Mix a nommal solution of any liquid dishwashing detergent and approximately three quarts of water in a bucket.

Clean all oil film and dust from the sides of the cabinet and fill any dents or gouges with a filler material.

NOTE

We recommend that the following procedure be performed by two persons. One person may have difficulty handling the Cabinet and the large decals.

Tip the game cabinet and gently lay it on one side on a blanket.

Use a sponge to liberally apply the water and detergent solut ion over the entize side of the cabinet.

Grasp the top edge of the appropriate decal for the side of the cabinet. Hold the decal up and off of the floor and peel away the protect ive backing.

Gently lay the decal, sticky side down, on the wet surface of the cabinet. Position the decal ensuring that the graphics are centered on the side of the cabinet.

Align the bottan and rear edges of the decal with the bottom and rear edges of the cabinet (see Figure 4).

After the decal is in position, use a squeegee to squeeze all the excess water and detergent from beneath the decal by quickly working fram the center to the outside edges. HINT: If any air bubbles form, puncture then with a pin or the tip of an X-ACTO” blade, Rub gently with a soft cloth to disperse the trapped air.

Carefully insert a #11 X-ACTO blade (or suitable substitute) between the Tmolding and the edge of the side panel and, following the contour of the cabinet, cut off the excess decal, Rub the edges firmly with a cloth to smooth down any rough edges (see Figure 4).

When the wrinkles are removed and the decal is free of all excess water and detergent, gently turn the game cabinet over to the opposite side. Be careful to avoid damaging the freshly applied decal.

Repeat steps 4 through 9 for the remaining decal.

Carefully raise the cabinet to the upright position.

Use a lint-free cloth to wipe off any excess water and detergent fron inside and outside of the cabinet. Allow time to dry before proceeding.

Page 15

eae TM-266 Conversion Instructions

‘Side-Panel Decal

‘Trim carofully along edge

Press down working outward from center ‘angn ascent rearand botiom edges of cabinet

Figure 4 Applying the Side-Panel Decals

Page 16

Conversion Instructions ‘TM-266

E, INSTALL THE EMT CAGE AND PRINTED CIRCUIT BOARDS

The Crystal Castles game PCB is shipped inside of the EMI cage with the EMI Shield PCB attached. No assembly is required.

ds Install the EMI cage (and PCBs) by sliding its tabs into the lower cleat. Secure the cage with two 3/4-inch Phillips-head screws (see Figure 3). Be sure to leave a 1/2-inch space to attach the grounding clip.

2 Install the Regulator/Audio IT PCB into its cleats. Secure the PCB with one Phillips-head screw and two fiber washers (see Figure 5).

F.__INSTALL THE CRYSTAL CASTLES HARNESS

The power distribution and audio output portions of the Missile Command harness will remain intact. Perform the following procedures to install the Crystal Castles main harness.

ile Attach the Crystal Castles main harness to the edge connectors of the

EMI Shield PCB, the video display signal input connector (use either the red OR white connector), and to the harness connector for the coin door.

25 Remove the Missile Command harness from the Regulator/Audio PCB at connector P7 and replace it with the Crystal Castles harness connector (see Figure 6).

  • Using the tap-splice connectors provided, attach harness wires to those from power-supply connector P5 (see Figure 6) using pliers. For easy access to P5 and the harness wires, remove the tie wraps as necessary.
  • Attach the green ground wires to one of the power-supply mounting screws.
  • Attach the ground clip to the BMI cage.
  • Secure the harness to the cabinet using the nylon tie wraps and 3/4-inch Phillips-head screws (see Figure 6). Wrap the portions of the harness not used around the harness secure to the cabinet.

G. MODIFY ‘THE COIN DOOR

The Crystal Castles harness has no provision for coin-lockout coils (part number 99-1004, see illustration in Missile Coumand manual). Remove or disable the coin-lockout coils if they exist in your game.

Page 17

ond

ae} ‘TH-266 Conversion Instruct ions

EMI Shield PCB

RegulatoriAudio PCB

Figure 5 Installing the Printed-Circuit Boards

ll

Page 18

Conversion Instruct ions T™M-266

Tie Off Unused Connector ControlPanel, ‘Connector

‘ToVideo Display EMIShield PCB.

Crystal Castles: Harness

RegulatorfAudio PCB.

Connector

Temas Power Supply Connector PS,

Cut 1 oF 2 ties as required

Apply pressure to outside edge of

connector with tip of pliers

Orange/Biack

Ping or tt To Crystal Slue/Green or Blue Castles Harness

Pin or 10 Blue

‘Some wires omitted for clarity

‘Tap-Splice Connectors

Power Supply. Connector PS

Figure 6 Installing the Harness

Page 19

‘TH266 Conversion Instructions

A. MODIFY THE SPEAKER/ATTRACTION PANEL

  • Using pliers or a flat-tipped screwdriver, remove the staples securing the speakers to the wood blocks.
  • Using an electric drill with a 1/4-inch drill bit, drill out the rivets holding the speakers and grilles to the attraction panel. Discard the old panel and the wood-block spacers. Save the cardboard gaskets, speakers, and speaker grilles for reuse.

a Remove the protective paper from both sides of the attraction panel.

  • Remove the backing fram the Crystal Castles attraction decal.
  • Carefully align the speaker holes in the decal with the holes in the Crystal Castles attraction panel.
  • Press the decal in place using a brayer or smooth burnisher. Start fran the center and work outward to the edges to avoid trapping air under the decal.
  • Mount the speakers, gaskets, and speaker grilles to the attraction panel (see Figure 7). Turn the grilles over to conceal any damage from drilling.
  • Secure the speakers, gaskets, and grilles using 10-24 x l-inch buttonhead screws, lock washers, and nut/washer assemblies. Install the speakers so that the metal tabs on each speaker point toward each other.
  • ASSEMBLE THE CONTROL PANEL

Apply the Decal

Ls Using an X-ACTO™ knife, carefully make a horizontal slit in the protective backing sheet on the Crystal Castles control-panel decal to divide it into two parts. DO NOT cut into the decal.

a Remove the upper half of the protective backing fran the decal.

  • Carefully position the Crystal Castles decal so that the holes in the decal align with the holes in the control panel.

4, Using the palm of your hand, press the decal firmly against the control panel. You will need to wrap the decal around the control panel.

  • Remove the bottan half of the protective backing sheet from the decal and repeat step 4.
Page 20

Conversion Instruct ions TM-266

NutWasher Assy

‘Speaker

Button-head Screw

‘Speaker Grille

Attraction Panel with Decal

Figure 7 Assembling the Speakers and Attraction Panel

Page 21

aer200 Uonversion instructions

177010. Locknut Bolt 75-9910NO 179030-004 Nol Red Pushburion

160013-001 Laat Switch ‘and Bu'tor Holosr

‘A088038-02 a73128-001 Lighted Midi Tek-Bell Asay Grounding Cip

AD405BI-01 j 04233201 Hamess f Control Pene! Players may receive an electrical fi shock this cortral panel's net pro o42333-01 erly grounded. After nstalling the Decal—Net Snowe ‘contre! panel, make sure that grounding clio is scoured to ine ‘etal lab Gn ‘heinsido! the control pane!

Figure 8 Crystal Castles Control Panel Assembly A042331-01 A

Parts List

Fart No. Description

038038-02 Lighted Midi Trak Ball™ Assembly A040581-01 Control Panel Harness Assembly 042332-01 Control Panel 042333-01 Control Panel Decal 160013-001 Leaf Switch with Button Holder 177010-240 #10-24 Hex Locknut 178030-004 Red Pushbutton Assembly 179125-001 Grounding Clip 75-5148B 10-24 x 3-Inch Black Carriage Bolt 75-9910N0 5/8-11 Stamped Nut 786900402 1/4 x 1/8-Inch Thick Black Foam Tape

15.

Page 22

Conversion Instructions ‘TM-266

~

Install the Hardware

an Insert the red pushbutton through the back of the control panel. Then place the leaf switch and button holder over the pushbutton (see Figure 8).

2 Secure the parts together using the 5/8-inch stamped nut. Tighten until secure.

  • Attach the ground lead to the metal extrusion on the control panel.

Install the Lighted Trak-Ball”

Le Align the holes in the Trak-Ball assembly with the holes in the control panel.

  • Fram the top of the control panel, insert four 3-inch carriage bolts through the Trak-Ball and control panel (see Figure 8).
  • Fram the bottom of the control panel, install four locknuts onto the carriage bolts. Do not tighten to more than 18 lbs, of torque,
CAUTION 7" Over-torquing will cause binding of the bearings and Trak-Ball, which will result in excessive wear or damage to the Trak-Ball assembly.

J. INSTALL THE ATTRACTION PANEL, DISPLAY SHIELD, AND CONTROL PANEL

  • Attach the speaker wires to the speaker tabs.

Bs Using a 1/8-inch allen wrench, mount the attraction panel to the cabinet with the upper retainer, three screws, and washers (see Figure 1).

3s Install the Crystal Castles control panel with three carriage bolts, washers, and nuts. Place the foam strip (included in the kit) on the edge of the control panel that touches the display shield. Attach the harness connector to the Crystal Castles harness. '

4 Peel the protective paper off of the Crystal Castles display shield. Install the Crystal Castles display shield.

S Close the control panel and using a 7/16-inch wrench, secure it with the carriage bolts, fender washers, and wing nuts. ~

  • Using a 1/8-inch allen wrench, tighten the button-head screws that secure the lower attraction panel retainer.
Page 23

anr-200 Vouversiun instruct Lens:

K. INSTALL THE CRYSTAL CASTLES LABELS

x Do not remove or cover the existing labels on your game,

  • Remove the protective backing from the Product ID label, FOC label, and shock warning label included in the Crystal Castles kit.

3, Apply the three labels to the back of the game cabinet directly above the rear access panel.

L, INSPECT THE GAME

  • Before applying power, inspect the game to ensure that all procedures have been completed correctly.
  • Check that all hardware is firmly attached and that the harness is properly and firmly connected. Make sure all ground wires are attached.
  • Make sure the cabinet and components are free of dust and debris.

4 Plug in the game power cord and turn on the power switch.

& If the screen is jumpy or scrolls, remove the Crystal Castles harness connector you installed into the video display signal input connector, and replace it with the other connector fran the Crystal Castles harness that was not used.

M, SELF-TEST

1, Staple or tape the Crystal Castles self-test chart on the inside of the rear access panel,

  • Perform the self-test procedure as described in Chapter 2 of the Crystal Castles Operators Manual.

N. SET THE OPTION SWITCHES

Verify that the option switches are set to the desired play options for your location. Refer to the Crystal Castles operators manual for option switchlocation and setting information.

  • CRYSTAL CASTLES SCHEMATICS

‘The Crystal Castles Schematic Package is provided for the game circuitry. However, save the power supply and display schematics from the schematic set originally provided for your Missile Command game.

vv

a

Page 24

To Receive a Free Set of Multi-Color Side-Panel Decals

‘The multi-color side-panel decals for your Crystal Castles™ Conversion Kit were not included when the kit was shipped to you. However, if you wanta set, mail this letter to Atari Customer Service and they will send you these decals at no charge, while supplies last. No postage stamp is necessary if mailed in the USA

‘The part numbers of the decals are: Left—042305-01, and right—042305-02

Game Se:

No, cas was shipped

Name

Firm

adciess

civy Sea Bp

AreaCode Phone

COperatar Othe:

Page 25

“Tape This Fage

Atari Inc. Atta: Field Service/Coin-Op Division 737 Sycamore Drive BO. Box 906 Milpitas, California 95035

Second Fold

Page 26

Kit Warranty

Seller warrants that its electronic parts supplied in this kit are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of ship. ment. None of the Seller's other products ar parts thereof are warranted Ifthe electronic parts supplied in this kit fail to conform to this warranty y shall be. at its option, to repair, replace, or Credit Buyer's account for such electronic parts which are returned to Seller during said warranty period, provided: {a) Seller is promptly notified in writing upon discovery by Buyer that said products ate defective;

  • Such products are returned prepaid to Seller's plant; and (©) Seller’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. Inno event shall Seller be liable for loss of profits, lossof use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Soller and Buyer which contract supersedes the terms berein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for @ par ticular purpose, and of all other obligations or liabilities on the Seller's part, and it neither as sumes nar authorizes any other person to assume for tbe Selier any other llabilities in connec tion witis the sale of products by Seller.

‘The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari- supplied components with our games, in order to ensure your safety. Atari distributors re independent, being privately owned and operated. In their judgment they may sell parts ot accessories other than Atari parts or accessories, Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor,