CATHODE RAY TOMES

Marvel Super Heros

Marvel Super Heroes (Europe 951024) (Capcom, 1995) · Manual · 21 pages · 29 sections · original scan

Page 1

MARVEL SUPE® HEROES TW & © 1978 MAFIVEL ENTERTAINMENT GROUP, INC. ALL RIGHTS RESEPVED, ‘© CAPCOM CO.,LTD. ECAPCOM U.S.A. INC. 1995 ALL RIGHTS RESERVED ‘THIS VIDEO GAME IS PRODUCED UNDER LICENSE FROM MARVEL ENTERTAINMENT GROUP, INC.

OPERATORS MANUAL

WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

CARCOMY COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (708) 797-6192 PM00132-KIT Fax: (708) 797-6306 410895

Page 2

CQAPEONI? com-or, inc. MARVEL SUPER HEROES™ THANK YOU FOR PURCHASING MARVEL SUPER HEROES™ VIDEO KIT. WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: FIELD SERVICE - VIDEO PRODUCTS 3311 N. KENNICOTT AVENUE ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE: (708) 797-6192 FAX: (708) 797-6306

THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

"B" CARTRIDGE SERIAL NUMBER AAMA SERIAL NUMBER

"A" CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) 300900

DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:

“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL #

“A” KIT A-CARTRIDGE SERIAL #

“B” KIT B-CARTRIDGE SERIAL # AAMA SERIAL #

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 3

CARGO comn-op, inc. MARVEL SUPER HEROES™

TABLE OF CONTENTS

Warranty Information siuevecuanestiscusssnnsderevsatessnises vs ssaestsssbetsasasbaiseasseceosoeeered ii

Kit Inspection a aeacasessscnssesescscacsesecusasecsueaeacseeeencucesesseseneatseeesesteesaee 1

Kit Installation “FULL” Kit Preparation 3 Installation 3 Marquee 3 Control Panel Wiring 4 Test Bracket 6 Game Cartridges 6 “A” & “B” Kit Preparation and Installation o.o..cesessseesssseseseecsesececsesesecsesesececscsescsesesesseseceeeeeseeeeeeee 7

Test Mode Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menu System Configuration Game Configuration

Cable Wiring JAMMA Connections eesssessssscsesesesescsesssssesenesscsceesusvesssescsesessesssneneneeeseneeeneee 14 Auxiliary Cable Connections 0 cassssesesssssesesesssescseseesesescscucncecscsesececsesesesucneneseaeseeeeeneee 14

Template : Control Panel Drill Hole(s)

Page 4

CANP@EON coin-op, inc. MARVEL SUPER HEROES™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. CPS II System Cartridges: One (1) Year B. Electronic and Mechanical Components: (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.OP, INC.

Page 5

CAP@OM coin-op, nc. MARVEL SUPER HEROES™

KIT INSPECTION

There are three kits available for conversion to MARVEL SUPER HEROES™.

  • MSH1000 (“FULL” kit) contains the complete game cartridges, all necessary graphics, and replacement joysticks and button switches. The “FULL” kit is intended for conversion of most JAMMAcompatible, horizontal screen cabinets.
  • MSH1000A (‘‘A” kit) is compatible only with current CAPCOM® System II games. It is similar to the “FULL” kit but does not include both cartridges (only the A-cartridge is supplied). For operators who have previously converted a cabinet with a “B” kit, the purchase of an “A” kit will provide all the additional components necessary for “FULL” cabinet conversion (“A” + “B” = “FULL”)
  • MSH1000B (““B” kit) contains the game software cartridge (B-cartridge) and must also be installed to a current CAPCOM® System II game. It includes all the necessary game graphics for a cabinet conversion (marquee, control panel overlay, monitor card, etc.).

Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

KIT PARTS LIST

‘A-00532CPS Il System Cartridges (A/B )1
ZZ1400ACPS II System Cartridge ( A )1
|VvA-00533CPS II System Cartridge (B )1
V[VAW00174Monitor Card1
VBlAWO00171Marquee1
VvVvAW00173Overlay, Control Panel1
vVvAW00175Decal, Joystick & Button Switches1
vVAW00176Decal, Cabinet Side2
VVvAW00172-01Decal - Left, Game Play Instruction1
VVAW00172-02Decal - Right, Game Play Instruction1
VvVvVPM00132-KITManual, Operators1
VVv03-0052Cable, Auxiliary1
VVGE2030Joystick2
vV16-0130Switch, 1-Player Start Button (White)1
VV16-0131Switch, 2-Player Start Button (White)1
VVv16-0133Switch, Punch/Kick Button (Red)4
VV16-0134Switch, Punch/Kick Button (Blue)4
vV16-0147Switch, Punch/Kick Button (Yellow)4
Vv03-0050Bracket, Volume/Test1
VV13-0066Bracket, A-Cartridge Mounting4
vV| $C00104-05Screw, Wood4
y13-0141Clamp, Case2

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 6

CAPO coin-op, nc. MARVEL SUPER HEROES™

CAUTION

Please read the following instructions to keep the PC board in good condition:

¢ Do not block the ventilation slots.

¢ Do not drop or bump the board.

¢ Do not spill any liquids on the case.

¢ Do not disassemble the case.

ATTENTION

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the ~ municipal waste system. Check with your local solid waste official for Ni-cd details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

OF YOUR REPAIR WARRANTY.

2 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

® GANPEON? coin-op, inc.

“FULL” KIT INSTALLATION ZN WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) or cartridges from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the Drill Hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel *cover (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *Cover is not included in the kit.
  • Plug up unused holes with a wood dowel (1- 1/8" diameter) and sand any rough edges.

INSTALLATION

Marquee Installation

  • Remove the marquee glass, old marquee overlay, and the old cabinet graphics.
  • Install the new marquee and replace the *glass. *Glass is not included in this kit.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges. MARVEL SUPER HEROES™
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel *cover (if required).

Figure 1 Overlay Installation

Reassembly of Components

  • Install all buttons and retaining rings on the control panel as shown in Figure 2. Install two RED buttons to the immediate right of each joystick, install two YELLOW buttons to the right of the red ones, and install two BLUE buttons to the right of the green ones.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM COIN-OP, INC. 3

Page 8

CAPEOIM* coin-op, INC.

Control Panel Red Yellow Blue Red Yellow Blue

Red Yellow Blue Red Yellow Blue

Buttons: >)

=

Nan

Retaining ZS

Rings Switches SF ce <A

FIGURE 2 Control Panel Buttons and Switches

  • Notice that there are two white buttons. (See Figure 3.) The WHITE buttons are START buttons. Install the PLAYER ONE button on the top lefthand side of the control panel, and the PLAYER TWO button on the top right-side of the control panel.

1 Player: 2 Player

FIGURE 3 Start Buttons

  • Install the switches on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in Figure 4. MARVEL SUPER HEROES™

FIGURE 4 Joystick Installation

CABINET DECAL INSTALLATION

  • Remove monitor glass and install monitor card.
  • Peel-off the backing to the instruction decals and place on both the left and the right sides of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

MONITOR CARD INSTRUCTION DECAL-LH

‘CABINET DECAL INSTRUCTION DECAL - RH

FIGURE 5 Cabinet Decal Installation

4 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 9

ICAR COMA eae

WIRING MARVEL SUPER HEROES™

‘TO GAME CASE CONNECTOR

NOTE: All switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.
  • Reconnect the existing JAMMA connectors to the control panel according to the chart in Figure 5.
  • Connect the Player 1 and the Player 2 Kick buttons to the auxiliary cable harness connectors shown in Figure 6. Make the connections according to the chart in Figure 7.

JAMMA CONNECTOR REF. *WIRE COLOR CONNECTS TO TO PUSH-BUTTON SWITCHES

10 VOLUME & TEST SWITCHES

FIGURE 6 Auxiliary Cable Harness

COMPONENT JOYSTICK FUNCTION

JOYSTICK. JOYSTICK, JOYSTICK PUNCH BUTTON. PUNCH BUTTON. ‘WHITE/BLUE PUNCH BUTTON.

VIOLET/BLACK JOYSTICK. VIOLET/BROWN JOYSTICK. JOYSTICK VIOLET/ORANGE JOYSTICK VIOLET/YELLOW PLAYER 2 PUNCH BUTTON. VIOLET/GREEN PLAYER 2 PUNCH BUTTON VIOLET/BLUE PLAYER 2 PUNCH BUTTON.

Figure 6: JAMMA Wiring Connections

  • Wire Color Note:

assignments; your harness may contain different colors than shown above.

AUXILIARY CABLE CONNECTOR REF. CONNECTS Wire colors shown are according to the AAMA -AMOA Standard for wire color

COMPONENT FUNCTION

WIRE COLOR TO

BLACK,PLAYER |KICK BUTTON,COMMON
19BLUEPLAYER 1KICK BUTTONLIGHT
17REDPLAYER 1KICK BUTTONMIDDLE.

PINK PLAYER 1 KICK BUTTON HEAVY

BLACK, PLAYER 2 KICK BUTTON. ‘COMMON

21GRAY/YELLOW.PLAYER 2KICK BUTTON.LIGHT
3PINK/YELLOW,PLAYER 2KICK BUTTONMIDDLE.
9PURPLE/YELLOW.PLAYER 2KICK BUTTON.

HEAVY.

GRAY/YELLOW. TEST BRACKET VOLUME SWITCH UP. PINK/YELLOW, TEST BRACKET. VOLUME SWITCH DOWN BLACK/WHITE TEST BRACKET. VOLUME SWITCH

Figure 7: Auxiliary Cable Wiring Connections

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. ‘COMMON

Page 10

CAPCETI coin-op, inc. MARVEL SUPER HEROES™

  • An optional Test/Volume bracket (see Figure 8) GAME CARTRIDGE is included in this kit. Your cabinet may already

contain this bracket. If you decide to install, the INSTALLATION

bracket should be mounted inside the coin door and

  • Install the four (4) mounting brackets to the
topof thhf.

on top of the cash box for easy access. underside of the “A” cartridge as shown in Figure

NOTE: The A-cartridge also contains the same 10. Test and Volume functions found on ES \ the test bracket. = )

‘v300500, ) Figure 8: Test Bracket CE Wiring of the Test Bracket requires connections to both the main JAMMA harness as well as the Figure 10: Mounting Bracket Installation auxiliary cable harness (refer to Figure 9).

  • Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 11.
LEAD WIRESWITCHCONNECTS

COLOR FUNCTION TO YELLOW VOLUME-UP | AUX. CABLE ‘29’(GRAY/ YELLOW)

GREENCOMMONAUX. CABLE

“31’(BLACK/ WHITE)

BLACKVOLUME-AUX. CABLE

DOWN “30° (PINK/ YELLOW)

GREENCOMMONAUX. CABLE

*31’(BLACK/ WHITE)

BROWN TEST JAMMA ‘15’ BLACK GROUND JAMMA ‘A’ or

‘B’ or ‘e’ or ‘f” or ‘1’ or ‘2’ or ‘27° or ‘28’ Figure 9: Test Bracket Wiring Chart Figure 11: Case Mounting

  • Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q- SOUND, also attach the audio cables.

6 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 11

CAPECM* coin-op, inc. MARVEL SUPER HEROES™

  • Continue to follow the “FULL” kit Preparation
WARNING and Installation Procedure, steps 25 through 27.
  • Installation of the “A” kit is now complete.

Improper installation of the JAMMA harness connector to the game cartridge will cause

WARNING damage to the enclosed PCB.
  • Power-up the game and set all operator. DISASSEMBLY OF EITHER GAME adjustable options by pressing the TEST switch. CARTRIDGE WILL VOID YOUR Follow the instructions under the TEST MENU WARRANTY. section of this manual.

“A” KIT INSTALLATION

  • To install the control panel parts, you must “B” KIT INSTALLATION follow the “FULL” Kit Preparation and Installation Procedure, steps 15 through 18, and steps 21-23. 1. To install the cabinet graphics, you must follow the “FULL” Kit Preparation and Installation
  • To mate the existing “B” cartridge with the “A” Procedure, steps 3 through 22. cartridge, align the “B” cartridge over the “A” cartridge and push down firmly. Install the case 2. To remove the existing “A” cartridge from the clamps as shown in Figure 12. “B” cartridge, pull the old case clamps apart and discard (see Figure 12). Carefully remove the old “B” cartridge and install the new “B’ cartridge. Install the new case clamps.
  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU Sp section of this manual.

"A" Cartridge

Figure 12 : Case Clamp Installation

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.OP, INC. 7

Page 12

CAPEOM° coin-op, ine. MARVEL SUPER HEROES™

NOTES

8 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 13

@AP@OM* coin-op, Inc. MARVEL SUPER HEROES™

TEST MENU

The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin mechs, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

  • ACCESSING THE TEST MENU

¢ Fora CAPCOM® cabinet, or a cabinet with a test switch: Make sure the game is on and push the test switch. The screen shown below will appear.

¢ For a cabinet without a test switch: Push the test switch test on the outside of the blue plastic casing. (Refer to the inside back cover of the manual).

TEST MENU

INPUT

OUTPUT

SOUND & VOICE

COLOR

DOT CROSS HATCH

GAME DATA

CONFIGURATION

  • MEMORY CHECK
  • EXIT

SELECT = 1P UP or DOWN START =1P SHOT1

  • HOW TO SELECT AN ITEM
  • Use the PLAYER 1 JOYSTICK to move the arrow in front of the desired item and press the PLAYER I LIGHT PUNCH button.
  • To return to the test menu, push the PLAYER J START and PLAYER 2 START buttons simultaneously. ¢ The test menu will always appear on the screen:
  • After you exit the “7. CONFIGURATION MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.
  • CLOSING THE TEST MENU

To close the Test Menu, highlight “9. EXIT” and push the PLAYER 1 LIGHT PUNCH button.

}Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC, 9

Page 14

CAPCOM coin-op, inc. MARVEL SUPER HEROES™

  • TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved.

OUTPUT Used to test the coin meter and the coin lock.

SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER I JOYSTICK. Push the PLAYER I LIGHT PUNCH button to hear the sound of the selected code.

COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background.

DOT CROSS Used to test the screen size, focus and distortion. HATCH GAME DATA Coin meter and playtime information will be displayed.

CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section.

MEMORY CHECK Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears.

EXIT Select this item and push the PLAYER I LIGHT PUNCH button to return to game play mode.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 15

CAPCOM coin-op, Inc. MARVEL SUPER HEROES™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB rather than DIP switches.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION MENU
  • From the TEST MENU, move the arrow to “7. CONFIGURATION” and push the PLAYER 1 LIGHT PUNCH button. The screen below will be displayed. A description of each option is explained in the table below.
  • CONFIGURATION MEN

. SYSTEM

  • GAME
  • DEFAULT

. SAVE & EXIT

SELECT = 1P UPOR DOWN

START = 1P LIGHT PUNCH

SYSTEM Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER I LIGHT PUNCH and PLAYER I MIDDLE PUNCH buttons at the same time to select this option. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message EXIT “SAVING NEW CONFIGURATION IN EEPROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC, 11

Page 16

GAPROM com-or, inc. MARVEL SUPER HEROES™

SYSTEM CONFIGURATION

CHANGING THE SYSTEM CONFIGURATION SETTINGS

Move the PLAYER 1 JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER I JOYSTICK left or right or press the PLAYER 1 LIGHT PUNCH button to select.

7-1. SYSTEM CONFIGURATION

> 1. COIN MODE 2 COINS 1 CREDIT

. CONTINUE ON

. MONITOR NORMAL

. DEMO SOUND ON

. SOUND MODE STEREO (QSOUND)

  • CHUTE TYPE 1 CHUTE SINGLE
  • EXIT

SELECT OPTION MODIFY SETTING P UP OR DOWN P LEFT OR RIGHT P LIGHT PUNCH OR JUMP

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

SELECT THE CHARGE PER PLAY.

  • CONTINUE SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.
  • MONITOR FLIP FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL.
  • DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET.
NOTE: STEREO SHOULD ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS.
  • CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTES. 1 CHUTE SINGLE: WITH THIS SETTING, EITHER PLAYER CAN START THE GAME. 2 CHUTES SINGLE: TWO PLAYERS USE ONE COIN CHUTE AND PLAY AT THE SAME TIME. THE PLAYER WHOSE COIN WAS PUT IN FIRST STARTS THE GAME. 2 CHUTES MULTI: TWO PLAYERS USE TWO COIN CHUTES AND PLAY SEPARATELY. THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED. TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH THE PLAYER | START BUTTON.

SYSTEM CONFIGURATION OPTION SETTINGS

1COIN 1 CREDIT 1 COIN 2CREDITS 1 COIN

  • CREDITS 1 COIN 4 CREDITS 1 CON 6 CREDITS 1 COIN 7 CREDITS 1 COIN 8 CREDITS 1 COIN 9 CREDITS 3 COINS 1 CREDIT ‘4 COINS: 1 CREDIT ‘5 COINS 1 CREDIT. ‘6 COINS: 1 CREDIT 8 COINS: 1 CREDIT ‘9 COINS 1 CREDIT.
  • COINS START 1 COIN CONTINUE FREE PLAY
  • CONTINUE ON ‘OFF 3, MONITOR FLIP. NORMAL 4, DEMO SOUND. OFF ‘5. SOUND MODE ‘ON STEREO (QSOUND) MONAURAL
  • CHUTE TYPE.
NOTE: 1 CHUTE SINGLE

FACTORY SETTING 2 CHUTES SINGLE 2 CHUTES MULTI

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 17

CAP@OLI* coin-op, Inc. MARVEL SUPER HEROES™

GAME CONFIGURATION

CHANGING THE GAME CONFIGURATION SETTINGS

Move the PLAYER 1 JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER | JOYSTICK left or right or press the PLAYER ] LIGHT PUNCH button to select.

  • GAME CONFIGURATION

. DIFFICULTY

. DAMAGE LEVEL

. TIMER SPEED

}. MAX ROUND

JOIN-IN

. EVENT

. MODE 4 MEDIUM

LEVEL 4

4 NORMAL

3 ROUNDS

ON

OFF

NORMAL TURBO

. EXIT

SELECT OPTION MODIFY SETTINGS P UP OR DOWN =1P LEFT OR RIGHT = 1P LIGHT PUNCH OR MIDDLE

GAME CONFIGURATION ITEM DESCRIPTIONS

  • DIFFICULTY SETS THE DIFFICULTY LEVEL.
  • DAMAGE LEVEL SETS THE OFFENSIVE POWER LEVEL
  • TIMER SPEED SETS THE SPEED OF THE COUNTDOWN FROM THE TIMER DISPLAY 4, MAX ROUND SETS THE NUMBER OF ROUNDS PER MATCH: 1 ROUND: WINNER OF A SINGLE ROUND WINS; 3 ROUNDS: WINNER OF 2 OUT OF 3 ROUNDS WINS; 5 ROUNDS: WINNER OF 3 OUT OF 5 ROUNDS WINS. 5.JOIN-IN. SETS THE OPTION TO ALLOW OTHER PLAYERS TO JOIN-IN.
  • EVENT TURNS ON EVENT MODE. USEFUL FOR CHAMPIONSHIP TOURNAMENTS. OFF: NORMAL SETTING. SETS THE MODE TO NORMAL OPERATION. 1 MATCH: MATCHES PLAYER WITH ONE CREDIT. A WIN OR A LOSS RESULTS IN GAME OVER (CONTINUE IS NOT AVAILABLE). ALLOWS FOR AN AUTOMATIC BLOCKING FEATURE FOR MOST CHARACTERS (TO BE USED FOR BEGINNING PLAYERS). RETURN TO THE CONFIGURATION MENU.

GAME CONFIGURATION OPTIONS

  • DIFFICULTY 3 4 EASY HARD | MEDIUM 5 6 MEDIUM. HARD VERY HARD HARD VERY EASY
  • DAMAGE, LEVEL LEVEL 2 LEVEL 5 LEVEL 6 LEVEL 3 | LEVEL 4 LEVEL7
  • TIMER SPEED

‘4. MAX ROUND. 2 3 4 5 6 7 NORMAL _ 1 ROUND, 3. ROUNDS 5 ROUNDS E IN. g OFF 1 MATCH NORMAL TURBO. =NORMAL TURBO BEGINNER

NOTE: [ FACTORY *JOIN-IN FEATURE IS

SETTING DISABLED IN THIS SETTING

without the express permission of CAPCOM CO) 13

Page 18

ICARCOMY COIN-OP, INC. RVEL SUPER HEROES™

JAMMA Connections

SOLDER SIDE COMPONENT SIDE

COIN LOCK 2 *SPEAKER (-) N.C. VIDEO GREEN VIDEO SYNC SERVICE (FREE CREDIT)

2 PLAYER - COIN aS 2 PLAYER - START ae 1 PLAYER - START

2 PLAYER - UPi1 PLAYER - UP.
2 PLAYER - DOWNi|_1PLAYER - DOWN

2 PLAYER - LEFT 1 PLAYER - LEFT.

2 PLAYER - RIGHTb:

2 PLAYER - LIGHT PUNCH 2 PLAYER - MIDDLE PUNCH 2 PLAYER - HEAVY PUNCH NIC NIC GND

NIC NIC NIC NIC PURPLE/YELLOW_| PLAYER 2 HEAVY KICK NIC NIC PINK PLAYER 1 HEAVY KICK RED PLAYER 1 MIDDLE KICK BLUE PLAYER 1 LIGHT KICK

GRAY/YELLOWPLAYER 2 LIGHT KICK|NIC
PINK/YELLOWPLAYER 2 MIDDLE KICKNIC

NIC NIC

NICgNIC
GRAY/YELLOWTEST BRKT- VOLUME UPTEST BRKT-VOLUME DOWN _| PINK/YELLOW

BLACKWHITE _| TEST BRKT-VOLUME COMMON NIC

BLACKPLAYER 2 KICK - COMMON.PLAYER | KICK-COMMON,

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 19

ICARCOMY Nea MARVEL SUPER HEROES™

GAME CASE CONTROLS

COIN REGISTER

COMMUNICATION PORTS a ae (NOT USED) pene

OUT IN

*VOLUME DOWN

JAMMA AUXILIARY CABLE AUDIO OUT (FOR Q SOUND) CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE 300800

*NOTE: IF YOU ARE EXPERIENCING VOLUME CONTROL PROBLEMS, DEPRESS AND HOLD VOLUME DOWN FOR AT LEAST 5 SECONDS AND RELEASE. THEN, SET VOLUME UP FOR APPROPRIATE SOUND LEVEL. FOR SOUND LEVEL VERIFICATION, FOLLOW THE INSTRUCTIONS IN THIS MANUAL UNDER TEST MENU AND SELECT SOUND & VOICE.

TYPICAL CONTROL PANEL LAYOUT OF MARVEL SUPER HEROES™

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 20

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

CARCOMY COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (708) 797-6192 Fax: (708) 797-6306

Copyright © 1995 CAPCOM@coin-op, Inc., All Rights Reserved

Page 21

(CAPRCOM( GOIN-OP, INC. 3311 N. KENNICOTT AVE. ARLINGTON HEIGHTS, ILLINOIS 60004 TELEPHONE: (708) 797-6192 FAX: (708) 797-6306

TECHNICAL SERVICE BULLETIN 95-012

DATE: NOVEMBER 16, 1995

SUBJECT: GAME DIFFICULTY SETTING

GAME: MARVEL SUPER HEROES™

TO: ALL DISTRIBUTORS

TO MAXIMIZE YOUR EARNINGS THE AVERAGE GAME TIME SHOULD BE BETWEEN 2-1/2 TO 4 MINUTES. IF YOUR AVERAGE GAME TIME IS OVER 4 MINUTES, CHANGE THE FACTORY GAME DIFFICULTY SETTING FROM 4 MEDIUM TO 7 VERY HARD.

PROCEDURE TO CHANGE THE GAME GAME DIFFICULTY SETTING:

1, OPERATE TEST SWITCH TO ENTER TEST. NOTE: FOR CABINETS NOT EQUIPPED WITH A TEST SWITCH, PRESS THE TEST SWITCH ON THE “A” BOARD CARTRIDGE. SEE GAME OPERATORS MANUAL, INSIDE OF BACK COVER FOR TEST SWITCH LOCATION.

2. TEST MENU SCREEN. OPERATE PLAYER 1 JOYSTICK TO MOVE CURSOR TO

“7: CONFIGURATION”.

  • PRESS PLAYER 1 LIGHT PUNCH BUTTON TO ENTER “7. CONFIGURATION MENU”.
  • OPERATE PLAYER 1 JOYSTICK To “2. GAME”. .
  • PRESS PLAYER 1 LIGHT PUNCH BUTTON TO ENTER ‘7-2. GAME CONFIGURATION”.
  • OPERATE PLAYER JOYSTICK TO “1. GAME DIFFICULTY”.
  • OPERATE PLAYER 1 JOYSTICK LEFT OR RIGHT TO “7. VERY HARD”.
  • OPERATE PLAYER 1 JOYSTICK DOWN TO “8-EXIT”.
  • PRESS PLAYER 7 LIGHT PUNCH BUTTON TO “CONFIGURATION MENU”.
  • OPERATE PLAYER 1 JOYSTICK TO “4. SAVE & EXIT”.
  • PRESS PLAYER 1 LIGHT PUNCH BUTTON TO “TEST MENU”.
  • OPERATE PLAYER 1 JOYSTICK TO “9: EXIT”.
  • PRESS PLAYER 1 LIGHT PUNCH BUTTON TO “GAME PLAY MODE”.

END

i

(CAD COME ats TECHNICAL SERVICE BULLETIN 95-012 Page 1