PC10 Operation Manual (PCH1-UP)
PlayChoice-10 (Nintendo) · Manual · 36 pages · 7 sections · original scan
‘4
PlayChotice-10
MODEL NO: PCH1-UP
MODEL NO:PCH1-UP-US
Revision 1
This equipment generates, uses,and can radiate radio frequency energy and if not installed and used in accordance with ihe instructions manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
Use of non-Nintendo parts or modifications of your Nintendo game circuitry may adversely affect the safety of your game, and may cause injury to your players.
MEMO
cc 1 Contents [
- Location Setup 1
| A. | Game Inspection -- | 4 |
| B. | Game Installation-- | 2 |
- Voltage Selection--- 3
- Power On/Off Switch-- 4
- Grounding of Game --- 4
- Adjustment of Video Monitor -+-..:--::sssseeeereeeeeeeee eee 5
- Option Switch Settings 7
| A. | Game Settings | 8 |
- Self-Test and Bookkeeping -------.::--- ieee erect eee 9
- Maintenance and Repair --- A. Fuse Replacement **" B. Cleaning Cc. Operation Panel -- D. Video Monitor Removal E. Game PCB Removal and ROM PBC Exchange-:-:-:++--- 14
- Radio Frequency Interference cece eeeeeeceeeeaeeeeee 14
- Wiring and Connection vvrricitertiees 15
- Parts Lists -cccccccctrccccrett eset ct eter te ee eeete ees + 17 PCH1-UP Game Cabinet Assembly .. PCH1-UP Operation Panel Assembly PCH1-UP Wiring Harnesses - PCH1-CPU PCB Assembly :-- PCH1-ROM PCB Assembly -- 054-FCC PCB Assembly -- 079-FCC PCB Assembly -- PP-1000A Power Supply Assembly -- PCH1-UP Fuses -LOMNMGVODD
MEMO
A. Game Inspection
PCH Display Panel Game Serial Number Label (Name Plate)
CHP-US Front Screen
PCH
Video Monitor
Video Monitor
Game PCB 079 Shield Cover
Power Supply Assembly
Main Fuse Power On/Off Switch 054 Shield Cage
Power Cord
Power Transformer
Fig. | Game Overview
No. DESCRIPTION (Reference Designations)
| CHPU-88-44 | 100 Ohm 1/2W +5% Carbon Resistor | (R5) |
CHPU-88-45 100K Ohm 1/2W +5% Carbon Resistor (R3, R14)
| CHPU-88-46 | 5.1 | Ohm 5W +5% Cement Resistor | (R1) |
| CHPU-88-47 | 20 | Ohm 5W +5% Cement Resistor | (R22) |
| CHPU-88-48 | 30 | Ohm 5W +5% Cement Resistor | (R10) |
| CHPU-88-49 | 100 Ohm 5W +5% Cement Resistor | (R16) | |
| CHPU-88-50 | 510 Ohm 5W +5% Cement Resistor | (R20) | |
| CHPU-88-51 | 2K | Ohm Veritical Cermet Trimpot | (VR2) |
| CHPU-88-52 | 50K Ohm Vertical Cermet Trimpot | (VR1) |
CHPU-88-53 _ El-40 Type 3D-0163 Switching Transformer (TR) CHPU-88-54 SC2A Choke Coil (L1) CHPU-88-55 SF-C27-00105-01 Choke Coil (L2) CHPU-88-56 3A FGMB NR Type Fuse CHPU-88-57 OG751-0062 Fuse Holder (2 per assembly) CHPU-88-58 Heat Sink Clip (3 per assembly) CHPU-88-53 Thermally Conductive Rubber CHPU-88-60 2-Pin AC Input Connector Receptacle on PCB CHPU-88-61 6-Pin DC Output Connector Receptacle on PCB CHPU-88-62 7-Pin DC Output Connector Receptacle on PCB CHPU-88-65 3D-0163-32 Type Heat Sink
CHPU-88-63 3D-0163-30 Type Metal Frame CHPU-88-64 3D-0163-31 Type Metal Cover CHPU-88-66 3-Pin AC Input Connector Ass’y.on Metal Frame CHPU-88-67 9-Pin DC Output Connector Ass’y.on Metal Frame CHPU-88-68 12-Pin DC Output Connector Ass’y. on Metal Frame CHPU-88-69 Metal PCB Retainer (4 per assembly)
|. PCH1-UP Fuses
PART No. DESCRIPTION(Reference Designations) TKGU-11-08 Main Fuse U.S. 5A 125V CHVU-63-11 Main Fuse Europe 3A 250V
CHPU-88-56 Power Supply Fuse 3A 125V(Midget)
TKGU-11-12 Video Monitor Fuse 20-EZV(R-C), 20-Z2AW 4A 125V(Slow Blow) (F302)
TKGU-11-13 Video Monitor Fuse 20-EZV(R-C), 20-Z2AW 0.3A 125V(Midget) (F301)
MDST-63-12 Video Monitor Fuse XM-2001N 2.5A 125V(Slow Blow) (F702)
MDST-63-13 Video Monitor Fuse XM-2001N 3A 125V(Slow Blow) (F701)
Check before plugging the game in!
The game“PlayChoice-10™” is shipped ready for operation, but a last visual check should be made to insure the final touch of quality control. Please check the following to help us insure that your new game was delivered to you in good condition.
- Check the exterior of the game for shipping damage, dents, chips, or broken parts.
- Remove the screws on the Rear Door Panel.
- Unlock and open the Rear Door Panel, as well as the Service Door inspect the interior of the game as follows:
- Check that Plug-in connectors are firmly connected.
- Check that Plug-in integrated circuits on the Game PCB are firmly connected in their sockets.
- Check that all major subassemblies such as the Power Supply, Operation Panel, and Video Monitor are properly mounted.
- Remove the tie-wrap that holds the coiled Power Cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation.
B. Game Installation
Fig. 2 Installation Requirements
Power : 170 watts Temperature : Oto 38deg.C (32 to 100 deg F) Humidity : Not over 95% relative Space required: 63(W) x 90 (D)cm (24 3/4 x 35 1/2 in.) Height > 189¢cm (74 1/2 in.)
G. O79-FCC PCB Assembly : PARTS LIST
- Voltage Selection
| Before plugging in your game, make sure the Terminal Block of | PART No. | DESCRIPTION (Reference Designations) | |
| the Power Transformer is correct for your location’s line voltage. | PCHU-23-01 | 079-FCC Complete PCB Assembly | |
| PCHU-21-128 | 20 Pin Flat Cable Header | (P1, P2) | |
| CHPU-23-12 | 330 pf 50V Ceramic-Disc Capacitor | (C1~C19) | |
| Outlet through | CHPU-23-13 | Ferrite Beads BL O2RN2-R62 | (FB1~FB19) |
| utlet_ | thro | So |
A 63 +—— |solation
| Power Supply Assembly | q | Transformer (For Upper Monitor Only) | ||||
| 4 | ZB | AC 100V | Terminal Block | H.PP-1O00A Power Supply Assembly : PARTS LIST | Continued | |
| f | LE; | 100VA | US. | ~ | jer | : |
| LE, | MAX. | Europe Sen aee @ | PART No. | DESCRIPTION (Reterence Designations) |
Z QB — =
| % DA | CHPU-88-01 | PP-1000A Complete Power Supply Assembly | ||
| Loy | Serial Fuse | tO) | CHPU-88-02 | 3D-0163 Complete Power Supply PCB Assembly |
| CHPU-88-11 | 3D-3000 Hybrid IC | (IC1) | ||
| CHPU-88-12 | uPC78M24 3-Terminal Regulator | (IC2) | ||
| Main Fuse | CHPU-88-13 | TL431CLP Adjustable Shunt Regulator | (IC3) | |
| Oraoe ey | CHPU-88-14 | TLP541G Photo Coupler | (PC1) | |
| Europe 3A anoy | CHPU-88-15 | PC614 Photo Coupler | (PC2) | |
| (200 ~ 240V) | CHPU-88-16 | RB404/S4VB40 Diode | (D1) | |
| CHPU-88-17 | C25P04Q/20CS04M Diode | (D12) | ||
| CHPU-88-18 | 30DF2 Diode | (D11) |
CHPU-88-19 1S1835/10DF6 Diode (D6, D7, D10, D14)
| Power Transfomer PT-1021A | CHPU-88-20 | 18954 Diode | (D3) |
| baat through | CHPU-88-21 | RDS5. 1EB3 Zener Diode | (ZD1) |
| Fane ner | CHPU-88-22 | 5P2M Thyristor | (Q1) |
| AC 100V | CHPU-88-23 | 2S8C2562 Silicon NPN Transistor | (Q2) |
| 120VA | CHPU-88-24 | 2SC2749 Silicon NPN Transistor | (Q3) |
MAX.
| (Eat Loner Monitor and | Power Transom er oon | CHPU-88-25 | 0.01 uf S0V Mylar Capacitor | (C6, C9, C27) |
| Fluorescent Lamp | CHPU-88-26 | 0.1 uf 50V Mylar Capacitor | (C13) | |
| CHPU-88-27 | 1000 pf 50V Mylar Capacitor | (C12) | ||
| Power On/Off Switch | CHPU-88-28 | 0.047 uf 630V Metallezed Film Cap. | (C1, C4) |
CHPU-88-29 0.22 uf 250V Metallezed Film Cap. (C10, C28, C29) CHPU-88-30 2200 pf 2KV Ceramic-Disc Capacitor (C2,C3,C11,C15,C18)
| CHPU-88-31 | 4.7 uf 50V Al Electrolytic Cap. | (C7) |
| CHPU-88-32 | 47 uf 35V Al Electrolytic Cap. | (C8, C17) |
| CHPU-88-33 | 330 uf 200V Al Electrolytic Cap. | (C5) |
| CHPU-88-34 | 1000 uf 50V Al Electrolytic Cap. | (C16) |
| CHPU-88-35 | 3300 uf 10V Al Electrolytic Cap. | (C19~C26) |
| This game uses one of two types of transformers | CHPU-88-36 | 100 Ohm 1/4W +5% Carbon Resistor (R9,R11,R12,R23,R24 |
)
| which are different in appearance but identical in function. | CHPU-88-37) | 1K = Ohm 1/4W +5% Carbon Resistor | (R4, R6, R15) | |
| The two types can be interchanged. | CHPU-88-38 | 1.5K Ohm 1/4W +5% Carbon Resistor | (R25) | |
| CHPU-88-39 | 2.4K Ohm 1/4W +5% Carbon Resistor | (R26) | ||
| CHPU-88-40 | 10K Ohm 1/4W +5% Carbon Resistor | (R7) | ||
| . | nd Voltage Selection | CHPU-88-41 | 24K Ohm 1/4W +5% Carbon Resistor | (R17) |
| Fig. 3 Power Supply Assembly, Power Transformer and | Voltag: | CHPU-88-42 | 30K Ohm 1/4W +5% Carbon Resistor | (RB) |
| CHPU-88-43 | 5.1 | Ohm 1/2W +5% Carbon Resistor | (R19, R21) |
3 26
PART No. DESCRIPTION (Reference Designations and Locations) PCHU-21-100 5.1K Ohm 1/4W+5% Resistor (R4, R5, R88, R89)
| PCHU-21-101 | 7.5K Ohm 1/4W+5% Resistor | (R16) |
PCHU-21-102 10K Ohm 1/4W+5% Resistor (R12, R34, R38, R41, R44, R51, R54, R61, R64, R74, R82, R83, R87, R92, R93)
| PCHU-21-103 | 12K Ohm 1/4W+5% Resistor | (R71) |
PCHU-21-104 20K Ohm 1/4W+5% Resistor (R6, R39, R70, R72)
| PCHU-21-105 | 100K Ohm 1/4W+5% Resistor | (R33, R75) |
| PCHU-21-106 | 200K Ohm 1/4W+5% Resistor | (R9~R11) |
| PCHU-21-107 | 360K Ohm 1/4W+5% Resistor | (R79) |
| PCHU-21-108 | 750K Ohm 1/4W+5% Resistor | (R78, R80,R84) |
| PCHU-21-109 | 1M Ohm 1/4W+5% Resistor | (R76, R85) |
| PCHU-21-110 | 1.8M Ohm 1/4W+5% Resistor | (R81) |
| PCHU-21-111 | 2.2M Ohm 1/4W+5% Resistor | (R77, R86) |
| PCHU-21-112 | Hex 5.1K Ohm Series Resistor Array | (RM1, RM16) |
PCHU-21-113 | Octal 1K Ohm Series Resistor Array (RM5, RM8~RM10, RM13) PCHU-21-114. Quad 68 Ohm Parallel Resistor Array (RM6, RM7, RM11, RM12, RM14, RM15) PCHU-21-115 | NT-01 Resistor Array (RM2~RM4)
| PCHU-21-116 | 500 Ohm Variable Resistor. Red Cap | (VR1) |
| PCHU-21-117 | 500 Ohm Variable Resistor. Green Cap | (VR2) |
| PCHU-21-118 | 500 Ohm Variable Resistor. Blue Cap | (VR3) |
| PCHU-21-119 | 8 MHz Crystal | (XA) |
| PCHU-21-120 | 20.160MHz Crystal | (X2) |
| PCHU-21-121 | 21.47727 MHz Crystal | (X3) |
PCHU-21-122 DC-DC Converter (Input 5V-Output 12V : MD12P070/150)
| PCHU-21-123 | 8-Station, Single-Throw, DIP Bit Switch | (SW1, SW2) |
| PCHU-21-124 | MINI-BIT Header | (SW3) |
| PCHU-21-125 | 16 Pin DIP IC Socket | (S6~S8) |
| PCHU-21-126 | 28 Pin DIP IC Socket | (S2~S5) |
| PCHU-21-127 | 40 Pin DIP IC Socket | (S1, S9, S10) |
| PCHU-21-128 | 20 Pin Flat Cable Header | (P1) |
| PCHU-21-129 | 96 Pin DIN Connector Receptacle | (CH.1~CH.10) |
| PCHU-21-130 | GL-3HD1 Visible Light Emitting Diode | (LED1) |
E. PCH1-ROM PCB Assembly : Order By Game Name
F. O54-FCC PCB Assembly : PARTS LIST
PART No. DESCRIPTION (Reference Designations) CHPU-23-01 054-FCC Complete PCB Assembly CHPU-23-11 252-28-50-168 56P Edge Connector
| CHPU-23-12 | 330 pf 50V Ceramic-Disc Capacitor | (C1~C30) |
| CHPU-23-13 | Ferrite Beads BL O2RN2-R62 | (FC1~FC30) |
- Power On/Off Switch A Power On/Off Switch is located in the rear of the game at the bottom center of the cabinet. See Fig. 1.
lf the results of the preceding steps are satisfactory, you are ready to plug the game in, and set the Power On/Off Switch to the “On” position.
This game MUST be grounded. Failure to do so may result in destruction of electronic components.
- Grounding of Game (Use only if 3 wire outlet is unavailable.) See Fig. 4
- A grounding wire should be connected to a grounding bar or a metal pipe which is firmly inserted into the ground.
- Do not connect the grounding to a water pipe, because polyvinyl-chloride pipes are sometimes used in water lines, and the electronic continuity to the ground may be interruppted.
- Absolutely do not conneci the grounding wire to a gas pipe, as this can be extremely dangerous.
Fig. 4 Grounding of Game
- Adjustment of Video Monitor
This game uses one of four types of Video Monitors which are different in appearance but identical in function. The four types can be interchanged.
- Video Monitor : [32 Type] 20-EZV(R-C)
- Video Monitor : [33 Type] 20-EZV(R-C)
- Video Monitor : [85 Type] 20-Z2AW
From To Game POB Greet Gain _ Video Montor 6P-600 Vileu Rod Gam JK. Man PCB Hamess . Bie can S Signal POB
INVERT OUT NON INVERT OUT
in case of PCH-UP, Plug in here!
H HOLD smotorsoniavs, OF
Ls
a Mam PCB
V-SIZE Fuse (Midget Type) 0.3A, 125V @} IC 401
DEGAUSS SWITCH ~«—
ee eeD This DEGAUSS SWITCH is H-CENT only attached to Video Monitor [33 Type] and [35 Type] SOUND VOLUME
Fig. 5 Video Monitor : [32 Type] 20-EZV(R-C) [33 Type] 20-EZV(R-C) [35 Type] 20-Z2AW
Do not touch the inside of the Video Monitor It contains Many parts supplied with high voltage. Continued
PART No. DESCRIPTION (Reference Designations and Locations) PCHU-21-59 2SA938 Silicon PNP Transistor (Q11, Q12, Q14, Q15, Q17, Q18)
| PCHU-21-60 | 2SA1015 Silicon PNP Transistor | (Q3, Q5, Q7, Q20) |
| PCHU-21-61 | 2SC1740 Silicon NPN Transistor | (Q8~Q10, Q13, Q16, Q19) |
| PCHU-21-62 | 2SC1815 Silicon NPN Transistor | (Q1, Q2, Q4, Q6) |
| PCHU-21-63 | ES1F Diode | (D1) |
| PCHU-21-64 | 1$5277B Diode | (D3, D4) |
| PCHU-21-65 | EGO1Y Diode | (D2) |
| PCHU-21-66 | DAN401 Quad Cathode-Common Diode Array | (DA1~DA6) |
PCHU-21-67 1.0f 5.5V Electric Double Layer Capacitor (EEC F5R5U105) (C3)
| PCHU-21-68 | 68pf 50V Ceramic-Disc Capacitor | (C44) |
| PCHU-21-69 | 100pf 50V Ceramic-Disc Capacitor | (C35, C36, C45) |
| PCHU-21-70 | 180pf 50V Ceramic-Disc Capacitor | (C11, C39) |
| PCHU-21-71 | 330pf 50V Ceramic-Disc Capacitor | (C2, C6, C12, C40, C41) |
| PCHU-21-72 | 1000pf 50V Ceramic-Disc Capacitor | (C5) |
PCHU-21-73 0.01uf 50V Ceramic-Disc Capacitor (C4, C22, C38, C43, C80~C179)
| PCHU-21-74 | 0.047uf 50V Ceramic-Disc Capacitor | (C15~C17) |
| PCHU-21-75 | 0.2uf 12V Ceramic-Disc Capacitor | (C21) |
| PCHU-21-76 | 0.047uf 50V Film Capacitor | (C33, C34) |
| PCHU-21-77 | tuf 16V Al Electrolytic Radial Cap. | (C7, C8) |
PCHU-21-78 3.3uf 16V Al Electrolytic Radial Cap. (C13, C14, C25, C28, C31, C32) PCHU-21-79 = 10uf 16V Al Electrolytic Radial Cap. (C23, C24, C26, C27, C29, C30, C37, C42)
| PCHU-21-80 | 33uf 16V Al Electrolytic Axial Cap. | (C9, C10) |
| PCHU-21-81 | 47 16V Al Electrolytic Radial Cap. | (C47 ~CS§0) |
| PCHU-21-82 | 100uf 16V Al Electrolytic Axial Cap. | (C18, C46) |
| PCHU-21-83 | 100uf 25V Al Electrolytic Axial Cap. | (C19) |
| PCHU-21-84 | 220uf 16V A! Electrolytic Axial Cap. | (C1) |
| PCHU-21-85 | 470uf 16V Al Electrolytic Axial Cap. | (C20) |
PCHU-21-86 3.3uf 16V Tantalum Electrolytic Cap. (C85, C90, C93, C102, C109, C121, C127, C145;C157)
| PCHU-21-87 | 0 Ohm Shunt Lead | (R99) |
| PCHU-21-88 | 10 Ohm 1/4W+5% Resistor | (R7) |
| PCHU-21-89 | 33 Ohm 1/4W+5% Resistor | (R32, R37, R47, R57, R67) |
| PCHU-21-90 | 51 Ohm 1/4W+5% Resistor | (R8, R19, R23, R27, R31) |
PCHU-21-91 100 Ohm 1/4W+5% Resistor (R17, R20, R24, R28, R68, R69, R73)
| PCHU-21-92 | 110 Ohm 1/4W+5% Resistor | (R23) |
PCHU-21-93 330 Ohm 1/4W+5% Resistor (R13, R14, R18, R21, R22, R25, R26, R29, R30, R36, RYO, R91, R97, R98)
| PCHU-21-94 | 510 Ohm 1/4W2+5% Resistor | (R46, R56, R66) |
| PCHU-21-95 | 820 Ohm 1/4W+5% Resistor | (R1, R2) |
| PCHU-21-96 | 1K Ohm 1/4W+5% Resistor | (R94~R96, R120 ~R131) |
| PCHU-21-97 | 2K Ohm 1/4W+5% Resistor | (R15) |
PCHU-21-98 2.2K Ohm 1/4W+5% Resistor
PCHU-21-99 (R35, R40, R42, R45, R50, R52, R55, R6O, R62, R65) 4.7K Ohm 1/4W+5% Resistor (R43, R53, R63)
D. PCH1-CPU PCB Assembly : PARTS LIST Continued
- Video Monitor : [Y51 Type] XM-2001N PART No. DESCRIPTION (Reference Designations and Locations) PCHU-21-01 PCH1-CPU Complete PCB Assembly
| PCHU-21-11 | Z80A Microprocessor | (5X) | ||||
| PCHU-21-12 | RP2A03E Microprocessor | (1H) | ||||
| PCHU-21-13. | RP2CO3B PPU | (3H) | ||||
| PCHU-21-14. | 27128 16K-Byte EP-ROM 300ns PCH1-C-8T | (8T) | - | |||
| PCHU-21-15 | 2764 8K-Byte EP-ROM 300ns PCH1-C-8K | (8K) | | n= i POnur, | |||
| PCHU-21-16 | 2764 8K-Byte EP-ROM 300ns PCH1-C-8M | (8M) | Set to ‘Nogative” position! | |||
| PCHU-21-17 | 2764 8K-Byte EP-ROM 300ns PCH1-C-8P | (8P) | ||||
| PCHU-21-18 | = TMM2115BP-15 2K-Byte RAM 150ns | (2K) | ||||
| PCHU-21-19 — HM6116 ASP-20 2K-Byte RAM 200ns | (4K, 8R, 8V) | Positive | ||||
| PCHU-21-20 | TC5517 CPL-20 2K-Byte C-MOS RAM 200ns | (aW) | B | AE | & | |
| PCHU-21-21. | N82S129N 256x4-Bit Bipolar ROM PCH1-C-6D | (6D) | Bi | negate | a | |
| PCHU-21-22 | N82S129N 256x4-Bit Bipolar ROM PCH1-C-6E | (6E) | Mle | 2 | ||
| PCHU-21-23 | N82S129N 256x4-Bit Bipolar ROM PCH1-C-6F | (6F) | ean | |||
| PCHU-21-24 | 74LS00 Quad 2-Input NAND | (8J, 6U) | Grea | De | vio Sieh | |
| PCHU-21-25 | 74LS02 Quad 2-Input NOR | (4u) | DEGAUSS SWITCH | From P-800 | ||
| PCHU-21-26 | 74LS04 Hex Inverters | (8D, 3G, 8G, 5u, 7R, 7Y, 4Z) | HHOLD | Video Hames | ||
| PCHU-21-27 | 74LS08 Quad 2-Input AND | (7X) | vse | |||
| PCHU-21-28 | 74LS11 Triple 3-Input AND | (5P) | V-HOLD | |||
| PCHU-21-29 | 74LS14 Hex Schmitt Inverters | (4V) | — HCENT | [js | ||
| PCHU-21-30 | 74LS32 Quad 2-Input OR | (8C, 5T) | grigT | ston owe | ||
| PCHU-21-31 | 74LS42 4 To 10 Decoders | (4T) | ||||
| PCHU-21-32 | 74LS55 2-Wide 4-Input AND-OR-INVERT Gates (5K) | au ese | ||||
| PCHU-21-33 | 74LS74A Dual “D” Flip-Flops (P, CL) | (7J, 7K, 5M) | Os | |||
| PCHU-21-34 | _74LS109A Dual J-K Flip-Flops (PLE, CL) | (4Y) | ) | oa | ||
| PCHU-21-35 | 74LS139 Dual 2 To 4 Decoders | (7H, 2L, 6T) | Co | = | ||
| PCHU-21-36 | 74LS157 Quad 2 To 1 Data Selectors | (7S, 7T, 7U, 7V) | spmne Fuse | |||
| PCHU-21-37 | 74LS161A 4-Bit Binary Counters | (6H, 6, 6K, 6L, 6M, 4R) | oe: | ls Le] | ||
| PCHU-21-38 | 74LS164 8-Bit Shift Registers | (8H, 5Q) | ei}o | eS | ||
| PCHU-21-39 | 74LS165A 8-Bit Shift Registers | (8A, 8B) | poner | i | Os | |
| PCHU-21-40 | 74LS175 Quad “D” Flip-Flops (CL) | (48) | song ot | |||
| PCHU-21-41 | _74LS194A 4-Bit Shift Registers | (6Q, 6R) | (| | os | oT | |
| PCHU-21-42 | 74LS240 Octal Bus Inverters (TS) | (7A, 7B, 7C) | Le | |||
| PCHU-21-43 | 74LS244 Octal Buffers & Line Drivers (TS) | “ | 01 | |||
| (IL, 2M, 3M, 88, 5V, 6V) | 1 | ro | SY | |||
| PCHU-21-44 | _74LS245 Octal Bus Transceivers (TS) | (1K, 6Z) | — | “ | 3 | |
| PCHU-21-45 | 74LS259 8-Bit Addressable Latches | (7D, 7E) | |__ 70: | "Baan | | es | |
| PCHU-21-46 | —74LS299 8-Bit Shift/Storage Registers | (7L, 7N, 7Q) | : | _e | = | a |
| PCHU-21-47 | = 74LS367A Hex Bus Drivers | (4L) | osu sa ust | vote | ae en | ™ |
| PCHU-21-48 | 74LS368A Hex Bus Drivers | (8E, 8F, 5S) | ; | Fuse (Sow Bow) 3A, 128v—| | vi (~) (~) TL | ral | |
| PCHU-21-49 | 74HC373 Ocial “D” Transparent Latches C-MOS_ (3K) | a | ||||
| PCHU-21-50 | 74LS377 Octal “D” Flip-Flops | (6P) | Fuse (Slow Blow) 2.54, 125V | |||
| PCHU-21-51 | 74S04 Hex Inverters | (2G, 6N) | ||||
| PCHU-21-52 | 7437 Quad 2-Input NAND Buffers | (4X) | Fig. 6 | Video Monitor : [Y51 Type] XM-2001N | ||
| PCHU-21-53 | 75471 Dual Peripheral AND Drivers | (6C) | ||||
| PCHU-21-54 — 74HC10 Triple 3-Input NAND C-MOS | (8Y) | WARNING | ||||
| PCHU-21-55 | PST518A Low Voltage Detector | (72) | a | . | . | |
| PCHU-21-56 | _LM324 Quad Operational Amplifiers | (3E) | Do not touch the inside of the Video Monitor. | |||
| PCHU-21-57. | LM3900 Quad Operational Amplifiers | (1) | 't contains many parts supplied with high voltage. | |||
| PCHU-21-58 | CD 4066 Quad Analog Switches C-MOS | (3C, 2E) |
23 6
- Option Switch Settings
A pair of Option Toggle Switches are mounted on the Game PCB.
PCH1-CPU PCB
Fig. 7 » o oO G m
io} I = BEBE}: dONWTYF I cMSm m Z
Option Toggle Switches B. PCH1-UP Operation Panel Assembly : PARTS LIST
ITEM PART No. DESCRIPTION MDST-14-12 A8 Control Lever Assembly TNX-23-18 8 way Guide Plate TKGU-23-23 E Ring 4 TKGU-23-21 Switch Collar
TKGU-23-20 Spring Stopper TKGU-23-13 Micro-switch VL12L (Bent) (8 Required) TKGU-23-17 Switch Spacer (8 Required)
| 5 | TKGU-23-22 | Lever Spring |
TKGU-23-16 Bearing Bracket
| 10 | TMAU-12-15 | Lever Plate |
| an} | TMAU-12-14 | Control Knob Plate 28D |
| 12 | TMAU-12-16 | Controller Knob Collar 8L |
| 13 | TMAU-11-18 | Knob with Shaft 80.5L |
| 14 | TKGU-23-34 | Pal Nut (4 Required) |
| 15 | TKGU-23-26 | Nut Plate (4 Required) |
| 16 | TKGU-23-12 | Switch Button Bracket (4 Required) |
| 17 | TMAU-34-18 | Micro-switch VL12L (Straight) |
| 18 | TMAU-12-18 | Collar 34x28x7H (4 Required) |
| 19 | TMAU-11-19 | Operation Panel Fastener B 38W (2 Required) |
| 20 | CHPU-12-17 | Black Sponge 2x20x590L |
| 21 | PCHU-12-11 | PCH Operation Panel |
| 22 | MDSU-12-07 | Button Assembly (Red) (2 Required) |
| 23 | MDST-12-21 | Button Assembly (Black) (2 Required) |
| 24 | MDSA-23-29 | Switch Collar (5 Required) |
| 25 | MDSA-23-30 . | Switch Bezel (5 Required) |
| 26 | MDSA-23-31 | Switch P163C3RU Red (2 Required) |
| 27 | MDSA-23-32 | Switch P163C3RU Black (3 Required) |
C. PCH1-UP Wiring Harnesses
PART No. DESCRIPTION See Fig. 16 CHPU-41-16 UP 56P 054 Edge Connecting Harness TPPU-93-02 2P-400 Audio Harness (400mm) (2 Required) TPPU-93-07 6P-600 Video Harness (600mm) (2 Required) TMAU-41-12 3P-500 Game Counter Harness (500mm) CHPU-41-13 4P-800 Service Switch Harness (800mm) TMAU-41-14 AP-600 WL Coin Harness (600mm) TKGU-13-17 2P Speaker Harness [2P-860] (860mm) (2 Required) CHVU-41-11 3P-1500 TV Extension Power Cord UL (2 Required) MDSU-41-11 UP 15P 062 SW Harness PCHU-41-11 UP 12P 079 SW Harness PCHU-41-15 UP 20P 079 Gun-Main Harness PCHU-41-16 20P-30 FCC Flat Cable
B. PCH1-UP Operation Panel Assembly A. Game Settings
All the Option Switch Settings MUST be done with Power Off.
Fig. 8 Game Settings SW1 Toggle Settings G H Attract music ON ON * OFF OFF Self-Test/Game Game OFF * Self-Test ON Factory Settings
STANDARD TIME (no bonus)
2K kK kK KK
No Prime Time
Toggle Settings
ddd A B Cc D E F
1: A8 Control Toggle A-Toggie F must be “OFF” OFF OFF OFF OFF OFF OFF | : ontro H
Lever Assembly Seconds per Coin
sw2 Toggle Settings —_——_ Play Time/Coin 1 J K L M N o | Pp | Free Play OFF OFF OFF OFF OFF OFF OFF ON 4min. 50sec. OFF ON ON ON ON ON ON ON 40sec. OFF OFF ON ON ON ON ON ON 30sec. OFF ON OFF ON ON ON ON ON | 20sec, OFF OFF OFF ON ON ON ON ON 10sec. OFF ON ON OFF ON ON ON ON 4min. OFF OFF ON OFF ON ON ON ON 3min. 50sec. OFF ON OFF OFF ON ON ON ON | 40sec, OFF OFF OFF OFF ON 30sec. OFF ON ON ON 20sec. OFF OFF ON ON 10sec. OFF ON OFF ON 3min. OFF OFF OFF ON 2min, 50sec. OFF ON ON OFF 40sec. OFF OFF ON OFF 30sec. OFF ON OFF OFF 20sec. OFF OFF OFF OFF 10sec. OFF ON ON ON 2min. OFF OFF ON ON
28K OK OK KK Fig. 19 Operation Panel Assembly
21 8-1
PRIME TIME (bonus) for 2 COINS A. PCH1-UP Game Cabinet Assembly : PARTS LIST
| When using PRIME TIME (bonus) for 2 COINS, both SW1 | ITEM | PART No. | DESCRIPTION |
and SW2 must be adjusted for proper game operation
| 1 | TKGU-01-61 | Vent Grill (2 Required) | ||||
| 8 ok ok 2k 2k He | 2 | CHPU-13-15 | Back Door | |||
| . | . | 3 | TMAU-14-14 | Lock K6510 | ||
| Prime Time bonus % | 4 | TMAU-11-15 | Cam A | |||
| PRIME TIME | TOTAL | Toggle Settings | 5 | CHPU-11-18 | PCB Stopper (2 Required) | ||
| swt | conus «| PRMEIMEL | “a | TB ] co | > | EF | 6 | PCHU-21-01 | PCH1-CPU Complete PCB Assembly |
| 8% | 650 | ON | |ON|ON) OFF OFF | OFF | 7 | PCHU-24-01 | PCH1-ROM Complete PCB Assembly :Order By Game Name |
| Bippleyed of Video’ Monitor | 17% | 700 | OFF | OFF OFF | ON OFF | OFF | 8 | PCHU-11-14 | 079 Shield Cover | |
| as follows : | 25% | 750 | ON | OFF] OFF |ON | OFF | OFF | 9 | CHPU-23-01 | 054-FCC Complete PCB Assembly | |
| : | 10 | CHPU-11-17 | 054 Shield Spacer (2 Required) | |||
| Regular Time | 83% | 800_| | OFF | OFF | OFF | OFF | ON | OFF | ra | CHPU-23-35 | Nylatch Fastener (8 Required) |
| 1 COIN = 300 | 42% | 850 | ON | OFF | OFF | OFF | ON | OFF | 12 | CHPU-23-34 | Nylatch Grommet (8 Required) | |
| PRIME TIME | |___80% | 900 | OFF | ON | OFF Orr {ON | et | 43. | PCHU-23-01 | 079-FCC Complete PCB Assembly |
| 2 cons ~ 8%. | 58% | 850 | ON | ON | OFF | OFF | ON | OFF | 14 | TKGU-01-08 | Power Cord: Order By Voltage & Plug Type | |
| 67% | 1000_ | OFF | OFF | ON | OFF | ON | OFF | 15 | CHPU-88-01 | PP-1000A Complete Power Supply Assembly | ||
| 75% | 1050 | ON | OFF | ON | OFF | ON | OFF | 16 | CHPU-08-01 | PT-1021A Power Transformer (For 90~120V) | ||
| 83% | 1100 | OFF | ON | ON | OFF | ON | OFF | 16 | CHPU-18-01 | PT-1021B Power Transformer (For 90~120V) | ||
| 92% | 1150 | ON | ON | ON | OFF | ON | OFF | 16 | CHPU-18-02 | PT-1022B Power Transformer (For 200~240V) | ||
| 100% | 1200 | OFF | OFF | OFF | ON | ON | OFF | 17 | TKGU-01-30 | Caster (2 Required) | ||
| | | 18 | CHPU-01-01-10 | 054 Shield Cage | |||
| EXAMPLE. Displayed as | Regular Time 1 COIN -300(3min) | 19 | TKGU-01-65 | Strain Relief Bushing Plate | |||
| PRIME TIME 2 COINS--Gooeminy | 20. | TKGU-01-10 | Strain Relief Bushing |
Toggle A- OFF, B- OFF, C= OFF, D- ON, E=OFF, F-OFF, |=OFF, J= OFF, K= OFF, L=-ON, M-OFF, N-ON, O- OFF, P=ON
Seconds per Coin
| sw2 | ] | Toggle Settings | |||||
| Play Time/Coin (sec) | I | J | kK |o- | M | N | fo) | Pp |
Amin. (240) | OFF | OFF | ON | OFF | ON | ON | OFF | ON
| 38min. 50sec. (230) | OFF | ON | OFF | OFF | ON | ON | OFF | ON | ||
| 40sec. (220) | OFF | OFF | OFF | OFF | ON | ON | OFF | ON | ||
| 30sec. (210) | OFF | ON | ON | ON | OFF | ON | OFF | ON | ||
| 20sec. (200) | OFF | OFF | ON | ON | OFF | ON | OFF | ON | ||
| 10sec. (190) | OFF | ON | OFF | ON | OFF | ON | OFF | ON | ||
| F | 3min. | (180) | OFF | OFF | OFF | ON | OFF | ON | OFF | ON |
| 2min. 50sec. (170) | OFF | ON | ON | OFF | OFF | ON | OFF | ON | ||
| 40sec. (160) | OFF | OFF | ON | OFF | OFF | ON | OFF | ON | ||
| | | 30sec. (150) | OFF | ON | OFF | OFF | OFF | ON | OFF | ON | |
| 20sec. (140) | OFF | OFF | OFF | OFF | OFF | ON | OFF | ON | ||
| 10sec. (130) | OFF | ON | ON | ON | ON | OFF | OFF | ON | ||
| 2min. | (120) | OFF | OFF | ON | ON | ON | OFF | OFF | fe} n | |
+ Factory Settings 28 OK ok ok ok OK ok
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
- Self-Test and Bookkeeping
- Entry There are three ways to enter Self-Test and Bookkeeping modes.
- Press the Service Switch and Enter Button simultaneously during Attract Mode or Game Mode.
(bo) Start with game in Off position. While pressing the Service Switch, set the Power On/Off Switch to the “On” position. Through this entry, you have an option to reset the Bookkeeping RAM. Follow the instruction on the Video Monitor.
- Start with game in Off position. Set Toggle H (SW1) on the Game PCB to on position. And set the Power On/Off Switch to the “On” position.
- Self-Test and Bookkeeping are self-explanatory on the Video Monitor as follows.
Fig. 9 Self-Test and Bookkeeping
RAM TEST pane —________+ gy OK ~—————— Passed location F NG =«———__——Failed on the PCB Bw
(CPU PCB)
ROM TEST Example 8T OK ~————-_——— Passed ROM location on the PCB (CPU PCB)
“HOW OFTEN HAVE THE GAMES BEEN ACCESSED?”
| 1. Game Title A | 48 | Frequency Accessed |
Example | Joe |
| Bookkeeping | 5.( Game Title E —— | 125 | | | The Most Accessed |
| 10. Game Title J | a | The Least Accessed |
A. PCH1-UP Game Cabinet Assembly : PARTS LIST Continued
ITEM PART No. DESCRIPTION
| 1 | CHPU-13-03 | Body (Wooden Game Cabinet) | |
| 2 | TKGU-01-29 | Fluorescent Lamp Ass’y. | |
| 3 | CHPU-11-19 | Name Plate Retainer Upper 598L | |
| 4 | PCHU-12-12 | PCH Display Panel | (Name Plate) |
| 5 | CHPU-11-11 | Name Plate Retainer Lower 598L | |
| 6 | TPPU-20-00 | Video Monitor [32 Type] 20-EZV (R-C) |
Video Monitor [33 Type] 20-EZV (R-C) Video Monitor [35 Type] 20-Z2AW
| 6 | MDSU-33-01 | Video Monitor [Y51 Type] XM-2001N | |
| 7 | CHPU-11-10 | Front Screen Retainer 598L | |
| 8 | CHPU-13-01 | 054 Black Cardboard Bezel Upper | |
| 9 | CHPU-13-02 | 054 Black Cardboard Bezel Lower | |
| 10 | CHPU-12-13 | CHP-US Front Screen | |
| 1 | PCHU-12-11 | PCH Operation Panel | (Panel Only) |
| 12 | TKGU-01-49 | Speaker Grill (2 Required) | |
| 13 | TKGU-01-43 | Speaker (2 Required) | |
| 14 | TKGU-01-31 | Operation Panel Clamp A (2 Required) | |
| 15 | TMAU-11-20 | CS Plate 120W | |
| 16 | TKGU-01-33 | Service Switch (with Button) | |
| 17 | TKGU-01-11 | Game Counter | |
| 18 | TMAU-14-17 | Service Door ADD-S2: Order By Currency | |
| 19 | TMAU-14-18 | Coin Selector: Order By Currency | |
| 20 | TMAU-34-17 | Lamp BA-9S 6.3V 0.15A | |
| 21 | TMAU-34-16 | Lamp Socket BA-9S | |
| 22 | TMAU-34-19 | Micro-switch ADD D2MC-5F1 | |
| 23 | TMAU-14-12 | Door Lock | |
| 24 | TMAU-11-14 | Cam B31R (2 Required) | |
| 25 | TMAU-14-11 | Cash Door ADD | |
| 26 | TMAU-11-27 | Cash Box ADD | |
| 27 | MDSG2-02-01 | 062G2 Gun Assembly | |
| 28 | PCHU-11-12 | 079 Gun Holster Base | |
| 29 | MDSG2-12-19 | Gun Holster | |
| 30 | MDSG2-11-22 | Gun Holster Plate | |
| 31 | MDSG2-51-19 | Button Bolt (6 Required) |
- Parts Lists
A. PCH1-UP Game Cabinet Assembly
17 Front View of Game Cabinet
- Maintenance and Repair
A. Fuse Replacement This game contains 4 fuses. Replace fuses only with the same type as listed below.
Fig. 10 Specification of Fuses
- Main Fuse U.S. : 5A 125V ( 90~120V) Europe : 3A 250V (200~240V) See Fig. 1 and 3
- Power Supply Fuse 3A 125V (Midget) See Fig. 3
- Video Monitor Fuses
- [82 Type] 20-EZV(R-C) 4A 125V(Slow Blow)
- [83 Type] 20-EZV(R-C) > 0.3A 125V(Midget)
- [85 Type] 20-Z2AW See Fig. 5
- [Y51 Type] XM-2001N_ 2.5A 125V(Slow Blow) 3A 125V(Slow Blow) See Fig. 6
B. Cleaning The exterior of the game, all metal parts and all plastic parts can be cleaned with a nonabrasive cleanser. You should be careful when cleaning the glass or plastic parts. A dry cloth may cause scratches which will result in a foggy appearance.
C. Operation Panel
- Operation Panel Removal Before repairing or replacing any switches or A8 Control Lever Assembly 0n the Operation Panel, unplug the game. Open the Service Door, which are reach through the opening, and unlock the Clamps, located at each end onthe underside of the Operation Panel. See Fig. 13.
- Micro-switch Replacement Whenever you replace any micro-switch on the Operation Panel, a switch gap adjustment is needed as shown in Fig. 11. Also, see Fig. 19 for layout of Control Panel Switches.
Press
Switch Button Assy.
Micro-switch
Gap:0.2~0.5mm(1/128 ~ 5/256 inch) / :
Fig. 11 Switch gap adjustment
- Lubrication for A8 Control Lever Assembly To maintain the A8 Control Lever Assembly in good condition, lubricate the pillow balls and 8 way Guide Plate approx. every 3 months. See Fig. 12.
Lubricate here//
Fig. 12 Lubrication points Eower Transiormer
1200r240¥ ; nodor226V1 Power Switch Power Supply SIF ono
| PP - 10008 | 2 | 1 | gg use | |||
| 12P Ol | 9P OUT | ' | W=120V 5A | | |||
| osesee | geo | Pad | i | 200V-240V3A ! | ||
| 55550 e | S55 | PY | ‘ | ! | ||
| i | a | jj | 1 | 7 | 4 | 1 |
1 f23yeTs [67 Ja(s fof 142)3]4]5]6]7, H ] ow oO {it}
| lel | glx] | s| | 18 | Ie} | gy | |
| ¢|elal>|21s | FA | ej] & | H | ||
| UP S6P 054 Edge | $e) SiS ella | elgg] | 215) | = | ' |
| Connecting | 5 ajalol S15 | alto] | ae Fd | ‘ | |
| Harness | [|| | L.---------..-- | MOOL |
PT-1021A ( 90~120V) 228 (20 y PT-10218(90-120V)
Upper Mo! [WARNING This receptacte for use with nitor only
3P-1500 Power Cord =CE fo
TV Extension Power Cord UL
Fluores: 3P-1500 bd
TV Extension Power Cord UL_black cent Lamp 10W black,
Harness 3P-500 Game Counter
lorange p— orange brown FH brown
(Remarks)
connector Mark(R) means that olor is red. AP - 800. Service Switch Harness (R) yellow. [474] ° EJEI| service [IZ] brown Switch
Shield: On, ing Wire brown red ‘orange Shield
uP
PCH Operation Panel ing Wire
i é
15P 062 SW Harness Reset Start 2.4 Button 2.8 Butcon be ed yellow.
6P- 600 . Video Harness +
brown 2P -400 Audio Harness Video Monitor
white Hib red
2P - 860,
100v
ACIN
Frame GND
Video Monitor
Speaker Harness Speaker “Upper Video Monitor
‘ower Video Monitor white white Speaker
2P-860
Wiring and Connection
CPU PCB PCH1-CPU
cH
ROM PCB lPcH1-ROM
ROM PCB [i TM [2 1 MCr TMBLU |
[7 [seus [8 [sv GNo | [9 TS "Syne |
20P.30 FCC Flat Cable Fig.
079-FCC PCB Lis | [207 }2i] 122]
[24] [25} [26] [27] {28} [29] [30] [31] [32] [33] [34] [35 | 136}
[38 | [39] [40] 16 Wiring and Connection
[Down a [GNo_"}
[cr serect_} [Enter Enter SEEREEEEREEEEHEeEERF (Remarks) Mark(R) means that connector color is red.
UP_20P 079 Gun-Main Harness
Gun Assembly fee D. Video Monitor Removal
(1) Front Screen Removal First remove the Operation Panel and then pull the Front Screen
toward you.
Front Screen
Operation Panel Ass’y.
Service Door
Fig. Clamp
Front Screen and Operation Panel Ass’y. Removal
Fig.
- Video Monitor Removal lf you need to remove the Video Monitor, follow the instructions listed below. But the following procedure should only be performed by an experienced service technician
It is recommended the game be left unplugged for at least one hour before removing the Video Monitor. This will probably discharge the CRT, but extreme caution is still necessary.
- Make sure game is unplugged !!
- Open the Rear Door Panel and remove the Front Screen.
- Unplug all the harnesses and cables from the Video Monitor.
- Standing at the front opening of the game, remove the four mounting bolts and flat washers. See Fig. 14.
- Carefully lift the Video Monitor and pull toward you.
Use extreme caution and do not touch electrical parts of the yoke area with your hands or with any metal object in your hands.
Remove the four mounting bolts and flat washers Fastener : (0° E. Game PCB Removal and ROM PCB Exchange
- Make sure the Power On/Off Switch is “Off” position!!
- Open the Back Door.
- Before removing Game PCB or exchanging ROM PCB, discharge your static electricity by touching Shield Cage with your hand.
- Remove the 56-pin edge connector from the right side of the 054-FCC PCB on the 079 Shield Cover Ass’y. (€) Pull out 6 Fasteners located on perimeter of the 079 Shield Cover. See Fig. 15.
- Remove the Game PCB from the Shield Cage by carefully sliding it straight out of the wooden slots in the Shield Cage.
oe : Lay PCB | C) flat on table | with 079 Shield | IML Cover hanging CWO \\ DCW? off table as LPs x shown. | 054-FCC PCB ett
Fig. 15 079 Shield Cover
Game PCB Removal and ROM PCB Exchange
A reversed connector will damage your PCB! If the connectors don't slip on easily, don't force them !
- Radio Frequency Interference (RFI)
In order to protect against the RFI radiated from this equipment, please comply with the following.
- Do not use non-Nintendo parts !
- Do not modify your game circuitry ! ) Do not modify the wiring harness and connections !
- Connect this game only to a grounded 3-wire outlet.
- After servicing the Game PCB, shut the 079 Shield Cover completely with the Fasteners. See Fig. 15. ( (c
Fig.
- Video Monitor Removal lf you need to remove the Video Monitor, follow the instructions listed below. But the following procedure should only be performed by an experienced service technician
It is recommended the game be left unplugged for at least one hour before removing the Video Monitor. This will probably discharge the CRT, but extreme caution is still necessary.
- Make sure game is unplugged !!
- Open the Rear Door Panel and remove the Front Screen.
- Unplug all the harnesses and cables from the Video Monitor.
- Standing at the front opening of the game, remove the four mounting bolts and flat washers. See Fig. 14.
- Carefully lift the Video Monitor and pull toward you.
Use extreme caution and do not touch electrical parts of the yoke area with your hands or with any metal object in your hands.
Remove the four mounting bolts and flat washers Fastener : (0° E. Game PCB Removal and ROM PCB Exchange
- Make sure the Power On/Off Switch is “Off” position!!
- Open the Back Door.
- Before removing Game PCB or exchanging ROM PCB, discharge your static electricity by touching Shield Cage with your hand.
- Remove the 56-pin edge connector from the right side of the 054-FCC PCB on the 079 Shield Cover Ass’y. (€) Pull out 6 Fasteners located on perimeter of the 079 Shield Cover. See Fig. 15.
- Remove the Game PCB from the Shield Cage by carefully sliding it straight out of the wooden slots in the Shield Cage.
oe : Lay PCB | C) flat on table | with 079 Shield | IML Cover hanging CWO \\ DCW? off table as LPs x shown. | 054-FCC PCB ett
Fig. 15 079 Shield Cover
Game PCB Removal and ROM PCB Exchange
A reversed connector will damage your PCB! If the connectors don't slip on easily, don't force them !
- Radio Frequency Interference (RFI)
In order to protect against the RFI radiated from this equipment, please comply with the following.
- Do not use non-Nintendo parts !
- Do not modify your game circuitry ! ) Do not modify the wiring harness and connections !
- Connect this game only to a grounded 3-wire outlet.
- After servicing the Game PCB, shut the 079 Shield Cover completely with the Fasteners. See Fig. 15. ( (c
Wiring and Connection
CPU PCB PCH1-CPU
cH
ROM PCB lPcH1-ROM
ROM PCB [i TM [2 1 MCr TMBLU |
[7 [seus [8 [sv GNo | [9 TS "Syne |
20P.30 FCC Flat Cable Fig.
079-FCC PCB Lis | [207 }2i] 122]
[24] [25} [26] [27] {28} [29] [30] [31] [32] [33] [34] [35 | 136}
[38 | [39] [40] 16 Wiring and Connection
[Down a [GNo_"}
[cr serect_} [Enter Enter SEEREEEEREEEEHEeEERF (Remarks) Mark(R) means that connector color is red.
UP_20P 079 Gun-Main Harness
Gun Assembly fee D. Video Monitor Removal
(1) Front Screen Removal First remove the Operation Panel and then pull the Front Screen
toward you.
Front Screen
Operation Panel Ass’y.
Service Door
Fig. Clamp
Front Screen and Operation Panel Ass’y. Removal
Press
Switch Button Assy.
Micro-switch
Gap:0.2~0.5mm(1/128 ~ 5/256 inch) / :
Fig. 11 Switch gap adjustment
- Lubrication for A8 Control Lever Assembly To maintain the A8 Control Lever Assembly in good condition, lubricate the pillow balls and 8 way Guide Plate approx. every 3 months. See Fig. 12.
Lubricate here//
Fig. 12 Lubrication points Eower Transiormer
1200r240¥ ; nodor226V1 Power Switch Power Supply SIF ono
| PP - 10008 | 2 | 1 | gg use | |||
| 12P Ol | 9P OUT | ' | W=120V 5A | | |||
| osesee | geo | Pad | i | 200V-240V3A ! | ||
| 55550 e | S55 | PY | ‘ | ! | ||
| i | a | jj | 1 | 7 | 4 | 1 |
1 f23yeTs [67 Ja(s fof 142)3]4]5]6]7, H ] ow oO {it}
| lel | glx] | s| | 18 | Ie} | gy | |
| ¢|elal>|21s | FA | ej] & | H | ||
| UP S6P 054 Edge | $e) SiS ella | elgg] | 215) | = | ' |
| Connecting | 5 ajalol S15 | alto] | ae Fd | ‘ | |
| Harness | [|| | L.---------..-- | MOOL |
PT-1021A ( 90~120V) 228 (20 y PT-10218(90-120V)
Upper Mo! [WARNING This receptacte for use with nitor only
3P-1500 Power Cord =CE fo
TV Extension Power Cord UL
Fluores: 3P-1500 bd
TV Extension Power Cord UL_black cent Lamp 10W black,
Harness 3P-500 Game Counter
lorange p— orange brown FH brown
(Remarks)
connector Mark(R) means that olor is red. AP - 800. Service Switch Harness (R) yellow. [474] ° EJEI| service [IZ] brown Switch
Shield: On, ing Wire brown red ‘orange Shield
uP
PCH Operation Panel ing Wire
i é
15P 062 SW Harness Reset Start 2.4 Button 2.8 Butcon be ed yellow.
6P- 600 . Video Harness +
brown 2P -400 Audio Harness Video Monitor
white Hib red
2P - 860,
100v
ACIN
Frame GND
Video Monitor
Speaker Harness Speaker “Upper Video Monitor
‘ower Video Monitor white white Speaker
2P-860
- Parts Lists
A. PCH1-UP Game Cabinet Assembly
17 Front View of Game Cabinet
- Maintenance and Repair
A. Fuse Replacement This game contains 4 fuses. Replace fuses only with the same type as listed below.
Fig. 10 Specification of Fuses
- Main Fuse U.S. : 5A 125V ( 90~120V) Europe : 3A 250V (200~240V) See Fig. 1 and 3
- Power Supply Fuse 3A 125V (Midget) See Fig. 3
- Video Monitor Fuses
- [82 Type] 20-EZV(R-C) 4A 125V(Slow Blow)
- [83 Type] 20-EZV(R-C) > 0.3A 125V(Midget)
- [85 Type] 20-Z2AW See Fig. 5
- [Y51 Type] XM-2001N_ 2.5A 125V(Slow Blow) 3A 125V(Slow Blow) See Fig. 6
B. Cleaning The exterior of the game, all metal parts and all plastic parts can be cleaned with a nonabrasive cleanser. You should be careful when cleaning the glass or plastic parts. A dry cloth may cause scratches which will result in a foggy appearance.
C. Operation Panel
- Operation Panel Removal Before repairing or replacing any switches or A8 Control Lever Assembly 0n the Operation Panel, unplug the game. Open the Service Door, which are reach through the opening, and unlock the Clamps, located at each end onthe underside of the Operation Panel. See Fig. 13.
- Micro-switch Replacement Whenever you replace any micro-switch on the Operation Panel, a switch gap adjustment is needed as shown in Fig. 11. Also, see Fig. 19 for layout of Control Panel Switches.
- Self-Test and Bookkeeping
- Entry There are three ways to enter Self-Test and Bookkeeping modes.
- Press the Service Switch and Enter Button simultaneously during Attract Mode or Game Mode.
(bo) Start with game in Off position. While pressing the Service Switch, set the Power On/Off Switch to the “On” position. Through this entry, you have an option to reset the Bookkeeping RAM. Follow the instruction on the Video Monitor.
- Start with game in Off position. Set Toggle H (SW1) on the Game PCB to on position. And set the Power On/Off Switch to the “On” position.
- Self-Test and Bookkeeping are self-explanatory on the Video Monitor as follows.
Fig. 9 Self-Test and Bookkeeping
RAM TEST pane —________+ gy OK ~—————— Passed location F NG =«———__——Failed on the PCB Bw
(CPU PCB)
ROM TEST Example 8T OK ~————-_——— Passed ROM location on the PCB (CPU PCB)
“HOW OFTEN HAVE THE GAMES BEEN ACCESSED?”
| 1. Game Title A | 48 | Frequency Accessed |
Example | Joe |
| Bookkeeping | 5.( Game Title E —— | 125 | | | The Most Accessed |
| 10. Game Title J | a | The Least Accessed |
A. PCH1-UP Game Cabinet Assembly : PARTS LIST Continued
ITEM PART No. DESCRIPTION
| 1 | CHPU-13-03 | Body (Wooden Game Cabinet) | |
| 2 | TKGU-01-29 | Fluorescent Lamp Ass’y. | |
| 3 | CHPU-11-19 | Name Plate Retainer Upper 598L | |
| 4 | PCHU-12-12 | PCH Display Panel | (Name Plate) |
| 5 | CHPU-11-11 | Name Plate Retainer Lower 598L | |
| 6 | TPPU-20-00 | Video Monitor [32 Type] 20-EZV (R-C) |
Video Monitor [33 Type] 20-EZV (R-C) Video Monitor [35 Type] 20-Z2AW
| 6 | MDSU-33-01 | Video Monitor [Y51 Type] XM-2001N | |
| 7 | CHPU-11-10 | Front Screen Retainer 598L | |
| 8 | CHPU-13-01 | 054 Black Cardboard Bezel Upper | |
| 9 | CHPU-13-02 | 054 Black Cardboard Bezel Lower | |
| 10 | CHPU-12-13 | CHP-US Front Screen | |
| 1 | PCHU-12-11 | PCH Operation Panel | (Panel Only) |
| 12 | TKGU-01-49 | Speaker Grill (2 Required) | |
| 13 | TKGU-01-43 | Speaker (2 Required) | |
| 14 | TKGU-01-31 | Operation Panel Clamp A (2 Required) | |
| 15 | TMAU-11-20 | CS Plate 120W | |
| 16 | TKGU-01-33 | Service Switch (with Button) | |
| 17 | TKGU-01-11 | Game Counter | |
| 18 | TMAU-14-17 | Service Door ADD-S2: Order By Currency | |
| 19 | TMAU-14-18 | Coin Selector: Order By Currency | |
| 20 | TMAU-34-17 | Lamp BA-9S 6.3V 0.15A | |
| 21 | TMAU-34-16 | Lamp Socket BA-9S | |
| 22 | TMAU-34-19 | Micro-switch ADD D2MC-5F1 | |
| 23 | TMAU-14-12 | Door Lock | |
| 24 | TMAU-11-14 | Cam B31R (2 Required) | |
| 25 | TMAU-14-11 | Cash Door ADD | |
| 26 | TMAU-11-27 | Cash Box ADD | |
| 27 | MDSG2-02-01 | 062G2 Gun Assembly | |
| 28 | PCHU-11-12 | 079 Gun Holster Base | |
| 29 | MDSG2-12-19 | Gun Holster | |
| 30 | MDSG2-11-22 | Gun Holster Plate | |
| 31 | MDSG2-51-19 | Button Bolt (6 Required) |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
PRIME TIME (bonus) for 2 COINS A. PCH1-UP Game Cabinet Assembly : PARTS LIST
| When using PRIME TIME (bonus) for 2 COINS, both SW1 | ITEM | PART No. | DESCRIPTION |
and SW2 must be adjusted for proper game operation
| 1 | TKGU-01-61 | Vent Grill (2 Required) | ||||
| 8 ok ok 2k 2k He | 2 | CHPU-13-15 | Back Door | |||
| . | . | 3 | TMAU-14-14 | Lock K6510 | ||
| Prime Time bonus % | 4 | TMAU-11-15 | Cam A | |||
| PRIME TIME | TOTAL | Toggle Settings | 5 | CHPU-11-18 | PCB Stopper (2 Required) | ||
| swt | conus «| PRMEIMEL | “a | TB ] co | > | EF | 6 | PCHU-21-01 | PCH1-CPU Complete PCB Assembly |
| 8% | 650 | ON | |ON|ON) OFF OFF | OFF | 7 | PCHU-24-01 | PCH1-ROM Complete PCB Assembly :Order By Game Name |
| Bippleyed of Video’ Monitor | 17% | 700 | OFF | OFF OFF | ON OFF | OFF | 8 | PCHU-11-14 | 079 Shield Cover | |
| as follows : | 25% | 750 | ON | OFF] OFF |ON | OFF | OFF | 9 | CHPU-23-01 | 054-FCC Complete PCB Assembly | |
| : | 10 | CHPU-11-17 | 054 Shield Spacer (2 Required) | |||
| Regular Time | 83% | 800_| | OFF | OFF | OFF | OFF | ON | OFF | ra | CHPU-23-35 | Nylatch Fastener (8 Required) |
| 1 COIN = 300 | 42% | 850 | ON | OFF | OFF | OFF | ON | OFF | 12 | CHPU-23-34 | Nylatch Grommet (8 Required) | |
| PRIME TIME | |___80% | 900 | OFF | ON | OFF Orr {ON | et | 43. | PCHU-23-01 | 079-FCC Complete PCB Assembly |
| 2 cons ~ 8%. | 58% | 850 | ON | ON | OFF | OFF | ON | OFF | 14 | TKGU-01-08 | Power Cord: Order By Voltage & Plug Type | |
| 67% | 1000_ | OFF | OFF | ON | OFF | ON | OFF | 15 | CHPU-88-01 | PP-1000A Complete Power Supply Assembly | ||
| 75% | 1050 | ON | OFF | ON | OFF | ON | OFF | 16 | CHPU-08-01 | PT-1021A Power Transformer (For 90~120V) | ||
| 83% | 1100 | OFF | ON | ON | OFF | ON | OFF | 16 | CHPU-18-01 | PT-1021B Power Transformer (For 90~120V) | ||
| 92% | 1150 | ON | ON | ON | OFF | ON | OFF | 16 | CHPU-18-02 | PT-1022B Power Transformer (For 200~240V) | ||
| 100% | 1200 | OFF | OFF | OFF | ON | ON | OFF | 17 | TKGU-01-30 | Caster (2 Required) | ||
| | | 18 | CHPU-01-01-10 | 054 Shield Cage | |||
| EXAMPLE. Displayed as | Regular Time 1 COIN -300(3min) | 19 | TKGU-01-65 | Strain Relief Bushing Plate | |||
| PRIME TIME 2 COINS--Gooeminy | 20. | TKGU-01-10 | Strain Relief Bushing |
Toggle A- OFF, B- OFF, C= OFF, D- ON, E=OFF, F-OFF, |=OFF, J= OFF, K= OFF, L=-ON, M-OFF, N-ON, O- OFF, P=ON
Seconds per Coin
| sw2 | ] | Toggle Settings | |||||
| Play Time/Coin (sec) | I | J | kK |o- | M | N | fo) | Pp |
Amin. (240) | OFF | OFF | ON | OFF | ON | ON | OFF | ON
| 38min. 50sec. (230) | OFF | ON | OFF | OFF | ON | ON | OFF | ON | ||
| 40sec. (220) | OFF | OFF | OFF | OFF | ON | ON | OFF | ON | ||
| 30sec. (210) | OFF | ON | ON | ON | OFF | ON | OFF | ON | ||
| 20sec. (200) | OFF | OFF | ON | ON | OFF | ON | OFF | ON | ||
| 10sec. (190) | OFF | ON | OFF | ON | OFF | ON | OFF | ON | ||
| F | 3min. | (180) | OFF | OFF | OFF | ON | OFF | ON | OFF | ON |
| 2min. 50sec. (170) | OFF | ON | ON | OFF | OFF | ON | OFF | ON | ||
| 40sec. (160) | OFF | OFF | ON | OFF | OFF | ON | OFF | ON | ||
| | | 30sec. (150) | OFF | ON | OFF | OFF | OFF | ON | OFF | ON | |
| 20sec. (140) | OFF | OFF | OFF | OFF | OFF | ON | OFF | ON | ||
| 10sec. (130) | OFF | ON | ON | ON | ON | OFF | OFF | ON | ||
| 2min. | (120) | OFF | OFF | ON | ON | ON | OFF | OFF | fe} n | |
+ Factory Settings 28 OK ok ok ok OK ok
B. PCH1-UP Operation Panel Assembly A. Game Settings
All the Option Switch Settings MUST be done with Power Off.
Fig. 8 Game Settings SW1 Toggle Settings G H Attract music ON ON * OFF OFF Self-Test/Game Game OFF * Self-Test ON Factory Settings
STANDARD TIME (no bonus)
2K kK kK KK
No Prime Time
Toggle Settings
ddd A B Cc D E F
1: A8 Control Toggle A-Toggie F must be “OFF” OFF OFF OFF OFF OFF OFF | : ontro H
Lever Assembly Seconds per Coin
sw2 Toggle Settings —_——_ Play Time/Coin 1 J K L M N o | Pp | Free Play OFF OFF OFF OFF OFF OFF OFF ON 4min. 50sec. OFF ON ON ON ON ON ON ON 40sec. OFF OFF ON ON ON ON ON ON 30sec. OFF ON OFF ON ON ON ON ON | 20sec, OFF OFF OFF ON ON ON ON ON 10sec. OFF ON ON OFF ON ON ON ON 4min. OFF OFF ON OFF ON ON ON ON 3min. 50sec. OFF ON OFF OFF ON ON ON ON | 40sec, OFF OFF OFF OFF ON 30sec. OFF ON ON ON 20sec. OFF OFF ON ON 10sec. OFF ON OFF ON 3min. OFF OFF OFF ON 2min, 50sec. OFF ON ON OFF 40sec. OFF OFF ON OFF 30sec. OFF ON OFF OFF 20sec. OFF OFF OFF OFF 10sec. OFF ON ON ON 2min. OFF OFF ON ON
28K OK OK KK Fig. 19 Operation Panel Assembly
21 8-1
- Option Switch Settings
A pair of Option Toggle Switches are mounted on the Game PCB.
PCH1-CPU PCB
Fig. 7 » o oO G m
io} I = BEBE}: dONWTYF I cMSm m Z
Option Toggle Switches B. PCH1-UP Operation Panel Assembly : PARTS LIST
ITEM PART No. DESCRIPTION MDST-14-12 A8 Control Lever Assembly TNX-23-18 8 way Guide Plate TKGU-23-23 E Ring 4 TKGU-23-21 Switch Collar
TKGU-23-20 Spring Stopper TKGU-23-13 Micro-switch VL12L (Bent) (8 Required) TKGU-23-17 Switch Spacer (8 Required)
| 5 | TKGU-23-22 | Lever Spring |
TKGU-23-16 Bearing Bracket
| 10 | TMAU-12-15 | Lever Plate |
| an} | TMAU-12-14 | Control Knob Plate 28D |
| 12 | TMAU-12-16 | Controller Knob Collar 8L |
| 13 | TMAU-11-18 | Knob with Shaft 80.5L |
| 14 | TKGU-23-34 | Pal Nut (4 Required) |
| 15 | TKGU-23-26 | Nut Plate (4 Required) |
| 16 | TKGU-23-12 | Switch Button Bracket (4 Required) |
| 17 | TMAU-34-18 | Micro-switch VL12L (Straight) |
| 18 | TMAU-12-18 | Collar 34x28x7H (4 Required) |
| 19 | TMAU-11-19 | Operation Panel Fastener B 38W (2 Required) |
| 20 | CHPU-12-17 | Black Sponge 2x20x590L |
| 21 | PCHU-12-11 | PCH Operation Panel |
| 22 | MDSU-12-07 | Button Assembly (Red) (2 Required) |
| 23 | MDST-12-21 | Button Assembly (Black) (2 Required) |
| 24 | MDSA-23-29 | Switch Collar (5 Required) |
| 25 | MDSA-23-30 . | Switch Bezel (5 Required) |
| 26 | MDSA-23-31 | Switch P163C3RU Red (2 Required) |
| 27 | MDSA-23-32 | Switch P163C3RU Black (3 Required) |
C. PCH1-UP Wiring Harnesses
PART No. DESCRIPTION See Fig. 16 CHPU-41-16 UP 56P 054 Edge Connecting Harness TPPU-93-02 2P-400 Audio Harness (400mm) (2 Required) TPPU-93-07 6P-600 Video Harness (600mm) (2 Required) TMAU-41-12 3P-500 Game Counter Harness (500mm) CHPU-41-13 4P-800 Service Switch Harness (800mm) TMAU-41-14 AP-600 WL Coin Harness (600mm) TKGU-13-17 2P Speaker Harness [2P-860] (860mm) (2 Required) CHVU-41-11 3P-1500 TV Extension Power Cord UL (2 Required) MDSU-41-11 UP 15P 062 SW Harness PCHU-41-11 UP 12P 079 SW Harness PCHU-41-15 UP 20P 079 Gun-Main Harness PCHU-41-16 20P-30 FCC Flat Cable
D. PCH1-CPU PCB Assembly : PARTS LIST Continued
- Video Monitor : [Y51 Type] XM-2001N PART No. DESCRIPTION (Reference Designations and Locations) PCHU-21-01 PCH1-CPU Complete PCB Assembly
| PCHU-21-11 | Z80A Microprocessor | (5X) | ||||
| PCHU-21-12 | RP2A03E Microprocessor | (1H) | ||||
| PCHU-21-13. | RP2CO3B PPU | (3H) | ||||
| PCHU-21-14. | 27128 16K-Byte EP-ROM 300ns PCH1-C-8T | (8T) | - | |||
| PCHU-21-15 | 2764 8K-Byte EP-ROM 300ns PCH1-C-8K | (8K) | | n= i POnur, | |||
| PCHU-21-16 | 2764 8K-Byte EP-ROM 300ns PCH1-C-8M | (8M) | Set to ‘Nogative” position! | |||
| PCHU-21-17 | 2764 8K-Byte EP-ROM 300ns PCH1-C-8P | (8P) | ||||
| PCHU-21-18 | = TMM2115BP-15 2K-Byte RAM 150ns | (2K) | ||||
| PCHU-21-19 — HM6116 ASP-20 2K-Byte RAM 200ns | (4K, 8R, 8V) | Positive | ||||
| PCHU-21-20 | TC5517 CPL-20 2K-Byte C-MOS RAM 200ns | (aW) | B | AE | & | |
| PCHU-21-21. | N82S129N 256x4-Bit Bipolar ROM PCH1-C-6D | (6D) | Bi | negate | a | |
| PCHU-21-22 | N82S129N 256x4-Bit Bipolar ROM PCH1-C-6E | (6E) | Mle | 2 | ||
| PCHU-21-23 | N82S129N 256x4-Bit Bipolar ROM PCH1-C-6F | (6F) | ean | |||
| PCHU-21-24 | 74LS00 Quad 2-Input NAND | (8J, 6U) | Grea | De | vio Sieh | |
| PCHU-21-25 | 74LS02 Quad 2-Input NOR | (4u) | DEGAUSS SWITCH | From P-800 | ||
| PCHU-21-26 | 74LS04 Hex Inverters | (8D, 3G, 8G, 5u, 7R, 7Y, 4Z) | HHOLD | Video Hames | ||
| PCHU-21-27 | 74LS08 Quad 2-Input AND | (7X) | vse | |||
| PCHU-21-28 | 74LS11 Triple 3-Input AND | (5P) | V-HOLD | |||
| PCHU-21-29 | 74LS14 Hex Schmitt Inverters | (4V) | — HCENT | [js | ||
| PCHU-21-30 | 74LS32 Quad 2-Input OR | (8C, 5T) | grigT | ston owe | ||
| PCHU-21-31 | 74LS42 4 To 10 Decoders | (4T) | ||||
| PCHU-21-32 | 74LS55 2-Wide 4-Input AND-OR-INVERT Gates (5K) | au ese | ||||
| PCHU-21-33 | 74LS74A Dual “D” Flip-Flops (P, CL) | (7J, 7K, 5M) | Os | |||
| PCHU-21-34 | _74LS109A Dual J-K Flip-Flops (PLE, CL) | (4Y) | ) | oa | ||
| PCHU-21-35 | 74LS139 Dual 2 To 4 Decoders | (7H, 2L, 6T) | Co | = | ||
| PCHU-21-36 | 74LS157 Quad 2 To 1 Data Selectors | (7S, 7T, 7U, 7V) | spmne Fuse | |||
| PCHU-21-37 | 74LS161A 4-Bit Binary Counters | (6H, 6, 6K, 6L, 6M, 4R) | oe: | ls Le] | ||
| PCHU-21-38 | 74LS164 8-Bit Shift Registers | (8H, 5Q) | ei}o | eS | ||
| PCHU-21-39 | 74LS165A 8-Bit Shift Registers | (8A, 8B) | poner | i | Os | |
| PCHU-21-40 | 74LS175 Quad “D” Flip-Flops (CL) | (48) | song ot | |||
| PCHU-21-41 | _74LS194A 4-Bit Shift Registers | (6Q, 6R) | (| | os | oT | |
| PCHU-21-42 | 74LS240 Octal Bus Inverters (TS) | (7A, 7B, 7C) | Le | |||
| PCHU-21-43 | 74LS244 Octal Buffers & Line Drivers (TS) | “ | 01 | |||
| (IL, 2M, 3M, 88, 5V, 6V) | 1 | ro | SY | |||
| PCHU-21-44 | _74LS245 Octal Bus Transceivers (TS) | (1K, 6Z) | — | “ | 3 | |
| PCHU-21-45 | 74LS259 8-Bit Addressable Latches | (7D, 7E) | |__ 70: | "Baan | | es | |
| PCHU-21-46 | —74LS299 8-Bit Shift/Storage Registers | (7L, 7N, 7Q) | : | _e | = | a |
| PCHU-21-47 | = 74LS367A Hex Bus Drivers | (4L) | osu sa ust | vote | ae en | ™ |
| PCHU-21-48 | 74LS368A Hex Bus Drivers | (8E, 8F, 5S) | ; | Fuse (Sow Bow) 3A, 128v—| | vi (~) (~) TL | ral | |
| PCHU-21-49 | 74HC373 Ocial “D” Transparent Latches C-MOS_ (3K) | a | ||||
| PCHU-21-50 | 74LS377 Octal “D” Flip-Flops | (6P) | Fuse (Slow Blow) 2.54, 125V | |||
| PCHU-21-51 | 74S04 Hex Inverters | (2G, 6N) | ||||
| PCHU-21-52 | 7437 Quad 2-Input NAND Buffers | (4X) | Fig. 6 | Video Monitor : [Y51 Type] XM-2001N | ||
| PCHU-21-53 | 75471 Dual Peripheral AND Drivers | (6C) | ||||
| PCHU-21-54 — 74HC10 Triple 3-Input NAND C-MOS | (8Y) | WARNING | ||||
| PCHU-21-55 | PST518A Low Voltage Detector | (72) | a | . | . | |
| PCHU-21-56 | _LM324 Quad Operational Amplifiers | (3E) | Do not touch the inside of the Video Monitor. | |||
| PCHU-21-57. | LM3900 Quad Operational Amplifiers | (1) | 't contains many parts supplied with high voltage. | |||
| PCHU-21-58 | CD 4066 Quad Analog Switches C-MOS | (3C, 2E) |
23 6
- Adjustment of Video Monitor
This game uses one of four types of Video Monitors which are different in appearance but identical in function. The four types can be interchanged.
- Video Monitor : [32 Type] 20-EZV(R-C)
- Video Monitor : [33 Type] 20-EZV(R-C)
- Video Monitor : [85 Type] 20-Z2AW
From To Game POB Greet Gain _ Video Montor 6P-600 Vileu Rod Gam JK. Man PCB Hamess . Bie can S Signal POB
INVERT OUT NON INVERT OUT
in case of PCH-UP, Plug in here!
H HOLD smotorsoniavs, OF
Ls
a Mam PCB
V-SIZE Fuse (Midget Type) 0.3A, 125V @} IC 401
DEGAUSS SWITCH ~«—
ee eeD This DEGAUSS SWITCH is H-CENT only attached to Video Monitor [33 Type] and [35 Type] SOUND VOLUME
Fig. 5 Video Monitor : [32 Type] 20-EZV(R-C) [33 Type] 20-EZV(R-C) [35 Type] 20-Z2AW
Do not touch the inside of the Video Monitor It contains Many parts supplied with high voltage. Continued
PART No. DESCRIPTION (Reference Designations and Locations) PCHU-21-59 2SA938 Silicon PNP Transistor (Q11, Q12, Q14, Q15, Q17, Q18)
| PCHU-21-60 | 2SA1015 Silicon PNP Transistor | (Q3, Q5, Q7, Q20) |
| PCHU-21-61 | 2SC1740 Silicon NPN Transistor | (Q8~Q10, Q13, Q16, Q19) |
| PCHU-21-62 | 2SC1815 Silicon NPN Transistor | (Q1, Q2, Q4, Q6) |
| PCHU-21-63 | ES1F Diode | (D1) |
| PCHU-21-64 | 1$5277B Diode | (D3, D4) |
| PCHU-21-65 | EGO1Y Diode | (D2) |
| PCHU-21-66 | DAN401 Quad Cathode-Common Diode Array | (DA1~DA6) |
PCHU-21-67 1.0f 5.5V Electric Double Layer Capacitor (EEC F5R5U105) (C3)
| PCHU-21-68 | 68pf 50V Ceramic-Disc Capacitor | (C44) |
| PCHU-21-69 | 100pf 50V Ceramic-Disc Capacitor | (C35, C36, C45) |
| PCHU-21-70 | 180pf 50V Ceramic-Disc Capacitor | (C11, C39) |
| PCHU-21-71 | 330pf 50V Ceramic-Disc Capacitor | (C2, C6, C12, C40, C41) |
| PCHU-21-72 | 1000pf 50V Ceramic-Disc Capacitor | (C5) |
PCHU-21-73 0.01uf 50V Ceramic-Disc Capacitor (C4, C22, C38, C43, C80~C179)
| PCHU-21-74 | 0.047uf 50V Ceramic-Disc Capacitor | (C15~C17) |
| PCHU-21-75 | 0.2uf 12V Ceramic-Disc Capacitor | (C21) |
| PCHU-21-76 | 0.047uf 50V Film Capacitor | (C33, C34) |
| PCHU-21-77 | tuf 16V Al Electrolytic Radial Cap. | (C7, C8) |
PCHU-21-78 3.3uf 16V Al Electrolytic Radial Cap. (C13, C14, C25, C28, C31, C32) PCHU-21-79 = 10uf 16V Al Electrolytic Radial Cap. (C23, C24, C26, C27, C29, C30, C37, C42)
| PCHU-21-80 | 33uf 16V Al Electrolytic Axial Cap. | (C9, C10) |
| PCHU-21-81 | 47 16V Al Electrolytic Radial Cap. | (C47 ~CS§0) |
| PCHU-21-82 | 100uf 16V Al Electrolytic Axial Cap. | (C18, C46) |
| PCHU-21-83 | 100uf 25V Al Electrolytic Axial Cap. | (C19) |
| PCHU-21-84 | 220uf 16V A! Electrolytic Axial Cap. | (C1) |
| PCHU-21-85 | 470uf 16V Al Electrolytic Axial Cap. | (C20) |
PCHU-21-86 3.3uf 16V Tantalum Electrolytic Cap. (C85, C90, C93, C102, C109, C121, C127, C145;C157)
| PCHU-21-87 | 0 Ohm Shunt Lead | (R99) |
| PCHU-21-88 | 10 Ohm 1/4W+5% Resistor | (R7) |
| PCHU-21-89 | 33 Ohm 1/4W+5% Resistor | (R32, R37, R47, R57, R67) |
| PCHU-21-90 | 51 Ohm 1/4W+5% Resistor | (R8, R19, R23, R27, R31) |
PCHU-21-91 100 Ohm 1/4W+5% Resistor (R17, R20, R24, R28, R68, R69, R73)
| PCHU-21-92 | 110 Ohm 1/4W+5% Resistor | (R23) |
PCHU-21-93 330 Ohm 1/4W+5% Resistor (R13, R14, R18, R21, R22, R25, R26, R29, R30, R36, RYO, R91, R97, R98)
| PCHU-21-94 | 510 Ohm 1/4W2+5% Resistor | (R46, R56, R66) |
| PCHU-21-95 | 820 Ohm 1/4W+5% Resistor | (R1, R2) |
| PCHU-21-96 | 1K Ohm 1/4W+5% Resistor | (R94~R96, R120 ~R131) |
| PCHU-21-97 | 2K Ohm 1/4W+5% Resistor | (R15) |
PCHU-21-98 2.2K Ohm 1/4W+5% Resistor
PCHU-21-99 (R35, R40, R42, R45, R50, R52, R55, R6O, R62, R65) 4.7K Ohm 1/4W+5% Resistor (R43, R53, R63)
PART No. DESCRIPTION (Reference Designations and Locations) PCHU-21-100 5.1K Ohm 1/4W+5% Resistor (R4, R5, R88, R89)
| PCHU-21-101 | 7.5K Ohm 1/4W+5% Resistor | (R16) |
PCHU-21-102 10K Ohm 1/4W+5% Resistor (R12, R34, R38, R41, R44, R51, R54, R61, R64, R74, R82, R83, R87, R92, R93)
| PCHU-21-103 | 12K Ohm 1/4W+5% Resistor | (R71) |
PCHU-21-104 20K Ohm 1/4W+5% Resistor (R6, R39, R70, R72)
| PCHU-21-105 | 100K Ohm 1/4W+5% Resistor | (R33, R75) |
| PCHU-21-106 | 200K Ohm 1/4W+5% Resistor | (R9~R11) |
| PCHU-21-107 | 360K Ohm 1/4W+5% Resistor | (R79) |
| PCHU-21-108 | 750K Ohm 1/4W+5% Resistor | (R78, R80,R84) |
| PCHU-21-109 | 1M Ohm 1/4W+5% Resistor | (R76, R85) |
| PCHU-21-110 | 1.8M Ohm 1/4W+5% Resistor | (R81) |
| PCHU-21-111 | 2.2M Ohm 1/4W+5% Resistor | (R77, R86) |
| PCHU-21-112 | Hex 5.1K Ohm Series Resistor Array | (RM1, RM16) |
PCHU-21-113 | Octal 1K Ohm Series Resistor Array (RM5, RM8~RM10, RM13) PCHU-21-114. Quad 68 Ohm Parallel Resistor Array (RM6, RM7, RM11, RM12, RM14, RM15) PCHU-21-115 | NT-01 Resistor Array (RM2~RM4)
| PCHU-21-116 | 500 Ohm Variable Resistor. Red Cap | (VR1) |
| PCHU-21-117 | 500 Ohm Variable Resistor. Green Cap | (VR2) |
| PCHU-21-118 | 500 Ohm Variable Resistor. Blue Cap | (VR3) |
| PCHU-21-119 | 8 MHz Crystal | (XA) |
| PCHU-21-120 | 20.160MHz Crystal | (X2) |
| PCHU-21-121 | 21.47727 MHz Crystal | (X3) |
PCHU-21-122 DC-DC Converter (Input 5V-Output 12V : MD12P070/150)
| PCHU-21-123 | 8-Station, Single-Throw, DIP Bit Switch | (SW1, SW2) |
| PCHU-21-124 | MINI-BIT Header | (SW3) |
| PCHU-21-125 | 16 Pin DIP IC Socket | (S6~S8) |
| PCHU-21-126 | 28 Pin DIP IC Socket | (S2~S5) |
| PCHU-21-127 | 40 Pin DIP IC Socket | (S1, S9, S10) |
| PCHU-21-128 | 20 Pin Flat Cable Header | (P1) |
| PCHU-21-129 | 96 Pin DIN Connector Receptacle | (CH.1~CH.10) |
| PCHU-21-130 | GL-3HD1 Visible Light Emitting Diode | (LED1) |
E. PCH1-ROM PCB Assembly : Order By Game Name
F. O54-FCC PCB Assembly : PARTS LIST
PART No. DESCRIPTION (Reference Designations) CHPU-23-01 054-FCC Complete PCB Assembly CHPU-23-11 252-28-50-168 56P Edge Connector
| CHPU-23-12 | 330 pf 50V Ceramic-Disc Capacitor | (C1~C30) |
| CHPU-23-13 | Ferrite Beads BL O2RN2-R62 | (FC1~FC30) |
- Power On/Off Switch A Power On/Off Switch is located in the rear of the game at the bottom center of the cabinet. See Fig. 1.
lf the results of the preceding steps are satisfactory, you are ready to plug the game in, and set the Power On/Off Switch to the “On” position.
This game MUST be grounded. Failure to do so may result in destruction of electronic components.
- Grounding of Game (Use only if 3 wire outlet is unavailable.) See Fig. 4
- A grounding wire should be connected to a grounding bar or a metal pipe which is firmly inserted into the ground.
- Do not connect the grounding to a water pipe, because polyvinyl-chloride pipes are sometimes used in water lines, and the electronic continuity to the ground may be interruppted.
- Absolutely do not conneci the grounding wire to a gas pipe, as this can be extremely dangerous.
Fig. 4 Grounding of Game
G. O79-FCC PCB Assembly : PARTS LIST
- Voltage Selection
| Before plugging in your game, make sure the Terminal Block of | PART No. | DESCRIPTION (Reference Designations) | |
| the Power Transformer is correct for your location’s line voltage. | PCHU-23-01 | 079-FCC Complete PCB Assembly | |
| PCHU-21-128 | 20 Pin Flat Cable Header | (P1, P2) | |
| CHPU-23-12 | 330 pf 50V Ceramic-Disc Capacitor | (C1~C19) | |
| Outlet through | CHPU-23-13 | Ferrite Beads BL O2RN2-R62 | (FB1~FB19) |
| utlet_ | thro | So |
A 63 +—— |solation
| Power Supply Assembly | q | Transformer (For Upper Monitor Only) | ||||
| 4 | ZB | AC 100V | Terminal Block | H.PP-1O00A Power Supply Assembly : PARTS LIST | Continued | |
| f | LE; | 100VA | US. | ~ | jer | : |
| LE, | MAX. | Europe Sen aee @ | PART No. | DESCRIPTION (Reterence Designations) |
Z QB — =
| % DA | CHPU-88-01 | PP-1000A Complete Power Supply Assembly | ||
| Loy | Serial Fuse | tO) | CHPU-88-02 | 3D-0163 Complete Power Supply PCB Assembly |
| CHPU-88-11 | 3D-3000 Hybrid IC | (IC1) | ||
| CHPU-88-12 | uPC78M24 3-Terminal Regulator | (IC2) | ||
| Main Fuse | CHPU-88-13 | TL431CLP Adjustable Shunt Regulator | (IC3) | |
| Oraoe ey | CHPU-88-14 | TLP541G Photo Coupler | (PC1) | |
| Europe 3A anoy | CHPU-88-15 | PC614 Photo Coupler | (PC2) | |
| (200 ~ 240V) | CHPU-88-16 | RB404/S4VB40 Diode | (D1) | |
| CHPU-88-17 | C25P04Q/20CS04M Diode | (D12) | ||
| CHPU-88-18 | 30DF2 Diode | (D11) |
CHPU-88-19 1S1835/10DF6 Diode (D6, D7, D10, D14)
| Power Transfomer PT-1021A | CHPU-88-20 | 18954 Diode | (D3) |
| baat through | CHPU-88-21 | RDS5. 1EB3 Zener Diode | (ZD1) |
| Fane ner | CHPU-88-22 | 5P2M Thyristor | (Q1) |
| AC 100V | CHPU-88-23 | 2S8C2562 Silicon NPN Transistor | (Q2) |
| 120VA | CHPU-88-24 | 2SC2749 Silicon NPN Transistor | (Q3) |
MAX.
| (Eat Loner Monitor and | Power Transom er oon | CHPU-88-25 | 0.01 uf S0V Mylar Capacitor | (C6, C9, C27) |
| Fluorescent Lamp | CHPU-88-26 | 0.1 uf 50V Mylar Capacitor | (C13) | |
| CHPU-88-27 | 1000 pf 50V Mylar Capacitor | (C12) | ||
| Power On/Off Switch | CHPU-88-28 | 0.047 uf 630V Metallezed Film Cap. | (C1, C4) |
CHPU-88-29 0.22 uf 250V Metallezed Film Cap. (C10, C28, C29) CHPU-88-30 2200 pf 2KV Ceramic-Disc Capacitor (C2,C3,C11,C15,C18)
| CHPU-88-31 | 4.7 uf 50V Al Electrolytic Cap. | (C7) |
| CHPU-88-32 | 47 uf 35V Al Electrolytic Cap. | (C8, C17) |
| CHPU-88-33 | 330 uf 200V Al Electrolytic Cap. | (C5) |
| CHPU-88-34 | 1000 uf 50V Al Electrolytic Cap. | (C16) |
| CHPU-88-35 | 3300 uf 10V Al Electrolytic Cap. | (C19~C26) |
| This game uses one of two types of transformers | CHPU-88-36 | 100 Ohm 1/4W +5% Carbon Resistor (R9,R11,R12,R23,R24 |
)
| which are different in appearance but identical in function. | CHPU-88-37) | 1K = Ohm 1/4W +5% Carbon Resistor | (R4, R6, R15) | |
| The two types can be interchanged. | CHPU-88-38 | 1.5K Ohm 1/4W +5% Carbon Resistor | (R25) | |
| CHPU-88-39 | 2.4K Ohm 1/4W +5% Carbon Resistor | (R26) | ||
| CHPU-88-40 | 10K Ohm 1/4W +5% Carbon Resistor | (R7) | ||
| . | nd Voltage Selection | CHPU-88-41 | 24K Ohm 1/4W +5% Carbon Resistor | (R17) |
| Fig. 3 Power Supply Assembly, Power Transformer and | Voltag: | CHPU-88-42 | 30K Ohm 1/4W +5% Carbon Resistor | (RB) |
| CHPU-88-43 | 5.1 | Ohm 1/2W +5% Carbon Resistor | (R19, R21) |
3 26
No. DESCRIPTION (Reference Designations)
| CHPU-88-44 | 100 Ohm 1/2W +5% Carbon Resistor | (R5) |
CHPU-88-45 100K Ohm 1/2W +5% Carbon Resistor (R3, R14)
| CHPU-88-46 | 5.1 | Ohm 5W +5% Cement Resistor | (R1) |
| CHPU-88-47 | 20 | Ohm 5W +5% Cement Resistor | (R22) |
| CHPU-88-48 | 30 | Ohm 5W +5% Cement Resistor | (R10) |
| CHPU-88-49 | 100 Ohm 5W +5% Cement Resistor | (R16) | |
| CHPU-88-50 | 510 Ohm 5W +5% Cement Resistor | (R20) | |
| CHPU-88-51 | 2K | Ohm Veritical Cermet Trimpot | (VR2) |
| CHPU-88-52 | 50K Ohm Vertical Cermet Trimpot | (VR1) |
CHPU-88-53 _ El-40 Type 3D-0163 Switching Transformer (TR) CHPU-88-54 SC2A Choke Coil (L1) CHPU-88-55 SF-C27-00105-01 Choke Coil (L2) CHPU-88-56 3A FGMB NR Type Fuse CHPU-88-57 OG751-0062 Fuse Holder (2 per assembly) CHPU-88-58 Heat Sink Clip (3 per assembly) CHPU-88-53 Thermally Conductive Rubber CHPU-88-60 2-Pin AC Input Connector Receptacle on PCB CHPU-88-61 6-Pin DC Output Connector Receptacle on PCB CHPU-88-62 7-Pin DC Output Connector Receptacle on PCB CHPU-88-65 3D-0163-32 Type Heat Sink
CHPU-88-63 3D-0163-30 Type Metal Frame CHPU-88-64 3D-0163-31 Type Metal Cover CHPU-88-66 3-Pin AC Input Connector Ass’y.on Metal Frame CHPU-88-67 9-Pin DC Output Connector Ass’y.on Metal Frame CHPU-88-68 12-Pin DC Output Connector Ass’y. on Metal Frame CHPU-88-69 Metal PCB Retainer (4 per assembly)
|. PCH1-UP Fuses
PART No. DESCRIPTION(Reference Designations) TKGU-11-08 Main Fuse U.S. 5A 125V CHVU-63-11 Main Fuse Europe 3A 250V
CHPU-88-56 Power Supply Fuse 3A 125V(Midget)
TKGU-11-12 Video Monitor Fuse 20-EZV(R-C), 20-Z2AW 4A 125V(Slow Blow) (F302)
TKGU-11-13 Video Monitor Fuse 20-EZV(R-C), 20-Z2AW 0.3A 125V(Midget) (F301)
MDST-63-12 Video Monitor Fuse XM-2001N 2.5A 125V(Slow Blow) (F702)
MDST-63-13 Video Monitor Fuse XM-2001N 3A 125V(Slow Blow) (F701)
Check before plugging the game in!
The game“PlayChoice-10™” is shipped ready for operation, but a last visual check should be made to insure the final touch of quality control. Please check the following to help us insure that your new game was delivered to you in good condition.
- Check the exterior of the game for shipping damage, dents, chips, or broken parts.
- Remove the screws on the Rear Door Panel.
- Unlock and open the Rear Door Panel, as well as the Service Door inspect the interior of the game as follows:
- Check that Plug-in connectors are firmly connected.
- Check that Plug-in integrated circuits on the Game PCB are firmly connected in their sockets.
- Check that all major subassemblies such as the Power Supply, Operation Panel, and Video Monitor are properly mounted.
- Remove the tie-wrap that holds the coiled Power Cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation.
B. Game Installation
Fig. 2 Installation Requirements
Power : 170 watts Temperature : Oto 38deg.C (32 to 100 deg F) Humidity : Not over 95% relative Space required: 63(W) x 90 (D)cm (24 3/4 x 35 1/2 in.) Height > 189¢cm (74 1/2 in.)
SWIVEL CONTACT ASSY AMP EI3P IR3T07 ea tis
MICRO SW SS-SGL
062G2 GUN P.C.B. ASSY
PARTS NAME LSuni[s-aer-ael 7 [ng ; | 106 2G2 iy
DRAWIN NO a a oe eee! VINTENDO 412
MEMO
A. Game Inspection
PCH Display Panel Game Serial Number Label (Name Plate)
CHP-US Front Screen
PCH
Video Monitor
Video Monitor
Game PCB 079 Shield Cover
Power Supply Assembly
Main Fuse Power On/Off Switch 054 Shield Cage
Power Cord
Power Transformer
Fig. | Game Overview
MEMO
cc 1 Contents [
- Location Setup 1
| A. | Game Inspection -- | 4 |
| B. | Game Installation-- | 2 |
- Voltage Selection--- 3
- Power On/Off Switch-- 4
- Grounding of Game --- 4
- Adjustment of Video Monitor -+-..:--::sssseeeereeeeeeeee eee 5
- Option Switch Settings 7
| A. | Game Settings | 8 |
- Self-Test and Bookkeeping -------.::--- ieee erect eee 9
- Maintenance and Repair --- A. Fuse Replacement **" B. Cleaning Cc. Operation Panel -- D. Video Monitor Removal E. Game PCB Removal and ROM PBC Exchange-:-:-:++--- 14
- Radio Frequency Interference cece eeeeeeceeeeaeeeeee 14
- Wiring and Connection vvrricitertiees 15
- Parts Lists -cccccccctrccccrett eset ct eter te ee eeete ees + 17 PCH1-UP Game Cabinet Assembly .. PCH1-UP Operation Panel Assembly PCH1-UP Wiring Harnesses - PCH1-CPU PCB Assembly :-- PCH1-ROM PCB Assembly -- 054-FCC PCB Assembly -- 079-FCC PCB Assembly -- PP-1000A Power Supply Assembly -- PCH1-UP Fuses -LOMNMGVODD
_ PlayChotce-10