CATHODE RAY TOMES

Major Havoc TM-267 1st Printing Conversion for Tempest

Major Havoc (rev 3) (Atari, 1983) · Technical Manual · 58 pages · 35 sections · original scan

Page 1

Conversion Instructions

for Tempest”

ae Q Atiarne: Communcatons Company

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 4

© 1984 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form ofa phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher, The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976, This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. Inaddition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari, Inc. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed in the U.S.A. 4N

Be pe Be

Page 5

TABLE OF CONTENTS

Introduction. . 2... 2 eee eee Kit Parts Inventory. ......-.

Assembly Removal Instructions . A. B. Cc. De E.

Assembly Modification Instructions F. G. He I. J. RK. L. Remove the Attraction Panel Remove the Control Panel. . Remove the Display. .... Remove the Printed-Circuit Boards Remove the Power Supply... .

Modify the Slam Switch. ... Modify the Power Supply... Modify the Display. ..... Modify the Control Panel. . . Modify the Attraction Panel . Modify the Display-Mounting Frame Modify the Rear Access Panel. .

Assembly Installation Instructions. .... M N. oO. Pe Q. R s. T. Ue Vv. Ww. x. Y. Install the Side-Panel Decals (optional) Install the Attraction Panel. ..... Install the Display .......-.- Install the Control Panel. ...... Install the Major Havoc Printed-Circuit Install the Power Supply. ... Install the Fan. ....... Install the Self-Test Chart . . Install the Labels. ...... Inspect the Major Havoc Game. . Adjust the Display. ...... Set the Option Switches .... Update the Game Documentation .

iv Pe ee oY

Page 6

Figure Figure Figure Figure

Figure Figure Figure Figure

Figure Figure Figure Figure

Figure Figure Figure Figure Figure

Table 1 Table 2 Table 3 BWNE

Ory MAH LIST OF ILLUSTRATIONS

Removing and Installing the Attraction Panel. .... Removing, Modifying, and Installing the Control Panel. Removing the Display .......- Removing the Printed-Circuit Boards.

Modifying the Slam Switch. ..... Modifying the Power Supply ..... 1N754A and 1N756A Zener Diode Connections. . Modifying the Deflection PCB. ...

Modifying the Display-Mounting Frame... . 1... Modifying the Rear Access Panel, Installing the Fan. Installing the Display... 1... eee en eee Installing the Major Havoc Printed-Circuit Boards. .

Installing the Labels. ....... Adjusting the Display. ....... Input Protection Circuit Schematic . Deflection PCB Schematic (Versions 1, 2, and 3). Deflection PCB Schematic (Version 4)

LIST OF TABLES

Rit Parts... ee ee et ee Display Versions. . 2... ee eee eee ee

Page 7

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A WARNING A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire oudet. Ifyou have only a 2-wire outlet, we recommend you hire a Jicensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game’s power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands of with metal objects! Always discharge the high voltage from the CRT before servicing this area Of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap, Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care, If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion, Use the Proper Fuses, To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, volt age rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors oneach printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

vi

Page 8

INTRODUCTION

This document includes the instructions necessary for changing your upright Tempest® game into a Major Havoc™ game. The instructions include: (1) modifying the power supply, display, control panel, attraction panel, display-mounting frame, rear access panel, and slam switch; and (2) installing a fan, decals, and Major Havoc game printed-circuit boards (PCBs). The procedures are organized to accamplish the change in the most efficient’ manner.

A Major Havoc instruction manual and schematic package is included with the kit. Keep your Tempest instruction manual and schematic package for information pertaining to those parts of the Tempest game that are not modified by this Major Havoc conversion.

NOTE

Do not discard this document after the conversion is campleted. Keep this document as a supplement to the Major Havoc operators manual and display manual.

KIT PARTS INVENTORY

The parts listed in Table 1 are included or are available as options to the Major Havoc Conversion Kit.

Table 1 Kit Parts A042443-01

Part No.QuantityDescription
A034629-011AC Harness
A038088-01Opt ionalInput Protection Circuit PCB Assembly
A040547-031Fan and Bracket Assembly
A041347-211Major Havoc PCB Assembly
A042392-011Major Havoc Conversion PCB Assembly

A042445-01 X-Y Display Kit--includes

31-1N40024Type-1N4002 Diode
32-1N756A28.2 V, Type-1N756A, Zener Diode
110000-303130 k2, 5%, 1/4 W, Resistor
131002-00126.8 V, Type-1N754A, Zener Diode
A042448-011Fan Harness Assembly
Page 9

Major Havoc Installation Instruct ions TM-267

Table 1 Kit Parts, continued A042443-01

Part No.Quant ityDescription
72-1124S4#10-24 x 1-1/2-Inch Cross-Recessed,

4 Pan-Head Machine Screw

75-040S4#10 Split-Lock Washer
75-9910N025/8-Inch Stamped Nut
75-995114#10-24 Nut/Washer Assembly
78-240124Beaded Nylon Tie
72-HA4804S,1#8-32 x 1/4-Inch,-Cross-Recessed,

Pan-Head Screw

042447-011Control-Panel Decal
034536-0211/2-Inch Foam Pad
034536-0311-1/8-Inch Foam Pad
037713-011Attraction-Panel Glass
042413-011Label Kit~—includes
038158-01iConversion Kit Label (Non-UL)
039450-011FCC Compliance Label
042421-01Opt ionalLeft Side-Panel Decal
042421-02Opt ionalRight Side-Panel Decal
042307-011Display-Rotate Template
042444-011Bezel
042446-011Attraction-Panel Decal
042449-011Fan Mounting Block
042450-011PCB Mounting Bracket
160013-0012Leaf Switch with Button Holder
175007-0018#10 Flat Fender Washer
176015-1101#10 x 5/8-Inch Cross-Recessed, Deep-

Thread Pan-Head Screw

176020-2202#8 x 1-1/4-Inch Cross-Recessed, LP

Washer-Head Screw

177003-0404#10-24 ToNut
178030-0041Pushbutton Assembly (Red)
178030-0071Pushbutton Assembly (Yellow)
178065-1002Tie Wrap
CO-252-041Supplement to TM-267
SP-2521Major Havoc Schematic Package
ST-252-011Major Havoc Label with Self-Test

Procedure and Option Switch Settings

™-2521Major Havoc Operators Manual
TM2671Major Havoc Conversion Instructions

for Tempest

Page 10

Major Havoc Installation Instruct ions TM-267

TOOLS REQUIRED

The tools listed in Table 2 are required to perform a complete conversion.

Table 2 Tools Required

Description Purpose

#2 Phillips Screwdriver

5/64-Inch Allen Wrench

1/8-Inch Allen Wrench

1/4-Inch Hex Driver

3/8-Inch Hex Driver

11/32-Inch Hex Driver

7/16-Inch Hex Driver

5/8-Inch Open-End Wrench

Sabre Saw

15-27 W Soldering Iron

Electric Hand Drill

1/4~Inch Drill Bit

#11 X-ACTO Knife (optional)

Heat Gun or Hair Drier Removing the attraction panel and power supply

Modifying the power supply

Installing the attraction panel, display, power supply, and fan

Modifying the control panel

Removing the display

Removing the display

Modifying the control panel

Removing the power supply

Modifying the power supply

Removing the control panel and display

Installing the control panel

Modifying the control panel

Modifying the display~mount ing frame and rear access panel

Modifying the display

Modifying the display-mount ing frame and rear access panel

Modifying the display-mount ing frame and rear access panel

Installing the side panel decals

Removing the cont rol-panel decal

Page 11

Major Havoc Installation Instructions TM-267

ASSEMBLY REMOVAL INSTRUCTIONS

WARNING

To avoid electrical shock, unplug the game before performing the conversion procedures.

NOTE

These procedures must be performed by qualified service personnel. All interior and exterior surfaces of the cabinet and the working area should be clean and free of foreign material before starting the procedures,

The following procedures are arranged in the sequence recommended for performing the game conversion. The parts of your game that are affected by the conversion are removed, modified, and the new Major Havoc parts are installed.

A, REMOVE THE ATTRACTION PANEL

Perform the following procedure to remove the attraction panel fran the game cabinet (see Figure 1).

Ky From the rear of the cabinet, use a Phillips screwdriver to remove the four wood screws securing the fluorescent light and speaker assembly to the cabinet.

Slide the fluorescent light and speaker assembly partially out the back of the cabinet.

Disconnect the fluorescent light and speaker assembly harness connector .

Remove the fluorescent light and speaker assembly fram the cabinet.

ae Fron inside the housing area for the fluorescent light and speaker

el assembly, use a Phillips screwdriver to remove the four wood screws securing the attraction panel to the cabinet.

Remove the attraction panel.

Page 12

Major Havoc Installation Instruct ions ™-267

Attraction Panel Wood Screws

\ Fluorescent Light and Speaker Assy

Figure 1 Removing and Installing the Attraction Panel

Page 13

Major Havoc Installation Instruct ions ‘IM-267

Perform the following procedure to remove the control panel fram the game cabinet (see Figure 2). ae Unlock and open the coin door.

  • Reach up through the coin-door opening and release the spring-draw latches on each end of the control panel.
  • Disconnect the control-panel harness connector fram the game harness. w/ Use a 7/16-inch hex wrench to remove the three nuts and washers securing the control panel to the cabinet (save the mounting hardware for reuse).
Page 14

Major Havoc Installation Instruct ions TM-267

Leaf Switches Encoder-Wheel Controt Leaf-Switch Pushbutton

Encoder Knob Coupler PCB Connector

Ya-Inch Adhesive Strip

Switch Cone Bezel

e-inch Hex Nut

Control-Panel Harness Connector

Player Start Pushbutton Switches

Players may receive an electrical shock if the contro! panels not properly grounded. After modifying the control panel, make certain the green ground wireis firmly attached to the metal latch tab. Black Black “mon TF (4) Red ary cH (+) Red = White L Brown

1-Piayer Start 2-Player Start

Figure 2 Removing, Modifying, and Installing the Control Panel

Page 15

Major Havoc Installation Instruct ions TM-267

~ @. REMOVE THE DISPLAY

Perform the following procedure to remove the display fram the game cabinet (see Figure 3).

2.

3.

WARNING

Shock Hazard

High voltages may exist in the display circuitry, even with power disconnected. Use extreme caution. Do not touch the display circuitry with your hands or with metal tools.

Implosion Hazard

Use extreme caution when handling the display. If you drop the display and the cathode-ray tube breaks, it may implode! Shattered glass can fly six feet or more fran the implosion. To avoid injury, we recommend that two people, wearing gloves and safety glasses, perform the following removal procedures.

Use a 1/8-inch Allen wrench to remove the three screws securing the retainer to the top of the display shield.

Remove the retainer and grille fran the top of the display shield.

Carefully remove the tempered-glass display shield by firmly grasping the bottom of the shield and lifting up.

Remove the staples securing the cardboard display bezel to the cabinet and remove the bezel.

Remove the rear access panel fran the cabinet.

Discharge the high voltage fram the cathode-ray tube (CRT) before proceeding:

a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground.

b. Mamentarily touch the free end of the grounded jumper to the CRT anode by carefully sliding the jumper under the anode cap.

c. Wait two minutes and repeat step 6b.

Page 16

Major Havoc Installation Instructions TM-267

7.

10. Fram the back of the cabinet, disconnect the 15-pin Molex connector from the display.

Use a 7/16-inch hex driver to remove the display support bracket fram the display chassis.

Fram the front of the cabinet, use a 3/8-inch hex driver to remove the four nuts and flat washers securing the display to the displaymounting frame. Do not remove the upper two bolts fran the displaymounting frame.

Carefully pull the display chassis out through the front of the cabinet.

Page 17

Major Havoc Installation Instructions TM-267

Display-Mounting Frame

Grille

Display Shield

Disptay-Support Bracket

Figure 3 Removing the Display |

Page 18

od Major Havoc Installation Instructions T™-267

f \.& REMOVE THE PRINTED-CIRCUIT BOARDS

Perform the following procedure to remove the Tempest game PCBs from the game cabinet (see Figure 4).

we

a a

wy Disconnect the game harness edge connectors from the two game PCBs. If the edge connectors are secured with screws or tie wraps, remove the screws or tie wraps before disconnecting the edge connectors fran the PCBs.

Use a Phillips screwdriver to remove the screw, washer, and two Spacers securing the top right corner of the PCBs to the cabinet wall.

Carefully slide the PCBs straight out of their slots.

\\EX_REMOVE THE POWER SUPPLY

Perform the following procedure to remove the power supply fran the game cabinet.

Le

re /

/

sf

Sf es Disconnect the four harness connectors (Jl, J2, J4A, and J5).

Disconnect the power cord from the power supply.

Use a 11/32-inch hex driver to remove the nut and star washer fran the ground screw attaching the green grounding wires to the power supply.

Cut the cable tie located on the rear right corner of the power supply chassis.

Use a Phillips screwdriver to remove the four screws securing the power supply to the cabinet.

Remove the power supply fram the cabinet. Be careful not to damage the Regulator/Audio II PCB located above the power supply.

-ll-

Page 19

Major Havoc Installation Instructions

Tempest Game PCBs

Regulator/ Audio II PCB

Figure 4 Removing the Printed-Circuit Boards v TM-267

a

Page 20

Major Havoc Installation Instructions T™M-267

ASSEMBLY MODIFICATION INSTRUCTIONS

The following procedures describe the modifications required for this conversion. Provide a clean work surface on which to perform the modifications to the assemblies removed fran the game cabinet.

worry THE SLAM SWITCH

In the Tempest game, the slam switch is used to cancel credits if the game is being jarred or tipped. In the Major Havoc game, the slam switch is used as a diagnostic step selector and auxiliary coin switch. Consequently, the slam switch must be modified to prevent free credits from being obtained if the game is jarred or tipped.

Perform the following procedure to modify the slam switch (see Figure 5). ae Open the coin door,

d Locate the slam switch in the upper left corner of the coin door. 3h US-Made Coin Door. Gently bend the stationary leaf contact out approximately 1/2-inch so that the switch will not close when the game cabinet is tipped or jarred.

British-Made Coin Door. Cut the weighted end off the microswitch pendulum so that the switch will not close when the game cabinet is tipped or jarred.

Page 21

Major Havoc Installation Instructions TM-267

Cut Here

Weighted Pendulum

British-Made Coin Door

Stationary Leaf Bend Approximately Ye-Inch

US-Made Coin Door

Figure 5 Modifying the Slam switch”

Page 22

Major Havoc Installation Instructions TM-267

hs MODIFY THE POWER SUPPLY

Perform the following procedure to modify the power supply to provide a parallel 110-volt AC circuit to power the fan (see Figure 6). iv Set the power supply upside down on a clean work surface.

2 Install the three-pin AC harness connector with the white wire on

ae

a 4,

‘se the left end of the connector.

Connect the white wire fran AC harness connector J4B to the terminal lug adjacent to the white wire fran connector J4A.

Connect the black wire fran AC harness connector J4B to the terminal lug adjacent to the black wire fran connector J4A.

Use a 11/32-inch hex driver to remove the nut and star washer fron the ground screw securing the green wires and the line filter to the power supply. Remove the ground screw.

Attach the green wire fram connectors J4A and J4B and the green wire from connector J2 to the ground screw.

Insert the ground screw, with the green wires attached, through the line filter bracket and power-supply chassis.

Use a 11/32-inch hex driver and a Phillips screwdriver to secure the nut and star washer, removed in step 5, to the power supply.

Check that the power supply fuses match the ratings given on the labels located near the fuse block and the cartridge fuse holder.

Page 23

Figure 6 Modifying the Power Supply

Page 24

Major Havoc Installation Instruct ions TM-267

l. MODIFY THE DISPLAY

There are four versions of the Wells-Gardner display used in the Tempest game. Perform the preliminary procedure for all versions of the display, then refer to Table 3 to determine which version of the four displays was installed in your Tempest game and perform the additional procedure for that version.

CAUTION:

When soldering canponents to the display circuitry, apply just enough heat to provide a proper electrical connection. Excessive heat can damage the semiconductor material.

preliminary Procedure

Perform the following procedure to modify the Deflection PCB (see Figures 7 and 8).

dl. Set the display on a clean work surface.

2... Disconnect the 15-pin Molex connector fran the mounting bracket on “""" the display chassis and the harness connectors from the Deflection PCB and the Neck PCB.

‘3~° Use a 1/4-inch hex driver to remove the two screws securing the Deflection PCB to the display chassis, a/, Remove the Deflection PCB fram the display.

SA Connect two type-1N754A Zener diodes together, anode to anode, as shown in Figure 7. Use a soldering iron to solder the two anode leads together.

Solder Here

Figure 7 1N754A and 1N756A Zener Diode Connections

Page 25

Major Havoc Installation Instructions ™267

6 Connect two type-1N756A Zener diodes together and solder as described in step 5.

va Examine the soldered side of the Deflection PCB removed from the display and determine which of the two PCBs shown in Figure 8 Matches your PCB. ‘Py!-/.;

8: On the camponent side of the Deflection PCB, locate the yellow wire (top right side of the PCB).

‘9. Solder one cathode lead of the two type-IN754A Zener diodes (soldered together in step 5) to the yellow lead on the soldered side of the PCB as shown on the appropriate illustration in Figure 8.

10° Solder the other cathode lead of the two type-1N754A Zener diodes to ground as shown on the appropriate illustration in Figure 8. oon the component side of the Deflection PCB, locate the orange wire (near top center of the PCB).

\12. Solder one cathode lead of the two type-1N756A Zener diodes (soldered together in step 6) to the orange lead on the soldered side of the PCB as shown on the appropriate illustration in Figure 8.

13,° Solder the other cathode lead of the two type-1N756A Zener diodes to ground as shown on the appropriate illustration in Figure 8.

My On the component side of the Deflection PCB, locate connector P600 (right center of the PCB).

  • Solder the cathode lead of a type-1N4002 diode to pin 1 and the anode lead to pin 4 of connector P600 on the soldered side of the PCB as shown on the appropriate illustration in Figure 8.

16/ Solder the cathode lead of a type-1N4002 diode to pin 5 and the anode lead to pin 7 of connector P600 on the soldered side of the PCB as shown on the appropriate illustration in Figure 8. at On the component side of the Deflection PCB, locate connector P700 (left center of the PCB). as/ Solder the cathode lead of a type-1N4002 diode to pin 1 and the anode lead to pin 4 of connector P700 on the soldered side of the PCB as shown on the appropriate illustration in Figure 8.

Page 26

Major Havoc Installation Instruct ions

TM-267

& 1N756A Zener Diodes

a

1N756A Zener Diodes

1K®Q, % Wresistorinstalled in the procedure for Version 3 under “‘H. Modify the Display” is attached to this point. 1N754A Zener Diodes

1N4002 Diodes | 1N4002 Diodes

Figure 8 Modifying the Deflection PCB

Page 27

Major Havoc Installation Instruct ions TM-267

“19. Solder the cathode lead of a type-1N4002 diode to pin 5 and the anode lead to pin 7 of connector P700 on the soldered side of the PCB as shown on the appropriate illustration in Figure 8.

  • Refer to Table 3 to determine which of the four versions of the display has been installed in your Tempest game.

Table 3 Display Versions

Determine Procedure

Deflection PCB has two large, black, version 1 tubular capacitors, C804 and C805, (below top center of PCB) installed.

Input Protection Circuit PCB is Version 2 installed (piggyback) with a i_k2,+5%, 1/4 W resistor connected between the Input Protection Circuit PCB and the Deflection PCB.

“ Input Protection Circuit PCB is _ Version 3 installed (piggyback) but does not have a resistor between the Input Protection Circuit PCB and the Deflection PCB.

Deflection PCB does not have Version 4 capacitors C804 and C805 (below top center of PCB) or a Input Protection Circuit PCB installed.

  • Perform the procedure as follows for the appropriate version of the display determined fram Table 3. (Refer to the display manual, TM 183, for camponent and connector locations.)
Page 28

Major Havoc Installation Instructions 'T™M-267

NOTE

The 30 kx, 1/4 W resistor supplied in the kit is used only for Version 1 of the display.

Version 1

Perform the following procedure for Version 1 of the display.

i. Verify that the Preliminary Procedure has been performed.

  • Use a soldering iron to remove resistor R811 and replace it with the 30 k2, 1/4 W resistor supplied in the kit.
  • Use a 1/4-inch hex driver to secure the modified Deflection PCB to the display chassis.
CAUTION

Make certain that the harness from Q705 and Q706 is connected to P700 and not P1006.

  • Connect the harnesses to the appropriate Deflection PCB connectors.

Version 2

Perform the following procedure for Version 2 of the display.

  • verify that the Preliminary Procedure has been performed.
  • Use a 1/4-inch hex driver to secure the modified Deflection PCB to the display chassis.
CAUTION

Make certain that the harness from Q705 and Q706 is connected to P700 and not Pi00.

  • Connect the harnesses to the appropriate Deflection PCB connectors.
Page 29

Major Havoc Installation Instructions ‘TM-267

“ version 3

Perform the following procedure for Version 3 of the display. ya I. Verify that the Preliminary Procedure has been performed.

2s Locate the wire connected to resistor RL (22 kg) and the collectors of transistors Ql and Q3 (type 2N3904) on the Input Protection Circuit PCB and the point shown in Figure 8 on the Deflection PCB.

‘3<" Use a wire cutter to cut the wire, located in step 2, half-way between the two PCBs.

AS Use a soldering iron to solder a 1 kg, +5%, 1/4 W resistor (not included in the kit) between the two ends of the wire cut in step 3. Yo “Sx” ‘Use a 1/4-inch hex driver to secure the modified Deflection PCB to the display chassis.

UTION'

Make certain that the harness fran Q705 and Q706 is connected to P700 and not P100.

  • Connect the harnesses to the appropriate Deflection PCB connectors,

Version 4

Perform the following procedure for Version 4 of the display.

NOTE

This version of the display requires that an Input Protection Circuit PCB assembly be installed on the Deflection PCB as part of the display modification procedure. This PCB assembly is not included in the kit. Contact your nearest distributor for availability. Use the order form at the back of this document. Refer to Table 1 for the appropriate part number.

  • Verify that the Preliminary Procedure has been performed. oin tr
Page 30

Major Havoc Installation Instructions TM-267

  • Install the Input Protection Circuit PCB to the Deflection PCB as described in the instructions supplied with the Input Protection Circuit PCB assembly.
  • Use a 1/4-inch hex driver to secure the modified Deflection PCB to the display chassis.
CAUTION

¢ Make certain that the harness from Q705 and Q706 is connected to P700 and not P100.

4, Connect the harnesses to the appropriate Deflection PCB connectors.

J. MODIFY THE CONTROL PANEL =

CAUTION

a The following procedure should be performed 4 on a clean work surface to prevent con- ' taminating the exposed adhesive surface of the control panel.

Perform the following procedure to modify the control panel (see Figure 2). Qe Remove the two LED player-start pushbutton switches fram the control panel by holding the switch-cone bezel and rotating the switches counterclockwise.

2” Disconnect the harness wire fast-on lugs fran the player-start and pushbutton leaf switches. % Disconnect the connector from the encoder-wheel Coupler PCB.

  • Use a 5/8-inch open-end wrench to remove the stamped nuts securing the two pushbutton leaf switches to the control panel. t co ‘Use a 5/64-inch Allen wrench to remove the knob fram the encoderwheel control. oan
  • Use a 3/8-inch hex driver to remove the two nuts securing the ~“ encoder-wheel control to the control panel.

\L.—~ Directly heat the control-panel decal, not the metal, with a heat gun or hair drier. Do not melt the decal. (The decal can be removed without heating, but it is more difficult.)

los. Grasp the corners of the control-panel decal and, while applying heat, peel the decal off.

Page 31

Major Havoc Installation Instruct ions TM-267

NOTE

If you were able to remove the decal evenly without contaminating the adhesive surface and you are confident that you can properly position the Major Havoc decal on the control panel in one application, proceed to step 10.

y . Use a lint-free cloth wetted with isopropyl alcohol to remove the residual adhesive fran the control panel. Do not use paper towels. Repeat the cleaning operation (at least four applications) to make certain all the adhesive is removed.

eo. Cut and remove a strip of the protective backing fran the switch

holes near the center of the decal.

lL. tarefully position the Major Havoc control-panel decal so that the \" holes in the Major Havoc decal are aligned with the holes in the control panel. Then press the center of the decal onto the control panel.

12,” Remove the protective backing fran one end of the decal and use the

palm of your hand to rub the decal from the center toward the end of the control panel. Repeat for the opposite end of the decal. By Use a 3/8-inch hex driver to secure the encoder-wheel control to an control panel with the two nuts removed previously.

  • Use a 5/8-inch open-end wrench to secure the two new leaf switches and pushbuttons to the control panel. (The red pushbutton goes in the FIRE hole; the yellow pushbutton goes in the SHIELD hole.)

15 Connect the harness fast-on lugs and connector to the switches and encoder-wheel Coupler PCB.

  • Install a 24-inch strip of 1/4-inch adhesive-backed foam tape (not included in the kit) to the top edge of the control panel.
Page 32

Major Havoc Installation Instruct ions ‘TM-267

Je“ MODIFY THE ATTRACTION PANEL

Perform the following procedure to modify the attraction panel.

wy Qe Remove the staples securing the attraction panel to the frame.

Grasp each corner of the attraction-panel decal and peel the attraction-panel decal fram the frame. Keep the speaker grille and discard the Tempest decal and attraction-panel glass.

Lay the attraction-panel frame on a clean work surface.

Set the new attraction-panel glass and the speaker grille (with the original side up) into the appropriate recesses in the attract ionpanel frame.

Position the Major Havoc attraction-panel decal on the attractionpanel frame so that the grille slots in the decal are properly aligned with the grille. Use the impression of the original decal slots on the grille as a guide.

Use the palm of your hand to rub the decal onto the attract ionpanel glass, grille, and frame fram the center toward each end. se Acoury THE DISPLAY-MOUNTING FRAME Perform the following procedure to modify the display-mount ing frame (see Figure 9).

Qe

a”

ve,

e/ Fran the front of the cabinet, place the display-rotate template onto the top two display-mounting bolts in the display-mounting frame, Center the template on the display-mounting frame.

Use a dark marking pen to mark the display-mounting frame through the holes of the template. Then trace along the edges of the template.

Use an electric hand drill with a 1/4-inch bit to drill out the holes marked in step 2.

Use a sabre saw to cut the wood fram the display-mounting frame by following the lines marked from the template.

Page 33

Major Havoc Installation Instruct ions T™-267

Display-Mounting Bolts

Display-Rotate Template

Display-Mounting Frame

Figure 9 Modifying the Display-Mounting Frame

Page 34

Major Havoc Installation Instructions TM-267

\beWODIFY THE REAR ACCESS PANEL

Perform the following procedure to modify the rear access panel to provide a fan intake opening (see Figure 10). he Measure and mark the rear access panel for the fan intake opening as shown in Figure 10. be"'Use an electric hand drill with a 1/é-inch bit to drill holes in the rear access panel at each corner of the marked fan intake opening.

.3e" Use a sabre saw to cut the wood fran the fan intake opening.

Page 35

Major Havoc Installation Instruct ions T™-267

Cabinet Cleat

Intake Opening Location Mounting Block Marks

Fan and Bracket Assy

11.25

<a: ee 2 ZF. KA Fan Hamess

Rear Access Panel Green Ground Wire

Figure 10 Modifying the Rear Access Panel and Installing the Fan

Page 36

Major Havoc Installation Instructions 'T™M-267

ASSEMBLY INSTALLATION INSTRUCTIONS

The following procedures describe the installation of the Major Havoc assemblies.

M, INSTALL THE SIDE-PANEL DECALS (OPTIONAL)

NOTE

The Major Havoc side-panel decals are not included in the kit. However, if you wish to purchase these decals, use the order form provided at the back of this document. Refer to Table 1 for the appropriate part numbers.

Perform the following procedure to install the Major Havoc side-panel decals on the game cabinet.

1.

2.

5.

6.

7. Mix a normal solution of any liquid dishwashing detergent and approximately three quarts of water in a bucket.

Clean all oil film and dust from the sides of the cabinet and fill any dents or gouges with a filler material.

NOTE

We recammend that the following procedure be performed by two persons. One person may have difficulty handling the cabinet and the large decals.

Tip the game cabinet and gently lay one side on a blanket.

Use a sponge to liberally apply the water and detergent solution over the entire side of the cabinet.

Grasp the top edge of the appropriate decal for the side of the cabinet. Hold the decal up and off of the floor and peel away the protective backing.

Gently lay the decal, sticky side down, in the center of the wet surface of the cabinet. Position the decal to ensure that the graphics are centered on the side of the cabinet.

After the decal is in position, use the squeegee to remove all the excess water and detergent fran beneath the decal by quickly working from the center to the outside edges. HINT: If any air bubbles

Page 37

Major Havoc Installation Instructions 'TM-267

form, puncture them with a pin or the tip of an X-ACTO™ blade. Rub gently with a soft cloth to disperse the trapped air.

  • Carefully insert a #11 X-ACTO™ blade (or suitable substitute) between the T-molding and cabinet wall and, following the contour of the cabinet, cut off the excess decal. Rub the cut edges with a cloth to smooth down any rough edges.
  • When the wrinkles are removed and the decal is free of all excess water and detergent, gently turn the game cabinet over to the opposite side. Be careful to avoid damaging the freshly applied decal.
  • Repeat steps 2 through 8 for the remaining decal.

ll. Carefully raise the cabinet to the upright position.

  • Use a lint-free cloth to wipe off any excess water and detergent fram inside and outside of the cabinet. Allow time to dry before proceeding.

va \Ne INSTALL THE ATTRACTION PANEL

Perform the following procedure to install the Major Havoc attraction panel in the game cabinet (see Figure 1).

vA Fram the front of the cabinet, install the modified attraction Oe Fran the rear of the cabinet, use a Phillips screwdriver to secure

panel into the game.

the attraction panel to the cabinet with the four wood screws reoe previously. From the rear of the cabinet, slide the light and speaker board assembly part way into its housing area. Nad Connect the five-pin Molex connector to the light and speaker board harness.

wh Use a Phillips screwdriver to secure the light and speaker board

assembly to the cabinet with the four wood screws removed previously.

Page 38

Major Havoc Installation Instruct ions TM-267

y f \Q.INSTALL THE DISPLAY

WARNING

Use extreme caution when handling the display. If you drop the display and the cathode-ray tube breaks, it may implode! Shattered glass can fly six feet or more fran the implosion forces. To avoid injury, we recommend that two people, wearing gloves and safety glasses, perform the following installation procedure.

Perform the following procedure to install the modified display in the game cabinet (see Figure 11). la Remove all wood chips and sawdust fran the cabinet.

ae Fram the rear of the cabinet, use a Phillips screwdriver to secure ae Fram the rear of the cabinet, use a Phillips screwdriver to tighten

the four screws, washers, and T-nuts through the newly drilled holes in the display-mounting frame as shown in Figure 11,

the screws until the T-nuts are firmly imbedded in the displaymounting frame as shown in Figure 11.

4, Fran the front of the cabinet, carefully insert the display, with the chassis on the bottam, into the display-mounting frame and onto the four bolts installed in step 2.

\s-" use a 3/8-inch hex driver to secure the display to the displaymounting frame with the washers and nuts supplied in the kit.

  • Connect the 15-pin Molex game connector to the right rear connector on the display chassis,

we Secure the new display bezel to the cabinet with tape or staples. \g.--“Install the display shield and the retainer and grille to the cabinet. Use a 1/8-inch Allen wrench to secure the retainer to the cabinet with the three screws and washers removed previously.

P. INSTALL THE CONTROL PANEL

Perform the following procedure to install the Major Havoc control panel in the game cabinet (see Figure 2). > a 1,-Use a 7/16-inch hex driver to secure the control panel to the cabinet with the three bolts, washers, and nuts removed previously.

Page 39

Major Havoc Installation Instruct ions TM-267

T-Nut Installation

Display Shield

Display Bezel

Figure 11 Installing the Display

Page 40

se Major Havoc Installation Instructions T™M-267

la connect the control-panel harness connector to the game harness. Do

/ not close the control panel. y \oe“Insraxn THE MAJOR HAVOC PRINTED-CIRCUIT BOARDS

Perform the following procedure to install the Major Havoc PCBs in the game cabinet (see Figure 12). s Le Peel the protective backing fran the 1-1/8-inch thick foam pad supplied in the kit.

\2, Fram the front of the cabinet, reach in through the control-panel ~ opening and attach the foam pad to the front wall of the cabinet approximately midway between the upper and lower slotted PCB guides. wt 3 Connect the Conversion PCB to the Major Havoc game PCB edge connectors.

CAUTION

Do not over-tighten the tie wraps to the printed-circuit boards. If the tie wraps are too tight, the Conversion PCB could bow and cause a faulty contact at the edge connectors.

ae Use tie wraps at each end of the PCBs to secure the Conversion PCB

to the Major Havoc PCB. \5e7 Slide the Major Havoc PCB (with the Conversion PCB attached) into the slot closest to the cabinet wall.

v6.--~ Attach the 1/2-inch thick foam pad approximately l-inch fram the top of the Conversion PCB. \1,— Position the PCB mounting bracket in the center of the 1/2-inch thick foam pad and press firmly against the pad.

18... Check that the back edge of the Major Havoc PCB is pressed firmly against the 1-1/8-inch foam pad installed in step 2. Use a Phillips screwdriver to secure the PCB mounting bracket to the cabinet with the pan-head screw. e/ conmnct the top connector on the main harness to the Conversion PCB.

Page 41

Major Havoc Installation Instruct ions T™M-267

¥e-Inch Foam Pad

Tie Wrap

PCB Mounting Bracket

Game PCB

1 %-Inch Foam Pad

Conversion PCB Tie Wrap

Figure 12 Installing the Major Havoc Printed-Circuit Boards

Page 42

Major Havoc Installation Instructions 'T™M-267

to? é

ll. Cut the two tie wraps closest to the bottam connector on the main harness. Turn the bottom connector 180° and attach it to the Conversion PCB. (This will place the red/green wires at pins 1 and 1 and A up. The connector can be attached backwards without causing any damage, but it must be reversed for proper operation of the game.)

Use beaded tie wraps at each end to secure the two edge connectors to the Conversion PCB.

R, INSTALL THE POWER SUPPLY

Perform the following procedure to install the modified power supply into the game cabinet.

Si. Use a Phillips screwdriver to secure the power-supply base plate and power supply to the cabinet floor with the four screws removed previously. “ Qe Connect the game harness to connectors J2, J4A, and J5 on the top of the power supply.

\3., Connect the power cord to connector J1 on the right side of the ~~ power supply. 47 Use a 11/32-inch hex driver to secure the green ground wires to the grounding screw on the power supply with the washer and nut removed previously.

\ sé INSTALL THE FAN

Perform the following procedure to install the fan in the game cabinet (see Figure 10). a” Close and lock the rear access panel,

(2 “Reach through the fan opening in the rear access panel and mark the

4y

Se cabinet cleat at the top and bottom edge of the fan opening.

--Unlock and remove the rear access panel.

Position the mounting block with the side nearest the holes against “the cabinet cleat. Center the mounting block between the two marks made in step 2.

Position the exhaust fan and bracket on the mounting block with the bracket holes aligned with the holes in the mounting block. Make certain that the fan grille is facing the back of the cabinet.

Use a Phillips screwdriver to secure the exhaust fan and mounting block to the cabinet with the two 1-1/4-inch wood screws.

Page 43

Major Havoc Installation Instructions 'TM-267 /

Connect the black and white wires on the fan harness to the two fan power-input terminals.

A Use a Phillips screwdriver to secure the green wire to the fan

/ frame with the self-tapping screw. a 9. Connect the fan harness to connector J4B on the power supply.

T. INSTALL THE SELF-TEST CHART

Staple or tape the Major Havoc self-test chart to the inside of the rear access panel.

U. INSTALL THE LABELS

NOTE

Do not remove or mark any of the existing labels on the game cabinet.

Perform the following procedure to install the conversion kit and FCC conpliance labels on the game cabinet (see Figure 13).

  • Remove the protective backing fran the conversion kit and the FCC campliance labels.
  • Attach the conversion kit label on the back of the game cabinet (directly above the rear access panel).
  • Attach the FCC compliance label over the existing FCC noncompliance label.

V._ INSPECT THE MAJOR HAVOC GAME

Before applying power, perform the following procedure to ensure that the game is modified correctly. ae Carefully check that the conversion has been properly performed.

aR “When you are confident that all instructions were properly followed , close and lock the rear access panel. A 3X” Reach up through the coin-door opening and latch the two springdraw latches to the control panel.

4 Plug in the game power cord.

Page 44

Major Havoc Installation Instructions TM-267

A.

ATARI

whe

This equipment complies with the requirements in Part 15 of FCC Rules for a Class A computing device. Operation of this equipment in a residential area may cause unac ceptable interference to radio and uiring the o} hatever steps ar rrect the interference.

FCC Compliance Label Install over the existing FCC Non-Compliance Label

CONVERSION KIT 1265 Bor! Avenue Sunny:

Conversion Kit No.

Serial No.

120 Volts 60 Hz

Conversion Kit Label

Figure 13 Installing the Labels

Page 45

Major Havoc Installation Instructions TM-267

  • Set the game self-test switch to the on position and perform the self-test procedure in the Major Havoc operators manual (TM-252).

W. ADJUST THE DISPLAY

Perform the following procedures to adjust the display size, centering, linearity, brightness, and color tracking.

X/Y Center, Size, and Linearity

  • Set the game self-test switch to the on position and obtain any of the self-test displays.
NOTE

The horizontal (X) adjustments are located on the Conversion PCB (see Figure 14) and the vertical (Y) adjustments are located on the Major Havoc game PCB (see Major Havoc Operators manual). The X adjustments on the Major Havoc game PCB are bypassed through the Conversion PCB and are not functional when the Conversion PCB is connected.

  • Adjust the X and Y SIZE and CENTER controls so that the white rectangle fills the screen with the corners visible while the red rectangle corners are off the screen.

Brightness

Perform the following procedure to adjust the display brightness.

  • Set the game to the Self-Test Mode and obtain Screen 6, Color Intensity Test display. See the Major Havoc operators manual for a description of self-test operation.
  • Adjust SCREEN (R535) to make the longest white line visible and the white line above the longest line not visible. See the display manual (TM-183) for the location of the SCREEN control.

Tracking

Perform the following procedure to evaluate and adjust the white tracking.

  • Set the game to the Self-Test Mode and obtain Screen 6, Color Intensity Test display. See the Major Havoc operators manual for a description of the self-test operation.
Page 46

Major Havoc Installation Instructions TM-267

Figure 14 Adjusting the Display

Page 47

Major Havoc Installation Instruct ions TM-267

  • Verify that the middle five or six lines are white and remain white as the intensity progresses fram dim to bright (top line compared to bottom line). If€ not, perform the procedure described under Tracking in the display manual (TM183).

X. SET THE OPTION SWITCHES

Verify that the option switches are set to the desired play options for your location. The recommended play options are 2 coins for 5 starting lives, medium difficulty, and bonus life for 100,000 points. Refer to the Major Havoc operators manual for option switch location and setting information.

Y¥. UPDATE THE GAME DOCUMENTATION

We suggest that you keep this document and CO-252-04 for conversion kit parts information. Modify the display manual (TM-183) schematics as shown in Figure 15 (for Versions 2, 3, and 4), Figure 16 (for Versions 1, 2, and 3), or Figure 17 (for Version 4).

Page 48

Major Havoc

se a Xweur == = 7 T 28594 cpg Sa ae moe

nee + '% : = $———— TS R701 Lae dea 7% woe ponmanemenscoraesnoaty RI Hy ik 22% j V4 i +27V—-- +27V wd a i i a eta

cri fore Nia’ ier) ede oa Te Reo! = now Rs 27° fee us as

Y INPUT -~------ o ez + eonrT m7, 25v' ean 67-712 = Installation Instructions TM-267

R2 = misses

Components outlined by a shaded frame have been added per TM-267. Cc]

Figure 15 Input Protection Circuit Schematic (Versions 2,3, and 4)

Page 49

Major Havoc Installation Instructions TM-267

ins Poe

DEFLECTION PCB Pais ; 8 fe $3 -SSse

emnonnemanaenmcna

yenero

are

GENERAL NOTES

1. Resistance values in ohms, % watt, 5%, utr4, AILD.C. voltages are 10% measured trom point6. Z0100-101 uses (66X0040-007) zener diode in

less otherwise noted. K = 1,000, M = 1,000,000 indicated to ground, using @ high-impedance me- series with (340%2331-934) 330-ohm resistor in

2. Capacitance value of 1 or loss is in microFarads,tor. Voltages are measured with no signal inputearly production models.

above 1 in picoFarads, unless otherwise noted. and controls are in a normal operating position. = 7. Use a 4,000:1 probe when measuring G2 (screen)

3. *@900 and @606 are not in High\Voltage PCB,5 Gisied rumtera inca tocafon of wayeformoF focus voltage.

ing. Components identified by shading have special characteristics important to safety and should be replaced only with identical types.

Components outlined by a shaded frame have been added per TM-267. CJ

Figure 16 Deflection PCB Schematic (Versions 1,2,and 3)

Page 50

Major Havoc Installation Instruct ions ™-267

eros “ ail oe 6 oes

te Jel &

Ane woseagorteg (rm wewy

e107

Ube

GENERAL NOTES |. Resistance values in ohms, % watt, +5%, unless otherwise noted. K = 1,000, M = 1,000,000

  • Capacitance value of 1 or less is in microFarads, above 1 in rads, unless otherwise noted.
  • *Q900 and Q906 are not in High-Voltage PCB.
  • AILD.C, voltages are + 10% measured from point indicated to ground, using a high-impedance meter. Voltages are measured with no signal input and controls are in a normal operating position.
  • Circled numbers indicate location of waveform reading.
  • ZD100-101 uses (66X0040-007) zener diode in series with (340X2331-934) 330-ohm resistor in early production models. . Use a 1,000:1 probe when measuring G2 (screen) or focus voltage.

Components identified by shading have special characteristics important to eo Components outlined by a shaded frame have been added per TM-267

safety and should be replaced only with identical types. Components outlined by a shaded frame have been added per TM-267. — Figure 17 Deflection PCB Schematic (Version 4)

Page 51

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 52

T™M-267

To Receive a Free Set of Multi-Color Side-Panel Decals

The multi-color side-panel decals for your Major Havoc™ Conversion Kit were not included when the kit was shipped to you. However, if you want aset, mail this letter to Atari Customer Service and they will send you these decals at no charge, while supplies last. No postage stamp is necessary if mailed in the U.S.A.

The part numbers of the decals are: Left—042421-01, and right—042421-02.

Game Serial No, that was shipped with your kit

Name

Firm

Address.

City State Zip

Area Code Phone

Distributor Operator Other

Page 53

Tape This Edge

. First Fold

| | | | ree necessary if mailed in the United States

as

BUSINESS REPLY MAIL = FIRST CLASS PERMIT NO. 173 MILPITAS, CA SY

POSTAGE WILL BE PAID BE ADDRESSEE es Atari Inc. Ce Attn: Customer Service/Coin-Op Division et 737 Sycamore Drive P.O, Box 906 De Milpitas, California 95035 Pe ua

Second Fold

From:

Page 54

TM-267

To Receive a Free

Input Protection Circuit PCB Assembly

If you have a Wells-Gardner display in your cabinet, the Input Protection Circuit PCB Assembly is required for your Major Havoc™ game. This small “piggy-back” board was not included in your Conversion Kit when the kit was shipped to you.

However, if you need this board, mail this letter to Atari Customer Service and they will send you the Input Protection Circuit PCB Assembly at no charge. No postage stamp is necessary if mailed in the U.S.A.

The part number of the board is A038088-01.

Game Serial No. that was shipped with your kit

Name

Firm:

Address:

city State Zip

Area Code Phone

O Distributor 1 Operator Other

Page 55

Tape This Edge

| | | | ari necessary if mailed in the United States ——e

a

BUSINESS REPLY MAIL a

FIRST CLASS PERMIT NO. 173 MILPITAS, CA a

POSTAGE WILL BE PAID BE ADDRESSEE ee Atari Inc. De Attn: Field Service/Coin-Op Division ee 737 Sycamore Drive PO. Box 906 as Milpitas, California 95035 a

Second Fold

From:

Page 56

TM-267 Ist printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm Distributor

Address G Operator

City State Zip O Other

Area Code Phone

Page 57

‘Tape This Edge

First Fold

necessary if mailed in the United States —e

LL a

BUSINESS REPLY MAIL a

FIRST CLASS PERMIT NO. 173 MILPITAS, CA =

POSTAGE WILL BE PAID BE ADDRESSEE —7~ Atari Inc. a Attn: Customer Service/Coin-Op Division — 737 Sycamore Drive PO. Box 906 Cl Milpitas, California 95035 P| as

Second Fold

From:

Page 58

Atari Customer Service

ga ate A ace ede ek an a laa lal

lem, call TELEHELP® at one of these Atari Customer Service

(Monday-Friday, 7:30-4:00 pm Pacific Time) sz From California, Alaska, or Hawaii (408) 943-1120 From anywhere else in the continental United States ® ineeeon sse16n