Asteroids DP-143-6th-02B
Asteroids (rev 4) (Atari, 1979) · Drawing Package · 1 pages · original scan

OUTPUTS
DIAG STEP (diagnostic PLAYER INPUT CIRCUITRY ‘step), 3 KHz, SELF-TEST SLAM, HALT, FIRE ard a
Ore HYPER inputs are read ‘The THUMP sound is heard throughout play s
he MPU wher SINFO ‘The 585 is connected as an oscillator, enabled porersno (switch input zero enable) is low, Switches to be ‘oad are selected by AEO by N7 pin 2. The frequency is determined by the current coming out of G2. This depends on Its base voltage, which is derived from the four. z20_ tak SI thru AB2 from the MPU. bit code in N7. sesesrfe ‘All inputs. are_read_on seul] r B7. Switch inputs. are ome sree fe lactiies whenupealods ty ‘The SAUCER sound s heard when an enemy
| ine | ground. DIAG ’stEP, ‘9 | ‘saucer appears. The 568 is a voltage-controlled |
| wvrer | Rite and SELF-TEST ‘oe | oscillator. Its modulating voltage is derived |
from the $55. The 555 Is a low frequency Qscilator, The effect Is @ warbling sound. ‘SAUCRSEL changes some component values, In order to provide for 2 different saucer ‘sounds. a signals read by the MPU ace 1d Control the pro. Sedure. SLAM is a signal ‘ead by the MPU to. indicate the status of the antislam switch mounted ‘onthe coin door. The MPU reads HALT to deter- ‘mine the state of the ver: tor generator.
The coin door and some control panel switches are read by the MPU when SINPI (switch Input one enable) is low. p—swrranveren Switches to be read are fe selected by ABO thru ABZ 4} —srvcrrineess oer from the MPU. All inputs = Sauensnden are read on data line OB. Switch inputs are “on when pulled to ground.
M10 latches control signals to tenable different sounds.
‘The Fire sounds for the Saucer andthe *?”
‘Space Ships are gonerated by two Ider |...
| tical | cireite. | aon “contain a 66 | FST |
operating. as a voltage-controlled teliator The Saucer Fiesound Te In {iated by SAUCRFIREEN, and tho Space
| Ship. | Fire. sound | is’ | initiated. | by |
SHBFIREEN, Each of the 3568 10 con
figured in such @ way that when they are
‘enabled, they output a signal of a specific
| fteavency'and amplitude, | This signal | | = | vo,ra] | savcarneen—} |
| Degine | 0 decay immediately, | both in re | = | |
| {ency | and ampitude, | due to the dis | i |
Sharge ofthe contol capacttors (628 & $0 15 Sauoee Fre Sou CA? & 4 for (ees Ship Fire Sound). AS 55x Cuitry.
The game option switches are read by the MPU when OPTS (option switch enable) is low. Switch toggles to be read are selected by ABO and AB1 from the MPU. Switch toggles 1, 3,5, and 7-are read on data line DBO and toggles 2, 4, 6 ‘and 8 are read on DB, Toggle inputs are “on” ‘when pulled to ground.
FE eres ence oy nen ovsion
VIDEO INVERTER
‘The video Inverter circuitry is only used In a cocktall game. In an upright game, pin 19 is unconnected and therefore floats. When pin 19 floats, transistor Q16 is tumed off and transistor Q17 Is turned on, Therefore, INV Is ~82 VDC and NONINV is about +82 VDC. The result Is a nominverted Xaxis and Y-axis output. he ar
‘The EXPLODE sound is _heard when any object explodes. Noise is ‘sampled at a frequency determined by P8, and contol bits EXPITCHO ‘and EXPITCH1. Changing the sampling rate changes the pitch of the ex: plosion. The noise is amplitude- Modulated in R7 by EXPAUDO- EXPAUDS. Ina cocktail game, the wiring hamess shorts connector J20's output pin 7 input pin 18. When the video of Blayer 1 is being displayed, pins 7 and 19 are +5 VOC. ‘This results In a non-inverted video output. When the video for player 2 Is being displayed, pins 7 and 19 are (rounded. This causes transistor 216 to be tumed on and G17 to be tured off. Therefore, INV is +82 VDC and NONINV is ~8.2 VDC. Tho result is an inverted Xaxis and Y-axis ouput, causing the monitor's esplay tobe uP-
R9 and P9 generate random noise. This noise is filtered by P11 and produces the rumble sound heard when the ship is thrusting.
‘Shoot 2, Side B P-14302 6th printing AUDIO OUTPUT
(nap All sounds are mixed in v4 of P11. This is ‘Audio 1. The signal is then inverted by another ‘% of Pit and becomes Audio 2. These cutofphase signals provide a push-pull output o the ‘audio section of the Regulator/Audio PCB.
LAMP, LED, AND COIN COUNTER OUTPUT This circuit consists of coin counter drivers Q11, Q12, Q13 and data latch N11, clocked by the microcomputer's address decoder. When the input 10.a driver is clocked high, its collector goes low, ‘grounding the retum of the coin counter in the coin ‘door. When START! or START2 is clocked low, it ‘grounds the START LEDs in the control parel. -——{S]uerr cow Tore ce com Ty
ow +a LIFE sound is heard when an extra life is, gained. It is merely 3 KHz from the clock cir-
‘The reference designations, used in the cit: cuit descriptions, refer to the ‘01 thru 04 PCB. assemblies only ‘at location O11 on PART OF REGULATORIAUDIO PCB
‘Audio inputs AUDIO 1 and AUDIO 2 Nove: receive out of phase signals for pust-pull AUDI AMPLIFIER Is PART'OF REGULATOR/AUDIO. operation. AUDIO DISABLE is perma: PCB AND IS REPEATED ON SHEET 1, SIDE A. ently grounded fer continuous audio ‘amplification.
suse a}
‘The video output ciroult consists of three individual circuits; X axis, ¥ axis, and Z axis video output clcults. The X axis and Y axis video output circuits each consist ofa digital to-analog converter (DAG), currentovoltage converter, two sample and holds, and ‘amplifier, The Z axis video output circult consists of a shift register and a summer. X and Y Outputs ‘The DACs (011 and B11) each receive binary numbers from the vector generator’s pos!tion counters outputs. These numbers represent the location of the beam on the monitor. For the non inverted X axl, the numbers range from 0 to 1023, where Os at the far left of ‘the monitor screen, 512 atthe center, and 1023 is at the far right, For the non-inverted Y axis, the numbers range {rom 128 to 996, where 128 is at the bottom of the monitor Sereen, 61218 at the center, and 996 is atthe top. When the X axis and Y axis are inverted, tthe monitor picture is tured upside down. Ths is used for a two-player cocktail game. ‘The DACs convert these binary number inputs to current outputs. The DACs! current outputs are applied to the pin 6 Inputs of current-to-voltage converters C12 and A12.
From the current-iovoltage converter, the signal Is fed to two sample-and:nola cir cuits: One is nominverted and the other is inverted. The non-inverted sample and hold ‘consists of one stage of analog switch D12 and capacitor C98 for the X axis, and B12 and ‘C106 for the ¥ axis. The inverting sample and hold consists of inverter E12, one stage of ‘analog switch D12, and capacitor C119 for the X axis and B/C12, B12 and 118 for the Y axis,
‘The sample and hold circuits are controlled by SHCON (sample and hold contro). ‘SHCON is derived by gating 3 MHz from the microcomputer clock circuitry and VGCK* from the vector generator’s state generator. The result of these inputs insures that the ‘ominverted and inverted analog signals that are applied to the analog switches have sutficiently stabilized before being applied to the sample and hold capacitors.
‘The output swing of SHCON is 8 to +8 VDC. When SHCON is high, the voltage ‘charges oF discharges the sample-andhold capacitors to the X and Y analog voltage ‘value, The voltages are then applied to the inputs of the second analog switch. These ‘witches select ether the non-inverted or inverted Xaxis and Y-axis outputs. The outputs {are then amplified by the second stages of C12 and A12 for an impedance-matched out: put to the X and ¥ inputs to the monitor, Since the monitor doesn't have field-adjustable X and Y gains, the gains are adjustable by variable resistors R120 and R126.
Z Output
‘The Z axis video output receives six inputs. BVLD (beam valid), from the output of the vector generator’s position counters, tells the 2 axis to draw the line. BLANK (vector line blank, from the vector generator's state machine tells the Z axis to stop drawing a line. ‘SCALED thru SCALES (grey level shading scale, from the output of the vector generator’s data latch, tells the Z axis the grey level shading of the line that is being drawn on the ‘monitor.
|When BVLD and BLANK are both high, a high is clocked through shift register K9 that tums transistor G3 off. This allows the scale inputs to be passed through transistor Q2. When BLANK goes low, a low Is clocked through K®, transistor G3 turns on, and the signal is grounded at the base of transistor 02. ‘The scale inputs at the base of transistor Q1 determine Q's emitter voltage, during the line draw period. The SCALEO thru SCALES resistors R36 thru R29, resistor R35, and resistor R40 resuit in arange of about + 1.0 VDC when al are low and + 4.0 VDC when all {are high. The emitter of Qt follows at about + 1.7 to 4.7 VOC, while the emitter of tran- Sistor Q2 follows at about + 1.0 to 40 VOC. This output is applied to the Z input of the ‘monitor. Since there are brightness and contrast controls inthe moniter, there are no ad- Justments in this circuit.
Sheet 2, Side B ASTEROIDS Switch Inputs, Coin Counter, LED and Audio Outputs Section of 034986-01 thru 04 G 03498605 and -06 I ATARI
(© 1979 Att, re.