UFO Robo Dangar
Ufo Robo Dangar (4/09/1987) (Nichibutsu, 1986) · Manual · 12 pages · 4 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
USER INFORMATION
F.C.C. REGULATION COMPLIANCE
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS “A“ computing device pursuant to subpart J of part 15 of F.C.C. rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
F.C.C. requires that the STICKER that comes with the KIT must be on the back of your machine or elsewhere visible when inspected.
SERVICE INFORMATION
NICHIBUTSU will, repair and exchange parts or replace P.C.Board in the event of manufacturing defect for ninety day warranty period after original purchase with Nichibutsu. ~ Mail-in service can be obtained during the warranty period by sending the product postage prepaid, to the nearest distributor or NICHIBUTSU USA CORP. (California). A purchase receipt or other proof of of date of original purchase will be required before warranty performance is rendered. It is important that the enclosed registration card to be filled out entirely and sent in for your protection in case of product failure . SEND IN THE CARD TODAY!
ae HOw TO PLAY
*x Control the LEADER With 8 way joystick .
* Use FIRE button to destroy all flying enemies and
ground fortresses .
- As FLYING CAPSULES appear , destroy them and as each new COMPONENT is freed - dock with it !
- Each component increases the combined firepower or special powers of entire ship . LEADER is the main ship and equipped with double forward cannons.
- Use TRANSFORM button after each component is added for greater fire power . Components will be transformed into a flight formation and shoots beams in multiples .
- Only after all three components are docked , player will become UFO ROBO DANGAR and can retrieve awesome desolation gun . UFO HANGARS will now appear , destroy hangars and dock with UFO for super fire power formation.
- The number of times that you can transform into formation is indicated by F at the bottom center of the screen .
POWER SUPPLY
This P.C.Board requires power supply of
- +5 V5 A (+ 2%) for game logics
- +12 V 1A (+ 10%) for audio IC only
It is very important that exactly + 5 V_ to be attained and checkd at the edge connector pin # 10 (positive) and pin # 15 (negative) with a voltmeter .
COIN COUNTER
DANGAR logic board is designed to use with 5 Vor6V type counter , absolutely NO 12.V or 24 V type counter should be used . ts Some uprights havea 12 V counter connected directly to coin switch which will destroy the IC at location 6E & TE , so please check the connection of the counter very carefully before power is turned on .
- If 12 V counter is used : Don't connect counter directly to COIN SW ( pin # H ) Connect counter to COUNTER 1 ( pin # V ) Disconnect diode Di & D2 on logic board Connect a diode parallel with counter as figured below Pwo
+5Ve +12 3
X (3.cut off) (4.add)
- If 5 V counter is used ;
Disregard this figure .
TILT SwWiTCcH
TEST SW
It is your option to have a TILT SWITCH in the machine. TEST lead ( pin # U ) could TILT SW be connected to a TILT SWITCH as figured at right.
an
A B Cc D E F H J K L M N P R Ss T U v W x Y Z
ODIAMDRAAWNYE p1-UP w/brown pl - LEFT w/orange pl- SHOOT w/green p2 - UP p2 - LEFT p2 - SHOOT COIN 1 w/purple GND GND black +5 V red +12V yellow
+5 V red GND black GND black 1 player brown TEST/Tilt orange COUNTER 1 w/gray SP (+) w/blue
GREEN GND black DOWN RIGHT TRANSFORM DOWN RIGHT TRANSFORM
2 players SERVICE COUNTER 2 SP (-) RED BLUE SYNC
KIT CONTENTS
NICHIBUTSU PRINTED CIRCUIT BOARD FCC STICKER . MARQUEE PLEXI GLASS WIRING HARNESS 8-WAY JOYSTICK . BUTTON / SWITCH ASSEMBLY CONTROL PANEL OVERLAY . SERVICE INSTRUCTION Q PRA ERR
20K & every 60K 20K & every 90K 50K & every 60K 50K & every 90K
Demo Sound WITH WITHOUT
TABLE UPRIGHT
Difficulty EASY HARD
Screen Inversion
Continue NONE 3 Times 5 Times 99 Times OFF OFF ON OFF OFF ON ON ON i
& TEST MODE
Connect TEST lead from edge connector (pin # U) to a toggle switch . When TEST SW ON , the screen will display as shown .
ss SOUND TEST 4% no. ass SUITCH TEST **hpa OF KK ADJUSTMENTS &« ba :
Game adjustments are made HI
with DIP SWITCH bank 1 and 10 bank 2 on the CPU board.It @1SES NMIHOABUSSAD CO.LTO. is recommended to increase BONUS level each step after several weeks on the same location.
DIP SW. 1 DIP SW. 2 duyogggg| | sgggggug **k SOUND TEST *%« Move joystick UP & DOWN , listen for the music, adjust the volume located below edge connector.
***k SWITCH TEST **x Shows all the functions of joystick , buttons and DIP SWITCHES. Any CLOSED SWITCH will be indicated in RED as ON on the screen.
PUSH 1 is SHOOT button PUSH 2 is TRANSFORM button
CONTROL PANEL
- Remove control panel buttons and joysticks . Clean and sand old vinyl or remove old vinyl and clean with thinner.
- Drill the holes as needed and file the new holes smooth .
- Peel off the backing paper from our new overlay and expose the adhesive. Heating of the overlay adhesive and/or your control panel recommended in this procedure. Carefully place the overlay on top of your control panel Try not to leave any bubbles under the overlay.
- Use a razor knife to cut holes for buttons & joysticks To avoid cutting a wrong hole , mark it before cut .
- STICKERs of FIRE and TRANSFORM : a. could be stuck on control panel , then put a plexi glass on top . b. could be stuck under the monitor glass at bottom to be corresponding to the buttons .
- Stick the PLAY INSTRUCTION CARD under your monitor glass
MARQUEE HEADER
A lexan marquee with adhesive on the back and a clear plexi glass are provided. You can either:
- Expose the adhesive and place it on the plexi glass so the lexan part will be on outside .
- Put Super Glue on 4 corners of lexan and place it facedown on plexi so the lexan part will be inside . Peel off the back paper if you want to light up the DANGAR Marquee .
Control Shaft ———~
Washer —_-@) |
Flat Surface Adapter Plate SS
Mounting Plate
Actuator — i E-Ring is
CONTROL MARKETING Joystick # 50-4508
To remove control shaft :
- First remove E-Ring .
- Then pull control shaft out of Mounting Plate .
8 Way Joystick
POSSIBLE 1 & 2 PLAYER LOCATIONS
MONITOR
The P.C.Board in this kit can be used with :
- Any VERTICALLY mounted Raster Scan Monitor .
- Negative Composite SYNC (sychronization)
Wires of the new harness to the monitor are color coded to indicate as: RED , BLUE , GREEN video signals to the monitor . BLACK is used for GROUND ( 0 V ) WHITE is for NEGATIVE SYNC .
Attach the wires from the P.C.Board to the monitor’s main circuit board as shown below .
*KfFor WELLS-GARDNER MONITOR Se *KLor ELECTROHOME MONITOR
NEG. HORZ. SYNC white jumper NEG.VERT.SYNC -|] 0 |---------------- > pin #22:SYNC
GROUND ---black jumper-----7---> # 2:GROUND
POS .HORZ.SYNC (o} POS. VERT. SYNC oO GROUND O}---black wire------ BLUE VIDEO O}---blue wire--- ----> #21: BLUE GREEN VIDEO O|---green wire-- -> # Y:GREEN RED VIDEO OQ|---red wire------------ > #20:RED
TROUBLE SHOOTING
NO SOUND & NO PICTURE
- Check +5 Volts at pin #10 (plus) and pin #15 (minus) with a voltmeter.
- Check voltage supply for monitor AC 100 or 120 Volts.
- Put Credit and push 1 PLAYER, start the game and check if you get sound or not.
WITH GAME MUSIC but NO PICTURE
- The problem could be your MONITOR.
- Check 5 wires : RED,BLUE,GREEN,SYNC and monitor GND.
- Check AC voltage supply for monitor.
- Replace monitor if necessary.
. WITH PICTURE but NO SOUND
- Check two wires lead to SPEAKER (pin #19 and #U).
- Make sure both SP(+) and SP(-) are isolated from GND.
- Check +12 Volts at pin #12.
. GARBAGE SCREEN DISPLAYED
- Adjust POWER SUPPLY to have just +5 Volts at pin #10.
- Check if any E-PROM chips are loose from the socket.
PICTURE SCROLL
- Recheck connections of SYNC and GND between MONITOR and edge CONNECTOR.
- Change SYNC polarity on your monitor POSITIVE to NEGATIVE.
PICTURE UP-SIDE-DOWN x Switch #6 of BANK 2 will inverse the screen .
Nichibutsu
x HH KRALAKRSMITSEI2HOS DPE Ay 2ak-vay HEAD OFFICE 12-9, 1-chome, Tenjindashi, Kita-ku, Osaka Japan RR SRM PRAPRAGRMEMH TESS rovasac (M=FFALR AMABTRONSIZTT AI REVCAVY ay GRAFTIAM BAM SEM SR-4-17 RARE IF NichbutssUSACop. BTW7S.Gerteld Ave Unit 18 Paramount,Calt, 0723US A BW ae mA At TH 06 1353-5211 (tC) F530 FAX. ( 06 )356-1531 3 06 1351-3841 TELE X 523-6891 NCBCOL J (03 664-5271 (10) F103 FAX. (03 661-1326 (011824-2571 (tt) F062 FAX. (011)824-2584 2 (092) 472-7221 tt) F812 FAX. (092)472-7222 EH 213) 408-0515 FAX (213) 408-0208
Nichibutsu U.S.A. Corp. 15737 Garfield Ave. Unit #18 Paramount, CA 90723
“SERVICE : (213) 408-0518