CATHODE RAY TOMES

Top Gunner

Jackal (World, 8-way Joystick) (Konami, 1986) · Manual · 16 pages · 36 sections · original scan

Page 1

Supplied By Shane R. Monroe (webmaster@monroeworld.com) “<p KONAMI.

fp Konami* is a trademark of Konami Industry Co., Ltd.

Page 2

Conversion Kit Contents. . weneee inside Cover 56 Pin Wiring Harness Color Code

Introduction..........

Graphics.............

Monitor Specifications ................0. 3 Dip Switch Setting............

Monitor Information... . TABLE OF CONTENTS

Page

Lee ee eee eeeeeaee 1 36 Pin Wiring Harness Color Code

beeen eee eens 2 Wiring Diagram ...............

beeen wena d meee aed User Information Warning.......

Stereo/Mono Sound Installation ........... 5

REPLACEMENT ACCESSORIES ARE AVAILABLE THROUGH YOUR DISTRIBUTOR. CONVERSION KIT CONTENTS:

MAIN PRINTED CIRCUIT BOARD P.C.B. CAGE (FCC REQUIRED) CONNECTING WIRING HARNESS 6 SETS — BUTTON ASSEMBLIES TWO 8-WAY JOYSTICKS MARQUEE (HEADER) (1/8” acrylic sheet) ONE SET SIDE PANEL GRAPHICS (left & right) CONTROL PANEL OVERLAY CONTROL PANEL DECALS instruction decals/button decals (2 sets) MANUAL © REGISTRATION CARD

THIS KIT USABLE IN AN UPRIGHT WITH A VERTICAL MONITOR. *THIS KIT NOT INTENDED FOR COCKTAIL MODEL CABINETS.

Page 3

TOP GUNNER: INTRODUCTION

KONAMI CONVERSION KITS: are the most complete conversion kits. available today. Every detail has ‘been carefully considered, designed and packaged to provide you the means of easily producing a professional:.conversion.

These kits have all the accessories to easily convert your UPRIGHT video game.

We strongly urge you to FULLY. STUDY this instruction manual BEFORE you begin your conversion. It contains step-by-step instructions, schematic diagrams and suggestions on how to install your Konami Conversion Kit and maximize your profits. TOP GUNNER can be installed in any vertically mounted rastar scan monitor game.

Everything you. will need to construct your new game.is provided. inthis kit. All. accessory parts — wiring harness, joystick, etc. are custom made for TOP GUN- NER by top engineers experienced in the coin-op industry. An 8-way joystick with rotary switch (as provided) MUST be used.

The Player Instruction and Button Control decals are made of a non-destructible acrylic material specifically to keep. the player from peeling them off. Should you convert.a cocktail table. game, TOP GUNNER is supplied with 2 sets of button decals.

  • * * IMPORTANT NOTICE x x x

The Japanese Amusement Machine Manufacturers Association (JAMMA) has introduced a new standard in video game P.C.B.’s. It was decided that all new products from any JAMMA member will use the same pin print-out on the edge connector. The edge connector will have 56 pin outs, 28 per side.

Konami Inc. will offer a 56 to 36 pin adaptor P.C.B. available through your distributor. This new adaptor P.C.B. will enable the new 56 pin out to adapt to Konami’s old standard 36 pin out. ©

* * * STEREO SOUND x x x TOP GUNNER offers stereo sound in this kit

TOP GUNNER offers stereo sound in this kit. Please see page 5 for proper installation.

Page 4

PUTTING YOUR BEST GAME FORWARD

PREPARATION: For best results, all old graphics should be removed completely from the cabinet. “Stick-on” graphics can be removed by using a hairdryer or hot air device. The heat from the dryer will loosen the adhesive, allowing you to easily peel them off — any adhesive residue can be cleaned off with acetone and a soft dry. cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT.) TOOLS YOU NEED:

  • Foaming Aerosol (such as “Windex”).
  • Soft Squeegee.
  • X-Acto Knife.

SIDE PANEL DECALS

  • Spray area of cabinet where Side Panel decals are to be applied with foaming aerosol or a mild soap solution. . Remove protective backing from decals. . Position decals into place. . With a soft squeegee, beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish.
  • Allow to set approximately 2 to 3 hours before handiing. Maximum adherence is achieved in 48 to 72 hours. Pon
  • Trim side decal to fit your cabinet.

CONTROL PANEL OVERLAY:

  • Refer to Recommended Control Panel Layout on page 1.
  • Drill any new holes needed.
  • Plug any holes that will not be used. (A permanent epoxy filler works well for this step.) .
  • Pre-position the overlay prior to removing the backing.
  • Slowly apply the overlay — inch by inch on the control panel, removing the backing as you apply it.
  • Once it's in place, by- using an X-Acto knife, cut around the button and joystick placements.

INSTRUCTION/ BUTTON DECALS: Apply the Player Instruction, Button and 1 Player/ 2 Player decals in their respective positions. Apply pressure liberally. Allow to set as long as possible before putting game on location.

NOTE: Maximum adherence is achieved in 48 to 72 hours.

FCC WARNING LABEL: ; FCC Warning Label must be applied to the outside o the cabinet near the line cord entry.

MARQUEE

(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE)

1/8” Acrylic Marquee should be cut to fit your game. DO NOT remove protective mask until this‘is done. One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish). CUTTING WITH A KNIFE OR SCRIBER Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind — a scribing knife such ag the one pictured, a metal scriber, an awl, or even a sturdy craft knife — to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in. place: It is best not to remove the protective masking. Make the cuts caréfully. using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then clamp the acrylic sheet or hold It rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.

Break sheet over edge of table after scribing.

P.C.B. CAGE INSTALLATION

Konami, Inc. now supplies a new style P.C.B. cage which is superior to old style cages because of ease of installation. The cage is made of a 32 point stem-stock which is fire retardant. TO INSTALL THE CAGE:

  • Open cage bottom and secure to desired P.C.B. position.
  • Install printed circuit board inside cage using wood screws, screwed through the cage bottom into cabinet side.
  • Close the cage over printed circuit board and secure with latch on cage.
Page 5

TOP GUNNER: 36 PIN WIRING HARNESS

36 Pin Wire Harness Supplied in TOP GUNNER you will find a 36 to 56 pin card connector. This connector enables the operator to convert his Konami wired video cabinet from the old 36 pin harness to the new JAMMA standard 56 pin connector without major rewiring.

If this kit is to be installed in a non-Konami -gwired cabinet a wiring harness is supplied.

36 to 56 Pin Adaptor Card

Solder Side Parts Side WIRE COLOR KEY: : WHITE/GREEN (NOT USED) +12V DC ORANGE RED/GREEN *(Mono Speaker Output) |B | 2 | *(Mono Speaker Output) ORANGE/GREEN

YELLOW/RED2PGuN|c | 3 | 2P MISSILEORANGE/YELLOW
BROWN/YELLOW2PLertT|D | 4 | 2P RIGHTBLUE/YELLOW
VIOLET/WHITE1PSTART|E | 5 | 2P STARTVIOLET/YELLOW
ORANGE/WHITE1P MISSILE | F | 6 | 2PUPBLACK/YELLOW
RED/WHITE1PGUN | H | 7 | (NOT USED)ORANGE/GRAY
BLUE/WHITE1PRIGHT|J | 8 | 1PLEFTBROWN/WHITE
BLACK/WHITE1PUP|K | 9 | 2P DOWNGRAY/YELLOW
RED/GRAYCOIN’ | L | 10 | COIN2BLUE/GRAY
GRAY/WHITE1P DOWN | -M | 11 | COIN COUNTER 1GREEN/GRAY
PINK/WHITE(NOT USED) | N | 12 | COIN COUNTER 2YELLOWIGRAY

GREEN/BROWN — VIDEOGREEN | P | 13 | VIDEO BLUE BLUE/BROWN

RED/BROWNVIDEO RED | R | 14 | VIDEO SYNCWHITE/BROWN
WHITE/BLACK(NOT USED) | s | 15 |PINK/YELLOW

BLACK GROUND | T | 16 | GROUND BLACK

BLACK GROUND BLACK

RED +5V DC RED

(BASE COLORILINE COLOR) “SEE PG. 5 FOR SPEAKER WIRING

Page 6

TOP GUNNER: 56 PIN WIRING HARNESS

Solder Side WIRE COLOR KEY:

BLACK BLACK BLACK BLACK

RED +5vDC| c | 3 | +5VDC RED RED +5vpc| 0 | 4 | +5vDC RED

ORANGE ORANGE

WHITE/RED COIN COUNTER2| J | 8 | COIN COUNTER 1 WHITE/BLACK

(EMPTY) cc (EMPTY)

WHITE/GREEN(Mono Speaker Output)WHITE/BLUE

(EMPTY)

GREEN/WHITEVIDEOGREEN | N | 12 | VIDEO REDRED/WHITE

WHITE VIDEO SYNC | P | 13 | VIDEO BLUE BLUE/WHITE

YELLOWIBLACK—-SERVICESW|R | 14 | VIDEO GROUNDBLACK

(EMPTY) S48 | (EMPTY) YELLOWI/RED YELLOW/BLUE WHITE(VIOLET) 1P START (plow nlc CORED ACK (WHITE/BROWN WHITE(GRAY) 1P DOWN <YELLOW GRAY 1P LEFT YELLOW/GREEND 1P RIGHT CORANGEBLUE __ | 1P SHOOT CGRAVIBLACK cis 1P SHOOT 2 GRAY/ | NOT USED )

NOT USED NOT USED BLACK BLACK BLACK BLACK

(BASE COLOR/LINE COLOR)

Page 7

DIP SWITCH SETTINGS

DIP SW No. 1 Settings Coin 1 Switch Set

COIN Coin 2 Switch Set

7 mT 7

7 7

7a nN TNyo;7 nT mn n mT

fo) i = OFF

| ON |

| OFF | OFF

| ON | | ON | fe) z ° fe) fe} mu n n n n mn

  • DIP SWITCH NO. 2 SETTINGS

THE NUMBER OF PLAYER'S LIFE {e) . z

O!lo/O giclg slele

A [oF | OFF | on | oFF | 50,000 | 250,000 | | on | 30000 | NA | | ON | BE mI nN

50,000

NORMAL | OFF |

| on | on | very oiFFicuT | *SW 3 NOT USED

DIP SWITCH NO. 3 SETTINGS

VIDEO SCREEN FLIP

NORMAL

UPSIDE DOWN

*SW 2, SW 3, & SW 4: NOT USED

¢ SHOWS NORMAL SETTING

Page 8

TOP GUNNER: MONITOR INFORMATION

SERVICE INSTRUCTIONS

NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every time the monitor is turned on.after being off for a minimum of 5 minutes. Should any part of the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT face and alt surrounding metal parts. Then slowly withdraw for a distance of 6 feet before turning off.

1.0 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not ~ need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished).

2.0 VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions.

3.0 CIRCUIT PROTECTION A 4.0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit.

4.0 FOCUS Adjust the focus control, located on the HV unit (T352), for maximum over-all defination and fine picture detail.

5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short. -

6.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control.

7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U” or “D”.

8.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video Is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions “R” or “L”. 9.0 HORIZONTAL WIDTH ADJUSTMENT . The horizontal width coil is a hexagonal tuning tool adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.

  • KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MONITOR.

19". REO 19 ~orive GRN DRIVE REO CUTOFF GRN CUTOFF: BLU CUTOFF

*NEG H SYNC *NEG V SYNC

NOTE: WHEN USING COMPOS ITE SYNC USE HORIZ. SYNC INPUTS, POS H SYNC POS V SYNC HORIZ. WIOTH GNO COIL BLU HORIZ HOLO

BLK LEVEL

TPS

HORIZ VERT VERT VERT HORIZ CENTERING SIZE HOLD RASTER RASTER SHIFT SHIFT

FIGURE 1

Page 9

TOP GUNNER: MONITOR SPECIFICATIONS

TOP GUNNER requires a vertically mounted monitor. It also generates composite negative sync. If your monitor is composite positive sync, you will have to change to composite negative sync.

  • To alternate composite positive sync.to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the output pin from the P.C.B. is a combination of H-sync and V-sync.
NOTE: Please refer to Figure 2.

FIGURE 2: +5V

FROM P.C. BOARD

NEGATIVE COMPOSITE SYNC. OUTPUT TO MONITOR (PIN 14 on P.C.B EDGE) POSITIVE COMPOSITE SYNC.

(+ 5V and GND should be taken out of the P.C. Board.)

. (2) Separate Syne modification for TOP GUNNER if your monitor has “Separate Sync” input. (For example “Electrohome brand” and “Wells-Gardner brand.”) Step 1 WIRING HARNESS te ee ee ee ane

VIDEO SYNC

If the picture is still not stable... Step 2 Prepare Hook-up wire to seperate -H and -V sync. signals.

WIRING HARNESS

VIDEO SYNC

SVCN4P

Page 10

1P-SHOOT3

1P-SHOOT2

1P-SHOOT1

1P-DOWN

1P-UP

1P-RIGHT

IP=LEFT.

2P-SHOOT3

2P-SHOOT2

2P-SHOOT1 2P-DOWN 2P-UP 2P-RIGHT 2P-LEFT 2P-START 1P-START SERVICE COIN2 COINI 2P-SW8 2P-SW7 007343 Aa +5

Al2 All ycc aio uo f19 Ag.9 S44 ape AT 12D AB =U33 macs he

[Nos O ola a]<r]o9] INXCS 144 nioc 5 “NRMW 123 twes t 143 y501 -) A10 ~ =

a ea 29209 aac =e a=

005273 Sing yal CRAG Li A3 y¥3} = SS is B33

4i._ 005885 vCr3 vcr2 i vert > vCFO e vep3 b> veB2 fe vest 12 veo vCD3 vcp1 loo ycoo -— wo} OcF3 cre OCF @cFO @CB3 OcB2 @cB! OcBO =I2\eh fe ets

Page 11

2P-SW6 2P-SwW5 eP-SwW4 2P-SW3 2P-SwW2 2P-SW1 1P-SW8 1P-SW7 1P-SW6 1P-SW5 1P-SW4 1P-SW3 1P-Sw2 1P-SW1

DIPSW1

o~e o~e mi) PS P3 P3

005273 6) ES + RAI IJRA2. 2KX8 I x) = augue [7 ax

an Se Lee

oes jean aml at Sr a ae ee 7 ? ‘ ms)

L$139 sai 40 fae fre eee ee Te, 4 a

A 6809E HALT

2 52555 be heen i) I (ey rR) Fees BLSRRARS

105 120 135 LA4445

*12v GNO_GND

125 140 . 1UCK34 i 6 { oe 43 os a ee ar

3] 12 L) q

Page 12

A14 ANZ AN oholes ocean

AS =e az

MASK1M

INXCS -—NIOC 53) 005885 88888 i INRMW Fs

INWCS as So i)

IN501 588sess HT ala ¢| if fi 5 9

(sa ras i

Page 13

JOVSYNC INC 5 9g

oOm= BSSasecteas

‘b 69 93 81 105 115 125 140 120 135 83) Pex PI P3 KEL56P CN13P

44% 44 ee

YNC VCC(+5V) +12V GND NC

* KINDS OF CAPACITOR

> TANTAL

: MYLAR

> ELECTRIC > CERAMIC

JAMMA EDGE S6PIN

PIN NO.

NUMBER:

ALPHABET : SOLDER-S

PART ae tbe /A/ & SMALL LETTER 4P-CONNECTOR !

13P-CONNECTOR

1P_ROTARY SW,SOUND

2P ROTARY SwW.SQUND 4P-CONNECTOR MONO 4P-CONNECTOR STEREO 0 | Konami

KONAMI INDUSTRY CO. “Lo. |Pes-714 SCHEMATIC DIAGRAM [ee [Bes [DESIGN|

DRAW | CHECK |APPROVE SVCN4P CN13P a * rs IDAKA | IDAKA

RELEASE NAME GX631 — pwe3020678 DATE ed eee 101006

CODE NO. ie 3G H [ J

Page 14

TOP GUNNER: STEREO/MONO SOUND INSTALLATION

Konami introduces stereo sound. Please read instructions carefully. If your video cabinet doesn’t utilize two speakers, follow instructions for mono output.

_ Stereo Output Connector B13P

HOW TO CHANGE TO MONAURAL/STEREO

*Note: Mono & Stereo sound cannot operate simultaneously. For Mono Sound Use pin #10 and Pin L of the 56 pin edge connector to the speaker contacts. Also connect Jumper connector to mono B4P. Use left hand volume control to adjust sound level.

For Stereo Sound Use pin 1 and 2 of connector B13 for . right speaker. Use pin 3 and 4 of connector B13 for left speaker. Change jumper connector to stereo B4P. Jedwne vq 0281S NX sedwine dyg Ou; *

CUSTOM

CUSTOM

Page 15

TOP GUNNER

WIRING: DIAGRAM --

REQUIRED POWER CAPACITY

+12V

PARTS SIDE

“STEREO

a —. POWER

-} suppLy EE Con oa = | C@IN couNTER! la |

corn eounter2 ===} —— RED

COLOR MONITER “hue

SYNC... GN |

SERVICE pes COIN2

CONTROL FOR QP

ONLY FOR TABLE TYPE

CONTROL FOR 1P

JAMMA —S6PIN EDGE CONNECTOR mx. 5 O—Osgot2 1P_yp 5/32 INCH PITCH . SHOOT [iP DOWN Cy RIGHT Hee TISPEAKER AIG - NOTES - 1 1P NO.1 PLAYER

a HIE S80 peu [IP SHoOT? L_41GNO 2 SURGE KILLER DIQDES FOR COIN —— COUTER INSTALLED ON THE P.C.B

Page 16

USER INFORMATION

WARNING

F.C.C. REGULATION COMPLIANCE

THIS KIT IS INTENDED FOR USE ONLY ON COIN-OPERATED VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983 WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE- QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A COMPUTING DEVICE.

IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTER- FERENCE TO RADIO AND T.V. RECEPTION, REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE.

THE P.C. BOARD CAGE SUPPLIED WITH THIS CONVERSION . KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION.

agp Konami.

815 Mittel Drive, Wood Dale, Illinois 60191 Telephone: (312) 595-1443, Telex: 6871385 KONAM UW, Fax: (312) 595-2973 For Technical Assistance Call Toll Free (800) 222-6181 (Outside Illinois)