CATHODE RAY TOMES

Tokio

Tokio / Scramble Formation (newer) (Taito Corporation, 1986) · Manual · 16 pages · 14 sections · original scan

Page 1

Romstar, Inc. 3043 Kashiwa Street, Torrance, CA 90505 Phone (213) 539-2744 Fax (213) 539-3626 Telex 182426

Licensed From TAITO ™ All Rights Reserved ©1986

Page 2

1 Installing and Servicing Your

AG

New Game Package

Table of Contents

New Game Package ContentS.. 0.2.0.6 c cece eect ee treet ete t eee 2

Power and Monitor Requirements ...... 60. eee eee ete eee teens 2

Recommended Tools and Supplies... 0.0.6... cece eee eee eee 3

Dip Switch Tables ...... fo eae eee eT Hiei Se Ques oe EE Eee ERE aD 3&4

Game Operation 0.0... cect eet teen ent nee 5

Installation Procedures .. 1... . cece cece eee eet tee 6

Control Panel PositioNiINg .. 0... cece eee cette ene 12

Main Harness Connections ..... 0... cece ee eee ee eee eens outside back cover

Page 3

Ad

NEW GAME PACKAGE CONTENTS

1 Main Printed Circuit Board (PCB) 1 Marquee 1 PCB Cage (FCC Required) 1 Control Panel Overlay 1 Set Legs, Bolts, & Spacers 1 Plex Control Cover 1 Connecting Wire Harness 1 Set Side Graphics 1 Eight-Way Joystick 1 Set Play Instructions & Function Labels 6 Player Button Assemblies 1 Service and Installation Manual

Note: Replacement accessories available through your exclusive Romstar distributor.

POWER REQUIREMENTS MONITOR REQUIREMENTS

+5 VDC +12 VDC 7 amp minimum lamp minimum Vertical Mount Raster Scan Negative Composite Sync

Page 4

Recommended Tools and Supplies

ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 1/4” © 7/16" Drill Bits 1/4" Plex Bit 1-3/16"” Chassis or Sheet Metal Punch 1 1/4” Plex Hole Saw Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Patience Common Sense

Dip Switch Tables

Optimize Your Profits Painting Supplies (if you do your own painting) Paint Brush and Paint (don't forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Night’ Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32" © 1/8” © 3/16” Masking Tape 3 12" OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)

Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren't running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!

Page 5

Dip-Switch Bank A

Adjustment Options 1 Game Style Table Upright * Picture Normal * Invert

Test Mode Normal Test Attract Sounds on off Coin! 1Coin 1Credit 1Coin 2Credit

2Coin 1Credit 2Coin 3 Credit 1Coin 1Credit * 1Coin 2Credit 2 Coin 1Credit 2 Coin 3 Credit

  • — Factory Setting

Dip-Switch Bank B Fajustment Options REESERKSEAKS Difficulty Few Enemies — Few Shots Many Enemies — Few Shots * Few Enemies — Many Shots Many Enemies — Many Shots on | a

Bonus100,000/400,000off | offoy
200,000/400, 000on|of||D>

300,000/400,000 off | on

400, 000/400, 000on | onEe

Number of Planes 3 off | off 9

  • — Factory Setting
Page 6

——_Game Operation

TOKIO

£ Hit Red Planes And Capture Them To Gain Fire Power.

~ Press Both Fire And Formation Buttons Together To Launch Captured Planes As Powerful Missiles. = Capture 2 Or More Red Planes And You Can Change Formations And Types Of Fire Power.

Air To Air Air To Air Air To Ground

And Only Only

Air To Ground —— = Aas AS AS ree = as

£ Destroy Big Battleship By Hitting 3 Engines With Air To Ground Missiles.

£ Only 4 Extra Fishters Can Be Used At One Time —Others Are Stored For Future Use.

Page 7

Installation Procedures

Something To Think About Your final product will be anew game. You have made a wise decision to transform a game that has seen better days in the all important cash box into a new game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end result is... amew game ata very low cost. Fact: Spend a little time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of a new game package. The new game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary g/itches do not occur. Remember: You are creating a new game . If you have any questions or just need some advice on any of your new game transformations, don’t hesitate in giving a member of our technical staff a call.

Let’s Get Our Hands Dirty

Preparing the Original Game for the New Game

Remove the following:

1,Main logic board{s)4.Monitor Bezel
2.Control panel5.Marquee
3.Monitor plexiglass6.Graphics

| would recommend painting your cabinet to give it a fresh new look. (If it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with laequer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.

Page 8

Time To Install Your New Goodies

Before You Start. ..Remember DO NOT Do This Work With The Power On!

Logic P.C.B. Cage

Mount the logic cage securely (away from power supply). A_ Mark and drill pilot holes (3/32”). B Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C Install the PC.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots int he cage bottom.

Note: Leave the cage cover off until you have attached the entire wire harness and have tested the game for proper operation.

Wire Harness

Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.

Connecting the Wire Harness to the Existing Wires

When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors. 1, Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.

  • Solder the new wire designated for that position to the original wire you just stripped.
Warning: DO NOT JUST TIE THE WIRES TOGETHER. THIS CAN CAUSE NAGGING INTERMITTENT PROBLEMS THROUGH LOOSE CONNECTIONS OR OXIDATION OR BOTH. Always take the time to do it right.
  • Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
  • Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a mew game , not a sloppy conversion.

Power Wires

  • Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
  • You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don’t overload the edge connector pins and cause them to “burn”.
Page 9

Monitor Wires

You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.

NOTE. . .CONCERNING SYNC: Your new game only calls for one sync wire connection, this is called composite syne (horizontal and vertical tied together). This composite sync is also negative. Most monitors have supply positions for both negative and positive sync. You can check your monitor manual or call our technical department for assistance.

Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.

Coin Door Wires

  • Connect the designated wires to the coin switches and meter.
  • Youcanconnect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
  • Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.

GUESS WHAT? You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.

Smoke Test

What Test? Don't worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.

  • Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
  • Make sure the logic board, board cage, monitor and power supply are securely fastened in place.
  • Double check the connectors to be sure they are wired and connected properly.
  • Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for ‘DEMO WITH SOUND”. This will enable you to hear as well as see that your new PC.B. is functional.
Page 10

Time to Apply Power:

1. 2. Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED) Listen for game sounds. If after one minute you have not heard any sounds: A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C} Check the +12V power supply to the logic board.

NOTE: If you do get sounds, but they are a little fuzzy, switch the wires around on the speaker. How is the monitor image? A) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative). If your monitor does not have dual polarity positions for sync, then you will need to reverse the sync yourself by installing a simple one I.C. circuit between the logic board and the monitor. (The following illustration shows a hookup for both composite and separate syncs.

HORIZONTAL SYNC INPUT FROM P.C.B, 5 Vcc {OR COMPOSITE SYNC INPUT) HORIZONTAL SYNC OUTPUT TO MONITOR ff {OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM P.C.B

VERTICAL SYNC OUTPUT TO MONITOR

B) Now how’s your picture? © It it centered? ® Is it too bright or dim? Is it in focus? Check your monitor manual for these adjustments. If your screen looks “‘off”, then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. C) Is the picture upside-down? Dip switch 2 on switch bank A should solve your problems.

Page 11

Control Panel Assembly

2. Remove the buttons, joysticks and wire harness and put them aside fro now. Do not remove the original panel overlay until the new holes have been drilled. Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that your new game investment is well worth protecting. . .and the contro! panel is the first place to show wear and tear. © You will need to cut this piece to size. Use the control panel as a template. © Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass. Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes. Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter. The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file. Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peel off the bottom half and do the same as you did for the top. Adhere the instruction and function labels. Install the Plex Control Cover over your completed new game panel.

Note: Be sure to bolt the plexiglass securely to the panel. Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible)

Marquee Installation

Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on a new game. Take your time ... Don’t forget this is going to be a new game.

Page 12

Side Graphic Installation

Be sure sides of game are clean and free of old adhesive, dust, etc. Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet). Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing. Remove any small bubbles with a pin or razor blade (pop theml)

Finishing Touches

1.

2. Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can’t get a coin into it. Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking. Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game . © Are all the player controls working?

  • Are the game sounds present?
  • Is the volume level proper?
  • Are the dip switches set properly? Well, that’s about it. Good Luck.
Page 13

8 WAY JOYSTICK CHANGE FORMATION CHANGE FORMATION

POSSIBLE 1 & 2 PLAYER LOCATIONS

Control Panel Positions

INCREASE

VOLUME

PCB Layout

Page 14

WARRANTY, REPAIR AND RETURN POLICY

1 *45 DAY FULL PARTS WARRANTY.

2 *60 DAY FULL ELECTRONICS WARRANTY (SEE RMA BELOW).

  • MINIMUM $40.00 SERVICE CHARGE FOR ALL NON-WARRANTY REPAIRS OR RETURNS.
  • ANY UNAUTHORIZED NON-FACTORY REPAIR OR ATTEMPTED REPAIR VOIDS WARRANTY.

(*ALL WARRANTY PERIODS BEGIN ON THE DATE OF PURCHASE FROM ROMSTAR)

RETURN MERCHANDISE AUTHORIZATION — (RMA}

  • ALL RETURNED MERCHANDISE MUST HAVE AN RMA NUMBER CLEARLY VISIBLE ON THE OUTSIDE OF THE PACKAGE.

2 ALL RMA NUMBERS MUST BE OBTAINED FROM ROMSTAR BY AN AUTHORIZED ROMSTAR DISTRIBUTOR. (PLEASE HAVE ROMSTAR SERIAL NUMBER AVAILABLE WHEN CALLING FOR AN RMA #).

  • ALL PC BOARDS RETURNED TO ROMSTAR WITHOUT AN RMA NUMBER WILL BE SUBJECT TO A MINIMUM CHARGE OF $40.00.
  • ROMSTAR WILL SHIP ADVANCE REPLACEMENT BOARDS TO DISTRIBUTORS OR AT DISTRIBUTORS REQUEST, DROP-SHIP BOARDS DIRECT TO THE OPERATOR.
  • ADVANCE REPLACEMENT BOARDS WILL BE BILLED TO THE DISTRIBUTOR UNTIL RECEIPT OF A RETURNED BOARD BY ROMSTAR AT WHICH TIME A CREDIT WILL BE ISSUED.

6 ALL REPAIRS AND/OR REPLACEMENTS WILL BE SHIPPED BY ROMSTAR WITHIN 24 HOURS OF RECEIPT OR REQUEST. (SUBJECT TO AVAILABILITY OF BOARDS).

  • FORANY ROMSTAR PRODUCT PURCHASED AFTER 3/1/86, A ROMSTAR WARRANTY CARD MUST BE ON FILE FOR EACH BOARD TO FACILITATE REPAIR & RETURN.

ANY QUESTIONS CONCERNING THESE POLICIES SHOULD BE DIRECTED TO DENNIS SABLE, TECHNICAL MANAGER OR SHAWN ZENKER, OPERATIONS OFFICER.

Page 15

TOKIO WIRE HARNESS (G)

COMPONENT SIDE SOLDER SIDE

Ground _ Ground Video Red Video Ground Video Green Video Blue Video Sync Not Used

st

Coin Switch Coin Meter

Service WU) Slam Switch 2P Select

COMPONENT SIDE TOKIO WIRE HARNESS (H)

WIRE | CONNECTION COLOR

BlackGround1
BlackGround4
Red+5VDC5

Red +5VDC

-5VDC +12VDC (unreg) Ke Key __ +12VDC Ground Ground Ground

2|2| c

a fe) a : ee Cc

: 2\2| qc Z| Cc +5VDC +12VDC (unreg) and +12VDC may be wired together.

Page 16

*kKKKEEKSERVICE BULLETIN* ******%

SUBJECT: "Tokio" Coin Switch Jumper

If you wish to use your "Tokio" conversion without a coin meter,

a small wire jumper must be installed across the points of J7

located near IC 60 (the large brown SIP IC near the "G" connector)

METER HOOK-UP: Connect 1 lead of the meter to terminal 9 of the

"GM

oq"

The

the connector and the other lead to terminal 9 (+12VDC) of the

connector. coin meter is activated by the voltage (@+6VDC) dropped from

+12VDC through a resistor.

BEST REGARDS

ROMSTAR

TECH. DEPT.