CATHODE RAY TOMES

Rastan

Rastan (World Rev 1) (Taito Corporation Japan, 1987) · Manual · 9 pages · 2 sections · original scan

Page 1

Taito America Corporation 660 S. Wheeling Rd Wheeling, IL 60090

660 S. Wheeling Rd.

(312) 520-9280

Page 2

GAME INSTRUCTIONS

Taito America Corporation's "RASTAN"™ game.

You are Rastan, a medieval warrior who must defend himself in a mythical world filled with adventure and excitement. Along the way Rastan will encounter special treasures for additional strength and power. Use these treasures to your best advantage. There are 3 scenes consisting of 6 patterns each for Rastan to conquer. Not until Rastan conquers the castle king can he proceed to the next scene. Excellent graphics with scrolling backgrounds plus exciting sound provide for hours of entertainment and continued earnings.

*Use joystick to move Rastan

*Use SWORD button for his sword

*Use JUMP button to jump

This manual will guide you in the conversion of your color monitor upright video game into a "RASTAN"TM game. We urge you to read through the instructions before beginning the conversion.

WARNINGS AND NOTICES

For safety and reliability, Taito America Corporation does not recommend or authorize any substitute parts or modifications of Taito America Corporation equipment.

Use of non-Taito America parts and modifications of game circuitry may adversely affect game performance and safety.

Substitute parts or equipment modifications may void FCC acceptance. Since "RASTAN"T™! is protected by Federal copyright, trademark and patent laws, unauthorized versions of this game are illegal under Federal Law. This also applies to unauthorized facsimiles of Taito America equipment, logos, designs, publications, assemblies and games (or features not deemed to be in the public domain) whether manufactured with Taito America components or not.

Page 3

NOTICE

Parts salvaged from your old game are required to complete your kit. These salvaged parts MUST operate perfectly, or the converted game can not perform properly or safely. Always repair circuit board malfunctions and cabinet damage before conversion is attempted. Check the parts supplied in this kit against the parts list included in this manual.

CAUTION

For safe operation it is recommended the game be grounded. This game should be equipped with a three conductor power cable, The third conductor is the ground conductor and when the cable is plugged into an appropriate receptacle, the game is grounded. The offset pin on the power cable's three-prong connector is the ground connection. Do not use an adapter plug to defeat the ground pin on the power cord.

NOTICE

This kit is not intended for use with X-Y¥ monitors. Suitable monitors are the horizontal or vertical raster-scan with inputs for red, green and blue video as well as negative sync. (These should be compatible with TTL logic levels.)

Note: "RASTAN"™ uses a horizontal monitor.

NOTICE

Be sure the power supply from your old game is capable of +5 vde regulated at 6A; +12 vde regulated at 1A and -5 vde regulated at 1/2A. These operating voltages are necessary for your kit.

Page 4

TAITO AMERICA CORPORATION KIT PARTS PROVIDED

1-*RASTAN"™™ pC BOARD ASSEMBLY

1-8 WAY JOYSTICK ASSEMBLY

1-"RASTAN"T CONTROL PANEL OVERLAY

1-"pasTAN"™ MONITOR COVER PLEXIGLASS

1-"RaSTAN"™™ MARQUEE

1-WIRING HARNESS

1-INSTRUCTION CARD WITH REMOVABLE CONTROL STICKERS

2-BUTTONS

1-FCC CAGE

2-PCB MOUNTING BLOCKS

TOOLS AND SUPPLIES REQUIRED

SCREWDRIVER WIRE CUTTERS ELECTRIC DRILL WITH BITS SOLDERING IRON AND SOLDER PLIERS PHILLIPS SCREWDRIVER HEX DRIVER 188-GRIT SANDPAPER GREASE PENCIL OR MARKER X-ACTO KNIFE HACKSAW, JIGSAW OR TABLESAW W/CARBIDE-TIPPED BLADE ELECTRICAL TAPE OR HEAT-SHRINK TUBING

All games require a certain amount of maintenance to keep in good condition. A periodic check of mechanical controls would be beneficial to guarantee your game will be profitable.

GAME PREPARATION

CLEANING

The exterior of the game, all metal parts and all plastic Parts can be cleaned with non-abrasive cleaner. Caution should be used when cleaning the plastic. A dry cloth can cause scratches and result in a foggy worn appearance. Plexiglass cleaner on a soft cloth is suggested to maintain and keep your monitor crt cover looking new.

Page 5

CABINET

Inspect your cabinet for any gouges or items stuck on the cabinet like chewing gum. Remove all foreign objects and fill in the gouges with any type of quick hardening wood putty. Sand to ensure the surface is smooth. Wipe the outside of the old cabinet clean. Remember the reason you are converting your old game is to have the earnings of a new game. Making your game look like a new game will increase your earnings and spark player-interest.

NOTICE

Please make sure you clean and lubricate the coin mechanisms. It is important that you service them in order for this game to achieve the maximum possible earnings.

CONVERSION INSTRUCTIONS

Remove the new "RASTAN"™ marquee from the kit. This new marquee provided with your kit is specifically designed for ease of, handling. Place and center the old marquee on top of the new marquee. Place masking tape on the area where you intend to cut the new marquee. Using an x-acto knife score the new marquee and simply break at this score. If your old marquee is made of glass, remove the paint of the old marquee and attach the new marquee behind this glass. If your old marquee is made of plexiglass, it is recommended that new clear plexiglass be used to best provide the brilliance of your new marquee.

Remove the new “RASTAN"™ monitor plexiglass from the kit. Place the center of the old monitor glass on top of the new monitor plexiglass. Place masking tape on the area where you intend to cut the new plexiglass. With your grease pencil draw a straight line to use as a cutting guide. Using the hacksaw or jigsaw cut the plexiglass down to size.

CONTROL PANEL

Remove the old control panel buttons or joysticks. Clean and sand smooth any imperfections on the existing lexan material.

Place the template provided in this manual on the control panel to design the best possible positioning for your buttons, joystick and control panel instructions.

Page 6

Leave your 1 and 2 player start buttons where they are on the old control panel. (Use the enclosed 1 and 2 player stickers if needed.) Drill holes as needed for installation of the joystick and other buttons. Clean any burrs from around holes. Any hole that is no longer needed we suggest plugging with wood, putty or epoxy.

Remove any soil and/or grime from the front of the old control panel lexan. Cut the new "RASTAN"™ lexan to the appropriate size needed to cover the panel. If possible, leave enough lexan to wrap a small lip around the top and bottom of the panel. Remove the backing from the "RASTAN"™ lexan and apply it over the old control panel being careful to avoid air pockets.

After the lexan is securely on, with an x-acto knife or razor blade cut the holes on the control panel. Install the new joystick, buttons and any hardware that might have been removed on the control panel and tighten them down.

Attach the additional stickers marked "Sword" and "Jump" to the control panel.

ADDITIONAL GAME PLAY INSTRUCTIONS

Your new monitor plexiglass has instructions on it. If when installing the new monitor plexiglass it becomes necessary to cut through the instructions, place the additional set of instructions on the monitor plexiglass.

WIRING PROCEDURES

INSTALLING INTERBOARD WIRING

This game comes with a color-coded 3 connector cable for easy installation. Refer to the wiring diagram included in this manual for quick connections.

Disconnect the old wiring harness from the old CPU board.

Carefully remove old circuitboards and FCC cages from the game.

Using the schematic drawings from your old game, carefully

note the function of each wire.
Page 7

Leaving several inches of wire from the old wiring harness at each connector, cut the wires near the game's coin door, monitor, control panel, power supply and speaker wires. Install the new wiring harness to those points following your wiring diagram. Use electrical tape or heat-shrink tubing to insulate all splices.

Install your FCC cage where the old board set was.

Mount the "RASTAN*™ pcp assembly with the mounting blocks provided in the center of the FCC cage. Plug the wiring harness onto the PCB and close the cage securely.

If your game has seriespass transistors for the power supply on a separate heatsink, remount the metal heatsink beside the power supply board.

Check and clean the input jack on the power supply board. Replace any burned or damaged pins.

GAME PLAY AND DIP SWITCH SETTINGS

*pasTaN" has been designed with dip switches for operatoradjustable features for maximum earnings in your location. Using the dip switch chart provided in this manual will allow you to customize the game for your location.

If done properly your game should look new. The conversion is complete.

WE APPRECIATE YOUR PURCHASE OF TAITO AMERICA'S "RASTAN"™

KIT AND SINCERELY HOPE THAT THE GAME PROVIDES

MANY HOURS OF CONTINUED EARNINGS AND ENJOYMENT

FOR YOU AND YOUR PLAYERS.

PLEASE LOOK TO TAITO AMERICA CORPORATION TO ALWAYS

PROVIDE THE VERY BEST IN VIDEO ENTERTAINMENT FOR YOU!

Page 8

RASTAN™ KIT DIP SWITCH SETTINGS

SWITCH BANK “1"123«56 7 8

een eee pt a ca an

UPRIGHT MODE|on |i]||!]]]
COCKTAIL MODElorr ||||I!l!
MONITOR REVERSE|lorF |||||||
]lon |!II!I|
NORMAL GAME|!{OFF ||
TEST MODEi]i]jon ||III]
|!|OFF |OFF |OFF |OFF |
!|1ON JOFE JON |OPF |
|||OFF |ON |OFF |ON |
||lon JON JON |ON |

2 CREDITS

SWITCH BANK °2"12 34 5 6 78

EASIEST ION |OFF | EASY lOFF |OFF | DIFFICULT lorry |on | HARDEST lon jon |

BONUS PLAYER: lOFF {OFF | ! |on |OFF | I |orF JON | | lon jon | |

3 PLAYERS|i]|||OFF |OFF |
4 PLAYERS!|||lon |OFF |
5 PLAYERS!||IlorF |on |
6 PLAYERSi]1I!lon lon |}
CONTINUE MODE ONI!||||lorF |!
CONTINUE MODE OFF]i]!Ii]i]lon |I
NOT USEDi}|I!III|OFF |
FACTORY SETTINGS1234 5 678

1ON JOFF |OFF |OFF [OFF |OFF [OFF |OPF |

Page 9

(4) 2218 DIA

1,000 DIA JOYSTICK TEMPLATE FIGURE 3