CATHODE RAY TOMES

Hydro Thunder 25in

Hydro Thunder (Midway Games, 1999) · Manual · 105 pages · 59 sections · original scan

Page 1

NOVEMBER 1999 MID WAY 16-20040-101 ™ GAMES ian G

UPRIGHT DEDICATED VIDEO GAME 25” CABINET

CE. LISTED

Operations Manual Includes

@ Installation @ Operation @ Testing & Problem Diagnosis @ Parts Information @ Wiring Diagrams @ Product Service

Midway Games Inc. 3401 North California Avenue Chicago, Illinois 60618-5899 USA http://www.hydrothunder.com

Page 2

HYDROTHUNDER |

CHAPTER

ONE

PRODUCT SAFETY, SPECIFICATIONS, SETUP, & MAINTENANCE

NOTICE: This manual is subject to change without notice. MIDWAY reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.

Fill out and mail in the Game Information Card. Include the game serial number from the label on the rear of the cabinet. For your records, write the game serial number in the manual. SERIAL NUMBER

Setup 1-1

Page 3

Setup 1-2

Page 4

SAFETY INSTRUCTIONS

The following safety instructions apply to operators and service personnel. Read these instructions before preparing the game for play. Other safety instructions appear throughout this manual.

DEFINITIONS OF SAFETY TERMS

DANGER indicates an imminent hazard. If you fail to avoid this hazard, it WILL cause death or serious injury.
WARNING indicates a potential hazard. If you fail to avoid this hazard, it COULD cause death or serious injury.
CAUTION indicates a potential hazard. If you fail to avoid this hazard, it MAY cause minor or moderate injury. CAUTION also alerts you about unsafe practices. NOTICE indicates information of special importance.
WARNING: TRANSPORTING GAMES. This game contains glass and fragile electronic devices. Use appropriate care when transporting this game. Avoid rough handling when moving the cabinet. Do not move this game with the power on.
WARNING: DISCONNECT POWER. Always turn the power OFF and unplug the game before attempting service or adjustments unless otherwise instructed. Installing or repairing PC boards with power ON can damage components and void the warranty.
WARNING: GROUND GAMES. Avoid electrical shocks! Do not plug in a game until you have inspected and properly grounded it. Only plug this game into a grounded, threewire outlet. Do not use a “cheater” plug, or cut off the ground pin on the line cord.
WARNING: AVOID ELECTRICAL SHOCKS. This video game system does not utilize an isolation transformer. Internal cabinet AC is not isolated from the external AC line.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.
CAUTION: CHECK POWER SELECTOR, LAMP. Set the 115/230VAC selector on the power supply for the correct line voltage. Check the selector setting before switching on the game. Verify that the fluorescent lamp assembly is correct for the local line voltage.
CAUTION: USE PROPER FUSE. Avoid electrical shock! Replacement fuses must be of the same type as those they replace. Fuse voltage and current ratings must match ratings on the original fuse. PPPLIG @ Bre
CAUTION: ATTACH CONNECTORS PROPERLY. Be sure that printed circuit board (PCB) connectors mate properly. If connectors do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Connector keys only allow a connector to fit one set of pins on a board.

Setup 1-3

Page 5
CAUTION: USE CARE WHEN SHIPPING HARD DISKS. The hard disk drive must be packed in an anti-static bag. When shipping the drive for repair or replacement, pack it in an approved container (P/N 08-8068). Do not stack or drop hard disk drives.
WARNING: HAZARD TO EPILEPTICS. A very small portion of the population has a condition which may cause them to experience epileptic seizures or have momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition.

If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), immediately consult your physician before using any video games. We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.

Setup 1-4

Page 6

PRODUCT SPECIFICATIONS

Operating Requirements

Location Electrical Power Temperature Humidity

Domestic120VAC @ 60Hz4.0 Amps32°F to 100°FNot to exceed 95% relative

Foreign 230VAC @ 50Hz2.0 Amps = (0°C to 38°C) Japan 100VAC @ 50Hz 4.0 Amps

Cabinet Statistics Shipping Dimensions Shipping Weight

Cabinet Cabinet

Width 32.0" (81.3 cm) Boxed 328 Ibs. (149 kg.) Depth 66.5" (169 cm) Height 76.0" (193 cm)

Equipment Characteristics

Video Display MonitorAudio SystemCurrency Acceptors
Medium Resolution RGBDigital Stereo Sound2 Coin Mechanism, Coin Counter
25” (63.5 cm) CRTTwo 5.5” (14 cm) andDollar Bill Validator Ready

One 6.5” (16.5 cm) Spkr —_ Electronic Coin Acceptor Ready

Game Characteristics

Player VariablesOperator VariablesDiagnostics
1 to 4 players per game (with linking)Coinage, Game OptionsAutomatic Power-Up Self-Test
Choice of craft and courseDifficulty, Force, Volume,Manual Multi-Level Menu System

High Score Recognition Audits, Statistics

PRODUCT CONFIGURATION

@ Stand Alone Units Each game is ready to play right out of the box. Operators may use the menu screens in the game menu system to determine some player variables in advance or leave the choices up to the players.

@ Linked Units Linking allows players to compete against each other (on one course). Operator menus are the same as in stand alone games. Crossover couplers and linking cables to connect two games are factory installed. Use the optional Hub Linking Kit to interconnect up to eight games (two groups of four).

MAINTENANCE

@ Viewing Glass It is not necessary to switch off power to the game to clean the glass. Apply a mild glass cleaner to a clean cloth or sponge, then use this to wipe the viewing glass. Do not apply the cleaner directly on the glass! Liquid could drip down into switch or control circuits and cause erratic game operation.

@ Player Controls Use plastic-safe non-abrasive cleaners to avoid damage. Apply cleaner to a clean cloth or sponge, then use this to wipe the player controls. Do not apply the cleaner directly on the controls!

Cabinet Use plastic-safe non-abrasive cleaners to avoid damage. Apply cleaner to a clean cloth or sponge, then use this to wipe the cabinet. Do not apply cleaner directly on artwork or cabinet!

Setup 1-5

Page 7

GAME SETUP

WARNING: The cabinet is top heavy. Use the two handles on the back of the cabinet when moving the game.
  • Remove all items from shipping containers and set aside. Casters, levelers, and mounting hardware are packed with the pedestal section. Inspect the exterior of the cabinet for any signs of damage.
  • Remove the keys from the steering wheel. Unlock and open the coin door and cash box. Remove the rear door. Inspect cabinet interior for any signs of damage. Check all major assemblies to assure that they are mounted securely. Ensure that nothing blocks fan airflow.
  • Electrical cords and game spare parts are in the cash box. Locate the casters and levelers first. ‘ INET SHOWN FOR REFERENCE

01-9359 (~~ WHEEL BRACKET

4108-01219-11 8x1 6 PIN-HD-AB—— SPECIAL

20-8712-37__ . E" RING a 20-9627 WHEEL

INSTALL CASTERS

  • Fasten caster wheels to their wheel brackets with caster shafts and e-rings. Mount the two wheel brackets to the bottom-rear of the game cabinet. Each bracket requires four screws.
  • Install one nut onto each leg leveler. Tilt as needed to locate four threaded holes under the cabinet. Install a leveler and nut into each hole. Do not tighten nuts at this time.
  • You can install an extra padlock to secure the rear door. You'll find a hasp in the spare parts bag. Remove the two lock bracket nuts from inside the cabinet, above the rear door opening. Slide the hasp onto the bolts so that it protrudes from the hole in back of the cabinet. Reinstall nuts and tighten.

RRISGE OLT

—— NUT

CABINET SHOWN FOR REFERENCE |

Page 8

INSTALL THE DOOR LOCK AND SECURITY BRACKETS

  • Modify the lock plate at the top of the rear door. Remove the bolts and nuts from the lock plate. Rotate the plate so that the slot will be above the door. Reinstall the bolts and nuts and tighten firmly.

RECEPTACLE

PANEL FUSE— HOLDER

LINE CORD 2

REFER TO (¢ APPLICATION CHART:

INSTALL THE POWER CORD

  • The power cord is with the spare parts. Match the holes on the IEC plug with the prongs in the receptacle. Push the plug firmly to seat it. Route the cord away from cabinet wheels and foot traffic areas.
  • Refer to the game's Cabinet Wiring Diagram in Chapter 5 and check to see that all cable connectors are correctly secured. Inspect for damaged connectors. Be sure that you DO NOT FORCE CONNECTORS. Most connectors are keyed to prevent making reversed connections.
CAUTION: CHECK POWER SUPPLY LINE VOLTAGE SELECTOR SWITCH. Set the 110/220 VAC selector on the power supply for the correct local line voltage. Check the selector setting before switching on the game.
  • Reinstall the rear door and close it. Lock the rear door and remove the key. If required, install the extra padlock through the hasp. Install the screws at the top and sides of the rear door. Tighten the screws snugly. Close and lock the cash box and coin doors.

NOTICE: Tamper-resistant screws and a matching wrench are provided with this game for additional security. Four tamper-resistant screws and a wrench are located in the spare parts bag. If desired, replace the original screws with the tamper-resistant screws. Tighten the screws firmly with the wrench.

  • Move the game to its play location. Lower each leg leveler until the cabinet is stable and level. Adjust the levelers as required to raise wheels and distribute weight equally on each corner. Tighten the nuts.
  • Plug the game into a grounded (3-terminal) AC wall outlet. Switch on the game, using the on/off switch at the top-left rear of the cabinet. The game will power up and begin self-diagnostics. If diagnostics find no errors, the game enters its Attract Mode of operation.
  • Unlock and open the coin door. Locate the control switches. Press TEST MODE to enter the Menu System.
  • Follow the on-screen instructions to select the Diagnostics Menu, then choose Hard Drive Tests. Perform each of the routines to verify hard disk drive operation. If no errors are found, the program should function well.
  • Return to the Diagnostics screen, then choose Monitor Patterns. Use the various patterns to verify that the monitor is properly adjusted.

Setup 1-7

Page 9

20.

21. . Return to the Diagnostics screen, then choose Switch and Lamp Tests. Follow the on-screen instructions to verify that each of the controls and lights is operational. If no errors are found, the controls should function well.

. Return to the Diagnostics screen, then choose Stereo Sound Tests. Follow the on-screen instructions to verify that each of the speakers is operational. If no errors are found, the audio should function well. . Return to the Diagnostics screen, then choose Force Feedback Tests. Follow the on-screen instructions to verify that steering resistance is present. If no errors are found, the aim should be good. . Return to the Main Menu screen, then choose Calibrate Steering and Throttle. Follow the on-screen instructions to set steering and throttle limits. If no errors are found, the controls will have the maximum accuracy. Return to the Main Menu screen, then choose Start the Game. The game will automatically enter its Attract Mode of operation (scenes and sounds from typical races, players’ scores, messages, etc.). Insert currency or tokens and play a game. Change the volume and make any other adjustments. Install the rear door. Close and lock all doors. Tighten the leveler nuts and engage the caster locks.

Setup 1-8

Page 10

HYDROTHUNDER™

CHAPTER

TWO

OPERATION, FEATURES, AUDITS, & ADJUSTMENTS

NOTICE: This manual is subject to change without notice. MIDWAY reserves the right to make EF improvements in equipment function, design, or components as progress in engineering or a manufacturing methods may warrant.

Operation 2-1

Page 11

GAME OPERATION

DESIGN PHILOSOPHY This game uses an “Arcade Computer” to control its functions. The “Arcade Computer” is a hybrid cross between the custom game computer circuits used in most games and the personal computers found in many offices. The “Arcade Computer” uses a familiar case enclosure with a motherboard, plug-in cards, a modular power supply, disk drives, etc., but it has been optimized specifically for playing this game. This design permits improved upgrade and service access without sacrificing game ruggedness or reliability.

PLAYER CONTROLS

« BOOST Button This button allows a player to begin or continue play, select tracks and boats, etc. If the Boost feature is active, this adds a burst of power (the button is illuminated when Boost is available during a race). An on-screen gauge shows exactly how much Boost fuel has been collected by a player.

« THROTTLE Lever Controls craft speed. Push up to move forward, down to back up. Stop is a detent position in between. Reverse is spring loaded, but forward speeds may be maintained without attention (cruise).

@ STEERING WHEEL The steering wheel is used to aim the craft. It provides course condition feedback to the pilot.

@ HIGH View This button gives a distant aerial view of the track. The position is from above and behind the boat. This is what a helicopter camera would see.

« LOW View This button gives a close up aerial view of the track. The position is from above and behind the boat. This is what a boat camera would see.

« PILOT View This button shows the cockpit view. The position is from the driver’s seat inside the boat. This is the view through the windshield as seen from normal driving perspective. 7 MOLDED

THROTTLE LEVER

PUSHBUTTON(RED) IEW-HIGH”

=STEERING WHEEL

PLAYER CONTROL LOCATIONS

Operation 2-2

Page 12

OPERATOR CONTROLS

CABINET CONTROLS

«# The DIP Switches set some system variables. You can set other variables in the menu system.

# The Monitor Remote Control Board allows you to adjust the video display for optimum viewing.

# The Cabinet POWER Switch turns off the entire game, but does not reset game variables.

# The Computer POWER Switch turns off the computer. It is internally located. Use it for servicing.

CONTROL SWITCHES

« TEST MODE Button causes the game to enter the menu system. Press the TEST MODE button briefly to run automatic tests. Or, press and hold TEST MODE Button until the Main Menu appears. Within the menu system, the TEST MODE Button’s function is described on each screen.

@ VOLUME DOWN and VOLUME UP Buttons adjust the game sound levels. To make minor volume changes, press either button briefly. To make major changes, press and hold a button. In the menu system, VOLUME UP and VOLUME DOWN moves the item selector through each of the menus.

« SERVICE CREDITS Button allots credits without changing the game's bookkeeping total. SERVICE CREDITS Button functions in the menu system are also described on each screen.

( »)) NOTICE: The Attract Mode volume level is separate from the Game Mode volume level. ad For greater profits, raise volume levels to add realism and draw attention to this game.

(ae eo ra tet

care = + ear

NTROL SWITCHES

[1 fa Azo ITEM ow EME: i PEL

COUNTER

OPERATOR CONTROL SWITCH LOCATIONS

Operation 2-3

Page 13

GAME FEATURES

STARTING UP

Each time the game is first turned on or power is restored, it begins executing code out of the boot ROM. These self-diagnostic tests automatically verify and report condition of the CPU and the game hardware. If any of the individual tests fails, the game may display an error message. Once all Power-up tests are complete, the game goes into the “attract mode”. Scenes and sounds from a typical game alternate with previous high scores in an endless pattern until game play starts. Insert currency to start the game. Players select a boat and a track. Play begins after a countdown period. The game will progress until time is exhausted or play is over. If no more play is required, the game automatically returns to the “attract mode”.

GAME RULES Play instructions are on the information panels over and under the video monitor.

INDIVIDUAL PLAY Insert currency to start the game. Select a boat and a track. Additional game information appears on the screen when needed. Individual statistics are shown periodically during the race and its end. PLAYER CHOICES Any boat can be used on any track. Each boat handles and performs differently. Players will learn which boats are best for a given track and driving style. Press one of the VIEW buttons to select more boats. CONTROLLING THE BOAT The steering wheel and throttle control the boat. The steering wheel directs the boat while the throttle sets its speed. A “BOOST” button on the throttle gives an extra burst of power. This button flashes when the additional “BOOST” is available. In order to use “BOOST,” players must collect “BOOST” icons along a track by steering directly under them. A gauge shows exactly how much “BOOST” power is available. INDICATORS On-screen indicators give the players information about their boat and those of competitors. Across the top of the screen are numeric indicators for elapsed time, time remaining to pass the next checkpoint, and race position. Gauges show engine R.P.M., vehicle speed, and “BOOST” fuel remaining. DISPLAYS A superimposed radar map shows the terrain and the position of all boats, with your craft at the center. Computer-controlled boats are shown as green triangles, other human-piloted boats are shown as red triangles, and police craft are shown as blue triangles. At the bottom of the screen, another display shows the relative position of nearby boats. GAME ACTION Action begins when the three-two-one countdown ends and the announcer yells “Go!” Boats must pass checkpoints within time limitations to continue play. Players must avoid fixed obstacles and other boats to decrease their time between checkpoints. Ramps along the route allow players to advance more quickly, collect hovering “BOOST” icons, or avoid obstacles. Players can change their view of the action by pressing the view buttons on the left side of the control panel. The game includes announcer comments, engine sounds, and other noises. SCORING Players who set a speed record for any track may enter their initials in the high score table. After a certain number of tracks are completed (determined by the adjustments), additional tracks become available.

Operation 2-4

Page 14

MENU SYSTEM

SYSTEM OVERVIEW A series of on-screen menus present game variables and diagnostics. The Main Menu screen allows the operator to view information, make changes, or verify equipment operation. Each Sub Menu screen displays one specific group of choices. Detail Menus present data or run the required tests. You must be at the Detail Menu level to detect errors, make changes, or activate tests. The operator control switches are used to move through the menus, select items, and start or stop particular routines. Each time the game is turned on or switched from normal play mode to the menu system and back, the startup routine is activated. These basic system checks run automatically; their purpose is to detect those faults that would prevent the game or the menu system from operating properly. Messages appear on the screen as each item runs, including any error information. Successful startup takes less than one minute to complete. Write down any messages or information before proceeding to the menus or game play. SCREEN LAYOUT Each menu screen is different, but the material presented stays in the same physical location each time. The color bar at the top center of each screen displays the current menu title. The center of the screen shows data (menu items, video signals, statistics, reports, etc.) The bottom of the screen displays messages (explanations, control functions, revision levels, etc.) ORGANIZATION The operator must activate and deactivate the menu system manually using control switches. The Main Menu screen items are divided into categories: tests, statistics, audits, adjustments, etc. Tests can verify proper operation of the equipment assemblies one at a time. Other items allow operators to assess game performance and customize or return to factory defaults. Sub Menu screen items present the operator choices within a category. Some items have no Sub Menu while others may have more than one. It is always possible either to return to the previous menu or go on to the next menu. The instructions are usually listed at the bottom of each individual screen. Detail Menu screen items display specific information. The operator must command the system to get results or to make changes. There is always a way to go back to the previous menus from this screen. Switch functions are listed on each screen. Use the control switches to highlight an item on any menu. Only one highlighted item can be selected at a time. Press the indicated button to select a highlighted item. To return the game to normal play mode, use the switches to return to the main Operator Menu and select START THE GAME, then press TEST. The menu screens will be replaced by the “Attract” scenes.

Operation 2-5

Page 15

OPERATOR MENU

mIDway

DIAGNOSTICS MENU GAME AUDITS MENU ADJUSTMENTS MENU GAME UTILITIES MENU VOLUME MENU CALIBRATE STEERING AND THROTTLE >» START THE GAME

Press TEST to execute this command

MAIN OPERATOR MENU SCREEN

The Operator Menu is the top-level screen of the Menu System. It presents the general categories of operator selectable items. All subsequent screens show more detail than this one. This screen does not permit changes. This is the only menu that allows the operator to exit from the menu system by choosing Start the Game.

Unlock and open the door to use the operator control switches. Press the TEST button to enter the Operator Menu screen. Use the Volume Up and Volume Down buttons to move up or down through the list of items. Follow the on-screen instructions to continue to other menu screens.

The top center area of the screen between the game and manufacturer’s logos displays information about major variables that affect game operation. FREE PLAY ON indicates that the game will start without inserting currency or tokens). Network play off-line indicates that this game is not linked to another at this time. These items may be changed from the Adjustments menus.

Operation 2-6

Page 16

GAME AUDITS

MIDWAY

GAME STATISTICS AUDITS TOTALS AUDITS BY TRACK AUDITS BY BOAT » RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

GAME AUDITS MENU SCREEN

The Game Audits Menu provides the operator with options for various summaries of the game statistics and audits. Detailed reports give statistics based on player selections and performance.

To view a report, use the operator control switches to select the Game Audits Menu and a specific report. Press TEST to activate the report. Follow the on-screen instructions to continue to other menu screens.

Use the information in these reports to keep records of the game’s popularity and earnings. The operator may also analyze favorite tracks, most frequently used boats, and other statistics. These screens report information but do not permit changes.

Examine and record all game audit values before doing service or making repairs on this game.

NOTE: Use caution when clearing audit information. Once data has been cleared, it cannot be restored. Use the “Save Audits to Floppy Disk” option on the Game Utilities Menu to save the data for analysis. To clear these statistics or audits, go to the Game Utilities Menu.

Operation 2-7

Page 17

GAME STATISTICS

MIDWAY

GAME STATISTICS

POWER ON TIME

TIME IN A RACE

POWER ON TIME SINCE RESET

TIME IN A RACE SINCE RESET

LOST LINKS DURING A RACE

OUT OF SYNC GAMES

WATCH DOG RESETS

RELINKS

LEFT COIN COUNT

RIGHT COIN COUNT

THIRD COIN COUNT

FOURTH COIN COUNT

BILL COUNT HR,

HR,

HR,

HR,

Press TEST or CREDIT to return to previous menu

GAME STATISTICS SCREEN

The Game Statistics report displays general information about coin counts and game usage. Use the operator control switches to select Game Statistics from the Game Audits menu. Press TEST to enter MIN

MIN

MIN

MIN

the Game Statistics display. This screen reports information but does not permit changes.

The Coin Count and Bill Count items permit the operator to assess currency collection. The other items present information on game operation.

Reset, link, and sync statistics are measures of the game software’s ability to recover from conditions that adversely affect game play.

Operation 2-8

Page 18

AUDITS TOTALS

ZS mipway

AUDITS TOTALS

GAMES PLAYED

CONTINUES

FREE GAMES WON

STARTS

FREE GAMES ~

TIME EXPIRES

DID NOT FINISH

FINISHES

1 PLAYER RACES

Z PLAYER RACES

3 PLAYER RACES

4 PLAYER RACES

Press TEST or CREDIT to return to previous menu

AUDITS TOTALS SCREEN

The Audits Totals display additional information about player statistics and ability. This information assists the operator in understanding game usage and profitability. Use the operator control switches to select Audits Totals from the Game Audits menu. Press TEST to enter the Audits Totals display. This screen reports information but does not permit changes.

Free Games Won remains at zero if the bonus and award options are set to OFF. Refer to the General Adjustments Menu for the bonus and award options settings.

Two-, Three-, and Four Player Races remain at zero if no other games are linked to this one.

Operation 2-9

Page 19

AUDITS BY TRACK

ZED MIDWAY

PAGE 19) Fad SHTP GRAVEYARD

GAMES PLAYED

CONTINUES

FREE GAMES WON

STARTS

FREE GAMES ~

T

D

F

Zz

Press down; IME EXPIRES

ID NOT FINISH

INISHES

PLAYER RACES

PLAYER RACES

PLAYER RACES

PLAYER RACES

to page up; YOL+ to page CRED Fee REeUPA Lote Se bas menu

TYPICAL AUDITS BY TRACK SCREEN

The Audits by Track report gives operators more specific information about player choices and ability. Use the operator control switches to select Audits by Track from the Game Audits menu. Press TEST to enter either display. This screen reports information but does not permit changes.

There are several pages of these audits. The name of the track appears at the top of the page. Press the VOLUME UP or VOLUME DOWN buttons to move through these pages.

Operation 2-10

Page 20

AUDITS BY BOAT

miDway

PAGE 1 OF 13 BANSHEE

GAMES PLAYED

CONTINUES

FREE GAMES WON

STARTS

FREE GAMES ~

TIME EXPIRES

DID NOT FINISH

FINISHES

1 PLAYER RACES

2 PLAYER RACES

3 PLAYER RACES

4 PLAYER RACES

Press YOL- to page u YOL+ to page down; CREDIT to retu to previous menu

TYPICAL AUDITS BY BOAT SCREEN

The Audits by Boat report gives operators more specific information about player choices and ability. Use the operator control switches to select Audits by Boat from the Game Audits menu. Press TEST to enter either display. These screens report information but do not permit changes.

There are several pages of these audits. The name of the boat appears at the top of the page. Press the Volume Up or Volume Down buttons to move through these pages.

Operation 2-11

Page 21

DIAGNOSTICS

MIDWAY

SWITCH AND LAMP TEST

HARDDRIVE TEST

STEREO SOUND TEST

MONITOR PATTERNS MENU

FORCE FEEDBACK ADJUSTMENTS MENU

WATCHDOG RESET TEST

>» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

DIAGNOSTICS SUB MENU SCREEN

These tests allow the operator to verify the electrical and electronic condition of the game. This screen does not permit changes.

To select these tests, use operator control switches to select the DIAGNOSTICS MENU and press TEST to activate it. The screen displays the sub menu. Use the same steps to activate any one of the items listed. Follow the on-screen instructions to continue to other menu screens.

Operation 2-12

Page 22

SWITCH AND LAMP TEST

mIDway

Buttons

counts 1: Zz

Note: HOLT and YOL¢ contro, the wheel forge, feedback HIGH cycles lamps; LOW toggles all ta Press TEST 3 times to return to previous menu

SWITCH AND LAMP TEST SCREEN

Use the operator control switches to select the Switch and Lamp Test and press the TEST button. This screen reports information but does not permit changes.

Activate each switch and the indicator on the screen changes state. Release the switch and the indicator returns to its previous normally open or closed condition. Switches may be tested in any combination. These Switch Tests are used to verify crossed wires, intermittent conditions, and stuck switches.

The Buttons tests include the player control switches and operator control switches. Activating any of these switches causes the indicator on screen to change from OFF to ON and from gray to green. Each button change should be exactly duplicated by a single indication on the menu screen.

The Coin and Cabinet Switches are shown on the screen without regard for their actual game location. Each switch change should be exactly duplicated by a single indication on the menu screen.

The Lamps tests indicate the state of each of the lamps within control panel and overhead linking sign, or “header” (if installed). Press the LOW button to activate all of the lamps simultaneously, or the HIGH button to cycle the lamps in order. The HEADER TOP and HEADER BOT lamp tests have no effect unless a header or leader light is installed on the cabinet.

The Analog I/O test displays a value relative to the travel limits of the steering wheel or throttle indicating the current position of each control. Wheel position varies between 0 (full left) and 255 (full right). Throttle position varies between 0 (full back) and 255 (full forward).

The Coin Counts display the total number of coins deposited through each mechanism. Insert currency or tokens to perform these tests.

Operation 2-13

Page 23

HARD DRIVE TEST

> mipway

Checking for C: €: passed €hecking for Bz passed Press TEST to continue

HARD DRIVE TEST SCREEN

The Hard Drive Test verifies the functioning of the Hard Disk Drive Assembly.

Highlight the test by using the operator control switches to select the option; then press TEST to begin. This screen reports information but does not permit changes.

The Hard Drive Test verifies the existence of the data necessary for the game to operate. Each test should return a “passed” result. Other results may indicate a problem with the hard disk drive.

There is a single hard disk drive unit in this game. It is partitioned into two virtual drives, C: and D:. The test should report “passed” for both drives for the game to work properly.

Press TEST to exit the Hard Drive Test.

Operation 2-14

Page 24

STEREO SOUND TEST

MIDWAY

ady for sound test Bras’ f28r*fo"bestn Playing TOP, channe Press TEST to continue Playing SEAT channel EST to continue ress nd test completed ss TEST to end

STEREO SOUND TEST SCREEN

The Stereo Sound Test verifies the operation of the stereo sound hardware and cabinet speakers. Increase the master volume level before beginning this test. Use the operator control switches to select this test and press TEST to activate it. This screen reports information but does not permit changes.

Press the TEST button when prompted by on-screen instructions to check each speaker and the game sound hardware. Listen to the audio signals from the speakers listed on the screen. There should be little or no sound coming from other speakers during each test. Use these tests to find crossed connections, incorrect phase, rattles, vibration, distortion, etc.

Press the TEST button to exit the Stereo Sound Test.

Operation 2-15

Page 25

MONITOR PATTERNS TEST

‘ Chile) MIDWAY

MONITOR PATTERNS MENU

COLOR BARS CROSS HATCH RED BLUE GREEN WHITE BLACK 5@% GRAY 257% GRAY » RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

MONITOR PATTERNS SUB MENU SCREEN

NOTE: This game uses a medium resolution monitor. The increased resolution means that more video information is displayed on the screen than with standard resolution monitors. Use of an industrial-grade degaussing coil is recommended before any corrections to monitor adjustments are attempted.

The Monitor Patterns routine provides test screens to verify monitor performance or make adjustments. To begin the tests, use the operator control switches to choose Monitor Patterns Menu from the Diagnostics Menu screen and press TEST to activate the sub-menu. Select a test from the sub-menu and press TEST to activate it. Press TEST once again to return to the Monitor Patterns sub menu.

Color Bars fills the screen with shades of colors to verify red, green, blue and white level dynamic adjustments. Each color bar should appear sharp, clear, and distinct from bars on either side.

There are 31 levels of intensity displayed in each of the color bars. Incorrect adjustment can cause detail to be missing at the top or bottom of a color bar. Set the monitor controls so that the maximum number of levels is visible in every bar.

The Color Bars screen helps to adjust the monitor brightness and contrast.

Cross Hatch fills the screen with a grid and a series of dots. The grid and the dots should be completely white, with no fringes or parallel images. The lines should be straight and the dots round.

Consult the service literature from the manufacturer of the monitor for more detail on these adjustments.

The Crosshatch Patterns assist in verifying the monitor convergence, linearity, and dynamic focus.

Operation 2-16

Page 26

MONITOR PATTERNS TEST (continued from previous page)

Red, Blue, and Green Color Screen tests fill the screen with 100% of the chosen color at normal intensity. Each screen should be absolutely uniform from top to bottom and side to side. No retrace lines or noise should be visible.

The Color Screen tests can verify monitor intensity, black level, blanking and color purity.

Color Screens may not hold their uniformity if the monitor degaussing circuit is defective.

White, Black, 50% Gray, and 25% Gray Screens fill the screen with black, gray or white at various intensities. The screens should be uniform with no color tints or distortion. No retrace lines or noise should be visible.

If any of the tests shows a need for adjustment, use the proper controls on the Video Monitor.

Operation 2-17

Page 27

FORCE FEEDBACK ADJUSTMENTS,

CU) miDway

USE FORCE FEEDBACK ON FORCE FEEDBACK ADJUSTMENT FORCE FEEDBACK CENTER TEST » RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

FORCE FEEDBACK ADJUSTMENT MENU SCREEN

The Force Feedback Adjustment Menu allows operators to set the use and intensity of feedback from the steering wheel motor. Select the test or adjustment with the operator control switches and press TEST to activate it. This screen permits changes to the existing values.

The Force Feedback Adjustment ranges from 0% (minimum) to 100% (maximum) with 50% as the factory default setting. Use a higher amount of force for players with greater upper body strength. Younger players may be more comfortable with lower force settings.

The Force Feedback Center Test checks the functioning of the steering wheel motor drive circuits. Select this item and move the steering wheel to any position. The wheel must automatically return to its center position as soon as it is released. If it does not do this, the boat will not respond properly.

Operation 2-18

Page 28

WATCHDOG RESET

miDway

SWITCH AND LAMP TEST HARDDRIVE TEST STEREO SOUND TEST MONITOR PATTE FORCE FEEDBAC WATCHDOG RESE RETURN TO PRE

L—_and YOL+ to select; © accept; CREDIT to cancel

WATCHDOG RESET TEST CONFIRMATION BOX

The Watchdog Reset Test checks the function of the game’s watchdog circuit by causing a forced reset. Use the operator control switches to select the Watchdog Reset Test, then press TEST to activate it. This test is similar to the restart command available on many personal computers.

Note: Use caution when performing a Watchdog Reset Test. Although game information should not be affected, audit data could be changed. Once data has been changed, it cannot be restored. Use the “Save Audits to Floppy Disk” option on the Game Utilities Menu to save the data for analysis.

When the operator chooses the Watchdog Reset Test, a confirmation box appears superimposed on the screen (as shown above). Select YES to reset the game or NO to return to the Diagnostics Menu. Upon reset, the screen blanks and the game starts up again. Note and record any messages that occur during this startup sequence.

Operation 2-19

Page 29

ADJUSTMENTS MENU

mIDway

GENERAL ADJUSTMENTS MENU DIFFICULTY ADJUSTMENTS MENU NETWORK ADJUSTMENTS MENU SET TIME AND DATE >» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

ADJUSTMENTS MENU SCREEN

The Adjustments Menu allows operators to set game and player variables. Use these screens to optimize game performance and earnings.

The General Adjustments include pricing, game variables and cabinet type variables. Select these items to set player incentives, the cost of playing, and the size of game equipment.

The Difficulty Adjustments set the level of game difficulty. These adjustments can optimize the game’s characteristics to best suit the needs of players.

The Network Adjustments control variables related to linking. These items are required to establish the identity of all cabinets in a network. These adjustments are transparent to the players.

Operation 2-20

Page 30

GENERAL ADJUSTMENTS MENU

miDway

METRIC OFF FREE PLAY OFF FREE RACE FOR ist ON MIN MULTI-PLAYER FOR FREE RACE OFF ENABLE ALL BOATS UNLOCK ALL TRACKS RACES FOR BONUS 1 RACES FOR BONUS Z CABINET TYPE S1TDOWN PRICING MENU FORCE FEEDBACK ADJUSTMENT MENU SELECTION TIME ADJUSTMENTS MENU >» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

GENERAL ADJUSTMENTS MENU SCREEN

The General Adjustments Menu contains options to control the cost and type of play. It also sets the cabinet type game display and measurement system. Select a variable with the operator control switches. Use the VOLUME UP and VOLUME DOWN buttons to change a variable. Certain items have sub-menus. This screen permits changes to the existing values.

Metric sets the measurement system for display on game screens. Set this option to ON to display speed in kilometers per hour. Set this option to OFF to display speed in miles per hour. Factory default is OFF.

Free Play determines whether the game accepts currency or tokens for play, or allows operation without cost. Set this option to ON for free play. Set this option to OFF for paid play. Factory default is OFF.

Free Race for 1* permits a free game incentive for players who finish a race in first place. Set this option to ON to award a free race to a first-place finisher. Set this option to OFF to eliminate the free race award. Factory default is ON.

Min Multi-Player For Free Race sets the minimum number of players needed to activate the free race award for a first-place finish. The choices are OFF, two, three, or four players. Factory default is OFF. Use this feature to encourage players to participate in linked races.

Enable All Boats determines whether all boats are available for player selection at the start of a race. Set this option to OFF to hide certain boats from first time players. Set this option to ON to enable players to choose from all possible boats at all times. Players can override this option to choose from all boats by pressing any of the view buttons during the boat selection screen. Factory default is OFF.

Operation 2-21

Page 31

GENERAL ADJUSTMENTS MENU (continued)

Unlock All Tracks enables or disables certain tracks until players finish a certain number of races. The hidden tracks are revealed as “bonus” tracks. Set this option to OFF to hide the “bonus” tracks. Set this option to ON to enable players to choose from all tracks at all times. Factory default is OFF.

Races for Bonus 1 is available only when Unlock All Tracks is turned OFF. This adjustment sets the number of races a player must complete to unlock the first of the hidden tracks. The range of adjustment is from 1 to 8 races. Factory default is 3.

Races for Bonus 2 is also available only when Unlock All Tracks is turned OFF. This adjustment sets the number of races a player must complete to unlock the second of the hidden tracks. The range of adjustment is from 1 to 8 races. Factory default is 2.

Pricing Menu allows the operator to choose from several pre-determined currency combinations. Select this item and press TEST to change the cost of starting and continuing a game. This option is disabled if Free Play is ON. Factory default is USA1.

Force Feedback Adjustment Menu allows changes to the amount of feedback from the steering wheel. Refer to Force Feedback Adjustment description on a previous page.

Selection Time Adjustments Menu permits operators to set the amount of time for a player to make selections at the beginning or end of play. Longer than necessary times cut into the number of games that can be played in one day. Slower or first time players may not be able to read information and act with very short times. When this adjustment is chosen, another menu screen presents the following items:

Track Select Time and Boat Select Time set the limits for player decisions at the beginning of a race. The range of adjustment for each item is from 10 to 60 seconds. Factory defaults are 15 seconds.

High Score Time and Continue Time set the limits for player decisions at the conclusion of each race. The range of adjustment for each item is from 10 to 60 seconds. Factory default for High Score Time is 20 seconds. Factory default for Continue Time is 17 seconds.

Operation 2-22

Page 32

PRICING MENU

MIDWAY

SELECT CUSTOM PRICING SELECT STANDARD PRICING VIEW CURRENT PRICING RESET TO DEFAULTS >» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

PRICING MENU SCREEN

The Pricing Menu contains options for selecting standard and custom currency combinations. Use the operator control switches to select Pricing Menu from the General Adjustments Menu and press TEST.

Select Custom Pricing allows the operator to set coinage and credits options manually. Use this item to set up combinations not found in the standard listing. This screen permits changes to the existing values.

Select Standard Pricing allows the operator to select from several standard price schemes. The most commonly used currency requirements to start and to continue games are ready for operator selection. This screen permits changes to the existing values.

View Current Pricing displays the present currency and credit settings. Choose this item to review the active game price scheme. This screen reports information but does not permit changes. Use either of the Select Pricing options to make changes, then return to this screen to verify the settings.

Reset to Defaults returns the price settings to factory defaults. Choose this item to return all variables to their original values. This screen permits changes all of the existing values at one time.

Operation 2-23

Page 33

PRICING SUBMENUS

MIDWAY

CUSTOM PRICING

LEFT UNITS RIGHT UNITS CENTER UNITS EXTRA UNITS DBY UNITS

UNI INI TS PER CREDIT TS PER BONUS

MIN UNITS

CREDITS TO START CREDITS TO CONTINUE

COINS PER BILL

SHOW CREDIT FRACTIONS

LEFT COIN COUNT RIGHT COIN COUNT CENTER COIN COUNT EXTRA COIN COUNT DBY COIN COUNT

CURRENCY

>» RETURN TO PRE MENU

Press TEST to retu

TYPICAL CUSTOM PRICING MENU

GA miDway

NORTH AMERICA

SOUTH AMERICA

EUROPE AZH

EUROPE 12Z

asia

AUSTRALIA

>» RETURN TO PREVIOUS MENU

Press TEST to return to previ

STANDARD PRICING MAIN MENU

Operation 2-24

Page 34

PRICING SUBMENUS (continued)

miDway

>» usA

usa

usa

usa

usa

usa

usa

usa

usa

uSA 10

usA 11

USA 12

usA 13

usA ECA

RETURN TO PREVIOUS MENU z

z

o

Press TEST to execute this command

TYPICAL STANDARD PRICING SUB-MENU

MIDway

CURRENT PRICING: USA 1

LEFT UNITS RIGHT UNITS CENTER UNITS EXTRA UNITS DBY UNITS

UNITS PER CREDIT UNITS PER BONUS

MIN UNITS

CREDITS TO START CREDITS TO CONTI

MAX CREDITS

COINS PER BILL

SHOW CREDIT FRACTIONS

LEFT COIN COUNT RIGHT COIN COUNT CENTER COIN COUNT EXTRA COIN COUNT DBY COIN COUNT

CURRENCY NN © + Agee

NUE

oa Zz°N

Press TEST to retu

TYPICAL VIEW CURRENT PRICING DISPLAY

Operation 2-25

Page 35

DIFFICULTY ADJUSTMENTS

GA, miDway

SHIP GRAVEYARD405@
LOST ISLAND485e
VENICE CANALS405e
LAKE POWELL405e
ARCTIC CIRCLE405e
NILE ADVENTURE485e
NEW YORK DISASTER485e
GREEK ISLES485@
FAR EAST485e
THUNDER PARK485e
HYDRO SPEEDWAY405e

FREE RACE LIMITER ReGe? TRACKS 10 pe raULTS RESET Al TO DEFAULTS >» RETURN TO PREVIOUS MENU

Difficulties: 1 EASIEST, 1@@ = HARDEST Press TEST to return to previous menu

DIFFICULTY ADJUSTMENTS MENU SCREEN

The Difficulty Adjustments set how much skill players must have to complete a race. Use the operator control switches to select Difficulty Adjustments and press the TEST button to activate the sub menu. Select each variable using the operator control switches and press TEST to enter change mode. Use the operator control switches to change the variable, then press TEST to save changes and exit the variable.

Track Difficulty sets the initial time available for play. Higher values require players to maintain faster average speeds between checkpoints. The range of adjustment is from 1 to 100. Factory default is 40.

Al Difficulty sets the competitiveness of drone boats. The number of boats does not change, but their skill at negotiating the track does. The range of adjustment is from 1 to 100. Factory default is 50.

The Free Race Limiter enables the Al (Artificial Intelligence) to keep pace with players’ skill levels. Set this to ON to limit the number of free races based on player ability. Set it to OFF to keep Al values at a fixed level regardless of the number of free races won. The range is OFF or ON. Factory default is OFF.

Limit Free Races To is the award cut-off point. It prevents expert players from monopolizing a cabinet. It may be fixed or variable (see Free Race Limiter above). The range is 1 to 100%. Factory default is 20%.

Reset Tracks to Defaults returns the Track Difficulty settings to factory defaults. Choose this item to return this variable to its original value. This screen permits changes all of the existing values at one time.

Reset Al to Defaults returns the Track Difficulty settings to factory defaults. Choose this item to return this variable to its original value. This screen permits changes all of the existing values at one time.

Operation 2-26

Page 36

NETWORK ADJUSTMENTS

Hit) zeae MIDway

NETWORK ENABLED UNIT ID ¢1-4> >» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

NETWORK ADJUSTMENTS MENU SCREEN

The Network Adjustments Menu allows an operator to set the game cabinet network identity. Use the operator control switches to select the Network Adjustments Menu and press TEST to enter the submenu. Use the operator control switches to select one of the items and press TEST to permit change. Select a new value, then press TEST once again to save changes and return to the above screen.

The best way to set these variables is to set all cabinets to this adjustment menu at the same time.

Set Network Enabled to ON if the cabinet is linked to other games. This allows the game electronics to communicate with other cabinets. Choose OFF to disable linked game play. Factory Default is OFF.

Unit ID determines the address of the game. Each linked game must have a unique number to prevent network confusion. Sequence is not important, only that no two are the same. Factory Default is 1.

Operation 2-27

Page 37

SET THE TIME AND DATE

miDway

SET HOUR 11 pm

SET MINUTES 26

SET SECONDS 33

SET MONTH

SET DATE 22z

SET YEAR

>» RETURN TO PRE

11:26:33 pm, Fri, Jan 22, 1999

Press TEST to return to previous menu

TIME AND DATE MENU SCREEN

The Set Time and Date menu provides the current date and time for the game. This screen also allows operators to adjust the clock for changes in time zones and seasonal changes in time. Use the operator control switches to select Set Time and Date, then press TEST to activate the sub-menu. Use the operator control switches to select a variable and press TEST to make changes. Select a new value, then press TEST once again to save changes and return to the above screen.

Once set, the clock runs until the battery dies or the electrical circuits are disrupted by service or a major fault. The clock assists in providing accurate game statistics. It does not affect the game operation.

Operation 2-28

Page 38

GAME UTILITIES MENU

A

GAME UTILITIES MENU

CLEAR CREDITS RESET OPERATOR SETTINGS RESET HIGH SCORES AND SPLIT TIMES RESET AUDIT STATS FULL FACTORY RESTORE SAVE AUDITS TO FLOPPY DISK » RETURN TO PI 1OUS MENU

EZ MIDWAY

Press TEST to return to previous menu

GAME UTILITIES MENU SCREEN

The Game Utilities Menu permits operator changes to credits, player statistics, and game audits. It also allows the operator to restore game settings to factory defaults or save audit information for later use. A confirmation screen appears before changes become final. Use the operator control switches to select the Game Utilities Menu and press TEST to activate the sub-menu. Follow the on-screen instructions to select any item and activate it.

Clear Credits resets the existing number of game credits to zero.

Reset Operator Settings returns the Adjustments Menus variables to the original factory defaults.

Reset High Scores and Split Times resets the player high score table to factory default ghost data.

Reset Audit Stats resets the track and boat audit values to zero.

Full Factory Restore resets all of the game variables above to factory default values at one time.

Save Audits to Floppy Disk allows the operator to save game data to a formatted 1.44MB high-density diskette before clearing values. The floppy disk drive is in the CPU cabinet. Comparison of audit data over time can provide the operator with useful information about the effect of game variables on profits.

Note: Once data has been cleared, it cannot be restored. Use the “Save Audits to Floppy Disk” option on this menu to save the data for analysis. Use caution when clearing audit information. To clear these registers, use the Reset or Full Factory Restore functions of this menu.

Operation 2-29

Page 39

CALIBRATE STEERING AND THROTTLE

MIDWAY

CALIBRATE STEERING AND THROTTLE

CENTER THE WHEEL SET THROTTLE TO NEUTRAL THEN PRESS TEST OR BOOST

WHEEL 6.50 Se |

THROTTLE 8.50 es

Press CREDIT to cancel

STEERING AND THROTTLE CALIBRATION INSTRUCTION SCREEN

MIDWAY

CALIBRATE STEERING AND THROTTLE

MOVE THE WHEEL THROUGH 17S FULL RANG Ee THE THROTTLE THROUGH ITS FULL RANGE THEN PRESS TEST OR BOOST TO ACCEPT

WHEEL 8.50 a Se |

THROTTLE 8.50 Ss |

Press TEST to accept; CREDIT to cancel

STEERING AND THROTTLE CALIBRATION ACTION SCREEN

Operation 2-30

Page 40

CALIBRATE STEERING AND THROTTLE (cont’d) Calibrate Steering and Throttle allows the operator to set the steering and throttle mechanisms for optimum control during game play. Poorly calibrated player controls can reduce profits. Calibrate the player control switches after making repairs to the game or moving it to a new location. Use the player control switches to select Calibrate Steering and Throttle and press the TEST button to activate the test.

Each of the controls has a minimum analog value of 0 and a maximum of 1.0 for its full range of motion. These numbers correspond to digital values from 0 to 255. Both sets of numbers must track correctly to achieve accurate steering of boats. When properly adjusted, the digital value will be equal to the analog value multiplied by 255. For example, a steering value of 0.5 (straight ahead) translates to a digital value of 128, exactly half way in between left and right steering wheel limits.

Operation 2-31

Page 41

VOLUME MENU

MIDWAY

MASTER VOLUME SEAT RUMBLE ATTRACT MUSIC ATTRACT YOLUME » RETURN TO PREVIC MENU

Press TEST to return to previous menu

VOLUME ADJUSTMENT MENU SCREEN

The Volume Menu allows the operator to adjust the relative loudness levels. Use the operator control switches to select Volume Menu, then press TEST to activate the sub-menu. Select an option with the operator control switches and press TEST to activate it. Follow the on-screen instructions to save the changes and continue to other menu screens.

Note: Use these adjustments to raise the audio levels during the sound tests. They may be returned to their optimum loudness after testing is completed.

Master Volume sets the relative volume level during game play. This value affects all of the other settings at the same time. The range is 1 to 100%. Factory default is 41%.

Note: The following individual volume adjustments are all affected by the Master Volume setting. However, this does allow the Attract sounds to be made higher or lower than the normal level of game sounds coming from the two upper cabinet speakers.

Attract Music selects sound or silence during the attract mode. This adjustment does not change any of the volume settings. Factory default is ON.

Attract Volume adjusts the sounds of the Attract mode only when Attract Music is set to ON. These sounds are independent of the game audio levels. The range is 1 to 100%. Factory default is 50%.

Operation 2-32

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43
NAMESTARTCONTINUE | CREDITS/COINCOIN 4COIN 2COIN 3COIN4BILL
NORWAY.221/2X1NKr, 3/5X1NKrANKrANKr
DENMARK321/2X1DkKr, 3/5DKr, 7/2X5DKrDkr5DKr
ANTILLIES221/25¢, 4/1G25¢1G
HUNGARY221/2X10Ft, 3/2X20Ft10Ft20Ft

Operation 2-34

Page 44

HYDROTHUNDER-

CHAPTER

THREE

SERVICE

NOTICE: The term VGM refers to the video game machine.

& CAUTION: This VGM uses complex electronic components that are very sensitive to static electricity. Observe the following precautions before handling VGM electronics. \Y Failure to do so may void your warranty and could damage electronic assemblies.

Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge. Before touching or handling electronic assemblies, discharge static electricity on your body. To discharge this static, begin by touching the case of the Arcade Computer. Next, connect the line cord to a grounded outlet. Don’t turn on the VGM! Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport VGM circuit boards. Transport the hard drive in its shipping container. Don’t remove or connect electronic assemblies when cabinet power is on. Otherwise, you'll damage electronic assemblies and void the VGM warranty. After you complete maintenance or service, replace ground wires, shields, safety covers, etc. Install and tighten ground and mounting screws.

Service 3-1

Page 45

SERVICING

Only qualified service personnel should repair VGM equipment. The following product guidelines apply to all video game operators and service personnel. Notes, cautions and warnings appear throughout this manual where they apply. Study the Safety pages before beginning service.

e Battery

across the terminals or from terminals to ground. These batteries are designed for ( CAUTION: If you install the battery incorrectly, it may explode! Avoid direct shorts very long life. Don’t attempt to recharge these batteries!

size, voltage rating, and composition. Manufacturer recommended equivalent types are acceptable. Store batteries in a safe place until you’ve completed repairs. Dispose of used batteries according to manufacturer instructions.

f CAUTION: Avoid an explosion! Replacement batteries must match the originals in

A battery on the CPU Board retains data in memory during power disruptions. This battery is a 3-volt, lithium button cell of type CR 2032. Switch off power to the game. Unlock and remove the rear door. Remove the back of the Arcade Computer. The battery resides toward the edge of the motherboard, near the daughter board sockets. Carefully pry up the battery retaining lever. Then grasp the battery edges and remove the device. Set the battery aside.

Note the “+” marking on one side of the replacement battery. When you install a battery, this “+” marking must face the battery retaining lever. After replacing the battery, set the system clock to the correct date and time. Also enter the Menu System and check or update system adjustments as necessary.

¢ Coin Counter Switch off power to the VGM. Unlock the cash door and swing it open. Find the meter at the lower left corner of the vault opening. Record the meter count before testing or replacement. Locate the meter wires. Disconnect wiring at the connector. Remove two screws from the front bracket. The meter is a 5V D.C. meter. Assure that the replacement meter has a diode across the terminals to protect driver circuits.

¢ Coin Mechanism Switch off power to the VGM. Unlock the coin door and swing it open. To clean or replace a coin mechanism, unlatch and remove it. After reinstallation, assure that the mechanism seats fully in its bracket. Close and lock the release latch. Then close the door. Enter the Menu System to change the coin mechanism setup. Test known good and bad coins to verify operation. e CPU Board

bas NOTICE: Avoid damage to electronics! Turn off VGM power before servicing circuit Ey boards or any electronic assembly. Never “hot plug” circuit boards.

The CPU Board is part of the Arcade Computer. Switch off power to the VGM. Open and remove the rear door. The Arcade Computer is behind this door. To expose the CPU Board, loosen four metal thumbscrews. Don’t remove the screws. These screws reside at the top and bottom corners of the case. Slide off the back of the computer. Disconnect the floppy disk power and data cables at the disk drive. Loosen the drive mounting screws. Lift the floppy drive out of the cabinet. Set it aside for reassembly. Remove the I/O Board brackets.

Service 3-2

Page 46

NOT REMOVE RELEASE

Remove the CPU Board power cables at the CPU Board. Remove the circuit board retention bars. Disconnect the Reset cable from the Filter Board and Motherboard, noting the orientation of the connectors. Remove the Filter Board Assembly, Video Card, and Network Card. Remove the floppy drive mounting bracket. Remove CPU Board mounting screws. Pinch the top of a CPU Board standoff and raise the board off the standoff. Repeat this procedure at the other standoffs. Lift the circuit board out of the cabinet and set it aside for reassembly. Use anti-static packaging from new parts to store boards that you won’t reinstall.

Dashboard and Steering Mechanism

Switch off power to the VGM. Remove the control panel bolts on the right and left side of the cabinet. Open the coin door and release the latches on the left and right sides of the control panel. Support the steering wheel and lower the dash. Be sure that you don’t pinch cables in the hinge.

Service 3-3

Page 47

20-9275-2 LINK SAFETY CH&IN

20-9347 SGLE. LATCH

Dashboard Assembly

—POTENTIOMETER

TEERIN

_7— TENSION BRACKET

D BELT

MOTOR BR

TENSION ADJUST BOLT—

Steering Wheel Assembly

Inspect the motor, pulleys, and belt. If the belt is broken or shows signs of wear, replace it. Locate the two nuts on each side of the motor mounting bracket. Loosen all four bracket nuts. Rotate the tension adjustment bolt as necessary. Tighten this bolt until the belt is taut. Then restore correct tension by loosening the bolt one full turn. Tighten the motor bracket nuts.

Wheel Driver Board Switch off power to the VGM. Unlock and open the coin door and rear door. Note the orientation of the connector and other cables. Extract the harnesses from the board connectors. Remove mounting screws and washers from the Wheel Driver Board. Lift the board off its mounting posts. Handle the board by a heatsink. If you aren't reinstalling the board, store it in an anti-static bag and protective container.

Service 3-4

Page 48

Dollar Bill Validator (Use MARS AE2451-U5 UL Recognized currency changer) Dollar bill validators or other currency acceptors may be installed in VGMs that were manufactured with the additional wiring connector. Switch off power to the VGM and unplug the AC line cord. Unlock the coin door and swing it open. Read the coin door label for additional information. Remove nuts, spacers, and cover plate from the door. Change switch settings or make adjustments before mounting the unit. If the manufacturer has supplied an adapter plate, place it over the door cutout. Install spacers on threaded studs. Align the validator mounting holes with the studs. Seat the unit in the door opening. Install and tighten the nuts. Attach the ground wire (green with yellow stripe) lug to the door ground stud. The stud is beside the hinge. Mate the wiring harnesses and press them together to fully seat connectors. Route wires away from door edges and hinge. Inspect the bill chute for proper alignment. Set the dollar bill validator to produce long output pulse widths, 1 pulse per dollar, and accept dollar bills only. To remove for service or replacement, reverse these steps. Plug in the line cord and turn on the VGM. From the Menu System, change the mechanism setup and pricing. Then test known good and bad bills to verify proper operation. Close and lock the coin door.

Fans Switch off power to the VGM. Remove the cabinet rear door. Remove the back of the Arcade Computer. To remove a fan, disconnect its power harness and remove the fan mounting screws.

Note the fan orientation. Each fan has an arrow molded into its plastic case to indicate airflow direction. Be certain to reinstall the fans in the proper direction to assure airflow over circuitry.

Throttle Lever Switch off power to the VGM. Unlock and open the coin door. Unlatch and lower the dashboard. Remove three tamper-resistant bolts at the base of the lever. Lift off the throttle lever. Careful! Cable remains attached to the lever. To remove throttle assembly, unbolt the assembly cover. Support the assembly, then unbolt it from inside the control panel.

Hard Disk Drive Switch off power to the game. Unlock and remove the rear door. Remove the back of the Arcade Computer. Disconnect the DC power cable from the hard disk drive. Unplug the ribbon cable from the hard drive but leave it attached to the CPU board. Remove the drive mounting screws. Lift the drive out of the cabinet. Save the mounting screws for reuse in future hard drive installations. When returning a hard drive to your distributor, pack it in an anti-static bag. Box the drive in approved shipping container 08-8068.

CAUTION: Hard disk drives are very fragile! Handle them with care. Keep disk drives away from magnets, heat and vibration. Don’t move a game with the power on.
CAUTION: Don’t stack or drop hard disk drives. Use an anti-static bag and an approved shipping container to return the drive to your distributor.

REINSTALLATION. Before mounting the hard drive in its bracket, install the drive mounting screws. To avoid damage during installation, mount the hard drive in the brackets before connecting cables. After a driver plays one game, the new drive copies data from other linked VGMs. Important! The data won't copy if players are actively driving. Files transfer only when all VGMs return to Attract Mode.

Audio Amplifier Board Switch off power to the VGM. Unlock and open the rear door and the coin door. Note the orientation of the connector and other cables. Extract the harnesses from the board connectors. Remove mounting screws and washers from the Audio Board. Lift the board off its mounting posts. Handle the board by a heatsink. If you aren't reinstalling the board, store it in an anti-static bag and protective container.

Service 3-5

Page 49

Diego Interface Board

Switch off power to the VGM. Unlock and open the rear door. Extract the harnesses from the board connectors. Remove mounting screws and washers from the Diego Board. Remove the Diego Board. Lift the board off its mounting posts. During reinstallation, tighten the screws: Start at the board’s center and work toward the outer edge. If you aren’t reinstalling the board, store it in an anti-static bag and protective container.

Speakers Switch off power to the VGM. Unbolt and remove the speaker grille from below the marquee. Note the orientation of speaker wires. Unbolt and remove the speakers. To remove subwoofer, unlock and open the rear door. Note the orientation of speaker wires. Unbolt and remove the speaker.

Marquee Light Box

Switch off power to the VGM. Remove the speaker panel screws. Lift off the marquee glass and artwork to expose the interior of the light box.

Viewing Glass

Switch off power to the game. Unlock and open the coin door. Unlatch and lower the dashboard. Remove the glass retaining bracket at the bottom center of the viewing glass. Carefully remove glass and set aside. Clean glass before reinstalling. Monitor

WARNING: The video monitor is very heavy, with most of the weight toward the front. Solidly support the monitor as you remove from it from the cabinet.
WARNING: When operating the monitor outside the cabinet, use an isolation transformer. In normal operation, the monitor doesn’t require isolation from AC line voltage.

Switch off power to the VGM. Unlock and open the coin door. Unlatch and lower the dashboard. Remove the viewing glass. Lift out the monitor bezel. Remove the flange nuts that secure the monitor's mounting brackets to its mounting panel. Carefully pull the monitor from the cabinet. Set the monitor in a safe place. Clean the face of the CRT and viewing glass before reinstalling the bezel and viewing glass.

Network Interface Board Switch off power to the VGM. Unlock and open the rear door. Remove the back of the Arcade Computer. Note the orientation of the cables. Loosen the header-mounting screw. Disconnect the network cables from the board header connectors. Remove the circuit board retention bars. Remove the board. If you aren't reinstalling the board, store it in an anti-static bag and protective container.

Video Card Switch off power to the VGM. Unlock and open the rear door. Remove the back of the Arcade Computer. Loosen the header-mounting screw. Disconnect the video cable from the board header connector. Remove the circuit board retention bars. Remove the board. If you aren’t reinstalling the board, store it in an anti-static bag and protective container.

Filter Board Switch off power to the VGM. Unlock and open the rear door. Remove the back of the Arcade Computer. Note the orientation of the cables. Loosen the header-mounting screw. Disconnect the cables from the board header connectors. Remove the board. If you aren't reinstalling the board, store it in an anti-static bag and protective container.

Service 3-6

Page 50

DIMMs (Dual In-line Memory Modules)

destroy sensitive circuits. Before touching or handling electronics, discharge static

ry CAUTION: Static electricity builds up on your body. This static can damage or

WK electricity by touching the power supply chassis.

DIMM circuits contain the computer read-write memory for this game. Switch off power to the game. Remove the cabinet rear door. Remove the back of the Arcade Computer. Unplug the ribbon cable from the floppy drive. Leave the other end of the cable attached to the CPU Board. Unscrew and remove the circuit board retention bars. Remove the floppy drive mounting bracket. Remove the floppy drive. Note DIMM positions. Press out on the locking retainer on each side of the DIMM. The DIMM should partially or completely pop out of its socket. Lift the DIMM from its socket. Handle the DIMM only by its edges.

DIMM Installation

To reinstall memory circuits, hold the DIMM upright over its socket. Make sure the keying holes and notches are in their proper positions. Gently push the DIMM board into the socket, so that the board snaps into place under the locking retainer on each side of the socket. Be sure that the retainers mate tightly with DIMM board notches. Do not force a DIMM into its socket!

Service 3-7

Page 51

ARCADE COMPUTER MECHANICAL COMPONENTS

FLOPPY DRIVE

» DRE INTING. BRACKET

8 vouT Ema” BATTERY

computer__/ ORE

LING. FAN ASSEMBLY

/ Fait GRILLE —

Service 3-8

Page 52

HYDROTHUNDER |

CHAPTER

FOUR

PARTS

WARNING: USE OF NON-MIDWAY PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR EQUIPMENT DAMAGE! USE ONLY MIDWAY AUTHORIZED PARTS. For safety and reliability, substitute parts and modifications are not recommended. Substitute parts or modifications may void EMC directives or FCC type acceptance.

Parts 41

Page 53

Parts _ 24-8809 7 FLUORESCENT BULB. NUT, 8 \_ 5555-15098-00

8 OHM SPEAKER

52 KEPS. \__01-10819

OR MTG. BRKETS

\_ 4420-01141-00 Nur

FLANCE GRIP

CABINET FRONT VIEW

Page 54

31-3440 __ SCREENED M4

01-13562.1__ SPEAKER GRILL 16 PIN-HD-AB MARQUEE ASSEMBLY

4108-01219-11 SPECIAL”

JEE

Parts 4-3 __03-8252-2 ARQUEE RETAINER

ON ' \_08-7456-17 MARQUEE

K__03-9373-1 1 ¢ EL 3S EDGE

Page 55

CABINET REAR VIEW

OMPUTER (SEE DETAIL I

ET AC PLUG EMELY (SEE APE

\ STER WHEEL EMPLY SEE DETAIL DRAWING)

Parts 4-4

Page 56

Parts 4-5 N rT 4420. /4—20 Fl 4108-01219-11 MS #8x11/ 6 PHN

-01141-00__

LANCE GI

01-11291_

BRACKET

03-7602_,

VENT HOLE VER

____01-8989

JPPER

01-7264 { LOCK RETA\

INER PI

____ 4420-01141-00 t = BOLT 1

LATE

20 FL __01-11285 LOCK PLATE

  • 10850 BOLT

/4—20x1-1/ ___ 4320-01 123-20B /4=20x1 = REAR DOOR ASSEMBLY

Page 57

COIN DOOR ASSEMBLY

(See coin door application chart for assembly and part numbers)

COIN ENTRY PLATE

ENTRY / REJECT. BUTTON

LIGHT BULB

SOCKET —

= REJECT FLAP

UPPER PLATE

Lower PLATE

  • HEX NUT

Parts 46

Page 58

COIN DOOR ASSEMBLY cont’d

(See coin door application chart for assembly and part numbers)

\_A-21069 NN COIN METER S|

Parts 47

Page 59

DASH ASSEMBLY

A-23303

20-10209-2 /~ PUSHBUTTONGWHITE) _-4020-01178-08, /4=20 » 1/2 Fl | 20-10209-1 PUSHLUTTON(RED) Lk

/—4420-01141-00 (rer 9/4220 FLANGE

o4-12773 A.23100 te DESH BRACKET 03-9945 he OVERLAY CONTROL PANEL

_01-15053 THROTTLE LEVEN

\_04-12646 THROTTLE. co

2 owt

THEOTLE

3 34 o1-15102 THROTILE-DECAL PLATE

02-5351.1_/ Hue

20-10189

STEERING MECHANISM

20-10134

POTENTIOMETER — 5014-12909-00 KEY ARE

_— HUB 02-5361 Lochyacner

20-10189

NUT 4427-01183-00 DRIVE MOTOR 14-8039

TOOTHED BELT —— 20-10186

Parts 48

Page 60

Parts 4-9 ___ 04-12643.1 THROTTLE HUB 20-10517 SHAFT 1/8 SQ.x7/8 KEY

POT/BRACKET AS 20-8712-18 04-1295 SHAFT \ /~ CAN

4006-01076-04__ SET § 6-52 02-5352 /— CAM PIN

03-9778 02-5340__ N PAD

SHAFT—2 THROTTLE MECH FLAT WASHER .68x.50x.06

04-11297, 02-5338 THROTTLE. MECH — s R 02-5339 FERRULE — ___ 4700-00021-00 {FLAT WASHER .20.5x.437x.052

03-9774 CAM FOLLOWER 4010-01070-08 0-32x1/2 HH

4700-00021-00 FLAT WASHER .203x.437x.032 = 01-14897 T ARM

4010-01070-10 iS ds: 8 HH

MW THROTTLE ASSEMBLY A-23327

Page 61

THROTTLE LEVER ASSEMBLY A-23100

1svo Ha~C-Hd “MAATT FVULLOMHL 97921-v0 —— 01-S0010-900h —— S1dyvO FWLOMHL bySOl-02

  • ZI-8hLL0-0l0r 11 XL HA /EXeS—C

—— }v€S-20 SadOHa IWLdd YaOVdS

  • d109) 1 HO SuOLyI L2v0l-02 ang LANSTTAl

LHOM oses-rz ——

LN H

  • v6v01-02

Parts

Page 62

ARCADE COMPUTER ASSEMBLY

04.12574.2

20-10561 VIDEO CARD ——\ Bien SUPPLY 20-40860 \ ASSEMBLY NETWORK INTERFACE CARD

5795-15344-12 —— HARD DISK DRIVE RIBBON

\-23224 HARD DISK DRIVE ASSEM

04-12687 COMPUTER CASE

Parts 4-11

Page 63

ARCADE COMPUTER MOTHERBOARD AND PERIPHERAL CARDS

20-10554 MOTHER BOSRD— INTEL SE440Bx-2 °

04-12687 COMPUTER 04-12651 CASET FILTER BOARD ‘ ASSEMBLY

\_ 20-10551 VIDEO CARD

\\ 20-10550 NETWORK INTERFACE BOARD,

Parts 412

Page 64

ARCADE COMPUTER MECHANICAL COMPONENTS

POHEAD SCREW vi/LOCK WASHER 5o32, 1/8

20-1068. FLOPPY DRE

12885 FLOPPY DRWE MOUNTING. BRACKET

9412861 CARD RETENTION Ess — N/THRESDED SURE

~_ sres-tss4a-12

HERD Disk PeNe FIBECN CABLE 49 PIN STRAIGHT

\_Luwr steuporr 1/a7 3/8" HEIGHT

94-1280. HEED DISK DRIVE MOUNT BRACKET

\_agaeay FLED DISK DRIVE ASSEMBLY t Ss

& _ 219560, Fall CME \__ecsevr tupeine sorew Hoe

Parts 413

Page 65

ARCADE COMPUTER MOTHERBOARD AND CPU

20-10554 MOTHERT INTEL SE

HEAT SINK 5882-16135-00 . saan CRRA LITHIUM BATTERY SDRA\ ae va

20-10549 CPU FAN MBLY

NOTE 1: Although This Motherboard Is A Stock Item Used On Many Personal Computers, It Requires A Custom Operating System To Function In This Game.
NOTE 2: DIMM and CPU modules from other manufacturers may be electrically equivalent or better than those illustrated here, but performance has not been verified with alternate components. Check with your distributor for information before attempting to use other than factory authorized parts.
NOTE 3: Celeron and Slot 1 are registered trademarks of Intel.

Parts 414

Page 66

COMPUTER MOTHERBOARD ASSEMBLY

20-10554

J7M1

Jah o+ DO -_, st hk ig {

DESIGNATION B FAN J8A1 Field Replaceable Parts

PART NUMBER 5882-16135-00 20-10549 5882-13046-00 20-10553 20-10557 FUNCTION Memory Backup Processor Cooling Shunt Jumper Processor Assembly Dual Inline Memory Module

Parts 415 DESCRIPTION 3Volt Lithium Battery Fan with Bracket Startup Configuration Celeron 333 Processor 64MB SDRAM DIMM

Page 67

NETWORK INTERFACE CARD ASSEMBLY

20-10550

Field Replaceable Parts

DESIGNATION PART NUMBER FUNCTION DESCRIPTION U2 - Instruction ROM Not required in this game

Parts 4-16

Page 68

VIDEO GRAPHICS CARD ASSEMBLY

20-10551

g

qq we

i

Field Replaceable Parts

DESIGNATIONPART NUMBERFUNCTIONDESCRIPTION
J6-Graphics Mode SelectNot required in this game

FILTER CARD ASSEMBLY

04-12651

OUTSIDE ~Pincine ERE

FZ Li U2 —_— 5 P4 i FS. Pa Fa P2 = U5

Field Replaceable Parts

DESIGNATIONPART NUMBERFUNCTIONDESCRIPTION
F1-F55060-15633-00EMI Filter2200 pF Dual Capacitor
L1-L55556-14181-00EMI FilterFerrite Bead Inductor

Parts 417

Page 69

AUDIO AMPLIFIER BOARD ASSEMBLY

04-12529.1

U4] if P2

PI

Field Replaceable Parts

DESIGNATION PART NUMBER FUNCTION

U1-U25370-15163-00Audio Amplifier
U35370-15984-00Audio Output
U45370-15833-00Audio Output
U55250-13302-00Voltage Regulator
U6-None

Parts 418 DESCRIPTION LM3403 Quad Amplifier TDA1560Q Power Amplifier TDA7375 Power Amplifier +5VDC 5% Fixed Regulator Not required in this game

Page 70

DIEGO INTERFACE BOARD ASSEMBLY

04-12522.4

JPIS P14 . JP

JP1

= ul4d

P12

JUPAS

x JZ x JP IPT Pl

Field Replaceable Parts

DESIGNATIONPART NUMBERFUNCTIONDESCRIPTION
L375551-16093-00EMI Filter47uH Inductor
Qi5190-15997-00Transistor2N2369 NPN
Q25370-12602-00Driver CircuitULN2064B IC
Q3-Q45160-14035-00Transistor2N3904 NPN
u115370-16103-00Voltage RegulatorLM34801-3.3

Parts 419

Page 71

WHEEL DRIVER BOARD ASSEMBLY

04-11127

Pt

Pa

DESIGNATION BRI D2-D3 D7 F1-F2 Qi Field Replaceable Parts

PART NUMBER 5100-13945-00 5070-14526-00 5070-15115-00 5731-14094-00 5162-08976-00 5160-14035-00 5370-12602-00 5370-14069-00

Parts FUNCTION Bridge Rectifier Diode Rectifier Dual Rectifier Circuit Protection Transistor Transistor Driver Circuit Power Driver

4-20 DESCRIPTION 100V 6A SIP MR751 100V 6A MUR1605 50V 8A SIP 4A 125V 5x20mm SB Fuse 2N6427 NPN 2N3904 NPN ULN2064B IC LM12 Op Amplifier

Page 72

ELECTRONIC CABLE ASSEMBLIES

SERIAL COMMUNICATIONS CABLE (NULL MODEM DB-9F TO DB-9F)

20-10532

VIDEO COMMUNICATIONS CABLE (SHIELDED DB-15 TO DB-15)

5797-13171-00

Parts 4-21

Page 73

ELECTRONIC CABLE ASSEMBLIES

ft

(LEFT)

AUDIO AMPLIFIER CABLE (MINIATURE STEREO PHONE PLUG TO PHONO PLUGS)

04-12578-2

COMPUTER RESET CABLE (2-PIN PLUG TO LOCKING 2-PIN PLUG)

04-12657

Parts 4-22

Page 74

LINE CORD APPLICATION CHART

Part Number 5850- 5850- 5850- 5850- 5850- 5850- 5850- 13271- 13272- 13273- 13275- 13276- 13277- 13278- 00 00 00 00 00 00 00

Country USA Lal UK 7 Italy Ls Japan Ty New Zealand Lal Germany Spain Denmark Finland Holland Norway Switzerland : Hungary Canada Lal Austria France : Australia 7 Belgium Ld Saudi Arabia India 7

Indonesia Lal

[gus

TYPICAL LINE CORD

Parts 4-23

Page 75

COIN DOOR APPLICATION CHART

ELECTRO-MECHANICAL COIN DOOR ASSEMBLIES

Part Number 02 | 03 | 06 | 07 | 09 | 11] 13 | 14) 15 | 17 | 18 | 20 | 22 | 23 | 24 | 33 | 38 | 86 | 87 09-50000-

Country USA

UK 7

France 7

Ttaly 7 Japan 7 New Zealand 7

Germany 7 Spain 7

Denmark 7 Holland 7

Finland 7

Norway 7

‘Switzerland 7

Hungary 7

Austria 7

Australia 7

Belgium 7 Saudi Arabia

TRANSFORMER APPLICATION CHART

POWER TRANSFORMER ASSEMBLIES Part Number

5610-14927-00 5610-14926-01 5610-15275-00

Line Power 120 VAC 60 HZ LJ 230 VAC 50HZ Ld 100 VAC 50HZ 7

TYPICAL POWER TRANSFORMER ASSEMBLY

Parts 4-24

Page 76

HYDROTHUNDER™

CHAPTER

FIVE

WIRING & CIRCUIT INFORMATION

WARNING: Failure to reconnect all ground wires or to replace metal shields and covers with each mounting screw installed and securely tightened may result in radio frequency interference. Do not disconnect or connect cables, wiring harness, circuit boards, computer circuit cards, jumpers, etc., with the power ON. Doing so can damage game electronic components and void your warranty.

Wiring 5-1

Page 77

CABINET WIRING DIAGRAM

Revision] 8-0

ESL52 nbiwpl

sway 620 aad JALSnad HOI sisi

Wiring 5-2

Page 78

MAWWYOASNFYL SISSVHO Ua

AISWASSY

a [>] POWER WIRING DIAGRAM

wants aN

advo SN ADVLIOA = ATAWASST

Wiring 5-3

Page 79

COMPUTER MOTHERBOARD ASSEMBLY

20-10554

JBL «+ y ITM

° PEER EE st Sh ig {

ant

MOTHERBOARD CONNECTOR AND JUMPER STATUS

(NOTES FOR CHART ON FOLLOWING PAGE)

NOTES: . Jumper is not required for this game. No telephone connection necessary for operation. Jumper is not required for this game. A proprietary network is used for game linking. Connections not required for this game. No ATAPI devices (CD ROM) are used in this game. Jumper is not required for this game. The tamper detection security feature is not installed. Connect processor module fan to this jack. Computer may become unreliable if processor overheats. Connect processor module to this jack. The 242-pin socket accepts single microprocessor modules. Connections not required for this game. The case cooling fans connect directly to the power supply. Connections not required for this game. No SCSI device (Hard Disk Drive) are used in this game. Connect the reset cable from the Filter Card Assembly to this jack. No front panel devices are used.

  • Jumper must be set over pins 1 & 2 for this game. Game will not run if jumper is incorrect or missing. SL PNOTARWONYS
  • Replacement Motherboards may not include this jumper. Refer to Parts to order extra shunt jumpers.

Wiring 5-4

Page 80

MOTHERBOARD CONNECTOR AND JUMPER STATUS CHART

DESIGNATION LOCATION FUNCTION MEANING SETTING DEFAULT

J1A1

(NOTE 1) LOWER RIGHT NEAR BOARD EXPANSION SLOT NOT USED IN THIS GAME (NO TELEPHONE) OPEN 1&2

J1E1

(NOTE 2) LOWER CENTER NEAR BOARD EXPANSION SLOT NOT USED IN THIS GAME (NO PC LAN) OPEN

J1F2

(NOTE 3) LOWER CENTER NEAR BOARD EXPANSION SLOT CD AUDIO INPUT CIRCUIT NOT USED IN THIS GAME (NO CD PLAYER) OPEN

J2F1

(NOTE 3) LOWER CENTER NEAR BOARD EXPANSION SLOT CD DATA INPUT CIRCUIT NOT USED IN THIS GAME (NO CD PLAYER) OPEN

J2F2

(NOTE 1) LOWER CENTER NEAR BOARD EXPANSION SLOT TELEPHONY INPUT CIRCUIT NOT USED IN THIS GAME (NO TELEPHONE) OPEN

J2F3

(NOTE 3) LOWER CENTER NEAR BOARD EXPANSION SLOT AUXILLIARY INPUT CIRCUIT NOT USED IN THIS GAME (NO AUX DEVICES) OPEN

J3F1

(NOTE 4) MIDDLE CENTER NEAR CPU AND FAN CHASSIS INTRUSION CIRCUIT NOT USED IN THIS GAME (NO INTRUSION) OPEN 1&2

J3F2

(NOTE 5) MIDDLE CENTER NEAR CPU AND FAN PROCESSOR FAN CIRCUIT TWO SPEED FAN FOR PROCESSOR COOLING OPEN 1,2,&3

J4J51

(NOTE 6) CENTER LEFT MODULE WITH FAN ASSEMBLY SYSTEM MICRO- PROCESSOR SYSTEM MICRO- PROCESSOR OPEN FILLED.

J4M1

(NOTE 7) CENTER LEFT NEAR CPU MODULE PROCESSOR FAN CIRCUIT CONTROLLED FAN FOR PROCESSOR COOLING OPEN 1,2,&3

J7M1

(NOTE 7) UPPER LEFT NEAR POWER & FLOPPY JACKS CASE FAN CIRCUIT CONTROLLED FAN FOR HARD DISK DRIVE COOLING OPEN 1,2,&3

J8J1

(NOTE 8) UPPER LEFT BETWEEN HARD & FLOPPY JACKS SCSI DRIVE INDICATOR NOT USED IN THIS GAME (NO SCSI DRIVES) OPEN 1&2

J8FR

(NOTE 9) UPPER CENTER NEAR HARD DISK DRIVE JACKS FRONT PANEL DEVICES ONLY RESET PINS ARE USED IN THIS GAME OPEN 1&2

J8A1

(NOTE 10) UPPER RIGHT NEAR BATTERY AND SPEAKER CONFIGU- RATION SELECT

Wiring STARTS SYSTEM SETUP ROUTINE OR OPERATION

5-5 OPEN 1&2 2&3

Page 81

NETWORK INTERFACE CARD ASSEMBLY

20-10550

NETWORK INTERFACE LED INDICATOR STATUS CHART

DESIGNATION LOCATION FUNCTION MEANING

LED 1LEFT CENTERLINK VERIFYNOT IN USE

(LNK) UNDER JACK INDICATOR (NO GAME LINK) ON NORMAL OPERATION BLINKING LINK FAULT (NOTE 1)

RIGHT CENTERACTIVITYOFFNOT IN USE
UNDER JACKINDICATOR(NO DATA)

ON RECEIVING DATA (NOTE 2) BLINKING NORMAL OPERATION

NOTES:

  • Intermittent cable or hub problems may cause blinking. Must be continuous at all times when linked.
  • Blinks as data packets are exchanged. May appear almost continuous during heavy network activity.

Wiring 5-6

Page 82

VIDEO GRAPHICS CARD ASSEMBLY

20-10551

VIDEO GRAPHICS CONNECTOR AND JUMPER STATUS CHART

DESIGNATION LOCATION FUNCTION MEANING SETTING | DEFAULT J1 LEFT CENTER VIDEO GRAPHIC (DB-15 ON SIGNAL INFORMATION (NOTE 1) BRACKET) OUTPUT TO INTERFACE J2-J7 NONE ~ NOT USED

(NOTE 2) JP2 NONE NOT USED

(NOTE 2)

NOTES:

  • Connects to Interface Board Assembly through shielded cable. Does not connect directly to monitor.
  • Manufacturer option connectors and jumpers. Not required for this game.

Wiring 5-7

Page 83

AUDIO AMPLIFIER BOARD ASSEMBLY

04-12529.1

P2

U4] 4

PI

AUDIO AMPLIFIER LED INDICATOR STATUS CHART

DESIGNATION LOCATION FUNCTION MEANING

LED 1 UPPER CENTER FAULT NORMAL (CR1) NEAR C3 INDICATOR OPERATION ON LOCKED UP (NOTE 1) BLINKING OVERLOAD (NOTE 2) LOWER CENTER FAULT OFF NORMAL NEAR U2&U6 | INDICATOR OPERATION ON LOCKED UP (NOTE 1) BLINKING OVERLOAD (NOTE 2)

NOTES:

  • Output protection circuit has been activated. Clear fault and remove power to attempt a circuit reset.
  • Intermittent audio overload or overheating may cause blinking. LED should flash only during start up.

Wiring 5-8

Page 84

DIEGO INTERFACE BOARD ASSEMBLY

04-12522.4

JP1S P14 5 JPZ

JP1

enf] = fo | U2 U3

  • ul44

JP12 r sal

IPS

JPIS

x JZ x JPA IPT PA

DIEGO INTERFACE BOARD SWITCHES

DESIGNATION LOCATION FUNCTION POSITIONS MEANING

$1-3RIGHT CENTERGAME2NORMAL
NEAR JP7 & JP8MODESOPERATION

FIXED IN TEST MODE

RIGHT CENTERCABINETSTANDARD
NEAR JP7 & JP8SIZE25” CABINET

39” CABINET

RIGHT CENTERRESETWATCHDOG
NEAR JP7 & JP8MODESDISABLED

WATCHDOG ENABLED

NOTES:

  • Use S1-3 only during testing or troubleshooting. The game will not start if this switch is left ON.
  • Use S1-4 to set game type. The speakers and leader lights will not work properly if set incorrectly.
  • Use S1-8 only during testing or troubleshooting. The game may lock up or freeze if this is disabled.
  • $1-1, -2, -5, -6, and -7 have no assigned function. Leave these switches in their OFF positions.

Wiring 5-9

Page 85

DIEGO INTERFACE BOARD LED INDICATOR STATUS CHART

DESIGNATION LOCATION FUNCTION | COLOR | STATE MEANING

LED 1MIDDLE CENTER | INDICATOR | GREENOFFNOT IN USE

(D1) NEAR JP12 & U10 ON LOCKED UP (NOTE 1) BLINKING NORMAL OPERATION

LED2MIDDLE CENTER | INDICATOR |REDOFFNOT IN USE

(D2) NEAR JP12 & U10 ON LOCKED UP (NOTE 1) BLINKING NORMAL OPERATION

LEDSMIDDLE CENTER | INDICATOR | GREENOFFNOT IN USE

(D3) NEAR JP12 & U10 ON LOCKED UP (NOTE 2) BLINKING NORMAL OPERATION

LED4MIDDLE CENTER | INDICATOR |REDOFFNOT IN USE

(D4) NEAR JP12 & U10 ON LOCKED UP (NOTE 2) BLINKING NORMAL OPERATION

LEDSUPPER LEFTPOWERREDOFFNO
(D5)NEAR JP13 &L37 | INDICATORPOWER

ON NORMAL OPERATION BLINKING | POWER FAULT (NOTE 3)

NOTES:

1. LED 1 and LED 2 are active on all versions of this board. LEDs may flash together during game start up. If these LEDs are always ON, there may be a fault that has caused the game freeze or lock up.

LED 3 and LED 4 are active on some versions of this board. May flash together during game start up. If these LEDs are always ON, there may be a fault that has caused the game to freeze or lock up.

LED 5 monitors a regulated power supply voltage source. Must be on continuously at all times. Flash or blinking indicates an intermittent connection, a power problem, a circuit fault, etc.

Wiring 5-10

Page 86

DIEGO INTERFACE CONNECTOR AND JUMPER STATUS CHART

DESIGNATION LOCATION FUNCTION MEANING SETTING DEFAULT

J1 & JP1

(NOTE 1) UPPER RIGHT BETWEEN JP2 AND JP16 VIDEO INPUT SIGNALS SIGNALS FROM COMPUTER VIDEO GRAPHICS CARD OPEN Jt ALL JP1 ALL J2 & JB

(NOTE 2) LOWER CENTER BETWEEN JP7 & JP10 SERIAL COMM SIGNALS NOT USED IN THIS GAME (NO USB COMM) OPEN

JP2 UPPER RIGHT BETWEEN J1 & JP6 VIDEO OUTPUT SIGNALS SIGNALS TO GAME VIDEO MONITOR OPEN JP2 ALL

JP3

(NOTE 3) UPPER RIGHT BETWEEN JP1 & JP6 BLUE VIDEO LEVEL MATCHES DRIVE LEVEL TO MONITOR OPEN 1&2 2&3 JP4

(NOTE 3) UPPER RIGHT BETWEEN JP1 & JP6 GREEN VIDEO LEVEL MATCHES DRIVE LEVEL TO MONITOR OPEN 1&2 2&3 JP5

(NOTE 3) UPPER RIGHT BETWEEN JP1 & JP6 RED VIDEO LEVEL MATCHES DRIVE LEVEL TO MONITOR OPEN 1&2 2&3 JP6

(NOTE 4) UPPER RIGHT BETWEEN L7&U1 VIDEO SYNC POLARITY LOCKS VIDEO MONITOR TO SYNC SIGNAL OPEN 1&2 2&3 JP7 LOWER RIGHT NEAR J3 & JP8 PLAYER INPUT SIGNALS SIGNALS FROM SWITCHES AND STEERING WHEEL OPEN JP7 ALL

JP8 LOWER RIGHT NEAR JP7&S1 OPERATOR INPUT SIGNALS SIGNALS FROM CURRENCY AND TEST SWITCHES OPEN JP8 ALL

JPQ CENTER LEFT NEAR JP11 & US WHEEL DRIVER SIGNALS STEERING MOTOR FEEDBACK AND LEADER LIGHTS OPEN JP9 ALL

JP10 LOWER LEFT BETWEEN J2&P1 COIN OUTPUT SIGNALS INDIVIDUAL COIN METER DRIVE CIRCUITS OPEN JP10 ALL

JP11 CENTER LEFT BETWEEN C134 & JPO GAME RESET SIGNAL WATCHDOG TIMER CIRCUIT OPEN JP11 ALL

JP12 CENTER RIGHT NEAR S1&U8 BOARD TEST SIGNALS CONNECTOR USED FOR CIRCUIT DEVELOPMENT OPEN JP12 ALL

JP15 & P14

(NOTE 1)

NOTES: LOWER RIGHT NEAR JP10 & U7 SERIAL COMM SIGNALS DATA EXCHANGE TO COMPUTER CIRCUITS OPEN JP15 P41

  • Connectors wired in parallel. Use based on type of interconnect cable connector.
  • Alternate forms of communications. Not required for this game.
  • Jumper not required for production video monitors. Install for early production Neotec or other units.
  • Jumper factory set for production video monitors. Change for older positive sync video monitors.

Wiring 5-11

Page 87

WHEEL DRIVER BOARD ASSEMBLY

04-11127

Pt

Pa JB i)

WHEEL DRIVER BOARD LED INDICATOR STATUS CHART

DESIGNATION LOCATION FUNCTION | COLOR | STATE MEANING LED 1 RIGHT CENTER | INDICATOR | RED OFF NOT IN USE NEAR C5 & P2 ON NORMAL OPERATION BLINKING | POWER FAULT (NOTE 1)

NOTES:

  • LED 1 monitors a regulated power supply voltage source. Must be on continuously at all times. Flash or blinking indicates an intermittent connection, a power problem, a circuit fault, etc.

Wiring 5-12

Page 88

HYDROTHUNDER

CHAPTER

SIX

TROUBLESHOOTING

NOTICE: The term VGM refers to the video game machine.

CAUTION: This VGM uses complex electronic components that are very sensitive to static electricity. Observe the following precautions before handling VGM electronics. Failure to do so may void your warranty and could damage electronic assemblies.

Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge. Before touching or handling electronic assemblies, discharge static electricity on your body. To discharge this static, begin by connecting the line cord to a grounded outlet. Don’t turn on the VGM! Next, touch the safety ground stud of the power supply chassis. Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport VGM circuit boards. Transport the hard drive in its shipping container. Don’t remove or connect electronic assemblies when cabinet power is on. Otherwise, you'll damage electronic assemblies and void the VGM warranty. After you complete maintenance or service, replace ground wires, shields, safety covers, etc. Install and tighten ground and mounting screws.

Troubleshooting 6-1

Page 89

Coin Mechanism and Pricing Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« VGM (video game machine) accepts currency or tokens, but number of credits per coin or bill is incorrect. Improper settings at Pricing Menu Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Diagnostics Menu, choose SWITCH TEST. Use tests to confirm operation of switches. From Adjustments Menu, choose PRICING MENU. Verify that units and credits are set correctly.

Faulty wiring Check that cabinet wiring is correct for this VGM. Assure that coin meter and coin switches connect properly to control input wires.

« VGM won't accept currency or tokens.

¢ — VGM won't start. Improper currency Unlock and open cash door. Empty cash box. Inspect revenue for counterfeit currency. Check vault. Remove any items that block path from mechanism.

« Audio and video are present. Faulty coin mechanism Unlock and open coin door. Check each mechanism for proper mounting. Remove mechanism. Clear currency path. Reinstall mechanism and latch it.

Tilted coin mechanism or VGM Valo

e Verify that mechanism is level after doors close. Repair or replace coin door if it is bent or damaged. If necessary, adjust cabinet leg levelers to keep mechanisms vertical. ¢ — Coin indicators don't light Burned-out bulb Burned-out bulbs may appear white or darkened. Check continuity with DVM. Replace burned-out bulb with same type. Open fuse circuit ENa|N Check fuse continuity with DVM. If fuse is blown, replace fuse with same type. If fuse isn't blown, check wiring.

CAUTION: Don’t remove or install any connector when power is turned on. Installation under power will damage the circuit boards or hard disk drive and void the warranty.

Troubleshooting 6-2

Page 90

VGM Startup Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« VGM (video game machine) doesn't start.

« VGM appears completely non-functional.

  • No audio

¢ No illumination

« No video display Power problem Check that VGM power switch is on. Inspect computer to see if fans are turning. If not: Is computer power supply connected to its power cable? Is computer power supply turned on? Plug VGM into AC power outlet. Verify presence of AC line voltage.

Improper line voltage switch setting Turn off VGM power. Unplug AC line cord. Check line voltage switch. If necessary, set it to agree with local AC line voltage. Retest VGM.

Open fuse Turn off VGM power. Examine AC fuse on power chassis, under computer. Examine DC fuses on cabinet wall or electronic equipment shelf. Replace faulty fuses with identically rated parts. Turn on VGM power. If fuse opens again, check DC wiring harness and connectors.

Faulty wiring Remove line cord. Test line cord, power plug, and IEC connector for breaks or damage. Verify continuity of each wire in cord. Install cord at power chassis. Press connector firmly to seat it. Check computer cord in same manner. Assure that cabinet wiring harness connectors fully seat in corresponding power supply and board connectors. Inspect wiring for breaks or damage. Arcade computer problem Turn off power for one minute and turn VGM on again. Power On Self-Test checks electronics. Screen may report errors. If video circuits don’t operate properly, computer produces series of beeps. (See Error Message Troubleshooting Table.)

FILTER

MOTHERBOARD “S__RESET O POWER SUPPLY

CABLE

Location of Power Supply

Troubleshooting 6-3

Page 91

VGM Startup Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

« VGM (video game machine) appears non-functional.

e Currency acceptor price indicator is illuminated. Power problem Inspect circuit boards under low-light conditions. LEDs glow if processor circuits receive voltage. Fan should be turning. These indications prove presence of DC from power supply. Still,

voltagesor signalsmaynotbenormal.

Computer has no internal LEDs. Turn on VGM power. Using 20-volt DC setting on digital voltmeter, measure DC voltages at power connector pins. (Power supply voltage isn’t adjustable.) Using 2-volt AC setting on digital voltmeter, measure same DC voltages as above. Any reading here indicates that supply voltages are unstable and may contain ripple or noise.

Faulty wiring Turn off VGM power. Assure that wiring harness

connectorsfullyseatontomatingboard

connectors. Verify that harness connects to computer. Check other connectors in same way. Improper jumper or DIP switch settings Verify that circuit board jumpers are set as intended. Check DIP switch settings.

Faulty circuit boards or arcade computer Run power-up self-test sequence. Note errors or failures during tests. Compare LEDs with LED indicator status charts. Note discrepancies. Turn off computer. Wait for hard disk to stop

spinning.LeaveVGMpower on.Loosen

computer case thumbscrews and lift off cover. Turn computer power on. Listen for beeping sounds. Compare beeps with Error Message Troubleshooting Table.

CAUTION: Don’t remove or install any connector while power is turned on. Doing so will damage circuit boards or hard disk drive, and void warranty.

Front View of Coin Door —— PRICE INDICATOR

—— REJECT FLAPS

Troubleshooting vom wet EH “a j spre ona ve tte a

Interior View of Electronics

6-4

Page 92

VGM Startup Troubleshooting Table, continued

« VGM accepts currency or tokens.

« Audio and video are present. SYMPTOM CAUSE REQUIRED ACTION

Unlock and open coin door. Check each «¢ VGM (video game machine) | Faulty coin currency acceptor to assure proper mounting. doesn't start. mechanism Verify that each release latch is closed and locked. Does mechanism accept and reject currency correctly? Test mechanism with good and bad coins. Inspect to see if external acceptor indicators (Pricing, Flashing Arrows, etc.) are lit. Verify that each acceptor operates properly by placing it in working VGM. Replace bad parts.

Faulty switches Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Diagnostics Menu, choose SWITCH AND LAMP. TESTS. Use tests to confirm operation of each switch in VGM. Assure that no loose parts or wires are caught in switch contacts. Check for continuity in each suspect switch connection (Common to Normally Open or Common to Normally Closed). Replace faulty switches (bent levers, broken actuators, etc.).

Faulty wiring Assure that no wires are caught in hinges, latches or switch contacts. Check wiring continuity from circuit board connectors to acceptors.

Troubleshooting 6-5

Page 93

Audio Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

Enter Menu System by pressing and holding

«No audioImproper volumeTEST MODE switch. From Operator (Main)

setting Menu, choose VOLUME MENU. Check that «Video is present Attract Music is on (enabled). Verify that all volume levels are set well above zero. If

¢VGM (video game machine)necessary, change levels to make VGM audible.

appears to operate normally Turn off VGM power. Assure that wiring harness Faulty wiring connectors attach and fully seat onto mating board connectors. Verify that harness connects to computer. Check audio cable connectors in same way. Faulty or obstructed Remove grilles and inspect speakers. Free speaker speaker cones, terminals, mounting screws and magnets of loose parts or wires. Faulty Audio Board Verify proper operation of Audio Board by placing it in working VGM. Check that cabinet wiring is correct for this VGM.

¢Constant low hum from allFaulty wiring2.Verify that cabinet wiring provides separate

speakers. wires (not common return) for each speaker. Check connection of all cabinet ground wires.

  • Run power-up self-test sequence. Note errors Faulty Audio Board that VGM finds during tests. Compare Diego Board LEDs with LED indicator status charts.
Note discrepancies.
  • Verify that Audio Board operates by placing it in working VGM. Replace bad parts. Using 2 Volt AC setting on digital voltmeter, Faulty power supply measure voltages at speaker terminals. Any reading indicates unstable supply that may contain ripple or noise.
  • Turn off VGM power. Remove grilles and check
©Audio is distorted, muffled or | Faulty or improperspeakers. Assure that speakers are full range
has missing frequencies.speaker(100 to 10,000 Hz response) and rated for at

least 20 watts. Woofers must be rated for at least 40 watts.

  • Verify proper speaker operation by connecting speaker in question to working VGM. Multiple-speaker installations: Check for Faulty wiring reversed wires at one speaker. Weak low frequencies and thin or hollow sound quality is symptom of incorrectly phased speakers. Sound tests may not detect this condition, but you can hear it during VGM operation.
  • From Diagnostics Menu, choose SOUND TEST.
«Dead sound channelFaulty speakerRecheck speakers with audio signals provided

by test.

  • Verify proper speaker operation by connecting speaker in question to working VGM. Run power-up self-test sequence. Note errors Faulty circuit board that VGM finds during tests. Compare circuit board LEDs with LED indicator status charts.
Note discrepancies. Verify that cabinet wiring is correct. Assure that Faulty wiring all speakers connect to audio wires. Audio cable must be fully seated in Computer Line Output Jack. Check for broken or shorted wires.

Troubleshooting 6-6

Page 94

Error Message Troubleshooting Table

Power-On Self-Test Beep Codes (Audio beeps only. Video may or may not be present): See Note 1 MESSAGE MEANING REQUIRED ACTION

No beepNo system powerCheck power supply and cables
1 continuous beepPartial system powerCheck power supply and cables
1 short beepNormal start; no errorsCheck other VGM components
2 short beepsProcessor problemCheck processor/fan module
3 short beepsGraphics initialization problemCheck Video Board, cables
4 short beepsProcessor problemCheck processor/fan module
5 short beepsInsufficient system memoryCheck DIMM circuit modules
6 short beepsPeripheral problemCheck other VGM components

System Error Message Codes

(One or more lines of text appear on video screen): See Note 2 MESSAGE MEANING REQUIRED ACTION CONFLICTING UNIT ID: Linking problem Check for unique unit ID number GAME STARTUP: Normal start; no errors Check other VGM components VERSION MISMATCH Software problem Check for differing revision level XXXX DATA LOAD: Corrupted files or failing circuits Check named drive or circuit XXXX INIT OR INIT FAILURE: Circuit/file initialization problem Check named drive or circuit Notes

  • The audio buzzer that generates 1 kHz beeps is on the computer, inside the VGM (video game machine). If hearing beep codes is difficult, remove the cabinet doors and computer cover.
  • Arcade Computer circuit boards resemble those in personal computers. Yet Midway engineers reprogrammed the boards for application to this VGM. Power-On Self-Test codes are unique to the Arcade Computer in this VGM.
  • Wiring or peripheral circuit problems may not trigger on-screen error messages. You may discover difficulties during Menu System diagnostic or calibration procedures.
  • Call your authorized distributor for help with unresolved error messages.

NOTICE: Don’t attempt to move computer circuit boards into alternate slots. Midway assigned boards to specific slots. The custom operating system won't recognize improperly placed boards, even though they function normally.

MOTHERBC

Troubleshooting 6-7 Location of Beeper in Arcade Computer

Page 95

Link Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

Can't connect VGMs (video game machines) together Faulty wiring Don't extend linking cables that come with VGM.

InstallrequiredcrossoverbetweenVGM

cabinets. Each coupler connects two cabinets (one pair). Don't use standard telephone type couplers or wiring to link cabinets. Use only 10Base-T, Ethernet-type, Category 5, twisted-pair wiring for VGM data.

Improper linking hardware Use required network hub for your local network. Hub Link Kit permits up to four cabinet connections. Cabinet array completion requires basic kit brackets and spacers.

VGM doesn't recognize other players in linking operation

VGM functions normally by itself Improper settings Record any error messages that occur during self-test.

FromOperator(Main)Menu,choose

Adjustments Menu. Then select Linked Play Adjustments Menu. Assure that you've set LINKED PLAY to ON. Be sure that each VGM has unique ID number. Power problem If hub is in use, verify that power is applied. AC adapter wires are thin and easily damaged.

Faulty wiring (3 or more cabinets) Inspect hub indicator lights. Each active port should have illuminated indicator. If cable connects, and that position has no lit indicator, check for cable continuity from hub to cabinet. Assure that no loose wires catch in hinges, doors, or under cabinet. Verify that linking cable connects to Network Board at each VGM's computer. Verify that each linking cable operates properly by placing it in working VGM.

Some VGMs in group link properly, while others don’t Improper hub switch setting Assure that switches on hub are set correctly according to Hub Link Kit instructions. (Networked cabinets don't require couplers. Hub has electronic crossover.) Inspect hub indicator lights for link activity. See manufacturer's literature for diagnostics.

Wrong software version Verify that all linked cabinets use same software

version.Otherwise,linkedcabinetswon't

recognize each other. Contact your distributor.

Faulty wiring (2 cabinets) Insert crossover connections between coupled cabinets. Standard couplers appear identical to devices supplied with cabinets, but don't include internal crossover. Verify that each linking crossover coupler operates properly by placing it in working link between two cabinets.

Faulty wiring (3 or more cabinets) You used additional crossover connector and cable to extend VGM or hub link connection.

Twocrossoverscancelandcausesame

problem as no link crossover. Connect cables directly to hub. Don't use crossover coupler and hub together in single network. Separate communications wiring from other wiring. Wires that must cross should cross at right angles to limit noise pickup.

Troubleshooting 6-8

Page 96

Player Control Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

e Intermittent or completely non-functional player controls

« VGM (video game machine) starts normally. Faulty switches or lamps Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Diagnostic Menu, choose SWITCH TEST. Run tests to confirm switch operation. Check for loose parts or wires caught in switch contacts. Check continuity at each switch connection (Common to Normally Open or Common to Normally Closed). Verify that control operates properly by placing it in working VGM. Verify that dashboard switch light bulbs are type specified in parts listing. Other types light, but may produce too much heat. Eventually excess heat may cause switches to bind. Faulty switch wiring Check for wires caught in door hinges, latches, or switch contacts. Verify that harness connectors are attached and fully seated. Assure that control switches connect properly to control input wires. Check that cabinet wiring is correct for this VGM. e Steering pulls to one side Faulty Wheel Driver Board Find power amp on Wheel Driver Board's large heatsink. Test and replace bad part or board.

How to Adjust Belt Tightness

Troubleshooting 6-9

Page 97

Player Control Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

Sloppy, unpredictable or ineffective steering

Video appears on screen

VGM (video game machine) starts normally Blocked or faulty fan With VGM power on, check airflow near each computer fan. Case cooling fans are intake fans. Power supply fan is exhaust fan. Assure that nothing blocks airflow.

Faulty mechanical parts Turn off VGM power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if your VGM has one) over motor. Inspect for faulty or worn belts, bearings, couplings, gears, etc.

Faulty Wheel Driver Board Inspect Wheel Driver Board under low-light conditions. LEDs glow if motor driver circuits receive AC power from transformer. (Voltages or signals may or may not be normal.) Examine fuses and cables on Wheel Driver

Board.Replacebadfuses.Usingdigital

voltmeter, verify AC voltage between each fuse

holder andground.Youshouldmeasure

approximately 25V. See Wiring Diagram. Using 20 VAC setting on digital voltmeter, measure DC voltage at motor. Don't move steering wheel, drive belt, or motor while making

thismeasurement.Anyreading _ indicates

unstable supply that may contain ripple or noise. Verify proper operation of Wheel Driver Board by placing it in working VGM.

Loose or worn drive belt Turn off VGM power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if your VGM has one) over motor. Inspect for faulty or worn belts, bearings, couplings, gears, etc. If drive belt isn’t worn or damaged, check its tightness.

No wheel feedback

Steering aims vehicle as expected Improperly set feedback

FromDiagnosticsMenu,chooseFORCE

FEEDBACK ADJUSTMENT. Set feedback to match player requirements. Maximum force may be too extreme for very young or inexperienced customers.

Faulty circuit Examine fuses and cables on Wheel Driver Board. Check cables and wiring between computer, interface, driver and motor. Check resistance of motor series resistors Replace bad parts.

Faulty motor Turn off VGM power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if you VGM has one) over motor. Unscrew caps. Inspect motor brushes. Replace worn parts.

Troubleshooting

Page 98
  • STEERING WHEEL

HIG

Player Panel Controls

WARNING: The Wheel Driver Board heatsink, power resistors, and other component may be very hot. The DC Motor in the steering wheel may also be hot. iS

SEMELY JRE

) STEERING

a TOOTHED BELT—

STEERING

Steering Components

Troubleshooting 6-11

Page 99

Video Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

Verify connection of AC Power to video monitor. « Monitor appears non- Power problem Inspect CRT neck in dim light. Glowing filament functional near CRT base proves that some monitor circuits receive power. Still, voltages or signals

  • — Audio is present may not be normal.
  • Turn off VGM power. Verify that video signal and
  • VGM (video game machine) | Faulty wiring Remote Adjustment Board connectors seat controls operate normally properly on Video Monitor Board.
  • Assure that video cables connect to circuit boards and computer.
  • Assure that no wires are caught on chassis or mounting brackets. Improper monitor Check that BRIGHTNESS (intensity) and adjustments CONTRAST are set above their minimum levels.
  • Examine AC line fuse on Video Monitor Board. If Faulty monitor fuse is faulty, replace it with identical fuse. circuitry 2. If fuse is good: Verify that video monitor operates correctly by placing it in working VGM.
  • If monitor is bad: Check monitor power supply.
  • If power supply is good: Check monitor horizontal output transistor and related circuitry.
WARNING: HIGH VOLTAGE. VGM (video game machine) monitors generate and store potentially lethal high voltages. Avoid touching any part of the monitor until power has been off for some time. A picture tube can maintain a hazardous charge for up to several days. Only qualified technicians should service monitors. Turn off the power, unplug the VGM and discharge the CRT before attempting service. Even properly discharged tubes can revert to a highly charged state, without reapplication of power.
WARNING: In normal operation, the monitor doesn’t require isolation from AC line voltage. During bench servicing, you may need to operate the monitor outside the cabinet. If you do, isolate the monitor from line voltage with an isolation transformer.

Troubleshooting 6-12

Page 100

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

VGM (video game machine) doesn't appear

No audio

Power-up self-test runs Floppy disk in drive Check floppy drive for diskette. If you find disk, eject it. Leave VGM power on. Turn off computer. Wait for hard disk to stop spinning. Turn on computer.

Faulty wiring Loosen computer case lid thumbscrews and lift off cover. Assure that hard drive ribbon cable connector is fully seated into mating connector on motherboard. Check hard drive power cable.

Improper components Verify that hard disk drive is correct for this VGM. Label on drive records manufacturer name, assembly number and program version. Verify that circuit boards are correct for this

VGM.Labeloneachboardrecords

manufacturer name, assembly number and hardware version. Verify that ROM instruction set is correct for this VGM. VGM set includes more than one ROM. Label on each ROM records assembly number and software version.

Hard drive problems Turn computer on. Immediately look under hard drive. Hard Drive Activity LED flashes if drive is operating properly. Allow VGM to load normally. Note and record any error messages that occur during self-test. Remove hard drive and install it in working VGM. If symptom recurs there, hard drive is faulty. Replace it.

Blotches of color appear on screen Picture tube aperture mask is magnetized Remove diskettes from room. Demagnetize monitor with external degaussing coil. Take care not to magnetize neighboring VGMs. Monitor may be on or off for this procedure.

White areas in center of screen appear tinged with color

Object edges have fringe of one or more colors Picture tube purity or static convergence is out of alignment Turn on VGM. Press and hold TEST MODE to enter Menu

System.At Operator (Main)Menu,select

Diagnostic Menu. Then select Monitor Patterns Menu. Run through Crosshatch, Red, Green and Blue screens to find clearest display of problem. Display screen with greatest problem. Display Crosshatch Screen. Locate purity and static convergence ring magnets on back of monitor neck. Watch screen in mirror. Adjust

magnetstominimizeproblem.Follow

instructions from monitor manufacturer. Display Crosshatch Screen. Touch up adjustments while watching screen in mirror.

CAUTION: Don’t operate the monitor without its Remote Adjustment Board.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

Troubleshooting 6-13

Page 101

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

White areas at screen edges appear tinged with color

Dots at screen edges appear ovoid or cylindrical Picture tube dynamic convergence is out of alignment Have service bureau dynamically reconverge monitor. This procedure requires removing and repositioning yoke. Service bureau must follow instructions from monitor manufacturer.

Video tears or rolls, or has black bar down middle of Faulty wiring

Checkconnectorsandcablesforwiring

continuity. Video cables connect computer to circuit boards, and then to video monitor.

screen2.Assure connection of all cabinet ground wires,

especially at video monitor chassis.

  • Verify that video monitor operates correctly by Faulty monitor connecting it to working VGM.
circuitry2.Assure that video monitor is correct type for this

VGM. Video monitors with wrong resolution can’t lock sync.

  • Check to see if Video Board puts out type of Improper sync signals sync that your monitor requires.
  • Verify that jumpers are set correctly for monitor.
  • If necessary, change video sync jumper on Diego Board. Refer to Wiring chapter for details.
ElectromagneticMovecabinetfarawayfrommachines,

fields appliances, or VGMs (video game machines).

Missing colorsCheckconnectorsandcablesforwiring

Faulty wiring continuity from circuit boards to video monitor. Faulty monitor color Verify that video monitor operates correctly by drive circuitry connecting it to working VGM.

  • Turn on VGM.
One color is dimmer orMaladjusted color2.Enter Monitor Patterns Menu.
brighter than othersbias pots3.Watch Color Bars screen in mirror.
  • Adjust three bias pots for best colors. (Most Whites appear tinted monitor neck boards include these pots.)
everywhere on screen5.Also check White Screen. Touch up controls.
  • If whites still seem tinted, have service bureau rejuvenate picture tube.
  • Watch Color Bars screen. Adjust BRIGHTNESS
Picture is dim or fadedMaladjustedand CONTRAST pots for greatest number of

BRIGHTNESS pot or grays. You'll find these pots on Monitor Remote ssubnormal picture Control Board, behind coin door.

tube emission2.If pots have no effect, have service bureau

rejuvenate picture tube. Enter Monitor Patterns Menu. Watch Crosshatch

Picture is too narrowMaladjusted WIDTHScreen while adjusting WIDTH pot for best

pot picture. You'll find this pot on Monitor Remote Control Board, behind coin door.

  • Enter Monitor Patterns Menu. Watch Crosshatch
Picture is too shortMaladjusted HEIGHTScreen while adjusting HEIGHT pot for best

pot or damaged picture. You'll find this pot on Monitor Remote vertical circuit Control Board, behind coin door.

  • If pot has no effect, service vertical output circuit. Enter Monitor Patterns Menu. Watch Crosshatch Picture seems shifted to one | Maladjusted Screen while adjusting HORIZONTAL POSITION
sideHORIZONTALpot for best picture. You'll find this pot on Monitor

POSITION pot Remote Control Board, behind coin door.

  • Substitute working yoke.
Keystone-shaped pictureShorted turns in yoke | 2.Have service bureau converge monitor.

3.__ Retest monitor.

Troubleshooting

Page 102

Software Update Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« Update didn’t work

e After update procedure, screen reports lower than latest version You skipped steps or performed them out of sequence. Return update components to kit, reinstall original parts in cabinet, and try process again.

You connected linked VGMs (video game machines) to cabinet being updated. Network communication circuits may have prevented full update. Turn off power to all connected cabinets. Perform update on one cabinet at time. If power is off, you need not disconnect linking cables. Installation error may have damaged device. Inspect for bent or broken pins. If you have another kit, try it. Ask your distributor to check your floppy disk.

NOTICE: Someday, software updates for your VGM (video game machine) might become available. These upgrades may improve your VGM’s performance or add new 7 VGM features. Such upgrades tend to appear sometime after factory first releases VGM. Contact your distributor for information about updates.

Troubleshooting 6-15

Page 103

Miscellaneous Problem Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

or non-functional

« VGM (video game machine) starts and plays normally e Marquee lamp is intermittent | Faulty fluorescent tube Remove fluorescent tube from its sockets. If you find cracks or darkened ends, install new lamp. Clean tube. Check continuity of both fluorescent tube filaments. Verify that fluorescent tube operates by placing it in working VGM. Faulty lamp fixture Verify that lamp pins make good connection with socket contacts. Faulty wiring Measure fluorescent lamp AC voltages. Check wiring and connector continuity from AC power chassis to lamp assembly.

several hours of use

  • Cabinet becomes warm after « VGM operates normally Obstructed fan Check bottom and rear of cabinet for blocked airflow. Move VGM away from sources of heat. Turn off VGM power. Remove dust from vent holes with high-power vacuum cleaner. Faulty wiring Check fan wiring and connectors.

Faulty fan Check operation of all fans.

screen « Error messages appear on Faulty hardware Check any assembly (RAM, ROM, Battery, etc.) identified in error messages. Call your authorized distributor for help with unresolved screen messages.

Fan Location and Mounting

Troubleshooting

Page 104

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 105

WARNINGS & NOTICES

WARNING USE OF NON-MIDWAY PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR EQUIPMENT DAMAGE! USE ONLY MIDWAY AUTHORIZED PARTS.
  • Use only authorized components and parts. Failure to do so will void warranty and may result in incorrect and/or unsafe operation. Substitute parts or modifications may void EMC directive or FCC type acceptance.
  • This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under federal law. This also applies to MIDWAY GAMES INC. and HYDROTHUNDER logos, designs, publications and assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY GAMES INC. components.
WARNING Prevent shock hazard and assure proper game operation. Plug this game only into a properly grounded outlet. Do not use a cheater plug to defeat the power cord's grounding pin. Do not cut off the ground pin.
WARNING A very small portion of the population has a condition which may cause them to experience epileptic seizures or have momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition.

If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g. seizures or loss of awareness), immediately consult your physician before using any video games.

We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

NOTICE - FCC COMPLIANCE LABEL

NOTICE When MIDWAY ships a game, it is in compliance with FCC regulations. The FCC label on your cabinet is proof. If this label is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game does not have an FCC label, contact MIDWAY immediately.

NOTICE No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.

For Service: Call your Authorized MIDWAY GAMES INC. Distributor.

MIDWAY GAMES INC. 3401 N. CALIFORNIA AVE. CHICAGO, ILLINOIS 60618-5899 UNITED STATES OF AMERICA

Entire contents of this manual copyright © 1999 MIDWAY Games Inc. All rights reserved.