Sente SAC 1A Service Manual (FORM-00495-8505)
SAC 1A (Bally Sente) · Manual · 92 pages · 47 sections · original scan
AC 1A
SERVICE MANUAL
10601 W Belmont Avenue Franklin Park. Illinois 60131 USA
Phone (312) 451-9200 Cable Address MIDCO Telex No.: 72-1596
FORM-00495-8505
|. SYSTEM INFORMATION
SAFETY
The following safety hints apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.
WARNINGS
AC POWER CONNECTION. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game's power supply and the electronic chassis assembly.
PROPERLY GROUND THE GAME. Customers may receive an electrical shock if this game is not properly grounded! To avoid shocks, do not plug in the game until it has been inspected and properly grounded. Sente games should only be plugged into a grounded 3-wire outlet. Customers may receive an electrical shock if the contro! panel is not properly grounded! After servicing any parts on the panel, check that the grounding wires are secure. Only then should you lock up the game.
DISCONNECT POWER DURING REPAIRS. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the monitor. extra precautions must be taken to avoid electrical shock because high voltages may exist within the display circuitry and cathoderay tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metai objects! Always discharge the second anode from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again.
USE THE PROPER FUSES. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type. voltage rating, and current rating. In addition, the fuse cover must be in place curing game operation.
HANOLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly eight feet or more from the implosion.
PROPERLY ATTACH ALL CONNECTORS. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.
...When A Game Loses Its Appeal — You Plug A New Cartridge Into Game Frame.
Because different locations require different games, Bally Sente offers a wide selection of interchangeable games — eight entirely different games. Change Games Fast With the new Sente System there is no need to truck 350-pound games from location to location. In fact, the only “moving parts’’ are contained in the easy-to-carry SAC PAC' which makes changing games quick and easy. SAC PAC game kits include a 14-ounce game cartridge and a bright attract panel that slip quickly into the game frame. And, unlike other systems, the SAC PAC includes a complete new control panel specifically designed for each game. This means that Sente game designers are never limited to create a game around an existing set of controls that cannot be changed. With the Sente System all you'll need to change a game is an Allen wrench and about 15 minutes. Each game is designed to create new excitement. New levels of player involvement. With highly detailed graphics and sophisticated sounds. Game Production Bally Sente game production will be orchestrated by another Bally subsidiary, Bally Midway Manufacturing at its Franklin Park, Mlinois, facility near Chicago. Bally Midway has manufactured several of the most successful video games in the industry, including “Pac-Man” and ‘Ms. Pac- Man” and “Space Invaders’’. SAC 1 games which made their world premiere in Chicago are: © “Chicken Shift’ in which four fertile hens send their eggs on a harrowing journey down player controlled ramps and tubes on the way to awaiting cartons, © “Goalie Ghost’’ where the player directs the “‘split screen” actions of a fast moving goal defender. © “Snacks N’ Jaxson’’ features a ravenous clown who seeks to devour floating foods as they guide around his surrealistic kitchen. © “Off The Wall’, a combination of paddle ball, ten-
nis and ping pong that gives the participant the chance to
ricochet the ball around the court and score a point on his opponent. © “Stocker’’, a speedy coast to coast highway racing game that gives players the chance to conserve fuel, avoid obstacles and display driving skills and fast reaction times in a cross country race. © “Hat Trick Hockey Game”, each player guides one hockey player over the ice using a joystick for movement and a button to take shots. The joystick is also used to move the players goalie. The game may be played by one or two players. The movement of hockey players over ice is tealistically portrayed in the game. © “Trivial Pursuit’ this new game is compatable with all Sente Arcade Computer (SAC 1) interchangeable game system offerings.
Technical Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual
As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet.
After ail the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Harness Component Troubleshooting
Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned, li the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of testcoins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details).
If the quarter is not returned and there is no game credit, the cause of the ma!function may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedutes. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure If the trapped coin is not returned when the wiper lever is actuated, you may have an accepior jammed by a slug, gummed up with beer, a jammed coin chute, or mechaniéal failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO. NC, and C terminals. Wnen not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit
lf the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. if you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the termina! contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. |f you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.
HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. if the new one aiso blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, contro! panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. in many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
CONVERSION PROCEDURE FOR SAC 1A OR SAC 14
To Change Attract (Header) Art
1.
2. 3. 4. 5. 6. Remove bolts holding in Attract Retalner located at top front of cabinet. Remove Attract Retainer. Slide Attract Glass up and out of cabinet. Remove old Attract Art and replace with new Attract Art. Slide Attract Glass containing new are back into cabinet. Replace and secure Attract Retainer. Clean front of Attract Glass.
- To Change Control! Pane! Insert Assembly (SAC 1A or SAC 1)
1. 2.
3.
5e
6.
7. 8. 9. Power off SAC 1A (SAC 1) unit using switch at rear of cabinet. Unlock Coin Mech door and reach through to unlatch large front door from Inside cabinet. Untatch two (2) clamps locating inside the cabinet at each end of Control Panel. Disconnect the Controi Panel Insert Assembly harness from the main harness of SAC 1A (SAC 1) unit. SAC 1A UnIt: Swing out Control Panel on its hinge. SAC 1 Unit: Lift Control! Panel up, slide to right and pull down to remove. Carefully pul! Control Panel harness wiring out of opening at rear of Control Panel tray. Remove bolts and nuts securing the old Control Panel Insert Assembly to the Control Panel. Remove old Insert Assembly. instal! new Control! Panel Insert Assembly by reversing this procedure, Power on SAC 1A (SAC 1) unit using switch at rear of cabinet. Play game to check If ali switches and controls are working properly.
To Change Game Cartridge
1. 2.
8. 9. 10. We 12.
BE SURE Power off SAC 1A (SAC 1) unit using switch at rear of cabinet. Unlock Coin Mech door and reach through to unlatch large front door from inside cabinet, Find Game Cartridge On/Off Switch located at bottom front right of Electronic Chassis just Inside large front door (this switch may be used to power unit on and off In place of switch at rear of cabinet). Turn Game Cartridge On/Off Switch off to permit Game Cartridge to slide out of Electronic Chassis. Slide oid Game Cartridge out of chassis. Slide new Game Cartridge between runners to plug into the Main PC Board, Be sure Game Cartridge Is securely plugged In. ROMs on the Game Cartridge should be facing to the left as you look Into the cabinet. Turn Game Cartridge On/Off Switch back on (this also focks cartridge into place). Check game option switch settings. Close and latch targe front door. Close and lock Coin Mech door. Power on SAC 1A (SAC 1) unit using switch at rear of cabInet. Play game to test If unit is working properly.
TO SAVE GAME CARTRIDGE, CONTROL PANEL INSERT, AND ATTRACT (HEADER FOR REUSE).
- [f new Control Pane! Insert Assembly is Included with your kit,
TO SERVICE CONTROL SHELF - UNLATCH 2 CLAMPS ON EACH SIDE OF CABINET.
FOR ACCESS TO VOLUME CONTROL AND FUSES - REMOVE 2 SHIPPING SCREWS FROM HAND PULL BRK’T AND PULL CHASSIS OUT TO ITS STOP. THIS WILL EXPOSE THE VOLUME CONTROL AND FUSES.
INCREASE am
VOLUME OD contro.
3 AMPS
POWER SUPPLY
40 AMPS O-—O gio-Bto
TO REMOVE ELECTRONIC CHASSIS FROM CABINET - 1, DISCONNECT ALL CABLES CONNECTED TO CHASSIS FROM CABINET & CONTROL SHELF.
- LIFT CHASSIS OVER STOP BRK'T AND SLIDE OFF SHELF. RETURN CHASSIS IN REVERSE ORDER.
SWITCH SETTINGS FOR SAC 1 GAMES
CHICKEN SHIFT
GOALIE GHOST
HAT TRICK
OFF THE WALL
SNACKS'N JAXSON
SNAKEPIT
TRIVIAL PURSUIT
Cc. P. Ue BOARD REFERENCE DRAWING
aw OPTION SWITCH LOCATED AT "G-1"
OPTION SWITCH LOCATED AT "Ho"
1234567 8 OUUUG00)+
Ie
OFF ON OFF ON
ON OFF ON OFF In
OFF OFF ON ON
OFF OFF OFF
OFF ON
ON OFF ON OFF ON OFF ON OFF OFF OFF ON ON
ir
ON ON OFF OFF ON ON OFF OFF fw
OFF ON
ON ON ON ON OFF OFF OFF OFF
* GIMME A BREAK Option Switch Settings
Gl
& Z 8
*
*
+
OFF oN OFF * ON OFF on *
6 i 8
*
*
oN *
OFF on oN * OFF ON oN OFF OFF OFF BONUS AT 12 BALLS BONUS AT 10 BALLS BONUS AT 8 BALLS BONUS AT 6 BALLS 14 INITIAL sHOTS 12 INITIAL SHOTS 10 INITIAL SHOTS 8 INITIAL sHOTS l or 2 PLYR/CRDT 1 PLAYER/CREDIT UPRIGHT CABINET COCKTAIL CABINET KEEP 5 HI SCORES KEEP ALL HI SCORES NO ATTRACT SOUNDS ATTRACT SOUNDS
FREE PLAY 1 COIN/1 CREDIT 1 COIN/2 CREDITS 2 COINS/1 CREDIT NO BONUS COINS COINS ADDS 1 COINS ADDS 1 COINS ADDS 1 COINS ADDS 2 BONUS BONUS BONUS BONUS BONUS BONUS COIN COIN COIN COINS COIN COINS COINS COINS ADDS COINS ADDS 5 COINS ADDS 3 BONUS LEFT COIN MECH X 1 LEFT COIN MECH X 2 RIGHT COIN MECH RIGHT COIN MECH RIGHT COIN MECH RIGHT COIN MECH VaR Rwn
De OS >< aur
= RECOMMENDED SETTINGS
SNAKEPIT Option Switch Settings
Gl
| 2 | 2 | 3 | 4 | 8 | 6 | ZF | 8 |
| OFF OFF | XX XX | BONUS AT 40,000 | |||||
| ON | OFF | XX | XK | BONUS AT 30,000 | |||
| OFF ON | KX | XX | BONUS AT 20,000 | ||||
| *ON ON | XX XX | BONUS AT 10,000 | |||||
| OFF OFF XX | XX | 5 LIVES |
*ON OFF XX XX 4 LIVES
| OFF ON | XX | KX | 3 LIVES |
| ON | ON | XX XX | 2 LIVES |
| XX XX | “OFF | EASY |
XX XX ON HARD
| XX XX | OFF | NO ATTRACT SOUNDS | |
| XX | XX | *ON | ATTRACT SOUNDS |
HI
| 2 | 2 | 3 | 4 | 8 | 6 | 7 | 8 |
| OFF OFF XX | XX | XX XX | XX | 1 COIN/1 PLAY | |||
| OFF ON XX | XX XX | XX | XX | 1 COIN/2 PLAYS | |||
| ON | OFF XX | XX | XX | XX XxX | 2 COINS/1 PLAY | ||
| ON | ON | XX | XX | XX | XX XX | FREE PLAY | |
| XX | XX | XX | *ON | KEEP ALL HIGH SCORES | |||
| XX | XX | XX | OFF | KEEP 5 HIGH SCORES |
- = RECOMMENDED SETTINGS
HAT TRICK Option Switch Settings
Gl
| 2 | 2 | 3 | 4 | 5S | 6 | 2 | 8 |
| OFF OFF OFF XX | XX XX | XX | TIME GAME - 3:00 | ||||
| ON OFF OFF XX | XX | XX | XX | TIME GAME - 2:45 | |||
| OFF ON OFF XX | XX | XX | XX | TIME GAME - 2:30 | |||
| ON ON OFF XX | XX | XX | XX | TIME GAME - 2:15 | |||
| *OFF OFF ON | XX | XX | XX XX | TIME GAME - 2:00 | |||
| ON OFF ON | XX | XX | XX XX | TIME GAME ~- 1:45 | |||
| OFF ON | ON | XX | XX | XX XX | TIME GAME - 1:30 | ||
| ON ON | ON | XX | XX | XX XX | TIME GAME - 1:15 | ||
| XX | XX | XX XX | *OFF | NO ATTRACT SOUNDS | |||
| XX | XX | XX | XX | ON | ATTRACT SOUNDS |
AL
| 2. | 2 | 3 | 4 | 5 | 6 | 2 | 8 |
| OFF OFF | XX | XX | XX | XX RX | 1 COIN/1 PLAY | ||
| OFF ON | XX | XX | XX | XX | XX | 1 COIN/2 PLAYS | |
| ON OFF | XX | XX | XX | XX XX | 2 COINS/1 PLAY | ||
| ON ON | XX XX | XX | XX XX | FREE PLAY | |||
| *OFF XX | KX | XX | XX XX | 1 or 2 PLAYER/CREDIT | |||
| ON | XX | XX | XX | XX XX | 1 PLAYER/CREDIT |
- = RECOMMENDED SETTINGS
he
OFF *OFF OFF OFF
*ON ON ON
Im
OFF OFF ON on In
OFF
OFF ON OFF ON OFF ON
OFF ON OFF ON Jw
OFF OFF ON ON OFF OFF
ON
*OFF ON le
XX XX XX XX
XX XX XX XX XX
irs
XX XX XX XX XX XX [ow
XX XX XX XX XX
XX XX XX XX
jon
XX XX XX XX XX XX Option Switch Settings
Io
XX XX XX XX XX
XX xX XX XX
lov
XX XX XX XX XX XX GOALIE GHOST
Gl
cA
XX XX XX XX XX XX Xx XX XX XX
Hl lo
OFF ON
leo
XX XX XX KX XX XX TIME TIME TIME TIME GAME GAME GAME GAME
- 2:30
- 2:00
- 1:30
- 1:15 21 POINT GAME 15 POINT GAME 11 POINT GAME 9 POINT GAME NO ATTRACT SOUNDS ATTRACT SOUNDS
1 COIN/1 PLAY 1 COIN/2 PLAYS 2 COINS/1 PLAY PREE PLAY 1 or 2 PLYR/CRDT 1 PLAYER/CREDIT
- = RECOMMENDED SETTINGS
SNACKS'N JAXSON Option Switch Settings
Gl
| 2 | 2 | 3 | 4 | 5 | 6 | 2 | 8 |
| OFF OFF | XX XX | XX | BONUS AT 30,000 | ||||
| ON OFF | Xx XX | XxX | BONUS AT 25,000 | ||||
| “OFF ON | XX | XX | XX | BONUS AT 20,000 | |||
| ON ON | XX | XX | XX | BONUS AT 15,000 | |||
| OFF OFF xX | XX | XX | 5 NOSES | ||||
| ON | OFF XX | XX XX | 4 NOSES | ||||
| *OFF ON | XX | XK | XX | 3 NOSES | |||
| ON | ON | XX KX | XX | 2 NOSES | |||
| XX | XX | XX OFF | NO ATTRACT SOUNDS | ||||
| XX | XX | XX | *ON | ATTRACT SOUNDS |
Al
| a | 2 | 3 | 4 | 8 | 6 | 2 | 8 |
| OFF OFF KX | KK | KX | KX | XX | 1 COIN/1 PLAY | ||
| OFF ON XX | KX | XX XX AX | 1 COIN/2 PLAYS | ||||
| ON OFF XX | XX | XX | XX XX | 2 COINS/1 PLAY | |||
| ON ON XX | XX | XX | XX XX | FREE PLAY | |||
| XX | XX XX | *ON | KEEP ALL HIGH SCORES | ||||
| XX | XX XX | OFF | KEEP 5 HIGH SCORES |
- = RECOMMENDED SETTINGS
CHICKEN SHIFT Option Switch Settings
Gl
2 2 3 4 S$ 6 2 8
XX XX OFF XX XX XX XX 3 LIVES XX XX *ON XX XX XX XX 2 LIVES XX XX XX XX XX XX OFF NO ATTRACT SOUNDS XX XX XX XX XX XX ON ATTRACT SOUNDS
Al
2 2 3 4 5 6 7 8
OFF OFF XX XX XX XX XX XX 1 COIN/1 PLAY OFF ON XX XX XX XX XX XX 1 COIN/2 PLAYS ON OFF XX XX XX XX XX XX 2 COINS/1 PLAY ON ON XX XX XX XX XX XX FREE PLAY
- = RECOMMENDED SETTINGS
TRIVIAL PURSUIT Option Switch Settings
Gl
| 2 | 2 | 3 | 4 | $8 | 6 | 2 | 8 |
| XX XX OFF OFF XX KX | XX | 6 MISSES | |||||
| XX | XX ON | OFF XX | XX | XX | 5 MISSES | ||
| XX | XX | OFF ON | XX | XX | XX | 4 MISSES | |
| XX | XX | *ON ON | XX | XX XX | 3 MISSES | ||
| XX | XX | XX | XX XX | OFF | NO ATTRACT SOUNDS | ||
| XX | XX | XX | XX XX | ON | ATTRACT SOUNDS |
HL
| ao | 2 | 3 | 4 | 58 | 6 | 2 | 8 |
| OFF OFF XX | XX | XX | 1 COIN/1 PLAY | ||||
| OFF ON | XX | XX | XX | 1 COIN/2 PLAYS | |||
| ON | OFF XX | XX | XX | 2 COINS/1 PLAY | |||
| ON | ON XX | XX | XX | FREE PLAY | |||
| XX | XX | XX | OFF | DISABLE SND DWNTD | |||
| KX | XX | XX | *ON | ENABLE SND DWNTD | |||
| XX | XX | XK | OFF | DISABLE SOUND TEST | |||
| XX | XX | XX | *ON | ENABLE SOUND TEST | |||
| XX | XX | XX | *OFF | KEEP 10 HIGH SCORES | |||
| XX | XX | XX | ON | KEEP 5 HIGH SCORES |
- = RECOMMENDED SETTINGS
xX XX
Ie
*OFF OFF ON ON 2 3
XX XX
2 3
“OFF XX ON XX OFF XX ON XxX Le
te
XX XX XX XX
* Part No.
XX XX xX XX Ia
XX XX XX XX
In STOCKER M051-00B96-A007 Option Switch Settings
Al
INDICATED FACTORY 7 8
*OFF 6 NORMAL GAME ENDING ON 3 TICKETS PER GAME OFF NO MUSIC IN ATTRACT MODE ON MUSIC IN ATTRACT MODE
7 8
1 COIN/ 1 CREDIT 1 COIN/ 2 CREDITS 2 COINS/ 1 CREDIT FREE PLAY
RECOMMENDED SETTINGS
OFF THE WALL Option Switch Settings
Gl
L 2 3 4 5S 6 2 8
XX XX XX XX XxX XX XX OFF NO ATTRACT SOUNDS XX XX XX XX XX XX XX *ON ATTRACT SOUNDS
Hl
2 2 3 4 8S 6 2 8
OFF OFF XX XX XX XX XX 1 COIN/1 PLAY OFF ON XX XX XX XX XX 1 COIN/2 PLAYS ON OFF XX XX XX XX XX 2 COINS/1 PLAY ON ON XX XX XX KX XX FREE PLAY *OFF XX XX XX XX XX l or 2 PLYR/CRDT ON XX XX XX XX XX 1 PLAYER/CREDIT
- = RECOMMENDED SETTINGS
XX XX XX XX
In
ON OFF ON OFF OFF OFF fw
XX XX XX KX
lw
ON OFF ON OFF ON OFF ON OFF ie
XX XX XX XX
Ie
ON ON OFF OFF ON ON OFF OFF to
KX XX XX XX
lw
ON ON ON ON OFF OFF OFF OFF Part No.
In
XX XX XX XX
lo
ON OFF STOCKER 020-8013-01~0A Option Switch Settings
Gl
In
OFF ON
Hl
In
ON OFF ON OFF lo
OFF ON
lo
ON ON OFF OFF NORMAL 3 TICKETS ENDS GAME NO ATTRACT MUSIC MUSIC IN ATTRACT
FREE PLAY 1 COIN/ 1 CREDIT 1 COIN/ 2 CREDITS 2 COINS/ 1 CREDIT NO BONUS COINS UU RwWH COINS ADDS 1 COINS ADDS 1 COINS ADDS 1 COINS ADDS 2 COINS ADDS 1 COINS ADDS 2 COINS ADDS 3 LEFT COIN MECH LEFT COIN MECH RIGHT RIGHT RIGHT RIGHT
- = RECOMMENDED SETTINGS COIN MECH COIN MECH COIN MECH COIN MECH BONUS BONUS BONUS BONUS BONUS BONUS BONUS x1 xX 2 De PS DE Oe coOIN COIN COIN COINS COIN COINS COINS
ll. CONTROL PANEL WIRING
GAME: SENTE 'HAT TRICK' (COCKTAIL)
SUBJECT: CONTROL PANEL WIRE SEQUENCE
BLUE PLAYER SIDE (1st Player) RED PLAYER SIDE (2nd Player)
P2 CONNECTOR P2 CONNECTOR
PIN NUMBERS FUNCTION PIN NUMBERS FUNCTION
| L | Common Display Lamps | 1 | Common Display Lamps |
| 2 | +12VDC Display Lamps | 2 | +12VDC Display Lamps |
pis Bis
| 1 | Blue Player Left (1 Player) | 1 |
2 2
| 3 | Blue Player Right | 3 |
| 4 | Blue Player Up | 4 |
5 5
| 6 | Blue Player Down | 6 |
| 7 | 2 Player Start | 7 |
| 8 | 1 Player Start | 8 |
| 9 | 9 | Red Player Right |
| 10 | 10 | Red Player Left |
| 11 | 1 Player LED | il |
| 12 | 2 Player LED | 12 |
220 220
| 1 | +5VvDC LED | 1 | |
| 2 | Common Ground | 2 | Common Ground |
3 3 4 4 5 5 6 6 7 7 8 8
| 9 | Blue Player Shoot | 9 |
| 10 | 10 | Red Player Shoot |
ll 11
| 12 | 12 | Red Player Up |
| 13 | 13 | Red Player Down |
14 14 15 15
Display lamps GE194 +12VDC.
GAME: SENTE ‘TRIVIAL PURSUIT! (COCKTAIL)
SUBJECT: CONTROL PANEL WIRE SEQUENCE 1 & 3 PLAYER SIDE 2 & 4 PLAYER SIDE
P2 CONNECTOR ; P2 CONNECTOR
PIN NUMBERS FUNCTION PIN NUMBERS FUNCTION
1 Common Display Lamps Common Display & Incorrect/Correct Lamps 2 +12VDC Display Lamps +12VDC Display & Incorrect/Correct Lamps
P15
+5VDC 1, 2, 3&4 Player Common Incorrect/Correct Switches
4 Player LED
Incorrect Button Switch (Left Side) Correct Button Switch (Right Side) °
ncorrect/Correct Button Lamps Pepe Ke URONEFOWVDIAUEWNE |S vr
1 Player Start 2 Player Start 3 Player Start 4 Player Start Be sg NVEPOCWDIDRUNAWNEH | OCODIYHMBWNE
1 Player LED L 2 Player LED
P20
2 Common Panel Switches 3:
5 Common Incorrect/Correct Lamps
12 Incorrect Button Switch (Left Side) 13 Correct Button Switch (Right Side) 14 3 Player LED
GAME: SENTE 'TRIVIAL PURSUIT’ (UPRIGHT) SUBJECT: CONTROL PANEL WIRE SEQUENCE
P15 CONNECTOR —PIN NUMBERS _ EUNCTION
1 +5vpDC 1, 2, 3&4 Player
7 4 Player LED 8 Incorrect Buttom Lamp (Left Side) 9 Correct Button Lamp (Right Side)
B16
7 1 Player Start 8 2 Player Start 9 3 Player Start 10 4 Player Start 11 1 Player LED 12 2 Player LED
P20 CONNECTOR FUNCTION
Ground Players Start Buttons
+12VDC Incorrect/Correct Lamps
Incorrect Button Switch Correct Button Switch 3 Player LED E
i<dintedaa— UBWNHRPOWDIDUBRWNE :
Resistors to each LED are 150 OHMS 1/4 Watt.
GAME: SENTE ‘OFF THE WALL'
SUBJECT: OONTROL PANEL WIRE SDQUENCE
P15 CONNECTOR PIN NUMBERS,
sl
e Sonu gH RWNHe |e WDIKRTIRWOe
wae Re FUNCTION
+5VDC LED Trackball PC AN 4 Left Player -12vDC Trackball (Knob) PC Trackball PC AN 5 Left Player Trackball PC AN 6 Left Player Trackball PC AN 7 Left Player
Right Player Left Common Ground Right Player Right Left Player Left +12VDC Trackball (Knob) PC Left Player Right 1 Player Start 2 Player Start
1 Player LED 2 Player LED
GAME: SENTE 'HAT TRICK' (UPRIGHT)
SUBJECT: CONTROL PANEL WIRE SEQUENCE
P16 CONNECTOR PIN NUMBERS
ODIDPRWNHE
be OCVBIATAWNE ran ane Pee URW FUNCTION EYRE Blue Player Up (Left Side)
Blue Player Down Blue Player Right
Blue Player Left 1 Player Start 2 Player Start Red Player Up (Right Side) Red Player Down 1 Player LED 2 Player LED
+5VDC LED Common Ground
Red Player Shoot
Blue Player Shoot Red Player Right Red Player Left
GAME: SENTE 'GOALIE GHOST’
SUBJECT: CONTROL PANEL WIRE SEQUENCE
P15 CONNECTOR __PIN NUMBERS _ WMIKHaRWNe
acl acy Ov
Ree NEPOWDUDN®WNe
P20 CONNECTOR PIN NUMBERS
ran OWnyAuaWwnNe be ary RPeeE Ue Wh FUNCTION
Trackball PC AN 4 Lower Player
Trackball PC AN 5 Lower Player Trackball PC AN 6 Lower Player Trackball PC AN 7 Lower Player
1 Player Start 2 Player Start Jump Button Lower Player #1 Jump Button Lower Player #2 1 Player LED 2 Player LED
FUNCTION
+5VDC LED Cammon Ground -l2vpCe Trackball PC Trackball PC AN 0 Upper Player +12VDC Trackball PC Trackball PC AN 1 Upper Player Trackball PC AN 2 Upper Player Trackball PC AN 3 Upper Player Jump Button Upper Player #1 Jump Button Upper Player #2
GAME: SENTE 'STOCKER'
SUBJECT: CONTROL PANEL WIRE SEQUENCE
P15 CONNECTOR PIN NUMBERS FUNCTION
+5VDC LED
—l2vpC Trackball Pc (Steering)
Trackball PC AN 6
Trackball PC AN 7
Common Ground
+12VDC Trackball PC (Steezing)
Player Start Shift High Switch
Player LED avers ro NPrPOWMYTHNUBWNHe nD ODBIMBDUIAWN-H
GAME: SENTE 'SNAKE PIT'
SUBJECT: CONTROL PANEL WIRE SEQUENCE
P15 CONNECTOR PIN NUMBERS.
ere i NF OWDIADUSWNre Ig ODBINKDGISwnye FUNCTION
+5VDC LED Trackball PC AN 4 -12VDC Trackball Pc Trackball PC AN 5 Trackball PC AN 6 Trackball PC AN 7 Alaron Button Lamp
Player Whip Up Common Ground Player Whip Down Player Whip Right. : +12VDC Trackball Pc & Lamp Player Whip Left 1 Player Start 2 Player Start Alaron Button Switch
1 Player LED 2 Player LED
GAME:
SUBJECT: SENTE ‘SNACKS 'N JAXSON’
CONTROL PANEL WIRE SEQUENCE
P15 CONNECTOR PIN NUMBERS
ODIBRUGIAWNH
ro je
Bee NEFPOODIYHRUBWNE | FUNCTION +5VDC LED Trackball PC Analog 4 -12vDC Trackball Pc Trackball PC Analog 5 Trackball PC Analog 6 Trackball PC Analog 7
Common Ground
+12VDC Trackball PC
1 Player Start 2 Player Start Sneeze Button Switch Sneeze Button Switch 1 Player LED 2 Player LED
GAME: SENTE 'CHICKEN SHIFT!
SUBJECT: OONTROL PANEL WIRE SEQUENCE
P15 CONNECTOR PIN NUMBERS FUNCTION 1 +5VDC LED
7 Red & Blue Things Button
P16 1 Blue Things Switch (Left Side) 2 Common Ground 3 Red Things Switch (Right Side)
5 +12VDC Red & Blue Things Button
7 1 Player Start 8 2 Player Start
11 1 Player LED 12 2 Player LED
DATE: July 17, 1985
GAME: Sente "GIMMIE A BREAK"
SUBJECT: Control Panel Wire Sequence
P16 CONNECTOR PIN NUMBERS FUNCTION
2 Ground (Switches)
5 +12VDC Position Cue Ball Lamp
7 1 Player Start (Straight Pool) 8 2 Player Start (Eight Ball)
10 Position Cue Ball Switch 11 Player 1 LED 12 Player 2 LED
P20
1 +5VDC (LED's) 2 Ground (Track Ball PL) 3 -12vDC 4 Track Ball PC (AN 0) 5 +12VDC 6 Track Ball PC (AN 1) 7 Track Ball PC (AN 2) 8 Track Ball PC (AN 3)
il
14 Position Cue Ball Lamp
Greg McKay Field Service Tech
GM/d1m
Ill. SCHEMATICS
RW THEO ROIS SHT BTS Maoineg SHT I Zonk Ge tC?
16 32 64 128 Le L
SMHz
[e] vsmvc re [FE] usvwe SS BLANK (Soa 8D pt 4 12 ae 3 4 Mio 3ev—do2 Br Po 4c MO5I-O00C52-COl4 Wed ——K tsoo “MATERIAL 402 fen a}? By >® MPICCLK
H BLANK 0 ap Rome 3 3 } ie MP BLANK S BLANK £0 "PCB SCHEMATIC, CPU, SAC -I
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
frifaey| score [sermons ocurron Powe] ll
ss $s 8 ss S$ 8S Leee beLEL 6123 4567
| 4 18 |i li7 | 3 {7 |13 [8 | 15 |
D a 1 11. 7 WELANK BLANK E LS374 cK HBLANK
~ Qa
| Ss 79 TS fié | eye fie Ti9 | F E |
t + ct ty a
+ +—+
+ re
¢ ie
+
14D
- 2 MBLANK 20-6 + 14 pis*— pess*—4716-\ MBLANKY—4
-——<—
| ois —S | Us | Afr | ai} —pis* |
| pess—\p | alé | Spz | ap |
| wp 8C iz | oy | gel | . |
MBLANK D3, ‘ Qe Dess werann —! 1 10. pg 1 ae Dess* 34 2 _ CONPBLANK * 5 a3}! meLank®
| COMPBLANR —* | i | a3} — MBLANK * |
cal! —narane® swtz*—erk smuz*&—Veux ays 2G Keir pG—deir MO5!-00C52-C014 Rit Ril IMMATERIAL,
ry PCB SCHEMATIC, CPU, SAC -I || G08: 8001-01-0C
cc Tvmore oBcurton [ors [orem
@owv Gals ——O!S \ses> 64m GAI4 O14 3e- 128MH se | 3 semv } CAL—O “tS. 08a Gal -O'7 20K remy 3¢MH Gale Oe
sz
SLI
sip
MPICCLK:
MO51-00C52-COl4
MATERIAL, 24Q— G03 22O— ene
2O— Got
28O— coe
WECARK ™ PCB SCHEMATIC,
CPU, SAC-I
| G08-so01-o1-0c [Et
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
BAD
BAB
BAT
BAG
BAS
BAe
BAS
bag far] scone | _nevsenssescurroy Taare
ALL RESISTORS 2.2K IN Ib PIN DIP EXCEPT WHERE NOTED 3 Rea Peele giz 45 q 2 i RPS RPA 2N3904 4 +5
ue Lsegs a{2 BI q 116 a" “62 a “6s "*or_so $0_Si os? 58] usi7s rr is an PP cs rae: es i ie, 108 \ BoM 8D BOe BDS BOs vee ’) a) nt P LE)
=~
T ComP dcr BLANK on
WBE a u
Lgeae ry > m le
1 Lseee
30D. ae. “eT
MATERIAL
mm PCB SCHEMATIC,
CPU, SAC-I
'p|d08-8001-01-0c_ [el sour NONE wueer 9 Hl
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
see oem AV
SEE DETAIL B
NOTES: UNLESS OTHERWISE SPECIFIED [1] v1 TEM 90) TO HAVE 20 AWG WIRE WRAPPED AROUND BODY AND SOLDERED IN HOLES PROVIDED. SCALE:2/1
MOSI-00C52-COl13
PCB ASSEMBLY, CPU PCB ASSEMBLY, CPU (006-8001-10-0C) (M051-00C52-C013) (006-8001-10-0C) (M051-00C52-C013) PARTS LIST - SHEET 2 of 4 PARTS LIST - SHEET 3 of 4
| Orr. | PART NO. | REFERENCE | DESCRIPTION | a | Trem | TY. | PART NO. | REFERENCE | DESCRIPTICN |
| L | 1 | 007-8001-01-0C | PCB, FABRICATION, CPU,SAC-1 | 44 | 3 | 240-0003-01 | UL8F,17F,16F | IC,DIG,RAM,2148,1K X 4,70NS | |
| 2 | 45 | 32 | 240-0004-01 | U1A-BA, 1B-8B, | IC, DIG, RAM, 4116, 16K X 1,150NS | ||||
| 3 | 3 | 200-0039-01 | UllF,14D,14C | IC, DIG, TTL, 74LS00,NAND GATE | 1C-8C,1D-8D | ||||
| é | 2 | 200-0040-01 | U14E,15B | IC, DIG, TTL, 74LS02,NOR GATE | 46 | 1 | 260-0002-01 | UsH | IC, DIG, INT, ULN2003, DRIVER |
| 5 | 1 | 200-0041-01 | u16C | IC,DIG,TIL,74LS04,HEX INVERTER | 47 | 1 | 015-8001-10-0B = U20F | PAL, SAC-1 | |
| 6 | 1 | 200-0042-01 | U13E | IC, DIG, TTL, 74LS20,4-IN NAND | 48 | 1 | 250-0010-01 | U9G | IC,DIG,MPS, 68B50,ACIA, ..75MHZ |
| 7 | 3 | 200-0043-01 | U8F,9F,14B | IC, DIG, TTL, 74LS32,OR GATE | 49 | 1 | 250-0006-01 | ul7c | IC, DIG MPU, 68A09E |
| 1 | 200-0044-01 | U17B | IC,DIG, TTL, 74LS74,DUAL D F/F | 50 | 1 | 260-0030-01 | L6G | IC,SP,,ADC 8 BIT,ADCO809 | |
| 1 | 200-0075-01 | ULOH | IC, DIG, TTL, 74LS86,QUAD X-OR | 51 | 1 | 320-0006-01 | C157 | CAP, MIC, RAD, 12PF ,500V,5% | |
| l | 200-0045-01 | ul6D | IC,DIG, TTL, 74L$96,5 BIT SHIFT | 52 | 1 | 320-0007-01 | C158 | CAP, MIC,RAD, 100PF ,500V, 5% | |
| i | 2 | 200-0046-01 | U13F,14F | IC,DIG, TTL, 7415109, DUAL JK F/F | 53 | 172 | 300-0009-01 | C1,3,5,7/9,11,13, CAP,;CER,AXL, 0.JUF,50V, 20% | |
| 12 | 1 | 200-0047-01 | ULF | IC, DIG, TTL, 74LS125,QUAD BUFFER | 15,17-95,97,98, | ||||
| 13 | 2 | 200-0048-01 | U17D,U20E | IC, DIG, TTL, 74LS138,3-8 DECODER | 100,102,103,105, |
Mw 106,108,109,111, 15 112,114,115,117,
| 16 | 2 | 200-0052-01 | U12C,13C | IC,DIG, TTL, 74LS163,4 BIT COUNT | 118,120,121-156, | ||||
| 17 | 1 | 200-0076-01 | Ul1H | IC,DIG,TT.,74LS164,8 BIT SHIFT | 159-185,190-195 | ||||
| 18 | 5 | 200-0053-01 | U10B,11B,15C,17G, IC,DIG,TTL,74LS174,HEX D F/F | 54 | 2 | 340-0015-01 | C96, 186 | CAP, ELEC, AXL, 1.0UF,63V,50/~10% | |
| 18G | 55 | 2 | 340-0011-01 | C187,C188 | CAP, ELEC ,AXL, LOQUF,16V,50/-10% | ||||
| 19 | 3 | 200-0032-01 | U19A,15D,19E | IC, DIG, TTL, 74LS175,QUAD D F/F | 56 | 1 | 340-0018-01 | c189 | CAP, ELEC, AXL, 470UF ,6.3V,50/ |
| 20 | 7 | 200-0055-01 | U18B,20B,12E,18E, IC,DIG,TTL,74LS244,8TS BUFFER | ~108 | |||||
| 17E,16E, 15F | 57 | 8 | 310-0013-01 | C2,6,10,14,101, | CAP,TAN,AXL,2.2UF,10V, 20% | |||||
| iL | 200-0056-01 | U19B | IC,DIG,TTL, 74L8245,8 BUS XCVR | 107,113,119 | |||||
| 6 | 200-0057-01 | U11D,11C,26,36, | IC,DIG, TTL, 74LS253,DATA SELECT | 58 | 8 | 310-0014-01 | C4,8,12,16,99, | CAP, TAN ,AXL, 4. 7UF, 20V, 20% |
46,56 104,110,116
| 23 | 1 | 200-0078-01 | UL2A | IC,DIG, TTL, 74LS257,4 2-1 MUX | 59 | 4 | 460-0015-01 | RP11,RP13,RP15, | RES,PAK,SIP,8 PIN,4X,33 OHM | |
| 24 | 1 | 200-0058-01 | U9H | IC, DIG, TTL, 74LS259,8 BIT LATCH | RP16 | ||||
| 25 | 1 | 200-0059-01 | Ulla | IC, DIG, TTL, 74LS273,OCTAL D F/F | 60 | 2 | 460-0016-01 | RP12,RP14 | RES ,PAK,SIP,10 PIN,5X,33 OHM |
| 26 | i | 200-0077-01 | ullG | IC,DIG,TIL,74LS299,8 BIT SHIFT | 61 | ||||
| 27 | 5 | 200-0060-01 | U10C,10D,9D,9C, | IC, DIG, TTL, 74LS374,OCTAL D F/F | 62 | 1 | 400-1500-01 | R63 | RES ,CF,1/4W,5%,150 OHM |
| 1lE | 63 | 1 | 400-2200-01 | R29 | RES ,CF,1/4W,5%,220 OHM | ||||
| Z8 | 64 | 3 | 400-4700-01 | 32-34 | RES,CF,1/4W,58,470 OHM | ||||
| 29 | 65 | 37 | 400-1001~01 | R7,8,9,11,14,15, RES,CF,1/4W,5%,1K OHM | |||||
| 30 | 2 | 200-0061-01 | UL7A,15A | IC,DIG, TTL, 74500, NAND GATE | 18-21, 27, 28,35-57 | ||||
| 31 | 1 | 200-0062-01 | U16A | IC,DIG,TIL,74S02,NOR GATE | 62,64 | ||||
| 32 | 2 | 200-0063-01 | U12G,18A | IC, DIG, TTL, 74S04,HEX INVERTER | 66 | 1 | 400-2701-01 | R12 | RES,CF,1/4W,5%,2.7K OHM |
| 35 | l | 200-0064-01 | U10F | IC,DIG, TTL, 74S08,AND GATE | 67 | 6 | 400-4701-01 | R13,31,58-61 | RES ,CF,1/4W,5%,4.7K OHM |
| 34 | 1 | 200-0065-01 | U1OE | IC,DIG, TTL, 74S32,OR GATE | 68 | 2 | 400-1002-01 | R26, 30 | RES ,CF,1/4W,5%,10K OHM |
| 35 | 200-0066-01 | U12F | IC,DIG,TTL,74S74,DUAL D F/F | 69 | 2 | 400-1003-01 | R16,17 | RES ,CF,1/4W,5%,100K OHM | |
| 36 | 200-0067-01 | U2E-6E, 1, 2F | IC,DIG, TTL, 74S151,8-1 MUX | 70 | 5 | 460-0011-01 | RP4-8 | RES,PAK,DIP,16 PIN,8X,2.2K OHM | |
| 37 | 200-0068-01 | U12B,13B,13A | IC,DIG,TTL,74S157,4 2-1 MUX | 71 | 2 | 460-0012-01 | RP9,10 | RES,PAK,SIP,10 PIN,9X,470 OHM | |
| 38 | 200-0069-01 | U3F ,4F,5F,6F,13D, IC,DIG,TTL,745163,4 BIT COUNT | 72 | L | 460-0014-01 | RP3 | RES, PAK,SIP,8 PIN,7X,1.0K OHM | ||
| 12D | 73 | 2 | 460-0013-01 | RP1,2 | RES,PAK,SIP,10 PIN,9X,10K OHM | ||||
| 3 | 3 | 200-0070-01 | U9E,14A,10A | IC,DIG, TTL, 74S174,HEX D F/F | 74 | 1 | 400-2700-01 | R1O | RES ,CF,1/4W,5%,270 OHM |
| 2 | 200-0082-01 | U20A,U16G | IC,DIG, TTL, 74S86 ,QUAD X-OR | 75 | |||||
| 4) | 76 | 1 | 510-0019-01 | U9G | SOCKET, IC, 24P, LOW PROF, PC | ||||
| £2 | l | 210-0005-01 | ulsD | IC,DIG,CMOS,4049UB,HEX INVERTER | 7 | l | 510-0020-01 | U6G | SOCKET, IC, 28P,LOW PROF, PC |
| 43 | 1 | 230-0007-01 | U1SE | IC,DIG,NOV RAM,X 2212,256 X 4 | 78 | 1 | 510-0021-01 | ul7c | SOCKET, IC, 40P, LOW PROF, PC |
PRE
NER
Peee PCB ASSEMBLY, CPU (006-8001-10-0C) (M051-00C52-C013) PARTS LIST - SHEET 4 of 4
: PART _NO.
550-0063-01 500-0016-01 100-0002-01
120-0003-01 260-0011-01
820-0004-01 840-0036-01 570-0036-01
801-0440-06-01 812-0440-00-01 822-0004-00-01 800-00237-01
200-0079-01 200-0080-01 J22 Ll CR
Q1,2,3,4 VR1
yl Dsl U1G,1H
Dsl
U7F ,U16B U7E,U9B DESCRIPTION
CONN, AMP 1-102589-7 INDUCTOR, FER ,AXL, 100UH, 10% D10,SI,10MA,75 PIV, IN914
XSTR,SI,NPN, 2N3904 1C,LIN,VR,7905,5V NEG
CRYSTAL, 20.000MHZ OPT, DSP, LED, SNG, RED SW,DIP,8 PST
SCREW PH PH 4-40 x 3/8" NUT, HEX, 4-40 WASHER, SPLIT LOCK #4 SPACER, LED
IC, DIG, TIL, 74F175,QUAD D F/F IC,DIG, TIL, 74F374,OCTAL D F/F
FIRMWARE ROM
> is} jo. comes -BUS
: = y o iw
| -_ | Al | 7 | 38 (2,08) | |
| Be | Ae | | | 8 |Send | |
| ls _ pa] | ina _s| | 10 [RES | ||
| oat | Ina] | 9 [SCOKHE | ||
| 9 | OD | AS | 3. | SERIAL T/O |
Ss tg aa a > if g
1S
R
‘DACL (2,85) DACM (2,58) SHSTR PIN (3,08) BHD PIN 9 (3,D6) ENAUD (2,88) TUNE (2,88) T REELEEEEEEEEEED
NOTES: UNLESS OTHERWISE SPECIFIED 1, ALL RESISTORS ARE IN OHMS, 4 W, 5%.
- ALL CAPACITORS ARE IN MICROFARADS , 01 / ICOV. MO51-00C52- BOI6
- LAST REFERENCE DESIGNATORS USED: A124 ,Cia8, waren 034, CR4 YI.
SCHEMATIC, AUDIO, 6VB PRAWING NO- ™ ™ ID] 008- 8002-10-08 [ay
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTES: e a pons OOD (28 }-he-fas saa e sanveuas
L— PRIOR TO MOUNTING. APPLY HEATSINK COMPOUND TO HEATSINK (ITEM 62) ¢ HEATSINK (ITEM 70)
SHORT PIN | TO PIN2 OF U Z-80A
TO WISE AMI 2688 (5837 EQuiIV) FASTEN U40 (ITEM 53) TO HEATSINK (ITEM 62)
28, AND MOUNT ©& AS SHOWN > HEAT AW «
- WITH HARDWARE (ITEM 66,67 & 68) BEFORE SOLDERING TO PCB. INK (ITEM TO) AND PCI & la (TEM ©?) i A A
C60 POLARITY OF C5. ADDED NOTE 3, REVERSED
sur 20 [| 8] i924 [ADDED 2 HEATSINKS, REVISIONS DESCRIPTION
PCB ASSEMBLY, AUDIO, 6VB
‘DRAWING NO,
wrt | ITEMS 62 £ 70] 294
MO51-00C52 - BOI ‘60 |wt4
fo iS Is} Im iS) jo 9. oa
(006~-8002-10-0B) (M051-00C52-8015) PCB ASSEMBLY, AUDIO 6VB
PARTS LIST - SHEET 2 of 4
| Trem | ory | PART NO. | REFERENCE | |
| 1 | 2 | 400-1001-01 | R1,R44 | RES ,CF,1/4W,5%,1K OHM |
| 2 | 1 | 400-6802-01 | R3 | RES ,CF,1/4W,5%,68K OHM |
| 3 | 5 | 400-1003-01 | R4,5,42,45,51 | RES,CF,1/4W,5%,100K OHM |
| 4 | 12 | 400-1004-01 | R6,7,12,13 | RES ,CF,1/4W,5%,1.0M OHM |
| 5 | 3 | 400-3300-01 | R8,9,11 | RES, CF, 1/4W,5%,330 OHM |
| 6 | 6 | 400-2001-01 | R15,16,17,20,22,50 | RES,CF,1/4W,5%,2.0K OHM |
| 7 | 3 | 400-4701-01 | R25,41,46 | RES,CF,1/4W,5%,4.7K OHM |
| 8 | 2 | 400-4702-01 | R48, 49 | RES, CF,1/4W,5%,47K OHM |
| 9 | 1 | 400-3307-01 | R43 | RES, CF,1/4W,53,33 OHM |
| 10 | 1 | 401-1005-01 | R47 | RES, CC,1/4W,5%,10M OHM |
| il | 6 | 450-3013-01 | R2,10,14,21,26,29 | RES MF, 1/8W,18,301K OHM |
| 12 | 1 | 450-1962-01 | R40 | RES ,MF,1/8W,1%,19.6K OHM |
| 14 | 1 | 450-2002-01 | R30 | RES, MF, 1/8W,1%,20.0K OHM |
| 15 | 1 | 450-4021-01 | R31 | RES ,MF,1/8W,1%,4.02K OHM |
| 16 | 1 | 450-1001-01 | R32 | RES ,MF,1/8W,1%,1.00K OHM |
| iy | 1 | 450-1210-01 | R35 | RES MP, 1/8W, 18,121 OHM |
| 18 | 1 | 450-4990-01 | R36 | RES ,MF,1/8W, 18,499 OHM |
| 19 | 1 | 450-1002-01 | R39 | RES ,MF,1/8W,1%,10.0K OHM |
| 21 | 12 | 330-0005-01 | C14,18,34,38,53, | CAP, PES, RAD, 0.001UF, |
57,71175,89, 93,119, 100V, 10%
| 22 | 6 | 330-0009-01 | C1,15,35 | CAP, PST ,AXL,0.002UF, |
54,72,90 100V,58
| 23 | 48 | 330-0006-01 | €2,5,6,7,9,16,23,25, | CAP,PES,RAD,0.01UF,100V, |
26,27,28,29,30,36,43, 10% 45,46,47,48,49,50,55, 62,64,65,66,67,68,69, 73,80,82,83,84,85,86, 87,91,98,100,101,102, 103,104, 105,126,129,
| 24 | 20 | 330-0007-01 | €20,21,22,40,41,42, | CAP, PES,RAD, 0,033UF ,100V |
59,60,61,77,78,79,95, 10% 96,97,113,114,123, 124,125
| 25 | 3 | 300-0011-01 | 112,116,134 | CAP, CER, RAD, 33PF , 50V, 10% |
| 26 | 7 | 300-0012-01 | C19,31,39,58,76,94, | CAP, CER, RAD, 680PF , 50V, 5% |
| 27 | 25 | 300-0002-01 | C3,4,10,12,17,24,32, | CAP,CER,RAD,0.1UF,50V, 208 |
37,44,51,56,63, 74,81, 92,99,106,107,109, 110,111,115,117,128,
| 28 | 3 | 310-0012-01 | €127,131,132 | CAP, TAN, RAD, 1.0UF, 25V, 208 |
| 29 | 3 | 340-0016-01 | €8,11,108 | CAP, ELC,AXL, 2.2UF ,63V,50/ |
10% Peer ob
Pee PCB ASSEMBLY, AUDIO 6VB (006-8002-10-0B) (M051-00C52-B015)
PART NO.
340-0017-01
260-0033-01
210-0007-01
210-0006-01
210-0005-01
260-0029-01
260-0031-01 260-0007-01 260-0037-01
210-0008-01
260-0040-01 200-0039-01
200-0041-01
200-0043-01 200-0044-01
200-0074-01
200~0049-01
250-0007-01
240-0005-01
250-0008-01 250-0010-01
260-0027-01
260-0028-01 260-0008-01 100-0006-01 550-0062-01
510-0019-01 510-0020-01 510-0021-01 100-0002-01 PARTS LIST —- SHEET 3 of 4
REFERENCE
C13,33,52,70,88,118
U1,6,11,16,21,31
U24,25,27,28,30
U3,7,12,17,22,32
U36
U34
U35 U37 U33
U29
U2 ul8
U8,19
ul4 U23
ud
U13
u4
ul0,15
u20 U26
U38
u40 U39 D1,2,3,4 J5
U10,15,20, 26 US u4 DS DESCRIPTION
CAP, ELC,AXL, 1OUF, 35V,50/
IC, SP,SOUND, SYNTH, CEM, 3394 IC,DIG,CMOS,41748,HEX D F/F IC,DIG,CMOS,40518,8 CHAN MUX IC,DIG,CMOS, 4049UB , HEX INVERT IC, LIN,OPAMP, TLO84,QUAD, JFET IC,SP,DAC 12 BIT, 7541 IC, LIN, COMP, LM311N IC,LIN,OPAMP,TLO?7i,JFET, INPUT IC,DIG,CMOS, 4503B,HEX TS BUFFER IC,SP,NOISE SOURCE MM5837 IC, DIG, TTL, 74LS00 , NAND GATE IC, DIG, TTL, 74LS04 , HEX INVERTER IC,DIG, TTL, 741532,OR GATE IC,DIG, TTL, 741.874, DUAL D E/F IC,DIG, TIL, 7493,4 BIT COUNT IC,DIG, TTL, 741S139,2-4 DECODER IC,DIG,MPU, 2~80A
IC,DIG, RAM, 6116, 2KX8, 200NS IC,DIG,MPS ,8253-5,TIMER IC,DIG,MPS, 68B50,ACIA ~ 7SMHZ IC, LIN, VR, 337T,, VARIABLE NEG. IC, LIN, VR, 78M05CT,5V POS IC, LIN, VR,7805,5V POS DIO,GR, 50MA, 75PIV, IN34 CONN 10 PIN LOCKING 09-74-1101 SOCKET, IC, 24P, LOW PRO SOCKET, IC, 28P, LOW PRO SOCKET, IC,40P, LOW PRO D1O,S1,10MA,75 PIV, IN914
PCB ASSEMBLY, AUDIO 6VB (006-8002-10-0B) (M051-00C52-B015) PARTS LIST - SHEET 4 of 4
| ITEM | Ory. | PART NO. |
| 61 | 1 | 820-0003-01 |
| 62 | 1 | 850-0007-01 |
| 63 | 1 | 310-0015-01 |
| 64 | 2 | 400-2703-01 |
| 65 | 1 | 400-2700-01 |
| 66 | 3 | 801-0632-06-01 |
| 67 | 3 | 822-6006-00-01 |
| 68 | 3 | 816-0632-00-01 |
| 69 | 1 | 007-8002-01-0A |
| 70 | 1 | 850-0008-01 |
REFERENCE
XTL-1 HS-1 c120
R33,34 R52
HS-2 DESCRIPTION
CRYSTAL 8.000MHZ HEATS INK, THM~6070 CAP, TANT, RAD, 47UF, 15V, 208% RES, CF,1/4W,5%,270K OHM RES ,CF,1/4W,5%,270 OHM SCREW PAN HD-PHIL 6-32X 3/8 WASHER SPLITLOCK 6 NUT,HEX,SM PAT, 6-32 PCB, FAB, AUDIO, 6VB HEATSINK, THM-6071
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
+5 +5 RIG FET SWITCH asa Los
| DB 11) CLK “A ollo | EN AYDIO | ‘ |
I7
| 2 | R33 | Cil4 | |
| W2 | ul | 270K G033 | |
| DBUS 6 | UN | -soo | 14 |
| (1.08) | Io | Ras | Doe |
OUTT ] 2l00k IN34 DIN34 D3 D4 N34 FINS4
ENNMI (ici) yea. 5)
| IN4 | ro-=1 ya | R26 | 5 |
+ i: 2k 4d A 9 16 tsp lie U30 Vdd p23} Y30 oe 5g 0314 4 gills 144,
| [os | + al | 3p |
+5
| D5 13) | a3 12 | 1a, | A |
| De 6 | aal? | uh, | Ree 7 34 |
TIME oe
| ‘ells | TSOUNTER | o7 I | 05 10 | 19], u3s JM, \% 5 AREF |
\ sD cioad R31
| as [RES | 7541 | 59S Bax 1? |
| 2 MHZIBI) | 7 a | Teav ww b dov |
al a A" MA u20g—}-— D
| PIN I8 | VREF| 7, | +4 VOLT] |
+5 A BUS 9 D ign] yt 6
| po | 10 | R40 | |||
| 45 | It Ueg aol | 36 | 19 k | ||
| De} 4 gif | 8|, | wit | |||
| ula | R50 | R23 7 allt | ‘te RFBls r | 33 | |
| PIN 35 | D3 4 | 5 | 6 | 12 | 50V |
| (,BI) | a3 | ° | pt U34 | R30 | |
| D4 14] | all | 50 ppsovl an | 200K AW. 1% | ||
| dS 3) | 2. | 4 | 2 | 3 | |
| m= 8 | " 12 G7 O70 | *5A oll | |||
| +5) [RES | GND | A 4 | U33 iM |
LL 8 wsB [5
| % | ‘i | CA |
R39 3 — * 10.0K 41 1S! sov WI -o.5v YA
| u34 BUS u24 | u25 | u3 | |
| PINI4 (3,08) PIN? | PINS | PINS | |
| (308) | (3.08) | (3,06) | (3.06) |
Figure 13 Audio Schematic, Sheet 2
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Jl Fl CA /250\ 9 i} Vv
o1 MURI6!9
Voz MURI6I0'
F4 3A/250V
Fs 3A/250V MRSOI
(MURI6IO.
eX D: MURICIO|
D6 J2
+5V +SV RIB e2 05 2N3055, SW,IO% CIA CAB cic c1iD
| +L10,000*£ 40,000 *L 10,000 *L¥0,000 | al | Buk | bis | 21 SCRI | ||
| oe ve | tev | Trev | aNsoss | wok | wary | Ri |
+Lc2
\ SOV 390 8 5 __to L ~ ul +5V
| [ial | MCI723 | & | V | 8 |
G TT RIO [|
cis S00v al Sov v, RI4 4.74 cred Sov
bea MR5OI ay ly US 5 MC7BI2 +lev
z
B v2 4 . ay
+15V
25v [ess] econ nevnons Descurow [ere [a [1984] PRODUCTION RELEASE _— B [1998 [RELEASED REDESIGNED PCB Del RI I] |
NOTES: UNLESS OTHERWISE SPECIFIED
I. ALL RESISTORS ARE IN OHMS, '/4aW,S%,
- ALL CAPACITORS ARE IN MICROFARADS.
- LAST REFERENCE DESIGNATORS USED: R25, C27, D25,U6 ,Q2,F5.JI9,SCRI.
- HEAT SINK ATTACHED TO AUDIO GROUND.
Ss. = AUDIO GND
v = GND
MO5\-00C52 - BOIS
MATERIAL,
Te SCHEMATIC, LINEAR POWER SUPPLY
DRAWING BO” 008-8009 -10-OB
REVISIONS DESCRIPTION
OUT!
OUT 2
MO51-00C52- BOIs
MATERIAL
SCHEMATIC, LINEAR POWER SUPPLY ID] (008-8009-10-CB
DETAIL C TYPICAL 4PL (DI-D4) SCALE: 2/1
G@)-
2 PL (62
NOTES: UNLESS OTHERWISE SPECIFIED 55.
- 9 PL
‘aon oC aoe eCtso3 ecpso4
ee,
cH T VIEW A-A TYPICAL 2PL (Q1,02)
- 3PL SCALE: 2/1
- 6PL
- 3PL
- 3PL
- SPL E
I APPLY HEATSINK COMPOUND (ITEM 60) ON BOTH SIDES OF INSULATOR (ITEM 78) AT Q! AND @2, AND ON BOTH SIDES OF INSULATOR (ITEM 77)AT U2 ANDU3. APPLY BETWEEN HEATSINK AND COMPONENT AT U4,US U6 ,DI,D2,D3 AND D4.
- 2PL
- 2PL
- 2PL DETAIL B TYPICAL 2PL (U2,U3) SCALE: 2/1 [evs Jorsora] Leet EA
MO51-00C52- BOI7
IMATERIAL
PCB ASSY, LINEAR POWER SUPPLY
DRAWING NO- REV | 06 - 8009-10-0B
PCB ASSEMBLY, LINEAR POWER SUPPLY (006-8002-10-0B) (M0S1-00C52-8017) PARTS LIST — SHEET 2 of 3
| ITEM | ory. | PART _NO. | REFERENCE |
| 1 | 1 | 001-8076-01-0B | |
| 3 | 1 | 007-8009-10-0B | |
| 5 | 20 | 100-0008-01 | D5-D18, D20-D25 |
| 7 | 4 | 105-0004-01 | D1-D4 |
| 8 | 1 | 110-0004-01 | Dlg |
| 10 | 2 | 120-0004-01 | 01,02 |
| 12 | 1 | 160-0004-01 | SCR1 |
| 14 | 2 | 260-0039-01 | U4,U6 |
| 15 | 1 | 260-0042-01 | U2 |
| 16 | 1 | 260-0043-01 | U3 |
| 17 | 1 | 260-0044-01 | US |
| 18 | 1 | 260-0045-01 | Ul |
| 20 | 9 | 300-0002-01 | C6,C7,C12,C13,C15,C17, |
C20,C23,C25
| 21 | 2 | 300-0001-01 | C24,C26 |
| 22 | 1 | 320-0007-01 | co |
| 24 | 4 | 340-0026-01 | C14,C16,C18,C22 |
| 25 | 2 | 340-0027-01 | c19,C21 |
| 26 | 4 | 340-0028-01 | C1A,C1B,C1C,C1D |
| 27 | 4 | 340-0029-01 | C3,C4,C10,C1L |
| 28 | 4 | 340-0030-01 | C2,C5,C8,C27 |
| 30 | 2 | 400-1000-01 | R8,R16 |
| 31 | 2 | 400-1008-01 | R1,R2 |
| 33 | 2 | 400-1007-01 | R7,R11 |
| 35 | 1 | 400-1501-01 | R13,R10 |
| 37 | 1 | 400-2200-01 | R15 |
DESCRIPTION
HEATSINK, E-368/#5555
PCB FAB, LINEAR PWR SPLY
D10,SI,3A,100 PIV,MR501
D10,RECTIFIER, 16A, MUR1610 CT D10,ZEN,5.6V,20MA, IN752A
XSTR,SI,NPN, 2N3055
SCR, 8A, 50V,C122F1
IC, LIN, SP, TDA2002,AUD AMP IC, LIN, VR/MC7912,-12V, 3 Pos IC, LIN, VR,MC7812,+12V, 3 POS IC, LIN, VR,MC7815,+15V, 3 POS IC, LIN, VR,MC1723, SI ,MONO
CAP,CER, RAD, .1MF ,50V CAP, CER, RAD, .022UF, 50V, CAP, MIC, RAD, 100PF ,500V,
CAP, ELC,RAD, 10MF, 50V, 208 CAP, ELC,RAD, 470MF ,16V, -10%,+50% CAP, ELC, RAD, 10.000MF,16V +10%,-308 CAP, ELC,RAD, 6800MF ,, 25V, -10%,+30% CAP, ELC, RAD, 1000MF,50V, 20%
RES,CF,1/4W,5%,100 OHM RES ,CF,1/4W,5%,1 OHM RES CF, 1/4W,5%,10 OHM RES ,CF,1/4W,5%,1.5K OHM
RES ,CF,1/4W,5%,220 OHM PCB ASSEMBLY, LINEAR POWER SUPPLY (006-8009-10-0B) (M051-00C52-B017) PARTS LIST - SHEET 3 of 3
| TIEN | OT. | PART NO. | REFERENCE | DESCRIPTION |
| 38 | 2 | 400-2208-01 | R19,R23 | RES, CF,1/4W,5%,2.2 OHM |
| 40 | 1 | 400-2701-01 | R17 | RES, CF,1/4W,5%,2.7K OHM |
| 41 | 1 | 400-3900-01 | RQ | RES, CF, 1/4W,5%, 390 OHM |
| 42 | 2 | 400-4701-01 | R6,R14 | RES,CF,1/4W,58,4.7K OHM |
| 43 | 2 | 400-4707-01 | R21, R25 | RES, CF, 1/4W,58,47 OHM |
| 44 | 1 | 480-0007-01 | R12 | RES, VAR, STR, TRIM, 1K OHM |
| 45 | 1 | 480-0008-01 | R4 | RES, VAR, STR, TRIM, 100 OHM |
| 46 | 3 | 410-2200-01 | R20,22,24 | RES, CF, 1/2W,5%,220 OHM |
| 47 | 1 | 440-0508-01 | R18 | RES, WW, 5W, 108, .05 OHM |
| 50 | 1 | 550-0067-01 | 33 | CONN, PC, 4P,M, 09-74-1041 |
| 51 | 1 | 550-0068-01 | 4 | CONN, PC, 5P,M, 22-23-2051 |
| 53 | 1 | 550-0102-01 | J2 | CONN, PC, 11P,M,09-74-1111 |
| 54 | 1 | 550-0103-01 | g19 | CONN, PC, 11P,M,10-19-1111 |
| 55 | 1 | 550~0110-01 | Jl | CONN, PC, 9P, PLG, 19-09-2099 |
| 56 | 9 | 550-0111-01 | Jl | CONN, PIN,M, PC, 02-09-8113 |
| 58 | 10 | 580-0070-01 | F1-F5 | FUSE, CLIP, PC, 1/4" |
| 60 | WR | 790-0007-01 | THERMAL JOINT COMPOUND | |
| 62 | 13 | 800-0240-01 | BUSHING, INSULATED, NYLON | |
| 63 | 10 | 800-0241-01 | U2-U6 | WSHR, RECTANGULAR, METAL, #6 |
| 65 | 4 | 801-0440-04-01 | D1-D4 | SCREW, PH,PH,4-40 X 1/4" |
| 67 | 6 | 801-0632-08-01 | 91,02 | SCREW, PH, PH, 6-32 X 1/2" |
| 68 | 5 | 801-0632-10-01 | U2-U6 | SCREW, PH, PH, 6-32 X 5/8" |
| 70 | 4 | 812-0440-00-01 | D1-D4 | NUT, HEX, 4-40 |
| n | ul | 813-0632-00-01 | NUT, HEX, KEP, 6-32 |
2B
| 4 | 4 | 830-0019-01 | F2-F5 | FUSE, 3AG, 3A, 250V, FAST |
ACTING
| 75 | 1 | 830-0020-01 | Fl | FUSE, 3AB, 10A, 250V, SLO-BLO |
| 77 | 2 | 850-0009-01 | U2,U3 | INSULATOR, MICA , TO-220 |
| 73 | 2 | 850-0010-01 | 1,02 | INSULATOR, MICA, TO-3 |
| 79 | 4 | 850-0011-01 | D1-p4 | HEATSINK,PC MOUNT, VERT, |
TO-220
JI7 Ji2
J13
NOTES: UNLESS OTHERWISE SPECIFIED
- A, PINS 143-AC POWER B. PIN 2-CHASSIS GROUND
M05 1-00C47-A016
Bory SCHEMATIC, AC SENSE
}E|o08-2o06-or-08 || [cae NONE weer
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
PCB ASSEMBLY, AC SENSE (006-8006- 10-0B) (M051-00C47-A015) PARTS LIST (Page 2 of 2)
| : | a r 9 | (TEM | TY. | PART_NO. | REFERENCE | DESCRIPTION _ | |
| < | = | o | |||||
| n | aed ZI | 1 | 1 | 007-8006-01-08 | PCB FAB, AC SENSE | ||
| ° | a | |,0 | 2 | ||||
| s | oY fy | 3 | 6 | 550-0018-01 | CONN,PC,F,PINS,MLX 02-09-1134 | ||
| i | 4 | Hs | 4 | 2 | 550-0069-01 | J12,513 | CONN, PC, 3P,F,MLX 03-09-1031 |
| 2 | 5 | 1 | 550-0087-01 | JIT | CONN,PC,3P,M,MLX 09-75-1038 |
g fo) =
je
e H
NOTES: UNLESS OTHERWISE SPECIFIED
Trackball Interface Board
- dub CAPACITORS ARE WW MUCRORARADS, O.1/ SOV. sey
- ALL MESSTORS ARE IN UMS. Yb Ws 5 le
- LAST REFERENCE CESGNATOR USED: 2 Rio, c@,cRe,U3, 92. iow J ce
swe]
IV. MONITOR
PLEASE NOTE:
THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.
IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.
OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!
THANK YOU
Introduction: (How to
use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the ‘T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!
If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. if you wish, you can follow along with the schematics. The information is presented in a very basic manner but a more complete treatment of the subject can be found in the technical sections of bookstores
'f you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings
T.V. Monitor Manua!
and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:
- Find the symptom that matches the problems. your monitor has in the “SYMPTOM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
- Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
- Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS" subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is ali there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Bally Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)
s
Symptom Diagnosis
- Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). O Bad yoke. C] Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. O Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke, O Open width coil. 0 Open part in horizontal output section.
- Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad Component in output circuitry. C. Vertical linearity or damper control needs adjustment.
- Line too close with black spacing: A. Problem in vertical section causing poor linearity.
- Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.
- Colors missing; check: Interface color transistors. Color output transistors. Cracked printed circuit board (neck Board). Color circuits. Video input jack. . Defective picture tube.
- Picture not bright enough: A. Weak emission from picture tube.
- Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission.
- Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high.
- Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit). B. Bad component in monitor's power supply. ™MOOQOD> 10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator in the IC, vertical sync. transistor, or circuit. B. No sync from logic board. C. Three pin sync. jack is loose or plugged in wrong. Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference. Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke. No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit). No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias. No high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moog>
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture syrnptom).
Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.
- Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
- Can't sdjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. B. Picture tube defective. C. Nearby equipment is electromagnetically interferring. D, The poles of the earth are puiling off the purity — see “A” above. E. Poor focus or width of picture. Make sure you have the correct CAT number for that brand of monitor. m
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN’T MATTER)
SYTNW
INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
OL
FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
couecror-7> COLLECTOR a BASE ——— BASE
EMITTER lS EMITTER TE
NPN TRANSISTOR PNP TRANSISTOR
' WA —
VARIABLE RESISTOR, POT, CONTROL RESISTOR
(POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)
+ =
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)
tha & GROUND
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits).
- Fusible resistors.
- Electrolytic capacitors.
- Resistors.
- Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 23,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors) or ICs, yoke terminals, and other high power components when the monitor is on.
Observe the picture carefully. Try to vary the appropriate contro! that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hoid a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the onmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and ashort is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some componentis messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand whai goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.
THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn't mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Eiectrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its sync section. The Zenith monitor (CD19MXRFO6) also uses an IC. for the sync processing. Wells Gardner uses HA11423, Electrohome uses HA11244, and Zenith uses 221-175 (their part number). These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second.
Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acarand nextto you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator's frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer. THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand, The flyback transformer receives current alternating at about 15,750 times per second from the herizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 24,000 VOLTS ON IT AND IT CAN KILL YOU!! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply. COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green on
Wells Gardner and Electrohome monitors. Zenith monitors have all three: red, blue and green. The Wells Gardner and Electrohome monitor have another variable resistor in their emitter part of their color output transistors. These “cutoff controls" vary the amount of A.C. signal that the transistor amplifies and sends to the cathodes of the picture tube. The Zenith monitor has its cutoff controls in the interface section to vary the amount of signal going to the output transistors. The more signal, the more color. if you think this is confusing, here is another little hitch. The Electrohome and Zenith monitors both have the actual A.C. picture information signal going through the emitters of the color output transistors. The Wells Gardner has the A.C. signal going to the base of the transistors. The blanking and beam limiting signals which come from the blanking and beam limiting transistors in the interface section go inio the color output transistor base in the Electrohome and Zenith monitors, but enters into the emitter of the Wells Gardner monitor's color output transistor. Should you fee! adventurous enough to look at this signal on an oscilloscope, it should look like a square. The beam limiter helps control the brightness tevel, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture. PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply ~voltage and turns off the horizontai oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don't be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's 'C501 and emitter of X04 for the Electrohome monitor. Check the 95 voit test point (located near the “flyback”) for the Zenith monitor. The Wells Gardner monitor doesn't use this circuit, but an open in the horizontal section could cause the monitor to appear off, yet still have power supply voltage flying around. Here are the voltages you should receive: Wells Gardner = 130VDC Electrohome = 120VDC
Zenith = 95VDC
The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The G07-FBO or G07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1. THE PICTURE TUBE (OR CRT) —
ATTENTION! For information on picture tube replacement types, go to the last section, “P!CTURE TUBE INTERCHANGEABILITY”. The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. A defective cathode may cause the particular color it handles to be missing. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to tne picture tube anode. After jetting from the cathode throught. all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with isto find the manufacturer's name or model number printed on the chassis or chassis base. But what if the monitor was in a Texas dust storm or buried in volcanic ash and this information is no fonger there? Fear not! Each monitor has its own peculiarities and the following should help to identify them: The ELECTROHOME G07-904 (19”) and G07-902 (13") have their horizontal and vertical processing IC hidden under a silver can. A shiny metal top behind the “VERTICAL HEIGHT” and “HORIZONTAL FRE- QUENCY” control prove this is an Electrohome monitor.
The WELLS GARDNER K4906 (19") and K4806 (13") have their horizontal and vertical! processing IC outin the open directly behind the “VERTICAL HOLD” control. The ZENITH CO19MXRFO6 (19) monitor has its horizontal and vertical processing IC way in back by the picture tube. The monitor also has large white cables going from the main board to the neck board. 4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the screen, Moving the Control may distort the top part of your picture (or the side, depending on thegameand how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size.
CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this controi. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Controt which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN" Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the Position with a black mark on the knob. If you moveit, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls. The Zenith monitor has a 95 voit adjustment control. It is green and located behind the jack labeled 3D3. To discourage you from moving it, Zenith has placed a little glue on top of this control.
Parts Interchangeability
Some parts can be interchanged on all of the monitors. Here are the rules:
- You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance.
- You CAN swap any capacitor between monitors that has the same capacitance and voltage rating.
- You CAN swap many of the parts between the 19” and the 13" versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.
- You MAY BE ABLE to swap picture tubes between monitors, In the past you could swap any picture tube, but due to rampant engineering changes and new monitor models being introduced, you would need a computer to keep track of what could be swapped. For more information on this subject, go to “PICTURE TUBE INTERCHANGEABILITY”.
- You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise !S DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback". NONE OF THESE ARE INTER- CHANGEABLE!!
- You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube.
If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
Picture Tube Interchangeability
13” MONITORS
There are currently two 13” monitors being used: the Wells Gardner K4806 and the Electrohome G07-902. The picture tubes used are NOT interchangeable. The pins on the neck of the CRT will not fit in the socket should you use the wrong CRT.
Here is a chart for all the 13” color monitors Bally Midway uses. ELECTROHOME = G07-902 — 370ESB22 WELLS GARDNER K4806 -- 370KSB22
19” MONITORS Here it gets a little tricky. All of the picture tubes will fit no matter which is used. But if you use the wrong one, you will have problems with purity and/or dynamic convergence. Purity trouble means that the color won't be true. If you turn up the color control for one color, instead of seeing that solid color it will show blotches or blobs of other colors on the screen. Trouble with dynamic convergence means that there will be color fringing around solid lines at the edges of the screen.
The only way to ensure that you avoid these problems is to get the right picture tube or the right substitute. Here is a list of the 19” monitors and the CORRECT CRT numbers. ALL ELECTROHOME G07-904 — 9VMNP22 RCA 19VMJP22 RAULAND 510UJB22 HITACHi WELLS GARDNER K4906 — JOVLTP22 RCA I9VMLP22 ZENITH J9VMKP22 PHILLIPS
ZENITH CD19MXAFO6 — JOVMLP22 ZENITH I9VLTP22 RCA A9VMKP22 PHILLIPS The factory recommended CRT type could change in the future for one reason or another, but the listed picture tubes will work. As a matier of fact, you can call another picture tube company to see if they have a replacement number to recommend... .but caveat emptor — let the buyer beware.
NOTES
Monitor Schematics
19” COLOR MONITOR SCHEMATIC DIAGRAM
MODELS 19K4901, 19K4906, 19K4951, 19K4956 Power Supply Voltage and Symbols ve Gymnot | Voltage’; __Qpersting Clean _ : OSCILLOSCOPE WAVEFORM PATTERN 15V_ | Vert. Osc. SERVICE TECHNICIAN WARNING UTION: TIN The waveforms shown are as observed on the wide band
| @ | Syne | X-RAY RADIATION PRECAUTION: | SOLACE ee ee, SAEED, | oscilloscope with the monitor turned to a reasonably | |||
| Blanking | PONENTS ONLY WITH | MANUFAC: | strong signal and a normal picture. The voltages shown | ||||
| CRT Cut-Off | THIS PRODUCT CONTAINS CRITICAL | | TURER'S RECOMMENDED PARTS. | ‘on each waveform are the approximate peak ampll- | ||||
| - | _ ELECTRICAL AND MECHANICAL PARTS | AVERTISSEMENT: | POUR MAINTENIR | tudes. | |||
| | | toe ee. | ESSENTIAL | FOR | X-RAY | RADIATION | UE DEGRE DE SECURITE DE APPAREIL | If the waveforms are observed on the oscilloscope with |
| Hor2, Output | | | PROTECTION | DONT LE | OHCTIONNENENT: Koy | a poor high frequency response, the corner of the | ||
| Vert. Output | | | FOR REPLACEMENT PURPOSES, USE | CRITIQUE POUR LA SECURITE QUE PAR | ae wit idea =_ ee than bata | |||
| 7 | : | DES PIECES RECOMMANDEES PAR LE | an | je am | y | high | frequency pulse wi |
| (0) | 175V_ | Video Output | ONLY TYPE PARTS SHOWN IN THE | FABRICANT. | tend to be less, |
351 COLLECTOR Reo arb Bur _ otbPSur 2ecz0seLe/L8eK 25020601 8/1 geK 26¢20681 81 88K| 2SCwWIaBVE/CVE 2SCISI4BVEKVC 2SCIBI4BVC/CVC
(weve) 2 Fatwa ea ‘0202 shea)
| 1V/DIV 200uSECIDIV | 20VIDIV 10uSECIDIV | O.SIDIV SMSECIDIV | 2sciersy/ GR |
TP.31 DC COUPLED. 402-3 Te x ys mor Fon F BOTTOM LINE=0 VOC wanes
| 2V/DIV 200MSECIDIV | SVIDIV 20uSECIDIV | Q5IDIV 20u SECIDIV |
LC. 301, PINS F LC. 301, PIN 15
AAA"
1VIDIV SMSECIDIV 1VIDIV 20u SECIDIV
TP82 TP-31, AC COUPLED mn Box were) yy e367 srr800y ale SYNC AMP VOSC H.0SC waia23 Gs
803, soicws! 2OV/DIV SMSECIDIV 1VIDIV 200uSEC/DIV ‘psdsmiour (HOR CENTERING) e801 mses HY. UNIT L382 98s) ial LC. 301, PIN 13 NEGATIVE SIDE OF C303
ac i2ov ‘conz
[Fre-070
| 1VDIV 200uSEC/OIV | 2VIDIV SMSECIDIV | 1VDIV 2MSECIDIV |
K4901D, K4906D, K4951D 5833 12 K4956B
REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A * on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.
MAIN BOARD
| Ret. No. | Part No. | Description | Ref. No. | Part No. | Description |
RESISTORS RESISTORS (CONT.)
| R201 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R369 | 203X5602-329 | 680K Ohm, 5%, 1/2W Comp. | ||
| R202 | 203X6500-523 | 30 Ohm, 5%, /4W Carbon | R370 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | ||
| R203 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R371 | 203X9014-584 | 1K Ohm, 5%, | 1W Metal Oxide | |
| R204 | 203X6700-327 | 100 Ohm, 5%, 1/2W Carbon | R372 | 203x9101-119 | 12K Ohm, 5%, 1W Metal Oxide | ||
| R205 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | R375 | 203X6700-763 | 6.8K Ohm, 5%, 1/2W Carbon | ||
| R206 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R376 | 203X9104-404 | 270 Ohm, 5%, 2W Metal Oxide | ||
| R207 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R377 | 203x6500-447 | 150 Ohm, 5%, 1/4W Carbon | ||
| R208 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R378 | 203X6500-886 | 410K Ohm, 5%, 1/4W Carbon | ||
| R209 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R379 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | ||
| R210 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R380 | 203X6500-865, | 8.2K Ohm, 5%, 1/4W Carbon | ||
| R211 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R381 | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide | ||
| R214 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R383 | 203X9014-387 | 150 Ohm, 5%, 1W Metal Oxide | ||
| R215 | 203X6501-126 | 400K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | ||
| R216 | 203X8500-645 | 4K Ohm, 5%, 1/4W Carbon | R503 | 204X1700-535 | 150 Ohm, 5%, 15W Metal Oxide | ||
| R217 | 203X6500-405, | 100 Ohm, 5%, 1/4W Carbon | R504 | 203x9014-267 | 47 Ohm, 5%, 1W Metal Oxide | ||
| R218 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, 1/4W Carbon | ||
| R219 | 203X6501-126 | 400K Ohm, ~%, 1/4W Carbon | R506 | 203X9104-105 | 15 Ohm, 5%, 2W Metal Oxide | ||
| R220 | 203X6500-645 | 1K Ohm, 5%, | i/4W Carbon | R507 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | |
| R221 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R601 | 204X 1625-058 | 3.3 Ohm, 5%, 10W WW | ||
| R222 | 203X6500-762 | 3.3 Ohm, 5%, 1/4W Carbon | R701 | 203X9105-141 | 2.2 Ohm, 5%, 2W Metal Oxide | ||
| R224 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2W Carbon | ||
| R225 | 203X6500-169, | 10 Ohm, 5%, 1/4W Carbon | R201 | 204x2070-072 | 2K Ohm-B Semi-Fixed | ||
| R226 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R301 | 204x2070-084 | 5K Ohm-B Semi-Fixed | ||
| R227 | 203X6501-044 | 47K Ohm, 5%, 1/4W Carbon | VR303 | 204x2070-055 | 500 Ohm-8 Semi-Fixed | ||
| R228 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | VR351 | 204X2070-072 | 2k Ohm-B Semi-Fixed | ||
| R229 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | VR352 | 204x2070-072 | 2k Ohm-B Semi-Fixed | ||
| R230 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | |||||
| R231 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | |||||
| R232 | 203X6500-869 | 8.2K Ohm, 5%, 1/2W Comp. | |||||
| R233, | 203X6500-468 | %, | 1/4W Carbon | ||||
| R234 | 340X2820-934 | AW Carbon | CAPACITORS | ||||
| R235 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | C201 | 203X0014-088 | 1000 uF, 16V, Electrolytic | ||
| R236 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | 202 | 202X7200-064 | 330 pF, 500V, Ceramic | ||
| R301 | 203X6500-508 | 270 Ohm,5%, 1/4W Carbon | 6203 | 202X7200.043 | 220 pF, 500V, Ceramic | ||
| R302 | 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | C204 | 202X7200-043 | 220 pF, 500V, Ceramic | ||
| R303 | 203X6500-863 | 8.2K Ohm, 5%, | 1/4W Carbon | C205 | 203X0014-076 | 470 uF, 16V, Electrolytic | |
| R304 | 203X6500-724 | 2.2K Ohm, 5%, 14W Carbon | 6208 | 203X 1810-149 | 0.1 uF, 125V Mylar | ||
| R305 | 203X6500-842 | 6.8K Ohm, 5%, 1/4W Carbon | C207 | 349X2232-109 | 022 uF, 100V Mylar | ||
| R306 | 203X6003-201 | 7.5K Ohm, 2%, 1/4W Carbon | 6301 | 203X0014-065 | 330 uF, 50V Electrolytic | ||
| R307 | 203X6500-825 | 5.6K Ohm, | 5%, 1/4W Carbon | 302 | 203X 1600-563 | 0.033 uF, 50V Mylar | |
| 309 | 203X6500-965 | 22K Ohm, 5%, 1/4W Carbon | 303 | 203X0629-037 | 3.3 uF, 50V Electrolytic | ||
| R310 | 203X6500-988 | 39K Ohm, 5%, 1/4W Carbon | C304 | 203X1600-366 | 0.068 pF, 50V Mylar | ||
| R311 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C306 | 203x0412.012 | 2.2 uF, 16V Tanta! | ||
| R312 | 203X9014-741 | 4.7K Ohm, 5%, 1/4W Carbon | 307 | 203x1600-634 | 0.033 UF, SOV Mylar | ||
| R313 | 204X1450-537 | 1K Ohm, 5%, 5W Carbon | €308 | 203X0025-174 | 3.3 uF, 50V Electrolytic | ||
| R314 | 203X6500-481 | 220 Ohm, 5%, 1/4W Carbon | 309 | 203x 1207-100 | 0.068 UF, 100V PP | ||
| R315 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | C310 | 203X0629-061 | 10 uF, 100V Electrolytic | ||
| R316 | 203X6500-762 | 3.3K Ohm, | 5%, | 1/4W Carbon | 311 | 203X0041-025 | 10 uF, 160V Electrolytic |
| R317 | 203X6700-107 | 12 Ohm, 5%, | 1/2W Carbon | 312 | 202X7050-248 | 1000 pF, 500V Ceramic | |
| R318 | 203X6500-540 | 390 Onm, 5%, 1/4W Carbon | C313 | 203x0040-052 | 47 uF, 160V Electrolytic | ||
| R319 | 203X6500-645 | 1K Ohm, 5%. 1/4W Carbon | 314 | 203x 1201-265 | 0.033 uF, 200V PP | ||
| R320 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | C315 | 203x0629-023, | 1 UF, 50V Electrolytic | ||
| R321 | 203X6501-224 | 270K Ohm, 5%, 1/2W Carbon | C351 | 203X0629-029 | 1 uF, 50V Electrolytic | ||
| Ra22 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | 0352 | 203X0619-045, | 47 uF, 25V Electrolytic | ||
| R351 | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon | C353 | 203X1190-015 | 0.0082 pF, 50V Mylar-PP | ||
| R352 | 203X6500-785 | 3.9K Ohm, 5%, 1/4W Carbon | C354 | 203X0619-045 | 47 uF, 25V Electrolytic | ||
| R353, | 203X6501-086 | 68K Ohm, 5%, 1/4W Carbon | C355 | 203X1600-366 | 0.0068 pF, 50V Mylar | ||
| R354 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C356 | 202X7050-483 | 0.01 uF, 500V Ceramic | ||
| R355, | 203X9205-143 | 6.8K Ohm, 5%, 3W Metal Oxide | 359 | 202X8065-608 | 100 pF, 500V Ceramic | ||
| R358 | 203X5601-878 | 56K Ohm, 5%, 1/2W Carbon | C360 | 202X7050-366 | 0:0033 pF, 500V Ceramic | ||
| R360 | 203X6500-561 | 470 Ohm, 5%, 1/4W Carbon | C361 | 202X7050-483 | 0.01 uF, 500V Ceramic | ||
| R361 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C362 | 202X7203-032 | 0.01 uF, 50V Ceramic | ||
| R362 | 203x9014-645 | 1.8K Ohm, 5%, 1W Metal Oxide | 50363 | 203X1270-911 | 8700 pF, 1.5 KV PP | ||
| R363 | 204X1527-751 | 3.9K Ohm, 5%, 7W Metal Oxide | #0365 | 203X1201-265 | 0.33 uF, 200V PP. | ||
| R364 | 203X6500-246 | 22 Ohm, 5%, 1/4W Carbon | C366 | 203X0019-026 | 22 uF, 25V Electrolytic | ||
| R365, | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | 6367 | 202X8065.162 | 6 pF, S00V Ceramic | ||
| R367 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C368 | 202X7203-032 | 0.01 uF, 50V Ceramic | ||
| R368 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | 372 | 203X1207-125 | 0.1 uF. 100V PP |
MAIN BOARD (CONT)
| Ret. No. | Part No. | Description | Ref. No. | Part No. | Description |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)
| C380 | 202X7200-087 | 470 uF, 500V Ceramic | Q206 | 200X3181-523. | Transistor (NPN) 2SC1815GR |
| A501 | 203X1810-149 | 0.1 uF, 125V Mylar | Q207 | 200X3181-523 | Transistor (NPN) 2SC1815GR |
| 40502 | 202X7050-282 | 1500 pF, 500V Cerantic | Q208 | 200X3181-523 | Transistor (NPN) 2SC1815GR |
| 4503 | 202X7810-214 | 2200 pF, 125V Ceramic | Q209 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| 0504 | 202X7810-214 | 2200 pF, 125V Ceramic | 210 | 200x3181-523 | Transistor (NPN) 2SC1851GR |
| C505 | 203X0220-075 | 560 uF, 200V Electrolytic | Q301 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| 506 | 203X0040-034 | 22 uF, 160V Electrolytic | 302 | 200x3207-306 | Transistor (NPN) 28C2073LBGL2 |
| 507 | 203X0041-057 | 47 uF, 160V Electrolytic | 2303 | 200x3207-306 | Transistor (NPN) 2SC2073LBGL2 |
| 701 | 203X0019-092 | 1000 uF, 25V Electrolytic | Q351 | 200X3248-217 | Transistor (NPN) 2SC2482BK |
| 702 | 203x0634-061 | 10 uF, 100V Electrolytic | 9352 | 200X4589-802 | Transistor (NPN) 2SD898B |
| 6703 | 202X7050-248 | 1000 pF, 500V Ceramic | ae! | o0x2900-099 | ie Hat 1429 |
1501 200x2600-18: SEMICONDUCTORS .
| 0203 | 201X2010-159 | Diode, 1S2076-27 | |||
| D204 | 201X2010-159 | Diode, 1S2076-27 | : | TRANSFORM ERS & Ahn | |
| 205 | 201X2010-159 | Diode, 1S2076-27 | 351 | 201KArio 38 | oe |
| 0206 | 201X2010-159 | Diode, 1$2076-27 | L352 | 201%5000-083 | Goll, Horta. Size |
| 207 | 201X2010-159 | Diode, 1S2076-27 | ‘701 | 811X0004-007 | Coil, Adg. |
| 7351 | 202X1300-080 | Transformer, Hor. Drive | |||
| Ooze | So aioeD | pena re | Aw 1352 | 200Xx8720-301 | HV-Unit M-11 |
| D209 | 201X2010-159 | Diode, 1S2076-27 | |||
| D301 | 201X2010-165 | Diode, ISS81 | |||
| 0302 | 201X2010-159 | Diode, 1S2076-27 | MISCELLAN EOUS | ||
| D303 | 201X2010-159 | Diode, '$2076-27 | F501 | 204X7120.073 | Fuse, 4 Amp. 125V |
| 0304 | 201X2120-009 | Diode, RH!V | 402 | 208X5008.632 | Recep W Wire 3P-M-BG |
| D305 | 201X2120-009 | Diode, RH-IV | P201 | 204X9600-466 | Plug, PWB 3P-J |
| D306 | 201X2010-159 | Diode, |S2076-27 | P202 | 204X9601-477 | Plug, PWB 6P-Q |
| D501 | 201X3120-216 | Diode, RM-1AV | P401 | 204X9600-298 | Plug, PWB 4P-B |
| A502 | 201X3120-216 | Diode, RM-1AV | P501 | 204x9600-249 | Plug, PWB 2P-B |
| 40503 | 201X3120-216 | Diode, RM-1AV. | Pot | 204X9600-304 | Plug, PWB 4P-C |
| 40504 | 201X3120-216 | Diode, RM-1AV | TH501 | 201X0100-112 | Thermistor |
| D505, | 201X3120-216 | Diode, RM-1AV | |||
| 0506 | 201X3120-216 | Diode, RM-1AV | |||
| D701 | 201X2130-234 | Diode, RU-2V | FINAL ASSEMBLY PARTS. | ||
| 0702 | 201X2120-009 | Diode, RH-1V | AX 88X0138-506 | AQ9VLTP22 Pix Tube | |
| 201 | 200X3181.523 | Transistor (NPN) 28C1815GR | 205X9800-158 | LateraiiPurity Assembly | |
| 202 | 200X3181-523 | Transistor (NPN) 28C1815GR | A | 202X1111-201 | Yoke Deflection |
| 203 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM | 204X9301-255 | CRT Socket | ; |
| Q204 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM | 291X5004-262 | Automatic Degaussing Coil Unit | |
| 0205 | 200x4086-260 | Transistor (PNP) 2SA562-Y-TM |
NECK BOARD RESISTORS CAPACITORS
| R401 | 203x6000-729 | 220 Ohm, 5% 1/4W Carbon | C401 | 202X7050-269 | 1200 pF, 500V Ceramic |
| R402 | 203x6500-540 | 390 Ohm, 5% 1/4W Carbon | 402 | 202X7050-248 | 1000 pF, 500V Ceramic |
| R403 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | C403 | 202X7050-248 | 1000 pF, 500V Ceramic |
| R404 | 203X6000-729 | 220 Ohm, 5% 1/4W Carbon | C404 | 202X7050-282 | 1500 pF, 1.5KV Ceramic |
| R405 | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | C405 | 202X7050-483 | 0.01 uF, 500V Ceramic |
| R406 | 203x6000-661 | 820 Ohm, 5% 14W Garbon | |||
| R407 | 203X6000-729 | 470 Ohm,.5% 1/4W Carbon | |||
| R408 | 203x6000-998 | 270 Ohm, 5% 1/4W Carbon | SEMICONDUCTORS | ||
| R409 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | 401 | 200X3206-800 | Transistor (NPN) 2SC2068LB |
| R410 | 203X9104-824 | 15K Ohm, 5% 2W M.O. Forming | 0402 | 200X3206-800 | Transistor (NPN) 2862068LB |
| Ratt | 203X9104-824 | 15K Ohm, 5% 2W M.O, Forming | 403 | 200%3206-800 | Transistor (NPN) 28C2068LB |
| R412 | 203X9104-824 | 15K Ohm, 5% 2W M.O. Forming | |||
| R413 | 203X6000.998 | 2.7K Ohm, 5% 1/2W Comp. | |||
| Rata | 203X6000-998 | 2.7K Ohm, 5% 1/2W Comp. | MISCELLANEOUS | ||
| R415, | 203X60C0-998 | 2.7K Ohm, 5% 1/2W Comp. | 7 | ||
| RaI6 | 203X9105-154 | 22 Ohm, 5% 2W Metal Oxide | Pty | Fisraseondeo | Gana |
| R419 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | P403 | 204X9600-981 | ein Pin 1P-D |
| R420 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | + | 10+ | |
| . | P701 | 204X9601-020 | Plug, PWB 4P-E | ||
| R421 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | |||
| VR401 | 204X2115-014 | 500 Ohm, -B Semi-Fixed | |||
| VR402, | 204X2115-014 | 500 Ohm, -B Semi-Fixed | |||
| VR403 | 204X2115-006 | 5K Ohm, -B Semi-Fixed | |||
| VR404 | 204X2115-006 | 5K Ohm. | -B Semi-Fixed | ||
| VR405 | 204X2115-006 | 5K Ohm, -B Semi-Fixed |
‘Blug onten RED X101.X103 and XI08 VIDEO AMP, 25C454C X102.xI04 and XI06 VIDEO_AMP. 250673
wean riven sre pf ee
aan art
X01 POWER DRIVE 25C2688 X 902 ERROR AMP 2SC1890
- —] X303 BEAM LIMITER 254673 304 BLANKING 25C4B4C or asclees 301x302 x800.x308 rig 2StSs4eeresciees
Fe] FP Xor=xi08 RGB VIDEO OUTPUT 28ca6il or Sscisiav
rom 90-1283) com)
SU -1133A MAIN PCB ASSY
X701_X-RAY PROTECTOR 28ca54c or 25c1685 28cisor
acizov 6o¥t/S0n2 ol 4 OUT PG, ascasriv 38098 or 28ca0i or 8e26 00K 280869 or 280820 a foc] Schematic Notes Unless otherwise specified Resistance: (Q) (K->KQ, M--MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1-> (yF) working voltage -> 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP -© non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. Q indicates test point connection ch indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety syrabol with identical type.
Parts identification on circuit boards: e.g. SU1126A (R107 = R107) SU3030A (R113 = R3113)
19" COLOR GAMEMONITOR SCHEMATIC DIAGRAM
reer onfet Gut 29C 2060. 8A.sx 29020681 81.50%
ok 19203, eecersr/o Stevo —T__ |ascses (280945 LORIVE; — [G.oRivE] (CUTOFF) [6 CUTOFF)
lL
wanags
| ear 101 | Sass Bear fuser)
nor may HWUNIT Been Ree] T352 10008 Shey a oo per
K4956RD- 5638 MO5 1-00C52-A019
V. PARTS
30-312000
23-308700
98-021500
98-010900
Figure 4. Coin Door, Over/Under With Cash Box (700-0164-01)
15-951200
31-610000
Figure 5. Coin Mechanism Assembly (700-0164-01)
812-1024-00-01 Nut, Hex, #10-24 Cad 822-0010-00-01 Washer, Split Lock, #10, Znc
006-8004-10-0A PK WT l. 700-0168-01 CB Assy, Trackball, Converter
Control Assy, Joystick, 8-Pos
700-0162-01 Contro! Assy, Trackbal, 2.25D, 5V
570-0035-01 Sw, PB, SPDT, 125V, 0.1A,
001-8041-01-0A Harness Control Chassis
NN 001-8034-01-0A 800-0227-01 Panel, Control, Snakepit Bezel, Black Anodized, Led Sw 807-1024-16-02 4 Carriage Bolt, 10-24 X 1, Black i 807-1024-40-02 Carriage Bolt, 10-24 X 2.5 Black
760-0009-01 Cable Tie Mount (Bulk)
570-0039-01 Switch, PB, SPST, Round, Red
Figure 6. Control Panei Assembly, Snakepit (000-8002-10-0A)
15-9468 Ball Handle
18-9471 2" Washer
30-0933 va" E Ring
15-9478 Switch Actuator (.500” Dia, for 4-Way Joystick)
15-9470 Switch Actuator (.600" Dia. for 2- & 8-Way Joystick)
Figure 9. Wico Joystick Assembly (700-0163-01)
905315-2 Legend Plate (Red)
905306-1 905310-2 a Lens Cap (Red) —)
905320 ——- Plunger
Return Spring aera
905303
Mounting Washer NS
905305-2 Wedgebase Lamp (12V.25A)
404868-1
(Terminals .250) Lamp and Switch Holder. mp (Te —— 905325-1 r—- (Black)
905304 Fixing Nut
905335-1 SP Switch
Figure 8. Coinco Switch Assembly (570-0039-01) Swe”,
(15A, 250VAC, Terminals .250 Silver Contact)
COINCO SWITCH ASSEMBLY (570-0039-01) PARTS LIST
PART NO. (COINCO) DESCRIPTION QUANTITY
| 905310-2 | LENS CAP (RED) | 1 |
| 905315-2 | LEGEND PLATE (RED) | 1 |
| 905320 | PLUNGER | 1 |
| 905306-1 | RETURN SPRING | 1 |
| 905325-1 | BODY/SEZEL (BLACK) | 1 |
905303 MOUNTING WASHER 1 404868-1 LAMP AND SWITCH HOLDER (TERMINALS .250) 1
| 905304 | FIXING NUT | 1 |
| 905305-2 | WEDGEBASE LAMP (12V.25A) | 1 |
| 905335-1 | SP SWITCH (154, 250VAC, TERMINALS .250:SILVER CONTACT) | 1 |
15-172601
15-174100
15-172800
#0020500 15-174400
23-199100
15-172900
15-172201 30-131800 _ |
Figure 7. Track Ball Assembly (700-0162-01)
NOTES
VI. SERVICE BULLETINS
April 29, 1985
SERVICE BULLETIN
GAME: SENTE 'TRIVIAL PURSUIT'
SUBJECT: PROGRAM CARTRIDGE INTERCHANGEABILITY BETWEEN UPRIGHT AND COCKTAIL GAMES
- Program cartridge E-PROM Date Code 12-84 can only be used in upright games only.
- Program cartridge E-PROM Date Code 2-12-85 can be used in upright and cocktail games.
- When picture fails to flip properly in cocktail games, check dip switch setting and program cartridge E-PROM Date Code.
Andy Ducay Technical Service Manager
AD/dd
December 19, 1984
SERVICE BULLETIN
GAME: BALLY SENTE SAC I (Serial Nos. 101 to 218)
CONDITION
A possible 117VAC short condition under Electronic Chassis Assembly (000-6011-10-0A) when panel is moved in and out.
MODIFICATION
When the 117VAC Safety Switch was eliminated, wire nuts were used to secure the wires. They can be pulled off, and to prevent a short condition, tape and dress these two wires.
Andy Ducay Technical Service Manager
AD/dd
SELF TEST
Enter the self test in game over by moving self test switch on electronic panel to the right.
TEST SEQUENCE
RAM ROM TEST
A. Only first error encountered is displayed B. Error address is displayed on screen
SOUND BOARD TEST
A. Sound board ok
B. Sound board error
SWITCH TEST
OPTION SWITCHES
A. Factory settings B. Option switch Hl & Gl
BOOKKEEPING
A. Reset bookkeeping during self test as per instruction on screen
RETURN TO PLAY MODE