Last Duel
Last Duel (US New Ver.) (Capcom, 1988) · Manual · 20 pages · 22 sections · original scan
< =)
< =
O U =) ~ WY) < E ~
CAPCOM, USA INC.
Invites You To Use
OUR TOLL FREE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER CAPCOM GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS.
Continental U.S. (800) 843-4632 California (408) 745-7081 FAX (408) 745-7920
B Wen
WARRANTY, REPAIR AND RETURN POLICY
. *90 DAY FULL PARTS WARRANTY.
. *90 DAY FULL ELECTRONICS WARRANTY (SEE RMA BELOW).
. MINIMUM $40.00 SERVICE CHARGE FOR ALL NON-WARRANTY REPAIRS OR RETURNS.
. ANY UNAUTHORIZED NON-FACTORY REPAIR OR ATTEMPTED REPAIR VOIDS WARRANTY.
(‘ALL WARRANTY PERIODS BEGIN ON THE DATE OF PURCHASE FROM CAPCOM)
RETURN MERCHANDISE AUTHORIZATION — (RMA)
. ALL RETURNED MERCHANDISE MUST HAVE AN RMA NUMBER CLEARLY VISIBLE ON THE OUTSIDE OF THE PACKAGE.
. ALL RMA NUMBERS MUST BE OBTAINED FROM CAPCOM BY AN AUTHORIZED CAPCOM DISTRIBUTOR. (PLEASE HAVE CAPCOM SERIAL NUMBER AVAILABLE VW/HEN CALLING FOR AN RMA #).
. ALL PC BOARDS RETURNED TO CAPCOM WITHOUT AN RMA NUMBER WILL NOT BE ACCEPTED.
. CAPCOM WILL SHIP ADVANCE REPLACEMENT BOARDS TO DISTRIBUTORS OR AT DISTRIBUTORS REQUEST, DROP-SHIP BOARDS DIRECT TO THE OPERATOR.
. ADVANCE REPLACEMENT BOARDS WILL BE BILLED TO THE DISTRIBUTOR UNTIL RECEIPT OF A RETURNED BOARD BY CAPCOM AT WHICH TIME A CREDIT WILL BE ISSUED.
. ALL REPAIRS AND/OR REPLACEMENTS WILL BE SHIPPED BY CAPCOM WITHIN 24 HOURS OF RECEIPT OR REQUEST. (SUBJECT TO AVAILABILITY OF BOARDS).
. FOR ANY CAPCOM PRODUCT PURCHASED AFTER 11/1/87, ACAPCOM WARRANTY CARD MUST BE ON FILE FOR EACH BOARD TO FACILITATE REPAIR & RETURN.
Before You Get Started . . . Stop!
- Does you new game package include all listed parts? (Is it complete?)
- Isthe game you have chosen to transform able to supply all the required voltages for the new game?
- Isthe monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
- Do you have the necessary tools? (See the recommended tool list)
Caution
F.C.C. Regulation Compliance
The PC. board cage supplied with this new game kit must be utilized and terminated to ground at the time of installation. This is to avoid radio frequency radiation and comply with the limits for a class ‘A’ computing device pursuant to sub-part ‘J’ of part 15 of FCC. rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference — in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference.
Installing and Servicing Your
©CAPCOM
New Game Package
Table of Contents
New Game Package Contents..............0 0.000. c eee eee ee bees 2
Power and Monitor Requirements . 2.0.0... eee 2
Recommended Tools and Supplies ..............0-0-0000- $a eee eet p resis? 3
Dip Switch Tables... 000 ee eee ... 34
Game Description... 0... ee Pe aeareiwew ewes : 5
Installation Procedures... 6. ee 6
Helpful Hints... 2... eee .... 12
Control Panel Positioning . 22 ee aay dees pasa, asp ae aes es ae yas yy oes 13
Main Harness Connections . 2... 2. eee 14
Warranty Registration Card ................ ee ee ee ee ee 15
©CAPCOM
NEW GAME PACKAGE CONTENTS
1 Main Printed Circuit Board (PCB) 1 Control Panel Overlay 1 Set Legs, Bolts, & Spacers 1 Plex Control Cover 2 Connecting Wire Harness 1 Set Side Graphics 2 Eight-Way Joystick 1 Set Play Instructions & Function Labels 6 Player Button Assemmblies 1 Service and Installation Manual 1 Marquee
POWER REQUIREMENTS MONITOR REQUIREMENTS
+5 VDC Vertical Mount Raster Scan +12 VDC Negative Composite Sync
Recommended Tools and Supplies
CAPCOM new game package. Phillips and Slot Screwdrivers Socket Set Wire Cutters and Strippers Pliers or Channel Locks Electric Drill 3/32" © 1/4” © 7/16" Drill Bits 1/4" Plex Bit 1-3/16" Chassis or Sheet Metal Punch 1-1/14" Plex Hole Saw Small File Razor Knife and Sharp Blades Straight Edge
Dip Switch Tables
Optimize Your Profits Painting Supplies Paint Brush and Paint (don’t forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” © 1/8” © 3/16" Masking Tape 3 1/2" OR 4” Wire Ties Spray Window Cleaner and Rags
Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing.
If games aren't running about two and a half minutes long, then collections probably aren’t at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!
DIP SW-A
DIP SW-B
DIFFICULTY DIP SWITCH SETTINGS — LAST DUEL
1 CREDIT
1 CREDIT
DESCRIPTION
NORMAL EASY DIFFICULT VERY DIFFICULT *7, BUNUSED
ON | OFF OFF | ON
DIP SW-C “3, 4,7, 8BUNUSED
NUMBER OF PLAYERS
SOUND DURING DEMONSTRATION
CONTINUE
SCREEN DESCRIPTION
YES NO
YES NO
NORMAL FRIP
STAGE START FROM AUTO STAGE SELECT START FROM AIRPLANE STAGE
"4, SUNUSED
Dupe, ©CAPCOM CONTROL THE PLAYER USING 8-DIRECTION JOYSTICK AND 2 BUTTONS.
BUTTON 1: ATTACK BUTTON.
BUTTON 2: ROLLING ATTACK BUTTON (AT STAGES 1, 3 AND 6 WHEN PLAYER OPERATES AN AIRPLANE].
JUMP BUTTON [at STAGES 2. 4 AND 5 WHEN PLAYER OPERATES A CAR).
SURFACE ATTACK BUTTON (AT STAGES 2, 4 AND 5 WHEN IN SIMULTANEOUS 2-PLAYER MODE, AND BOTH PLAYERS ARE OPERAING AIRPLANES). 2-PLAYER SIMULTANEOUS MODE. POSSIBLE TO JOIN DURING SINGLE-PLAYER GAME.
PLAYER OPERATES EITHER AN AIRPLANE OR A CAR, DEPENDING ON WHICH STAGE HE’S IN.
IF IN SIMULTANEOUS PLAY MODE, BOTH AN AIRPLANE AND A CAR MAY BE OPERATED IN SOME STAGES.
Installation Procedures
Something To Think About
Your final product will be anew game. You have made a wise decision to transform a game that has seen better days in the all important cash box into a new game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end result is... anew game at a very low cost. Fact: Spend a little time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics. With a little paint, some wood putty and new lights, you will raise the profits of any game especially with the introduction of a new game package. The new game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary glitches do not occur. Remember: You are creating a new game. If you have any questions or just need some advice on any of your new game transformations, don't hesitate in giving a member of our technical staff a call
Let’s Get Our Hands Dirty
Preparing the Original Game for the New Game
Remove the following:
- Main logic board(s) 4. Monitor Bezel
- Control panel 5. Marquee
- Monitor plexiglass 6. Graphics
| would recommend painting your cabinet to give it a fresh new look. (If it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced Thoroughly clean out your cabinet.
Time To Install Your New Goodies
Before You Start . . . Remember DO NOT Do This Work With The Power On!
Logic P.C.B. Cage
Mount the logic cage securely (away from power supply). A Mark and drill pilot holes (3/32”) B Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C Install the PC.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots in the cage bottom.
Wire Harness
Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.
Connecting the Wire Harness to the Existing Wires
When you hook up the contro! panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors
- Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
- Solder the new wire designated for that position to the original wire you just stripped.
- Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
- Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is anew game, not a sloppy conversion.
Power Wires
- Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
- You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don't overload the edge connector pins and cause them to “burn”.
Monitor Wires
You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.
Speaker Wires
Find the two wires that are designated for the speaker and hook ‘em on up.
Coin Door Wires
I. Connect the designated wires to the coin switches and meter.
- Youcan connect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
- Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in:
GUESS WHAT?
You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.
Smoke Test
What Test?
Don't worry. Alll this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.
- Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
- Make sure the logic board, board cage, monitor and power supply are securely fastened in place. Double check the connectors to be sure they are wired and connected properly.
- Set the dip switches on the logic board to the factory recommendations. w
Time to Apply Power
- Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED)
- Listen for game sounds. If after one minute you have not heard any sounds: A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board.
- Howis the monitor image? A) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative). If your monitor does not have dual polarity positions for sync, then you will need to reverse the sync yourself by installing a simple one IC. circuit between the logic board and the monitor. (The following illustration shows a hookup for both composite and separate syncs.
HORIZONTAL SYNC INPUT FROM PC.B. 5 vec [OR COMPOSITE SYNC INPUT} HORIZONTAL SYNC OUTPUT TO MONITOR {OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM PC.B,
VERTICAL SYNC OUTPUT TO MONITOR
NOT USED <=
GROUND NOT USED
B) Now how’s your picture? © Is it centered? @ Is it too bright or dim? © Is it in focus? Check your monitor manual for these adjustments. If your screen looks ‘‘off’, then your new game transformation may have been in vain. So let's take the time to make the monitor look great. C)Is the picture upside-down? Check dip switch settings for screen flip.
Control Panel Assembly
1 Remove the buttons, joysticks and wire harness and put them aside for now. Do not remove the original panel overlay until the new holes have been drilled.
- Mark positions on the panel for the new holes. CAPCOM supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that your mew game investment is well worth protecting . . . and the control panel is the first place to show wear and tear. © You will need to cut this piece to size. Use the control panel as a template ¢ Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass.
- Now drill the holes in your panel that you have marked off for the buttons, joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes.
- — Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter.
- The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file.
- Remove the orginal graphics overlay from the panel. Clean up the panel and install your CAPCOM graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. No bubbles please. Now peel off the bottom half and do the same as you did for the top.
- Adhere the instruction and function labels. 8 Install the Plex Control Cover over your completed new game panel.
- Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible).
Marquee Installation
Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on anew game. Take your time . . . Don’t forget this is going to be anew game.
Side Graphic Installation
Be sure sides of game are clean and free of old adhesive, dust, etc. Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet}. Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing. Remove any small bubbles with a pin or razor blade (pop them)!
Finishing Touches
Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can’t get a coin into it. Once again go over every step of this new game transformation in your mind. Be sure everything is correct and to your liking Power up the game . Check all the coin switches. (Does the coin meter work?} Play your new game. Are all the player controls working? Are the game sounds present? Is the volume level proper? ¢ Are the dip switches set properly? eceom>s
Well, that’s about it. Good Luck.
HELPFUL HINTS
Simple audio check for Board: TYPICAL AUDIO CIRCUIT FOR CAPCOM BOARD:
+12VDC volume control
CONNECT EARPHONE BETWEEN POINT "A" & GROUND. AUDIO R6P102 FROM CPU BOARD SHOULD BE HEARD.
NEXT CHECK POINT"B" AND GROUND. ADJUST POT FOR LOUDNESS IN EAR- PHONE.
CHECK POINT"C" & GROUND FOR IN- PUT AUDIO TO PIN 3 OF HAI3001 AUDIO CHIP. audio in HAIZOOL to0u/1 Oy Tes et
tooustov Edge connector te (see wiring list for correct pins)
speaker connections
Also make sure Ground from +5VDC and Ground from +12VDC ARE
TIED TOGETHER. IF GROUNDS ARE FLOATING, you could have audio prob-
lems.
-— O- 8-WAY JOYSTICK TS cn | BUTTON
POSSIBLE 1 & 2 PLAYER LOCATIONS
Control Panel Positions
VOLUME
PCB Layout
Wire Color Solder Side
Black Ground
+5VDC
+5VDC
White
+12VDC Yellow
Key De [cone | Bown Not Used Red
Speaker (+) White
Video Red Red
Video Blue Blue Counter 2
Not Used
Speaker (—)
Not Used
Video Green Brown
Red
Video Sync
| Brown | Not Used | 15 | Brown | |
| White | Coin 2 | 16 | Coin 1 | White |
| 2P Select | 17 | IP Select | Gray |
IP Down Blue
| 20 | IP Left | Green |
2P Left
| Yellow | 2P Right | 2i | IP Right | Yellow |
| Orange | 2P Button 1 | 22 | IP Button | | Orange |
| Red | 2P Button 2 | IP Button 2 | Red |
Not Used
Not Used
Not Used Black | Ground Black | Ground Not Used
Not Used
Not Used
Ground Brown
Blue
Blue
Black
Black
CAPCOM GAME OWNER:
Please fill out card and register for Free drawing at COIN-OP SHOWS. YOU NEED NOT BE PRESENT TO WIN.
Remember to fill in S/N of PCB (S/N IS REQUIRED FOR DRAWING).
LAST DUEL SCHEMATICS AVAILABLE FOR CHARGE OF $5.00 FROM CAPCOM USA.
REGISTER FOR FREE DRAWING
| | | | NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES
BUSINESS REPLY MAIL
bt FIRST CLASS PERMIT #1685 SUNNYVALE, CA a Postage will be paid by addressee: Le bn PC CAPCOM U.S.A., INC. —
COIN-OP DIVISION PC 1283-C Old Mountain View/Alviso Rd. Sunnyvale, CA 94089
CAPCOM
1283-C Mountain View/Alviso Rd.
Sunnyvale, CA 94089 (408) 745-7081
COMPANY NAME
LAST NAME FIRST NAME
ADDRESS:
CITY STATE. ZIP CODE AREA CODE PHONE NO.
PRODUCT PURCHASED: DATE OF PURCHASE PURCHASED FROM: MONTH DAY YEAR COCO HOW WOULD YOU RATE THIS GAME. EXCELLENT VERYGOODT FAIRO POOR
HOW DID YOU HEAR ABOUT THIS GAME: MAGAZINE (FRIEND) OTHER
DO YOU OWN ANY OTHER CAPCOM ARCADE GAMES? YES NOD) PLAN TOBUY IN NEAR FUTURE Cl]
WHAT TYPE OF ROUTE DO YOU OWN: ARCADE [] SMALLROUTE [1 LARGE ROUTE 1] HOW MANY GAMESDO YOU OWN
WHAT CAPCOM ARCADE GAMES ARE YOU FAMILIAR WITH SPEED RUMBLER () SECTIONZC) LEGENDARY WINGS AVENGERS) 19431) STREET FIGHTER) OTHER OO
COMMENTS: