CATHODE RAY TOMES

Centipede TM-182 6th Printing

Centipede (revision 4) (Atari, 1980) · Technical Manual · 59 pages · 39 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

GAME SERIAL NUMBER LOCATION

Your game's serial number is stamped on a silver identification label located on the front of the game, under the control panel. The same serial number is also placed on the chassis of the monitor, power supply, Regulator/Audio Mt PCB, and the Centipede™ Game PCB. Please mention this number whenever calling your distributor for service.

MONITOR

GAME SERIAL NUMBER IDENTIFICATION TAG CENTIPEDE GAME PCB

REGULATOR/AUDIO I! PCB

Page 3

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 4

Copyright © 1981 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

The Centipede™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the signature analysis guide are protected by the new Copyright Act of 1976.

This Act provides for-increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.

In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year.

Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 1265 Borregas Avenue PO. Box 427 Sunnyvale, California 94086

Lithographed in the U.S.A. 3L

Page 5

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari parts in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 6

Table of Contents

1 Set-Up Procedures A. New Features... 0.0.00. e eect n ee neeeeen eee eee 1 B. Game Inspection 3 C. Game Installation. . . 3

  • Voltage Plug Selection . wees 4
  • Interlock and Power On/Off Switches 4 D. Self-Test Procedure .........-..-.- vee 6 E. Option Switch Settings
  • Bonus Play Feature...
  • Coin Mechanism Multipliers ..........-. 60 eee rere eee eee eee
  • Examples of Game Price Settings . F. GamePlay ........-..-+-++--)
  • Attract Mode .
  • Ready-to-Play Mode ewe nha bina heer ee
  • PlayMode ........-- .
  • High Score Initial Mode ...... 0... e cece cece eee eens 16

2 Maintenance and Repair A. Cleaning... 2.0... eect e ene et nent eee e enna B. Fuse Replacement C. TheControl Panel ..........-

  • LED Start-Switch Replacement .
  • Leaf-Switch Replacement. ...
  • Mini-Trak Ball™ Maintenance and Repair . D. Monitor Removal ........6...eee sees E. Printed-Circuit Board Removal .
  • Game PCB Removal ...
  • Regulator/Audio Il PCB Removal F. Fluorescent Tube and Speaker Replacement x G. Game Operation. ..... 60... cece eee eee ence eee eens

3 Illustrated Parts Lists Illustrations and parts lists begin on page .... 6... ss eee e eee eens 27

Page 7

List of Illustrations

Figure 1 Overview Of Game ... 0... ccc n eens 2 Figure 2 Installation Requirements . . 3 Figure 3 International Voltage Plug Selection . . 4 Figure 4 Interlock and Power On/Off Switches ............ 0.00 e cece ee eee 5

Figure 5 Location of Self-Test Switch, Volume Control and Option Switches ... 6 Figure 6 Self-Test Procedure. ... 7 Figure 7 Game Option Settings - 10 Figure 8 Game Price Settings ....... 2.0... cece cece cece ene tenes 11

Figure 9 Coin Counter Option Settings ......... 0... eee cece eee ee eee 13 Figure 10 Opening the Control Panel and Replacing Switches . 18 Figure 11 Mini-Trak Ball™ Maintenance and Repair........ . 20 Figure 12 Monitor Removal ..........0 0. eee cece eee een tenes 21

Figure 13. Printed-Circuit Board Removal Figure 14 Fluorescent Tube Replacement Figure 15 Power Distribution ........ : . Figure 16 Signal Distribution ..... 2.0.0.6. ccc ccc cece eee e eens

IHlustrated Parts Lists: Figure 17 Cabinet-Mounted Assemblies Figure 18 Control Panel Assembly... . Figure 19 = Mini-Trak Ball™ Assembly Figure 20 Regulator/Audio ll PCB Assembly .............. 00: e cece eee 34

Figure 21 Centipede™ Game PCB Assembly .................0 00sec eee eee 36 Figure 22 PowerSupply Assembly. ..........0 0.00. e cece eee eee 40 Figure 23 Fluorescent Light and Speaker Assembly. ..............--.00-005 42 Figure 24 American-Made Coin Door Figure 25 British-Made Coin Door ............s.scssssssseseeeeveeeee,

Page 8

vi

NOTE If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A.

Service only

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) s From California, Alaska, or Hawaii (408) 745-2900 ee Service from anywhere in the area shown in white & toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 124 World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey Zs (201) 469-5993 From anywhere else in this area & joll-ree (800) 526-3849

EUROPE Service only

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

BS 06252155

Page 9

Set-Up Procedures

this assembly are Underwriters Laboratories Listed and Canadian Standards Association Certified. The addition of a foam pad on the rear access panel insures that the safety interlock switch will be completely closed when you lock this panel. Due to environmental factors, these panels can warp slightly, which could cause a switch to remain open. Additional Improvements: The wiring harness has been redesigned so that signal and power wiring are now separated to provide ease of maintenance and troubleshooting. Second, all monitors used are UL-Recognized and CSA-Certified, thus providing the most reliable and highest quality monitors available in the marketplace today.

In addition, the power supply chassis has been A. New Features fitted with a metal bottom plate, making it a totally self-contained unit. The Centipede™ game has several new parts. Even if you are familiar with Atari games, you should

note these important differences. The new parts are: @ Mini-Trak Ball™ Assembly. The widely used Trak Ball assembly has been redesigned. The basis for this compact, simplified design is a two-part molded plastic frame. Fewer parts in this control make servicing easier, and its very smooth action is designed for greater player accuracy. @ The circuitry has non-volatile memory for part of the high score table. This means that even if power is removed from the game, the three highest scores will permanently stay in memory. To erase these scores follow the instructions in Figure 6, Self-Test Procedure. Fourth, the attraction panel and monitor shield are now made of tempered glass to facilitate cleaning and improve visibility.

@ To insure starting, the fluorescent light now includes a large grounded metal plate. In addition, the lamphoider and ballast transformer used in

Page 10

MONITOR FLUORESCENT LIGHT SHIELD

ATTRACTION PANEL

COLOR MONITOR

a)y x

MINI-TRAK BALL™ A

CONTROL

‘START: SWITCHES

CONTROL PANEL *, (ae

Le

COIN DOOR

cN

Figure 1 Overview of Game INTERLOCK SWITCH POWER ON/OFF SWITCH GAME PCB

REGULATOR! AUDIO Il PCB “> POWER SUPPLY

Page 11
WARNING: SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is mentioned, you will see this symbol:

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE | Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel, as well as the coin door; inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the square black plastic strainrelief plate in the wood slot at the bottom of the rear panel opening.
WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the monitor with your hands or metal objects held in your hands!

@ Note the location of the game's serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Centipede™ Game PCB, Regulator/Audio || PCB and monitor are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and monitor for secure mounting.

Cc. Game Installation

Figure 2 Installation Requirements Power 130 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 64x82 cm (25% x 32% in.) Game Height 181 cm (71% in.)

Page 12
  • Voltage Selection The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two or three colored voltage selection plugs.

Before plugging in your game, check your power supply. If the supply doesn’t have voltage selection plugs and a connector at J3 (see Figure 3), then the game operates on any voltage from 105 to 135 VAC. If the supply has the colored voltage selection plugs, make sure that the voltage selection plug on the power supply is correct for your location's line voltage. Check the wire color on the plug and see if it is correct per Figure 3.

  • Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the rear access panel and one

Line Voltage Range Voltage Selection Plug Color 90-110 VAC (100) Violet 105-135 VAC (120)* Yellow* 200-240 VAC (225) Blue 220-260 VAC (240) Brown *This is the only plug provided on the U.S. power supply. The international power supply includes the other three plugs.

VOLTAGE SELECTION PLUGS:

Figure 3 is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened. Check for proper operation of the interlock switches by performing the following steps: @ Be sure the access panel and the coin door are closed. @ Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the on position. Within approximately 30 seconds the monitor should display a picture. @ Slowly open the rear access panel. The monitor picture should disappear when the panel is Opened approximately 2¥2 cm (1 inch). Close and lock the access panel and repeat this step with the coin door. @ If the results of the preceding step are satisfactory, the interlock switches are operating properly. If the monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the on position.

WARNING

Fuse cover must be in place during game operation.

International Voltage Plug Selection

Page 13

SAFETY INTERLOCK SWITCH

POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 14

D. Self-Test Procedure

Part of the self-test procedure includes a display This game will test itself and provide data to dem- of the operator-selectable game options. Therefore, onstrate that the game’s circuitry and controls are we suggest you run the self-test procedure anytime operating properly. The data is provided on the mon- you need to change the game’s options. itor, the light-emitting diodes in the start switches, and the game speaker; no additional equipment is To run the self-test, follow the instructions outnecessary. lined in Figure 6.

GAME PCB

VOLUME INCREASE: TURN CLOCKWISE SELF-TEST SWITCH (US) SELF-TEST SWITCH (EURO- PEAN GAMES) VOLUME CONTROL Figure 5 Location of Self-Test Switch,

Volume Control and Option Switches

Page 15

Figure 6 Self-Test Procedure

Instruction Results if Test Passes (if results are not as indicated, see list of failures that follows)

  • Begi Set self-test switch to on position (see Figure 6).
  • Switch Test: One after another, activate and release all control-panel switches, the slam switch, and coin switches. *
  • Audio 1/0 Chip Test: One after another, press and hold 2 of the control-panel switches and at least one of the coin switches.
  • Audio /0 Channel Test: Press 1-player start button four times.
  • Background Color Test: Press 1-player start button at least 16 times.
  • Object Color Test: Press 2-player start button at least 16 times.
  • Moving Object Test: Watch the screen, and move the Mini‘Trak Ball around. Place the moving object in an open area of the screen. Press fire button several times.
  • Erasing the High Score Table (optional) The monitor displays the picture below. The game produces no sound at all. The two start-switch LEDs will stay on throughout self-test.

The centipede head moves around on the screen in directions corresponding to Mini-Trak Ball™ control.

As long as you activate (close) each switch, you'll hear a high beep.

Volume increases and pitch decreases with each additional switch that is activated.

You'll hear a high beep for each press of the button.

Background color changes with each press of the 1-player start button.

Objects on playfield change color.

Each press of the fire button changes the moving object to another moving object. At certain points in the series, the object will disappear. This is not a failure indication.

The current three highest scores are held in permanent memory, even if the game is unplugged. If you want to erase these scores, simultaneously press the fire and both start buttons. The 4 FF message in the upper left corner of the screen will then be displayed. The average game time data will also be erased, but still displayed on the screen.

  • End: When satisfied with test, set self-test switch to off position.
  • Activate coin switches by inserting at least one coin in each coin slot. You will not trip the coin counters as long as you stay in self-test.

NO. OF LIVES AT START OF GAME

ALL SWITCHES & TRAK-BALL INPUTS

BONUS COIN SETTING (means “for every 3 coins inserted, logic adds 1 more coin”). Blank it no bonus coins(s) given. See Fig. 8 tor switch settings.

GAME DIFFICULTY SETTING 9d PLAYS: 1:59 GAME TIME ENTIRE CHARACTER SET

Cc, R COIN MECH MULTIPLIERS (L, R if you have a 2-mech coin door)

TOTAL NO. OF CREDITS PLAYED

AVG. GAME TIME {accurate to + 4 secs.)

Page 16

Figure 6 Self-Test Procedure, continued

Results if Test Fails

  • Begin: RAM FAILURE is indicated by one to 10 beeps. Note the number of beeps and determine which RAM may be bad. To restart the test, press the reset pushbutton on the game PCB, or set the selftest switch to off, then again to the on position. Possible Bad Number of Beeps Given RAM Chip Location OOND TRONS i a

10 NS Any bad RAM must be replaced before the computer can check the other RAMs, as well as continue with the self-test.

ROMI/PROM FAILURE is indicated by two groups of numbers in the upper left corner of the screen. The number at the far left indicates the location of the failing PROM/ROM(s). Identify the bad ROMI/PROM with the table below. If the screen displays “garbage,” or the logic produces strange audio or randomly activates the coin counters, the chip at location J1 is probably bad. Ignore the hexadecimal numbers just to the right of the chiplocation number. Failing ROM/PROM Displayed Number Chip Location 0 DI 1 Et 2 FIH1

3 or “garbage” Jt AS

4* E5* 5 BICID3

“If you replace or erase this ROM, the number 4 FF will be displayed throughout the self-test. The next time you enter self-test, the 4 disappears after a game is played. Otherwise the self-test will continue to display the numbers 4 FF.

  • Mini-Trak Ball Test: The character doesn’t move in same direction as ball, jumps rather than moves smoothly, or doesn’t move at all. One of the Coupler PCBs in either Mini-Trak Ball contro! may be bad, harness wires or connector may be loose, Mini-Trak Ball reading circuitry on Game PCB may be bad, or Mini-Trak Ball bearings may need oiling.
  • Switch Test: Sound is constantly on, even though you are not activating any switch. Or, no beep is given for any switch, or LED is dark. indicates a bad switch, loose harness wires, bad LED-driving circuitry, volume turned all the way down, or loose connector.
  • Audio VO Chip Test: No increase in volume or decrease in pitch indicates bad custom audio I/O chip at location B/C/D3.
  • Audio /0 Channel Test: On one out of the four activations, no audio is produced. Indicates ‘one channel is bad in the custom /O audio chip at location B/C/D3 (replace entire chip).
  • Background Color Test: Background doesn’t change color, or doesn't display all 16 colors. Indicates bad color RAM chip. (RAM failure would have been indicated earlier with from 3 through 10 beeps.)
  • Object Color Test: Objects don't change color, or don’t display all 16 colors. RAM failure.
  • Moving Object Test: Object doesn’t change to another object. ROM/RAM failure.
Page 17

E. Option Switch Settings

  • Bonus Play Feature Centipede™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, will receive a bonus coin. Therefore, players receive 3 plays for $1.00.

This bonus feature encourages players to insert more money than just the minimum 50¢ you could require for one game. Various other bonuses are available (see Figure 8).

  • Coin Mechanism Multipliers Available since early in 1980, Atari games have a new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattern.

The right coin mechs are all the same to the game's logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a 3-mech door as the same. Refer to the diagram below.

ese] [fst

This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game’s logic. The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 1/x 4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.)

You can set these multipliers with toggles 3 thru 5 on the Centipede Game PCB switch assembly at location N8. For exact settings of these toggles, refer to Figure 8.

  • Examples of Game

Price Settings

Figure 8 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are all in the switch at location N8; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7, 8, and 9 provide “$” signs indicating Atari's recommendations.

Page 18

Figure 7 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Centipede Game PCB is mounted in place. When changing the options, verify proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will not cause an immediate change on the monitor screen during the attract mode.

Toggle Settings of 8-Toggle Switch on Centipede Game PCB (CENTER switch assembly when PCB is in game) 8 7 6 5 4 3 2 (at N9)

1 Option

On On Off Off

On On On Off

Off On

Off Off

On On On Off

Off Off On Off

On Off On English $

Off German

On French

Off Spanish 2 lives per game 3 lives pergame $ 4 lives per game 5 lives per game

Bonus life granted at every: 10,000 points 12,000 points $ 15,000 points 20,000 points § Hard game difficulty* Easy game difficulty* $ ‘credit minimum $ 2-credit minimum

$ Manufacturer's suggested settings

  • Refer to F. Game Play, for information on game difficulty. For pricing for “credits,” see Figure 8. Changing toggles 3-7 erases the high score table.
Page 19

Figure 8 Game Price Settings

The white block below contains Atari's suggested settings. All Circled numbers refer to game pricing labels you should use numbers 1 thru 8 are toggle settings on the 8-toggle switch at lo- with each situation (labels are on the following page). Use the cation N8, on the Centipede™ game PCB (the LEFT switch label no. 6 (indicated with®) only if you set toggle 8 at PCB switch assembly). assembly NQ of off.

50¢ PER CREDIT:

Bonus Bonus $.75 = 2 plays No bonus $1.00 = 3 plays 3 plays

25¢/25¢ Mechanisms

25¢ PER CREDIT:

Bonus No bonus $.50 = 3 plays

8765
25¢/25¢OnOnOnOn

Mechanisms ORC)

OnOnOffOn

an

Page 20

Figure 8 Game Price Settings, continued The switch settings below relate to options for game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Centipede™ game on free play, or if you have German coin mechanisms in your door. To achieve bonus plays, all coins must be inserted before pressing the start button. The label no. 6 shown below should be used only if you set toggle 8 at PCB switch assembly N9 to off.

Toggle Settings of 8-Toggle Switch on Centipede PCB (at N8). LEFT switch when PCB is in game

87654321Option
OnOnFree play
OnOff1 coin" for 2 credits
OffOn1 coin* for 1 credit$
OffOff2 coins* for 1 credit
OnOnRight coinmech x 1$
OnOffRight coin mech x 4
OffOnRight coin mech x 5
OffOffRight coin mech x 6
OnLeft coinmech x 1$

Off Left coin mech x 2

OnOnOnNo bonus coins$

On On Off On Off On On Off Off Off On On Off On Off

For every 2 coins* inserted, game logic adds 1 more coin*

For every 4 coins* inserted, game logic adds 1 more coin*

For every 4 coins" inserted, game logic adds 2 more coins*

For every 5 coins* inserted, game logic adds 1 more coin*

For every 3 coins* inserted, game logic adds 1 more coin*

*in the U.S. a “coin” is defined as 25¢ in Germany a “coin” is 1DM.

$ Manufacturer's suggested settings

Game Pricing Labels

oe Js @@ 2 coins =1 play ATARI

°e

JX”@1 coin= 1play

ATARI

KO@ @2 coins = 1 play

ATAR

& 0e@ r: 4 coins = 3 plays Ke @@ 2coins = 1 play “8 @@@ 3coins = 2 plays @@@@ 4 coins = 3 plays

© @@ 2 coins =1 play

A $1 coin =3 plays

(Susan B. Anthony coin)

eo. @ 1 coin = 1 play amar’ 2 play minimum (2 coins = 2 plays)

(For operator use—write in the appropriate phrase. Use @ permanent-ink water-resistant marker.)

Page 21

Figure 9 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4-Toggle Switch on Game PCB (N11)

4321

‘Two coin acceptors in the coin door: Two coin acceptors and a pushbutton utility coin switch in the game (cocktail-table cabinet): Three coin acceptors in the coin door:

OnOnBoth acceptors activate all coin

counters simultaneously.

OnOffBoth acceptors activate 2 count-

ers separately. 3 8B 3 3

33SOffOnBoth acceptors activate all coin
==counters simultaneously.
OffOffBoth acceptors activate 2 count-

ers separately. $ Do not use this setting.

Do not use this setting.

Utility coin switch will not activate a coin counter, if you do not hook it up. Both acceptors activate all coin counters simultaneously.

Utility coin switch will not activate a coin counter, if you do not hook it up. Left and right acceptors activate 2 coin counters se- Parately. All 3 are same denomination and they activate all coin counters simultaneously.

Left and center acceptor activate one coin counter; right acceptor activates another coin counter.

Left acceptor activates one coin counter; center and right acceptor activate another coin counter. Not for any currently designed 3-mech coin door.

Left, center and right acceptors activate 3 coin counters separately. $s

$ Manufacturer's suggested settings

F. Game Play

Atari’s Centipede™ game is a one- or two-player game with a color raster-scan monitor. The fast-moving action includes a variety of creatures dropping down from the top of the screen or flying in from its sides, most of them to attack the player. The player’s shooter is represented on the screen by a somewhat humanoid head. The player’s goal is to shoot at and destroy as many of these creatures and mushrooms as possible for a high point score, before the player's lives are used up. Players can maneuver their Mini-Trak Ball™ control anywhere within approximately the bottom fifth of the screen. However, they must move around mushrooms, since these are fixed, not “transparent”, objects. A fire button shoots individual shots upwards, or fires a hail of shots if pressed constantly. (Only one shot appears on the screen at atime.)

The game has five possible modes of operation: attract, ready-to-play, play, high score initial, and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled. Wait at least eight seconds after a game has been played before entering selftest or turning off the power. Otherwise, you may erase the high score table.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test. In this mode, the monitor displays two pictures simultaneously.

One of the pictures is operator-selectable for one of four languages. Placed in the center of the screen, the picture shows the high score table, game price, and the bonus-life achievement level. If the operator sets the Centipede game for free play, the game will not display a game price message.

The high score table shows the eight highest scores and their matching initials. If you erase the special “permanent” memory (see Figure 6, Self- Test Procedure), then this table will contain fictitious scores and initials. The table is redeveloped from subsequent games with scores of more than 12,102 points. Subsection 4, High Score Initial Mode, explains this table in more detail.

Page 22

Operators may choose one- or two-credit minimums by selecting one of the option switch settings on the game PCB (see Figure 7, Game Option Settings).

If the game is set for a 2-credit minimum, that message will be displayed on the screen. (No special message appears if Centipede is set to the opposite setting, namely 1-credit minimum.)

The other picture surrounds the high score table, game price and bonus-life achievement level messages. That picture displays a typical game-play sequence, with a field of colorful mushrooms through which a centipede crawls. The spiders bounce in from the sides of the screen, and fleas occasionally drop down from the top. In addition, scorpions will cross the screen at almost any point.

In this mode, the action exactly duplicates a typical game played by a moderately skilled player: the player's shooter moves freely within the limits of motion, shooting at spiders, centipedes, fleas and scorpions. Periodically the player is “destroyed” when a flea, spider or centipede head or body collides with the player’s shooter.

All the colors on the screen change with each wave. A new wave occurs when the player shoots all centipede parts remaining on the screen. At this point, a new centipede starts snaking its way down from the top of the screen.

The attract mode differs from real game play in that no head figures are shown at the top of the screen to represent the number of lives remaining, no sounds are produced, no scores are incremented, and none of the four player controls work.

At any time when the game is powered up, if the coin-door slam switch is closed, you will hear a special alarm sound. This sound alerts location personnel that the game has been abused.

  • Ready-to-Play Mode This mode begins when sufficient coins are accepted for a one- or two-player game. It ends when the 1-player start or 2-player start pushbutton is pressed. When this mode begins, the message CRE- DITS __ is displayed in the middle of the screen. The pictures are otherwise the same as those shown in the attract mode.

If you select the two-credit minimum and a player inserts enough money for only one credit, the message 2 CREDIT MINIMUM flashes on the screen until enough coins for the second credit are inserted.

In addition, CREDITS 0% is displayed if you have selected the option of two coins per credit, and the player has inserted only one coin. A “credit” is defined as the cost for each player to play one game. In other words, two credits will pay for: @ one player playing two games, or @ two players playing one game.

  • Play Mode The play mode begins when any flashing start pushbutton is pressed. The mode ends when the player’s last life is lost.

A player's shooter is enabled at the beginning of the play mode, and the audio starts. The appropriate LED start switch will then stay lighted until the end of the game. At this point it will flash if any credit remains.

The game begins with a playfield of randomly placed mushrooms. A centipede starts snaking its way across from the center top of the screen. The centipede changes direction when it runs into a mushroom or either the left or right boundaries of the playfield.

Page 23

When acentipede is shot, it breaks into two smailer ones, each with a head. Also, the part of the centipede that was shot leaves a mushroom in its place on the screen. When any centipedes reach the bottom of the screen, they start back up, but remain within the area of the player's shooter (the bottom fifth of the screen).

When a large centipede (that hasn’t been shot yet) reaches the bottom, it releases its tail, and this part changes into a new head. Also to provide player challenge, if a centipede is still alive when it reaches the bottom, new heads will enter the screen almost at the bottom of the sides. More of these heads will appear as time progresses.

The randomly moving spiders also appear in the first wave. The spiders can destroy a player, as well as any mushrooms they move over. This eliminates many mushroom targets for a player.

The player's shooter is moved by rotating the Mini-Trak Ball™ control. The shooter can be moved in all directions, but only within the bottom fifth of the screen. Pressing the fire button causes the shooter to fire shots upwards, either singly or in rapid-fire mode, if held down constantly. Mushrooms count 1 point when shot, and a player must fire four shots into a mushroom before it is destroyed and disappears. Centipede body parts count 10 points each, and the elusive heads (represented with small eyes on them) are worth 100 points each. Spiders are worth 300, 600 or 900 points, depending on how close they are to the player when shot.

A bombardment of fleas starts in the second wave; as the fleas descend, they leave a trail of new mushrooms behind them.

In the second wave, the fleas appear when a certain number of mushrooms remains at the bottom of the screen. This number increases as the game progresses, meaning fleas appear more often later on in the game.

Fleas have a value of 200 points when shot, and players must hit them twice to destroy them (the first shot just speeds them up).

The scorpion enters from either side starting in the fourth wave; it moves at a relatively slow speed. Later it increases its speed. When shot, a scorpion counts 1000 points—the highest-value target of all.

Page 24

As it travels across the screen, it “poisons” the mushrooms that it moves over and changes their colors. These mushrooms cause any centipedes that would collide with them to head straight towards the bottom of the screen, rather than continue snaking around. Players can stop a poisoned centipede by shooting its head.

In addition, these poisoned mushrooms as well as any partially shot mushrooms add 5 points to the player's score at the end of each life when the screen is resetting.

If the players are very skilled and earn at least 60,000 points, two things happen to increase player challenge: the fleas descend at a faster speed and the spiders restrict their movement to a smaller area at the bottom of the screen. (oa An important new feature of this game is the operator option for easy/hard game difficulty. In the easy game, the spider moves slowly up to a 5,000-point score, and then bounces at a higher speed. It also changes direction less often throughout the game than at the hard setting.

In the hard setting, the spider moves slowly only for the first 1,000 points, and then speeds up. It also changes direction more often throughout the game. In either setting, the spider always moves at a 45-degree angle or straight up and down.

Another operator option is the number of lives per game, ranging from 2 to 5 (see Figure 7 for switch settings). This number is displayed as small shooters at the top of the screen. The number is decreased by one each time a player is destroyed. The number is increased by one each time the player scores multiples of 10, 12, 15 or 20 thousand points, depending on the operator selection.

  • High Score Initial Mode If a player's score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. At the beginning of this mode, the characters A _____ appear on the screen. The logic will also display the messages GREAT SCORE and ENTER YOUR INITIALS.

Players enter initials one character at a time, choosing from the characters A thru Z and a blank space. Pressing the fire button selects the letter, and rolling the Trak Ball control changes the letters on the screen.

After the fire button is pressed the third time, the initials and score are transferred to the table. This table contains eight scores and appears during the attract and ready-to-play mode.

All but the highest three scores are erased whenever you enter the self-test, or press the RESET button on the game PCB, or turn off the power. This resetting replaces the lowest five scores with fi tious scores and initials.

If you erase the special “permanent” memory, the high score table is replaced with eight fictitious scores and initials. In other words, the table will always be displayed on the screen, possibly consisting of one or more realistic scores and players’ initials.

Page 25

Maintenance and Kepair

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if Mini-Trak Ball™ control, leaf switch or light-emitting-diode (LED) switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside ot the game and the coin mechanisms. In addition, you will need to regularly lubricate the Mini-Trak Ball control: for details see this chapter.

Page 26

NORMALLY CLOSED --~. (N.C.) CONTACT

NORMALLY OPEN-—_ > (N.0,) CONTACT — CAUTION Players may receive an electric shock if this control panel is not properly \ grounded! After servicing any parts on iy \ the panel, check that the ground wire is LIGHT-EMITTING-DIODE —/ \ COMMON firmly attached to the metal tab on the (LE.D.) CONTACTS ‘ inside of the control panel. Only then To remove LED switch: CONTACT should you lock up the game.

@ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires.

WHITE

VERT.MOTION PCB: GREEN, RED, BLACK & YELLOW WIRES WHTIBLK. STRIPE

RED

HORIZ.-MOTION PCB: BLUE, RED, BLACK BLACK & VIOLET WIRES

Figure 10 Opening the Control Panel and Replacing Switches

A. Cleaning B. Fuse Replacement

This game contains six fuses—all on the power “SS

supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 22 of this manual. See the color monitor manual for the monitor fuse data.

C. The Control Panel

The exterior of the game cabinet and the metal and glass surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.

The large monitor shield and the attraction panel are made of tempered glass and should be scratch- Prior to repairing or replacing any switch or the resistant: if cleaned without abrasive substances, Mini-Trak Ball™ on the contro! panel, unplug the you should hardly ever have to replace them. game. Then open the coin door.

Page 27

Reach through the coin-door opening and open the luggage-style latches, located at each end on the underside of the control panel. Close the coin door. Lift up on the control panel at the topmost edge and tilt it toward you.

The control panel edge next to the monitor shield has foam tape applied to it. This tape acts as a cushion for the glass and prevents spilled liquids from entering the cabinet interior. Always make sure this tape is in good condition.

  • LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.
  • Remove the wires from the suspected switch.
  • Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter.
  • Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts).
  • Check contacts (push and release the switch button) for closed and open continuity.
  • If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
  • Leaf-Switch Replacement

The leaf switch on this game operates on 5 volts at a very low current. Therefore, pitting of the switch would be extremely rare. Probably the only reason that pitting would occur is that the game is in very high-humidity locations.

Don’t burnish the switch contacts. To clean them, use electrical contact cleaner.

To replace the switch, remove both of its screws with a Phillips-head screwdriver.

If the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The white ring on the outside of the control panel should not spin, due to its design.

NOTE Adjust switch for a narrow gap. Whena switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.
  • Mini-Trak Ball™ Maintenance and Repair

To maintain this control, lubricate the bearings approximately every 3 months or every 6,000 credits. The number of credits can be read off the coin counter, located on the coin door. Use only 2 drops of 3-in-One® oil in each of the ball bearings. (Each Mini-Trak Ball™ control has six bearings.)

For further instructions on how to replace the ball, either coupler PCB or either encoding wheel, see Figure 11. “SS

Page 28

Ball Replacement Coupler PCB and Encoding Wheel Replacement

  • First remove the entire Mini-Trak Ball™ assembly from the 3. Lift the PCB out of its slot. Carefully unplug the red connec: control panel as shown in Figure 11. Now locate the six toron the coupler PCB. “twin-lead” thread-forming screws in the black frames or 4. To replace either encoding wheel, remove the PCB from its plastic pleces; remove these six screws. slot. Remove the socket-head machine screw, flat washer, Lift off the top frame; remove and replace the ball. and split lock washer that secure the encoding wheel. Remove the wheel.
  • When replacing the coupler PCB, be certain that the black metal encoding wheel has not been bent or damaged. It should turn freely between the two halves of the red photosensor device.

To Tighten Encoder Wheel

  • Rotate socket-head screw on the end of the shaft until hole in the shaft is visible through the hole in the top of the frame.
  • Insert 7,-inch diameter pin or screwdriver through hole in shaft.
  • Tighten socket-head screw with an Allen wrench.

@ screworiver ‘OR PIN

LUBRICATE HERE © (6 PLACES) i

ENCODER WHEEL

@ socket-HEAD SCREW

HOLE IN SHAFT @) ALLEN WRENCH

SCREWDRIVER MAY BE INSERTED FROM BOTTOM

Disassemble in the order indicated. (Circled numbers match the steps described above.)

Figure 11 Mini-Trak Ball™ Maintenance and Repair

Page 29

D. Monitor

Kemoval

The following procedure should only be performed by a qualified service technician.

WARNING Shock Hazard High voltages may exist in any television or monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the yoke area with your hands or with metal objects in your hands! Implosion Hazard If you drop the monitor and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any monitor. To remove the color monitor, follow steps 1 thru 6 below. Refer to the accompanying Figure 12.
  • Be sure the game is unplugged from its wall outlet! Unlock and open the rear access panel, coin door, and control panel.
  • Remove the glass monitor shield. Carefully remove the four staples that secure the blue cardboard bezel. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube.
  • Standing at the rear opening of the game, locate the 2-pin and 6-pin harness connectors for the monitor. Unplug both of these.
  • At the bottom rear of the monitor chassis is a wood screw that secures rear part of the chassis. Remove this screw.
  • From the front of the cabinet, locate the flat washers, and self-locking hex nuts (two sets underneath, and two sets above the monitor screen). This hardware attaches the monitor to the cabinet. Remove this hardware.
  • Carefully pull the monitor chassis out of the cabinet towards you.

Disassemble in the order indicated. (Circled numbers match the steps above.)

Figure 12 Monitor Removal

Page 30

Printed-Circuit Board Kemoval

You may wish to remove the Centipede™ game printed circuit board (PCB) or the Regulator/Audio II PCB for service or inspection. To do this, refer to Figure 13 and proceed as follows: E.

  • Game PCB Removal @ Unlock and open the rear access panel. @ Remove the 24-pin and 44-pin edge connectors from the right side of the game PCB. @ Locate the Phillips-head screw that extends through the PCB and into the two wood blocks (at the right side of the board). Remove and save this screw, as well as the fiber spacers. @ Remove the PCB from the cabinet by carefully sliding it straight out of the plastic PCB retainer. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as necessary. After servicing, reinstall the PCB, making sure that the edge connectors are properly plugged in.
Note that the connectors are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your PCB and will void the warranty. Check that the operation of the game is correct by performing the self-test. It is especially important to do the self-test with any game when you replace a PCB.

Regulator/Audio Il PCB Removal Unlock and open the rear access panel. Remove the five plug-in connectors on the Regulator/Audio If PCB. Note that all of these connectors are keyed for proper orientation. Locate the two Phillips-head screws that extend through the PCB and into the wood behind the PCB. Remove and save these two screws and the two fiber spacers. Remove the PCB from the interior wall of the cabinet by lifting it up and out of the wood slot.

el

REGULATOR! AUDIO II PCB

GAME PCB

Figure 13 Printed-Circuit Board Removal

Page 31

Figure 14 Fluorescent Tube Replacement

F. Fluorescent

To replace speaker or the white fluorescent tube

Tube and behind the front graphics attraction panel, follow Sp e aker this procedure (see Figure 14) Replacement let. Remove the three Allen-head screws and lock

Sp e aker this procedure (see Figure 14).

  • Be sure the game is unplugged from its wall out-

washers at the top of the game (they secure the black metal retainer for the attraction panel). Lift the attraction panel up and out of its lower retainer.

  • If you need to replace the speaker, remove the
WARNING two Phillips screws that secure the light board If you drop a fluorescent tube and it breaks to the cabinet, and slide out the whole assembly. The fluorescent light and speaker harness has extra length, so you can pull the assembly about one foot out of the game. Unplug the harness connector just behind the board. it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.
Page 32
  • Remove the two plug-in connectors on the speaker. Remove the speaker from the wood board and replace it.
  • Toreplace the fluorescent tube, remove the grey cardboard locking tab at each end of the tube. Slightly rotate the tube up or down, and carefully remove it from the lampholders.
  • Replace with a new tube. Never force the tube into the lampholders—you may break it, causing an implosion!
  • Also check that the green ground wire is secure- OS™ ly attached to the large metal bracket and the ballast transformer behind the wood panel. If the lamp is not grounded, it may not start.
  • If you removed the light and speaker assembly, reconnect the harness connector, then reinstall the assembly. Replace the attraction panel on the front of the game.

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for the Centipede™ (upright) game. Sheet 1, Side A, includes a “table of contents” that shows the arrangement of these diagrams. They explain the functions of the circuits; the diagrams also define inputs and outputs.

Atari’s Centipede™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio Il PCB, loudspeaker, and control panel.

The Regulator/Audio || PCB performs two functions: 1) it regulates the + 10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio Il PCB provides most logic power to the game PCB. The audio output from the Regulator/- Audio II PCB directly drives the game speaker and is controlled by the volume control, mounted on the bracket inside the coin door.

The power supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power-supply chassis.

Figure 15 illustrates the distribution of power in this game. Figure 16 illustrates the distribution of signals. m

Page 33

FLUORESCENT TUBE

COLOR MONITOR

a . CONTROL PANEL \/

] ©. 2040

COIN DOOR

=] | INTERLOCK

SWITCHES 5

| GAME PCB

y = 3 ye -.\) re g g POWER SUPPLY S| 2 = s zg

Xr, Y AC POWER CORD % ‘es

e

REGULATOR! AUDIO II PCB

POWER ON/OFF SWITCH

Figure 15 Power Distribution

Page 34

Figure 16 Signal Distribution REGULATOR’ AUDIO II PCB COIN DOOR Q fo} z a 3° g sy z m fuk

‘START 1 LED ‘START ‘START2 LED ‘START?

TRAK BALL H DIR & CLK

TRAK BALL VDIR& CLK

COINL.GR,

‘SELF-TEST

SLAM

COIN COUNTLLGR LS} ‘SPEAKER 1 & 2 Coo AupI0 1&2 Aupio our

RED, GREEN, BLUE

COMP SYNC

a 4

VOLUME CONTROL

GAME PCB COLOR MONITOR SPEAKER

Page 35

Illustrated Parts Lists

This chapter provides you with the necessary information for ordering replacement parts for your Centipede™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598-thru approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 36

92.049 036498-01 “Ss Lia (Upper Retnr.) Fluor. Light & Spkr.— (Monitor) see Figure 23 037411-01 (Attract. Panel) 036495.01 (Spkr. Grille) 003053-01 (Lower Retnr.) 037413-01 (Mon. Shield)

Mini-Trak Ball— 037443-01 (Mon. Bezel) see Figure 19

71-2110 (Lock) Control Panel Assy.— see Figure 18

178013-001 (Latch)

037427-01 ‘ (Foam Pad) 19-9032 4 ; . (Vol. Ctrl.)

(Self-Test Sw.) { 030168-01 (rete 037419.02 (Rear Panel)

Coin Doors— see Figures 24, 25 03626201 (Coin Box Brkt.)

036686-01 (Game Pricing Labels— not shown for clarity) A035943-01, -02 or -03 (Coin Box) 035942-01 (Se 78-3201 (Separator) (Leg)

Figure 17 Cabinet-Mounted Assemblies A037397-xx G

Page 37

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe cific written permission of Atari, Inc., Sunnyvale, CA, This Schematics, Self-Test Label & Manuals— drawing is only conditionally issued, and neither receipt nor see parts list on following page possession thereof confers or transfers any right In, or li- Gense to use, the subject matter of the drawing or any de ‘sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except lor ‘manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereot unless by written agreement with or written permission from the corporation:

037399-01 (Cab't Assy.)

178034-024 (FMolding)

A037456-01 (Pwr. Harness)

035745.02 037443-02 (PCB Retnr.) (Coin Defictr)

034536-03 A037 460-01 (Vibra. Damper) (Interl. Sw./Brkt.)

Game PCB— 007882-02 7 nm (interl. Sw. Cvr.) see Figure

75-07017 (PCB Spacer)

78-24012 (PCB Tie Wrap)

, / ‘A037433-01 Reg/Audio I! PCB— _ > ‘see Figure 20 LL (Main Harness)

>. S ‘A037453-01, A037454-01 or ‘A037455-01 (Power Cord) 034536-02 (Vibra. Damper)

Power Supply Assy.— see Figure 22 037243-01 (Plate)

‘A037470-01 (On/Off Sw./Mtg, Plate) 00999201 (On/Off Sw. Cvr.)

Figure 17 Cabinet-Mounted Assemblies A037397-xx G

Page 38

Figure 17 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description A035943-01 Deep-Well Coin Box Assembly {for all the same coins) A035943-02 Deep-Well Coin Box Assembly (for two different coin denominations—has one separator) A035943-03 Deep-Well Coin Box Assembly (for three different coin denominations—has two separators) A037433-01 Main Harness Assembly SSS

A037450-01Interlock Switch/Bracket Assembly(modified for safety)
A037453-01Strain-Relief Power Cord(U.S.)
A037454-01Strain-Relief Power Cord(Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece,

Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)

A037455-01Strain-Relief Power Cord(Australia and New Zealand)

A037456-01 Power Harness Assembly A037470-01 Power On/Off Switch/Mounting Plate Assembly The following seven items are the technical information supplements to this game: DP-182-01 Centipede™ (Upright) Schematic Drawings (Sheet 1)

DP-182-02Centipede Schematic Drawings(Sheet 2)

ST-182 Centipede Label with Self-Test Procedure and Option Switch Settings TM-160. Instruction and Service Manual for 19-Inch Electrohome Color Monitor, or TM-201 Instruction and Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Monitor TM-182 Centipede Operation, Maintenance and Service Manual TM-192, Centipede Signature Analysis Guide 19-9032 Volume Control 69-001 DPOT Self-Test Switch (for British-made coin doors)

71-2110Panel Cartridge Lock Mechanism(for rear access panel)

7507017 Spacer for Mounting Printed Circuit Boards

78-24012§-Inch Beaded Nylon Tie Wrap(for game PCB edge connectors)

78-3201 Cabinet-Leveling Leg 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, %-Inch Thick x ¥%-Inch Wide (2 x 24 in. req’d.) 92-049 19-Inch Electrohome Color Raster-Scan Monitor, or 92-055 19-Inch Wells-Gardner Color Raster-Scan Monitor 003053-01 Lower Attraction-Panel Retainer 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover

030168-01Volume Control Mounting Bracket(also holds self-test switch in games with British-made

coin doors) 034536-02 Foam Vibration Damper (for Regulator/Audio Il PCB) 034536-03 Foam Vibration Damper (for Centipede game PCB) 035745-02 18-Inch Plastic PCB Retainer 035942-01 Deep-Well Coin Box Separator 036262-01 Coin Box Bracket 036495-01 Speaker Grille 036498-01 Upper Attraction-Panel Retainer 036686-01 Card of Game Pricing Labels 037243-01 Metal Base Plate (located underneath power supply) 037399-01 Cabinet Assembly (includes legs and PCB retainers, but not the rear access panel) 037411-01 Attraction Panel with Graphics 037413-01 Monitor Shield with Graphics 037419-02 Rear Access Panel (does not include lock) 037427-01 Rear Access Panel Foam Pad 037443-01 Blue Cardboard Monitor Bezel “a 037443-02 Cardboard Coin Deflector 178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding

Page 39

aN Mini-Trak Ball Assy.— 78-6900402 see Figure 19 (Foam Tape)

CAUTION Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the contro! panel. Only then should you lock up the game. 75.9810NO (Stamped Nut) 160013-001 (Leaf Sw. Button Holder) — 178030-001 (Pushbtn. Assy.)

A037408-01 (Ctrl. Pr.) Pere (Sw. Bezel)

A037435-01 (Harness)

037406-01 (Control Pn.) (Ctrl. Pri. Assy.) 037407-01 (Cont. Pni. Decal) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This <rawing is only conditionally issued, and neither receipt nor 62.039 possession thereof confers or transfers any right in, oF lit Eense to use, the subject matter of the drawing or any de- (LED Switch) sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture Under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereo!, unless by written agreement with or written permission from the corporation’ Figure 18 Control Panel Assembly A037409-01 D Parts List

Part No. Description

A037408-01 Control Panel with Graphics Decal A037435-01 Control-Panel Harness 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 75-9910NO #5,-11 Steel Stamped Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, ‘4-inch wide x %-inch thick (24 in. required) 036895-01 Black Molded Switch Bezel 037406-01 Control Panel 037407-01 Control Panel Decal 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-001 Pushbutton Assembly

Page 40

176010-106 —F NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF li Cense to use, the subject matter of the drawing or any de- (6 PLACES) I Sigh or technical information shown thereon, nor any right (Screw) to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereot, unless by written agreement with or written permission from the corporation.

036191-01 (Upper Frame) AN I

035936-01 (Ball)

036193-01 1 035937-01 (idler rat (Ball Bearing)

035931-01 (Roiler Shaft)

035938-01 (Wheel)

75.0148. (2 PLACES) (Washer)

(2 PLACES) ; (Washer) a Places) 7% yt ; 030369-01 (Opt'l. Coupler— hidden from view) A036096-01 (Harness) (Screw)

036192.01 (Lower Frame)

034168-01 (Label—not shown for clarity) (Coupler PCB)

Figure 19 Mini-Trak Ball™ Assembly A036190-01 A

Page 41

Figure 19 Mini-Trak Ball™ Assembly Parts List “SS

Part No. Description A035220-02 Coupler PCB Assembly (includes Radial Optical Coupler) A036096-01 Harness Assembly 72-8406 #4-40 x %-Inch Hex Socket-Head Cap Alloy Steel Machine Screw 75-0148 #4 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-044S #4 Zinc-Plated Steel Split Lock Washer 030369-01 Radial Optical Coupler (located on Coupler PCB Assy.) 034168-01 Label with Lubrication Instructions

035931-01Roller Shaft(2 per assembly)

035936-01 Mini-Trak Ball™

035937-01Ball Bearing(6 per assembly)

035938-01 Etched Encoding Wheel 036191-01 Upper Black Plastic Frame 036192-01 Lower Black Plastic Frame

036193-01Idler Shaft(1 per assembly)

176010-106 #8 x %-Inch Cross-Recessed Pan-Head Thread-Forming Twin-Lead Zinc-Plated Steel Screw

Page 42
Scan of page 42

This page is a drawing, shown as the original scan.

Page 43

Figure 20 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

19-100P1015.1 Ohm, +3%, 7W Wirewound Resistor(R24)
19-3151021K Ohm Vertical PCB-Mounting Cermet Trimpot(R8) Acceptable substitute is part no.

119002-102.

24-2501081000 yf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)
24-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C1, 4, 12)
24-350226,22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor(C24, 31)
24-3503383300 pf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor(C9, 10, 18, 19)

24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23)

29-088-1 uf Ceramic-Disc 25V Radial-Lead Capacitor(C3, 11, 20, 21)
31-1N4002100V 1-Amp. Silicon Rectifier Type 1N4002 Diode(CRI, 4)
31-1N5401100V 3-Amp. Silicon Rectifier Type 1N5401 Diode(CR5¢8)

33-TIP32 PNP Power Transistor, Type TIP32_(Q2)

34-2N3055NPN Silicon Transistor, Type 2N3055(Q3)
37-LM3055V Linear Voltage Regulator(Q1)
37-7812+12V Voltage Regulator, Type 7812(Q8)
37-7905—5V Voltage Regulator, Type 7905(Q9)

72-1608C #6-32 x ‘%-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 72-6606S #6 x 3-Inch Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Plated-Steel Screw (Q8)

75-F60405,#6-32 x ¥4-Inch Binder-Head Nylon Screw(Q5, 7)

75-99516 #6-32 Nut/Washer Assembly

78-16008Thermally Conductive Compound(Q3)

78-16014 Thermally Conductive Silicon Insulator (Q2, 9)

79-583066-Position Connector Receptacle(J6, 9)
79-58308.9-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacle(J8)

034531-01 Heat Sink

100015-103.01 pf Ceramic-Disc 25V Radial-Lead Capacitor(C5, C14)
110000-0101 Ohm, +5%, %W Resistor(R10, 19)
110000-10010 Ohm, +5%, %W Resistor(R11, 20, 29, 30)
110000-101100 Ohm, +5%, %4W Resistor(R4, 12, 22)
110000-1021K Ohm, +5%, %4W Resistor(R27, 28)
110000-10310K Ohm, +5%, %W Resistor(R13, 14)

110000-271 270 Ohm, +5%, %4W Resistor (R1)

110000-33033 Ohm, +5%, %4W Resistor(R3)
110000-3923.9K Ohm, +5%, VW Resistor(R6)
110000-5625.6K Ohm, +5%, YW Resistor(R32, 33)
110000-7527.5K Ohm, +5%, %4W Resistor(R7)

110001-221 220 Ohm, +5%, /2W Resistor (R9, 21)

110009-0272.7 Ohm, +5%, 1W Resistor(R5)
116000-22022 Ohm, +5%, 10W Wirewound Resistor(R31)
116001-0404 Ohm, +5%, 5W Wirewound Resistor(R25)

122002-102 .001 pf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C2, 7, 16)

122004-224.22 uf Ceramic-Disc 25V Capacitor(C6, 8, 15, 17)
137151-002Type-TDA2002A 8W Linear Audio Amplifier Integrated Circuit(Q5, 7)

179051-001 Test Point Acceptable substitute is part no. 020670-01.

Page 44

Fig A037241-01 ure 21 Centipede™ Game PCB Assembly H SH —— a —

HR ae

Page 45

Figure 21 Centipede™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 01229401 Audio I/O N-Channel MOS/LSI Custom Chip (C3) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C83) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C52, 78) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C79-82, 84, 86, 90, 94-97, 100, 105-108) 24-500106 10 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C85) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 5-37, 40-51, 54-64, 66-77, 87, 88) 31-1N914 75V Type-1N914 Switching Diode (CR1, 2) 31-1N4001 75V Type-1N4001 Switching Diode (CR4, 5) 33-2N3906 Type-2N3906 PNP Switching and Amplifying Transistor (Q3) 34-2N3904 Type-2N3904 NPN Silicon Transistor (Q1, 2, 4, 5) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q6-8) 37-LM324 Type-LM324 Integrated Circuit (K10) 37-4584B Type-4584B CMOS Integrated Circuit (E/F10, E/F11) 37-555 Type-555 Timer Integrated Circuit (A11) 37-74LS00 Type-74LS00 Integrated Circuit (L8) 37-74LS04 Type-74LS04 Integrated Circuit (K3) 37-74LS08 Type-74LS08 Integrated Circuit (B7, K4) 37-74LS10 Type-74LS10 Integrated Circuit (L3, K2) 37-74LS20 Type-74LS20 Integrated Circuit (A7) 37-74LS32 Type-74LS32 Integrated Circuit (A4, C5, E3, F3, J3) 37-74LS42 Type-74LS42 Integrated Circuit (H3) 37-74LS74 Type-74LS74 Integrated Circuit (D4, D11, M3) 37-74LS83 Type-74LS83 Integrated Circuit (F6, H6) 37-74LS86 Type-74LS86 Integrated Circuit (E7) 37-74LS90 Type-74LS90 Integrated Circuit (L2) 37-74LS139 Type-74LS139 Integrated Circuit (C4, J2) 37-74LS153 Type-74LS153 Integrated Circuit (C7, E8, K6, L6, M6, N6, P6) 37-74LS157 Type-74LS157 Integrated Circuit (D7, D8, D/E11, F8, H8, J8, K8, P5) 37-74LS 163A, Type-74LS163A Integrated Circuit (A5, B5, M2, N2, N3, P2, P3) 37-74LS 166 Type-74LS166 Integrated Circuit (H9, J9) 37-74LS174 Type-74LS174 Integrated Circuit (C6, D6, E6, J4) 37-74LS175 Type-74LS175 Integrated Circuit (A8, E4, M4, N4) 37-74LS191 Type-74LS191 Integrated Circuit (B11, C11) 37-74LS244 Type-74LS244 Integrated Circuit (B1, C1, H5) 37-74LS245, Type-74LS245 Integrated Circuit 37-74LS257 Type-74LS257 Integrated Circuit (D9, D/E10, K9, L9, P7, M8, M9) 37-74LS259 Type-74LS259 Integrated Circuit (M10) 37-74LS273 Type-74LS273 Integrated Circuit (B4, J6) 37-74LS373 Type-74LS373 Integrated Circuit (J5) 37-74LS374 Type-74LS374 Integrated Circuit (H4) 37-74S04 Type-74S04 Integrated Circuit (N1) 37-74S74 Type-74S74 Integrated Circuit (E9, F9) 37-7407 Type-7407 Integrated Circuit (A9, A/B10) 37-7815 + 15V Voltage Regulator (VR2) 37-7915 -15V Voltage Regulator (VR1) 38-MV5053 Type-MV5053 Light-Emitting Diode (CR3) [Continued on next page]

Page 46

Figure 21 Centipede™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 41-3003 100 UH, +5%, Hot-Molded Plastic Fixed R.F. Choke (L1-3) Acceptable substitute is part no. 141002-001.

62-001SPST Momentary Pushbutton Switch(Reset)

66-114P1T 4-Station, Single-Throw, Dual-Inline-Package Bit Switch (N11) 66-118P1T 8-Station, Single-Throw, Dual-Inline-Package Bit Switch (N8, N9)

79-42C1616-Contact Medium-Insertion-Force Integrated Circuit Socket(P4)
79-42C2222-Contact Medium-Insertion-Force Integrated Circuit Socket(E5)
79-42C2424-Contact Medium-Insertion-Force Integrated Circuit Socket(F7, H/J7, D1, E1, F/H1, J1)
79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(C2, C3)

81-4302 Nylon Snap-In Fastener

90-10212.096 MHz +.005%, Crystal(Y1) Acceptable substitute is part no. 144000-001.

90-6013 Microprocessor 6502A (C2)

90-7005Random-Access Memory(C8)
90-7018Random-Access Memory(K5, K7, L5, L7, M5, M7, N5, N7)
90-7033Random-Access Memory(F2, H2)
110000-1021K Ohm, +5%, %W Resistor(R9-11, 13-16, 23-28, 31-36, 55-60, 67, 68, 77, 79, 80, 87-89,

94, 95, 99, 104, 109, 114-123, 134, 136-141, 148, 149)

110000-10310K Ohm, +5%, %W Resistor(R1, 2, 6-8, 12, 17-22, 29, 30, 37-54, 70, 71, 83-86,

130-133, 147, 150, 155, 156)

110000-104110K Ohm, +5%, YW Resistor(R81, 82, 105, 106)
110000-105100 MegOhm, +5%, %4W Resistor(R5)

110000-152 1.5K Ohm, +5%, %4W Resistor (R108)

110000-221220 Ohm, +5%, YW Resistor(R3, 62, 64, 66, 72, 74-76, 78, 135)

110000-222 2.2K Ohm, +5%, Y4W Resistor (R107)

110000-331330 Ohm, +5%, %4W Resistor(R61, 63, 65)

110000-332 3.3K Ohm, +5%, Y%4W Resistor (R69, 143-146, 151-154)

110000-471470 Ohm, +5%, %4W Resistor(R90-93, 96-98, 100, 110-113, 124-129, 142)
110000-56056 Ohm, +5%, %W Resistor(R101, 102)
110000-56356K Ohm, +5%, %4W Resistor(R4)
122002-102.001 pf Ceramic-Disc 50V Radial-Lead Capacitor(C4)
122004-224.22 uf Ceramic-Disc 25V Radial-Lead Capacitor(C65)
122005-103.01 pf Ceramic-Disc 25V Radial-Lead Capacitor(C53)

128002-101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C1) 4128002-102 1000 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C98, 99) 128002-390 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C2) 128002-470 47 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C38, 39) 136001-201 or -211 136001-202 or -212 136001-303 or -307

136001-304 or -308 136001-305 or -309 136001-306 or -310 136001-213

137161-001

137169-001 137170-001 179051-001 Read-Only Memory Read-Only Memory (H/J7) Read-Only Memory (D1)

Read-Only Memory (E1) Read-Only Memory (F/H1) Read-Only Memory (J1) Programmable Read-Only Memory (P4)

Type-ER2055 Integrated Circuit(E5)Note: /f you replace this part, you must erase this ROM

before locking up the game. See Figure 7, Self-Test Procedure, in this manual for instructions. Type-74LS107 Integrated Circuit (L4)

Random-Access Memory(A6, B6)Acceptable substitute is part no. 90-7035.

Test Points Acceptable substitute is part no. 020670-01.

Page 47

79-4411001 (Fuse Post) 03448202 037639-01 46-2017002 034544-01 46-2014002 037641-01 a (Chassis) (Label) (Fuse) (Cover) (Fuses) (Label) 79-3206 (Fuse Block)

A035891-01 (Fuse Harness)

78-2708 TOP VIEW (Hole Bushing)

Picea ALL PERSONS RecennG. THIS OPAWING ‘A037671-01 power supply assembly has 120V plug 78-70501SC ZONFIDENTIAL: Reproduction forbidden without the spe ‘A037671-02 has the 100V, 220V and 240V plugs (Capac. Bracket) Srawing s only Conditionally issued, and neither receipt nor ‘A037671-03 has the 220V and 240V plugs 29.053 possession thereot conters or transfers any right in, or I- Gense to use, he subject matter of the drawing or any de (Capacitor) sign or technical information shown thereon, nor any right, to reproduce this drawing or any part thereof. Except for manutacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter hereo!,un- A035888-01 Tess by written agreement with or written permission from (Transtormer) the corporation.

BOTTOM VIEW

(GG

3A-MDA3501 (Rectifier)

A034630-01 A035890-01 A034629-01 79-15021001 (RFI Filter) (Pwr. Harness) (AC. Harness) (Term’! Block)

Figure 22 Power Supply Assembly A037671-xx c

Page 48

Figure 22 Power Supply Assembly ASS Parts List

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100V(violet)
A021084-02Voltage Plug for 120V(yellow)
A021084-04Voltage Plug for 220V(blue)
A021084-05,Voltage Plug for 240V(brown)

A034629-01 AC. Harness Assembly

A034630-01RFI Filter Assembly(FL1)
A035888-01Transformer Assembly(11) Acceptable substitute is part no. A035888-02

A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly 29-053, 27,000 uf 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140024-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-301203,20-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%,-Inch Outside Diameter x Ya-Inch Thick 78-70501SC 21nch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover

037639-01Label for Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)
Page 49

a

179035-001 (Lampholder) 79-561816P (Starter) (Socket) 148001-001 (Wire Nut)

NOTE To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to both the ballast transformer and the steel lamp bracket. 99-11003 99-11009

(Speaker)

A037457-01 (Harness)

142028-xxx (Transformer)

037469-01 pad (Bracket) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe- Gific written permission of Atari, Inc., Sunnyvale, CA. This Srawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or li- Eense to use, the subject matter of the drawing or any deteprosuce ths drawing or any pat inereo. Except for ‘A037540.01 mantacture by vendors ot Ata ic, and for manutacture (Tab) . tose by written agreement with or witten permission from ‘the corporation.

Figure 23 Fluorescent Light and Speaker Assembly A037417-01 and -02 E

Parts List

Part No. Description

A037457-01 Light and Speaker Harness A037540-01 Ground Wire with Ring Lug 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 79-561816P Spring-Connector Wire Nut for 16- to 18-Guage Wires

99-11003 Fluorescent Lamp Starter 99-11006 Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Lamp Bracket 142028-001 60-Hz 118-Volt Ballast Transformer (used on A037417-01 assembly) 142028-002 50-Hz 118-Volt Ballast Transformer (used on A037417-02 assembly) 148001-001 6x9-Inch 4-Ohm 15-Watt Oval High-Fidelity Speaker 179035-001 2-Pin Fluorescent Lampholder

Page 50

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 51

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-10103 CONFIDENTIAL: Reproduction forbidden, without the (inner Pri Specific written permission of Atari, Inc., Sunnyvale, CA {his drawing is, only conditionally’ issued, and neither wiLevers) S receipt nor possession thereof confers or transfers any 75-948: fightin, or ligense to use, the subject matter of the drawing 99-10096 (Hex Nut) ao-10008 for any design or technical information shown thereon, nor (Fastener) ees (Self-Test Sw.) 99-10052 ny right to reproduce this drawing or any part thereof. Ex-

(Lever) 2 cept for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing Is granted or the subject matter thereof unless by written agreement with or written permission from the corporation. 99-10071 : (Slam Sw.) ~~ 98-10073 a (Decal)

75-1408S (Screw) . Part of 99-10095

75-9448 99.10096 (Hex Nut) (Fastener)

99-10063 (Coin Chute) 99-10097 99-10040 (Insut.) (Coin inlet Chute) | 99-10101 (Coin Chute)

70-11-47 (Lamp),

99-10080 (Lamp Socket)

99-10104 (Bar Retnr.)

99-10041 (Coin Counter)

99-10105, (Bar) 99-10081 (Key Holder) TAA2KXxx , (Coin Mech.) ~

;/75-9448

(Hex Nut)

‘(Coin Sw.)72.9603S

COIN RE) (Return Box) 29608

——99-1075 thruS99-1047
ini)99-10078(Lockt. Coil)

(Sw. Wire) 31-1N4002—Part 99-10042 thru “ANAOD2—F

99-1004599-100086-100

(Coin Sw. Assy.) (Retainer) 75-1412S, 99-10082 (Screw) (Cover) Figure 24 American-Made Coin Door 71-10xxxx D

Page 52

99-10012 thru 99-1002, and 99-10107 (Button Assy.)

99-10062 (Button) 99-1000 or 99-10010 00 < (Door) D> 99-10094 (Insul.)

Part of 99-10074

99-10049 (Locking Arm)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvate, CA. This ‘drawing is only conditionally issued, and neither receipt nor jon thereof conters or transfers any right in, or liccense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture ‘under the corporation's written license, no right to repro- ‘duce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

71-102201 — U.S. 25/25¢ Coin Door 74-103202 — U.S. 26¢/25¢/25¢ Coin Door 71-103203 — U.S. 25¢/25¢/$1 Coin Door 74-102204 — German 2 DM/1 DM Coin Door 71-103205 — German 1/2/5 DM Coin Door 99-10055 thru 99-10059 (Button Cover)

99-10074 99-10070, 99-10083 (Lock) thru 99-10092, and 99-10108 (Price Plate)

75-9188. (Hex Nut)

75-915S. (Hex Nut)

'99-10051 (Frame)

71102206 — German 1 DM/5 DM Coin Door 71-102207 — Belgian § Fri Fr Coin Door 71-102208 — Swiss 1 Fr!1 Fr Coin Door 71-102209 — Japanese 1007/100Y Coin Door 71-102210 — British 10 P10 P Coin Door 72-JA1405B (Screw) 99-1054 (Btn. Housing) 72-HA1404C (Screw)

99-10061 (Bezel)

72-JA1405B (Screw)

99-10048 (Harness—not shown for clarity)

71-102211 — Australian 20/20¢ Coin Door 71-102212 — Itallan 100 1/100 L Coin Door 71-102213 — U.S. 500/50¢ (2 x 25%) Coin Door 71-103214 — U.S, 50¢/50¢/50¢ Coin Door 71-103215 — U.S. 50°/50¢/$1 Coin Door

Figure 24 American-Made Coin Door 71-10XXxx D

Page 53

Figure 24 American-Made Coin Door, continued Parts List

Part No. Description 31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-Usage Low-Force Miniature Switch 70-11-47 Miniature Bayonet-Base Incandescent Lamp, Type #47 71-1201ADU U.S. $1.00 Coin Mechanism 71-1201FCH Swiss 1 Fr Coin Mechanism 71-1201MG German 1 DM Coin Mechanism 71-1202MG German 2 DM Coin Mechanism 71-1205FB Belgian 5 Fr Coin Mechanism 71-1205MG German 5 DM Coin Mechanism 71-1210PE U.K. 10 P Coin Mechanism 71-1220CA Australian 20¢ Coin Mechanism 71-1225CU U.S. 25¢ Coin Mechanism 71-12100LI Italian 100 Lire Coin Mechanism 71-12100YN Japanese Y100 Coin Mechanism 72-HA1404C #4 x Y4-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Taptite” Cadmium-Plated Screw 72-JA1405B #4 x %.Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Plastite” Black Screw 72-9406S #4-40 x %Inch Slotted Trusz- Head Steel Machine Screw 72-9603S, #6-32 x ¥-[Inch Slotted Truss-Head Steel Machine Screw 75-915S #%4-20 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-9188 #8-32 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-944S #4-40 Polymer Self-Locking Steel Hex Nut 75-948S, #8-32 Polymer Self-Locking Steel Hex Nut 75-1408S #4-40 x ¥2-Inch Slotted Pan-Head Steel Machine Screw 75-1412S #4-40 x 34-Inch Slotted Pan-Head Steel Machine Screw 75-5520B #%/-20 x 1%-Inch Round-Head Square-Neck Steel Bolt with Black Finish 99-10008 Switch Wire Retainer 99-10009 2-Mech Coin Door Only 99-10010 3-Mech Coin Door Only 99-10012 U.S. 25¢ Coin Return Button Assembly 99-10013 U.S. $1.00 Coin Return Button Assembly 99-10014 German 1 DM Coin Return Button Assembly 99-10015 German 2 DM Coin Return Button Assembly 99-10016 German 5 DM Coin Return Button Assembly 99-10017 Belgian 5 Fr Coin Return Button Assembly 99-10018 Swiss 1 Fr Coin Return Button Assembly 99-10019 Japanese Y100 Coin Return Button Assembly 99-10020 U.K. 10 P Coin Return Button Assembly 99-10021 Australian 20¢ Coin Return Button Assembly 99-10022 Italian 100 Lire Coin Return Button Assembly 99-10040 Coin Inlet Chute Assembly 99-10041 Coin Counter Assembly 99-10042 Coin Switch Assembly for U.S. 25¢ and Belgian 5 Fr Coins (silver wire)

99-10043Coin Switch Assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 Coins(black wire)
99-10044Coin Switch Assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins(gold wire)
99-10045Coin Switch Assembly for German 5 DM, U.K. 10 P, and Australian 20¢ Coins(green wire)

99-10047 Lockout Coin Assembly 99-10048 Coin Door Harness Assembly

Page 54

Figure 24 American-Made Coin Door, continued Parts List

Part No. Description 99-10049 Locking Arm Assembly 99-10051 Coin Door Frame 99-10052 Coin Return Lever 99-10054 Coin Button Housing 99-10055 Coin Return Button Cover for Japanese 100Y Coin 99-10056 Coin Return Button Cover for German 1 DM and Swiss 1 Fr Coins 99-10057 Coin Return Button Cover for U.S. 25¢ and Belgian 5 Fr Coins 99-10058 Coin Return Button Cover for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins 99-10059 Coin Return Button Cover for German 5 DM, U.K. 10 P, and Australian 20¢ Coins 99-10061 Coin Return Bezel 99-10062 Coin Return Button 99-10063 Right Half of Coin Inlet Chute 99-10065 Coin Return Box 99-10066 Coin Return Cover 99-10068 Coin Chute 99-10070 U.S. 25¢ Price Plate 99-10071 Slam Switch Assembly 99-10073 Test Switch Decal 99-10074 Lock Assembly 99-10075 Black Switch Wire for German 1 DM, Swiss 1 Fr and Japanese 100Y Coins 99-10076 Silver Switch Wire for U.S. 25¢ and Belgian 5 Fr Coins 99-10077 Gold Switch Wire for U.S. $1.00, German 2 DM and Italian 100 Lire Coins 99-10078 Green Switch Wire for German 5 DM, U.K. 10 P and Australian 20¢ Coins 99-10080 Miniature Bayonet-Base Lamp Socket 99-10081 Wire Key Holder 99-10082 Switch Cover 99-10083 U.S. $1.00 Price Plate 99-10084 German 1 DM Price Plate 99-10085 German 2 DM Price Plate 99-10086 German 5 DM Price Plate 99-10087 Belgian 5 Fr Price Plate 99-10088 Swiss 1 Fr Price Plate 99-10089 Japanese Y100 Price Plate 99-10090 U.K. 10 P Price Plate 99-10091 Australian 20¢ Price Plate 99-10092 Italian 100 Lire Price Plate 99-10094 Fish Paper Insulation 99-10095, Toggle Switch 99-10096 “U"-Type Fastener 99-10097 Fish Paper Insulation 99-10101 Left Half of Coin Inlet Chute 99-10102 Switch and Lockout Coil Bracket Sub-Assembly 99-10103 Inner Panel with Levers Sub-Assembly 99-10104 Anti-Penny-Flip Bar Retainer 99-10105 Anti-Penny-Flip Bar 99-10107 U.S. 50¢ Coin Return Button Assembly (for two quarters) 99-10108 U.S. 50¢ Price Plate (for two quarters)

Page 55

99-15038 (Bezel for Button)

99-15001 thru 99-15012 (Ret. Button)

99-15052 (Spring for Button)

99-15051 (Lamp Holder)

99-15056 (Screw for Bezel) 99-15040 (Lever) ea “ (Coin Inlet)

9915025 ——», = (Coin Inlet) O a (erat er cove) a jezel for Cover PART OF a 99-15036 99-15041 - (Cover) a 99-15054 99-1041 (Pivot for Lever) 99-15055 . (Retng. Screw a7 (Lockout Coil) { 99-15053 (Lockt. Coil Spring)

99-15027 (Coin Ret. Box)

+ 99-15028 (Coin Ret. Box)

99-15037 (Sw. Adjuster) 99-15056 (Screw for Bezel) 99-15060 a (Sw. Cover) 99-15029 (Bracket)

(Switch)

Figure 25 British-Made Coin Door 171001-xxx A

Page 56

99-15067 (Lock Assy.)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing 1s only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or li- ‘cense to use, the subject matter of the drawing or any de ssign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for ‘manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to repro: duce this drawing is granted or the subject matter thereot uniess by written agreement with or written permission trom the corporation.

99-15064' (Frame)

171001-001 — British 10 P/10 P Coin Door 171001-002 — British 10 P/50 P Coin Door 171001-003 — British 20 P/50 P Coin Door 171001-004 — German 1 DM/1 DM Coin Door 171001-005 — German 2 DM/1 DM Coin Door 47-1002 (Counter)

171001-006 — German 2 DM/5 DM Coin Door 171001.007 — Belgian 5 Fr/5 Fr Coin Door 171001.008 — French 1 Fri1 Fr Coin Door 171001-009 — French 2 Fr/1 Fr Coin Door 171001-010 — Swedish 1 Kr/1 Kr Coin Door 99-15067 (Lock Assy.)

99-15063 (Screw)

99-15062 (Hinge)

99-15066 (Screw) 99-15065 (Clamp)

171001011 — Hong Kong $1/$1 Coin Door 171001-012 — Canadian 25%/25¢ Coin Door 171001013 — U.S. 25¢/25¢ Coin Door 171001-014 — Spanish 25 Pts/25 Pts Coin Door 171001-015 — Swiss 1 Frit Fr Goin Door

Figure 25 _British-Made Coin Door 171001-xxx A

Page 57

Figure 25 _British-Made Coin Door, continued 171001-xxx A

Part No. Description 47-1002 Coin Counter 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25%) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055, Retaining Screw. 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15061 Dual-Entry Door 99-15062 Hinge 99-15063 Screw for Hinge 99-15064 Coin Door Frame 99-15065, Clamp for Frame 99-15066 Screw for Frame 99-15067 Lock Assembly

Page 58

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted,

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Sellers’ plant: and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, ioss of use, incidental or consequential damages

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order. Fe SAL SAL SAE SL ST SE The use of any non-Atari parts may void your warranty, according to the terms of the warranty The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may seil parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor

This document is and contains confidential trade secret information of Atari, Inc

This document is loaned under confidential custody for the sole purpose of operation. maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever. and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used. or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 59

ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 ¢ TELEX 35-7488

QD + Wares Communications Company