CATHODE RAY TOMES

Atari 5200 Field Service Manual

Atari 5200 (Atari, 1982) · Service Manual · 181 pages · 58 sections · original scan

Page 1

CX 5200™

FIELD SERVICE

: MANUAL

ATARI ord © + Wve: communications Company July 1983

Page 2

COPYRIGHT () 1983 BY ATARI, INC. ALL RIGHTS RESERVED.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from ATARI, Inc.

Published By: ATARI, INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086

Page 3

EC.R. NO. 9936 ATARI, INC. ~ | Consumer Product Service ENGINEERING CHANGE REQUEST 845 W. Maude Avenue AT @ Sunnyvale, CA 94041 DATE REQUESTER PART NO. Wave ATARI om~ 6/21/83] S. Doyle FD100127 04 BASOifion Of SPort Model PART TOO ESM

JESCRIPTION OF CHANGE:

Replace the cover.

Replace the Table of Contents, pages iii and v.

Replace the Introduction, page vi.

Replace pages 1-1, 1-3, 1-7.

Replace page 3-1.

Insert the folded, oversize 2-PORT 5200 Schematics and Silkscreen, pages 2-19 through 2-29, into SECTION 2.

Insert SECTION 3A, 2-PORT MODEL 5200 TESTING, pages 3A-1, through 3A-9, after SECTION 3.

Replace page 4-1.

Insert SECTION 4A, 2-PORT 5200 DIAGNOSTIC FLOWCHART, pages 4A-1 through 4A-23.

Replace page 5-1.

Insert SECTION 5A, 2-PORT 5200 SYMPTOM CHECKLIST, page 5A-1.

Replace SECTION 6 with pages 6-1 through 6-13.

Replace SECTION 8 with pages 8-1 through 8-11.

Retain this ECN as a record of these changes.

ENGINEERING CHANGE REQUESTER= PLEASE COMPLETE ABOVE DOTTED LINE ---~--.----+-+----

  • ae — REASON FOR CHANGE DENIAL OR COMMENTS: NTEOL

PARTS DISPOSITION:

ENGINEERING CHANGE NOTICE HEN et ea a NO. ARE PRESENT THis EC.N. NO. 0036

Page 4

ATARI

ADVANCED VIDEO ENTERTAINMENT SYSTEM

MODEL 5200™

FIELD SERVICE MANUAL

Page 5

Atari believes that the information described in this manual is accurate and reliable, and much care has been taken in its preparation. However, no responsibility, financial or otherwise, shall be accepted for any consequences arising out of the use of this material. Information contained herein is subject to change. Revisions may be issued to advise of such changes and/or additions.

Correspondence regarding this document should be forwarded to Manager of Technical Support, Consumer Product Service, Atari Incorporated, 1272 Borregas, Sunnyvale, California 94086.

Page 6

TABLE OF CONTENTS

Section Title Page

INTRODUCTION vii

1 THEORY OF OPERATION 1-1

Overview 1-L Model 5200 Console 1-1 Four-Port Universal PCB differences 1-1 Two-Port Universal PCB differences 1-2 Outer Case 1-3 RF Shield 1-4 PC Board 1-4 Microprocessor Chip - MPU 1-4 Alphanumeric Television Interface Controller (ANTIC) 1-5 Graphic Television Interface Adaptor (GTIA) 1-6 Pot Keyboard Integrated Circuit (POKEY) 1-6 Switchbox 1-7 Game Controller 1-8

2 SILKSCREENS AND SCHEMATICS 2-1

3 4-PORT MODEL 5200 TESTING 3-1

Equipment Requirements 3-1 Testing with the Diagnostic Cartridge (Version 1.1) 3-1 Overview of Tests 3-1 Initialization 3-1 Power-up Screen 3-3 Solid (Black) Colored Screen or Vertically Lined Screen 3-3 Snowy Screen 3-4 Warped-Ragged Picture 4 Color Bar Test 3-4 Gray Bar Test 3-5 Any Video Screen 3-6 Pokey Adjust 3-7 Error Summary 3-8 RAM Test 3-10 Verify ROM 3-10 Port Test 3-10 Tone Test 3-10

CX5200 Field Service Manual iii Changed by ECN #0036 6/21/83

Page 7

Section

3A

4A

5A TABLE OF CONTENTS (Continued)

Title

2-PORT MODEL 5200 TESTING

Equipment Requirements Testing with the Diagnostic Cartridge (Version 1.1) Overview of Tests Initialization Power-Up Screen Solid Colored (Black) Screen or Vertically Lined Screen Snowy Screen Warped-Ragged Picture Color Bar Test Gray Bar Test Any Video Screen Verify OS ROM Tone Test POKEY (Port) Test RAM Test POKEY Adjust Test POKEY Softfire Test

4-PORT 5200 DIAGNOSTIC FLOWCHART

Overview The Swap-out Procedure Replace in Order ATARI Repair Hotline

2-PORT 5200 DIAGNOSTIC FLOWCHART

Swapout Procedure Replace In Order ATARI Repair Hotline

4-PORT 5200 SYMPTOM CHECKLIST

2-PORT 5200 SYMPTOM CHECKLIST

GAME CONTROLLERS Overview Joystick Key Pad Fire Buttons Select Buttons

CX5200 Field Service Manual iv

Page 8

TABLE OF CONTENTS

Section Title Page

Controller Testing 6-3 Controller Testing without a Model 5200 Console 6-5 Failures 6-6 POT Arm Alignment Procedure 6-8 Controller Disassembly/Assembly 6-10 CX52 Game Controller Schematic 6-13

7 CX53 Trakball 7-1

8 PARTS LIST 8-1

9 SERVICE BULLETINS 9-1

LIST OF ILLUSTRATIONS

Figure Title Page

L-1 Model 5200 Console 1-2 1-2 Channel 2-3 Switch and Future 1-3 Development Access 1-3 MPU Pin Assignments 1-4 1-4 ANTIC Pin Assignments 1-5 1-5 GTIA Pin Assignments 1-6 1-6 POKEY Pin Assignments 1-7

2-1 5200 Motherboard 2-3 2-2A 5200 Motherboard Schematic (A) 2-4 2-2B 5200 Motherboard Schematic (B) 2-4A 2-2C 5200 Motherboard Schematic (C) 2-4B 2-3 4-Port Silkscreen 2-5 2-4 4-Port Schematic (1 of 4) 2-7 2-4 4-Port Schematic (2 of 4) 2-9 2-4 4-Port Schematic (3 of 4) 2-11 2-4 4-Port Schematic (4 of 4) 2-13 2-5 Trakball Silkscreen 2-15 2-6 Trakball Keypad Schematic 2-15 2-7 Trakball Schematic 2-17 2-8 5200 2-Port Schematic (1 of 5) 2-19 2-9 5200 2-Port Schematic (2 of 5) 2-21 2-10 5200 2-Port Schematic (3 of 5) 2-23 2-11 5200 2-Port Schematic (4 of 5) 2-25 2-12 5200 2-Port Schematic (5 of 5) 2-27 2-13 5200 2-Port Silkscreen 2-29

CX5200 Field Service Manual v Changed by ECN #0036 6/21/83

Page 9

= ae u+

DADRARADN WONKDUFEYWNE

Sey yyy NDAUFUNE

Table

3-1

7-1 TABLE OF CONTENTS

LIST OF ILLUSTRATIONS

Title

Color Bars Screen Gray Bar Screen Any Video Screen Pokey Adjust Test Screen Error Summary

Color Bars Screen Gray Bar Screen Any Video Test Screen RAM Test Screen POKEY Adjust Test Screen

CX52 Game Controller Joystick Positions | & 2 Cable Connector Pins (End View) Pot & Arm Assembly Controller Top (Underside) Select Switch Bezel Removal Controller Knob Removal Pot Arm Positions for Assembly CX52 Game Controller Schematic

Top Cover Assembly Bottom Cover Assembly Trakball Block Diagram Diagonal or Circular Motion Cue Ball Support Top Cover (Underside) Main PC Board

LIST OF TABLES

Title

Diagnostic Error Codes

Game Controller Continuity Check

Keyboard Test Display

CX5200 Field Service Manual vi rie WonwWe DRANAKDAAD BG bee wero

in ine NNNOHDWN 0 ON

Page 10

INTRODUCTION

The Atari Advanced Video Entertainment System (Model 5200) Field Service Manual is a reference guide for you, the service technician.

This Field Service Manual is organized in twelve sections:

THEORY OF OPERATION - Overview of how the Model 5200 works and what its basic assemblies look like.

SILKSCREENS AND SCHEMATICS - Electrical drawings and layouts of all of the Model 5200 printed circuit boards.

4-PORT 5200 TESTING - Review of Diagnostic Tests available for diagnosing 4-Port Model 5200 problems.

2-PORT 5200 TESTING - Review of Diagnostic Tests available for diagnosing 2-Port Model 5200 problems.

4-PORT 5200 DIAGNOSTIC FLOWCHART - Aids for troubleshooting the 4- Port Model 5200.

2-PORT 5200 DIAGNOSTIC FLOWCHART - Aids for troubleshooting the 2- Port Model 5200.

4-PORT 5200 SYMPTOM CHECKLIST - Failure information to assist the experienced technician arrive at a rapid diagnosis of 4-Port Model 5200 problems.

2-PORT 5200 SYMPTOM CHECKLIST - Failure information to assist the experienced technician arrive at a rapid diagnosis of 2-Port Model 5200 problems.

GAME CONTROLLERS - Overview of hand controller construction with electrical schematics and recommended test and repair procedures.

TRAKBALL CONTROLLER - Overview of trakball construction with electrical schematics and recommended test and repair procedures.

PARTS LIST - Detailed breakdown of all parts used in the 4-Port and 2-Port models.

SERVICE BULLETINS - Section to be used to hold Field Change Orders, Upgrade Bulletins and Tech Tips.

This manual is designed for use by both the experienced and inexperienced service technician. The Diagnostic Flowcharts (Sections 4 and 4A) provide detailed procedures for technicians not completely familiar with the 5200 models. The Symptom Checklists (Sections 5 and 5A) provide a rapid reference for the more experienced technician.

CX5200 Field Service Manual vii Changed by ECN #0036 6/21/83

Page 11

SECTION 1

THEORY OF OPERATION

Overview

The ATARI Advanced Video Entertainment System (Model 5200) is an advanced microcomputer. It receives input from the game controllers, Read-Only-Memory (ROM) cartridges and other peripherals, and displays this input on a T.V. screen. A maximum of four players may play at one time.

The Model 5200 is composed of the console, switchbox and game controllers. The following paragraphs provide a general discussion of each of these items and their component parts. For a detailed discussion of the Game Controller see SECTION 6.

Model 5200 CONSOLE

The Model 5200 console is composed of an outer plastic case which houses the PC board and its RF Shield. Figure 1-1 shows the console and its parts.

There are currently three different PC Boards being used in Model 5200 consoles. Some models contain the original 4-port PC Board, number CA018087. Other consoles contain a 4-port universal PC Board, number CA020108. A third PC Board with only two player ports, number CA021374, is also available. Unless otherwise specified, the references in this manual pertain to the original 4~port PCB, number CA018087. The specific differences of the 4-port universal PCB and the 2-port universal PCB are called out below.

Four-Port Universal PCB differences:

External

The ATARI serial number on the bottom of the unit will have a + as its third designator. For example: CITE CODE DATE

AT +21 3 i 4-PORT DESIGNATOE Internal 8

  • The chip designators have been changed. A\ll chips are designated A instead of U.
  • Two 74LS244 ICs (U4 and UL5) were removed from the PC Board.
  • Two 74LS244 ICs (UL4 and U28) were replaced with a 74LS125 (Al4) and a 74LS51 (AL5).
  • Provisional circuitry for future expansion has been added in order to accommodate the VCSTM cartridge adaptor.

CX5200 Field Service Manual 1-1 Changed by ECN #0036 6/21/83

Page 12

Two-Port Universal PCB differences:

1)

2) 3) 4)

5)

Cartridge Socket Opening All of the 4-port universal board differences listed above are included on the 2-port universal PCB. Ports 3 and 4 and their associated discrete components have been removed. ICs Al2 and A13 have been removed. The automatic switchbox has been replaced with a manual switchbox and the RF cable has been replaced with the standard RF cable. The power adaptor plugs directly into the rear of the console instead of plugging into the switchbox.

RLF. Shield

PC Board

Figure 1-1. Model 5200 Console (4-PORT)

CX5200 Field Service Manual 1-2

Page 13

Outer Case

The outer case consists of a bottom and a top plastic cover which are held together by five Phillips-head screws.

At the rear of the bottom plastic cover (Figure 1-2) is:

  • an opening for access to the channel 2-3 switch
  • a removable door which allows access for future development.

In the base is a cable wrap post for RF cable storage.

[SE 9 Cat

4 LJ

Channel 2-3 Future Development Access

Figure 1-2. Channel 2-3 Switch and Future Development Access

The top plastic cover provides:

  • openings at the front for the four player ports
  • the power switch cover
  • the power ON/OFF switch
  • a storage area at the rear for two game controllers. The hinged cover for this area comes off as a separate piece when the top cover is disassembled.

RF Shield

An aluminum shield covers the PC Board and prevents the PC Board from generating interference on the T.V. screen.

CX5200 Field Service Manual 1-3 Changed by ECN #0036 6/21/83

Page 14

PC Board The console you are servicing may contain either the original PC Board Number CA018087 or the newer PC Boards Numbers CA020108 or CA021374. See Page 1-1 of this manual for an explanation of the three board's differences. The PC Board consists of: e 28 Integrated Circuit Chips on PC Board Number CA018087; 26 Integrated Circuit Chips on PC Board Number CA020108; 24 Integrated Circuit Chips on PC Board Number CA021 374, e a cartridge socket e an RF module e various discrete components The major chips on the PC Board are: Microprocessor Chip - MPU The microprocessor (MPU) is the brain of the 5200. It makes the major decisions based on information from the ROM cartridge and the Random Access Memory. Figure 1-3 shows the pin assignments for the MPU.

vss Ce o RES ROY C.: x» O $2 a Eis xO so rR Ce 77 A (IN) NG Els xT] Rw Nat Eis oO HALT YNC (= » 7 RW vec oe 3 oe ag oO 9 27 o1 Al O 6502 1 22 Az gd ua 30 [7] D3 aa Ow 2 De Ae oO» a os AS Oe 77 D6 6 Cs 2 07 a Ce 2a Als AS ov » FT Al4

  • Os 2 A13 Alo Ov 29 A12 ALL 2 af vss

Figure 1-3. MPU Pin Assignments

CX5200 Field Service Manual 1-4

Page 15

Alphanumeric Televison Interface Controller (ANTIC)

The primary function of the Alphanumeric Television Interface Controller (ANTIC) chip is to get data from memory, independent of the processor, for display on the video screen.

Figure 1-4 shows the pin assignments for the ANTIC.

GROUND vss Lo 40 D4 = Data Bus GTIA DATA ANS 2 39 o=DS Data Bus GTIA DATA ANIL 3 33 D6 Data Bus Light Pen cB 4 37. «-D7___ Data Bus GTIA DATA AN2 5 36 RES Reset Not Connected RNMI1 6 35 FPhg Fast Phase 0 Clock

Interrupt Output NMI 7 34 PhO Phase 0 Clock

Refresh REF. 3 33 D3 Data Bus HALT HALT 9) 32 D2 Data Bus Address Bus A3 10 ANTIC 31 DL Data Bus Address Bus A2 lL 30 Dé Data Bus Address Bus Al 12 29 Ph2 Phase 2 Clock Address Bus AG 13 23 Aa Address Bus Read/Write R/W 14 27 A5 Address Bus Ready RDY 15 26 A6 Address Bus Address Bus Alo 16 25 A7 Address Bus Address Bus Al2 17 24 A& Address Bus Address Bus Al3 18 23 AQ Address Bus Address Bus Al4 19 22 All Address Bus Address Bus Al5S 20 21 vec 5V Power

Figure 1-4. ANTIC Pin Assignments

CX5200 Field Service Manual 1-5

Page 16

Graphic Television Interface Adaptor (GTIA)

The Graphic Televison Interface Adaptor (GTIA) chip retrieves graphics data from memory via the ANTIC DMA process. This data is routed to the GTIA graphics registers. Figure 1-5 shows the pin assignments for the GTIA.

Address Bus Al 1 40 A2 Address Bus Ag 2\° 39 AB Ground vss 3 33 A4& Data Bus D3 4 37 D4 Data Bus D2 5 36 DS Data Bus DL 6 35 D6 Data Bus DA 7 suis 347 Trigger 0 Tp 8 33 R/W Trigger | Tl 9 32.0 «OST Trigger 2 T2 10 31 LUMo Trigger 3 73 Ll 30 2 Port Select st 12 29 Fgo Port Select Sl 13 28 Osc +CAV Control $2 14 27 VCC Not Used $3 15 26 HAL Not Connected . 16 25. - CSYNC Color Delay DEL 17 24 LUM 3 Alphanum. Data 0 ANO 18 23 LUM 2 - Alphanum. Data | ANI 19 22 LUM 1 Alphanum. Data 2 AN2 20 21 COL

Figure 1-5. GTIA Pin Assignments

POT Keyboard Integrated Circuit (POKEY) Address Bus Address Bus Address Bus Data Bus Data Bus Data Bus Data Bus Read/Write Chip Select | Luminance 0 Output Phase 2 Input Clock Out Oscillator Input Power HALT Output Sync Luminance 3 Output Luminance 2 Output Luminance 1 Output Color

The Pot Keyboard Integrated Circuit (POKEY) chip provides the interface between the game ports and the microprocessor. It also contains four semi-independent audio channels, each with its own frequency, noise, and volume control. the pin assignments of the POKEY.

CX5200 Field Service Manual 1-6 Figure 1-6 shows

Page 17

Ground Data Bus Data Bus Data Bus Data Bus Data Bus Phase 2 Clock Pot Scan Pot Scan Pot Scan Pot Scan Pot Scan Pot Scan Pot Scan Pot Scan Softfire 5 V Power Not Connected Keyboard Scan Keyboard Scan vss lors 40 «D2 D3 2 39S D4 3 38 =O DS 4 37, AUDIO D6 5 36 = AO D7 6 35. AL 62 7 34 A2 P6 8 3300 AB P7 9 32, OR/W P4 10 POKEY | 31 Csi P5 ll 30 CSO P2 12 29 «IRQ P3 13 28 =©=soD PO 14 27, ~OCLK Pl 15 26 = BCLK KR2 16 25 KRI vec 17 24 = SID KS 18 23 KO RG 19 22. OKI KS 20 200 (KZ

Figure 1-6. POKEY Pin Assignments

SWITCHBOX Data Bus Data Bus Data Bus Audio Out Address Bus Address Bus Address Bus Address Bus Read/Write Control Chip Select Chip Select Interrupt Request Serial Output Data Serial Output Clock Bidirectional Clock Keyboard Read Serial Input Data Not Connected Keyboard Scan Keyboard Scan

A switchbox is connected and mounted to the back of the television set. The switchbox that is used with the 4-Port Models is different from other switchboxes manufactured by Atari and from the 2-Port Model 5200. These differences include:

1) power for the Model 5200 supplied through the switchbox

  • two Select Switch functions. The two functions are:

NORMAL - Allows the Model 5200 to automatically switch between the television and the game when the Model 5200 ON/OFF switch is pressed.

STANDBY - Enables television viewing while the Model 5200 is turned on.

CX5200 Field Service Manual 1-7 Changed by ECN #0036 6/21/83

Page 18

GAME CONTROLLER

The game controller supplied with the Model 5200 is composed of an analog joystick, a 12-key Keypad, two separate Fire Buttons on each side, and three Select Buttons. The game controller is discussed in detail in Section 6.

SUMMARY

The Model 5200 is an advanced microcomputer which receives input from the Game Controllers, Read-Only-Memory (ROM) cartridges, and other peripherals. The console PC Board is housed within an outer case and contains four major chips which allow for interaction between the game and the player. They are: the Microprocessor (MPU), the Alphanumeric Television Interface Controller (ANTIC), the Graphic Television Interface Adaptor (GTIA), and the POT Keyboard Integrated Circuit (POKEY).

The console, switchbox, and Game Controllers make up the Model 5200 System which is addressed in the remainder of this manual.

CX5200 Field Service Manual 1-8

Page 19

SECTION 2

SILKSCREENS AND SCHEMATICS

On the following pages are representative silkscreens and schematics for the Model 5200. Minor variations in design may be encountered depending on the production date of the unit, but these schematics provide all details required for an in-depth understanding of all Model 5200 units.

CX5200 Field Service Manual 2-1

Page 20

Make pen and ink corrections to schematics on pages 2-4 and 2-4B as directed below.

SS Page 2-4 = Remove connector line = shown as dotted line.

F if 2 0 alslskls| AN 5] Tet slleloblsle Beveee ge ly B8sSS POKEY U7 " Page 2-4B SP sker ge Change U298 to U2

Page 2-4B Add R53 a 56

Page 2-4B Add capacitor symbol on C14.

Lowe sno LF Sor |

cousta 2 a cor sre 9 couse Ee ow Dara r Row BATA a Sow Bata RowDATA

Page 2-4B Add SF3 between +CAV and +5V on Port 4.

CX5200 Field Service Manual 2-2

Page 21

sae

CEE

2 ] pe

ATARI 5200 SUPER GAME

ils

SlsilsE laa ie

(its 1 II ~ it

EGER iF ED) 1°5 ] «| KAGREL:

Is” rie 14

Socetoe Et om. = a |

eyo" "Cities : 00 i

PORTS

5200 Motherboard Silkscreen Figure 2-1

Page 22

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 23

NOTES: UNLESS OTHERWISE SPECIFIED:

  • ALL RESISTORS ARE IN OHMS. % W. 5% CONTINUED FROM PAGE 1 ALL CAPACITORS ARE IN ul AB CDE F GHIJKL MNO PQRSTUVWXYZ ALL OTHER COMPONENTS AS MARKED.
  • REFER TO LEGEND FOR CROSS REFERENCE EXPLANATION.

R133 WA Cia S80: Lee | 1 ohol 2} *5A BASEL TA2AsAasz0 5 | 8 hvec

  • en

= i7

ik fg it +5A .

R69. 47K:

c139°84 c26 BA “BA a7 “8h ont aaa ozs jak cras* cag"SA 1 1 4 1 1 “GE a rear Sia dl Hl A] 8114] 2} 8) 14) 3h 14) 8/14} 2! 5} 14} 14) 2! 3} 14} i 14) Ho i cal 470 veo a st a Te 33 4[¥SCOODN aly reer 4f¥oCoOoN a] ¥CCDO ONT j eeoomn] 4]vocoooN 4]vecooon} 4]¥CCOODN) Sor Spr opr ‘47pF >]RAS >] RAS >] RAS 7] RAS 3] RAS 7] RAS 7] RAS {RAS AL aft AL A AY i At At AO 0 24 A0 ‘AO AQ AO EI a0 73] ag 73] ag 13] ag 13} ag 43] a6 13} ag 13] a6 13 a6 Tas ue a aU aa 20 a Ad uel THA uz + Ad ue By zs yas 2 a2 trek 1) Taf 208K x 1) a AZCIBK x ) o ml x1) $5] A2(16K x 1) Fo] A2(16K x 1) Ta] 82(16K x 1) A2(16K x 1) Er 12h a3 J) a3 12) a3 i 724 a3 a2} a3 12} 43 BI cas cas Bicas 31 cas Stas 131 CAS “Sh cas 8 CAS_ WRITE WRITE. WRITE WRITE WRITE WRITE WRITE WRITE vss Vs vss ys vss vss ys = el ie 16, 76 76 we] 16] 16) re i U28C Lsia

ATARI 5200 Super Game 5200 Motherboard Schematic (B)

Figure 2-2B

Page 24

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 25

x El 9 5 Of 0 cana (i) ‘re re) ii ND alll O xas

fe) ne Ocm ° cK EB & moO: " - ‘cm i “i i eal . 00 LE siege ASK Elsi, = Oe

Figure 2-3. 4-Port Silkscreen

Page 26

THOTT TTT TT IESE ota eo

& 201] T Vere —

so | L 3 SLR Spowt f aig ° EY is a ror ad Fit: iva ES Sid EY peel

T Rina paiT 470(x4) 001(x4) t tt peng cu2-cu6, ad PF (x4) % pire git 47014)

Figure 2-4. 4-Port Schematic 1 of4

Page 27

‘SWITCHED BG

ze J* Figure 2-4, 4-Port Schematic a % 2 of 4

Page 28

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 29

continued from page 2—11

B oD, G1 gKy" Lao pU Wi AA

+5A +5

111254) 3 +6, pASEL SSSA +5A Al7 voo"La2s8 88 kK C26. Ki BREE spl . Ay p12

8. ES —j E “1s clot = f=} ie} age * 4 =) 4 BARD ash & = BIN ABR 13) AB Aro EF eas (eKx1) = (3 SSS} i

Figure 2-4. 4 Port Schematic 4 of 4

Page 30
Note: If sockets or components are replaced, trim leads in shaded areas as close to PC Board as possible.

Figure 2-5. Trakball Silkscreen 15 pin cable game connector

Jt i [>| cons START FALSE RESET 1 1 829 o- ‘ee —_— 1 3p} COL2 2 | cous LEFT KEYPAD. RIGHT KEYPAD 3 sy S4e a ai: eee an (apele Fas On pea es nes ee ae

  • 10s1 O-+4 SZ O-4 S3 O—4 ! 10513 0-4 S14 Si! ' 7 L, | Rows EW Ne i ioe z oF ° 2 i i | | 1 He 1 1. 1 ! 54+ O-4* OSS5SO-4 OS6¢04 5160-4 OSITO-¥% OSt 6 [ey noms 1f 2 2 it? 2 9 ' i I 1 oy 1 Li! '0S7 S8 O44 $9 S19 ‘ F py Rowe 12 C4 2 9 CTH O-F 95200-49527 t 1 ol i 1 ool 3] 4 1 ' 510 sit OF 120—] S22 2 gs — ek-noms uO _f poem es pee fete | a a i i i Gaia a ee Jc a Sowreee LEFT RIGHT * ra ae pao a 1% oy |_ GND 9250 gszeo ay|_SOFT FIRE O 14 TERT RIGHT HF HE soles <ol. S279 pszep 13 oy} TRIG DB

Figure 2-6. Keypad Schematic

Page 31

2 ern rr [ Ja YAXIS QUT to} [5 XAxis OUT Os org

ASa

  • 3 R26-R23 3 1okx4.- TP2] | TPI

R22 ae vas

9] 43 CLEAR LINE IN

Figure 2-7. Trakball Schematic

Page 32

PORT 1

eee EP ye °

S38 Saas S, reed pat enced spot" 22e g

PORT 2

uit @ ki @ i yer © me

+58 R01 a 1K

‘| ———@) X35 470pF(X4) u—onm

T 470pF(X4) Vv

i — z F tt ni " Wy: ey Ss 11.8K(X2) R109. tt = We €106,C106 91-92 co7~98 ae I Ua on (xa) Ru4 J i 470 oRNT r° , T ‘eY €107,C112 : : fou Figure 2-8. 5200 2-PORT Schematic lof 5

Page 33

+58

>>m>

Ale. ts

Esreaony < saeaeer ary ° pcan pean Sc - td

GHysKL MyO pa! Continued on page 2-23 Ty wy 2a)

Figure 2-9. 5200 2-PORT Schematic 0.S.ROM A8 vas

2 of 5

Page 2-21 ae 389 o> = mi ot 2 Is: Sas

a Po O12, Ps + AE lng Aipar Re 92 Fla IND :5 vssris. 31 COMP VIDE! 5 Qssosccon 3 a ca 135 UNREG.D.C.| oH 24 — pana) Ue 2 his. Rifps Asbo + AE = ali @3 = 1 ¢ “s 1 | SHIELD}23| (oe T ‘GND.

TP. Bo +A —

bnlineerrerd waxes 88 | aseeeeomnas 8B $14, “ rd Beeqee<<e<c< Reneeees post = va Si SaB ees SoBe om SAUETE

ee re BE

Page 34

aB oD: Continued from page 2—21 PGql yXy, MNoPgkgs 0 yW yi AA

os ang A4 (eKx: eee eo: ES i TM 16[vss. 6] Vss Tm

  • Page 2-23 Figure 2-10. 5200 2-PORT Schematic 3 of 5
Page 35

62-7 a8eq

G JOH aIeWaYyrS LAOd-Z OOZES *TI-Z eanBty crs Rio osc. 4G) CONT Qi ii] IN914 1K 3906, TT RU osc C 2 3 Ri33.240 orf R18 R21 a ae Re 4050 2-R26 @ a Fi Oe ‘a CSYNC AL» 82K ! Spts ¥ Lumo (> 4 ail plone et AST ey 335 tum: — ADL 20K LUM2 ts AIELON Yok LUM3 TE AF

Rig) 2 R17 R29 v 1K 2K R31 F 68K cu R28 q 904 100P o— os 10PF 3.3K a

16K 19 RAG or wong] ¥ Qh 047 12k aupiom @- A

Page 36

WRI Es Sar rer

Page 2-27 Figure 2-12. 5200 2-PORT Schematic 5 of 5

Page 37

Q

Bae Hon

mat

() ma cS XA2: : ts

131 c22CD> ng KR & isa R101-=} C138 aD © [-73 08, h XA20] C2 R16

2 ©

a

1100 iC 99 “0 oO}

ih)

BESE

oo XA2

Ri fy J.

citio oO rr) Ref O | OLE ca Ocm oO

Dana 2 20 8c vei(—]

BINN 9 Daee Silverraan C1 Lo: is} C1301 C36 Cizgt

Page 38

SECTION 3

4-PORT MODEL 5200 TESTING

EQUIPMENT REQUIREMENTS

You require six basic pieces of equipment in order to analyze failures in the Model 5200. These items include:

15 MHz oscilloscope Diagnostic Cartridge (version 1.1) Model 5200 Port Board (Loop Back Board) CX5200 Field Service Manual color T.V. set (properly adjusted) voltmeter

TESTING WITH THE DIAGNOSTIC CARTRIDGE (VERSION 1.1)

All tests are reviewed in this section. If applicable, a Flowchart Entry Point is given. If a failure occurs, go to the flowchart indicated and continue troubleshooting.

OVERVIEW OF TESTS

The Diagnostic Cartridge (Version 1.1) contains a variety of test routines to assist you in identifying the source of problems in the Model 5200. The test cartridge is used in conjunction with the equipment listed at the beginning of this section. The tests available in the cartridge are:

Color Bar Gray Bar Any Video Pokey Adjust RAM Verify OS ROM Port Tone

INITIALIZATION

To prepare the Model 5200 for testing, perform the following steps in the order given:

e@ Connect the switchbox to the VHF terminal(s) on the back of the T.V. Set. Plug the power adaptor into the opening on the switchbox marked Power. e Plug the RF cable from the console into the opening on the switchbox marked Game. Be sure the select switch on the switchbox is set to the NORMAL position. e@ Plug the Model 5200 Port Board into the player ports. Insert the Diagnostic Cartridge (Version 1.1) e@ Turn on the T.V. Set and the Model 5200.

CX5200 Field Service Manual 3-1 Changed by ECN #0036 6/21/83

Page 39

The Model 5200 tests are run using the Port Board (Loop Back Board) which automatically cycles through all of the tests. If a test fails: turn the unit off, remove the Port Board, plug a game controller into Port |, and turn the unit back on. You can select any of the tests manually by pressing the proper key followed by the start key.

NOTE: The Diagnostic Cartridge will cycle automatically only if the Port Board is inserted before the unit is turned on.

Press the * or # key followed by the start key to print this menu on the screen.

1=Any Video 7=Ram Test 2=Color Bars 8=Verify OS ROM 3=Gray Bars 9=Display Options 4=Port Test 0=Examine 5=Pokey Adjust 6=Tone Test

Options 9 and 0 are not used at this time.

The following pages show the tests as they appear with the Port Board plugged in.

If a test fails, go to the Flowchart Entry Point indicated for that test and begin troubleshooting.

CX5200 Field Service Manual 3-2

Page 40

POWER-UP SCREEN

The Power-up screen appears in a few seconds. It displays information about the inner workings of the unit. This screen shows:

e The type of TIA in the unit. NTSC appears if the GTIA is the proper one for that unit. If PAL appears, replace with a GTIA from your kit.

e The rev of ROM in the unit. (Not important at this time.)

After the initial power-up, this screen does not automatically appear again.

One of the following indicates a failure.

e Solid Colored (Black) Screen or Vertically Lined Screen e Snowy Screen e WARPED - Ragged Picture

Solid Colored (Black) Screen or Vertically Lined Screen

If a solid colored (Black) or vertically lined screen appears, the unit is suffering a catastrophic failure. This means that the unit is not functioning well enough to even put up a simple display.

Diagnostic Flowchart Entry Point: Pg. 4-2.

Snowy Screen

If, when turned on the unit displays no modulation on the screen, the failure is probably in the power circuitry. However, first check the following:

e Check that the select switch on the switchbox is set to the NORMAL position.

e Check the power adaptor using a standard voltmeter.

Diagnostic Flowchart Entry Point: Pg. 4-9.

CX5200 Field Service Manual 3-3

Page 41

Warped - Ragged Picture

In this failure, the power-up screen appears bent to one side with a ragged edge. The picture may roll or slide down and to the left of the screen. This means that the sync. signal broadcast by the GTIA is probably not functioning. Another possible cause is that the unit is not set on the same channel as the T.V. set. Check this before going to the flowcharts.

Diagnostic Flowchart Entry Point: Pg. 4-13.

COLOR BAR TEST

e Purpose: To test the GTIA chip and associated color circuitry for correct operation.

e@ Format: A screen of horizontal color bars displays (see Figure 3-1). The screen should be steady and unchanging. A gray or blue horizontal reference line runs across the screen about three bars from its bottom. This reference line is thinner than the bars around it. R8& should be adjusted so the bars immediately above and below the reference line are within one shade of each other. Proper operation of the unit is indicated by being able to make this adjustment and by consistent color within the entire span of each bar on the screen. Minor glitches on the edges of the color bars are acceptable. Leave this test on for at least ten seconds in order to catch any intermittent problems, such as a bar momentarily changing colors or blanking out.

CX5200 Field Service Manual 3-4

Page 42
NOTE: This figure is a black and white representation of a color television screen.

\ SAME COLOR REFERENCE BAR

Figure 3-1 Color Bars Screen

Diagnostic Flowchart Entry Point: Pg. 4-14.

GRAY BAR TEST

e Purpose: To test the function of the luminescence lines (LMO , LM1, LM2) from the GTIA chip.

e Format: Eight horizontal gray bars are displayed, going from black at the top to white at the bottom in even steps (see Figure 3-2). The screen should be steady and unchanging. These lines may have minor glitches on their edges. A thin white line always appears just over the top (black) bar. No color should appear anywhere on the screen. The areas above the top (black) bar and below the bottom (white) bar are of no importance to the test. This test should be left on for at least ten seconds to ensure that there is no "flashing" of any color or shifting of the gray bars.

CX5200 Field Service Manual 3-5

Page 43

Figure 3-2. Gray Bar Screen

Diagnostic Flowchart Entry Point: Pg. 4-16.

ANY VIDEO SCREEN

e Purpose: To test the video generation of the GTIA and ANTIC chips.

e Format: The screen should have a black background with eight vertical bars. Half of the vertical bars should be narrow, and the other half much wider. A horizontal bar should appear across the top of the screen. From left to right, the shade of color on the horizontal bar should change. On the right of the bar, two Vs should be displayed, right side up.

CX5200 Field Service Manual 3-6

Page 44
NOTE: Figure 3-3 is a black and white representation of a colored screen.

Figure 3-3. Any Video Test Screen

If the Any Video test fails, swapout U3, U5.

POKEY ADJUST

e Purpose: To check the value of the pot line for the controller ports.

e Format: Adjust R132 to make the value in Port 1, HOR position read 112 +1. All other values should read between 100 and 124.

CX5200 Field Service Manual 3-7

Page 45
NOTE: Figure 3-4 shows a sample Pokey Adjust screen. The values on your screen may differ from those shown in Figure 3-4.

HOR VERT KB

1 112 107 6 2 | 110 5 (i 3 | 1lo 118 (i) 4 110 110 (i)

Figure 3-4. Pokey Adjust Screen.

Diagnostic Flowchart Entry Point: (Refer to Table 3-1, Diagnostic Error Codes).

ERROR SUMMARY

Errors during the RAM, PORT, and verify OS ROM Test are displayed on the matrix shown in Figure 3-5.

ERROR SUMMARY

01 08

O0O00 <ef—Neumber of Test

Failure Code Number of failures (Max. 99)

Figure 3-5. Error Summary.

Table 3-1 shows the defective component and/or the flowchart entry point which corresponds to the Failure Code number on the Error Summary.

CX5200 Field Service Manual 3-8

Page 46

Failure Code

NDUFLWNKO

ll

a. Table 3-1

Diagnostic Error Codes

Failure

RAM - Chip | - U25 RAM - Chip 2 - U24 RAM - Chip 3 - U23 RAM - Chip 4 - U22 RAM - Chip 5 - U21 RAM - Chip 6 - U20 RAM - Chip 7 - UL9 RAM - Chip 8 - U18

Port | - Data - Keyboard

Port 2 - Data - Keyboard Port 3 - Data - Keyboard Port 4 - Data - Keyboard

Trigger 0

Trigger 1 Trigger 2 Trigger 3

Soft Fire 0

Soft Fire 1 Soft Fire 2 Soft Fire 3

Serial Port 0 Serial Port 1

Pot Line 0

Pot Line | Pot Line 2 Pot Line 3 Pot Line 4 Pot Line 5 Pot Line 6 Pot Line 7

O.S. ROM - U8

CX5200 Field Service Manual 3-9 Reference Page #

RAM Test, Pg. 3-10

Keyboard Troubleshooting Pg. 4-21

Trigger Line Troubleshooting, Pg. 4-19

"

Softfire Troubleshooting Pg. 4-20 "

Not Used Not Used

Pot Line Troubleshooting Pgs. 4-17, 4-18

Verify OS ROM, Pg. 3-10

Page 47

RAM TEST

e Purpose: To test the 16K RAM chips for proper functioning.

e Format: This test takes approximately 10 seconds during which the screen is solid black. At the end of this time period, if the test has failed, a Failure Code number appears on the screen to signify which chip is defective. Swap out the chip corresponding to the Diagnostic Error Code (Table 3-1). If this does not solve the problem, swapout the chips U15, U16, UL7, and U28 for PCB #CA018087. For PCB #CA020108, swapout Al4, Al5, Al6é and Al7.

No Diagnostic Flowchart Entry Point

VERIFY OS ROM

e Purpose: To test the OS ROM (U8) for proper functioning.

e Format: If error code 30 appears on the Error Summary (Figure 3-5) the OS ROM chip is defective. Replace the defective chip and restart the test.

No Diagnostic Flowchart Entry Point

PORT TEST

e Purpose: This test checks the functions of the POKEY, GTIA and associated PORT circuitry.

e Format: The test is done internally with failures appearing on the Error Summary (Figure 3-5).

Diagnostic Flowchart Entry Point: (Refer to Table 3-1, Diagnostic Error Codes).

TONE TEST

e Purpose: To check the audio generation section of the POKEY (U7).

e Format: The screen prints at the bottom which register is being tested (Register 4,3,2,1). A series of eight tones will sound on each register. The first two tones may be inaudible but you can hear the speaker click.

Diagnostic Flowchart Entry Point: Pg. 4-27.

CX5200 Field Service Manual 3-10

Page 48

SECTION 3A

2-PORT MODEL 5200 TESTING

EQUIPMENT REQUIREMENTS

You require seven basic pieces of equipment in order to analyze failures in the Model 5200 2-port. These items include:

15 MHz oscilloscope Diagnostic Cartridge (version 1.1) 5200 Port Board (Loop Back Board) CX5200 Field Service Manual Color T.V. set (properly adjusted) Volt-ohmmeter Known-good 5200 controller

TESTING WITH THE DIAGNOSTIC CARTRIDGE (VERSION 1.1)

All of the tests are reviewed in this section. If a test failure occurs, enter the diagnostic flowchart where indicated and continue troubleshooting.

OVERVIEW OF TESTS

The Diagnostic Cartridge (Version 1.1) contains a variety of test routines to assist you in identifying the source of problems in the 5200. The test cartridge is used in conjunction with the equipment listed at the beginning of this section. The tests available in the cartridge are:

Color Bar Gray Bar Any Video Verify OS ROM Tone RAM Pokey Adjust

INITIALIZATION

To prepare the 5200 for testing, perform the following steps in the order given:

e Connect the switchbox to the VHF terminal(s) on the back of the T.V. set.

e Plug the power adaptor into the console. e Plug the RF cable from the console into the opening on the switchbox marked GAME. Be sure the select switch on the switchbox is set to the GAME/COMPUTER position.

CX5200 Field Service Manual 3A-1 Changed by ECN #0036 6/21/83

Page 49

e Plug a game controller into port 1 of the 5200. e Insert the Diagnostic Cartridge (Version 1.1). e Turn on the T.V. (Select Channel 2 or 3) and the 5200.

Press the * or # key followed by the start key to display this menu on the screen.

1=Any Video 7=Ram Test 2=Color Bars 8=Verify OS ROM 3=Gray Bars 9=Display Options 4=Port Test 0=Examine 5=Pokey Adjust 6=Tone Test

Test #4 and 0 are not used.

To run the tests press the proper numerical key on the 5200 controller and then press START. To escape a test (except #5), press any key. To escape #5, POKEY ADJUST, press the bottom fire button.

The following pages show the tests as they appear with the Port Board plugged in.

If a test indicates a failure, go to the Flowchart Entry Point indicated for that test and begin troubleshooting.

POWER-UP SCREEN

The power-up screen displays information about the internal status of the unit. It shows:

e The type of TIA in the unit. If the GTIA is the proper one for the unit, NTSC appears. If PAL appears, replace the GTIA with one from your kit.

e The revision level of the ROM in the unit. (Not important at this time.)

If at power-up this screen does not appear, one of the following screens appears:

e Solid Colored (Black) Screen or Vertically Lined Screen e Snowy Screen e Warped - Ragged Picture

Proceed to the description of that failure which follows.

CX5200 Field Service Manual 3A-2

Page 50

Solid Colored (Black) Screen or Vertically Lined Screen

If a solid colored (Black) or vertically lined screen appears, the unit is suffering a catastrophic failure. This means that the unit is not functioning well enough to even return a simple display.

Diagnostic Flowchart Entry Point: Pg. 4A-2.

Snowy Screen

If the screen displays no modulation, the failure is probably in the power circuitry. However, first do the following:

e Check that the Select Switch on the switchbox is set to the GAME/COMPUTER position.

e@ Check that the T.V. is set to Channel 2 or 3.

e@ Check the power adaptor using a standard voltmeter.

Diagnostic Flowchart Entry Point: Pg. 4A-10.

Warped - Ragged Picture

In this failure, the power-up screen appears bent to one side with a ragged edge. The picture may roll or slide down and to the left of the screen. This means that the sync. signal broadcast by the GTIA is probably not functioning. Another possible cause is that the unit is not set on the same channel as the T.V. set. Check this before going to the flowchart.

Flowchart Entry Point: Pg. 4A-13.

If the unit will not select a test when using a known-good controller, proceed to the Diagnostic Flowchart.

Diagnostic Flowchart Entry Point: Pg. 4A-13.

CX5200 Field Service Manual 3A-3 Changed by ECN #0036 6/21/83

Page 51

COLOR BAR TEST

e Purpose: To test the GTIA chip and associated color circuitry for correct operation.

e Procedure: Press key 2 followed by START.

e Format: A screen of horizontal color bars displays (see Figure 3A-1). The screen should be steady and unchanging. A gray or blue horizontal reference line runs across the screen two bars from the bottom of the screen. This reference line is thinner than the bars around it. R&8 should be adjusted so the bars immediately above and below the reference line are within one shade of each other. Proper operation of the unit is indicated by being able to make this adjustment and by consistent color within the entire span of each bar on the screen. Minor glitches on the edges of the color bars are acceptable. Leave this test on for at least ten seconds in order to catch any intermittent problems, such as a bar momentarily changing colors or blanking out.

Diagnostic Flowchart Entry Point: Pg. 4A-14.

NOTE: This figure is a black and white representation of a color television screen.

SAME COLOR REFERENCE BAR

Figure 3A-1. Color Bars Screen

CX5200 Field Service Manual 3A-4

Page 52

GRAY BAR TEST

Purpose: To test the functioning of the luminescence lines (LMI, LM2, LM3) from the GTIA chip.

Procedure: Press key 3 followed by START.

Format: Eight horizontal gray bars are displayed, going from black at the top to white at the bottom in even steps (see Figure 3A-2). The screen should be steady and unchanging. These lines may have minor glitches on their edges. A thin white line always appears just over the top (black) bar. No color should appear anywhere on the screen. The areas above the top (black) bar and below the bottom (white) bar are of no importance to the test. This test should be left on for at least ten seconds to ensure that there is no flashing of any color or shifting of the gray bars.

Diagnostic Flowchart Entry Point: Pg. 4A-16.

Figure 3A-2. Gray Bar Screen

CX5200 Field Service Manual 3A-5 Changed by ECN #0036 6/21/83

Page 53

ANY VIDEO SCREEN

e Purpose: To test the video generation of the GTIA and ANTIC chips.

« Procedure: Press key | followed by START.

e Format: The screen should have a black background with eight vertical bars. Half of the vertical bars should be narrow and the other half much wider. A horizontal bar should appear across the top of the screen. From left to right the shade of color on the horizontal bar should change. On the right of the bar two V's should be displayed, right side up.

If the Any Video tests fails, swapout A3 and A5, and restart the test.

NOTE: Figure 3-3 is a black and white representation of a colored screen.

Figure 3A-3. Any Video Test Screen

CX5200 Field Service Manual 3A-6

Page 54

VERIFY OS ROM

Purpose: To test the OS ROM (A8) for proper functioning.

Procedure: Press key 8 followed by START.

Format: If error code 30 appears on the Error Summary (Figure 3-1, pg. 3-8) the OS ROM chip is defective. Replace the defective chip and restart the test.

No Flowchart Entry Point.

TONE TEST

Purpose: To check the audio generation section of the POKEY (A7).

Procedure: Press key 6 followed by START.

Format: The screen prints at the bottom: Register a to 4) ? Press key 1 followed by START. A series of eight tones sounds on each register. The first two tones may be inaudible but you can hear the speaker click. Repeat for registers 2,3,4.

Diagnostic Flowchart Entry Point: Pg. 4A-17.

CX5200 Field Service Manual 3A-7 Changed by ECN #0036 6/21/83

Page 55

POKEY (PORT) TEST

e Purpose: To determine any port line failures and confirm the correct operation of the POKEY chip.

e Procedure: Press key 5 followed by START.

e Format: When you press the keys listed in the first column below, the numbers and letters in the second column should appear on the screen in the KB column:

KEY KB Readings 1 1 2 2 3 3 NOTE: When using the 1.1 Diagnostic 4 4 Cartridge to test the 2-PORT 5200, the 5 5 KB Readings may appear to the right of 6 6 any of the four ports listed on the screen, 7 7 besides the port you are testing. They 8 8 must, however, appear to the right of the 9 9 port you are testing for the test to be # D valid.

  • 0 i E START A PAUSE B RESET iS

If the keys do not register correctly when pressed, proceed to KEYBOARD TROUBLESHOOTING, page 4A-22.

Press the bottom fire button. The POKEY ADJUST screen should disappear. If it doesn't proceed to page 3A-9.

Press key 5 followed by START, again bringing the POKEY ADJUST pattern to the screen. Unplug the controller from Port | and insert it into Port 2. Repeat Step 2.

RAM TEST

Initialization for RAM Test

Purpose: To set the 5200 up for a loop test to fully check the RAM (A18- A25).

Procedure: Press key 9 followed by START. Then press key 2 followed by START. Again press key 2 followed by START. DISPLAY ERRORS CONTINUOUS TEST appears in the green band on the screen.

RAM Test Procedure

Purpose: To test the functioning of the 16K RAM chips.

Procedure: Press key 7 followed by START.

CX5200 Field Service Manual 3A-8

Page 56

e Format: Each test lasts approximately ten seconds. The screen illustrated below appears. If an error is listed on the screen, refer to Table 3-1, page 3-9, to determine which chip has failed.

ERROR SUMMARY

01 08

ee, a

Failure Code Number of failures (Max. 99)

Figure 3A-4. RAM Test Screen

POKEY ADJUST TEST

e Purpose: To test the +CAV circuit output to the controller for proper pot functioning.

e Procedure: 1. Remove the PCB assembly from its plastic housing.

  • Turn on the unit and press key 5 followed by START.
  • Plug in the loop back board (note that connectors 2 and 3 will not plug into anything).

4, Adjust R132 to make the value in Port 1, HOR position 112 +l. The values on | VERT, 4 HOR and 4 VER should read between 100 and 124, as illustrated below in Figure 3A-5. (Ports 2 and 3 have no bearing on the test for the 2-port 5200.)

HOR VERT KB

1 110 107 (] 2 | 110 5 (i) 3 | 110 118 (i) 4 | 110 110 ()

Figure 3A-5. POKEY ADJUST Test Screen

CX5200 Field Service Manual 3A-9 Changed by ECN #0036 6/21/83

Page 57

If the unit cannot be adjusted or if values are out of range, proceed to the Flowchart Entry Point: Pg. 4A-20.

POKEY SOFTFIRE TEST

Connect the oscilloscope to pin 16 of A7 (1 v/division;10ms/div.).

Insert the controller into port 1.

Press key 5 followed by START.

Press the top fire button (softfire).

A 5v p-p square wave signal should appear. If it does not, proceed to the SOFTFIRE TROUBLESHOOTING FLOWCHART, page 4A-19.

Unplug the controller from port | and plug it into port 2.

Repeat the fourth and fifth steps for port 2.

CX5200 Field Service Manual 3A-10

Page 58

SECTION 4

4-PORT 5200 DIAGNOSTIC FLOWCHART

The Diagnostic Flowchart is intended to be easy to use and the primary aid when troubleshooting the 4-Port 5200. Follow the prompts in the order presented. When a question is asked, follow the line from the box that best applies to your unit's condition. When that line terminates with a letter inside a circle, locate the letter on a different page and continue the diagnosis. The flowchart leaves nothing to chance; it tells you when to perform a specific test and when to replace components.

SWAPOUT PROCEDURE

At many places in the diagnostic flowchart, a box tells you to "swapout" a component, a chip, or a number of chips in a particular order. The "swapout" instruction means that you should replace the indicated components (one at a time) with known-good components of the same type. The unit should then be tested with the new, known-good component(s) in place to see whether the swapout solved the problem being checked. If the swapout did not fix the problem, leave the new chip in and swapout the next. Repeat this procedure for the rest of the components. Once the unit functions properly, reinstall the original IC's one by one to determine which are actually defective.

REPLACE IN ORDER

The "replace in order" instruction means that you should replace the components indicated in the order listed until the result called out in the previous block is obtained.

F - Some lines terminate with an F inside a circle. When this occurs, return to the beginning of the test sequence on page 3-1.

N - Some lines terminate with an N inside a circle. When this occurs, call your Atari Repair Hotline.

Inside California (800) 672-1466

Outside California (800) 538-1535 (800) 538-1536

CX5200 Field Service Manual 4-1 Changed by ECN #0036 6/21/83

Page 59

Black Screen Troubleshooting

Is there +5V on the output of VR1?

Is there a 1.78975 MHz signal on Pin 30 of U5? Is there a 1.78975 MHz signal on Pin 29 of U3?

Is there a 3.5795 MHz signal on Pin 28 of U5?

Swapout

  • U5
  • U3

Open between U5 Is there a 3.57950 MHz Pin 29 & U3 Pin 35. signal on Pin 35 of U3? ae ——————— Yes

y Is there a 1.78975 MHz signal on Pin 34 of U3?

Yes Open between U2 Pin 37 and U3 Pin 34.

Yes

Repair or Replace C) Page 4-5

—< Is there a 1.78975 MHz signal on Pin 37 of U2?

***NOTE*#*

F Jf you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

©X5200 Field Service Manual 4-2

Page 60

Black Screen Troubleshooting (Cont.)

Are the following voltages on the pins of the transistor:

Ql 92 Base 3.5V 3.5V No Emitter 4.3V 4.3V Collector 1.2V 1V Are voltages correct? Replace transistor(s).

No Yes

Replace YI.

Check for open, shorted or wrong value component in clock circuit. Does unit

function?

Yes

Repair or Replace

LS = *¥**NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX 5200 Field Service Manual 4-3

Page 61

Black Screen Troubleshooting (Cont.)

VRI?

0 V on point@of the schematic?

Defective

  • R57 Is there approximately 11-13V on the input of

Is there approximately

1)Q6 3) R56 Defective VR1 or output short to ground (possible chip)

Defective J1 or open between point@of VR2 & point@of VR (with cartridge in).

CX 5200 Field Service Manual ***#NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

Page 62

Black Screen Troubleshooting (Cont.)

Swapout

  • U2
  • U3
  • US Is there a 1.78975 Mhz signal on Pin 39 of U2?

Open between Pin 39 U2 and Pin 29 of U3 and Pin 30 of U5.

*#**£NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-5

Page 63

Black Screen Troubleshooting (Cont.)

a) PCB HH

epair open between x = ie = eynero ks uprolan chip « 5 or ground. ev ; 7 chips? (See chart. ma ta fe pout y (Check for bad socket) Us 20 10 as US 27 3 AG U6 16 3 Az u7 7 1 Ag us 2u 12 ag us 16 3 Me Gu ts $ Defective Ul or other Me te : Is Pin 40 of U2 at 5V? Reset circuitry als Ula 1s 7 connected to U2 Pin 40. UlS 20 10 Aig Ul6é 16 & Al7 UIT 16 &

Alg U19 8 16 Azo U20 8 i aay U2l 8 H ‘ Open Pin 36 of U2 to

  • U2 8 16 2 Pp ] a ha Is Pin 36 of U3 at 5V? Pin 40 of U5. 2% u2u 16 A25 U25 8 16 U26 Not used A27 U27 14 u2zs 14 7 _ U2 ie 7 Bad te y Swapout Repair
  • U2 on
  • U3
  • US Replace
  • U8 :
  • U7

Is problem repaired?

***NOTE***

Page 4-7. If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-6

Page 64

Black Screen Troubleshooting (Cont.)

Yes == Is there a data signal on Pin 2 of UL8 - U25?

Yes

been

Is there a data No signal on Pin 14 Open Trace RAM chip Pin 2 to U2 Or replace defective RAM.

of UL8-U25?

Yes

Swapout

  • UL4
  • UIS
  • Ul6
  • UL7

Is there a good display?

Defective:

  • U28 (CA018087 only) Page 4-8
  • L4-L6 ~~
  • C30-33
  • Open Address

Repair or Replace

is there a good display?

Swapout U18-U25 Ye Tf only one chip is missing signal, replace that chip. If not, proceed.

Does unit function?

Is there 4V p-p signal on Pin 6 of U28?

Defective:

  • U28
  • L4-L6
  • C30-33 Is there a 4V p-p signal on Pin 4 of UL8 - U25?

Repair

or Repl Swapout gbaace

  • Ul4
  • U28 or Open Pin 4 of RAM chip(s) to Pin 8 of UL4

©X5200 Field Service Manual ***NOTE*##*

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

Page 65

Black Screen Troubleshooting (Cont.)

Is there a 4V p-p signal on Pin 15 of U18-U25? Swapout Yes

Swapout

  • UL7
  • U14 or defective R133,C140,R68 & C55

*** NOTE ***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX 5200 Field Service Manual 4-8

Page 66

Snowy Screen Troubleshooting

Defective

  • RF Cable
  • Switchbox
  • Battery Eliminator Is there 10 to 12 volts on the core of J3?

Is C48 good? (Do not short across)

Defective

  • L13
  • RF Module or open between Pin 2 RF module & VCC2. Is there +5 on Pin 3 of the RF Module?

Is there +12 volts on input of VR2?

Does Pin 13 of U29(A26)* change between 13V No & OV when S2 is pressed? Page 4-11

Press S2 so that Pin 13 is high. *U29 is chip designation, on PCB #CA018087 A26 is chip designation on PCB #CA020108

***#NOTE*#* Page 4-10 If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A. CX5200 Field Service Manual 4-9

Page 67

Snowy Screen Troubleshooting (cont.)

ga eg Is there 0V on the . collector of Q8? Defective Q8 or Q9.

Yes gj rc Is there 13V on the Defective base and 14V on the 1) @ emitter of Q7? 2) R55

  • R58 or Yes open trace to collector of Q8. | Defective Q7

<=

*#*#*NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX 5200 Field Service Manual 4-10

Page 68

Snowy Screen Troubleshooting (cont.)

<=>

No ; Yes Does Pin 11 of U2xA26i*P ES] Is Pin 10 of U29KA26iat Replace Q10 Does unit work? FS toggle each time S2 ov? is pressed? No Yes No Open trace or feces conduct ‘ defective resistor € continuity lo or capacitor in A between Pin 9 & 12 Repair trace. Grevitry. Does Pin 6 of U29A26)'bo of U29(A26)7* . high when S2 is pressed and low when it is released? Yes Yes = Replace U2%(A26) Repair or Replace No

Check for possible shor ts or opens on the failing pin or defective 2.

Repair

L > <<

***NOTE*** *U29 is chip designation on PCB #CA018087 A26 is chip designation on PCB #CA020108

CX5200 Field Service Manual If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

Page 69

Snowy Screen Troubleshooting (cont.)

| Repair Is there +5v on the Yes Open Pin 3 VR2 to ae output of VR2? VCC2, +5B or +5F. Replace

No Tpa3vRo dotted If Pin 3 VR2 short to ground: ossible short in chips. Remove chips one-by-one and turn on unit. If modulation occurs, bad chip has been located. If chips are not shorted, check for possible CAP or trace shorted on board.

CX 5200 Field Service Manual ***NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

4-12

Page 70

Warped Ragged Picture Troubleshooting

Manually set 5200 on power - up screen.

Is there a +5 p-p signal ‘on the leg of R22 Yes No connected to Pin 4 's R22 good? of U1?

No Yes

se Mistuned or defective RF! Replace Open between Pin 4 of [YES Is there a +5V p-p module or L12 or open be. =< ° Al & R22 signal on Pin 4 at U1? tween R22 & RF module oF Pin 4. Repair

No |

Defective Ul orno [SE] Is there a +5V p-p et power or ground to Ul. Pt} signal on Pin 5 of UL?

No

° b us Yes Is there a +5V p-p i pen between Ss signal on Pin 25

Repair Pin 25 and UI Pin 5. Bnet US?

No

Swapout:

  • US
  • U2
  • U3

~—t-

*#**NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

4-13 CX5200 Field Service Manual

Page 71

Color Troubleshooting

Manually set unit onto color bars pattern.

Is frequency of Y1 3.5795. No Replace Y1

Yes —— — a Does Pin 17 of U5 i adjust between 0 and No pee A 1) R8 6 volts when R8 is dj ‘d 2) CR2 adjusted. 3) CR3

Yes

With Pin 17 of U5 ad- No | Defective ]

  • U5 or justed to 6V is there a 4 volt p-p signal on pin 21 of U5?

Is there a 2 volt p-p

  • Cll

Defective C11 or signal between Cl1 & R28?

Yes

Page 4-15 open Cl! to U5 Pin 21.

***NOTEX**

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX 5200 Field Service Manual 4-14 Repair

or

Replace

Page 72

Color Troubleshooting (cont.)

Is there a .4v p-p signal on the base of Q3? Defective R28 or open Trace R28 to Q3. at

Is there a 4v p-p No ; signal on the collector a Pel beta Defective R29. of Q3?

Yes Yes

Is there a 3 volt p-p signal between C9 and R31? Defective R30

Mistuned R.F. Module or defective:

  • R31
  • RF Module or open R31 to R.F. Module Pin 4. Defective C9 or open C9 to the collector of Q3.

Repair

or

Replace

***NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX 5200 Field Service Manual 4-15

Page 73

Gray Bars Troubleshooting

Manually set the 5200 to the Gray Bars pattern.

Is there a +5V p-p signal on the side of ] Yes R23, R24, & R25. Connected to Ul? Defective R23,R24, R25 or open between R23,R24, or R25 and [7] R.F. Module Pin 4.

No

Reference the line on the chart below which has the resistor that did not have the proper signal.

Is there a +5V p-p

CX 5200 Field Service Manual 4-16 , Yes} Open between U1 outsignal on the UL put and that resistor. [7] output pin? **#*®NOTE***

aA A Aan No If you are servicing a unit containing PCB CA020108, chip designators have Is there a +5V p-p —) ean “| jefective Ul or no been changed from U to A. signal on the Ul Yes +-3V or ground a input pin? to UL.

No

N No 7 No Is there a +5V p-t Yes i ji Js pullup resistor P-P Open between U2 pin & Repair wood? —“] signal on the U2 pin? eee Ulinput a!

Yes

Room Repair i or ja —!

  • U2 Replace
  • U3

F

Line # Resistor # U1 Output UL Input Pullup # US Pin #

LM@ 2 3 R18 31 LMI 6 7 R19 22 LM2 12 lL R20 23

Page 74

Pot Control Line Troubleshooting

Manually set the 5200 to the Pokey Adjust test.

Can +CAV on defective port be adjusted between 4-6.4V by turning R132? No

Page 4-18 Yes

Swapout U7 ***NOTE***

If you are servicing a unit containing | PCB CA020108, chip designators have Do pot lines pass? Yes been changed from U to A.

_—__, No

From Error Code on chart below determine which line is defective & check the components for correct value. -

—= = . No Open or shorted Do POT Lines pass? trace. Repair

Yes ~t

POT Line Pokey Adjust Port and Pokey U7 Error Code Failure Pin # Pin # CAP #1 CAP #2 Resistor

22 HOR | 1-10 14 C98 C106 R106 23 VERT 1 1-11 15 c97 C105 R110 24 HOR 2 2-10 12 C96 C104 R107 25 VERT 2 2-11 13 c95 C103 RIL 26 HOR 3 3-10 10 co4 C102 R103 27 VERT 3 3-11 1 93 C101 R112 28 HOR 4 4-10 8 92 C100 R109 29 VERT 4 4-11 9 cal c99 R113

CX 5200 Field Service Manual 4-17

Page 75

Pot Control Line Troubleshooting(Cont.)

*¥**NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have Yes been changed from U to A. x

coo Swapout

  • US
  • U7

a | Can +CAV be adjusted now?

em No

[heck the voltages on QIL1-Q14 and compare readings to the ones shown for the "A" condition in the chart below.

CX 5200 Field Service Manual Are the readings Replace transistor. Does Bokeyiedlust Yes correct? pass? lL — Yes No

= = —

Put unit into Port Test Defective component mode but do not put in in Pokey Adjust Port board (loop back circuitry. board).

= oe

besa sees . Check the voltages on Repair Q11-Q14 and compare readings to the ones shown for the "B" No condition on the chart below. Are the readings Yes Check for opens & Gare shorts in circuitry & = repair.

Condition/ Qi Qi2 Qi3 Qa F Transistor A B A B A B A B

Emitter 13V 13V 3.2V ov ie} 0 3.2V ov Base 12v 13V 4v ov 0 .7V 3.8V ov Collector 4-6.4V ov 13V 13V 3.8V ov 12v 13V

4-18

Page 76

Trigger Line Troubleshooting Bottom Fire Button

i

Defective:

  • U5
  • U5 Socket
  • Cap on that line. \ See chart. No po Is the U5 pin for the defective Port at +5 volts with everything unplugged from the Port?!

Yes

Plug in controller.

CX 5200 Field Service Manual 4-19 hae

No ‘ Is pin still at +5V? Defective controller.

Yes ST

Push and hold bottom fire button.

= A

  • - = Does signal drop to | no Is trigger line Go to controller approximately shorted to +5V? section. 0-.7 volts? Page 6-1 hescesccac: Yes Yes

Defective U5

i ~<-

Port US Pin # Cap #

1 8 110 2 9 109 3 10 103 4 ll 107 F

***NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

Page 77

Softfire (Top Fire Button) Troubleshooting

Insert Diagnostic cartridge into console. Insert Game Controller into Port lL. Manually select Pokey adjust test. L_sciustcese Are there 5V p-p wave-

forms at U13 Pins 9

Yes Replace UL3 el Na % 10? Are there 5V p-p waveforms at UL3 = Pins 1,2,4 & 5? —_ : Yes are tere 5Vp-p No Replace US = waveforms at US Pi 2 Depress & hold soft Ins 14 & 137, Jj fire button. Is U13_ No Pin 3 pulsing? Yes

Yes

Swapout and retest, in ‘ . i With softfire button

the following order: Jv, ] held down, are there

  • U7 5V waveforms at U7
  • U3 Pin 16? :
  • US Repair broken traces LL : =8 from U5 to U13. Ne y =>
  • = Repair open trace from UL3 Pin 3 to U7 sD | Check waveformat | Yes U13 Pin @ (see chart Replace U13. below). Is it now low? Y : No
Note:@) Port | check Pin 4, U13 Check for opens from Repair Port 2 check Pin 2, U13 pin @ (see chart) Port 3 check Pin 5, U13 to port plug Port 4 check Pin 1, U13 and game controller

bl > <=—

*#**NOTE* **

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX 5200 Field Service Manual 4-20

Page 78

Keyboard Troubleshooting

a)

Is the failure on Port 1?

Manually select Pokey Adjust Test.

Are there 5v p-p square waves on Pin 6 of U9 - U12? No

Page 4-26

Are there 5v p-p square] No | Replace waves onPin 9 .& 10 of U7 U9-U12?

Yes

Which port failed?

Port 3 Page 4-25

*#**#NOTE**#*

Page 4-24 If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-21

Page 79

Keyboard Troubleshooting (cont.)

Is there Ov on Pin 6 Is there +5 on Pins 1,2, Replace U27 of U9 & ULL? 4 & 5 of U27?

5 On Defective U5 or open

traces from U5 to U27.

Is the problem repaired?

Check capacitors & resistors on Pins 1-8 of Port 1 for proper value & operation. Replace if defective.

*#*#*#NOTE*#*

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-22

Page 80

Keyboard Troubleshooting (cont.)

Swapout

  • U9
  • UL2

Yes Does Port 2 pass?

Check capacitors and resistors on Pins | -8 of Port 2 for proper value & operation. Replace if defective.

**®*NOTE?#*

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-23

Page 81

Keyboard Troubleshooting (cont.)

Yes Does Port 3 pass? ,

Check capacitors & resistors on Pins 1-8 of Port 3. Replace if defective.

*#**NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-24

Page 82

Keyboard Troubleshooting (cont.)

Does Port 4 pass? Yes

Check capacitors & resistors on Pins 1-8 of Port 4. Replace if defective.

***NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-25

Page 83

Keyboard Troubleshooting (cont.)

Swapout

  • U27
  • U9
  • ULL Are signals missing on U9 and/or ULI only?

Replace

U5

*#**NOTE***

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-26

Page 84

Audio Troubleshooting

Cz

Is there a 4.5 Mh: ; Yeef Can Li be adjusted to {No} signalon the emitter Adjust give a 4.5 Mhz reading? ‘of QU?

No Yes

7 No Replace: | 4, Is there +5VDC * With audio test going

  • LI = on the collector of is there a series of | No Swapout Does audio 2)L2 Qu? changing square waves )u7 work? ” on U7 Pin 377 2) U2 es Yes

Replace: Yes

  • C13
  • C14 Defective C15 Is the approximate same 2Q8 series of signals Be, eakopen) visible between C15 & U7 Pin 37 & a R41? cls.

( ) Yes Open Is there a 4.5 Mhz 1-2v JNO P-p Signal on the side C10 to Q4. of C10 connected to Q4?

Yes

Defective: Repair

  • C10
  • R33 > or Replace

—«<!

*If second time at this step, call ATARI Repair Hotline. F

***NOTE*##*

If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 4-27

Page 85

SECTION 4A

2-PORT 5200 DIAGNOSTIC FLOWCHART

The Diagnostic Flowchart is intended to be easy to use and the primary aid when troubleshooting the 2-Port 5200. Follow the prompts in the order presented. When a question is asked, follow the line from the box that best applies to your unit's condition. When that line terminates with a letter inside a circle, locate the letter on a different page and continue the diagnosis. The flowchart leaves nothing to chance; it tells you when to perform a specific test and when to replace components.

SWAPOUT PROCEDURE

At many places in the diagnostic flowchart, a box tells you to "swapout" a component, a chip, or a number of chips in a particular order. The "swapout" instruction means that you should replace the indicated components (one at a time) with known-good components of the same type. The unit should then be tested with the new, known-good component(s) in place to see whether the swapout solved the problem being checked. If the swapout did not fix the problem, leave the new chip in and swapout the next. Repeat this procedure for the rest of the components. Once the unit functions properly, reinstall the original IC's one by one to determine which are actually defective.

REPLACE IN ORDER

The "replace in order" instruction means that you should replace the components indicated in the order listed until the result called out in the previous block is obtained.

F - Some lines terminate with an F inside a circle. When this occurs, return to the beginning of the test sequence on page 3A-1.

N - Some lines terminate with an N inside a circle. When this occurs, call your Atari Repair Hotline.

Inside California (800) 672-1466

Outside California (800) 538-1535 (800) 538-1536

CX5200 Field Service Manual 4A-1L Changed by ECN #0036 6/21/83

Page 86

BLACK SCREEN TROUBLESHOOTING

o>

Is there +5V to all No Repair open between chips? (See chart)

a Yes chip & +5 or ground, (Check for bad socket)

Pin 40 of A2 at 5V? No | Defective Al or “other reset circuitry connected to A2 pin 40. IC# +5 Gnd Al T 3 A2 8 1,21 A3 21 AS 27,3 Is

AG 16 8 A7 7 1 Ag 2412 Ag 16 8 Alo 16 8 All 16 8 Ala 147 Als 147 Alé 16 8 Al7 168 Alg 8 16 Alo 8 16 A208 16 A2L 8 16 A228 16 A238 16 A288 16 A2 8 16 A27, lh

CX5200 Field Service Manual Is Pin 36 of A3 at 5V? Open Pin 36 of A3 to Pin 40 of A2.

Yes

Swapout

  • A2
  • A3
  • AS
  • A&
  • A7

Is problem repaired? Yes

4A-2

Page 87

CX5200 Field Service Manual BLACK SCREEN TROUBLESHOOTING (Continued)

Is there approximately Defective VR1 or output short to 9V on the input of VR1? ground (possible chip)

No

Is there approximately QV on point@of the No Defective J2 or open between pointof schematic?

Yes

Defective

  • @&
  • R57 VR2 & point@of VRI (with cartridge in).

Repair

4A-3 Changed by ECN #0036 6/21/83

Page 88

BLACK SCREEN TROUBLESHOOTING (Continued)

No Repair open between Is there +5V to all chip & +5 or ground. chips? (See chart) (Check for bad socket)

IC# +5 Gnd Y AD oT 8 “s

A2 g as Defective Al or other

A BF a Is Pin 40 of A2 at 5V? reset circuitry connecta3 73 . ed to A2 pin 40.

A7 7 1 Ag 24 «12 Yes Ag 16 8 Alo 146 8 : ? All 16 8 Is Pin 36 of A3 at 5V?

Al4 4 7 AlS 4 7 Alé 16 8 Yes

Al7 16 8 Al8 8 16 Alg 8 16 A20 16 A2l 16 A22 8 A23 8 16 A24 A25 A27 Yes Is problem repaired?

Note: Some 5200 2-port boards have pins 1,8,9,10 and 11 of A7 jumpered together on the solder side of the PCB. Future PCB's will incorporate this jumper. Do not add these jumpers to the 5200 2-port board.

CX5200 Field Service Manual 4A-4

Page 89

BLACK SCREEN TROUBLESHOOTING (Continued)

Are the following voltages on the pins of the transistor:

QL g2

Base 3.5V 3.5V No Replace Are voltages

Emitter 4.3V 4.3V . Collector 1.2V IV transistor(s). correc = mad a No Yes

Replace Y1.|

Does unit Check for open, . shorted or wrong function? value component in ‘ves clock circuit.

Repair or Replace

aa

CX5200 Field Service Manual 4A-5 Changed by ECN #0036 6/21/83

Page 90

BLACK SCREEN TROUBLESHOOTING (Continued)

Swapout

  • A2
  • A3
  • AS Is there a 1.78975 MHz signal on Pin 39 of A2?

Open between Pin 39 A2 and Pin 29 of A3 and Pin 30 of Ad.

CX5200 Field Service Manual 4A-6

Page 91

Whenever the flowchart directs you to F, return to the beginning of the testing procedure in Section 3. Proceed until another error is encountered and you are again directed to enter the flowchart or until the unit has proven to be fully operational.

CX5200 Field Service Manual 4A-7 Changed by ECN #0036 6/21/83

Page 92

BLACK SCREEN TROUBLESHOOTING (Continued)

Cc)

Open Trace RAM Is there a data signal No chip Pin 2 to A2 Repair on Pin 2 of Al8-A25? or replace defective RAM

Yes

Isthere a data signal No sentyjone[chiplis) on Pin 14 of AL8-A25? missing signal, replace that chip, if not proceed

Yes

Swapout i ie De rns Does unit function?

  • ALS
  • Alé No
  • ALT Is there 4V p-p signal No on Pin 9 of Al7? |

\Y es| Is there a good Yes Replace display? Al7 Yes Is there a 4V p-p No signal on Pin 4 of A18-A25? Defective:

  • ALS
  • L4-L6 No
  • C30-33
  • Open Address Swapout line to RAM aa
  • Al5 or open Pin 4 of RAM chips) to Repair or Replace Pin 8 of Al&

Is there a good Yes display? =

No.

Swapout A18-A25

~.

CX5200 Field Service Manual 4A-8

Page 93

BLACK SCREEN TROUBLESHOOTING (Continued)

co

Swapout Al 5 or No Is there a 4V p-p

replace defective «| signal on Pin 15 of C30-33, L4-6. Al18-A25?

Yes

Swapout

  • Al7
  • Al4 or defective R133,C140, R68 & C55

E

CX5200 Field Service Manual 4A-9 Changed by ECN #0036 6/21/83

Page 94

SNOWY SCREEN (POWER SUPPLY) TROUBLESHOOTING

Co

Is LED on?

No

Is there 5VDC on the output of VR2 or pin 3 of the R.F. modulator? Yes Defective LED or

No

Is there at least +7VDC on the input of VR2? Yes open from LED to VR2. el

Defective VR2 or |

No

Is the base of Q7 0.7-1.0VDC less than the emitter?

No

No

J1

CX5200 Field Service Manual Yes Defective Q7.

4A-10 shorted output VR2. |

Is the collector of Yes Defective R58 or a Q8 at 0 volts? broken trace to Q7.

Replace or Repair

Page 95

SNOWY SCREEN (POWER SUPPLY) TROUBLESHOOTING (Continued)

Cc

Is there +5VDC on pin 3 of the R.F. module? No

Yes

Is there gnd on pin | of R.F. module? Defective L13 or open pin 3 R.F. to VR2.

Yes

Defective

  • R.F.module
  • R.F. Cable
  • 33 Open R.F. pin 1 to ground.

Repair or Replace.

CX5200 Field Service Manual 4A-11 Changed by ECN #0036 6/21/83

Page 96

SNOWY SCREEN (POWER SUPPLY) TROUBLESHOOTING (Continued)

Yes A the Base SS Q8 Defective Q3. -

No

Is base of Q9 wes at 9-15.0 VDC? Defective Q9.

No

Does Pin 11 of A26 Yes change states when Defective A26 switch S2 is depressed?

No

Check condition of $2,C47,Q10,R61. Also verify 9.0-15.0VDC at pin 14 of A26.

Repair as required.

—<¢

CX5200 Field Service Manual 4A-12

Page 97

WARPED, RAGGED PICTURE TROUBLESHOOTING

Manually set 5200 on power - up screen.

Is there a +5 p-p signal on the leg of R22 connect} Yes No ed to Pin 4 of Al? IsR22 good?

No Yes

istuned or defective R.F. Open between Pin 4 of [YS] Is there a +5V p-p odule or L12 or open be- Replace —~?—J Al and R22. PE} signalon Pin 4 at Al? module or Repair

No

Defective Al Yes | Is there a +5V p-p a efective Al or no < +5 p+ power or ground to Al. signal onPin 5 of Al?

No

Yes| Is there a +5Vp-p Repair Pug] pen between AD | | ed signal on Pin 25 of AS?

No

Swapout:

  • AS
  • A2
  • A3

CX5200 Field Service Manual 4A-13 Changed by ECN #0036 6/21/83

Page 98

COLOR TROUBLESHOOTING

Manually set unit onto color bars pattern.

Is frequency of Yl 3.5795. Replace Y1

Yes

Does Pin 17 of A5 A Defective adjust between 0 and 1) R8 6 volts when R8 is 2) CR2 adjusted? 3) CR3

ee

Yes a oe ; No Defective With Pin 17 of A5 ad- 1) AS justed to 6V is there a 2) Cll 4 volt p-p signal on pin 21 of U5?

Defective Cll or open Cll to A5 Pin 21. Is there a 2 volt p-p signal between Cll & R28?

CX5200 Field Service Manual 4A-14

Page 99

COLOR TROUBLESHOOTING (Continued)

i} Defective R28 or open Trace R28 to Q3. |

Is the signal present at approximately 0V? Is there a .4v p-p signal on the base of Q3?

Is there a 4v p-p signal on the collector of Q3? Defective R29.

Yes

Is there a 3 volt p-p signal between C9 or R31? Defective R30

Defective C9 or open C9 to the collector of Q3. Mistuned R.F. Module or defective:

  • R31
  • RF Module or open R31 to R.F. Module Pin 4.

a

Repair

or

Replace

CX5200 Field Service Manual 4A-15 Changed by ECN #0036 6/21/83

Page 100

GRAY BARS TROUBLESHOOTING

co

Manually set the 5200 to the Gray Bars pattern.

Defective R26,R24 Yes | R25 or open between R26,R24, or R25 and R.F. Module Pin 4. Is there a +5V p-p signal on the side of R26,R24, & R25 connected to Al?

No

Reference the line on the chart below which has the resistor that did not have the proper signal.

Is there a +5V p-p Yes} Open between Al signal on the Al output and that output pin? resistor.

No

Is there a +5V p-p Yes Defective Al or no signal on the Al +5V or ground to input pin? Al.

No

No . N 1 : . Is pullup resistor 1c 's there a +5V p-p Yes] Open between A5 pin Repair! at ood? P&H] signal on the A5 pin? and Al input.

Yes

Swapout Repair

  • AS at. a ae Replace
  • A3 P ‘

! F

Line # Resistor # Al Output Al Input Pullup # = AS Pin#

LMI* R24 6 7 RIS 22 LM2 R25 12 u R20 23 LM3 R26 10 9 R21 24

*The 1.1 Diagnostic Cartridge does not test LMO.

CX5200 Field Service Manual 4A-16

Page 101

AUDIO TROUBLESHOOTING

Yes EJ Adjust Can LI be adjusted to give a 4.5 Mhz reading?

No

Replace] No be} LI Pe Is there +5VDC on the collector of Q4?

Yes

Replace:

  • C13 acy 3%
  • CRE
  • CR7

*If this is your second time at this step, call the ATARI Repair Hotline (see page 4A-1).

€X5200 Field Service Manual cs

Is there a 4.5 Mhz signal on the emitter of QU?

Yes —~x-

No *With audio test going is there a No Swapout Dees audio) series of changing 1) A7 pa square waves on A7 2) A2 ? Pin 37? Yes Yes

Is the approximate same series of signals |No__ | Defective C15 visable between C15 & or open A7 Pin Fas Rel? 37 and C15.

Yes

Is there a 4.5 Mhz 1-2v | No Open p-p signal on the side | of C10 connected to Q4? C10 to Qt.

Yes

Defective: Repair

  • Clo or
  • R33 Replace.

F

4A-17 Changed by ECN #0036 6/21/83

Page 102

TRIGGER LINE (BOTTOM FIRE BUTTON) TROUBLESHOOTING

(See Chart Below) cS

Defective: DAS

  • Socket of AS
  • Cap on that line Is the AS pin for the defective port at +5 volts with everything unplugged from the port? (see chart below)

Yes

Plug in controller.

No. : Is pin still at +5V? Defective controller.

Yes =

Push and hold bottom fire button.

Does signal drop to N Is trigger line Go to controller approximately = jor ted to) V2 7 section. O-I volt? for open. No Page 6-1

Yes Yes

Defective A5.

~t

Repair or Port AS Pin # Cap # Res# Replace 1 8 Ci2 RUG 2 9 C107 RLI7

F

Note: Some 5200 2-port boards have pins 1,8,9,10 and 11

CX5200 Field Service Manual 4A-18 of A7 jumpered together on the solder side of the PCB. Future PCB's will incorporate this jumper. Do not add these jumpers to the 5200 2-port board.

Page 103

SOFTFIRE (TOP FIRE BUTTON) TROUBLESHOOTING

ce

Be sure Pokey Adjust Screen is displayed. If not, press key 5 and then START.

When the top fire button] yes Me is pressed does pin ) A7 16 of A7 show 5V p-p? By fe

No

Does output pin of multiplexer pulse to | Yes 5 tput pin 5V p-p when top fire pen output P. button is pressed? fojpinieetzen (See Chart below)

No

Does input pin go Yes Defective Low when top fire 1) Multiplexer button is pressed? 2) A7

No

Defective

  • Cap
  • Port
  • Open Port to Multiplexer

=z

Repair or Replace.

Multiplexer Port Output & Pin Input Pins 1 A9 Pin 3 1,2,4,5 2 Al0 Pin 13 11,12,14,15

Note: Some 5200 2-port boards have pins 1,8,9,10 and 11

CX5200 Field Service Manual of A7 jumpered together on the solder side of the PCB. Future PCB's will incorporate this jumper. Do not add these jumpers to the 5200 2-port board.

4A-19 Changed by ECN #0036 6/21/83

Page 104

POTENTIOMETER CONTROL LINE TROUBLESHOOTING

<>

‘Manually set the 5200 to the Pokey (Port) Test, page 34-8.

Can + CAV on pin 9 of defective port be adjusted between 4-6.4V by turning R132? No

Yes

Swapout A7

Do pot lines pass?

No

From chart below determine which line is defective & check the components for correct value.

Open or shorted De POT Lines pass? Fo trace. Repair

Yes J

POT Line Pokey Adjust Port and Pokey (A7) Error Code Position Pin # Pin # CAP #1 CAP #2 Resistor

22 HOR 1 1-10 14 C98 C106 R106 23 VERT | L-lL 15 C97 C105 R110 24 HOR 4 2-10 12 C92 C100 R109 25 VERT 4 2-11 13 co c99 RUZ

Note: Some 5200 2-port boards have pins 1,8,9,10 and 11 of A7 jumpered together on the solder side of the PCB. Future PCB's will incorporate this jumper. Do not add these jumpers to the 5200 2-port board.

CX5200 Field Service Manual 4A-20

Page 105

POTENTIOMETER CONTROL LINE TROUBLESHOOTING (Continued)

Cc *Refer to the chart at the bottom of the page for +CAV transistor state levels.

  • Discrete Component

L ee ad Swapout AS

Yes

Is the collector No Defective Q13 of Q13 High? or discrete component.

Yes ee Is the emitter of No . ' Defective Q14 High? ata

  • Q12 Yes 3) Discrete component

Defective

  • QL
  • R132

Repair or Replace.

F

Condition/ Quit Qi2z Q3 Qi4 Transistor A A B A B A B

Emitter 13V 13V 3.2V ov fo) fe} 3.2V ov Base 12v 13V 4v ov 0 .7V 3.8V ov Collector 4-6.4V 13V 13V 3.8V ov 12V 13V

A: Pokey Adjust Selected B: Other 1.1 tests (excluding Port Test)

CX5200 Field Service Manual 4A-21 Changed by ECN #0036 6/21/83

Page 106

KEYBOARD TROUBLESHOOTING

a

Is the failure on Port 1?

No

Manually select Pokey Adjust Test, pg. 3A-2.

Are there 5v p-p No Is there a 5v p-p No square waves on Pin square wave on pin Replace A5. 6 of AI & Al0? 12 of A5?

Yes Yes

Are there a 5V p-p Replace A27. square waves on Pins 9 and 10 of All, A9, Al0?

No

Check for 5v p-p No signals at pins Replace A7. 19,20,21,22 of A7. ae

Yes ee 7 Repair Open trace.

Note: Some 5200 2-port boards have pins 1,8,9,10 and 11 of A7 jumpered together on the solder side of the PCB. Future PCB's will incorporate this jumper. Do not add these jumpers to the 5200 2-port board.

CX5200 Field Service Manual 4A-22

Page 107

KEYBOARD TROUBLESHOOTING (Continued)

I No | Is there +5 VDC on Replace A27. BP STeoon Pins 4, 5 and 14 of A27?

Yes No —— _ 5 Swapout

  • a9 Defective A5 or open
  • Alo traces from A5 to A27.

Is the problem Yes repaired? Repair

No or

Check capacitors and resistors on Pins 1-8 of Port 1 for proper value and operation. Replace if defective. Replace

CX5200 Field Service Manual 4A-23 Changed by ECN #0036 6/21/83

Page 108

KEYBOARD TROUBLESHOOTING (Continued)

<>

Yes Does Port 2 pass?

Check capacitors and resistors on Pins 1 & 4 of Port 2. Replace if defective.

CX5200 Field Service Manual 4A-24

Page 109

SECTION 5

4-PORT 5200 SYMPTOM CHECKLIST

The Symptom Checklist is designed to assist the experienced technician arrive at a rapid diagnosis for model 5200 problems. The checklist is not intended to replace the Diagnostic Flowcharts as the primary troubleshooting guide, but rather, to supplement the flowchart. To save you time, Diagnostic Flowchart entry points are indicated on the checklist where applicable.

SYMPTOM

Solid Colored Screen

Vertically Lined Screen

Snowy Screen

Warped Picture (Sync Loss)

No Color

Weak Color

Audio Failures

Only a Few Tones Fail SOLID COLORED SCREEN

POSSIBLE CAUSES

U7,U2,U3,U5,Y1,Q1,Q2,VRI

J1,U2,U3,U5,U7 or open or shorted data or address line

VIDEO FAILURES

VR2,U29(A26)* R.F. Module

RF Module,U!,U5, U3

COLOR FAILURES

U5,Q3,C9,CII,Y1

Q3,C11,C9,R29,R32

AUDIO FAILURES

U7,Q4,C14,C13,LI

U7 FLOWCHART ENTRY POINT

Pg. 4-2

Pg. 4-2

Pg. 4-9

Pg. 4-13

Pg. 4-14

Pg. 4-14

Pg. 4-27

Pg. 4-27

*U29 is chip designation on PCB #CA018087; A26 is chip designation on PCB #CA020108. If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 5-1 Changed by ECN #0036 6/21/83

Page 110

4-PORT 5200 SYMPTOM CHECKLIST (Cont.)

CONTROLLER FAILURES

FLOWCHART SYMPTOM POSSIBLE CAUSES ENTRY POINT

Joystick does not work PORT,U5,U7,C91-C106, Pg. 6-3 R106-R113

Keypad does not work PORT,U9-U12 Pg. 6-4

Fire Button does not fire PORT,U5,RI14-R117,C107-C110 Pg. 4-20 or 4-21

***NOTE*** If you are servicing a unit containing PCB CA020108, chip designators have been changed from U to A.

CX5200 Field Service Manual 5-2

Page 111

SECTION 5A

2-PORT 5200 SYMPTOM CHECKLIST

The Symptom Checklist is designed to assist the experienced technician to arrive at a rapid diagnosis for 2-Port 5200 problems. The checklist is not intended to replace the Diagnostic Flowchart as the primary troubleshooting guide but to supplement the flowchart. To save you time, Diagnostic Flowchart entry points are indicated on the checklist where applicable.

SYMPTOM POSSIBLE CAUSES

SOLID COLORED SCREEN FLOWCHART ENTRY POINT

Solid Colored ScreenA7,A2,A3,A5,A7,Y1,Q1,Pg. 4A-2

Q2, VRI

Vertically Lined ScreenJ1,A2,A3,A5,A7 or open orPg. 4A-2

shorted data or address line

VIDEO FAILURES

Snowy ScreenVR2,A26, RF Module,Pg. 4A-10

Jack, Cable

Warped PictureRF Module,Al,A5,A3Pg. 4A-13

(Sync Loss)

COLOR FAILURES

No ColorA5,Q3,C9,C11,Y1Pg. 4A-14
Weak ColorQ3,C11,C9,R29,R32Pg. 4A-14

AUDIO FAILURES

Audio FailuresA7,Q4,C14,C13,L1Pg. 4A-17
Only a Few TonesA7Pg. 4A-17

Fail

CX5200 Field Service Manual SA-1 Changed by ECN #0036 6/21/83

Page 112

2-PORT MODEL 5200 SYMPTOM CHECKLIST (Cont.)

SYMPTOM

Joystick does not work

Keypad does not work

Bottom Fire Button does not fire

Top (Softfire) Fire Button does not fire

CX5200 Field Service Manual CONTROLLER FAILURES

POSSIBLE CAUSES

PORT,A5,A7,C91-C106, R106-R113

PORT A7,A9-Al1

PORT,A5,RI14-R117, €107-C110

PORT, A7,A8,A2 multiplexer.

5A-2 FLOWCHART ENTRY POINT

Pg. 6-3

Pg. 6-4

Pg. 4A-18

Pg. 4A-19

Page 113

SECTION 6

GAME CONTROLLER

The following pages contain descriptions, schematics and test procedures for the Model 5200 Game Controller.

Overview

The Model 5200 game controller consists of:

The Joystick The Keypad The Fire Buttons The Select Buttons

Refer to Figure 6-1 for the following discussion of the game controller parts.

Select Buttons

Flex Circuit

Ch db: Figure 6-1. Model 5200 Game Controller. ECNIHOO32 CX5200 Field Service Manual 6-1 6/21/83

Page 114

Joystick

The Joystick assembly contains two pots set in the bottom controller case. Two slides (actuator plates) in the top controller case move the pot arms into position when the player moves the joystick. NOTE: For proper operation, the pot arms must be aligned correctly. See Page 6-8 for Pot Arm Alignment Procedures.

The key pad, fire buttons and select buttons operate via a flex circuit.

Key Pad

The key pad is a series of 12 buttons which are used to enhance game play.

Fire Buttons

The game controller has two top fire buttons (one left, one right) and two bottom fire buttons (one left, one right). The bottom fire button (either side) is the one most frequently used.

Select Buttons

The Select Buttons and their functions are:

Start-starts the game being played.
Pause-temporarily stops the game during play.
Reset-permanently stops game play until the Start button is pressed.

Check the key pad functions using Page 6-3, CONTROLLER TESTING USING THE 5200 CONSOLE.

Check the top fire buttons by following the procedure for CONTROLLER TESTING WITHOUT A 5200 CONSOLE on page 6-5.

Check the bottom fire buttons by pressing them separately while in the POKEY ADJUST test. If they are working properly, the screen will display the selection menu.

If the fire buttons are found defective, use Page 6-6 ,Failures, to troubleshoot.

CX5200 Field Service Manual 6-2

Page 115

CONTROLLER TESTING USING THE 5200 CONSOLE

Equipment Needed:

Known-good Model 5200 console (properly adjusted) Known-good Model 5200 controller Color T.V. set (properly adjusted) Diagnostic Cartridge (version 1.1) Ohmmeter

Procedure: (Using 1.1 Diagnostic Cartridge)

1) Set up the 5200 console witha TV, the 1.1 diagnostic cartridge inserted, and a known-good controller in port 1.

  • Press key 5 and then press START to bring up the Pokey Adjust Screen.
  • Remove the known-good controller and insert the controller to be tested into port 1.
  • Move the controller joystick to position 1, as illustrated in Figure 6-2 below. The readings on the screen should be less than 25 for Port | (Port 1 - Horizontal and Vertical).

cr r]

L] Position 1 LJ

|X Joystick

Position 2|

Figure 6-2. Joystick Positions 1 & 2

CX5200 Field Service Manual 6-3 Changed by ECN #0036 6/21/83

Page 116
  • Move the controller joystick to position 2, as illustrated in Figure 6-2. The readings on the screen should be greater than 190 for port |.
  • Slowly move the joystick back and forth between positions 1 and 2 and verify that the readings increase and decrease evenly on the screen. There should be no extreme or sudden changes.
  • Press the keys in the order given on the chart below. As you press each key, watch the screen to verify that the correct letter is displayed in the KB-1 column (see chart below).

KEY KB-1 Readings

START Cc PAUSE SELECT

CO kDONDAUFUN DOPWVHMNDAUVFYNKE MD s

If this test fails, go to Page 6-6, FAILURES.

  • Press one of the bottom fire buttons and the POKEY Adjust Screen should be replaced by the menu.
  • Select the POKEY Adjust Test again (Press 5 and then START).
  • Press the other bottom fire button and the POKEY Adjust Screen should be replaced by the menu.

If the fire buttons are defective, use the FAILURES section on page 6-6 to troubleshoot them.

To check the top fire buttons, go to Step 3 of the CONTROLLER TEST WITHOUT A 5200 CONSOLE, Page 6-5. .

  • This concludes the controller test.

CX5200 Field Service Manual 6-4

Page 117

CONTROLLER TESTING WITHOUT A 5200 CONSOLE

Special Equipment Needed:

Procedure: An Ohmmeter

Use Figure 6-2 on Page 6-3 as reference for Steps | and 2.

Top Fire Button Bottom Fire Button Start Pause Reset

HO KWON DUEWN 1)

2)

3) Move the controller joystick to position 1. Use an Ohmmeter to determine the pot readings through the cable (cable connector Pins 11 & 9 and 10 & 9). The pot reading should be no greater than 50K ohms.

Move the controller joystick to position 2. The pot reading through the cable should be at least 430K ohms greater than in position | (cable connector pins 10 & 9 and 11 & 9).

To check the switches you must connect the leads of the ohmmeter to the pin numbers given below. Without the button depressed it should show infinite resistance (open circuit). With the button depressed it should show less than 50K ohms resistance. Be sure to press the two fire buttons (left and right sides) separately to make sure they both work (see Figure 6-3 on page 6-6 for pin locations).

Controller Pin Numbers

as @ GF COO OUUWUDHDANYNNE SER Peo Seeeseseseeee ENBWENVENVWENWUDN

Failures can be repaired using pages 6-6 through 6-10.

CX5200 Field Service Manual 6-5 Changed by ECN #0036 6/21/83

Page 118

FAILURES

If one key pad key fails, check the 12 key switch set for contamination and clean if necessary. If there is no contamination, replace the Flex Circuit Pad.

If more than one key pad key fails or if the joystick or the fire buttons are not functioning properly:

  • Determine if the controller cable is defective (See Table 6-1).
  • If the controller cable is not defective:
  • Replace the flex circuit pad; or,
  • Align or replace the pots. (See Page 6-8).
NOTE: Pots must be aligned if replaced.

To use Table 6-1 to check the controller cables:

For each failed key, check the continuity from the cable connection pin (column 1) to the flex circuit pad pin (column 2). Note that each key is listed in two places under Failed Key.

Cable Connector Pins are numbered as shown in Figure 6-3.

87654 00000 000 Oo000000 15 1413 12 i 109

Figure 6-3. Cable Connector Pins

Flex circuit pad pins are numbered 11 (left) to 1 (right) as viewed with controller in normal position for game play.

CX5200 Field Service Manual 6-6

Page 119

Table 6-1. Game Controller Continuity Check

Failed Key

1(S1), 4(S4), 7(S7), *(S10) 2(S2), 5(S5), 8(S8), 0 (S11) 3(S3), 6(S6), 9(S9), # (S12) 1(S1), 2(S2), 3(S3), Start (S13) 4(S4), 5(S5), 6(S6), Pause (S14) 7(S7), 8(S8), 9(S9), Reset (S15)

  • (S10), O(S11), # (S12) Start (S13), Pause (S14), Reset (S15) Softfire (Top Fire Button)(S16, S17) not presently used in games Trigger (Line) (Bottom Fire Button) (S18,S19)

Horizontal control on joystick does not work (Pot 2)

Vertical control on joystick does not work (Pot 1)

CX5200 Field Service Manual 6-7 Column | Cable Connector Column 2 Flex Circuit Pad

  • Pin 3
  • Pin 2
  • Pin 1
  • Pin7
  • Pin6
  • Pin 5
  • Pin 8
  • Pin 4
  • Pin 15
  • Pin 14
  • Pin 13
  • Pin 14

1)10&9

Nl &9

  • Pin &
  • Pin7
  • Pin 6
  • Pin9
  • Pin 5
  • Pin 4
  • Pin 3
  • Pin 10
  • Pin 1 and
  • Pin 11
  • Pin 2 and
  • Pin LL

Changed by ECN #0036 6/21/83

Page 120

POT ARM ALIGNMENT PROCEDURE

If you have not already done so, determine if the controller cable is defective (see Table 6-1). If the cable is not defective, continue with the following steps. Use Figure 6-4 as reference for steps 1 through 3.

  • Disassemble the controller and remove arm from wiper shaft on pot.
  • Adjust wiper shaft on pot so that reading between terminals #2 and #3 is 5K -20K Ohms.
  • Position arm on wiper shaft as shown below; position A.

Figure 6-4. Pot and Arm Assembly

  • Reassemble the controller (refer to Page 6-10, CONTROLLER DISASSEMBLY/ASSEMBLY.
  • Move the controller joystick to position | (refer to Figure 6-2). Use an Ohm meter to determine the pot readings through the cable (cable connector Pins 11 & 9 and 10 & 9). The pot reading should be no greater than 50K Ohms.
  • Move the controller joystick to position 2 (refer to Figure 6-2). The pot reading through the cable (connector Pins 10 & 9 and 11 & 9) should be at Jeast 430K Ohms greater than in position 1.

CX5200 Field Service Manual 6-3

Page 121
  • If this test fails:
  • Replace the pots if they have not already been replaced.
  • Replace the actuator plates if the pots have already been replaced.
NOTE: The actuator plates must be replaced as a complete unit which includes the two actuator plates and the slide block (see Figure 6-5).

r | Opening for Pot Acm |

Slide Block Top ‘Actuator Plates mo Botte

Opening for Pot Arm 2

Figure 6-5. Controller Top (Underside)

CX5200 Field Service Manual 6-9 Changed by ECN #0036 6/21/83

Page 122

CONTROLLER DISASSEMBLY/ASSEMBLY

Disassembly

  • To remove the select switches:

e Slide a flathead screw driver under the select switch bezel between switches and pry out the bezel (See Figure 6-6).

e Remove the switches.

——— Joystick Handle

Flathead Screwdriver

by Fire Buttons Pivot Shaft————_>>

Fire Buttons

Figure 6-6. Select Switch Bezel Removal

  • Remove the three screws from the bottom controller case.
  • Separate the top controller case from the bottom controller case. The flex circuit and key pad can now be removed.

4a Remove the two fire buttons on each side by pulling them up.

At this point you can check or replace the Flex Circuit Pad and pots, if necessary.

  • Use the 5200 Controller Knob Puller Tool (FC100214) to remove the joystick handle.

Push the knob shaft into one of the corners of the top housing opening. Push down the boot with the tool to expose the shaft. Push the tool toward the shaft until the shaft is inside the notch of the tool's head (See Figure 1). Now, gently lever the tool, and the knob will pop off.

NOTE: By using care, you will not damage the boot during this process. Be sure to note position of actuator plates and slide block for replacement.

CX5200 Field Service Manual 6-10

Page 123

Figure 6-7. Controller Knob Removal Assembly

  • To replace joystick:

e Place boot in position on ‘outside of top controller case. Position actuator plates and slide block in underside of top controller case. e From underside, place pivot shaft through holes in slide block and boot. e From top, push joystick onto pivot shaft.

  • Replace the fire buttons and place the key pad on the support plate (refer to Figure 6-1).
  • Position the pot arms as shown in Figure 6-8.

[e) fe)

Figure 6-8. Pot Arm Positions for Assembly

CX5200 Field Service Manual 6-11 Changed by ECN #0036 6/21/83

Page 124

4 Place the Select Switches' flex strip through the opening at the left of its well.

  • Position the top controller case on the bottom controller case. Be sure that:

e The actuator plates are correctly positioned in the top controller case (refer to Figure 6-5). e The pot arms are set into the holes in the actuator plates (refer to Figure 6-5). e The joystick pivot shaft sets in the well located between the two pots.

  • Replace and tighten the three screws which hold the top and bottom controller case together.
  • Replace the select switches by placing them on top of the function key pad and pressing the bezel into position on top of them.

CX5200 Field Service Manual 6-12

Page 125

CABLE ASSY or Lae WHT/ORN Col STB 4 Pt 7 T Ve START | PAUSE “| 1 | L 1 L ~ is O- OSI40~ 0515 | I L | \ | . ' eI WHT/BLK ColsTB | |i, 7>! WHT Col STB ls? 1 7 L 4 : ' : Col STB ' GRY 2. co 7 qs! OF 2 s2 0-4 4 $30 ‘95-1 WHT/RED Row Data | v fi 1 ' ' ! DissiO7 peee piseion 5 ' vio Row Data | 4 1 1 1 4 1 ! ? Ss7 OF iJ $8 O-+4 "4 $9 0-4 ai | BLU Row Data 1 s 1 1 1 i) 1 g siocH osu eH gsizo- Pee GRN Row Data | B i] i] SFA SFB ' | a a fl ' Qsic fo} psir ° rset ORN Gnd 155 ral WHT/GRN Softfire | [' 314 HFA HFB 1 (Top Button) | a a a \ ' osi8 9si2o \ a ' eit YEL rigger 1 3 7 (Bottom Button) ' x POT BRN Pot 2__|. ey re Y Pot RED Pot | —— cav | [1 , BLK as +tts9 U SLIDE CONNECTORS

Figure 6-9. CX52 Game Controller Schematic

CX5200 Field Service Manual 6-13 Changed by ECN #0036 6/21/83

Page 126

SECTION 7

CX53 TRAKBALL

Section 7 provides the information necessary to troubleshoot and repair the CX53 Trakball which is used with the model 5200. The following pages contain descriptions, test procedures, diagnostic flowcharts, a symptom checklist, disassembly/assembly instructions and a parts list for the CX53 Trakball. The schematic and silkscreen are included separately.

This section is organized as follows:

Page Information

7-1 through 7-4 An overview and_ general description of the CX53 Trakball.

7-5 and 7-6 Theory of Operation and Block Diagram

7-7 through 7-26 Test Procedures, Diagnostic Flowcharts and Symptom Checklist

7-27 through 7-30 Disassembly/Assembly Procedures

7-31 and 7-32 The CX53 Parts List

The Trakball Schematic and Silkscreen accompany this manual.

OVERVIEW

The CX53 Trakball is an analog controller which can be substituted for the joystick on several game cartridges.

It is composed of an outer case which houses the keypad PC board, the main PC board, the roller shaft assemblies, an idler shaft assembly and a cue ball. Use Figure 7-1 and 7-2 as reference for the following discussion of Trakball parts.

CX5200 Field Service Manual 7-1

Page 127

Keypad PC Board

  • Keypad

START, PAUSE, RESET BUTTONS

1 ‘ [== Fire Buttons Keypad

Fire Buttons

Opening for Cue Ball

Figure 7-1. Top Cover Assembly

CX5200 Field Service Manual 7-2

Page 128

C) <— Cue Ball -_" Shaft Assembly --fpF

Main PC Board

Roller Shaft Assembly Roller Shaft Assembly i

Figure 7-2. Bottom Cover Assembly

CX5200 Field Service Manual 7-3

Page 129

Quter Case

The outer case consists of a top and a bottom plastic cover which are held together by 5 phillips head screws.

At the base of the bottom cover is a cable wrap post for cord storage.

Top Cover

The top cover provides the following (visible from the outside):

an opening in the center for the cue ball.

the START, PAUSE and RESET buttons. Their functions are:

START - is used to start the game being played.

PAUSE - temporarily stops the game during play.

RESET - permanently stops game play until the Start button is pressed.

Two conductive rubber keypads; one on each side of the console. The two keypads are identical - one is for left handed players; the other is for right handed players. The use is the same as the keypad on the regular Model 5200 controller.

Two identical sets of fire buttons (for use by right handed or left handed players). The two buttons closest to the cue ball are the same as the bottom fire buttons on the regular Model 5200 controller. The two buttons closest to the outside of the console are the same as the top fire buttons on the regular Model 5200 controller.

The underside of the top cover houses the keypad PC board. All of the buttons make contact against this board. The fire buttons are dome type. The remaining buttons (the START, PAUSE, RESET and the keypad buttons) are all the conductive rubber type.

Bottom Cover

The bottom cover provides:

an opening at the rear for the game cable

the main PC Board

two roller shaft assemblies each consisting of:

  • a roller shaft
  • 2 bearings
  • a slotted encoding wheel an idler shaft assembly

a cue ball

CX5200 Field Service Manual 7-4

Page 130

THEORY OF OPERATION

For the following discussion, reference the lower PC board assembly schematic. Since both X and Y circuit operation is identical, refer to the X circuit for this description.

The CX53 Trakball is a 2-channel D to A converter which translates optically coupled clocks into analog currents. The current sources or sinks into the two paddle line inputs used for X-Y control in the 5200. Figure 7-3 is a function block diagram to illustrate the following information.

When the cue ball is spun, the two roller shafts rotate. Each shaft has a slotted encoding wheel at one end which interrupts the two light sources in the optocoupler for that channel. This produces a pair of alternating voltage wave forms from the photo-transistors in the optocoupler (U2).

Comparator Al straightens the signals from Ul into 5V square waves and feeds them to A2 and A5. These two clock waveforms are approximately 90° out of phase. This allows correct direction sensing, depending upon which clock leads the other. A2 senses which leading edge of the two clocks is coming first, thus determining direction. _A5 combines the two clocks into one with doubled frequency, thus increasing resolution. This clock is in turn fed into A3 which sets the clock's pulse width at a constant duration while still allowing the frequency to vary with speed.

The Q and Q outputs from A2 are used to gate the fixed-width pulses from A3 with the directional clockgates (A4). This produces alternating outputs depending upon direction (Left or Right). The current integrator networks on the outputs of A4YA &C and A5B&C then link these gated clocks to the analog input of the 5200 main console.

TP9 & TP1O each should have a ramp waveform approximately 3 volts in amplitude. This ramp waveform is generated in the main circuitry of the 5200 and is controlled by increases or decreases in current caused by the Trakball circuit. When the ball is stationary, the ramp will remain at approximately 3V. When the ball is spun in the "right" or "down" direction an inverted clock siphons current off the corresponding ramp with a net reduction in the slope of the ramp (-600mV max. @ C7 and C8). When the ball is spun in the "left" or "up" direction a positive clock causes positive current integration, with a net increase in the slope of the ramp (+900mV max. @C7 and C8).

The clear line (used for calibration) is held HIGH for normal operation. During initialization the console pulls it LOW. This prevents any ball-generated clocks coming from A3, and allows the static output level to be read and used as a reference reading in determining velocity change.

CX5200 Field Service Manual 7-5

Page 131

yenueyp a2TAJag platy 00ZSXO

“9O-Lk sweaerg x0;g TeQNeAL “€-Z aanBig Ki OPTICAL THRESHOLD DIRECTION DIRECTIONAL ° -—>>-

CLOCK INTEGRATOR

COUPLER COMPARATOR SENSOR GATES po

ur oxa a a AM NETWoRKs |OUTPUT

CLEAR LINE CLOCK CONTROLLED FROM CONSOLE __

DOUBLER ONE-SHOT

AB A3 L |

Page 132

TEST PROCEDURES

Equipment Needed:

a known good Model 5200 console a T.V. set, properly adjusted a Missile Command™M Cartridge a 1.1 Diagnostic Cartridge a Digital Voltmeter

Mechanical Check:

Verify that the ball will spin freely and smoothly in all directions. There should be no excessive noise or vibration. If the ball will not spin freely or is excessively noisy, refer to Flowchart A, page 7-11 of this section.

Keyboard Test:

1)

2)

3)

4) Plug the Trakball into player port #1 of the Model 5200 console.

Insert a 1.1 Diagnostic Cartridge into the Model 5200.

Turn the Model 5200 on and select the POKEY Adjust TEST (Test #5).

If the POKEY Adjust Test cannot be selected using the trakball (due to keyboard failure), use a Model 5200 controller to select the test. When the test has been selected, unplug the Model 5200 controller and plug in the Trakball to continue testing.

Test all functions of the START, PAUSE, and RESET buttons and the Keypads:

Table 1-1 shows the correct display for each of the buttons.

CX5200 Field Service Manual Table 7-1 Keyboard Test Display

Button/Keys Display

1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 0 ie) x A # B START S PAUSE D RESET E}

“ ' N

Page 133

If the START, PAUSE or RESET buttons fail, go to Flowchart B, page 7-12 of this section.

If the Keypad(s) fail(s), go to Flowchart BX, page 7-13 of this section.

Trakball and Firebutton Test:

1)

2)

3)

4) Insert the Missile Command cartridge into the Model 5200.

Turn the Model 5200 on and press START.

By spinning the ball at a moderately slow speed, verify that it will cause the cursor (crosshairs) to move in any direction. Be sure that it moves to all extremes of the screen (up, down, left, right, diagonal, and circular motions).

NOTE: When moving in diagonal or circular motions, the cursor will move in slight "steps". This is due to the type of programming used and should not be considered a trakball failure (see Figure 7-4).

Diagonal Motion Circular Motion Figure 7-4. Diagonal or Circular Motion.

NOTE: If more time is required than the attack wave allows, simply press START as needed.

For Cursor left/right failures, go to Flowchart C, page 7-14 of this section.

For Cursor up/down failures, go to Flowchart D, page 7-19 of this section.

Move the cursor to the right border of the screen. Spin the ball as fast as possible by hand in the right direction. This tests for "directional dropouts". While spinning the ball as fast as possible to the right, the cursor should remain on the right border. There should be no movement to the left.

Repeat this test for the left, up, and down directions. For Left/Right failures, go to Flowchart E, page 7-23. For up/down failures, go to Flowchart F, page 7-24.

CX5200 Field Service Manual 7-8

Page 134
  • Verify that a missile fires each time either of the fire buttons (Trigger) closest to the cue ball is pressed. Be sure to test both left and right fire buttons.

If a failure occurs, go to Flowchart M, page 7-25 of this section.

  • Disconnect the trakball from the Model 5200 console. Insert one probe of a Digital Voltmeter into pin 14 of the trakball player port plug. Insert the other probe into pin 15. When either of the outside (Softfire) firebuttons is pressed, the Digital Voltmeter should read less than 200 ohms. Perform this test for both of the outside firebuttons. If a failure occurs, go to Flowchart M, page 7-25 of this section.

CX5200 Field Service Manual 7-9

Page 135

DIAGNOSTIC FLOWCHARTS

The Diagnostic Flowchart is intended to be easy to use and the primary aid when troubleshooting the Model 5200. Follow the prompts in the order presented. When a question is asked, follow the line from the box that best applies to your unit's condition. When that line terminates with a letter inside a circle, locate the letter on a different page and continue the diagnosis. The flowchart leaves nothing to chance, it tells you when to perform a specific test and when to replace components.

SWAP OUT PROCEDURE

At many places in the diagnostic flowchart, a box tells you to "swap out" a component, a chip, or a number of chips in a particular order. The "swap-out" instruction means that you should replace the indicated components (one at a time) with a known-good component of the same type. The unit should then be tested with the new, known-good component in place to see whether the swap out solved the problem being checked. If the swap out did not fix the problem, leave in the new chip and swapout the next. Repeat this procedure for the rest of the swapout. Once the unit properly functions, reinstall the removed IC's to determine which are actually defective.

NOTE: If sockets or components are replaced, trim leads as close to PC Board as possible (See Silkscreen - shaded areas indicate which leads to trim. Only trim leads in shaded areas as close to board as possible).

REPLACE IN ORDER

The "replace in order" instruction means that you should replace the components indicated in the order listed until the result called out in the previous block is obtained.

X - Some lines terminates with an X inside a circle. When this occurs, return to the beginning of the test sequence (Mechanical Check page 7-7).

If you have questions or require further information, call your Atari Techline Specialist.

Inside California (800) 672-1466

Outside California (800) 538-1535

CX5200 Field Service Manual 7-10

Page 136

The problem is probably contamination on the cue ball and roller shafts. Clean all contact surfaces with isopropyl alcohol. MECHANICAL OPERATION

cS

Remove the top housing.

Remove the cue ball.

Spin the idler shaft. Does it roll freely with no excessive noise? No

Yes Replace the idler shaft assy.

Is either or both of the encoding w! contac’ t with the optocoupler? heels making | Yes

No

Spin the roller shafts. Is the PC Board seated properly? (Corners where Ul & U2 are mounted should be flush with the bottom cover). Yes

No

Seat the PCB Board Try to straighten encoding wheels. If they cannot be straightened, replace the entire roller assembly.

properly.

Yes} Do the roller shafts

bee} roll freely with no excessive noise.

No

Replace the entire defective roller shaft assy.

> ~<

Return to beginning of Test Sequence

CX5200 Field Service Manual 7-11

Page 137

KEYBOARD TROUBLESHOOTING (START, PAUSE, RESET BUTTONS)

i

Do the START, PAUSE & RESET buttons work properly? No Perform game cable continuity check. (See chart) Is the cable OK? Replace the cable assy.

Yes

Go to Step 4 of Test Procedures, Page 7-7. Yes

Clean the upper PC Board and the START, PAUSE & RESET buttons.

Do the START, PAUSE & Swapout: RESET buttons now work | No } 1) Buttons

properly? 2) PC Board

Yes

Go to Step 4 of Test Procedures, Page 7-7.

Game Cable Continuity Check

Using a Digital Voltmeter, check the continuity from Jl (column 1) on the upper PC Board to the game cable port connector (column 2).

Key

START, PAUSE, RESET START, 1,2,3 PAUSE, 4,5,6 RESET, 7,3,9 a7 4,7,* 5,8,0 69,4 995i a)

Ji Pin #

wNUENee

CX5200 Field Service Manual (2)

Game Cable Port Connector Pin #

HNUuans

Page 138

KEYBOARD TROUBLESHOOTING (KEYPADS)

<>

. Yes | Clean the upper PC Did just | keypad fail? Board and the failed keypad. No

Perform game cable Yes |Go to next step in Test continuity check. ees ae =4Procedures, Trakball and (ee chart) Firebutton Test, Page 7-8. No

by Swapout: Replace the game 2 weap outy ar Is the cable OK? 1) Keypad vee 2) PC Board

Clean the upper PC Go to Step 4 of Board and both keypads. Test Procedures, Go to Step 4 of Page 7-7. Test Procedures, Page 7-7. Yes [Do both keypads now work properly?

No

Swapout:

  • Keypads
  • PC Board

Yes [Do both keypads now

  • work properly?

No Go to next step in Test Go to Step 4 of Procedures, Trakball & Replace game cable. Test Procedures, Firebutton Test, Page 7-8.| Page 7-7.

Game Cable Continuity Check

Using a Digital Voltmeter, check the continuity from JI (column 1) on the upper PC Board to the game cable port connector (column 2).

WM (2)

Game Cable Port Key Ji Pin # Connector Pin # START, PAUSE, RESET u 4 START, 1,2,3 4 7 PAUSE, 4,5,6 2 6 RESET, 7,8,9 1 5 14,7, * 5 3 2,5,8,0 7 2 36,9, 3 1

CX5200 Field Service Manual 7-13

Page 139

CURSOR LEFT/RIGHT TROUBLESHOOTING

Is unit being supplied with +5VDC? No Replace game cable assembly. Return to beginning Yes of Test Sequence

Does TP5 toggle low No Are there 5V square Replace A2 (OV) when the ball is waves at TPL and TP2 Yes E moved to right and high when the ball is spun? (5V) when the ball is N moved to the left? a

nee Page 7-16

Is TP7 low when the No "7 ball is not in Replace A3. motion? Bo

Yes

Is there a 5V square ST wave at TP7 when the Is there a 5V__ ball is spun? No square wave at pin No (Duty cycle will 4 of A3 when the vary with ball ball is spun? Page 7-17 d). ee | = speed). : Yes Yes No

Does an inverted TP7 “3 a bec at

Y signal appear at pin Live ‘ ce | 3.0f A4 when the ball Yes Page 7-17 is spun right and at — pin 4 of A4 when the Page 7-15 ball is spun left? Swapout A3. J ob . — ———Tr _ ——— "I No | Check C5 and R5. Replace A4. Is there a square Replace defective wave at TP7? components. ~<«t Lves :

Return to beginning of Test Sequence

CX5200 Field Service Manual 7-14

Page 140

No Is there a ramp waveform (approx. 3V) at TP9 when the

Page 7-18

Use Digital Volt Meter to check for open trace or defective R9 or R17. CURSOR LEFT/RIGHT TROUBLESHOOTING (Cont.)

Does a TP7 signal No appear at pin 10 : Replace A5. of AS when the ball is spun left?

Yes

ball is not in motion.

Yes

Return to beginning of Test Sequence

CX5200 Field Service Manual Repair or Replace | Does the TP9 ramp amplitude decrease when the ball is spun to the right?

Yes

to the left? Does the TP9 ramp amplitude increase when the ball is spun Use Digital Volt Meter to check for open trace or defective R10, R18.

Yes

The problem is not in the trakball. The problem may be in the Repair or Replace

Model 5200 console.

Return to beginning of Test Sequence

7-15 Return to beginning of Test Sequence

Page 141

CURSOR LEFT/RIGHT TROUBLESHOOTING (Cont.)

Is the slightly rounded square wave at pin 5 and pin 7 of Al a minimum of 450 MV? (Maximum 2.5V)

Yes Replace Ul.

Is there approx. 400 MV at pins 4 & 6 of Al?

Yes

Replace Al. Is C10 shorted or are R30, R31 open?

Yes

Replace defective component. Replace Al.

& ~ Return to beginning of Test Sequence

CX5200 Field Service Manual 7-16

Page 142

CURSOR LEFT/RIGHT TROUBLESHOOTING (Cont.)

<=>

Ne Is C3 shorted? - Replace AS.

Yes

Replace C3.

—~<t

Return to beginning of Test Sequence

<a>

1] Is th SVDC at No No Yes ‘the base of QI? Is C9 or R25 shorted? Is R8 open? Replace R8. J Yes Yes No

Replace defective Replace Ql. component. Replace game cable.

© Return to beginning of Test Sequence

CX5200 Field Service Manual 7-17

Page 143

CURSOR LEFT/RIGHT TROUBLESHOOTING (Cont.)

Ni Is C7 shorted? S Is R21 open? a — S Replace C7 Replace game cable. Replace R21.

Return to beginning of Test Sequence

CX5200 Field Service Manual 7-18

Page 144

CURSOR UP/DOWN TROUBLESHOOTING

<<

No Is unit being supplied alee Oo ree with +5VDC? 2 L Return to beginning Yes of Test Sequence

Does TP6 toggle low ‘Are there 5V square (OV) when the ball is No waves at TP3 and |¥eS Replace A2. moved up and high TP4 when the ball (5V) when the ball is is spun? moved down? No Yes

Page 7-21

No ae Is TP8 low when the Replace A3. ball is not in motion?

Yes

Is there a 5V square Is there a 5V wave at TP8 when No | square wave at pin he

lat is spun? ne 12 of A3 when ball

cycle will vary wi is spun? ball speed.) p Page 7-22

= Yes

Is there 5VDC at No) pin 13 of A3?

Page 7-20 Page 7-17 Yes

Swapout A3.

Check C6 and R6. Is there a square No] Replace defective wave at TP8? component.

Yes _<— © Return to beginning of Test Sequence

CX5200 Field Service Manual 7-20

Page 145

CURSOR UP/DOWN TROUBLESHOOTING (Cont.)

Page 7-22

to check for open trace} or Defective R11, R19 J No

Repair or Replace

Return to beginning of Test Sequence

CX5200 Field Service Manual <=>

Does an inverted TP8 signal appear at pin 11 of A4 when the ball is spun up and at pin 10 of A4 when the ball is spun down? No

Does a TP8 signal appear at pin 4 of A5 when the ball is spun up?

Is there a ramp waveform (approx. 3V) at TP1O when the ball is not in motion?

Does the TP10 ramp amplitude decrease when ball is spun down?

Does the TP10 ramp amplitude increase when ball is spun up?

The problem is not in the trakball. The problem may be in the Model 5200 console.

R

° to chec! jor defective R12, R20. Replace A4.

Replace A5.

ital Volt Meter for open trace,

Repair or Replace

turn to beginning f Test Sequence

Page 146

CURSOR UP/DOWN TROUBLESHOOTING (Cont.)

Is the slightly rounded square wave at pin 9 & pin 11 of Al minimum of 450MV p-p? (Maximum. 2.5V) Replace Ul.

Is C10 shorted or are R30, R31 open? Is there approx. 4OOMV at pins 8 & 10 of Al? Replace Al.

Yes

Replace defective component. Swapout

  • Al

Return to beginning of Test Sequence

CX5200 Field Service Manual 7-21

Page 147

CURSOR UP/DOWN TROUBLESHOOTING (Cont.)

Is C4 shorted? Replace A5.

Return to beginning of Test Sequence

Replace R22.

Return to beginning of Test Sequence

CX5200 Field Service Manual 7-22

Page 148

LEFT/RIGHT DIRECTIONAL DROPOUTS TROUBLESHOOTING

i

Set oscilloscope sweep time to -2 msec/div. yearn

Is the rounded square wave at pin 5 & pin7 of Al a minimum of No 450 MV? (Maximum Bebe! 2.5V) Ball must be spun at a fast rate.

Does the waveform have a 50/50 duty N cycle? (Minimum “ Replace Ul. acceptable duty cycle: 60/40)

Yes

<< Return to beginning of Test Sequence

NOTE: Make sure the main PC Board is seated properly in the bottom cover. The corners where U1 and U2 are mounted should be flush with the bottom cover.

CX5200 Field Service Manual 7-23

Page 149

UP/DOWN DIRECTIONAL DROPOUTS TROUBLESHOOTING

Set oscilloscope sweep time to .2 msec/div.

Is the rounded square wave at pin 9 and pin 11 of Al a minimum of 450MV p-p? LN°]} Replace U2. (Maximum 2.5V) Ball must be spun at a fast rate.

Does the waveform have a 50/50 duty No cycle? (Minimum acceptable duty cycle: 60/40) Replace U2.

Swapout:

  • AL
  • A2
  • U2

Return to beginning of Test Sequence

CX5200 Field Service Manual 7-24

Page 150

FIREBUTTON TROUBLESHOOTING

Are the dome switches on the upper PC Board damaged? (Inspect visually) Replace the upper PC Board.

Swapout:

  • Cable
  • PC Board (Upper)

Return to beginning of Test Sequence

CX5200 Field Service Manual 7-25

Page 151

SYMPTOM

Noisy operation or ball won't spin freely

Keyboard failure

Fire button failure

Cursor won't move at all

Cursor moves erratically left and right or up and down

Cursor won't move left or right

Cursor won't move up or down

Directional dropouts (left or right)

Directional dropouts (up or down)

Blank screen when trakball is plugged in

CX5200 Field Service Manual SYMPTOM CHECKLIST

POSSIBLE CAUSES

Dirty roller and idler shafts and ball, worn bearings, warped encoding wheels

Dirty keyboard PC board, dirty 12-key switch set, or defective game cable

Damaged dome switches on keyboard PC Board, defective game cable

Ql, A3, defective game cable

A3

U1, Al-A5, C7

U2, Al-A5, C8

U1, PC board not seated properly

U2, PC board not seated properly

C1,C2 or any of the IC's Al-A5 shorted to ground

7-26 FLOWCHART ENTRY POINT

A, Page 7-11

B, Page 7-12

See Chart, Flowchart B, Page 7-12

No Flowchart Entry Point

No Flowchart Entry Point

C, Page 7-14

D, Page 7-19

E, Page 7-23

E, Page 7-23

No Flowchart Entry Point

Page 152

DISASSEMBL Y/ASSEMBLY

Be sure that unit is unplugged from the Model 5200 Console before disassembling to any level.

Refer to Figures 7-1 and 7-2, for the following Disassembly/Assembly.

e Turn the unit upside down and support it so that cue ball doesn't rub against the work bench (See Figure 7-5).

E—Trakball Unit (upside down}

Cue Ball

“Ne Book ‘Table Surface

Figure 7-5. Cue Ball Support

e Remove the 5 phillips head screws from the bottom cover.

e Turn the unit right side up. Lift off the top cover and place it upside down.

° To remove the Keypad PC board (See Figure 7-6):

  • Unplug the |1-pin ribbon cable from the PC board. Be sure to note polarity when unplugging.
  • Carefully pull out on the four retaining clips (top cover) while lifting up on the board.

CX5200 Field Service Manual 7-27

Page 153

ypad PC Board} | | |

° ° [7 =| ° ° Retaining cup LL C), SRretaining Clip

A 4 &

\ /

Figure 7-6. Top Cover (Underside)

To replace the Keypad PC Board:

e Position the board as shown in Figure 7-6. Be sure that PC board is under the notches at the back of the top cover.

e Carefully pull the retaining clips (top cover) far enough away from the PC board to allow the board to slip down and lock into position under the clip.

e Plug in the 11-pin ribbon cable.

To remove the main PC Board: (See Figure 7-7)

e Unplug the 5-pin cable plug (J2). Be sure to note polarity when unplugging.

e Lift and remove the cue ball and the two roller shafts.

e Carefully pull out on retaining clip A and lift the PC board, then pull out on retaining clip B and lift the PC board.

e Remove the PC board.

CX5200 Field Service Manual 7-28

Page 154

NJ Retaining Clip A

<= Jain PC Board

Rethning Clip 8

Figure 7-7. Main PC Board

To replace the main PC Board:

Position the board as shown in Figure 7-7. Be sure that the holes in the board are aligned with the three holding tabs in the bottom cover.

Carefully pull out on retaining clip A, slip the board down and lock it into place under the clip.

Carefully pull out on retaining clip B, slip the board down and lock it into place under the clip.

Plug in the 5-pin cable plug (J2) on the PC board.

To reassemble the console:

Replace the main PC board in the bottom cover.

Replace the cue ball and two roller shafts in the bottom cover. Be sure that the roller shaft bearings and the encoding wheel are seated properly. The bearings fit into the rounded wells at each end of the roller shaft assembly. The encoding wheel fits into the optocoupler slot.

Replace the keypad PC board in the top cover.

Be sure that all cables are plugged in correctly.

Be sure that all springs and keypads are correctly mounted in the top case.

CX5200 Field Service Manual 7-29

Page 155

e Place the top cover over the bottom cover.

e Turn the unit upside down. Support the unit on books to keep the cue ball from rubbing against the work bench.

e Replace and tighten the five phillips head screws in the bottom cover.

CX5200 Field Service Manual 7-30

Page 156

PARTS LIST

LOCATOR DESCRIPTION PART NUMBER

TRAKBALL ASSY CA020194

Top Housing Assy CA020197 Bottom Housing Assy CA020198 Lower PCB Assy CA020140 Roller Shaft Assy CA020583 Cable Assy CA020338

Top Housing Assy CA020197 Top Housing C020195 Name Plate C020193 12-Key Switch Set C018126 Fire Button 020192 Auxiliary Function Keys C018128 Upper PCB Assy CA020287 Spring C012951 Bottom Housing Assy CA020198 Bottom Housing 021096 Roller Shaft Assy CA020583 Idler Shaft Assy CA020582 Ball, 2 1/4" Diameter c020191 Feet, rubber 88-1006 Lower PCB Sub-Assy CA020141 Shaft, Roller 020572 Encoding Wheel 020571 Bearing C020190 cl Cap, Electrolytic Radial 10uf 16V C014392 C2 Cap, Ceramic Axial .luf 50V C014180-19 C3,4 Cap, Ceramic Axial 470pf 50V C014180-07 C5,6,7,8 Cap, Mylar Radial: .luf, 100V C017885 co Cap, Ceramic Axial: .Oluf 50V C014180-18 C10 Cap, Ceramic Axial: .22uf 50V C014181-05 R1-4 Resistor: 3K 1/4W 14-5302 R5,6 Resistor: 12K, 1/4W 14-5123 R7,26-29 Resistor: 10K 1/4W 14-5471 R8 Resistor: 1K 1/4W 14-5102 R9-12 i -2K 1/4W 14-5222 R13-16 3K 1/4W 14-5132 R17,19 3K 1/4W 14-5433 R18-20 Resistor: 30K 1/4W 14-5303 R21,22 Resistor: 180K 1/4W 14-5184 R23,24 Resistor: 240 Ohm 1/4W 14-5241

CxX5200 Field Service Manual 7-31

Page 157

CX53 TRAKBALL

LOCATOR DESCRIPTION

R25 Resistor: 4.7K 1/4W R30 Resistor: LOOK 1/4W R31 Resistor 8.2K 1/4W R32-35 Resistor 430K 1/4W XA1,2,4,5 Socket I.C. 14 Pin XA3 Socket I.C. 16 Pin 32 Connector, Molex 5 Pin U1,2 Optocoupler Ql Transistor, 2N3904 PCB Al 1.C. LM339 A2 I.C. 4013 A3 1.C. 4538 A4& I.C. 4011 A5 1.C. 4030 Cable Assy, 15-wire, 4-feet

CX5200 Field Service Manual 7-32 PART NUMBER

14-5472 14-5104 14-5822 14-5434 C014386-02 C014386-03 020463 020290 34-2N3904 020142 015950 CO14334 020478 014333 020477 CA020338

Page 158

SECTION 8

ATARI CX5200 PARTS LIST

MAJOR ASSEMBLIES

LOCATION DESCRIPTION PART NO.

ATARI VCS CX5200 CA018174-01 (ORIGINAL 4-PORT) (Pkgd.) ATARI VCS CX5200 CA021450-XX (UNIVERSAL 4-PORT) (Pkgd.) PC Board Assy (Main) CA018087 (ORIGINAL 4-PORT) PC Board Assy (Main) CA020108 (UNIVERSAL 4-PORT) Heatsink Assy CA019069 Heatsink Assy (Universal) CA020161 RF Modulator "B" Assy CA012174 Cable Assy CA018218 Top Housing Assy CA018175-01 (Original & Universal 4-Port) Base Assy CA018176-01 (Original & Universal 4-Port)

ATARI VCS CX5200 (Pkgd.) CA021452-XX (2-PORT)

PC Board Assy (Main) (2-Port) CA021374 Heatsink Assy CA020161 RF Modulator "B" Assy CA012174 Cable Assy A003647 PC Board Sub-Assy CA021375 Top Housing Assy (2-Port) CA021 587-01 Base Assy (2-Port) CA021588-XX

ATARI CX522 SWITCH BOX ASSY (Pkgd.) CA020803-01 (ORIGINAL AND UNIVERSAL 4-PORT)

ATARI SWITCH BOX ASSY (2-PORT) CA018233-XX

Balun Transformer C018994

ATARI CX52 CONTROLLER ASSY (Pkgd.) CA018107 (ALL MODELS)

Flex Circuit & Key Pad Assy CA018989 Controller Cable Assy CA018145 Top Housing Assy CA018223 Pot & Arm Assy CA01 8987 Cable Pot Assy CA018988

CX5200 Field Service Manual 8-1 Changed by ECN #0036 6/21/83

Page 159

LOCATION DESCRIPTION PART NO.

CX521 AC/DC POWER ADAPTOR (Pkgd.) C0181 87 (ORIGINAL AND UNIVERSAL 4-POR 1

AC/DC POWER ADAPTOR (Not Pked.) CAO19141-XX (ORIGINAL AND UNIVERSAL 4PORT)

A.C. ADAPTOR ASSY (2-PORT)(PKGD.) CA021673-XX

PC BOARD ASSY (MAIN) CA018087 (ORIGINAL 4-PORT)

NOTE: The Parts List for PC Board Assy (Main) Number CA020108 begins on page 8-5. The Parts List for PC Board Assy (Main) Number CA021374 begins on page 8-8.

C1,2,5,7,8)15-17,21,23-29 Cap. Ceramic Axial .luF (50V) C014181-03 34,47,60,7 3,86 ; C3,4,6,12,18,22, 36,49, 50 Cap. Ceramic Axial .0luF (50V) C014180-18 (oy) Cap. Ceramic Axial L00pF (50V) C014180-03 C10,31,33,55 Cap. Ceramic Axial 47pF (50V) C014179-05 C11,20 Cap. Ceramic Axial LOpF (50V) C014179-03 C13,14 Cap. Polystyrene 820pF (25V) C018621 C19,99-106 Cap. Polyester Radial .047uF (100V) C017518 30,32 Cap. Ceramic Axial 68pF (50V) CO14179-12 C35 Cap. Ceramic Axial 22pF (50V) CO14179-01 C37,38,40,48,51-54,91-98, Cap. Ceramic Axial .001uF (50V) CO14180-17 107-110,124,126,1 31-135 C41,42,119,144 Cap. Tantalum Axial 10uF (20V) CO17516 C43,44 Cap. Polyester Radial .22uF (100V) 010394 C45 Cap. Elec Radial 4700uF (25V) 016033 C56-59,61-72,74-85,87-90 Cap. Ceramic Axial 470pF (50V) CO14179-16 112-115 C111,117,118,120-122,125, Cap. Ceramic Axial .luF (50V) CO14181-03 127,129,1 30,136 C116 Cap. Ceramic Axial .22uF (50V) C014181-05 C138,139,141-143 Cap. Ceramic Axial .LuF (50V) C014181-03 C140 Cap. Ceramic Axial 33pF (50V) C014179-04 RI Resistor 1/4W 470K 14-5474 R2 Resistor 1/4W 100K 14-5104 R3 Resistor 1/4W | Meg 14-5105 R4-7,15,16,27,32,34-37, Resistor 1/4W 4.7K 14-5472 47,55,56,60,69,124 R8& Resistor Variable 500K 19-411504 RO Resistor 1/4W 91 Ohm 14-5910 R10,17-21,30,39,44,50 Resistor 1/4W 1K 14-5102 59,66,96,101 R11,14,68,131 Resistor 1/4W 220 Ohm 14-5221 R12,61 Resistor 1/4W 2.2K 14-5222 R13 Resistor 1/4W 240 Ohm 14-5241 R22,64 Resistor 1/4W 8.2K 14-5822 R23 Resistor 1/4W 82K 14-5823 R24 Resistor 1/4W 39K 14-5393 R25 Resistor 1/4W 20K 14-5203 R26,40 Resistor 1/4W 10K 14-5103 R28 Resistor 1/4W 3.3K 14-5332 CX5200 Field Service Manual 8-2

Page 160

LOCATION DESCRIPTION PART NO. PC BOARD ASSY (MAIN)(Continued) CA018087 (ORIGINAL 4-PORT)

R29,46 Resistor 1/4W 12K 14-5123 R31,43,65,125 Resistor 1/4W 6.8K 14-5682 R33 Resistor 1/4W 510 Ohm 14-5511 R41 Resistor 1/4W 18K 14-5183 R42 Resistor 1/4W 9.1K 14-5912 R45 Resistor 1/4W 15K 14-5153 R48,49 Resistor 1/4W 47K 14-5473 R51 Resistor 1/4W 10 Ohm 14-5100 R52 Resistor 1/4W 5.1K 14-5512 R53 Resistor 1/4W 56 Ohm 14-5560 R54 Resistor 1/4W 560 Ohm 14-5561 R57,58 Resistor 1W 330 Ohm (Metal Film) C018188-02 R62,63 Resistor 1/4W 22K 14-5223 R67 Resistor 1/4W 150 Ohm 14-5151 R70-76,78-95,97-100, Resistor 1/4W 470 Ohm 14-5471 102-105,114-121 R106-113 Resistor 1/4W 1.8K 14-5182 R122 Resistor 1/4W 22 Ohm 14-5220 R123 Resistor 1/4W 390 Ohm 14-5391 R126 Resistor 1/4W 1K (Metal Film) C018974-01 R128 Resistor 1/4W 3.3K (Metal Film) C018974-03 R129,133 Resistor 1/4W 680 Ohm 14-5681 R130 Resistor 1/4W 1.5K (Metal Film) C018974-02 R132 (Alternate listed) Resistor Variable 1K 019103 R132 (Alternate for P/N Resistor Variable 1K 018975 019103) Ul IC CD4050B (HEX CMOS Buffer) C010816 U2 IC 6502 (Modified) C014806 U3 IC ANTIC 012296 U4,15 IC 74LS244 C014313

U5 IC GTIA C014805 U6 IC 74LS139N 018032 U7 IC POKEY C012294 Us IC ROM OS C019156 U9-13 IC 4052 (Analog multiplexer) 017950 U14,28 IC 74LS10 014339

U16,17 IC 74LS258N 019052 U18-25 IC RAM (16K X LD Single Supply) 018082 U27 IC 74LS00 CO14341 U29 IC 4013B (Dual Type D Flip Flop) CO14334 CRI-4 Diode 1N914 31-1N914 Q1,2,5,11,15 Transistor 2N3906 C018991 Q3,8-10,12-14 Transistor 2N3904 34-2N3904 Q4 Transistor 34-2N3563 34-2N3563 Q6,7 Transistor MJE210 C01 8094

CX5200 Field Service Manual 8-3 Changed by ECN #0036 6/21/83

Page 161

LOCATION

Y1 (Alternate listed) Y1 (Alternate for P/N 015510)

LI L2 L3 L4-6 L8 L9,11-16,18

DSL DSI (Part of)

VRI,2 (Part of)

Sl $2

J

Port 1-4

X1,6,9-13, 16-25 X2,3,5,7 X4,15 X8 X14,27-29

VRI,2 VRI1,2 (Part of)

CX5200 Field Service Manual DESCRIPTION

Crystal 3.579575 Mhz (HC-18) Crystal 3.579575 Mhz

PC BOARD ASSY (MAIN)(Continued) (ORIGINAL 4-PORT)

Inductor Variable (0.85-1.2uH) Inductor Axial 2uH Inductor Axial 4.7uH Inductor Axial 22uH Inductor Axial 2.7uH Inductor Ferrite Bead

LED LED Standoff

Voltage Regulator 78M05 (5V)

Switch Slide Channel Select Switch Momentary Push Button

Connector Cartridge PC Board Mount (18/36) Connector Phono Jack

Connector (15 pin)

Socket IC (16 pin) Socket IC (40 pin) Socket IC (20 pin) Socket IC (24 pin) Socket IC (14 pin)

Heatsink/Regulator Assy Heatsink

RF Modulator "B" Assy Cable Assy

Shield Top Shield Bottom

PC Board (J2 mounted on PC Board)

8-4 PART NO.

C015510 C010177

CA018087

010823 010822 C014804 014380 CO018189 C014384

C014776 C018143

CO14348

C012241 C018093

018081

018245

C018013

C014386-03 C014386-09 C014386-05 C014386-07 C014386-02

CA019069 C018140

CA012174 CA018218

019027 019028

C018085

Page 162

LOCATION

Al A2 A3 AS A6 A7 AB A9-13 Alg ALS A16,17 AL8-25 A26 A27

Cl,2,7,8,15-17, 21,23-29,34,47,60 73,86,111,117,118, 121,122,125,127 129,1 30,136,137, 138,139,141,142, 143,147 C3,4,6,12,18,22 36,49,50 co Clo C11,20 C13,14

C19,99-106 C30-33 C35 C37,38,40,48,51 52-54,91-98,107- 110,124,126,131-

C39 C41,42, 119,144 C43, 4d C45 C55,145

CX5200 Field Service Manual DESCRIPTION

PC BOARD ASSY (MAIN) (UNIVERSAL 4-PORT)

5200 Universal PCB Assy Heatsink Assembly LED:DS1 LED Standoff Shield Top Shield Bottom

LC. 4050B 1.C. Custom 6502 1.C. Custom ANTIC 1.C. Custom GTIA 1.C. 74LS139N I.C. Custom POKEY 1L.C. ROM, O.S. I.C. Custom 4052, A9-13 LC. 74LS125 LC. 74LS51 I.C. Custom 74LS258N LC. 16Kx1D RAM Single Supply 1.C. Custom 4013B 1.C. Custom 74LS00

Cap. Ceramic Axial 50V

Cap. Ceramic Axial .0luF, 50V

Cap. Ceramic Axial, LOOpF, 50V Cap. Ceramic Axial, 47pF, 50V Cap. Ceramic Axial, LOpF, 50V Cap. Polystyrene Auto, Insertable, 820pF Cap. Polyester Radial, .047uF,100V Cap. Ceramic Axial, 39pF, 50V Cap. Ceramic Axial, 22pF, 50V Cap. Ceramic Axial, .0001uF, 50V

Cap. Ceramic Axial 68pF, 50V Cap. Tantalum Axial 10uF, 20V Cap. Polyester Radial, .22uF, 100V Cap. Electrolytic Radial, 47uF, 25V Cap. Ceramic Axial, 390pF, 50V

8-5 PART NO.

CA020108

CA020108 CA020161 CO014776 CO18143 019027 019028

C010816 C014806 C012296-XX C014805-XX C0180323 C012294 C019156 017950 C016543 CO019671 C019052 C018082 C014334 CO14341

CO1481-03

CO14180-18

C014180-03 C014179-05 C014179-03 CO018261

CO17518 CO14179-23 C014179-01 CO14180-17

C014179-12 CO017516 C010394 co20121 C014179-24

Changed by ECN #0036 6/21/83

Page 163

LOCATION

C56-59,61-72,74-85 C116 C140 CRI1-7,9-10

J J3

Ll

L2 L3 L4-6 L7,9,10,12-15 L8

Q1,2,5,11,15 Q3,8-10,12-14 Q4

RI R2 R3 R4-7,15,16,27,32, 34-37,47,56,60, 124,136,55 R8 R10, 17-21,30,39 44,59,66,96,50 101,140,141 R11,14,68,131 R12,61,69,135 R13 R22,64 R23 R24 R25 R26,40 R28, 142 R29, 46 R31,43,65,125 R4l R42 R45 R48,49 R51,137 R52 R53 R54

CX5200 Field Service Manual DESCRIPTION

PC BOARD ASSY (MAIN) (Continued) (UNIVERSAL 4-PORT)

Cap. Ceramic Axial, 470pF, 50V Cap. Ceramic Axial, .22uF, 50V Cap. Ceramic Axial, 33pF, 50V Diode: 1N914

Cartridge PCB Mount: 18/36 Contacts Jack, Phono, RF Output, PC Mounted Connector 15 Pin"D" Sub Port 1-4

Inductor Radial Variable: -85-1.2uH, 12.5 Turn Inductor Axial: 2uH Inductor Axial: 2.7uH Inductor Axial: 22uH Ferrite Bead Inductor Axial 2.7uH

Transistor Power PNP:MJE Transistor 2N3904 Transistor 2N3563

Carbon Film Resistor 470K Ohm, 1/4W Carbon Film Resistor 100K Ohm, 1/4W Carbon Film Resistor 1 MEG Ohm,1/4W Carbon Film Resistor 4.7K Ohm 1/4W

Resistor, Pot: 500K, 1/4W Carbon Film Resistor 1K Ohm, 1/4W

Carbon Film Resistor 220 Ohm, 1/4W Carbon Film Resistor 2.2K Ohm, 1/4W Carbon Film Resistor 240 Ohm, 1/4W Carbon Film Resistor 8.2K Ohm, |/4W Carbon Film Resistor 82K Ohm, 1/4W Carbon Film Resistor 39K Ohm, 1/4W Carbon Film Resistor 20K Ohm, 1/4W Carbon Film Resistor 10K Ohm, 1/4W, Carbon Film Resistor 3.3K Ohm, 1/4W Carbon Film Resistor 12K Ohm, 1/4W Carbon Film Resistor 6.8K Ohm, 1/4W Carbon Film Resistor 18K Ohm 1/4W, Carbon Film Resistor 9.1K Ohm 1/4W, Carbon Film Resistor 15K Ohm 1/4W Carbon Film Resistor 47K Ohm 1/4W Carbon Film Resistor 10 Ohm 1/4W, Carbon Film Resistor 5.1K Ohm, 1/4W Carbon Film Resistor 56 Ohm 1/4W Carbon Film Resistor 560 Ohm, 1/4W

8-6 PART NO.

CA020108

CO14179-16 C014181-05 C014179-04 31-1N914

C01 8081 CO18245 018013

010823

C010822 017224 014380 C014384 C0181389

33-2N3906 34-2N3904 34-2N3563

14-5474 14-5104 14-5105 14-5472

19-411504 14-5102

14-5221 14-5222 14-5241 14-5822 14-5823 14-5393 14-5203 14-5103 14-5332 14-5123 14-5682 14-5183 14-5912 14-5153 14-5473 14-5100 14-5512 14-5560 14-5561

Page 164

LOCATION

R57,58 R62,63 R67 R70 R71-76,78-95,97- 100,102-105,114-

R106-113 R122 R123 R126 R128 R129 R130 R132 R134

SI $2

UL XAL,6,9-13, 16,17 18-25 XA2,3,557 XA8 XA14,15,26,27

Yi

CX5200 Field Service Manual DESCRIPTION

PC BOARD ASSY (MAIN) (Continued) (UNIVERSAL 4-PORT)

Carbon Metal Film 182 Ohm, 1W Carbon Film Resistor 22K Ohm, 1/4W Carbon Film Resistor 150 Ohm, 1/4W Carbon Film Resistor 1.5K Ohm, 1/4W Carbon Film Resistor 470 Ohm 1/4W

Carbon Film Resistor 1.8K Ohm, 1/4W Carbon Film Resistor 22 Ohm, 1/4W Carbon Film Resistor 390 Ohm, 1/4W Carbon Metal Film 1K Ohm, 1/4W Carbon Metal Film 3.3K Ohm, 1/4W Carbon Film Resistor 680 Ohm, 1/4W Carbon Metal Film 1.5K Ohm, 1/4W Resistor, Trim Pot: 1K Ohm Carbon Film Resistor 100 Ohm, 1/4W

Switch, Slide: Chan. Sel. Side Arm Switch, SPDT, Momentary, Push Button ON/OFF

Modulator, RF "B" Socket I.C. 16 Pin

Socket I.C. 40 Pin Socket I.C. 24 Pin Socket I.C. 14 Pin

Crystal 3.579575 MHz PART NUMBER

CA020108

C018188-01 14-5223 14-5151 14-5152 14-5471

14-5182 14-5220 14-5391 C018974-01 C018974-03 14-5681 01987 4-02 C019103-XxX 14-5101

C012241 C018093-XX

CAO012174 C014386-03

C014386-09 C014386-07 C014386-02

CO10177-XX

Changed by ECN #0036 6/21/83

Page 165

LOCATION

R132 Sl S2

C1,2,5,7,8,15-17, 21,23-29,34,47,60, 61,73,86, 117,137,121, 122,125,127,129,130, 136,141,138,139,142, 143,147 C3,4,6,12,18,22,36, 49,50 c9 Clo C11,20 C13-14

C19,99,100,105,106 C30-33 C35 C37,38,40,48, 51,54, 91,92,97,98,107, 112,124,126,131, 132,135

CX5200 Field Service Manual DESCRIPTION PART NUMBER

PC BOARD ASSY (MAIN)(2-PORT) CA021374

1.C. 4050B C010816 1.C. Custom 6502 014806 1.C. Custom Antic C012296-XX 1.C. Custom GTIA C014805-XX 1.C. 74LS139N 018032 I.C. Custom POKEY 012294 1.C. ROM O.S, 019156 1.C. 4052 017950 IC. 74LS125 C016543 I.C. 74LS51 019671 I1.C. 74LS258N 019052 1.C. RAM 16K X 1D Single Supply C01 8082 I.C. 4013B 014334 I.C. 74LS00 CO14341 Power Jack, Rt Angle CO14715 Heatsink Assembly CA020161 Modulator, RF "B" CA012174 Resistor, POT, 500K, 1/4W 19-411504 Resistor, Trim POT, 1K C019103-XX Switch, Slide Channel Select Side Arm C019702-XX Switch, SPDT, Mmntry Psh Btn, On/Off C018093-XX Pop Rivets C014796 Shield Top 019027 Shield Bottom 019028

Cap, Ceramic Axial, .luf, 25V C014181-03

Cap, Ceramic Axial, .Oluf, 50V C014180-13

Cap, Ceramic Axial, 100pf, 50V C014180-03 Cap, Ceramic Axial, 47pf, 50V C014179-05 Cap, Ceramic Axial, 10pf, 50V C014179-03 Cap, Polystyrene Auto Insertable, 018261 820pf, 25V Cap, Polyester Radial, .047uf, 100V CO175138 Cap, Ceramic Axial, 39pf, 50V C014179-23 Cap, Ceramic Axial, 22pf, 50V C014179-01 Cap, Ceramic Axial, .00luf, 50V CO14180-17

8-8

Page 166

LOCATION

C39 C4142, 119, 144 43,44 C45 C56-59,69-72,74- 77,87-90,110,115 C16 C140 C145,55 RL R2 R3

R4-7,16,27,32,34- 37,47,55,56,60,124,

R9 R10,17-21,30,39 44,59,66,50,101 140,141 R11,14,68,131 R12,61,69,135 R13 R22,64 R23 R24 R25 R26,40 R28, 142 R29,46 R31,43,65,125 R33 R4l R42 R45 R48, 49 R51,137 R52 R53 R54 R57, 58 R62,63 R67 R70

CX5200 Field Service Manual DESCRIPTION

PCB SUB-ASSY (2-PORT)

Cap, Ceramic Axial, 68pf, 50V Cap, Tantalum Axial, 10uf Cap, Polyester Radial, .22uf, 100V Cap, Electrolytic Radial, 47uf, 25V Cap, Ceramic Axial, 470pf, 50V

Cap, Ceramic Axial, .22uf, 50V Cap, Ceramic Axial, 33pf, 50V Cap, Ceramic Axial, 390pf, 50V Res., Carbon Film, 470K Ohm, 1/4W Res., Carbon Film, 100K Ohm, 1/4W Res., Carbon Film, 1 Meg Ohm, 1/4W

Res., Carbon Film, 4.7K Ohm, 1/4W

Res., Carbon Film, 91 Ohm, 1/4W Res., Carbon Film, 1K Ohm, 1/4W

Res., Carbon Film, 220 Ohm, 1/4W Res., Carbon Film, 2.2K Ohm, 1/4W Res., Carbon Film, 240 Ohm, 1/4W Res., Carbon Film, 8.2K Ohm, 1/4W Res., Carbon Film, 82K Ohm, 1/4W Res., Carbon Film, 39K Ohm, 1/4W Res., Carbon Film, 20K Ohm, 1/4W Res., Carbon Film, 10K Ohm, 1/4W Res., Carbon Film, 3.3K Ohm, | /4W Res., Carbon Film, 12K Ohm, |/4W Res., Carbon Film, 6.8K Ohm, 1/4W Res., Carbon Film, 510 Ohm, 1/4W Res., Carbon Film, 18K Ohm, 1/4W Res., Carbon Film, 9.1K Ohm, 1/4W Res., Carbon Film, 15K Ohm, 1/4W Res., Carbon Film, 47K Ohm, 1/4W Res., Carbon Film, 10 Ohm, 1/4W Res., Carbon Film, 5.1K Ohm, 1/4W Res., Carbon Film, 56 Ohm, 1/4W Res., Carbon Film, 560 Ohm, 1/4W Res., Carbon Metal Film, 330 Ohm, |W Res., Carbon Film, 22K Ohm, 1/4W Res., Carbon Film, 150 Ohm, 1/4W Res., Carbon Film, 1.5K Ohm, 1/4W PART NUMBER

CA021375

CO14179-12 C017516 C010394 020121 C014179-16

C014181-05 C014179-04 C014179-24 14-5474 14-5104 14-5105

14-5472

14-5910 14-5102

14-5221 14-5222 14-5241 14-5822 14-5823 14-5393 14-5203 14-5103 14-5332 14-5123 14-5682 14-5511 14-5183 14-5912 14-5153 14-5473 14-5100 14-5512 14-5560 14-5561 C018188-02 14-5223 14-5151 14-5152

Changed by ECN #0036 6/21/83

Page 167

LOCATION

R71-74,80-84, 88-91,102-105, 114,117,118, 121 R106,109,110,113 R122 R123 R126 R128 R129 R130 R133, 134 ql

Yi CRI-10 DS1

Li

L2 L3 L4-6 L9,7,12-15,10

XA1,6,9-11,16,17, 18-25 XA2,3,5,7 XA8 XA14,15,27,26 Q1,2,5,11,15 Q3,8,9,10,12,13,14 Q4 Q6,7

CX5200 Field Service Manual DESCRIPTION

PCB SUB-ASSY (2-PORT) (Continued)

Res., Carbon Film, 470 Ohm, 1/4W,

Res., Carbon Film, 1.8K Ohm, 1/4W Res., Carbon Film, 22 Ohm, 1/4W Res., Carbon Film, 390 Ohm, 1/4W Res., Carbon Metal Film, 1K Ohm, 1/4W Res., Carbon Metal Film, 3.3K Ohm, 1/4W Res., Carbon Film, 680 Ohm, 1/4W Res., Carbon Metal Film, 1.5K Ohm, 1/4W Res., Carbon Film, 100 Ohm, 1/4W Cartridge, PCB Mnt, 18/36 Contacts Connector,15 Pin "D" Sub Port 1-2 Crystal,3.579575 MHz + 120 HZ Diode, 1N914 LED LED Standoff Inductor Radial Variable, .85-1.2uH 12.5 Turn Inductor Axial, 2uH Inductor Axial, 2.7uH Inductor Axial, 22uH Ferrite Bead Jack, Phono, RF Output, PC Mounted Socket, I.C., 16 Pin

Socket, I.C., 40 Pin Socket, I.C., 24 Pin Socket, I.C., 14 Pin Transistor, 2N3906 Transistor, 2N3904 Transistor, 2N3563 Transistor Power PNP, MJE 210 PCB PART NUMBER

CA021 375

14-5471

14-5182 14-5220 14-5391 C018974-01 C019874-03 14-5681 C018974-02 14-5101 C018081 018013 015510 31-1N914 CO14776 C018143 010823

010822 C017224 014380 [014384 79-5903 C014386-03

C014386-09 C014386-07 C014386-02 33-2N3906 34-2N3904 34-2N3563 018094 021376

Page 168

LOCATION

CX5200 Field Service Manual DESCRIPTION

TOP HOUSING ASSY (ORIGINAL AND UNIVERSAL 4-PORT) Housing Top Button (Power ON/OFF) ATARI Logo Name Plate Spring (Power ON/OFF) Connector Cover

TOP HOUSING ASSY(2-PORT) Connector Cover Top Housing Name Plate Button Spring

BASE ASSY (ORIGINAL AND UNIVERSAL 4-PORT) Rubber Feet Housing Bottom Cartridge Door Rear Housing Cord Wrap Cover Controller

BASE ASSY(2-PORT) PART NUMBER

CA018175-01

CO18131 C018137 Colsl4al CO18144 CO018951

CA021587-01 021353 CA021 362 CO18l4l 018137 CO18144

CA018176-01

88-1006 C018132 C018139 C018218 C018952

CA021588-XX Bottom Housing C018132 Rubber Feet 88-1006 Rear Cartridge Door C018139 Label, FCC 019107

ATARI VCS CX5200 CAO18174-01 ATARI CX52 CONTROLLER ASSY CAO18107 (ALL MODELS)

Top Housing CO18108 Bottom Housing C018109 Top Bezel CO18110 Side Bezel CO18111 Top Actuator Plate CO18112 Bottom Actuator Plate CO18113 Slide Block CO18114 Boot CO138115 Retaining Ring CO18116 Pivot Shaft 018120 Knob 018121 Support Plate (Keyboard) 018123 Flex Circuit CO18124 12 Key Switch Set 018126 2 Fire Button Switch Set 020501 Auxiliary Function Keys C018128

8-11 Changed by ECN #0036 6/21/83

Page 169

LOCATION

cl

C3,4 C5,6,7,8 c9 Clo RI-4 R5,6 R7,26-29 R8 R9-12 R13-16 R17,19 R18-20 R21,22 R23,24

CX5200 Field Service Manual DESCRIPTION

Controller Cable Assy Top Housing Assy Pot & Arm Assy Cable Pot Assy

TRAKBALL ASSY (CX53) (ALL MODELS) Top Housing Assy Bottom Housing Assy Lower PCB Assy Roller Shaft Assy Cable Assy

Top Housing Assy Top Housing Name Plate 12-Key Switch Set Fire Button Auxiliary Function Keys Upper PCB Assy Spring

Bottom Housing Assy Bottom Housing Roller Shaft Assy Idler Shaft Assy Ball, 2 1/4" Diameter Feet, rubber Lower PCB Sub-Assy Shaft, Roller Encoding Wheel Bearing

Lower PCB Assy Cap, Electrolytic Radial 10uf 16V Cap, Ceramic Axial .luf 50V Cap, Ceramic Axial 470pf 50V Cap, Mylar Radial: .luf, 100V Cap, Ceramic Axial: .Oluf 50V Cap, Ceramic Axial: .22uf 50V Resistor: 3K 1/4W Resistor: 12K, 1/4W Resistor: 10K 1/4W i 21K 1/4W

Resistor: 180K 1/4W Resistor: 240 Ohm 1/4W PART NO.

CAO018145 CA018223 CA018987 CA018988

CA020194

CA020197 CA020198 CA020140 CA0205383 CA020338

CA020197 020195 020193 C018126 020192 C018128 CA020287 012951

CA020198 021096 CA0205383 CA020582 020191 88-1006 CA020141 020572 020571 020190

CA020140 C014392 C014180-19 C014180-07 017885 CO14180-18 C014181-05 14-5302 14-5123 14-5471 14-5102 14-5222 14-5132 14-5433 14-5303 14-5184 14-5241

Page 170

SECTION 9

SERVICE BULLETINS

This section is to be used by you to file the three classifications of service bulletins that are periodically released by the Director of Technical Support.

The following are brief descriptions of each classification:

FIELD CHANGE ORDER

A Field Change Order describes mandatory hardware or software changes to ATARI Computer products and instructs how to implement these changes. The changes must be performed on all units serviced or repaired.

UPGRADE BULLETIN

An Upgrade Bulletin describes product improvements or modifications that the consumer may wish to purchase. These bulletins allow you to modify the customer's unit to add capabilities which may not have been available when the unit was originally manufactured.

TECH TIP

A Tech Tip is a document of a general nature which transmits routine service or repair information. By communicating methods developed since you attended training classes, Tech Tips aid to continuously improve repair skills and increase knowledge of ATARI Computer Products.

Other times, Tech Tips alert you to units that have been modified and are now standard for ATARI Manufacturing, but are different from many existing units and require different repair techniques.

CX5200 Field Service Manual 9-1

Page 171

Consumer Product Service

Manager of Tehnica!l Support

ATARI TECH TIP number 6

mopeL, ATARI CX5200 pate: 11/17/32

SUBJECT:

CX5200 Power Adaptor

DESCRIPTION:

Do not use an HCD Power Adaptor with the CX5200 as it will damage both the HCD Power Adaptor and the CX5200 Switchbox.

The proper Power Adaptor to use with the CX5200 is:

CX521 AC/DC Power Adaptor, Part Number C018187

Output: 9.3 volts DC at 1.95 A.

TROUBLESHOOTING AND MAINTENANCE:

N/A

TESTING PROCEDURES:

N/A

ENCLOSURES:

N/A

(Qh mee ces Come 16292 ez)

Page 172

i Consumer Product Service

is Manager of Tehnical Support VCS

ATARI TECH TIP number_[ MODEL: Cx 5299 DATE: 1/20/83

SUBJECT:

Defective Rockwell 6502 MPU on CX5200 PC Board.

DESCRIPTION:

Rockwell MPUs with date code of 8250 and later (stamped with the letters RC) have a timing defect.

A factory modification adds an R-C network on the component side of the CX5200 PC Board at IC U14A (pin 1) and U6A (pin 4) (see Figures 1 and 2).

Note: You do not need to remove this network to use any other manufacturer's MPU or a Rockweil MPU with a different date code.

£7 eo

Figure 1. CX5200 Schematic (R-C Network)

Component Side CX5200 PC Board

Figure 2. Factory Modification o. 16291 (3/82)

Page 173

aN Consumer Product Service

er Manager of Tehnicai Support VCS

AIAG TECH TIP number _/CONT._ | MODEL: cx5200 DATE: 1/29/93 i

If you are installing an RC stamped 6502 on a CX5200 PC Board which has not had the factory modification added to the component side:

Add an R-C network to the soider side of the PC Board (See Figure 3).

Solder Side \CX5200 PC Board

Figure 3. R-C Network (Add to solder side of CX 5200 PC Board)

PROCEDURES:

You will need:

° 1 - 100 pf capacitor (P/N C014130-03) e 1 - 470.6% resistor (P/N 14-5471) e Sleeving (approximately 2" in length)

Oc ce coe 1191 (3/82)

Page 174

Consumer Product Service

is, Manager of Tehnical Support VCS

Alen TECH TIP number ZCONT_ MODEE: _cx5200 DATE: 1/20/23

See Figure 3 for the following steps:

us Straighten the lead of C27 (solder side) and solder one lead of the 100 pf capacitor to it.

  • Point A is an unoccupied well between IC's UL4 and U17. It is connected directly to Pin | of U14. Cut the trace running between points A and B as close to Point A as possible. Use a OVM to insure that the trace is now open.
  • Add sleeving to one lead of the 470.6% resistor. Insert the lead into the well at Point A and solder.

4, Wrap the remaining lead of the 100 pf capacitor around the lead of the 470.£% resistor at Point A and solder.

BH Remove the solder from well at Point B which is directly beneath U6. Add sleeving to the remaining lead of the 470 £2 resistor. Insert this lead into the hole at Point B and solder.

TESTING PROCEDURES

Use standard testing procedures as outlined in the CX5200 Field Service Manual (P/N FD100127, Rev. 2).

DIFFICULTY REPORTING

If you have any questions or need further clarification concerning this Tech Tip, contact the ATARI Tech Line Specialist.

Inside California (800) 672-1466

Outside Catifornia (800) 538-1535

eo 162391 (3/82)

Page 175

Consumer Product Service

aus Manager of Tehnicai Support VCS

ities TECH TIP number 8 _ MODEL: — ¢x5200 DATE: 20/33

SUBJECT: CX5200 Controller

DESCRIPTION:

Repair CX5200 Controllers with damaged boots in the following manner:

  • Follow Disassembly instructions for the CX5200 Controller in the CX5200 Field Service Manual.
  • Remove the top controller case and pull off the joystick handle.
  • | Remove the boot retaining ring. Remove and discard the damaged boot.
  • If the top controller case contains the square ridge around the access well, as illustrated in "A" below, remove and discard it. Replace it with the new top controller case in which this square tidge has been removed, as illustrated in "B".

es

  • Insert new boot, retaining ring, and joystick handle. Old Top Controller Case New Top Controller Case
  • Reassemble controller according to the instructions in the CX5290 Field Service Repair Manual.

oe 16193 (3/62)

Page 176

fi Consumer Product Service

's Manager of Tehnical Support VCS

AIARI TECH TIP number SCON™ _ MODEL: cxs2n0 DATE: yon/e3 |

SUBJECT: CX5200 Controller

DIFFICULTY REPORTING:

Tf you need further clarification concerning this “Tech Tip, call the ATARI

Techline Specialist:

Inside Catifornia (800) 672-1466

Outside California (800) 538-1535

ENCLOSURES: 20 modified top controller cases

a sexsi cavazy

Page 177

Consumer Product Service TT

, ‘ Manager of Technical Support ves ATARI TECH TIP number __0Q__ i MODEL: 5200 DATE: April 8, 1983

SUBJECT:

s 5200 Controller Knob Puller Tool

PROBLEM AND SOLUTION:

It has been learned that removal of the 5200 Controller Knob is difficult.

To assist you with this task, a 5200 Controller Knob Puller Tool (FC100214) is now available from our Sales Order Department.

USE AND METHODOLOGY:

This tool is used to easily remove the controller knob without damaging the controller. .

Push the knob shaft into one of the corners of the top housing opening. Push down the boot with the tool to expose the shaft. Push the too! toward the shaft until the shaft is inside the notch of the tool's head (See Figure 1). Now, gently lever the tool, and the knob will pop off.

NOTE: By using care, you will not damage the boot during this process.

! VF Figure 1. Controller Knob Removal.

PROBLEM REPORTING:

If you require further information or assistance concerning this Tech Tip, contact the Atari Tech-Line Specialists.

Inside California (300) 672-1466

Outside California —= (800) 538-1535

10291 (3/82)

Page 178

Consumer Product Service

Manager of: Technical Support

ATARI TECH TIP —

MODEL: 5200 DATE: April 8, 1983

SUBJECT: ; New Fire Button (C020501)

PROBLEM:

The fire button on current 5200 controllers have been accused of being "mushy and slow to respond”.

SOLUTION:

Atari has designed a fire button which is not mushy and reacts rapidly. This new fire button will replace the old models. When ordering fire buttons use part number C020501.

TESTING AND TROUBLESHOOTING:

There is no change to either maintenance or trouble shooting techniques because of this change.

PROBLEM REPORTING:

If you have questions or require further explanation concerning this Tech Tip, contact your Atari Tech-line Specialists:

Inside California (800) 672-1466

Outside California (800) 538-2535

(> vere: commence Conan 1c1ga (3/82)

Page 179

Consumer Product Service

Manager of Techrica Support

ATARI’ TECH TIP number

TT vcs

MODEL: DATE:

SUBJECT:

Capacitor at C241

DESCRIPTION

The capacitor at C241 may be of the incorrect rating. An easy way to identify a problem capacitor is to look at the screen with the diagnostic cartridge on the COLOR BARS. The screen is grainy with faint vertical bars. (The COLOR BARS look like color squares.)

SOLUTION:

Install part number 21-101224M at C241.

PARTS:

PART NUMBER DESCRIPTION

21-L0L224M -22uf Axial Lead Polycap - 1 00v.

INSTALLATION PROCEDURE:

Desolder and remove capacitor at C241, and insert and solder 21-101224M into its place.

TESTING PROCEDURES:

Use standard testing procedures as outlined in the 2600/2600A Field Service Manual (FD1001 33).

PROBLEM REPORTING:

If you have questions or require further explanation concerning this Field Change Order, contact your Atari Tech-line Specialist:

Inside California (800) 672-1466

Outside California (800)538-2535 2600A ATARI Video Computer System April 8, 1933

vere commmcmen commen 1¢193 (3/82)

Page 180

ATARI’ Consumer Product Service |

Manager of Tectrical Surport vcs

TECH TIP number 12

MODEL: 5200 | DATE: June 6, 1983

SUBJECT:

Printed Circuit Board (CA018087)

PROBLEM AND SOLUTION:

)

2)

3)

4) Some 5200 units display a blank dark screen or a screen with garbled information. The probable cause for either of these symptoms is an intermittent solder short (bridge) on the PCB between the AO Address line trace and the feedthru pad of the REF Line trace (near connector J1).

TROUBLESHOOTING:

The problem has been seen to occur during one of the following three instances:

  • When the system is powered-up - the screen is usually blank and dark.
  • =‘ After the system is powered with a cartridge in place - the screen will display random garbled data. _
  • Either of the above can be seen when the PCB is moved or slightly flexed near connector Jl.

SOLUTION:

To remedy the problem, perform the following five procedures in the exact order given:

Turn off power, and disconnect AC and interconnect cables.

Disassemble unit to expose the component side of the PCB (CAQ18087).

Locate_connectpr Jl, the adjacent AO Address trace and the feed-thru pad of the REF Trace (See Figure |).

Carefully remove the excess solder from the pad and wipe the area Clean. Inspect the pad and if necessary use an X-acto imife to cut a shallow groove between the AO Address Line and the feedthru pad. Se very carefuly not to nick or cut the trace adjacent to the pad.

Reassembie and test the unit.

16291 (3/az)

Page 181

ji Consumer Product Service Manager of Tectraal Surport j : vcs

ATARI TECH TIP number 1 z

CxX5200 DATE: MODEL:

& - ——=

Remove excess solder between trace & feedthru pad here.

A@ Address Line Trace “REF Trace

Figure 1. 5200 PCB Solder Side at J1

DIFFICULTY REPORTING:

If you need further clarification concerning this Tech Tip, call the Atari Tech-Line Specialise

Inside California (800) 672-1466

Outside California (800) 538-1535

Com Common, 26191 (3/82)