Raiden (Fabtek)
Raiden (World set 1) (Seibu Kaihatsu, 1990) · Manual · 16 pages · 10 sections · original scan
RAIDEN — OWNERS MANUAL
VIDEO GAME OPERATOR:
Don’t Get Involved In A Federal Crime. Don’t Buy Or Operate Copy Or Unauthorized Boards In Your Games.
Every operator who buys or operates a counterfeit or unauthorized {imported or domestic) is contributing to the end of our industry and committing a FEDERAL CRIME. New criminal laws have recently been enacted that provide for maximum penalties of $250,000 or five years in prison or both, per offense. EACH GAME IS A SEPARATE OFFENSE.
If you have any information about any unauthorized games in the United States, contact your local FBI or,
American Amusement Machine Association
205 ue Strand Suite 3
Alexandria, Virginia 22314
(703) 548-8044 All information will be treated in confidence. )
SAFETY
The following topics should be carefully studied to insure maximum reliability and safety for both serviceman and customer. Shock Hazard: The high voltage present on the monitor may be very dangerous. Extreme caution must be used when working with or around the monitors. Be certain that the grounding strap is attached to the monitor frame. The picture tube in the monitor is also a hazard and should be handled with care. Do not strike, scratch, or subject the tube to more than moderate pressure as it may implode causing serious injury from flying glass. Be certain that the control panel, power supply monitor, and coin door are all properly grounded to the ground wire inside the line cord. Do not remove ground prong off plug end.
PARTS LIST
1 - Plex Marquee 1 - Control Panel Overlay 1 - FCC Cage 1 - Graphic Sheet 2 - Side Graphics 1 - Manual 6 - Buttons 1 - JAMMA Cable 1 - Marquee Art 1 - RAIDEN PCB 2-8 Way Joysticks & Hardware
FABTEK® 8335 154th Avenue NE Redmond, WA 98052 (206) 882-1093
FOR SERVICE CONTACT:
Your authorized Fabtek® Distributor or SUMMIT SERVICE 2274 University Avenue St. Paul, MN 55114 (612) 645-9077
SYNC
GROUND
RAIDENG® is protected by federal copyright laws and is the property of Fabtek®. Any unauthorized versions of this game are illegal by federal law. AAMA protected stickers must be * attached to the PCB. Please notify Fabtek of any boards not having the AAMA seal.
VIDEO GREEN
VIDEO BLUE
P NEG COMP. VIDEO GROUND COUNTER #2 COUNTER #1 VIDEO RED 16 COIN INPUT #1 COIN INPUT #2
T 27,28.,¢e,f 1,2,A.B8 on nN
THIS EQUIPMENT GENERATES AND CAN RADIATE RADIO FREQUENCY ENERGY; IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, IT MAY CAUSE INTERFERENCE WITH RADIO COMMUNICATIONS. AS TEMPORARILY PERMITTED BY REGULATION, IT HAS NOT BEEN TESTED FOR COMPLIANCE PURSUANT TO SUBPART J OF PART IS OF FCC RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST SUCH INTERFERENCE. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE INTERFERENCE IN WHICH CASE THE USER, AT HIS OWN EXPENSE, WILL BE REQUIRED TO TAKE WHATEVER MEASURES NECESSARY TO CORRECT THE INTERFERENCE. COIN SHITCHES
An isolation transformer must be used with the monitor and power supply. 8 OHM SPEAKER
This game must be equipped with a three wire 110 volt plug for safety. Under no circumstance remove the ground plug. g z = e H e a | UH
This game is designed with a JAMMA 56 pin connector. This plug is one of the finest operator friendly features in our industry today. What this means to you is that: 110 vac
BULSS
- 1, 2, A, B, 27, 28, e and f are grounded
- 3.4. Cand D are +5 volts
- 5 and E are -5 volts
- 6and F are +12 volts LIGHTS #44 ISOLATION TRAMSFORMER COIN DOOR
Also, all video and joystick functions are always in the same place. Once a cabinet is wired for JAMMA, it is easily changed from game to game. EMI FILTER RGB COLOR MONITOR HORIZONTAL
Many older games such as Pac Man®, etc., have the power supply on the board. This will not work!!! Only a JAMMA connector with proper voltage will work. Fabtek recommends using an !1 amp switching power supply with RAIDEN. VARISTOR ON/OFF SWITCH MONITORS
RAIDEN is designed to be operated with a vertical raster scan monitor with negative sync (RGB). This means RAIDEN will not work with any X-Y (Tempest, Space Dual, Star Trec), etc. An isolation transformer must be used in conjunction with the monitor. This is for your safety. The monitor also utilizes “ extremely high voltages. The monitor may also retain a charge for and extended period of time. Safety goggles must be worn while removing or replacing the monitor. ‘wa wo OFCEE 1ST PLAYER CONTROLS
FUSE 3 AMP SLO-BLO
It is highly recommended that the monitor is verified good before the new RAIDEN Kit is installed in your new and or rebuilt cabinet. i110 vac
Power Up Items
RED SQUARE INCREASES FIREPOWER BLUE SQUARE CHANGES FIREPOWER TO BLUE LASER)
@ ty ne” at % é
TO FIREPOWER ADDS MISSLES ADDS HOMING MISSLES TO FIREPOWER
ADDS NUCLEAR BOMB TO FIREPOWER we,
% INSTALLATION OF KIT IN USED CABINET
To Disassemble:
- Remove marquee glass and monitor glass.
- Remove control panel and set aside.
- Remove old wire harness, leaving 110 volt wiring intact. Also, leave the grounding straps to the monitor, coin door, control panel, and power supply intact.
Installation:
- Mount the board set on the side panel of the cabinet as close to the middle of the game as possible (approximately 10-12” off bottom).
- Mount the power supply on the bottom of the cabinet with connectors facing the rear of the cabinet. An optional mounting might be on the side panel just below the board set, connector to rear. E
- If the game does not have an isolation transformer, you must protect your customers and your game. Install one between the 110 volt line and your monitor/ power supply.
- Place the provided JAMMA wiring harness on the board. Connect the +5, +12, -5, and ground wires to the corresponding lugs on the power supply, connecting all the wires. If you don’t, you will probably burn the board connector.
- Runa wire from -5 volts to the coin door lights. Run a wire from +12 volts to the coin counters. This completes the power requirements.
- Connect the Audio (+) and Audio (-) to the speaker.
- Connect the video red, green, blue, ground, and sync to the corresponding wires on the monitor. If the monitor is not a negative composite sync, see sync modifications chart.
- Cut the marquee to size. Replace the marquee lamp, if needed. Install the marquee panel.
- Connect the coin 1 and coin 2 wires to the coin switches. Connect the coin counter | and coin Open back door and remove old board set and power supply, if you are using a new switching power supply.
counter 2 wires to the coin counters.
10.
ll.
12.
13.
Disassemble the control panel of all the hardware. Do not remove the old panel overlay. Determine where to place the new joystick and buttons if they must be repositioned. Then, cut new holes.
Cut and drill plex as needed. Remove the old control panel overlay carefully and apply the new overlay on top of the old glue. Use an Exacto knife to cut out any button or bolt holes. Apply necessary decals over appropriate buttons. Now assemble the control panel.
Bolt the control panel to the cabinet. Now connect the appropriate wires to the correct switches. Connect the 1 player and 2 player start wires.
Be sure to install the FCC cage to avoid unnecessary radio frequency interference.
Power up the game. Look over your installation for errors, and then apply power, listening for unusual sounds. Check for smoke or sparks. If everything is okay, wire tie all wires to form a nice, neat wiring harness. Clean the cabinet inside and out. Measure the +5 volts on the furthest point from the edge connector and adjust 5 volts to 5.05 volts. Use a tinted plex over the monitor if there are burns in the screen. We suggest bronze or grey tinted plex. Touch up the cabinet with fresh paint, and then repair all cabinet dents or chips, using an auto body product called Duraglass. This is similar to bondo. You can consult your local auto body shop or auto parts supplier for this product, as well as advice on how to use it.
RAIDEN
Fabtek recommends installing your new RAIDEN Kit in only a new or refurbished cabinet. Installing RAIDEN in an older cabinet will result in lower earnings. The cabinet should be as follows:
- vertical monitor
- 11 amp or larger power supply
- monitor not laying down flat.
BOMB START BOMB
NN ee e° £ e°
/ SHOOT SHOOT 8-WAY JOYSTICK 8-WAY JOYSTICK RAIDEN — VERTICAL SCREEN — 2 X 8 WAY JOYSTICK 2 BUTTONS DIP-1 SWITCH FUNCTION
COIN MODE SELECT
1 COIN 1 PLAY (OFF) | OFF | OFF | OFF | OFF ‘ 2 COINS 1 PLAY ON _| oFF | OFF | OFF 3 COINS 1 PLAY OFF | ON _| OFF | OFF 4 COINS 1 PLAY ON | ON _| OFF | OFF 5 COINS 1 PLAY OFF | OFF | ON | OFF 6 COINS 1 PLAY ON [orf | oN | OFF 1 COIN 2 PLAY OFF | ON | ON | OFF MODE 14 1 COIN 3 PLAY ON | ON | ON | OFF 1 COIN 4 PLAY OFF | OFF | OFF | ON 1 COIN 5 PLAY ON | OFF | OFF | ON 1 COIN 6 PLAY OFF | ON | OFF | ON 2 COINS 3 PLAY ON | ON | OFF | ON 3 COINS 2 PLAY OFF | OFF | ON | ON 5 COINS 3 PLAY ON | OFF | ON | ON 8 COINS 3 PLAY OFF | ON | ON | ON FREE PLAY COIN 1. COIN 1 PLAY
UNUSED.
| MECH. | 2 COINS 1 PLAY | ON _| OFF |
| a) | 3 COINS 1 PLAY | OFF | ON |
MODE 2 5 COINS 1 PLAY ON | ON
| COIN | 1 COIN 2 PLAY | OFF | |
| MECH. | 1 COIN 3 PLAY | ON | |
| (8) | 1 COIN 5 PLAY | if | OFF |
_| coin “6 PLAY | (ON) ON **STARTING COIN NORMAL x2
SCREEN INVERT NORMAL INVERT. DEFAULT SETTING
DIP-2 OFF
OFF
FUNCTION SWITCH
HARD COUNTS ON_| OFF. Vj=|o OFF | ON
ON_| OFF OFF | ON EXTEND PLAYER 150000/400000 80000/300000 Ast/2nd 300000/1000000 1000000/5000000. NORMAL OFF | OFF DIFFICULTY EASY. i HARD OFF | ON VERY HARD. on _| ON. CONTINUE PLAY YES OFF. NO ON DEMO SOUND YES. : OFF | NO ON.
| DEFAULT SETTING | oF | [ort | ofr | [ore | [orr | [orr | [orr | oFF |
Telex: 297249 CONTROLS UR RAIDEN JAMMA EDGE CONNECTOR/CABLE
‘COMPONENT SIDE SOLDER SIDE
FUNCTION COLOR a COLOR FUNCTION
GROUND BLK BLK GROUND
GROUND BLK BLK GROUND
#5 VOLTS RED RED +5 VOLTS:
+5 VOLTS RED RED +5 VOLTS
~§ VOLTS BRN ~5 VOLTS
+12 VOLTS: BLU BLU +12 VOLTS,
<{m}o}a}wlulz
|COIN COUNTER #1 BLU/BRN WHT/PUR, COIN COUNTER #2]
AUDIO POS + WHT/BLK BLK AUDIO NEG -
VIDEO RED RED GRN VIDEO GRN
VIDEO BLU BLU WHT VIDEO SYNC*
VIDEO GND BLK BRN/WHT SERVICE SWITCH
YEL WHT/BRN
COIN INPUT 1 WHT/YEL. GRN/YEL COIN INPUT 2
START 1 PNK/BLK RED/BLK START 2
1PUP ORG/BLU BRN/BLU 2PuUP
1 P DOWN GRN/ORG ORG/WHT 2 P DOWN
1P LEFT GRN/BLU ORG/GRN 2P LEFT KD/DYNAMO — UNIVERSAL VIDEO WIRING 56 PIN EDGE CONN. PIN-OUT CHART (JAMMA COMPATIBLE) COMPONENT SIDE SOLDER SIDE
FUNCTION COLOR POS COLOR FUNCTION
GROUND BLK BLK GROUND
GROUND BLK BLK GROUND
+5 VOLTS RED RED +5 VOLTS
+5 VOLTS RED RED. +5 VOLTS.
-6 VOLTS WHITE WHITE -5 VOLTS:
+12 VOLTS YELLOW YELLOW #12 VOLTS
KEY KEY
{COIN COUNTER #1 BRN ~ eon counreR #2
alo] s| ol ofr] olo
ICOIN LOCK OUT 1 RED ICOIN LOCK OUT 2
SP (+) WHT e WHT/BLK sP()
NG. BLUE-OPTION OP.-BLU/ BLACK N.C.
VIDEO RED RED GRN VIDEO GRN
VIDEO BLU BLU GRAY VIDEO SYNC*
VIDEO GND BLK z RED/BLACK | SERVICE SWITCH
TEST SW. BROWN. ro OP.-BRN/BLACK TILT SW.
COIN SW. 1 WHITE 16 COIN SW, 2
START 1 GRAY 7 WHITE/GRAY START 2
1 PUP VIOLET 18 WHITE/VIOLET 2PUP
1 P DOWN BLUE 19 WHITE/BLUE 2P DOWN
+P LEFT GREEN 20 WHITE/GREEN 2P LEFT
1 P RIGHT RED/YEL WHT/ORG 2P RIGHT 1 P RIGHT YELLOW 21 WHT/YELLOW 2P RIGHT
1 P SHOOT RED/WHT ol x] sa] slzla}a}o;r} as} >| es] x] >]Nn BRN/BLK 2P SHOOT <jm}ofaolwiujxr]s]x<|a}s]2joa}aj)o]/r] a} >] 3] x)>jpNn
a 1 P PUSH 1 ORANGE, 22 WHT/ORANGE 2P PUSH 1
1P BOMB WHT/RED YEL/WHT 2P BOMB 1 P PUSH 2 RED 23 « WHT/RED 2 P PUSH 2
YEL/BLK BRN/GRN 4 P PUSH 3 BROWN 24 b WHT/BROWN 2P PUSH 3
+ NC. BLUE/WHT 25 c GREEN/WHT Nc.
NC. RED/WHT 26 d YELLOW/WHT NC.
GROUND BLK BLK GROUND GROUND BLK 27 e BLK GROUND
GROUND BLK BLK GROUND GROUND BLK-OPTION 28 1 BLK-OPTION GROUND
- Video syne composite negative
106 Garlisch Happ CONTROLS, inc.
Phone: (312) 593-6130 Fax: (312) 593-6137 Elk Grove, Illinois 60007 joystick 96-1405-00 Hub for-leaf switch 96-1402-00 4-way 8-way actuator PARTS LIST: 96-1015-00 Washer 96-1400-00 Chrome shaft & knob 96-1401-00 Hub for microswitch 96-1302-00 Pivot cone 96-1403-00 Blade holder 95-0737-00 Microswitch 96-1409-00 Leafswitch
- Video syne composite negative
96-1015-00.
96-1302.00. long life ¢ Rugged actuator for construction
¢ Spring return to center
- Nylon and solid steel
- Micro or leaf switches ¢ Unique handle design
- Change actuation to individually replaceable
4-way or 8-way simply by flipping actuator over Happ Controis
Feat SUPER JOYSTICK turing
Star Tech Tips We are grateful to Star Tech Journal™ for allowing us to publish excerpts from their journal.
Monitor Sync If your monitor does not have dual polarity positions for sync, you may use on of the following methods to get your game going. CURE 1: Install a simple one I.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new I.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.)
HORIZONTAL SYNC INPUT FROM P.C.B. 5 VDC (OR COMPOSITE SYNC INPUT)
HORIZONTAL SYNC OUTPUT TO MONITOR (OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM P.C.B. 5VDC (PIN 14)
SOLDER TO EXISTING CHIP
VERTICAL SYNC OUTPUT TO MONITOR NOT USED
NEW 741804
FIG. 2
BENT PINS. = vs) GND (PIN 7)
FIG. 1
CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85x14 OB.
Cut the traces on the solder side of the board between input pins 5 & 6 to the unbanded (anode) ends of diodes X201 & X202. Add MPSA 56 transistor as follows: Collector to anode leads of diodes X201 & X202. Base pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode ZD201. Insert a 1N4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3)
RED1 GREEN 2
BLUE 3 GND 4 FIG. 3 VERT. 5 HORIZ. 6 MPSAS6 0000
. X202 Cur TRACES =f
X207 gs
- Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”. CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial lead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the C303 location. CURE 2: Connect 1N4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.
IN4148
NEG: SYNC INPUT
FIG. 4 “GND BLUE GREEN RED _ an ae | “OW O_O _O_ O} 6 5 7 4 3 2 1
IN4148
CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from - W102 to either }2 or ]3.
CURE 3: For Wells-Gardner K4600 series monitors. Replace C356 (4 7uf 25V) on the Horizontal/vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune | with the horizontal width pot.
STAR TECH JOURNAL P.O. Box 1065 18 N. Centre Street Merchantville, J.J. 08109 609-662-1080
COIN COUNTER DIAGRAM
If only one coin counter is to be used install two diodes in the following manner:
ANao01 COIN COUNTER 1
COIN COUNTER COIN COUNTER 2
Star Tech Tips We are grateful to Star Tech Journal™ for allowing us to publish excerpts from their journal.
Monitor Sync If your monitor does not have dual polarity positions for sync, you may use on of the following methods to get your game going. CURE 1: Install a simple one I.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new I.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.)
HORIZONTAL SYNC INPUT FROM P.C.B. 5 VDC (OR COMPOSITE SYNC INPUT)
HORIZONTAL SYNC OUTPUT TO MONITOR (OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM P.C.B. 5VDC (PIN 14)
SOLDER TO EXISTING CHIP
VERTICAL SYNC OUTPUT TO MONITOR NOT USED
NEW 741804
FIG. 2
BENT PINS. = vs) GND (PIN 7)
FIG. 1
CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85x14 OB.
Cut the traces on the solder side of the board between input pins 5 & 6 to the unbanded (anode) ends of diodes X201 & X202. Add MPSA 56 transistor as follows: Collector to anode leads of diodes X201 & X202. Base pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode ZD201. Insert a 1N4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3)
RED1 GREEN 2
BLUE 3 GND 4 FIG. 3 VERT. 5 HORIZ. 6 MPSAS6 0000
. X202 Cur TRACES =f
X207 gs
- Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”. CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial lead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the C303 location. CURE 2: Connect 1N4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.
IN4148
NEG: SYNC INPUT
FIG. 4 “GND BLUE GREEN RED _ an ae | “OW O_O _O_ O} 6 5 7 4 3 2 1
IN4148
CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from - W102 to either }2 or ]3.
CURE 3: For Wells-Gardner K4600 series monitors. Replace C356 (4 7uf 25V) on the Horizontal/vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune | with the horizontal width pot.
STAR TECH JOURNAL P.O. Box 1065 18 N. Centre Street Merchantville, J.J. 08109 609-662-1080
COIN COUNTER DIAGRAM
If only one coin counter is to be used install two diodes in the following manner:
ANao01 COIN COUNTER 1
COIN COUNTER COIN COUNTER 2
Telex: 297249 CONTROLS UR RAIDEN JAMMA EDGE CONNECTOR/CABLE
‘COMPONENT SIDE SOLDER SIDE
FUNCTION COLOR a COLOR FUNCTION
GROUND BLK BLK GROUND
GROUND BLK BLK GROUND
#5 VOLTS RED RED +5 VOLTS:
+5 VOLTS RED RED +5 VOLTS
~§ VOLTS BRN ~5 VOLTS
+12 VOLTS: BLU BLU +12 VOLTS,
<{m}o}a}wlulz
|COIN COUNTER #1 BLU/BRN WHT/PUR, COIN COUNTER #2]
AUDIO POS + WHT/BLK BLK AUDIO NEG -
VIDEO RED RED GRN VIDEO GRN
VIDEO BLU BLU WHT VIDEO SYNC*
VIDEO GND BLK BRN/WHT SERVICE SWITCH
YEL WHT/BRN
COIN INPUT 1 WHT/YEL. GRN/YEL COIN INPUT 2
START 1 PNK/BLK RED/BLK START 2
1PUP ORG/BLU BRN/BLU 2PuUP
1 P DOWN GRN/ORG ORG/WHT 2 P DOWN
1P LEFT GRN/BLU ORG/GRN 2P LEFT KD/DYNAMO — UNIVERSAL VIDEO WIRING 56 PIN EDGE CONN. PIN-OUT CHART (JAMMA COMPATIBLE) COMPONENT SIDE SOLDER SIDE
FUNCTION COLOR POS COLOR FUNCTION
GROUND BLK BLK GROUND
GROUND BLK BLK GROUND
+5 VOLTS RED RED +5 VOLTS
+5 VOLTS RED RED. +5 VOLTS.
-6 VOLTS WHITE WHITE -5 VOLTS:
+12 VOLTS YELLOW YELLOW #12 VOLTS
KEY KEY
{COIN COUNTER #1 BRN ~ eon counreR #2
alo] s| ol ofr] olo
ICOIN LOCK OUT 1 RED ICOIN LOCK OUT 2
SP (+) WHT e WHT/BLK sP()
NG. BLUE-OPTION OP.-BLU/ BLACK N.C.
VIDEO RED RED GRN VIDEO GRN
VIDEO BLU BLU GRAY VIDEO SYNC*
VIDEO GND BLK z RED/BLACK | SERVICE SWITCH
TEST SW. BROWN. ro OP.-BRN/BLACK TILT SW.
COIN SW. 1 WHITE 16 COIN SW, 2
START 1 GRAY 7 WHITE/GRAY START 2
1 PUP VIOLET 18 WHITE/VIOLET 2PUP
1 P DOWN BLUE 19 WHITE/BLUE 2P DOWN
+P LEFT GREEN 20 WHITE/GREEN 2P LEFT
1 P RIGHT RED/YEL WHT/ORG 2P RIGHT 1 P RIGHT YELLOW 21 WHT/YELLOW 2P RIGHT
1 P SHOOT RED/WHT ol x] sa] slzla}a}o;r} as} >| es] x] >]Nn BRN/BLK 2P SHOOT <jm}ofaolwiujxr]s]x<|a}s]2joa}aj)o]/r] a} >] 3] x)>jpNn
a 1 P PUSH 1 ORANGE, 22 WHT/ORANGE 2P PUSH 1
1P BOMB WHT/RED YEL/WHT 2P BOMB 1 P PUSH 2 RED 23 « WHT/RED 2 P PUSH 2
YEL/BLK BRN/GRN 4 P PUSH 3 BROWN 24 b WHT/BROWN 2P PUSH 3
+ NC. BLUE/WHT 25 c GREEN/WHT Nc.
NC. RED/WHT 26 d YELLOW/WHT NC.
GROUND BLK BLK GROUND GROUND BLK 27 e BLK GROUND
GROUND BLK BLK GROUND GROUND BLK-OPTION 28 1 BLK-OPTION GROUND
- Video syne composite negative
106 Garlisch Happ CONTROLS, inc.
Phone: (312) 593-6130 Fax: (312) 593-6137 Elk Grove, Illinois 60007 joystick 96-1405-00 Hub for-leaf switch 96-1402-00 4-way 8-way actuator PARTS LIST: 96-1015-00 Washer 96-1400-00 Chrome shaft & knob 96-1401-00 Hub for microswitch 96-1302-00 Pivot cone 96-1403-00 Blade holder 95-0737-00 Microswitch 96-1409-00 Leafswitch
- Video syne composite negative
96-1015-00.
96-1302.00. long life ¢ Rugged actuator for construction
¢ Spring return to center
- Nylon and solid steel
- Micro or leaf switches ¢ Unique handle design
- Change actuation to individually replaceable
4-way or 8-way simply by flipping actuator over Happ Controis
Feat SUPER JOYSTICK turing
10.
ll.
12.
13.
Disassemble the control panel of all the hardware. Do not remove the old panel overlay. Determine where to place the new joystick and buttons if they must be repositioned. Then, cut new holes.
Cut and drill plex as needed. Remove the old control panel overlay carefully and apply the new overlay on top of the old glue. Use an Exacto knife to cut out any button or bolt holes. Apply necessary decals over appropriate buttons. Now assemble the control panel.
Bolt the control panel to the cabinet. Now connect the appropriate wires to the correct switches. Connect the 1 player and 2 player start wires.
Be sure to install the FCC cage to avoid unnecessary radio frequency interference.
Power up the game. Look over your installation for errors, and then apply power, listening for unusual sounds. Check for smoke or sparks. If everything is okay, wire tie all wires to form a nice, neat wiring harness. Clean the cabinet inside and out. Measure the +5 volts on the furthest point from the edge connector and adjust 5 volts to 5.05 volts. Use a tinted plex over the monitor if there are burns in the screen. We suggest bronze or grey tinted plex. Touch up the cabinet with fresh paint, and then repair all cabinet dents or chips, using an auto body product called Duraglass. This is similar to bondo. You can consult your local auto body shop or auto parts supplier for this product, as well as advice on how to use it.
RAIDEN
Fabtek recommends installing your new RAIDEN Kit in only a new or refurbished cabinet. Installing RAIDEN in an older cabinet will result in lower earnings. The cabinet should be as follows:
- vertical monitor
- 11 amp or larger power supply
- monitor not laying down flat.
BOMB START BOMB
NN ee e° £ e°
/ SHOOT SHOOT 8-WAY JOYSTICK 8-WAY JOYSTICK RAIDEN — VERTICAL SCREEN — 2 X 8 WAY JOYSTICK 2 BUTTONS DIP-1 SWITCH FUNCTION
COIN MODE SELECT
1 COIN 1 PLAY (OFF) | OFF | OFF | OFF | OFF ‘ 2 COINS 1 PLAY ON _| oFF | OFF | OFF 3 COINS 1 PLAY OFF | ON _| OFF | OFF 4 COINS 1 PLAY ON | ON _| OFF | OFF 5 COINS 1 PLAY OFF | OFF | ON | OFF 6 COINS 1 PLAY ON [orf | oN | OFF 1 COIN 2 PLAY OFF | ON | ON | OFF MODE 14 1 COIN 3 PLAY ON | ON | ON | OFF 1 COIN 4 PLAY OFF | OFF | OFF | ON 1 COIN 5 PLAY ON | OFF | OFF | ON 1 COIN 6 PLAY OFF | ON | OFF | ON 2 COINS 3 PLAY ON | ON | OFF | ON 3 COINS 2 PLAY OFF | OFF | ON | ON 5 COINS 3 PLAY ON | OFF | ON | ON 8 COINS 3 PLAY OFF | ON | ON | ON FREE PLAY COIN 1. COIN 1 PLAY
UNUSED.
| MECH. | 2 COINS 1 PLAY | ON _| OFF |
| a) | 3 COINS 1 PLAY | OFF | ON |
MODE 2 5 COINS 1 PLAY ON | ON
| COIN | 1 COIN 2 PLAY | OFF | |
| MECH. | 1 COIN 3 PLAY | ON | |
| (8) | 1 COIN 5 PLAY | if | OFF |
_| coin “6 PLAY | (ON) ON **STARTING COIN NORMAL x2
SCREEN INVERT NORMAL INVERT. DEFAULT SETTING
DIP-2 OFF
OFF
FUNCTION SWITCH
HARD COUNTS ON_| OFF. Vj=|o OFF | ON
ON_| OFF OFF | ON EXTEND PLAYER 150000/400000 80000/300000 Ast/2nd 300000/1000000 1000000/5000000. NORMAL OFF | OFF DIFFICULTY EASY. i HARD OFF | ON VERY HARD. on _| ON. CONTINUE PLAY YES OFF. NO ON DEMO SOUND YES. : OFF | NO ON.
| DEFAULT SETTING | oF | [ort | ofr | [ore | [orr | [orr | [orr | oFF |
Power Up Items
RED SQUARE INCREASES FIREPOWER BLUE SQUARE CHANGES FIREPOWER TO BLUE LASER)
@ ty ne” at % é
TO FIREPOWER ADDS MISSLES ADDS HOMING MISSLES TO FIREPOWER
ADDS NUCLEAR BOMB TO FIREPOWER we,
% INSTALLATION OF KIT IN USED CABINET
To Disassemble:
- Remove marquee glass and monitor glass.
- Remove control panel and set aside.
- Remove old wire harness, leaving 110 volt wiring intact. Also, leave the grounding straps to the monitor, coin door, control panel, and power supply intact.
Installation:
- Mount the board set on the side panel of the cabinet as close to the middle of the game as possible (approximately 10-12” off bottom).
- Mount the power supply on the bottom of the cabinet with connectors facing the rear of the cabinet. An optional mounting might be on the side panel just below the board set, connector to rear. E
- If the game does not have an isolation transformer, you must protect your customers and your game. Install one between the 110 volt line and your monitor/ power supply.
- Place the provided JAMMA wiring harness on the board. Connect the +5, +12, -5, and ground wires to the corresponding lugs on the power supply, connecting all the wires. If you don’t, you will probably burn the board connector.
- Runa wire from -5 volts to the coin door lights. Run a wire from +12 volts to the coin counters. This completes the power requirements.
- Connect the Audio (+) and Audio (-) to the speaker.
- Connect the video red, green, blue, ground, and sync to the corresponding wires on the monitor. If the monitor is not a negative composite sync, see sync modifications chart.
- Cut the marquee to size. Replace the marquee lamp, if needed. Install the marquee panel.
- Connect the coin 1 and coin 2 wires to the coin switches. Connect the coin counter | and coin Open back door and remove old board set and power supply, if you are using a new switching power supply.
counter 2 wires to the coin counters.
SYNC
GROUND
RAIDENG® is protected by federal copyright laws and is the property of Fabtek®. Any unauthorized versions of this game are illegal by federal law. AAMA protected stickers must be * attached to the PCB. Please notify Fabtek of any boards not having the AAMA seal.
VIDEO GREEN
VIDEO BLUE
P NEG COMP. VIDEO GROUND COUNTER #2 COUNTER #1 VIDEO RED 16 COIN INPUT #1 COIN INPUT #2
T 27,28.,¢e,f 1,2,A.B8 on nN
THIS EQUIPMENT GENERATES AND CAN RADIATE RADIO FREQUENCY ENERGY; IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, IT MAY CAUSE INTERFERENCE WITH RADIO COMMUNICATIONS. AS TEMPORARILY PERMITTED BY REGULATION, IT HAS NOT BEEN TESTED FOR COMPLIANCE PURSUANT TO SUBPART J OF PART IS OF FCC RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST SUCH INTERFERENCE. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE INTERFERENCE IN WHICH CASE THE USER, AT HIS OWN EXPENSE, WILL BE REQUIRED TO TAKE WHATEVER MEASURES NECESSARY TO CORRECT THE INTERFERENCE. COIN SHITCHES
An isolation transformer must be used with the monitor and power supply. 8 OHM SPEAKER
This game must be equipped with a three wire 110 volt plug for safety. Under no circumstance remove the ground plug. g z = e H e a | UH
This game is designed with a JAMMA 56 pin connector. This plug is one of the finest operator friendly features in our industry today. What this means to you is that: 110 vac
BULSS
- 1, 2, A, B, 27, 28, e and f are grounded
- 3.4. Cand D are +5 volts
- 5 and E are -5 volts
- 6and F are +12 volts LIGHTS #44 ISOLATION TRAMSFORMER COIN DOOR
Also, all video and joystick functions are always in the same place. Once a cabinet is wired for JAMMA, it is easily changed from game to game. EMI FILTER RGB COLOR MONITOR HORIZONTAL
Many older games such as Pac Man®, etc., have the power supply on the board. This will not work!!! Only a JAMMA connector with proper voltage will work. Fabtek recommends using an !1 amp switching power supply with RAIDEN. VARISTOR ON/OFF SWITCH MONITORS
RAIDEN is designed to be operated with a vertical raster scan monitor with negative sync (RGB). This means RAIDEN will not work with any X-Y (Tempest, Space Dual, Star Trec), etc. An isolation transformer must be used in conjunction with the monitor. This is for your safety. The monitor also utilizes “ extremely high voltages. The monitor may also retain a charge for and extended period of time. Safety goggles must be worn while removing or replacing the monitor. ‘wa wo OFCEE 1ST PLAYER CONTROLS
FUSE 3 AMP SLO-BLO
It is highly recommended that the monitor is verified good before the new RAIDEN Kit is installed in your new and or rebuilt cabinet. i110 vac
SAFETY
The following topics should be carefully studied to insure maximum reliability and safety for both serviceman and customer. Shock Hazard: The high voltage present on the monitor may be very dangerous. Extreme caution must be used when working with or around the monitors. Be certain that the grounding strap is attached to the monitor frame. The picture tube in the monitor is also a hazard and should be handled with care. Do not strike, scratch, or subject the tube to more than moderate pressure as it may implode causing serious injury from flying glass. Be certain that the control panel, power supply monitor, and coin door are all properly grounded to the ground wire inside the line cord. Do not remove ground prong off plug end.
PARTS LIST
1 - Plex Marquee 1 - Control Panel Overlay 1 - FCC Cage 1 - Graphic Sheet 2 - Side Graphics 1 - Manual 6 - Buttons 1 - JAMMA Cable 1 - Marquee Art 1 - RAIDEN PCB 2-8 Way Joysticks & Hardware
FABTEK® 8335 154th Avenue NE Redmond, WA 98052 (206) 882-1093
FOR SERVICE CONTACT:
Your authorized Fabtek® Distributor or SUMMIT SERVICE 2274 University Avenue St. Paul, MN 55114 (612) 645-9077
VIDEO GAME OPERATOR:
Don’t Get Involved In A Federal Crime. Don’t Buy Or Operate Copy Or Unauthorized Boards In Your Games.
Every operator who buys or operates a counterfeit or unauthorized {imported or domestic) is contributing to the end of our industry and committing a FEDERAL CRIME. New criminal laws have recently been enacted that provide for maximum penalties of $250,000 or five years in prison or both, per offense. EACH GAME IS A SEPARATE OFFENSE.
If you have any information about any unauthorized games in the United States, contact your local FBI or,
American Amusement Machine Association
205 ue Strand Suite 3
Alexandria, Virginia 22314
(703) 548-8044 All information will be treated in confidence. )