CATHODE RAY TOMES

Xevious 3D-G

Xevious 3D/G (World, XV32/VER.B) (Namco, 1995) · Manual · 4 pages · 1 sections · original scan

Page 1

Nnamco

X BVO U3 2b --G

OPERATION MANUAL |

/A\ CAUTION In orderto safely use this machine, be sure to carefully read this operation manual and the manual of the cabinetin which this machine to be installed before installation and operation.

This operation manual should be kept together with the machine.

DISTRIBUTED BY: NAMCO LIMITED 2-8-5 TAMAGAWA, OHTA-KU, TOKYO, 146, JAPAN

©1995 NAMCOLTD., ALL RIGHTS RESERVED

Page 2
  • Cautions
  • Be sure to turn off the cabinet whenever installing or removing the PC board. Otherwise you may be hurt by an electric shock.
  • Be sure to use an edge connector which is applied to the JAMMA standard. Any modifications such as cutting the edges of PC boards will cause a failure and also will be out of our guarantee for repair.
  • Never test the PC boards for conductivity with a multimeter or similar device. The PCB contains sensitive chips which could be destroyed even by the internal voltage of such a device.
  • Foreign matters or dust on the PC boards will cause a failure. Tum off the power and clean the PC boards with a brush or similar thing.

(5S) When transporting the PC boards, wrap them with sponges or air caps and pack them in a card board box so that they can avoid a direct impact from outside during shipment.

  • For maintenance, contact your distributor. IP, Start 2P, Start
  • Specifications 2P, Button 1 2P, Button 2
  • Control panel: One-side 2-P specifications 1p, Button 2 + 8-direction lever: 2 (1F,' 2P. °F each) 1P, Button 1 + Button switch: 4 (1P, 2P, 2 each) Button | : (Anti-air Attack) Button 2 : (Anti-ground Attack) + Start switch: 2 (IP, 2P, 1 each)
  • PC board size: 230 x 230 mm a 1P, 8-direction
  • Direction of monitor: Horizontal 2P, 8-direction

Fig. 1 3.Connection

  • Connection of control panel See above to connect JAMMA hamess and extended harness(accessory) to control panel through the cabinet (see P3 : PC board connector table) Connecting expanded hamess to the right speaker allows you to enjoy a stereophonic effect.
  • Connection of PC board Set the PC board in the cabinet and connect JAMMA edge connector and 48P extended edge connector (DDK 225D-10024C2-2312) to the PC board.
  • Explanation of PC Boards 48Pextendededge 56P edge connector connector (JAMMA)
  • Option switches Bi reseed 2 ese! No.1 to "ON" for Test Mode. 12 O No.2 to "ON" for Screen Freeze.

\ Option switch Normally, all of the option switches are "OFF". Speaker volume

  • Speaker volumes To decrease the sound volume of the speaker, turn the speaker volume counter-clockwise.
  • Test Mode Fig.2
  • The PC Board enters the test mode by setting the test switch on the PC Board to "ON" on the game screen. And the test menu screen is displayed on the monitor. Use the test switch (For connection, see P3: PC Board Connector Table) on the cabinet or the option switch on the PC Board. (see P1: 4.(1) Option switches) When an item is selected by operating the 1P control lever up and down and the IP button! switch is pushed, the selected test screen is displayed.
  • Game fees can be changed on the coin option screen, and the game difficulty can be changed on the game option screen. Select an item by operating the 1P control lever up and down, and change its contents using the 1P button! switch (see the option setting table). After that, push the 1P button2 switch to retum to the test menu screen.

ae

Page 3

COIN OPTIONS GAME OPTIONS UARTS TEST POLYGON TEST A.D.S.

  • Switch test screen
  • Sound test screen
  • Coin option screen (Setting of game tees)
  • Game option screen (Setting of game difficulty)
  • Not used
  • Polygon test screen (g)Not used COLOR TEST CONVERGENCE TSTE RS-232C TEST
  • Color test screen (for monitor adjustment)
  • Cross hatch pattern (for monitor adjustment)
  • Not used

(Test menu screen)

CO IN OPTIONS [DEFAULTS IN GREEN } GAME OPT IONS {DEFAULTS IN GREEN ]

GAME COST : (1 or 3) CO IN 1 CRED IT DISCOUNT TO CONT INUE : NO CO IN 1 MECH VALUE : 1 COIN COUNT AS 1 COIN CO IN 2 MECH VALUE: | COIN COUNT AS 1 COIN CO IN 3 MECH VALUE : 1 COIN COUNT AS 1 COIN CO IN 4 MECH VALUE : | COIN COUNT AS | COIN BONUS FOR QUANTITY BUY IN: NONE CRED IT MODE : COMMON COIN COUNTER: TYPE A: | COUNTER: FREE PLAY : NO DIFFICULTY LEVEL : HARD SOLVALOU : 3 MUSIC IN ATTRACT : YES SPEAKER OUT : STEREO Hoary dhyswre

{et er ee) (Game Option Screen) (Coin Option screen)

(Option setting table) Contents ‘one count required for one game (one credit)

  • Game fees
  • DISCOUNT
  • COIN 1 MECH VALUE (10r3)<[1 -9]

50% discount when continuing a play Count per coin i <[(1-9]

4. COIN 2 MECH VALUECount per coin| 1<[1-9]
5.6.Not used|ae
7. BONUS COINOne additional coin per the specified number ofNONE < 2 Coins Give 1 Coin~9 Coins

oiNs Give 3 Coins

  • CREDIT MODE COMMON (Credit is common to 1P and 2P) <, EACH ONE (Credit is set for 1P and 2P each) TYPE A :1COUNTER ( 1Coin counter for 2slots) < 9: COIN COUNTER TYPE B :2COUNTERS ( 1Coin counter for each 1slot)
  • FREE PLAY NO< YES
  • DIFFICULTY LEVEL HARD <[EASY, MEDIUM, HARD, VERY HARD, ULTRA HARD]
  • SOLVALOU <[2,3,4,5] 13.MUSIC IN ATTRACT YES < NO 14.SPEAKER OUT STEREO < MONO

Game fees (Note) Set (D,4@ corresponded to Coin Mech [ &2 in use. 1 COIN 1CREDIT

2 COINS 1CREDIT {COUNT 2COINS |NONE |CREDIT 0/2 Swnee

Page 4
  • PC Board Connector Table

JAMMA edge connector (S6P 3.96 mm pitch) Solder side Terminal No. Parts side a1 GND

GNDB2GND
+5V€3+5V
[EGetares V;D4+5V

E 5

+12Vngens+12V
Insertion errorH| 7[insertion error

preventing reventing (Coin counter 2 J K Sveaker(-) | ~<L | 10 (Speaker)

[Audio (GND)M11|Audio (+)
[Video GREENN12|Video RED

|Video SYNC ervice switch R Ss ‘oin switch 2 F

2P start switchU17IP start swich
2P lever UPVi18|LP lever UP
2P lever DOWNWw19|I1P lever DOWN
2P lever LEFTXx1P lever LEFT
2P lever RIGHT211P lever RIGHT
RP button!zeIP button!
2P button2231P button2
  • Do not connect anything to the blank connectors.
  • Both lockout solenoid and coin counter operate on +12V. + Connect the switches to N.O. terminals such as a microswitch, and the GND to the COM terminal.

N.O. COM... eS 0M, Ne.

  • The supply voltage is available within +5%. For use in the best condition, get the supply voltage as close to the specified voltage as possible.

(Recommended power capacity)

WEE HIVES% Extended edge connector (48P 2.54 mm pitch) Solder side Terminal No. Parts side Speaker R (-) [YEL} Speaker R (+) [ORG | A2 B2 Le. AB BS | T Ad B4

nsertion error AS =5 BS nsertion error

preventing key eventing key A6 B6 oneal A7 B7 a] Bs z

Do not connect anything to the blank connectors.

  • The colors indicated in [] in the extended edge connector table show these of color cords on the extended edge connector hamess in the accessories.

[Connection to stereo cabinet] (L)STEREO / MONO setting Select SPEAKER OUT in the game option screen at the test menu screen. ‘

<Caution>Monophonic cabinets do output only the left-hand sound even if the stereophonic setting is selected.

  • Connection to speakers
  • Connect the (L) speaker to the speaker output of 56P edge connector (JAMMA) on the PC board.
  • Connect the (R) speaker to Speaker R (+), (-) of 48P extended edge connector.
  • Use a DDK 225D-10024C2-2312 as a 48P extended edge connector.