CATHODE RAY TOMES

Fire One

Fire One (Exidy, 1979) · Manual · 32 pages · 10 sections · original scan

Page 1

FIRE ONE

Technical Manual

November 1979

  • EXIDY, Inc.
Page 2

ils

LIke

Iv.

VI. CONTENTS

Installations. .scccecseeseceeeeee 1

Self-testing....

Operator OptionSesssscseseceeeeee 7

Player Control Adjustment.. 10

Replacement Parts List...

SchematicSsecsecevescssecscereees 13

Page 3

LIST OF FIGURES

Figure Number Title

Functions of the 8-position DIP Switch

Player Control Module

aii

Page 4

INSTALLATION:

The Exidy FIRE ONE is a one unit game containing the following:

  • Video monitor module
  • Player control module
  • Mother PC board
  • Daughter PC board
  • Power supply

Before installing the game, open the back door of the unit and check the PC boards and monitor. Also check the wiring harness and make sure all the plugs are connected. To install the game, follow these steps:

  • Determine where to place the game and the direction it should face. Move the game to the location of your choice.
  • Plug the power cord into an electrical outlet. When the game is powered up it should go into the attract mode of operation.
NOTE

To put FIRE ONE into quiet attract mode, locate the 8-position DIP switch on the daughter PC board and set switch 7 to the ON position.

FIRE ONE is now in either the attract mode or quiet attract mode.

Page 5

Il. SELF-TESTING:

FIRE ONE has nine self tests. After FIRE ONE has been shipped and installed, it should be fully tested. To begin the self-testing do the following:

1.

2. Unlock the back door of the unit. Remove the door by lifting it up and out.

Locate the 8-position DIP switch on the daughter PC board. The PC boards are on your right when you are at the back of the unit looking inside. The daughter PC board is on a shelf sticking out from the right side of the cabinet.

Set switch 8 to the ON position.

After the sign-on and copyright message appears on the screen, press the FIRE button to put FIRE ONE in the self-testing mode.

FIRE ONE is now ready for self testing. The FIRE ONE self-testing procedures are as follows

CROSSHATCH FOCUS TEST

  • The first test which appears on the screen is a crosshatch pattern.
  • This pattern tests the color monitor for alignment and convergence.
  • Press the FIRE button to go to the next self test.

COLOR BAR TEST

  • The second test is a color bar pattern. There are eight levels each of red, blue, green and white.

Test and adjust the color monitor against this pattern.

Press the FIRE button to go to the next self test.

Page 6

PLAYER CONTROL TEST

1.

FOR NEXT TEST PRESS BOTH START BUTTONS AT ONCE THEN PRESS FIRE The third test is used to determine whether the player controls are operational and looks like this:

9800 1000 || 0000 9801 0000 |} oo00 = 9802 LEFT Ooll 0000 = - 9802 RIGHT ooll 0000

The last two rows of ones and zeros on the screen change as the player controls are moved. In addition the two green horizontal bars on the far right of the screen also move as the player steering controls are moved.

The row of ones and zeros to the right of the number 9801 tests the ONE PLAYER and TWO PLAYERS control buttons and the coin drop indicator. When the ONE PLAYER button is pressed the last digit changes from a zero to a one, indicating this control button is operational. When the TWO PLAYERS button is pushed the next to the last digit changes from a zero to a one, indicating this control button is oprational. When the third digit from the right changes from a zero to a one it indicates the coin drop is operational.

The row of ones and zeros following "9802 RIGHT" tests the operator controls for the player on the right and "9802 LEFT" tests the operator controls for the player on the left. The first digit of each column changes from a zero to a one when the FIRE button is pressed for each. The second digit changes from zero to one when the DIVE button is pressed for each. All other digits in each row change as the STEERING shafts are moved. Move each STEERING shaft from left to right as you watch the green lines on the far right of the screen move up and down. Line up both green lines with the top, center and bottom lines on the screen. At each position check the row of ones and zeros to be sure they match each other exactly. If the rows match at each position, the STEERING operator controls are in working order.

Page 7

PROGRAM

1.

3.

COLOR (R

l.

MAIN RAM

1. Press both START buttons at once and then the FIRE button to go to the next self test.

MEMORY

The fourth test automatically does a checksum comparison on each program in ROM or PROM.

The screen displays a map of the daughter PC board with good PROMs shown as green bars and bad ones shown as red bars. The locations of PROMs as displayed on the screen map correspond to their location on the daughter PC board when it is in an upright, readable position:

Press the FIRE button to go to the next self test.

AM) MEMORY TEST

The fifth test automatically fills the screen with colorful patterns that do not have meaning. The patterns display for less than a minute while the color memory is tested.

After the color memory is tested the patterns are removed from the screen and a PC mother board map appears. The locations of RAMs as displayed on the screen correspond to their location on the PC mother board when it is in an upright, readable position. Good memory chips are shown as green bars and bad ones are red.

Press the FIRE button to go to the next self test.

TEST

The sixth test also fills the screen with black and white patterns that do not have meaning. The patterns display for about three minutes.

After the RAM is fully tested a mother PC board map appears on the screen. The locations of RAMs as displayed on the screen correspond to their locations on the mother PC board when it is in an upright, readable position. Good RAMs are shown as green bars and bad ones are red.

Press the FIRE button to go to the next self test.

Page 8

SCREEN AND SOURCE SHIFT TEST

  • The seventh test automatically checks other memory and PC board components relating to screen and source shifting and looks like this:

SCREEN SHIFT

SOURCE SHIFT

  • When an OK message appears next to a message on the screen, memory and PC board components are in working order.
  • If a NOT OK message appears next to a message on the screen, suspect chips 7A and 8A on the mother PC board (see schematic "B*W RAM ADDRESSING AND RAMS").
  • Press the FIRE button to go to the next self test.

SCREEN AND SOURCE REVERSE TEST

  • The eighth test automatically checks memory and PC board components relating to screen and source reversal and looks like this:

SCREEN REVERSE

SOURCE REVERSE

  • When an OK message appears next to a message on the screen, memory and PC board components are in working order.
Page 9

If a NOT OK message appears next to a message on the screen, suspect chips 7A and 8A on the mother PC board (see schematic "B*W RAM ADDRESSING AND RAMS").

  • Press the FIRE button to go to the next self test.

ARITHMETIC LOGIC TEST

  • The ninth test automatically checks the arithmetic logic unit registers.
  • The screen displays a vertical stripe which looks like the MAIN SCREEN RAM test. The vertical stripe moves from left to right across the screen for about 30 seconds.
  • When an ALU OK message appears on the screen the arithmetic logic unit is in working order.
  • If an ALU NOT OK message appears on the screen, suspect ALU chips and associated input address lines (see schematic "DATA PROCESSING") and output RAM circuits (see schematic "B*W RAM ADDRESING AND RAMS").

Now the self tests are finished. To get FIRE ONE out of the self-testing mode, find the 8-positon DIP switch on the daughter PC board and set switch 8 to the OFF position. Push the FIRE button to put FIRE ONE back into the attract mode.

Page 10

IIT. OPERATOR OPTIONS:

The AUDIO VOLUME CONTROL pots are located at 13B and 14B on the daughter PC board. With the board in the upright, readable position the pot on the right controls the volume for the player on the right and the pot on the left controls the volume for the player on the left. All the other FIRE ONE operator options are selected by setting the 8-posiiton DIP switch on the daughter PC board. Figure 1 shows all selectable functions controlled by the 8-positon DIP switch.

12345678

ON

OFF

COINA

COIN B

TIME A

TIME B BONUS A

BONUS B

AQT

TEST

Figure 1. Functions of the 8-position DIP Switch

COINAGE

Switch 4 | Switch 3 | 1 Player | 2 Players | Time Coins Coins

OFFOFF1275
OFFONL190
ONOFF22105
onON24120

BONUS DIFFICULTY

Switch 6 | Switch 5 | Difficulty Ships sunk / Sub hits per Player per Minute

OFFOFFEASY12
OFFONAVERAGE16
ONOFFTOUGH20
ONONVERY TOUGH24
Page 11

ATTRACT (Switch 7)

OFF PLAY MUSIC DURING ATTRACT SEQUENCE on NO MUSIC DURING ATTRACT SEQUENCE

TEST MODE (Switch 8)

OFF NORMAL PLAY on RUN DIAGNOSTIC AND OPERATOR ALIGNMENT TESTS

Page 12

Figure 2, Player Control Module

Page 13

Iv. PLAYER CONTROL ADJUSTMENT:

Figure 2 shows the player control module. To adjust the player controls do the following:

  • Unlock and remove the back door of the unit by lifting it up and out.
  • From the inside of the video module, loosen the four bolts connecting the top’ of the player control module to the unit.
  • Go to the front of the unit and open the player control module by lifting it up and out.
  • Locate the 8-position DIP switch on the daughter PC board. Set switch 8 to the ON positon.
  • Press the FIRE button three times to bring up the third diagnostic test.
  • Loosen the setscrew holding the gear belts to the tubes.
  • Set the steering control handle to the center position.
  • Pull the gear belt until the green bars are aligned with the red bar at the center of the screen.
  • Tighten the setscrews.
  • Close the player control module by lifting it up and forward.

1l. Go to the back of the unit. From inside the video module, tighten the four bolts connecting the top of the player control module to the unit.

  • Set switch 8 to the OFF postion and push the FIRE botton to put FIRE ONE back into the attract mode.
Page 14

ve REPLACEMENT PARTS LIST:

The parts list that follows describes the most important FIRE ONE parts including Exidy replacement part numbers and reference locations.

REFERENCE PART NUMBER QTY DESCRIPTION LOCATION

48-2300174L800 TTL LC76
48-2006174802 TTL LC1E
48-201017404 TTL Lc4G
48-2302274LS04 TTL LC1F, 3D
48-2011it74804 TTL LC2¢
48-2312374L808 TTL LC3C, 4D, 8K
48-205227411 TTL Le4E
48-2304174L827 TTL LC4a
48-23241741830 TTL LC7D
48-2222174L855 TTL LC25
48-2341174L886 TTL LC5A
48-2078174L8109 TTL LC1J, 2E
48-2307i74L8138 TTL LC35
48-2321174L8139 TTL LC2D
48-2322574L8135 or 25LS153 TTL LC5B, 5C, 5D,

5E, 8L

48-2101425L8153 or 74153 TIL LC3E, 3F, 8F,

8G

48-2323674L8157 TTL 1c2F, 4B, 4F,

75, 8H, 8

48-2349174L$158 TTL IC7B
48-2308574L8161 TTL IC1G, 1H, 2a,

2G, 2H

48-20971748163 TTL 1¢1D
48-2099174L$164 TTL IC4c
48-2309174L8166 TTL IC7F
48-2107174L8175 TIL 1C3A
48-2109274L8181 TTL IC8B, 8D
48-2347274L8240 TTL IC93, 103
48-2326774L8244 TTL IC3G, 3H, 4J,

5G, 6F, 6G, 7¢

48-2348474L8253 TIL IC6B, 6C, 6D,

6E

48-2121274L8257 TTL IC5J, 65
48-2123174L8273 TTL IC7E
48-2124174276 TTL IC2B
48-2136174L8283 TIL IC8E
48-21532748288 TTL 32x8 ROM or PROM 7A
48-2154Tristate or open collector8A
Page 15

REFERENCE PART NUMBER QTY DESCRIPTION LOCATION

48-2208674L8377 TIL ICSF, 6A, 6H,

7H, 7K, 7%

48-2344182809 or 93419 TTL 64x9 RAM 6K
48-02801Z-80 MOS Microprocessor4H
48-22112LM379IC 42, 43
48-22122NE556Ic 29, 31
48-90673LM558 —*IC 6, 16, 17
48-222123340IC 28,30
48-22063LM3900.IC 2, 4, 14
48-208814006Ic 40-
48-906914013Ic 3
48-907014017.Ic 5
48-209318038:Ic 15
48-906818253-5“Ic 1
48-2089114507 or 4070Ic 41
48-23001741L800 or 7400.IC 26
48-2300174L804 or 7404,IC 34
48-201317406 or 74LS061c 27
48-2315174L8321c 39
48-23072“748138:IC 32, 33
48-2347274L8240IC 37, 38
48-2326174LS244.Ic 25
48-2208274L8377IC 35,36
54-50362Pot w/nut and LW
Page 16

VI. FIRE ONE SCHEMATICS:

Page 17

is

7ALSI6! /3

EXIDY INC. [SYSTEM II LOGIC DIAGRAM PAGE TOFS VIDEO TIMEBASE [__FR30-0004-C [5.086

Page 18

EXIDY INC. +5V. FLO Oy Oe 0: OD, 2325 rseas

7 74Lsi6l

[SYSTEM I! LOGIC DIAGRAM [PAGE 20F6]

CENTRAL PROCESSOR FR30-0004- © $.066

Page 19

EXIDY INC. SYSTEM II LOGIC DIAGRAM 30F 8] MEMORY

Page 20

oour ss

i rs a 7 FL ZDMS| ag ea ‘3 ee t 24200 pay) ea 3 sc a fz

FAs B 12DM3 = oe teal 9 Tels) > ef 20M2 Piet i. Pela 3 [3) EF ZB

EXIDY INC, [SYSTEM 11 LOGIC DIAGRAM PACES OF BI our bs oy BS Rel ess

DATA PROCESSING [__FR30-0004-C"

Page 21

DALUO ale, > Datul 4 oacuade t

1 10,SHMIly 2 0,[2CSRTHé)
roeiALOISSHNzIzlne $ GilsAAS,

SHB 3 ol Aallaticas raLsot pis.a ais ROSH] § SI {2.amut “aD 8% #ROT_2 s|_ 7a EET D > OSPROT F< ~ A ala 4 sHmto_

28 3CINsew le7 2
alg,MocaS

Aiko SEH 23 TE scrarons aa

Wuxa ah)eprot «.

ZRAM BY smaotl til SHMQD jo 1A CSRO H4e 12 AMLO

Fy ! Ey ay oll alae

z a A =U Aas

&.

EXIDY INC. [SYSTEM II LOGIC DIAGRAM JPAGE SOF 8

B=W RAM ADDRESSING ano RAMS FR30-0004- S.066

Page 22

EXIDY INC, SYSTEM [I LOGIC DI RAM

66] COLOR PROCESSING ano MEMORY

Page 23

Pate

Palth777777
Padute 7444444
Paral 4$$s8ss7
la S222222Bs
2°°°°9°d
Pas °i1111i<

a 7

®698C)87H

Ol.Blor 02 sifax COSzar 004 hoe COS oy i

eReory82ecoPAO

Pal 82509/93419C REPLACEMENT a Pad PAS

RO Rl RQ BO 8) Be

iS} G2

a 080 fos} 4 ‘0S! 4} ob 0S2 2] s 083 wu 2 {2 054 i] 4 | Ds5, 4 056 ie] 66 087 ‘

NOTE:

Yor PALSIS7 if SEXT is not used

EXIDY_INC. SYSTEM || LOGIC DIAGRAM PAGE 70F 8] PSEUDO COLOR FR30-0004-C

Page 24

Sas aa

0 MREQ [22 STRANS 65GND ‘GND eas5v [22-0Po [2 "oP} fes-pP2 ['a_oP3 Peei2y 0 412V 82 -5V Bt ev ‘WO DWI [32-pw2 E-OWS

Pal PAZ Teo Pas PBOAOMZZOO Z—-v OO

EXIDY INC. PIC

GREEN OUTPUT

SYSTEM II LOGIC DIAGRAM Pace BOF G] CONNECTORS ano VIDEO OUTPUT FR30-0004- C_ [s.oce_|

Page 25

SHUNT DIP CONFIGURATIONS.

‘only one type is used depending on

memory chip type

R vo}2L0PO co 0

“5Jeei2vM, s2ULOP2
6Pa}7pspaDP3
alSAP oaftoPa=f
Al=)R psisoPSfad
Asc© pe LeOPS2 1c10
AN80M pf20P7Ce

oN P20 Alc Pg PY Pa a P2)

-suMat2v 5)A2vSC.oa
5PsP2) +5)PahJSHUNT DIPS:
allSAANCSA
alSB ANZCSBTYPEROM or PROM
AlcscCSC
ASD AlawCSBWaseo
ON20 GNPe&esceles
AloPio APigB+1. 83168
  • 2516, ie 278 Ite 231 Tard (c20
ws&cs.Rockwell 23168

c Intel 2732 lntet_ 2332 TA. 2532 Ice

esicsDTel. 2716

\c7 TS es

csi Hes

EXIDY INC. [| FIRE ONE] SCHEMATICS [PAGE 1 OF PROGRAM MEMORY L 791017 DESIGNED BY TECHNCAL MAGK | S.066 |

Page 26

MUSICARL 360K MUSIC BRS ROOK | ix L

  • Music cB3 360K | ¢ MUSIC ARG SBOK_ ~ N MUSIC BRESEOK | ix pe c a S6OK ¢ musiccR2RG0K | oy R io. 1039 ® in 1639 _ i C39 ie. id FOR.

OF! i20P2 $1.00 COINL 2DP3 «+5 STAWSTANIC pa +BY. mosomzzon

joanur BN is @

re

EXIDY_INC. | FIRE ONE! SCHEMATICS [PAGE 20F6| INPUT/OUTPUT DESIGNED BY TECHNICAL MAGIC

Page 27

NOISE GENERATOR LOW FILTER cat

RES

AMIXER os R28 10K,

RSPK2 L379 ws C43 aspx a RISO A-l2v LSPKIg} U LSPx2-a} 0 ‘SOUND OFFL> Lgergal ¢

R79 130K RI24 RI25, A OM IL ? , 130K SPK2 yore R TK 4 R80 ‘tid Jeary Rad 13900 R64 fon dibs

DESIGNED BY TECHNICAL MAGIC | $.066_|

Page 28

SHIP EXPLOSION

C98, a) MIX L 1M 1M. RIS2 FRIS3

Riz 39K a3,

FIRE ONE] SCHEMATICS [PAGE 40F6) AUDIO 791017 DESIGNED BY TECHNICAL MAGIC [sos _]

Page 29

S cizol = CG ff 6 © fete oN +5) +5V WE zerkazl =P Ec f *6 N R

c o N Babe al a cuss cn7t 7 vod ¢ ° R so 4!

cist v

—Y__

EXIDY INC. [FIREONE] SCHEMATICS [PAGE SOFG_ CONNECTORS L_ 7910.17 DESIGNED BY TECHNICAL MAGI

Page 30

EXIDY_INC. canar ene

i > —DIVEB ' SPSTNO

fan SPSTNO LEFT 7 RIGHT

vy 3 OIGITAL PCT gy LPO 2 2 DISTAL Tg 2{2-—de1 a] F ; a ea position pfe pps ad BIPSHEN 5 FDP F GRAY CCDF ..-—-—} IK Pare bE 31s ae ® £ + WEB ?] 1 5 Gal FIREB| p | ba 0

3 7 ta out MAT oF SPSTNO

FIRE ONE! SCHEMATICS PAGE 6 OF LOCAL CONTROL BOARDS DESIGNED BY TECHNICAL MAGIC

Page 31

Lacring 1 2 3 4 5 6 7 8 9 10 rt 12 13 14 15, 16

AL Joes fre i Ss ome sa Te SE sas Ga er Shy ame = 3 al, Ga Gey = > Gt GOw enti emik eaie 5 poo qe fc ERE ef, Ee Go OE YB fo or ca dg nn epeand em 48 pw jsscwerf Ysocnerf Ysocnert Jsoenerf Jscenest Jsoexert ] socner ni ened Sf OO ay & Ee sem Sa bors ios & a L ¢ = eo rey Tee res cio itn Tee eis O O Eee = set oP ut Lt tuf def tf ee <r) [czD cu fers Ge ee rey

  • ee otk EE ik © fooonerf fsocrerf Ysoenerf Jsocxerf | suceert Yaoene a x), 6 We iter te EE ee yest a Say Srey S22 ix ise fa3 wie big fat

D é

7 ime ies

+e,

77-3356-16-B

Page 32

9 PIN AESISTOR PAC ane

*:0a
F0 FF4a—TE7J——
spare | © PSasia_|AsFause7P¥acsoa] O b'aissr7__ |745208] © Pr45zee |‘ax eam]Dn kam

C7 Yh

..tx Raw | Ob ae eam | O
z=7%772:5‘
“SPARE14276743isass1]O Pp isssraises]O PD raasisae|:
=14S IALpe

sks acnan ]O

ze, oe.Pa 2PIN RESISTOR PAC
rtny tJ71,10tr%
( OU Paso“aisoe| ) Prasiet#3153 | O P®mesess |‘muses |craw] O Panam | O
“CRYSTAL:+
So‘.rfan raw |) Ban ra
ieTeTYraC3frycyieTALSIBI
5163 |‘aisiaa |= OPauseaso)=OSassrusesa}Pracs30)=i.

% : fi OFF an ew | O Pecan | O

$‘——T *aer)BiennTe ———%,
Faz} O PF arsios|254515374H)Flasiss] O Pauses]7405273TALS 283pan RAM
é:.Op ar raneSan nam |
:.J-AsOra$
T4104]msist]OQ p'BsesisaT405(5TO peesanFAL SI6l2513/53,
...PPauseao | PPrauszaa
—1a5az
Sursict | O P'mesictmaiseaa ] OQ Poa | 239 PSacseas | O p™arszea“aesoo] O sess
  • fe
.]‘ac gan | OQ Pax eam
4156aisict}OU Pp reseaa260 CPU, |7a s3TT1405311415/57.

“hag im an gan |0) ad

)iev) he5
raisioa] () prusss| 34415/38;DS 4use57“aesi5t |. O paesis7OPfan raw | OQ)
RSAO IKEA
a7ie+ 76,
oe."7ALS31141308]Pane 1 Denxam) O

eS :

782509=es4 oe+
.100 PIN EOE CONNECTOR7mast] Q PiaesissOPSareaw | O Pan gana
ole—a31°B

4 } LO OD) Ko en 3102 MOLEX SPIN VIDEO COW. A3 ik IOUS Of W314 RU 410 en @® fe ik eso) at _2n3id2_@) Sgeds8 5 gee § gee g FRE gS S j03,7v4 DE ae MOLEX 3 PIN POWER COAN, ©