The Electric Yoyo
The Electric Yo-Yo (rev 1) (Taito America Corporation, 1982) · Manual · 58 pages · 18 sections · original scan
WAITO) © 1982 Trade Marks of Taito America Corporation

This page is a drawing, shown as the original scan.
Reproduction of this publication is forbidden without the written permission of TAITO
AMERICA CORPORATION, Elk Grove Village, Illinois. This manual is only conditionally
issued, and neither receipt nor possession thereof confers or transfers any right in, or
license to use, the subject matter of the manual or any technical information contained
thereof.
For permission requests, write: TAITO AMERICA CORPORATION 1256 Estes Avenue Elk Grove Village, Illinois 60007 Telephone (312) 981-1000 Telex 25-3290
“THE ELECTRIC YOYO”™ UPRIGHT
TABLE OF CONTENTS
“THE ELECTRIC YOYO"™ GAME SET-UP......... Page 5
1.1 Game Features... 0.0.0... cee eee 6 1.2 Introduction ........ 0... c eee e eee eee 6
4.3 Game Inspection ............-- 00.00 cee eee 6 1.4 Pre-Game Installation ......-..---2--..see sees 6
1.5 Power On/Off Switch, Interlock Switch, Memory Protect Switch, Self Test Switch, Volume Control, and Service Outlet............. 7
1.6 Electronic Acceptors ...........2.....0-00000- 7
1.73Game Installation... 2.0.00... cece ence ees 7 1.8 Self Test Procedure ..........-...02--.e sees ee 8
MAINTENANCE .............. 00.0 c eee eee eee 15
2.1 Cleaning ....... 00.0... cece eee ee eee ee 16
2.2 Coin Door .......... 06. c eee eee eee 16 2.3 Fuse Replacement ...........2...0 2c eee eee 16 2.4 Monitor Removal ...............--22-00e eee 16
2.5 Cover Glass Removal ..
2.6 Printed Circuit Board Replacement ............. 17
2.7 Power Supply ......- 0.00 c eee e eee cence ee 17
2.8 CMOS RAM ........... 0.0 e eee e eee eres 19 2.9 Test Points.............. 0. cece eee eee 19
THEORY OF OPERATIONS ................... ee eee 21
3.1 General... eee erred 22 3.2 Video Board. ........ 6... e cece eee eee ed 22 3.3 Data Sound Board ...........---2--.e eee eee 23 3.4 ROMI/O Board .............2 eee cee eee 24
- ILLUSTRATION & PART LISTS....................4 25
Figure 1 Incandescant Panel ..............2.08 26
Figure 2 4-Way Joystick .....0.. eee 27
Figure 3 Control Panel ...... 0.0... 28
Figure 4 DoorAssembly ..................005 30
Figure 5 = Cabinet Assembly Front View .......... 32
Figure 6 Cabinet Assembly Rear View........... 34
Figure 7 Power Supply Component Layout ....... 36
Figure 8 — Video Processor Component Layout .... .. 39
Figure 9 Data/Sound Processor Component Layout ................. 44
Figure 10 ROM//O P.C. Assembly Component Layout ................. 48
Figure 11 Coin Processor Board Layout .......... 52
Figure 12 Coin Processor Board Schematic ...... . 53 Figure 13 = Wiring Diagram ...........0....00008 54
Figure 14 Power Supply Board Schematic (Fold Out)
Figure 15 Video Processor Board Schematic 1 of 2 (Fold Out)
Figure 16 Video Processor Board Schematic 2 of 2 (Fold Out)
Figure 17 Data/Sound Processor Board Schematic (Fold Out)
Figure 18 ROM/I/O Board Schematic (Fold Out)
LIST OF ILLUSTRATIONS
Figure 1-1 Programming Plug ................... 6
Figure 1-2 Power ON/OFF Switch ................ 7
Figure 1-3 Interlock Switch & Memory Protect Switch7
Figure 1-4 — Self Test Switches ................... 7
Figure 1-5 Volume Control Setting ............... 7
Figure 1-6 — Self Test Button ............ 0. 8
Figure 1-7 Video Board (On Service Door) ......... 9
Figure 1-8 Flow Chart ...
Figure 1-9 Color Bar ..............2. 0... cece 10 Figure 1-10 Color Bar ......... 2... eee cece eee 10
Figure 1-11 Color Bar ...... 0.0... cece an]
Figure 2-1 Coin Mechanism..................-. 16
Figure 2-2 Fuse Replacement .................. 16
Figure 2-3 Monitor Removal ...............--.- 16
Figure 2-4 Cover Glass Removal . .
Figure 2-5 Printed Circuit Boards ............... 17
Figure 2-6 Power Supply ..........0...cee ee ee 17
Figure 2-7 Current Limit Adjustment............. 18
Figure 3-1 Clock Timing.........2....0.. ee eae 22
Figure 3-2 Dual Port RAM Timing ..............6 23 LIST OF TABLES
Table 1-1
Table 1-2
Table 1-3
Table 1-4
Table 1-5
Table 1-6
Table 1-7
Table 1-8
Table 1-9
Table 1-10
Table 2-1
Table 2-2
Table 2-3
Table 2-4
Table 3-1
Table 3-2
Table 3-3 Self Test Switches .................... 7
Hardware Tests ..................000. 8
Video Board ROM Checksum ........... 8
Decoding Jumper Location ............. 8
Video Board RAM Checksum ..........- 9
Data/Sound Board ROM Checksum...... . i)
Screen RAM Content ................. 1
Audit Totals ............ 0. eee eee 12
Standard Coin Setting ................ 13
Custom Coin Setting ................ 13
Line Voltage ................ cee eee 17 Secondary Fuses .............0.000 ee 18
Data/Sound Board Test Points ......... 19
Video Board Test Points .............. 19
Video Board Memory Map............. 22
Register Initialization ................. 23
Data/Sound Memory Map ............. 24
Game Set-Up
- GAME SET-UP
1.1 GAME FEATURES TAITO AMERICA CORPORATION'S ‘THE ELECTRIC YOYO''™ upright game is housed in a compact and highly serviceable cabinet with many added features. A larger security designed cash box has been incorporated into the design of this cabinet. By putting wheels on the cabinet, moving the game from one location to another is made much easier. The Control Panel has a polycarbonate overlay, so cigarette marks and mars can easily be wiped clean. This overlay can be replaced if necessary. The Marquee and Coverglass are made of fully Tempered Glass to minimize breakage. The Back Service Door houses all the P C Boards for the system making servicing of the game, if needed, much easier. Lighted Instructions are provided to further enhance the game and attract players, by making the Instructions easier to read. TAITO AMERICA CORPORATION proudly presents our improved Self-Test capability, making servicing of the game easier, which keeps your game up and running with less down time.
1.2 INTRODUCTION TAITO AMERICA COROPRATION’S ‘THE ELECTRIC YOYO"™ upright game is designed for one or two players. The object of the game is to clear the screen of BLOX by moving the YoYo around the screen and going over each BLOX to eliminate it. The Player must avoid the Trions and the Bions. Trions are triangular, snake-like creatures whose eyes will destroy the YoYo upon contact. The Trions will cause a BLOX to “charge”’ if he hits it unless a BION was on that BLOX. In this case, the Trion picks up the BION, (turns green) and deposits it at the next BLOX hit. The Trion can also pick up a BION which is in free space. The BION is a small creature which moves around the BLOX trying to destroy the YoYo. If they get to the YoYo while it is not energized, the YoYo blows up. The scoring is based on the length of the string thrown out toa BLOX. The value ranges from 10-500 for an uncharged YoYo and 20-1000 for an energized YoYo. The player accumulates a Bonus counter each time he loops a charged brick and energizes. If the screen is successfully completed, this counter is multiplied by 1000 for an end of field bonus. While the YoYo is charged, the BIONS are flashing. If the YoYo can maneuver over the flashing BIONS, the player scores 1000 points for each completed crossing. Make sure the YoYo doesn’t discharge near the BION. Afree turnis issued each time the player accumulates a score set by the location. The default is 50,000 points.
1,3 GAME INSPECTION TAITO AMERICA CORPORATION'S ‘‘THE ELECTRIC YOYO"'™ upright game-is shipped ready for operation, but a last visual check ~ should be made to insure the game is in good condition. Please verify the following before turning the game on. Check the exterior of the game for shipping damage, chips, dents, or broken parts. Open the Rear Service Door and check for any interior damage. “THE ELECTRIC YOYO”™ UPRIGHT
Make sure there isn’t any damage to the wiring. *~ Check Printed Circuit Boards, making sure there is No damage to the components. Check fuses making sure they are firmly in their holders.
- Check for loose foreign objects, especially metal objects which may cause electrical problems.
- Check Plug-in Connectors making sure they are firmly in their sockets.
- Check Self Test Switches making sure they are not damaged.
The Video Monitor is properly adjusted before shipping. If there are any adjustments necessary, refer to our Video Monitor Manual (72-00010-00!) This Manual contains ali the Manufacturers recommendations for adjusting the Video Monitor.
1.4 PRE-GAME INSTALLATION The following precautions should be foliowed when installing the game.
- Avoid rough handling of the game, the picture tube is fragile. Install the game on a level surface. Avoid installing the game where it may receive excessive sunlight or heat, to protect the game from rising internal temperatures. Do not install in a damp or dusty location. For a short time after connecting the power to the game, the picture may be temporarily distorted. *
The monitor's ‘purity is affected by the earth's magnetic field, causing a variation of color. By turning the game on for 10 or 15 seconds and then off for 20 to 30 minutes the automatic degaussing circuit applies a degaussing field around the edges of the monitor. Doing this several times will correct the problem. Another way to correct this problem is to purchase a degaussing coil or bulk tape eraser at any Electronics store. This will help to immediately demagnetize the Video tube. Caution must be used with a degaussing coil so the magnetic field of the degaussing coil is not allowed to become too intense at any one place on the picture tube there by causing a localized cclor distortion. If you move the game to another location after degaussing the Problem may reappear. Refer to Monitor Manual 72-00010-001 for details.
1.4.1 POWER REQUIRMENTS TAITO AMERICA CORPORATION'S ‘THE ELECTRIC YOYO"'™ game is shipped ready for operation at 120 or 240VAC, 60Hz with a power consumption of approximately 250 Watts. The following line voltages may be selected:
100VAC +10% 50/60Hz 120VAC +10% 50/60Hz 200VAC + 10% 50/60Hz 220VAC +10% 50/60Hz 240VAC +10% 50/60Hz
Avoltage Programming Block is located on the primary side of the Transformer to compensate for high/low conditions. (See Figure 1-1).
FIGURE 1-1 PROGRAMING PLUG
For safe operation it is recommended the cabinet be grounded. This game is equipped with a three conductor power cable. The third conductor is the ground conductor and when the cable is plugged into an appropriate receptable, the game is grounded. The offset pin on the power cable's three-prong connector is the ground connection.
1.5 POWER ON/OFF SWITCH, INTERLOCK SWITCH, MEMORY PROTECT SWITCH, SELF TEST SWITCH, VOLUME CONTROL, AND SERVICE OUTLET To minimize the hazard of electrical shock while servicing the game a Power ON/OFF Switch, and two (2) Interlock Switches are provided. Two (2) Self Test Switches, two (2) Volume Control and a Service Outlet have also been provided. (See Figures 5 and 6 for the location of Switches).
1.5.1 POWER ON/OFF SWITCH, INTERLOCK SWITCH A Power ON/OFF Switch is located in the front of the game at the left hand side of the cabinet. There is two Power Interlock Switches, one is located on the inside of the Coin Door frame and the other is located at the inside rear of the Service Door. This switch removes all the power from the game without unplugging it from the wall outlet. Power may be restored for servicing by pulling out on the Interlock Switch Button. Ube id N
FIGURE 1-2 POWER ON/OFF SWITCH
1.5.2 MEMORY PROTECT SWITCH The Memory Protect Switch is used to prevent erroneous writes to locations in the CMOS RAM which store the location program variables.
Coin Door Memory Protect Switch
Coin Door Power Interlock Switch
Back Door Power Interlcok Switch
FIGURE 1-3 INTERLOCK SWITCH & MEMORY PROTECT SWITCH
1.5.3 SELF TEST SWITCH There are two (2) Self Test Switches and four (4) positions, located on the inside of Coin Door. See Figure 1-4. The “YOYO"’™ game is capable of testing itself and provides data to demonstrate that the games circuitry and the controls are working properly. For further
eal on the Self Test Procedure refer to Section 1.8 and
igure 1-7.
age | @ 8 6 | i" x | FIGURE 1-4 SELF TEST SWITCHES abe on & )l6e {SWITCH FUNCTION Up Reset To Factory Setting (Reset Line Lit) Increment Number (Variable Line Lit) Decrement Number Move To Next Line Move To The Next Screen Down Advance Sub-Test Advance Test
TABLE 1-1 SELF TEST SWITCHES
1.5.4 VOLUME CONTROL SETTING The Volume Control Setting is located on the Data/Sound P. C. Board, which is on the Service Door. The volume increases when turned clockwise as indicated in Figure 1-5. Asecond volume contro! can be found on the inside right of the Coin Door frame. The volume increases when turned as indicated in Figure 1-5.
FIGURE 1-5 VOLUME CONTROL SETTING
1.5.5 SERVICE OUTLET A Power Recepatacle has been provided to further aid servicing. The voltage at this receptacle will be the same as the line voltage the game is set at.
1.6 ELECTRONIC ACCEPTORS This game is equipped with the capability of using 12 VDC Electronic Coin Acceptors, such as Third Wave Electronics, Model TW12 or equivalent. Power for these units may be obtained from the Coin Entry Lamp terminals which provide 12 VDC.
1.7 GAME INSTALLATION Open the Coin Door and pull out the Interlock Switch.Tum the game on.See Figure 1-3. The language selection frame should be displayed. If the game is in the game mode, push the Self Test switch toward ADV Sub Test. The game will go into Self Test. If after a minute, the switch test frame is not displayed, refer to the Manual on Self Test. After the Switch Test is displayed push the Self Test Switch toward ADV four more times. Then the language selection frame should then be displayed. Push the Self Test Switch toward ADV Sub Test until the language you want is green. Push the Self Test Switch toward ADV Test and then all the print should be in the language you select. Push Self Test Switch toward ADV Test four more times the game should be in the game mode. For more information on the options the operator can use, see Section 1.8.17 thru 1.8.21.
1.7.1 GAME ADJUSTMENTS There are several adjustments you can make to the game to make the play easier or more difficult. First, Maximum Credits defines a limit for the machine, which when crossed will disable the coin slots. This will allow the location to set a limit on the amount of games a player will get if there is a line of people waiting. This value ranges from 1 to 99. However, it should not be set so close to 99 that a single coin can overflow the credits issued (maximum 99). A Free Play mode may be selected by setting maximum credits to 0. Next is the Number of Turns which regulates the number of YoYo's on the playfield. This can be set from 1 to 3. Next is the Table Mode this should be set to ON for the Table Top and OFF for the Upright version. Attract Sound should be set to ON for sound and OFF if no sound is preferred. The Difficulty setting is used for the number of Bions on the Playfield, this determines the difficulty of the play since the more Bions on the Screen the more difficult the play. HSTD Enable when set to 1 this will be displayed in the attract mode, if set to 0 the HSTD will not be displayed. Bonus Turns is set from 1 to 9. The number set is then multiplied by 10,000 before and extra Bonus turn is received.
1.8 SELF TEST PROCEDURE 1.8.1 GENERAL The Self Test Procedure is performed using the two (2) Switches located on the right inside corner of the Cabinet, and the Self Test Button and the LED’S on the Video PC Board. (See Figure 1-7).
FIGURE 1-6 SELF TEST BUTTON
1.8.2 ENTERING INTO THE SELF TEST MODE To enter the Self Test Mode, press the Advance Sub-Test Switch located on theCoin Door or the Self Test Button found near the LED display. All the LED'S should blink on and the Hardware Tests should start. If a continual test of the Video Board is desired, press the Self Test Button twice to start the Video Test in the Auto Test Mode. In this mode, the machine will continually run the Hardware Test until powered off. If the message “OPEN COIN DOOR TO TEST” appears, the Coin Door must be opened or a jumper connected across J19, 1-2. This is because the CMOS RAM Test cannot be perfomed with the memory protected by the Coin Door Switch. 1.8.3 HARDWARE TESTS These tests are performed in the following order:
VIDEO BOARD ROM Checksum Communications RAM CMOS RAM Color RAM Screen RAM DATA BOARD ROM Checksum Local RAM Communications RAM Handshake Test
TABLE 1-2 HARDWARE TESTS
All LED values are shown Left to Right. 0 is OFF, 1 is ON and X is dependant upon the test results.
1.8.4 VIDEO BOARD ROM CHECKSUM The Rom Checksum calculates the checksum of each Video ROM and compares it to the checksum stored for that ROM. If it differsfrom the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED’S.
LED VALUES: TESTIN PROGRESS: 00 0001
FAILURE: O1 XXXX
| LED VALUE | VIDEO | 2732 | | |
| 07 0000 | ‘A000-AFFF | U5 | |
| 01.0001 | B000-BFFF | U6 | |
| 01 0010 | C000-CFFF | U7 | |
| 01 0011 | D000-DFFF | U8 | |
| 01 0100 | E000-EFFF | ug | |
| 01 0101 | FOO0-FFFF | U10 |
TABLE 1-3 VIDEO BOARD ROM CHECKSUM If the Checksum ROM is bad, it will show U10 to be bad first. If this test fails, the ROM indicated on the LED display or the supporting circuits will need to be replaced. The E-PROM Memory in a given game may be implemented as banks of either 2716 or 2732 —-PROMS. The E-PROM type for each bank is selected by the decoding jumper 26-00002-016 for 2716 or 26-00002-032 for 2732.
E-PROM BANK LOCATION VIDEO ut DATA U22 SOUND U29
TABLE 1-4 DECODING JUMPER LOCATION
1.8.5 COMMUNICATIONS RAM FROM VIDEO BOARD The Communications RAM Test determines the stability of memory shared by the two processors by storing a predefined series of numbers throughout the RAM, then reading it back to insure that it was stored correctly.
LED VALUE: 00 0010
A failure has been detected when the machine halts with the above display. Failure of Communications RAM during Video Board Tests may result from either defective RAM circuitry or failure of the Data Board. To isolate the failure, disconnect the Data Board at P6 and re-enter the test. A failure means trouble in U3, U4 or associated circuits. Passing the retest suggests Data Board problems.
1.8.6 VIDEO BOARD CMOS RAM After saving values in another portion of memory, the CMOS RAM is tested in the same manner as the Communications RAM. If the CMOS RAM passes the test, all of the locations are restored to their previous values.
LED VALUE: 00 0011
A failure of the CMOS RAM has been detected when the machine halts with the above LED value displayed. If this occurs U85 and U86 or associated decoding should be checked.
1.8.7 VIDEO BOARD COLOR RAM This tests the system Color RAM by storing predefined sequences of numbers in the Color RAM, then reading them back while testing for accuracy.
LED VALUE: 00 0100
A failure is indicated by the processor halting with the above value displayed on the LED'S. This signifies the need to check U56, U57 and associated multiplexing and decoding.
1.8.8 VIDEO BOARD SCREEN RAM The Screen RAM is tested by writing a pattern to each page on the screen. The results of these writes is then compared to the original pattern. Any discrepancy causes the machine to halt with the LED displaying the faulty RAM.
LED VALUE: TEST IN PROGRESS: 00 0101
FAILURE: X XXXX
| LED VALUE | RAM | 11_XXXX. | RAM | |
| 10 0000 | U33 | 11 0000 | U66 |
| 10 0001 | U32 | 14 0001 | U65 |
| 10 0010 | U31 | 11 0010 | U64 |
| 10 0011 | U30 | 110011 | U63 |
| 10 0100 | U29 | 11 0100 | U62 |
| 10 0101 | U28 | 11.0101 | U61 |
| 10 0110 | U27 | 11.0110 | U60 |
| 10 0111 | U26 | 110111 | U59 |
| 10 1000 | U17 | 11 1000 | U48 |
| 10 1001 | U16 | 11 1001 | U47 |
| 10 1010 | U15 | 11 1010 | U46 |
| 10 1011 | U14 | 111011 | U45 |
| 10 1100 | U13 | 11 1100 | U44 |
| 10 1101 | U12 | 111101 | U43 |
| 10 1110 | Ut1 | 11.1110 | U42 |
| 10 1111 | U10 | 414111 | U4 |
TABLE 1-5 VIDEO BOARD RAM CHECKSUM.
Upon failure of a screen RAM, locate the problem RAM and replace it. Exchange suspected RAM with a known good location to determine if the problem moves with the RAM IC or whether the problem is in the supporting circuitry, further testing can be done with the Color Bar Test. If this Diagnostic appears to halt without indicating a RAM failure (00 0101 on LED'S), a failure to begin the next test (Data Hardware) is indicated. The interconnection to the Data Processor must be in place and the Data Processor must be functional to continue. SELF TEST LEDS
oo 0000
FIGURE 1-7 VIDEO BOARD (ON BACK SERVICE DOOR) 1.8.9 DATA/SOUND BOARD SELF TESTS DATA HARDWARE (ROM CHECKSUM) The ROM Checksum calculates the checksum of each Data ROM and compares it to the checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED'S.
LED VALUE: TEST IN PROGRESS: 00 0110 FAILURE: 01 XXXX
LED VALUE DATA 2732
| 0000 | A000 | ut4 |
| 0001 | 000 | U15 |
| 0010 | coo | uis |
| 0011 | Doo | ui7 |
| 1100 | ooo | U18 |
| 1101 | F000 | uig |
TABLE 1-6 DATA/SOUND BOARD ROM CHECKSUM
If this test fails in the field, the bad ROM will need to be replaced. To aid the technician in diagnosing difficult boards, hold the Self Test Button located on the Video Board depressed while the game is being powered on. This will cause the game to enter the diagnostic mode directly upon power up, accessing only one ROM per processor. Games which otherwise will not execute the on board diagnostics will thereby provide more information on ROM failure.
1.8.10 DATA/SOUND BOARD LOCAL MEMORY The Data processor uses a known sequence of numbers to test the bits in its Local Memory. If a bad bit is found the machine will halt with the following display.
LED VALUE:
1.8.11 COMMUNICATIONS RAM ADDRESSING The function of this test is to ensure that both the Data and the Video Processor address the Communicatons RAM in the same manner. The Data Processor requests the Video Processor to fill the RAM with a known pattern then, the Data Processor compares the result to the expected pattern. If it does not match, one of the processors is probably decoding the address incorrectly as the RAM itself was previously tested for stability by the Video Processor. The machine will halt with the following display.
LED VALUE: — 00 1000 9 00 0111
1.8.12 DATA/VIDEO HANDSHAKE This test ensures that the Data Processor can send priority commands via interrupts to the Video Processor. The Video Processor is halted, then restarted by the data Processor after the proper command acknowledgements are received. The machine will halt with the following display.
LED VALUE: 00 1001
1.8.13 SWITCH TEST This screen is used to determine all switches are working order before entering the switch dependent self-test screens. The Wiring Diagram supplied with each game will indicate the number associated with a particular switch. The switch numbers appear in green if the switch is closed and white if it is open. The Advance Test Switch (Switch number 9) is always red in order to set it apart from the others on the screen, switch 29, 30, 31, 32 are not used & stay green. The user should check all other switches before pressing the Advance Test Switch, as this would move him to the next screen. In addition to the switches required, by the game, the User should be sure to test the Advance Sub-Test, UP and DOWN Switches located in the bottom right inside corner of cabinet for proper closure as these switches are used to move about in the Self-Tests Screens. To advance to the next screen, activate the Advance Test Button located at the bottom right inside corner of cabinet.
GAME OVER
"ADVANCE ‘SUB-TEST
ene r ow curcxsuml oo 000 — EME ‘COMMUNICATIONS RAM Y 06 6010
coon aA ai} 90 0101 aaa
- (eauney mou cuecksum { co 011001 HEX ‘communications RAM Y 00 1600 Wanoskaxe TEST] 09 1001
‘swiven TEST
ALIaNMENT-convencence SCREEN, TESTS LOCATION PROSRAMMING H1GH SCORE TO DATE avorr torats
GAME OVER
FIGURE 1-8 FLOW CHART 1.8.14 COLOR BALANCE AND INTENSITY ADJUST SCREEN This screen is comprised of two sections. The first section provides a method for adjusting the intensity level of each color gun, and achieving an initial color balance. Three squares, one blue, one green and one red, are drawn along the top of the screen at minimum intensity or brightness. The color guns should be adjusted so that these squares are barely visible and of equal intensity. To complete the color adjustments, a gray scale is provided at the bottom of the screen. Fine tune the color balance with this scale, the double check that the squares at the top are barely visible. To advance to the next screen, activate the Advance Test Switch located on the bottom of cabinet. 1.8.15 COLOR BARS The CPU divides the screen RAM into 16 areas corresponding to 16 bars on the screen. Each area is written with a data value from the Table 1-7. Each value exercises one bit in the screen RAM. The Color RAM is written with a pattern which outputs each data value with a recognizable color from the table. All other data values are coded black. This results in a normal screen of 16 colors bars per the following Figure. AO O_O O_o OA NON RGN GN WP o® OM dPep> OP AP oh ah ad AD AN AY A! RS § wt ot CCCI M6 0 0% PY AC OP GO AN AN AN AN AO ON AN Ad PPM oF MP or ANA N WAS Speer SOOFF glg]alz e/5/2)8 2/2] als|% BLU vio H
BLU-GRN
$0000 —t ISFFOO COLOR BAR DIAGNOSTIC NORMAL FIGURE 1-9 COLOR BAR
BLK avy ak
© O_o 0.0 * a SoH esl Wns Maal NN AN AO ONAN AS nS aS aS AN AO NE OP oO © oF 10 gO QO nd OPO" gO” GOGO ANY OPO AN ror OF MOM AALOP AN LP FP ON ON SrEFF
$0000 ISFFOO
COLOR BAR DIAGNOSTIC BIT 03 STUCK LOW IN 1-BANK FIGURE 1-10 COLOR BAR
SCREEN RAM DATA CONTENT
DOO NAN A NAR GN AS oO AS AAS SAS aS Sota SONS AR NO gh ah aN KR aS SS aS a we oYgS SFFFF
ISFFOO
COLOR BAR DIAGNOSTIC BIT 5 STUCK HIGH ALL BANKS
FIGURE 1-11 COLOR BAR SCREEN RAM CONTENT COLOR RAM ADDRESS
| BAR # | COLOR | _|HEX | BINARY | BIT TESTED | |
| 1 | Red | (vy | 0000 0001 | 0 |
| 2 | Orange | 02 | 0000 0010 | 1 | |
| 3 | Yellow | 04! | 0000 0100 | 2 |
| 4 | Green | 08 | 0000 1000 | 3 | |
| 5 | Blue Green | 10 | 0001 0000 | 4 | ||
| 6 | Blue | 20 | 0010 0000 | 5 | |
| 7 | Violet | 40 | 0100 0000 | 6 | |
| 8 | White | 80 | 1000 0000 | 7 | |
| 9 | Red | FE | 1111 1110 | 0 |
| 10 | Orange | | FD] | 1111 1101 | 1 |
| 11 | Yellow | FB) | 1111 1011 | 2 |
| 12 | Green | F7 | 1111 0111 | 3 |
| 13 | Green Blue | EF | 11101111 | 4 | ||
| 14 | Blue | DF} | 11011111 | 5 |
| 15 | Violet | B7 | 1011 1111 | 6 | |
| 16 | White | F7 | 0441 1111 | 7 | |
| None | Black | XX | XXXX XXXX |
TABLE 1-7
If the Self-Test passes, errors in those circuits which affect CPU access are ruled out. This leaves latches U91, U94, shift registers U95, U96 and U105-109, direction select U81 and U104 and the CR side of select U81 and U104 and CR side of the Color RAM MUX U55, U73, and U74. Stuck bits may be indentified by observing abnormal bars. A bit stuck high will result in black bars (two bit high) on the left or top half of the screen except for the bar associated with the stuck bit. On the right of bottom half, the bar associated with the stuck bit will be black. The converse is true of a bit stuck low. An error across the entire bar indicates an error in the shift registers, direction select, or color RAM MUX which affects every pixel. Lines of error running crosswise to the bars indicate an error in one bank of RAM if every eighth pixel. To move to the next screen, activate the Advance Test Button. If self test fails, the color bars still may by useful. This screen may now be entered without going through on-board self test. Use “Advance Test’’ to enter the high score screen then ‘‘Down’’ to enter the Switch Test. Advance Test may then be used to access color bars. 1.8.16 ALIGNMENT AND CONVERGENCE TEST This screen is provided to align the color guns and correct the convergence on the screen. The screen is composed of a red anda green rectangle and white grid. Adjust the screen width and length so that the red rectangle is slightly within the boundaries of the tube. The adjustment is to be made on the center of the lines which make up the rectangle. The corners of the rectangle will extend beyond the shadow mask. The green rectangle defines the normal playfield and so should be visible from the players view point. A grid of white squares is provided to help detect and correct any convergence problems the tube may have. Adjust the monitor until the squares are of equal size throughout the screen. To advance to the next screen, activate the Advance Test Button on the bottom right inside corner of cabinet.
"
1.8.17 LOCATION SELECT SCREEN(LANGUAGE SELECTION) This screen allows the user to select the language in which the Location Select and the game will operate. Four (4) languages are provided. Use the Advance Sub-Test Button to move through the offered languages. When the desired language is green, depress the Advance Test Button, to advance to the next screen.
1.8.18 LOCATION NAME SELECTION This screen allows the user to program the location name. Alpha, numerical and miscellaneous charecters are provided. Use the Advance Sub-Test Button to move to the next character position indicated in green. Use the UP/DOWN switch to reach desired character, set by depressing Advance Sub-Test Button. Continue until location name is completed, depress Advance Test Button to advance to next screen.
1.8.19 LOCATION SELECT This screen allows the location to define various game control parameters. The User selects the line to be changed by using, the Advance Sub-Test Button until the desired line is changed to green. The value associated with this line is then modified with the UP or DOWN switches. If the machine is to be reset to the factory setting, use the Advance Sub-Test Button until the reset line is lit in green, the press the UP switch. The values will be reset and the user will be ‘placed back on the first line for further adjustments. Advance test will move to the next screen at any time. The maximum credits defines a limit for the machine, which when crossed will disable the coin slots. This allows the location to set a limit on the amount of games a player will get if there is a line of people waiting. This value ranges from 1 to 99. However, it should not be set so close to 99 that a single coin can overflow the credits issued (maximum 99). A Free Play Mode may be selected by setting maximum credits to 0. The credits per coin are set in the coin slot Selection Screen. The number of turns defines how many turns per credit. This value ranges from 1-5. Table Mode defines what type of cabinet the game is in. Settings are 0 upright 1 Cocktail Table . Attract Sound defines whether or not the User chooses to have sound produced from the machine during Attract Mode, having 1 as ON and 0 as OFF. The difficulty factor allows the user to set the difficulty from 0-9 using 2 as factory setting. HSTD (High Score to Date) enables the User to disable all HSTD functions, set at 1 for ON and O for OFF. Bonus turn allows the User to choose if a bonus turn should be awarded. 0 disables bonus. Other values set Bonus at 10,000 points.
1.8.20 HIGH SCORE TO DATE SCREEN This screen shows the scores and initials of the players with the ten highest scores. It is used as an audit for the game. To reset the values, press the UP Switch. This will also set the initials to the default values. When the UP Button is activated it resets to default scores. To move to the next screen, activate the Advance Test Button in the bottom right inside corner of cabinet.
1.8.21 AUDIT TOTALS This screen provides the audit totals for the game. Once they are recorded, they may be zeroed by pressing the UP Switch. The following audits are kept. Total Credits The total number of paid credits issued. This total is never zeroed, but it will wrap around to zero when its total reaches 1,000,000. The only time this total can be zeroed is by physically removing the battery or jumper W1, while the power is off. The number of coins dropped into the left slot. The number of coins dropped in the center slot. The number of coins dropped into the right slot. The number of credits issued for coins. The number of credits awarded by the game. Awarded credits / paid credits + awarded credits *100 Number of minutes the game has been in play mode. Number of minutes the game has been in extended or awarded play. % Free Time Awarded minutes / minutes played “100. Average Game (Sec) | Minutes played / paid credits + awarded credits *60 The number of times which a player scored high enough to bump someone else from the high score list. Left Coins
Center Coins
Right Coins
Paid Credits Awarded Credits
% Free Plays
Minutes Played
Minutes Awarded
High Scores
TABLE 1-8 AUDIT TOTALS
The UP Switch is used to zero the audits. To advance to the next screen, activate the Advance Test Button in the bottom right inside corner of cabinet. Total credits will not turn to zero unless battery voltage is removed from CMOS memory. 1.8.21 COIN SLOT SELECTION This screen allows the user to either select a standard coinage setting for the game or program his own. If a standard setting is desired, use the UP and DOWN Switch to adjust the coinage setting while itis litin green. The values for the variable will change as this number is altered. When the right selection is set, use Advance Test to return to the game. If a non-standard setting is desired, use Advance Sub-Test Switch to move down to the variables so that they may be programmed individually. Once this switch is pressed, the setting number is set to zero to show that the location has supplied their own settings. As the lower variables are unchanged, the user may minimize his effort by first selecting a setting close to the one he desires. Once in the programming mode, the Advance Sub-Test Switch is used to move among the variables. It will also take you back to the standard settings, if you press it by mistake. The UP and DOWN Switches are used to increment or decrement the values. Advance Test Switch will return to the game when pressed. The coin multiplier tells how many coin units are issued for each coin through a particular slot. Coin units for credit show the number of units necessary before a credit is issued. Coin units for bonus gives the number of units necessary before a bonus credit is issued. Minimum coin is an optional value which will keep the credits from accumulating until the specified minimum amount of coin units is reached. It is not used in any of the standard settings.
1.8.23 CMOS MEMORY FAILURE If the message ‘Memory Failure - Service Required’ appears on the screen, the CMOS RAM which stores all of the location programming has failed. All the values stored in the RAM are set back to factory defaults. This condition probably indicates a battery failure, ora failure of U85 or U86. Refer to Section 2 on Maintenance 2.7.6 CMOS RAM. STANDARD COIN SETTINGS TABLE 1-9
_|2ls 212/2le/¢ 2lz(sielElelé
elel8/s|/2}2lsg ee: &|3|8l2|s|3s|s COIN DOOR MECHANISMS CREDIT/MONEY
| STANDARD | 1.25, 4/91 | 0 | 04 | 01 | 00 |
| 1/.50, 3/91, 6/82 | 02 | 04 | 01 | 00 | |
| 1/.50 | 03 | 04 | 01 | 00 | |
| 1 DM, 5 DM | 1/1DM, 6/5DM | 04 | 00 | 01 | 00 |
| 1 FRANC, 5 FRANC | 1/2F, 3/5F ONLY | 05 | 16 | 06 | 00 |
| 25 CENTS, 1 GUILDER | 1/25, 4/1G | 06 | 00 | 04 | 00 |
| 5 FRANCS, 10 FRANCS | 1/5F, 2/10F | 07 | 00 | 02 | 00 |
| 41/10F | 08 | 00 | 02 | 00 | |
| 1 FRANC, 2 FRANC | 2/1F, 5/2F | 09 | 04 | O01 | 00 |
| 1 UNIT, 5 UNITS | 1/2, 3/5 | 10 | 00 | 06 | 00 |
| TWIN COIN | 4/1 COIN | 01 | 04 | 01 | 00 |
| 1/2 COINS | 03 | 04} | 01 | 00 |
CUSTOM COIN SETTINGS TABLE 1-10
Ss . B|3 oe =/2|-
| 3 | z | 3/8) | 5/6 |
z 2/s/ele/é
| & | 8|zZ|38|8]| | = |
COIN DOOR MECHANISMS CREDIT/MONEY
| STANDARD | 1/.25, 5/91 | 00 | 04 | 01 | 04 | 00 | |
| 2/.50, 5/#1 | 00 | 04} | 01 | 04 | 02 | |
| 2/.50, 4/91 | 00 | 04] | 01 | 00} | 02 |
| 1/.50, 3/81, 4/91.25 | 00 | 12 | 03 | 15 | 00 | ||
| 1/,50, 3/61, 7/82 | 00 | 48 | 12 | 96 | 24 | ||
| 25 CENTS, 1 GUILDER | 1.25, 5/1G | 00 | 00 | 04 | 104 | 00 | |
| 100 LIRE, 200 LIRE | 1/200 LIRE | 00 | 00 | 02 | 00 | 00 | |
| TWIN COIN | 1/3 COIN, 2/5 | 00 | 00 | 02 | 00 | 00 | |
| 1 UNIT, 5 UNITS | 11, 5/5 | 00 | 00 | 05 | 00 | 00 | |
| 1/3, 2/5 | 00. | 00} | 10 | 00} | 00 |
NOTES
Maintenance
ALL GAMES REQUIRE A CERTAIN AMOUNT OF MAINTENANCE TO KEEP THEM IN GOOD WORKING ORDER. A PERIODIC CHECK OF THE MECHANICAL CONTROLS WOULD BE BENEFICAL TO THE SUCCESS OF YOUR GAME.
2, MAINTENANCE AND REPAIR 2.1 CLEANING The exterior of the game, all metal parts and all plastic parts can be cleaned with a non-abrasive cleanser. Caution should be used when cleaning the glass; a dry cloth can cause scratches and result in a foggy appearance.
2.2 COIN DOOR The Door used in “THE ELECTRIC YOYO"’™ UPRIGHT game needs little or no maintenance, See Figure 2.1. If desired a special coin mechanism cleanser, that leaves no residue, can be obtained from your distributor. Refer to the manufacturers documenation of additional information is needed.
FIGURE 2-1 COIN DOOR
2.3 FUSE REPLACEMENT This game contains eight (8) fuses. Two (2) fuses can be found on the Regulator PCB and five (5) can be found on the Transformer Assembly. Two (2) fuses are located at the bracket where the AC line cord comes into the cabinet. See Figure 2-2 for locations of these fuses.
FIGURE 2-2 FUSE REPLACEMENT 2.4 MONITOR REMOVAL If you need to remove the Video Monitor, follow the instructions listed below:
It is recommended the game be left disconnected for at least one hour before removing the Video Monitor. This will probably discharge the Video tube but EXTREME CAUTION is still necessary.
Disconnect power from the line voltage. Remove the Control Panel by releasing the two spring loaded latches. Disconnect the Wiring by separating connector V and all wire to the CRT. Remove (2) rear carriage bolts and lower Monitor on side rails. Remove (4) bolts, one on each corner of the Monitor Bracket, slide Monitor out toward you. soe eos
Use EXTREME CAUTION and do not touch electrical parts of the Monitor Yoke area with your hands or with any metal object in your hands! High voltages may exist in any Monitor, even with power discon-
FIGURE 2-3 MONITOR REMOVAL
If you move the game to another location after degaussing the
‘problem may reappear. Refer to Monitor Manual 72-00009-001 for further details.
2.5 COVER GLASS REMOVAL To remove the Cover Glass follow the instructions listed below:
- Remove the control panel by reaching up through the Coin Door and unlatching the latching clamps. Remove the (3) Screws on the Cover Glass Bracket. Hold Glass firmly slide out from the rear. Be sure you are holding the glass firmly to ensure against any chipping or breakage. Pe N
FIGURE 2-4 COVER GLASS REMOVAL
2.6 PRINTED CIRCUIT BOARD REPLACEMENT You may wish to remove “THE ELECTRIC YOYO"’™ printed circuit board, Video Processor (08-00001-001), Data/Sound Board (08- 00002-002), ROM/I0 Board (08-0003-002) or Coin Door Processor (08-00039-001) for servicing. Refer to Figure 2-5. “THE ELECTRIC YOYO"'™ Printed Circuit Boards (PCB) are located on the inside of the service door for easy access. To remove the boards the following steps should be followed:
- Open the Service Door, the power will automatically be removed by the Interlock Switch located on the inside of the door frame.
- Disconnect the connectors from the board or boards you wish to remove.
- Disconnect the ribbon cable, connecting the boards by spreading eject latches on the connector.
- Remove the screws for the boards you wish to remove. FIGURE 2-5 PRINTED CIRCUIT BOARD
2.7 POWER SUPPLY The Power Supply produces all the necessary game voltage requirements. Refer to Figure 2-6 while reading the following circuit description.
FIGURE 2-6 POWER SUPPLY 2.7.1 AC INPUT The AC Input Voltage is applied to the main Power Supply via the AC Line Cords, Line Filter, Line Fuse, Power Switch and Interlock Switch. Different Line Cord are used for 120V and for 240V. The Line Fuse is located on the Line Cord Assembly near the Strain Relief. A Voltage Programming Block is located on the primary side of the Transformer to compensate for high/low voltage conditions. The following line voltages may be inserting the appropriate Programming Plug.
Line Voltage i Line Fuse 100 VAC + 10% 50/60Hz 120 VAC + 10% 50/60Hz 200 VAC + 10% 50/60Hz 220 VAC + 10% 50/60Hz 240 VAC + 10% 50/60Hz
TABLE 2-1 LINE VOLTAGE
For continous protection against fire hazard, replace only with a fuse of the same type having the same electrical rating.
There are five secondary sources. Three go to the Regulator PCB providing +5VDC, +12VDC, —12VDC, and —5VDC. The other two are fused 6.3VAC used for the incandescent lighting and fused 120VAC used for the monitor, and in certain models for a fluorescent lamp and fan. These secondary fuses are located on the bracket adjacent to the Power Transformer.
TABLE 2-2 SECONDARY FUSES
2.7.2 —5VDC AND —12VDC REGULATORS The AC Input for the negative voltages comes into the Regulator PCB on J1-5 and J1-6 from the Transformer. Fuse F3 protects against short circuits. The AC voltage is then full wave rectified by BR3 and filtered by C16. The raw DC is then applied to Reg 1, a three terminal —12V Regulator. The output of this Reguattor is the —12VDC output for the system and is also the input voltage for Reg 2, a —5V Regulator. The output of this Regulator is the —-5VDC for the system. Capacitors C17, C18, C19 are to improve the transient response and stability of the minus voltage regulator. Diodes D8 and D9 provide protection against C18 and C19 being shorted through the Regulator. Resistors R34 and R35 provide current limiting for LED'S 3 and 4 which will light when there is voltage present at the regulation outputs.
2.7.3 +5VDC REGULATOR The AC Input for the +5VDC Regulator circuit comes in on J1-4 and J1-2, via F1 into BR1. BR1 full wave rectifies the AC Input. This raw DC is applied to the collectors of (2) series pass transistors, mounted on the Heat Sink Assembly. The regulation is done by U3, which is a voltage regulator whose output controls the gain of Q5, which in turn controls the gain of the series pass transistors. The emitter of the series pass transistor returns to the Regulator PCB and through R16 and R18, which serve to force current sharing between the series pass devices. The voltage at the output of R11 and R12is the +5VDC for the system. R11 and R12 are voltage set and current foldback adjustments respectively. Q8, D3 and R20 comprise a SCR- Type Crowbar Circuit which will trigger when the DC output voltages rise above 5.8V. Once the SCR fires, the Power Supply has to be turned off to reset the device. R19 is a current limiter for the voltage indicator LED 1. R16 is used to set the output voltage of the Regulator. C8, D2, R13 and Q4 delay the start-up of the 5V Regulator to allow the —5VDC Regulator to stabilize first. 2.7.4 +12VDC REGULATOR This circuit is essentially the same as the 5V Regulator described above. The AC current comes in on J1-3 and J1-4, via fuse F2 into BR2. The AC is rectified by BR2 and filtered by C9. The raw DC is fed toa single series pass transistor on the Heat Sink Assembly and also powers the +12V and +5V Regulator. R28 and R25 are voltage set and current foldback and factory adjusted to 12 Volts +.25V at 4 AMPS. D7, Q9, and R31 are SCR Crowbar Circuits which trigger at 13VDC output which causes supply to go into current foldback. There is an RC delay as in the 5V circuit to delay the +12V rise time.
2.7.5 RESET CIRCUIT The reset circuit will output a 2sec active low MRST pulse at J3-14 and J4-14 when the power is first turned ON and whenever power fails for more than 35ms. The reset circuitry is comprised of a Dual Timer (556) and an optical coupler across an AC secondary. The output of U1 is the input to one half of the 556 which is configured as a missing pulse detector. Ci and R3 determine the time before the output goes active. This is set for about 35ms. When two or more cycles are missing, the output of the first timer triggers the second timer which drives the MRST low for about 2 seconds. The timer constant for the second timer is set by R4 and C6. Power on reset is generated by C4, and R39 and D12 on the trigger input of the second timer. Q3 inverts the signal out of the 556 so it is active low. R7 insures MRST is low while the power is rising.
2.7.6 POWER SUPPLY ADJUSTMENTS VOLTAGE Adjust voltage on +5V and +12V for +5.00V to +5.05V and +12.00V to +12.05V. CURRENT LIMIT Adjust control (51, 121) counterclockwise until voltage just changes then turn control clockwise until voltage goes back to original value. With pointer, mark position of arrow on potentionmeter then turn control until beginning of 1st notch is aligned with the pointer. On the controls with the Blue Disk turn approximately 30°.
FIGURE 2-7 CURRENT LIMIT ADJUSTMENT
If voltage adjustment will not bring voltage up, set current limit adjustment to 12 value.
2.8 CMOS RAM !f when powering the game up, it will not coin up because the battery is low. The following procedure should be followed. Open the Service Door of the game and pull out Interlock on the Video Board (Blue jumper). Push interlock back in. Wait 2 minutes, power back on and insert W1 back in. If the Language Select frame does not come on the CRT, power down, remove W1 again. Short pins 18 and 9 on U85, power back on and insert W1 back in. Leave the game on for 12 hours. If this procedure does not work when you turn the game back on the battery may need to be replaced.
2.9 TEST POINTS The following is a list of Test Paints to be used when troubleshooting.
DATA/SOUND
E (Master Clock) Q (Master Clock) uc Last Interlock Complete SA 15 (Address Line} DA 15 (Address Line) Voice Clock SBSC (Sound Processor Data Enable)
DBSC (Data Processor Data Enable)
+5V Ground
TABLE 2-3 DATA/SOUND BOARD TEST POINTS
VIDEO BOARD
(Clock Video Processor) (Clock Video Processor} Last Instruction Complete
(Video Data Enable) (Address Line)
TABLE 2-4 VIDEO BOARD TEST POINTS
lf you ground any Data Enable Test Point (DTP7, DTP8, VTP7) the related processor will receive No-OP instructions and the address line will act line a 16 Bit Counter.
NOTES
Operation
THIS SECTION PROVIDES A TECHNICAL DESCRIPTION OF “THE ELECTRIC YOYO"’™ GAME. THE GAME ELECTRONICALLY CONSISTS OF PRICTED CIRCUIT BOARDS, TV MONITOR, POWER SUPPLY, AND SPEAKERS WHICH ARE DE- SCRIBED IN DETAIL IN THE FOLLOWINT TEXT.
- THEORY OF OPERATION 3.1 GENERAL The TAITO AMERICA CORPORATION'S arcade video system game is an advanced multiprocessor based circuit utilizing the Motorola 6809E microprocessor. The system is organized in three logical blocks:
A. The Data Processor, which supervises the operation of the entire system. B. The Video Processor, which performs ail screen based functions, such as playfield image motion, line drawing, etc. C. The Sound Processor, which generates sounds under the direct control of the Data Processor.
\n order to facilitate easy inter-system communications, the Data and the Video Microprocessors run synchronously using clock and timing signals developed on the Video Board. For this reason, discussion will begin by examining the Video Board.
3.2 VIDEO BOARD 3.2.1 SYSTEM CLOCK The fundamental system clock is developed by the 20MHz crystai, inverters U24 and U39, and components. The 20MHz signal is divided by the high speed flip flop U38 to obtain 2 10MHz main clock with a precise 50 percent duty cycle. This 10MHz signal generates all other fundamental timing signals for the video system, including the Data Processor. 1C23 divides the 19MHz signal to obtain 5MHz, 2.5MHz and CCLK, and their respective inversions. IC’s U9, U37, and U38 combine these signals, presenting them to U25, which synchronizes the output signal to the system 10MHz clock. This circuit produces waveforms whose active edges are synchronized to 15ns worse case, 2ns average. The characteristics of the clock circuit may be noted by reference to the Timing Diagram, Figure 3-1. 3.2.2 SCREEN RAM The Video Processor controls a Screen RAM of 256 x 256 pixels with 8 bits per pixel. In order to access of this information, the screen is divided into two pages, top and bottom, chosen under software control. These pages are both addressed at 0000 - 7FFF with address 0 corresponding to the lower left corner of the screen (horizontal scan). All CRT accesses to this RAM are transparent to the processor and the RAM may be read or written any time. The timing of the Screen RAM and the eventual scan is controlled by a 6845/6545/46505 CRT Controller Chip. it’s address outputs are gated by U19, U20, U50, and US1 for inversion when when a cocktail table mode. The scan addresses are multiplexed with the address present on the microprocessor data bus by U35, U52, U53, and U54 for standard RAS-CAS accessing. The desired bank of memory is addressed by U87, a one of four decoder. Data written into the Screen RAM comes directly from the system data bus, buffered by 33 Ohm resistors. If a processor read is taking place, the data is placed on the data bus by U77, U78, U79, and U80. Screen reads are latched by 374’s U91, U92, U93, and U94. A second screen read is then performed, and this data, together with the data from the screen read previously performed and latched by the 374’s is presented to the eight (8) 74LS299 shift registers. These registers may be shifted in either direction for cocktail table implementation. The byte stream then proceeds to the Color RAM.
Dual Port RAM CMOS Battery Backup Memory . LED Output and Color RAM Page Select Data FIRQ Activation Address Video FIRQ Deactivation Address Color RAM Address Latch Hi-Byte Address Latch Lo-Byte Address Latch Indexed Screen Location Scan Line Readback Location CRT Controller Base Address
| rn | FSH | HH | L |
| ase | lV | nN | TABLE 3-1 VIDEO BOARD MEMORY MAP |
asi he ose 5 3.2.3 DUAL PORT RAM
| ba | = | a | This RAM may be accessed in its entirety by either processor. This |
eo is arbitrated as follows: z T
= AS h iN 1. The Data Processor runs in quadrature with (one quarter
| ad | + | i | clock cycle ahead of) the Video Processor. In other words, |
| = | = | i | E is inverted for use as DQ, and Q becomes DE. Refer to |
ed Le Timing Diagram. Figure 3-2.
| a | a | + | | | —- | 2. The Data Processor, by nature of this timing, accesses the |
| cms | qe | 4 | { | Dual Port RAM % cycle before the Video Processor. At this | |
| mae | t | £ | > | point the Video Processor is guaranteed to not be |
+ !
FIGURE 3-1 CLOCK TIMING accessing the RAM. The Data Processor access is flagged by U36, which causes a Cycle to be stolen from the Video Processor’s main clock, VQ and VE.
- The Video Processor is unable to access the Dual Port RAM unless the Data Processor is not accessing it as it will not be receiving clocks during that time. The cycle steal is accomplished by the generation of signal DPMUX by U36. This signal directly steals the cycle, and also folds over multiplexers U5, U6, and U21, switching the address lines, R/W and gating signals. U1 and U2 gate the data to or from the desired processor. U22 insures that no spurious writes are generated during foldover.
» : _
4 ws : ‘ ons ve ae eee a w \ « [ wos ve —| ro} — P= a onus {= t +— an f il 1 F; FIGURE 3-2 DUAL PORT RAM TIMING
3.2.4 CMOS RAM The CMOS RAN is impiemented for use as both a battery back-up storage area and a work area for the Video Processor. The gating U100, U101, U102, and U103 insure that writes to the block RAM from $8700 - 87FF cannot be performed unless the Coin Door is open (J19-2 grounded). The 3.6V NiCAD battery is trickle charged by Q8, R64, and R65 when the system is powered. When turned off, supply current for U85, U86, and U100 is provided by this battery. U100 is included to solidly gate the MRST signal and prevent invalid operations during power Up and Down. LED and Color RAM Page Latch, U72 is addressed at address $8800. The upper six bits drive LED’S on the circuit board for diagnostics which cannot be done through the screen. The lower 2 bits select the Color RAM page and will be discussed later.
3.2.5 BI DIRECTIONAL FIROQ CAPABILITY To provide for immediate inter-system communication on demand a Bi-Directional FIRQ Capability has been provided. Any access of address $8C00 by the Video Processor will generate a FIRQ to the Data Processor. Any access of $8001 by the Video Processor will remove a FIRQ generated by the Data Processor to the Video Processor. This is accomplished by U7, U8, and U9.
3.2.6 COLOR RAM The Color RAM is used as a translation matrix so that a number of different pixel values may access a given color, or to change the color of a given area of the screen without rewriting the Screen RAM. The serial bit stream, eight bits wide, comes from the shift registers of the Screen RAM to be presented to multiplexers U55, U73, and U74. These select between the Video Processor bus and the serial bit stream. As processor access times are considerably greater than the basic bit time (200ns), it is necessary to access this register only during retrace times. Bus read/write occur through U75, and serial output is latched by U76. This Data Stream is converted to a color pallet of 64 colors and four intensities. When the serial bit is selected for access, the two high order bits are provided by the LED output latch. This allows the Programmer to select between four pages of RAM rapidly. 3.2.7 ADDRESS LATCH CIRCUITRY Two methods of Screen Memory Address are provided:
- A 16 bit address may be written into latch U70 and U71 addressed at $9402 and $9403, The addressed location may be accessed by reference to location $9400.
- The high order bit of the latch selects one of two pages which may be directly addressed by reference to locations $0000 - $7FFF. U36, U70, and U71 latch the address. U36 is used in conjunction with U70 as U70 and U71 are tri-stated when inactive. The screen address deposited on the LA bus by U84 and U98 for Processor Bus accesses, and by U70 and U71 for
latched Address. Decoding is performed by U87
and U88.
3.2.8 SCAN LINE READBACK When read, this location is the number of the scan line currently being drawn by the beam. U34 latches the last row address drawn, and U101 prevents erratic updating at the end of a horizontal line. There are 256 valid scan lines 00 - FF.
3.2.9 CRT CONTROLLER The 6845/6545/46505 is a software programmable sync and scan generator. It has two ports based at $9CO0 and $9C01. It is recommended that the reader consult Motorola, Hitachi, Rockwell, or Synertek supplied documentation. Register initialization are as follows: Intalization (decimal RO | Honzontal total-1 40 Horizontal displayed Horizontal sync position Sync pluse width Vertical total-1 Vertical hold adjust Vertical displayed Vertical sync position Scan lines per row-1 TABLE 3-2 REGISTER INITIALIZATION All other registers are cleared. The interlace capability which differentiates the various types is not used in this application.
3.3 DATA/SOUND BOARD The Data Processor runs synchronously to the Video Processor, as was described in this (Section Dual) Port Memory. All basic timing signals originate on the Video Processor Board and are bussed onto the Data Processor Board. The Sound Processor and Amplifier circuitry also resides on this Board.
3.3.1 MEMORY MAP The following devices are available for access to the Data Processor.
Dual Port Memory Local Memory ACIA Base Address Video FIRQ Activation Address Data FIRQ Deactivation Address Sound PIA Game PIA 1. Game PIA 2. Game PIA 3. A. B. C. D.
E. Ei G. H.
TABLE 3-3 DATWSOUND MEMORY MAP
3.3.2 DUAL PORT MEMORY See discussion of Dual Port Memory under Video Processor Heading (Section 3.2).
3.3.3 LOCAL MEMORY This is a 1K block of memory, U15 and U16, provided for scratch and work area for the Data Processor.
3.3.4 ACIA A Motorola 6850 ACIA has been provided for diagnostic and other communications. Timing is generated by crystal oscillator Y1- U23 and prescaled by U27 and U26. SW1 may be configured to allow one of eight baud rates (2 speeds may be software selected in the ACIA). Correct RS-232 levels are provided by U25 and U21.
3.3.5 BIDIRECTIONAL FIRQ CAPABILITY Any access of $8C00 will generate a FIRQ to the Video Processor. Any access of $8C01 will remove FIRQ generated by the Video Processor to the Data Processor. This is accomplished by U7, U8, and U9, which resides on the Video Board.
3.3.6 SOUND PIA Both ports of PIA U20 have been dedicated to the control of the Sound Processor. Port A is used to select a sound number, which is initiated by strobbing the U20 (CA2) - U8 (CA1) interrupt line. Responses can be made using the reverse U8 (CA2) - U20 (CA1) interrupt. Port B is used to control the amplitude of the generated sound to two Stereo Amplifiers. The output of side B go to U24 and U28, which vary the ratio of the voltage divider across the noninverting inputs of U29 and U30. This allows spatial positioning of a sound to coincide with real time events occuring on the screen, as well as a time based envelope control.
3.3.7 GAME PIA’S Three 6820’s are provided for interfacing with Play Controls and Coin Door Switches. These are located on the Game Board and are accessed through a Jumper Cable J16 and J15 respectively. 3.3.8 SOUND PROCESSOR A Motorola 6802 also resides on the Data Baard for sound generation. This Processor runs at 3.68MHz and accesses only two devices, PIA’S U7 and U8. U8 as mentioned previously, interface to the Data Processor. It also is the digital to analog output of the Sound Processor. Data from Port B is presented to U13. The current based output is converted to a voltage output by Q1, and controlled in amplitude by a potentiometer placed across J8. Speech circuitry is mixed with sound by R9, and the sumis sent to the Amplifiers. U7 controls the speech synthesis chip U19. The
speech signal is shaped and filtered by the multipole bandpass filter
3.4 ROWVO BOARD This board contains the Program ROM for both the Data, Video and Sound Processors, along with the PIA’S needed to interface control, coils, lamps, etc.
3.4.1 GAME PIS’S Three Game PIA’S are located on this board $9400, $9900, $9C00. These devices, U11, U20, and U30 respectively, interface through noise control circuits A or B filters for those lines dedicated to inputs. Eleven (11) High Current Drivers have been provided utilizing circuit C. Each of these is capable of switching a 1.5AMP/ 24Volt DC load to ground.
3.4.2 ROM’S Eight ROM locations are provided for the Data Processor, U12 - U1S. These are selected by U21. Eight ROM’S, U3 - U10 selected by U2 are dedicated to the Video Processor. Sounds are supported by ROM’S U25, U26, and U27, with select U28. ROM Bank U3 - U10 may consist of either 2716 or 2732 type EPROMS as determined by a jumper plug inserted in U1. It is assumed that all such EPROMS in the bank ate of the same type. Likewise, ROM Bahk U12 - U19 is determined by jumper plug at U22 ROM Bank jumpering for 2716's is as follows: Pin 1-14, 2-13, 3-12, 4-11 and 5-10. The highest address EPROM is U10, U19, or U27 in each bank with addresses of adjacent sockets progressing downward in $800 byte blocks. Jumpering for 2732's is as follows: Pin 2-14, 3-13, 4-12, 5-11, and 6-10. The highest address EPROM is U10, U19, or U27 in each bank with addresses of adjacent sockets progressing downward in $1000 byte blocks.
*
illustration &
ists
Parts L
+) -«
INCANDESCENT PANEL
TAITO ITEM PART NO. DESCRIPTION 1 27-00006-001 | Lamp 47 2 26800009-001 | Bayonet Base Socket 3 61D00112-001 | Marquee Lighting Plate
ry
! 2
SF LY
\ <>
gee ke
4-WAY JOYSTICK
ITEM DESCRIPTION TAITO PART NO 63B00071-002 Ball & Shaft 63A00074-001 Mask 63C00069-002 Mounting Plate 62A00004-001 Shock Mount Pad 63A00070-002 Switch Plate
te 63A00080-001 Actuator 63A00072-001 Switch Spacer 29B00033-001 Leaf Switch 63A00073-001 Spacer 61A00227-001 Spacer Metal 2] 2] 0]=)s)o)a|a]o]o)=
58A00006-001 Spring
Ce ee
CONTROL PANEL
TAITO PART NO. DESCRIPTION 29B00016-001 |Leaf Switch 54A07001-008 |Stamped Nut 5/8-11 63C00025-001 | Switch Housing 63B00071-002 | Ball & Shaft 63B00024-001 |Push Button (White) 63D00082-001 | Decal, Lexan 07M00051-005 | Control Panel Assembly 42D00017-001 | Control Panel Wood 61A00015-001 | Strike Hook 42B00108-001 | Cleat 63D00067-002 | Control (4-Way, Leaf Switch)
ae CONTROL PANEL
DOOR ASSEMBLY
TAITO ITEM PART NO. DESCRIPTION 1 04-00037-002 | Lock Kit 2 61D00079-001; P.C.Board Mounting Plate 3 08-00042-001 | Game P.C. Board Assembly
- 79-00031-001 | L.E.D. Values Sheet 5 08-00001-001 | Video Board 6 08-00003-002 | ROM//0 Board 7 sae Data/Sound Board 8 08-00039-001 | Coin Processor Board *Item not shown on drawing
wee DOOR ASSEMBLY
CABINET ASSEMBLY FRONT VIEW
TAITO ITEM PART NO. OESCRIPTION 1 07M00055-004 | incandescent Panel 2 63B00006-003 |‘\U’ Channel Bracket 3 47D00012-007 |Marquee 4 61000115-001 |Marquee Retaining Bracket 5 61D00012-001 |Lower Coverglass Bracket 6 07-00052-005 |Contro! Panel Assembly 7 07-00115-001 |Coin Door 8 61B00113-001 |Switch Bracket 9 07M00057-001 |Service Switch Assembly 10 29-00022-001 |Slide, Center Return Switch WW 29B00015-001 {Interlock Switch 12 61B00114-001 [Interlock Switch Bracket 13 59-00008-001 |Latching Clamp 14 63B00002-004 |“‘T’” Molding 15 29A00023-001 |Power ON/OFF Switch 16 41-00015-002 [Finished Cabinet
CABINET ASSEMBLY FRONT VIEW
CABINET ASSEMBLY REAR VIEW
TAITO ITEM | PART NO. | DESCRIPTION [a 07-00083-001 | Speaker Assembly 2 61800009-001 [Speaker Grill 3 41000015-002 [Finished Cabinet 4 63C00035-001 | Monitor Shroud 5 47M00013-007 [Coverglass 6 07M00042-001 [A/C Line Cord Assembly 7 61800030-002 [Interlock Bracket [8 29800015-001 [Interiock Switch 9 07M00039-001 | Power Supply 10 61600054-001 {Cash Box Lid i" 31B00006-001 |19” Color Monitor 0019-001 {Cash Tray Separator 61B00039-001 |Cash Tray Handle 61DG0060-001 | Cash Box 63R00010-001 | Cash Tray (only) 07M00054-001 | Cash Tray Assembly 08-00002-002 |Data/Sound P.C.B. 08-00033-001 |ROM/O P.C.B. 04-90037-002 |Lock Kit 08-00001-002 |Video Processor P.C. B. 61D00079-601 |P.C.B. Mounting Plate 45C00002-001 |Lock Assembly 61B00142-001 |Lock Rod Assembly 61A00111-001 |Lock Rod Bracket
CABINET ASSEMBLY REAR VIEW
POWER SUPPLY COMPONENT LAYOUT
g Fa Fen GH & : | Pee
° F3 > Qo °
5 2 8 $
o
; =o [|]
a, i OF U st rug “ws NI J0VW
EXO) oD ‘Ou 3 | < D & [ricy) [78] Cy «I C=O of) = Q OR Qe
) wD = @ u = . Q Ge 4 5 7 G@> & ss LA a 80 @) e [esr] ap x
WO = Ee )agg
POWER SUPPLY
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | ‘SYM | PART NO. | DESCRIPTION |
| R1_| | 11-00001-102 | Resistor 1.0K 5% %4W 5% | C5 | 12-10001-102 | Capacitor, .001uf |
R2 | 11-00001-512 | Resistor 5.1K ¥4W 5% C6 | 12-30001-106 | Capacitor, Tantalum 10uf
| R3_| | 11-00001-183 | Resistor 18K %4W 5% | C7 | 12-20003-509 | Capacitor, Electrolytic 50,000uf |
R4 | 11-00001-224 | Resistor 220K %W 5% C8 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V
| R5__| | 11-00001-472 | Resistor 4.7K %4W 5% | C9 | 12-20003-209 | Capacitor, Electrolytic 20,000uf |
R6 | 11-00001-222 | Resistor 2.2K %W 5% C10 | 12-10001-332 | Capacitor, Ceramic .0033uf R7 | 11-10001-101 | Resistor 100 %W 5% C11_ | 12-30001-476 | Capacitor, Tantalum 47uf R8 | 11-00001-102 | Resistor 10K %4W 5% C12 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V
| RQ} | 11-00001-472 | Resistor 4.7K YW 5% | C13_| | 12-10004-103 | Capacitor, Ceramic .O1ut |
R10 | 11-10001-101 | Resistor 100 %W 5% 12-10001-102 | Capacitor, .001uf R11 | 11-30001-015 Resistor .15 4W 5% C14 C15 12-30001-476 | Capacitor, Tantalum 47uf R12 | 11-30001-015 | Resistor .15 4W 5% C16 | 12-20002-108 | Capacitor, Electrolytic 1,000uf
| R13 | 11-00001-472 | Resistor 4.7K %4W 5% | C17_| | 12-30001-225 | Capacitor, Tantalum 2.2uf 25V |
R14 | 11-00001-222 | Resistor 2.2K %4W 5% C18 | 12-30001-225 | Capacitor, Tantalum 2.2uf 25V R15 | 11-00001-222 | Resistor 2.2K %W 5% C19 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V
| R16 | 11-60001-252 | Pot 2.5K %4W 20% | Fi | 24-00003-010 | |10A Fuse | ||
| R17_| | 11-00001-222 | Resistor 2.2K %4W 5% | F2 | | 24-00003-010 | |10A Fuse |
| R18 | 11-60001-102 | Pot 1.0K %4W 20% | F3__| | 24-00003-003 | |Fuse, 2A |
R19 | 11-00001-511 | Resistor 510 YaW 5% F4 | 24-00003-004 | Fuse, 4A
| 11-10001-470 | Resistor 47 2W 5% | F5 __| 24-00003-004 | |Fuse, 4A |
11-00001-162 | Resistor 1.6K YW 5% BR1 | 13-00100-025 | Diode Bridge 25A, 100V 11-00001-103 | Resistor 10K %W 5% BR2 | 13-00100-012 | Diode Bridge 12A, 100V 11-00001-472 | Resistor 4.7K %4W 34 BR3 | 13-00100-002 | Diode Bridge 2A, 100V R24 | 11-00001-222 | Resistor 2.2K %4W 5% D1 | 13-14002-001 | Diode IN4002 11-60001-102 | Pot 1.0K %W 5% D2 | 13-14002-001 | Diode IN4002
| 11-00001-472 | Resistor 407K %4W 5% | D3_| | 13-10752-001 | Diode, Zener IN752 |
11-00001-222 | Resistor 2.2K %4W 5% D4 | 13-14002-001 | Diode IN4002 11-60001-252 | Pot 2.5K %W 20% D5 | 13-14002-001 | Diode IN4002 11-00001-472 | Resistor 4.7K %4W 5% D6 | 13-14002-001 | Diode IN4002 11-00001-122 | Resistor 1.2K %4W 5% D7 _| 13-10964-001 | Diode, Zener IN964 11-10001-470 | Resistor 47 Y4W 5% D8 | 13-14002-001 | Diode IN4002 11-30001-015 | Resistor .15 4W 5% D9 | 13-14002-001 | Diode IN4002 11-00001-222 | Resistor 2.2K %4W 5% D10 | 13-14002-001 | Diode IN4002 Resistor 1.2K VW 5% D11_| 13-14002-001 | Diode IN4002 Resistor 510 %W 5% D12 | 13-14002-001 | Diode IN4002 Resistor 2.2K Y4W 5% LED1| 13-00001-001 | LED (Red) LED2} 13-00001-001 | LED (Red) LED3} 13-00001-001 | LED (Red) LED4} 13-00001-001 | LED (Red) 12-30001-225 | Capacitor, Tantalum 2.2uf 25V U1 | 15-62500-001 | Opto Coupler H11AA2 U2 _| 15-50556-001 | Timer (Dual) 556 U3 | 15-50723-001 | Voltage Regulator 723 12-30001-105 | Capacitor, Tantalum 1.uf 35V U4 | 15-50723-001 | Voltage Regulator 723
POWER SUPPLY
TAITO SYM | PART NO. DESCRIPTION REG1| 15-57912-001 | Voltage Regulator 7912 REG2| 15-57905-001 | Voltage Regulator 79L05 Qi | 14-22905-001 | Transistor 2N2905 Q2 | 14-22905-001 | Transistor 2N2905 Q3 | 14-22905-001 | Transistor 2N2905 Q4 | 14-22905-001 | Transistor 2N2905 Q5 | 14-23055-001 | Transistor 2N3055 Q6 | 14-22905-001 | Transistor 2N2905 Q7 | 14-20030-001 | Transistor TIP-30A Q8 | 14-26401-001 | SCR 2N6401 Q9 | 14-26401-001 | SCR 2N6401 J1 | 25-00022-006 | Connector, 1-380999-0 6Pin J2 | 25-00022-008 | Connector, 350212-1 8Pin J3 | 25-00002-014 | Connector, 09-60-1141 14Pin J4 | 25-00002-014 | Connector, 09-60-1140 14Pin 24-10001-001 | Fuse Clips 30-00220-002 | Heat Sink Dual To-220 30-00003-001 | Heat Sink Single To-3
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
TAITO TAITO SYM} PART NO. | DESCRIPTION SYM |PARTNO. | DESCRIPTION C1 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | C55 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% C2 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C56 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% €3_ | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 57 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C4 | 12-10002-104 | Capacitor Geramic, .tuf,50V, +80/-20% 58 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 5 { 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/--20% 59 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—36 6 | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20% C60 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| ¢7_| | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% | | | 61 | [12-30001-106 | Capacitor Tant, tOuf, 16V |
| 8 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | €62_| | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% |
9 | 12-30001-106 | Capacitor Tant, 10uf, 16V 663 _| 12-30001-106 | Capacitor Tant, 10uf, 16V C10 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C64 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20%
| C11 | 12-10002-104 | Capacitor Ceramic, -tuf,50V, +80/—20% | C65 | 12-10001-471 | Capacitor Ceramic, 470uf,50V, 10% X7R |
12 _| 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% Axal Lead cta | 12-10002-104 } Capacitor Ceramic, .tuf,50V, +80/—20% | 66 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20%
| C14 | 12-10003-101 [canctor Gram | Oop, 10% NPO Ail Lead | C67_| | 12-10002-104 | Capacitor Geramic, 1uf,50V, + 80/—20% |
Cis | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +60/—20% C68 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% 616 | 12-10002-104 | Capacitor Ceramic, -1uf,50V, +80/—20% C69 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C17 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C70 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/--20% G18 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% | C71 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| C19 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% | C72_| | 12-10002-104 | Capacitor Ceramic, 1uf,60V, +80/-20% |
C20 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% 73 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 21 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—-20% C74 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% _| 12-30001-106 Tcapactor Tant 40uf, 16V C75 | 12-16002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C76 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| 626 [ 42-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | C77_| | 12-30001-106 | Capacitor Tant, 10uf, 16V |
C27 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% C78 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 28 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/--20% 79 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| 29 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | “ | aan ine Soosoter Ta 1Ouf,18V | 5 |
12- z ‘apacitor Ceramic, .1uf,50V, +80/—20%
| 630 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% | a2 | pack | a |
€31 | 12-10003-101 | Capacitor Disk 100pf, 10% NPO C82 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| _ | 12-1002 104 | Capacitor Geramio, 1uf,S0V, +-80/—20% | 83 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—36 |
- | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/--20% GBA _| 12-10002-104 | Capacitor Ceramic, Tuf,50V, + 80/— 20% 34 | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20% C85 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| 635 | 12-10002-104 | Capacitor Ceramic, .Tuf,50V, +80/—20% | C86_| | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20% _ | |
| 12-10002-104 | Capacitor Ceramic, .1uf,S0V, +80/-20% | €87_| | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/-20% _ | |
12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 88 | 12-20001-107 Capactor Eectoyic, 100uf,25V, 12-10002-104 | Capacitor Ceramic, .1uhS0V, +80/—20% a9. | 12-20001-107 | Capacitor Electrolytic, 100uf, 25, 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% +100/—20% 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20% | 90 [eee Capacitor Electrolytic, 100uf,25V, 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% +100/—20% 12-16002-104 | Capacitor Tant, 10uf, 16V C91 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 43 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% 92 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/ -20% | 44 | 12-20001-106 | Capacitor Tant, 10uf,16V 693 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | 45 | 12-30001-106 | Capacitor Tant, 10uf, 16V 694 { 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/--20% 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C95 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, 80-20% | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 96 | 12-10001-471 Capacitor Cerasnic, 470pf,50V,10% X7R ial Leac 12-10002-104 | Capacitor Ceramic, .1uf.50V, +80/—20% = - = -10001-471 | Capacitor Ceramic, 470pf,50V,10% X7R
| 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20% | sl | Daniella 9-7 pani | |
| 12-10002-104 | Capacitor Ceramic, -1uf,50V, +80/-20% | _} — | F'¢9g | [12-10001-471 | Capacitor Ceramic, 470pf,50V, 10% X7R |
L Axial Lead
VIDEO PROCESSOR
| TAMO | | | TAITO | ||
| sym | PART NO. | | DESCRIPTION | _| | [sim [parrno. | | nescareTion |
| C99 | 12-10002-104 | Capacitor Ceramic, Tuf,50V, +80/~20% | R37_| | 11-00007-473 [Resistor 47K OHM, TW, 5% |
100] 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% 38 | 17-00007-382 | Resistor 3300 OHM, YW, 5% C101} 12-10008-100 | Capacitor Ceramic 10pf. 10% NPO Axial R39 _| 11-00001-331 | Resistor 330 OHM, HW, 5%
| Ud | _| | [Rao | 11-00001-331 | Resistor 330 OHM, AW, 5% |
| Ci02| 12-10002-104 | Capacitor Ceramic, tuf,50V, +60/~20% | far | 111-00007-331 | Resistor 230 OHM. GW. Sv |
| C103 12-40002-104 | Capacitor Ceramic, .iuf,50V, +80/—20% R42 | 11-00001-331 | Resistor 330 OHM, YAW, 5% | C104] 12-10002-104 | Capacitor Geramio, 1uf,50V, +80/—20% R49 _[ 0007396 | Rat 290O8M, HW, 5% 105 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% R44 | 11-00001-331 | Resistor 330 OHM, %W, 5%
| [ioe [12-t0002-104 | Capacitor Ceramic, tuf,S0V, +60/—20% | pas} | 11-00007-161 | Resistor 150 OHM. HW. % |
Gi07| 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% [R46 | 11-00001-820 | Resistor 82 OHM, TAW, 5%
| [ 6108] 12-10002-104 | Capacitor Ceramic, uf,60V, +80/—20% | par | 111-00001-471 | Resistor 470 OFM, YW, 5% |
| 0118] 12:1001-471 | Capactor Ceramic, SO, 10% 47OPF | jaar | [f-aooni-teallResiaer 160 OHM. aw, Bre |
[it | 11-00001-330 | Resistor 33 OHM, YW, 6% R49 | 11-00001-271 | Resistor 270 OHM, YAW, 5% : R50 | 11-00001-473 | Resistor 47K OHM, YAW, [22] TE OOOON 52 | Resistor 1.5K AW, 9% R51 | 11-00001-390 | Resistor 33 OHM, AW me
| [23 _[ tooo | [Resistor 270 OFM, Hv | ET ate as | ae |
| “T_114-00001-271 | Resistor 270 OHM, %W, 5% | L | ee |
[5 | 11-00001-271 | Resistor 270 OHM, YAW, 5% RS [11 0001-330. | Resietor 33. OHU, ai: 6%
| 6 _| 11-00001-382 | Resistor 3.3K, 4W, 5% | ™ | See hacen es _ |
BZ_{1-00001-221 | Resistor 220 OHM, HW 576 R56 | 11-00007-330 | Resistor 39 OHM. YAW, %
| RB | 100001: 222 | Resistor 2.26, HW, 9% | R57_[ | 11-00001-380 | Resistor 33 OHM, YW, 5% |
| fa | 77-00001-390 | Resistor 33 OHM. "Yaw, 5% | R59 | 11-00001-473 | Resistor 47K OHM, Y4W, 5% |
Riz | 1-00001-330 TResstor 33 OFM ‘GW R60 | 11-00001-332 | Resistor 3300 OHM, YAW, 5%
| ara’ | F17-o000t-8a0 | Reslsor 82 OHM VaW *E | pt | [11-0000%-304 | [Resistor 390 OHM, AW, 5% |
| R14 | 17-00001-181 | Resistor 180 OHM, %4W, 5% | SE | TOOT Se |RSS | Se AO | |
| Ri6’ | 11-00001-151 | Resistor 150 OHM, YW, 5% | - | , | — |
R17 | 11-00001-151 | Resistor 150 OHM, YAW, 5% R65 _| 11-00001-151 | Resistor 160 OHM, HW, 5% R18 | 11-00001-271 | Resistor 270 OHM, YW, 5% a ee ae = =
| BIS | _{1100007-181 | Resistor 180 OM, HW, 5% | R68_| | 11-00001-332 caaer aK aa | : | ||
| R20 | {11-00001-820 | Resistor 82 OHM, YAW, 5% | _{ | Resistor | 3.3K. | AW, | Ste |
R21_|[11-00001-330 | Resistor 33 OHM, “AW, 5% R69 _| 11-00001-382 | Resistor 3.3K, YW, 6% |
| R22 | 11-00001-330 | Resistor 33 OHM, JAW, 5% | FB1_| | 17-00001-001 | Ferrite Bead | |
| R23 | |11-00001-330 | Resistor 33 OHM, YAW, 5% | Fe2_|/17-00001-001_{Fentte Bead | |
| R24 | |11-00001-330 | Resistor 33 OHM, YAW, 5% | FBS _| ¥7-00001-001i| | Ferrite Bead |
R25 | 11-00001-330 | Resistor 33 OHM, YW, 5% FB4 | 17-00001-001 | Ferrite Bead
| R26 | 11-00001-330 | Resistor 33 OHM, YAW, 5% | | | eee ee eee | |
| R27_| | 17-00001-330 | Resistor 33 OHM, AW, 6% | ; | |
| R28 | 11-00001-181 | Resistor 180 OHM, AW, 5% | F7_|'17-00001-001 | [Ferrite Bead | |
| R29 | |11-00001-471 | Resistor 470 OHM, YW, 5% | FBB_| | 17-00001-001 | Ferrite Bead |
| R30 | 11-00001-471 | |Resistor 470 OHM, YW, 5% | FB9_| | 17-00001-001 | Ferrite Bead |
R31_|11-00001-471 | Resistor 470 OHM, VW, 5% F810 | 17-00001-001 | Ferrite Bead
| R32_| | 11-00001-471 | Resistor 470 OHM, V4W, 5% | Fe 14 | 17-00001-001 | Farite Bead | |
| R33 | |11-00001-471 | Resistor 470 OHM, YAW, 5% | Qi | | 14-23904-001 | Transistor NPN Silicon (2N3904) |
| aaa | 17-00001-681 | TResistor 80 OFM Taw 58 | 2 | 14-23904-001 | Transistor NPN Silicon (2N3904) | |
| as | TT1-0000791 | Resistor S00 ORM Yaw Me | @3 _ | 14-23904-001 | Transistor NPN Siicon (2N3904) | |
| soe | [boost | Restor 83 OHM, AWTS | (04 | 14-23904-001 | Transistor NPN Silicon (2N3904) |
a
VIDEO PROCESSOR
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | SYM |PART NO. | DESCRIPTION |
Q5 | 14-23904-001 | Transistor NPN Silicon (2N3904) U11 |15-10001-001 | RAM 16K x 1 Dynamic (4116) Q6 | 14-23904-001 [Transistor NPN Silicon (2N3904) 26-00001-016 | Socket DIP 16 Pin for U11 Q7 | 14-23904-001 | Transistor NPN Silicon (2N3904) U12 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) Q8 | 14-23905-001 | Transistor NPN Silicon (2N3905) 26-00001-016 | Socket DIP 16 Pin for U12
| LED1 | 13-00001-001 | |L.E.D. RED, TL-1% | U13 |15-10001-001 | RAM 16K x 1 Dynamic (4116) |
| LED2 | 13-00001-001 | |L.E.D. RED, TL-1% | 26-00001-016 | Socket DIP 16 Pin for U13 |
| LEDS }13-00001-001 | |L.E.D. RED, TL-1% | U14 |15-10001-001 | RAM 16K x 1 Dynamic (4116) |
| LED4 | 13-00001-001 | |L.E.D. RED, TL-1% | 26-00001-016 | Socket DIP 16 Pin for U14 |
| LEDS | 13-00001-001 | |L.E.D. RED, TL-1% | U15 |15-10001-001 | RAM 16K x 1 Dynamic (4116) |
| LED6 | 13-00001-001 | |L.E.D. RED, TL-1%4 | '26-00001-016 | Socket DIP 16 Pin for U15 |
Yi | 19-00003-001 | CRYSTAL, 20,000MHZ U16 }15-10001-001 | RAM 16K x 1 Dynamic (4116) 20-00001-001 | Battery, NICAD, 3.6V, 1/3 AA 26-00001-016 | Socket DIP 16 Pin for Ui6
| SW1 | |29-00017-001 | Switch Momentary | U17 |15-10001-001 | RAM 16K x 1 Dynamic (4116) |
| TP1 | |59-00021-001 | Test Point | 26-00001-016 | Socket DIP 16 Pin for U17 |
| TP2 | |59-00021-001 | Test Point | _U18}15-00003-001 | CRT CONTROLLER 68A45 |
59-00021-001 | Test Point 26-00001-040 | Socket DIP 40 Pin for U18 59-00021-001 | Test Point U19 | 15-20086-001 | Quad 2 Input Exclusive or (74LS86) 59-00021-001 | Test Point U20 | 15-20086-001 | Quad 2 Input Exclusive or (74LS86) 59-00021-001 | Test Point U21 |15-20157-001 | Multiplexer Quad 2-Input (74LS157) 59-00021-001 | Test Point U22 |15-20032-001 | Quad 2 Input or (74LS157) 59-00021-001 Test Point U23 | 15-20161-001 | Counter, 4 Bit Presetable (74LS161) 11-50001-102 | 1K OHM Resistor Sip Pack U24 | 15-20004-001 | Inverter, HEX (74LS04) 11-50001-473 |47K OHM Resistor Sip Pack U25 | 15-70374-001 | Latch, Octal Shockey (74LS374) 11-50001-332 |3.3K Resistor Sip Pack U26 |15-10001-001 | RAM 16K x1 Dynamic (4116) 11-50001-332 |3.3K Resistor Sip Pack 26-00001-016 | Socket DIP 16 Pin for U26 11-50001-332 |3.3K Resistor Sip Pack U27 | 15-10001-001 | RAM 16K x1 Dynamic (4116) 25-00001-014 | Connector, 14 Pin .156 Center 26-00001-016 | Socket DIP 16 Pin for U27 25-00002-014 | Connector, 14 Pin .156 Center U28 |15-10001-001 | RAM 16K x1 Dynamic (4116) 25-00001-001 | Connector, 50 Pin Header Vertical 26-00001-016 | Socket DIP 16 Pin for U28 25-00001-001 | Connector, 50 Pin Header Vertical U29 | 15-10001-001 | RAM 16K x1 Dynamic (4116) 25-00002-002 | Connector, 2 Pin .156 Center 26-00001-016 | Socket DIP 16 Pin for U29 25-00021-002 | Connector .1 Center for W1 U30 | 15-10001-001 | RAM 16K x1 Dynamic (4116) 26-00007-001 | Shorting Pin 26-00001-016 | Socket DIP 16 Pin for U30
| 132-00001-001 | |P.C.B. Video Processor Board | U31 | 15-10001-001 | RAM 16K x1 Dynamic (4116) |
15-20245-001 | Bus Transiciever, Octal (74LS245) 26-00001-016 | Socket DIP 16 Pin for U31
| 15-20245-001 | |Bus Transiciever, Octal (74LS245) | U32 | 15-10001-001 | RAM 16K x1 Dynamic (4116) |
15-10003-001 [Ram 1K x 4 NMOS Static (2114) 26-00001-016 | Socket DIP 16 Pin for U32 '26-00001-018 |Socket DIP 18 Pin for U3 33 |15-10001-001 | RAM 16K x1 Dynamic (4116) 15-10003-001 [Ram 1K x 4 NMOS Static (2114) 26-00001-016 | Socket DIP 16 Pin for U33 126-00001-018 [Socket DIP 18 Pin for U4 U34 |15-20374-001 | Latch, Octal (74LS374)
| 15-20157-001 | [Multiplexer Quad 2-Input (74LS157) | U35 |15-20153-001 | Multiplexer, Dual 4-Input (74LS153) |
115-20157-001 | Multiplexer Quad 2-Input (74LS157) U36 |15-20074-001 | Flip Flop Dual-D (74LS74)
| u7 | _[15-20074-001 | [Flip Flop, Dual D (74LS74) | U37 | 15-20008-001 | Quad, 2-Input and (74808) |
| U8 | [15-20032-001 | Quad 2 Input or (74LS32) | U38 | 15-70113-001 | Flip Flop JK Schottky (74LS113) | |
| Ug | _[15-20032-001 | Quad 2 Input or (74LS32) | U39 | 15-20004-001 | Inverter, HEX (74LS04) |
U10 |15-10001-001_ | RAM 16K x 1 Dynamic (4116) 40 | 15-30017-001 | Buffer/Driver, HEX (7417) 26-00001-016 |Socket DIP 16 Pin for U10 41 [15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-016 | Socket DIP 16 Pin for U41
VIDEO PROCESSOR
TATO | TANTO
| SYM | PART NO. | DESCRIPTION | SYM | |PART NO. | DESCRIPTION |
U42 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U81_ |15-20157-001 | Multiplexer Quad 2-Input (74LS157)
| t | 26-00001-016 | Socket DIP 16 Pin for U42 | U82 | |15-00002-001 | Microprocessor 68A09E |
U43 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-040 | Socket DIP 40 Pin for U82 26-00001-016 | Socket DIP 16 Pin for U43 U83 |15-20244-001 | Octal, Buffer (74LS244) U44 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U84 }15-20244-001 | Octal, Buffer (74LS244)
| 26-00001-016 | Socket DIP 16 Pin for U44 | U85 | |15-10002-001 | |RAM 1K x 4 CMOS Static (6514) |
U45 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-018 | Socket DIP 18 Pin for U85
| 26-00001-016 | Socket DIP 16 Pin for U45 | [ae | 15-10002-001 | |RAM 1K x 4 CMOS Static (6514) |
U46 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) 126-00001-018 | Sockei DIP 18 Pin for U86 26-00001-016 | Socket DIP 16 Pin for U46 U87 |15-20139-001 | Decoder Dual 1 of 4 (74LS139) U47 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U88 |15-20032-001 | Quad 2-Input of (74LS32) | 26-00001-016 | Socket DIP 16 Pin for U47 89 |15-20074-001 | Flip Flop, Duai-D (74LS74) U48 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U90 |15-20004-001 | Inverter, HEX (74LS04) 26-00001-016 | Socket DIP 16 Pin for U48 U91 }15-20374-001 | Latch, Octal (74LS374) U49 | 15-20032-001 | Quad 2-Input or (74LS32) U92 |15-20374-001 | Latch, Octal (74LS374) U50 | 15-20086-001 | Quad 2-Input Exclusive or (74LS86) |_uss 115-20374-001 | Latch, Octal (74LS374) U51 | 15-20086-001 | Quad 2-Input Exclusive or (74LS86) U94 |15-20374-001 | Latch, Octal (7415374) U52 | 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) U95 [15-20299-001 | Shift Register 8 Bit (74LS299) U53 | 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) U96 }15-20299-001 | Shift Register 8 Bit (74LS299) U54 | 15-20153-001 | Multiplexer, Dual 4-Input (7415153) U97 |15-20244-001 | Buffer, Octal (74LS244) U55 | 15-20157-001 | Multiplexer, Quad 2-Input (74LS157) U98 |15-20244-001 | Buffer, Octal (74LS244) U56 | 15-10008-001 | RAM 1K x 4 HMOS Static (2148) U99 |15-20138-001 | Decoder, 1 of 8 (74LS138) 26-00001-018 | Socket DIP 18 Pin for U56 | U100}15-40000-001 | Quad 2-Anput NOR (74C00) US7 | 15-10008-001 | RAM 1K x 4 HMOS Static (2148) U101]15-20008-001 | Quad 2-Input AND (74LS08) 26-00001-018 | Socket DIP 18 Pin for U57 U102|15-20010-001 | Triple 3-Input AND (74LS10) U58 | 15-30017-001 | Buffer/Driver, HEX (7417) U103}15-20000-001 | Quad 2-Input NAND (74LS00) U59 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U104/15-20157-001 | Multiplexer Quad 2-Input (74LS157) U60 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U105]15-20299-001 | Shift Register 8 Bit (74LS299) U61 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U106]15-20299-001 | Shift Register 8 Bit (74LS299) U62 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U107/15-20299-001 | Shift Register 8 Bit (74LS299) U63 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U108/15-20299-001 | Shift Register 8 Bit (74LS299) U64 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U109|15-20299-001 | Shift Register 8 Bit (74LS299) U65 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U110}15-20299-001 | Shift Register 8 Bit (741299) U66 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U67 | 15-20032-001 | Quad 2-Input or (74LS32) U68 | 15-20244-001 | Octal Buffer (74LS244) U69 | 15-20245-001 | BUS Transciever, Octal (7415245) U70 | 15-20374-001 | Latch, Octal (74LS374) U71 | 15-20374-001 | Latch, Octal (74LS374) U72 | 15-20374-001 | Latch, Octal (74LS374) U73 | 15-20157-001 | Multiplexer Quad 2-Input (74LS157) U74 | 15-201 zal Multiplexer Quad 2-Input (74LS157) U75 | 15-20245-001 BUS Transciever, Octal (74LS245) U76 | 15-20273-001 Register 8 Bit (74LS273) U77 | 15-20373-001 Latch, Octal (74LS373) 15-20373-001 Latch, Octal (74LS373) 15-20373-001 Latch, Octal (74LS373) U80 } 15-20373-001 Latch, Octal (74LS373)
DATA/SOUND PROCESSOR COMPONENT LAYOUT
| rer | : | = |
Pm) eee Teawe tg [yaazvs ¢[ masons [ Bey Gk EERE) aa
o . Gl <
| mah) (wee | ae | eaters | d |
icra] < een
ial rx]
| Ls | . | 4 | . |
[ eaaso #8 wit WE yaeseet ([74esene rea
irsz3}
| (ee 8 _ | os 5209 #8 | eer | ds |
- “s
| Ba | | esses | {e | eet | 4 oy] _ |
+ + ——— = FA +
s %
wa [eva] + 7008 amazon +4 2 ifs
wa zea Ce] r
Sy r ce |_| oe cz Cea] [o33) Lee] Cea 1s] er ir] a ar [<3] [OE] we fern rez) a ED a
DATA/SOUND PROCESSOR
| TAITO | TAITO | | |
SYM | PART NO. DESCRIPTION SYM | PART NO. DESCRIPTION
| At | 11-00001-473 | Resistor 47K YW +5% | FB5 | 17-00001-001 | Ferrite Bead | ||
| R2__| | 11-00001-322 | Resistor 3.3K %4W +5% | FB8_ | 17-00001-001 | Ferrite Bead | ||
| R3 | 11-00001-332 | Resistor 3.3K ¥4W +5% | FB9 | }17-00001-001 | Ferrite Bead | | |
R4 | 11-00001-332 | Resistor 3300 OHM 'Y4W +5% FB10 | 17-00001-001 | Ferrite Bead
| RS | | 11-00091-472 | Resistor 4.7K Y4W +5% | FB11 | 17-00001-001 | Ferrite Bead |
R6 | 11-00001-103 | Resistor 4.7K %4W +5% FB13 | 17-00001-001 | Ferrite Bead R7 | 11-00001-103 | Resistor 10K YW +5% FB14 |17-00001-001 | Ferrite Bead
| R8 | 11-00001-332 | Resistor 3.3K OHM YW +5% | FB15 | |17-00001-001 | Ferrite Bead |
RQ | 11-60001-502 | Pot, P.C. Mount 5K FB16 }17-00001-001 | Ferrite Bead R10 | 11-00001-473 | Resistor 47K 4W +5% FB17 | 17-00001-001 | Ferrite Bead [R11 | 11-00001-473 | Resistor 47K %W +5% FB18 | 17-00001-001 | Ferrite Bead [R12 | 11-00001-332 | Resistor 3.3K “MW +5% FB19 | 17-00001-001 | Ferrite Bead R13 | 11-00001-332 | Resistor 3.3K %4W +5% | F820 | 17-00001-001 | Ferrite Bead
| R14 | 11-00001-332 | Resistor 3.3K %4W +5% | C1 | | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead |
R15 | 11-00001-332 | Resistor 3.3K YaW +5% C2 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R16 | 11-00001-332 | Resistor 3.3K “UW +5% C3 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R17 | 11-00001-332 | Resistor 3300 OHM %4W +5% C4 =| 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead
| R18 | 11-00001-124 | Resistor 120K %4W +5% | C5 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead | | |
R19 } 11-00001-472 | Resistor 4.7K ¥4W +5% C6 =| 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R20 | 11-00001-221 | Resistor 220 OHM %W +5% | C7 | 12-20001-107 | Capacitor Electrolytic 100uf 16V
| R21 | 11-00001-221 | Resistor 220 CHM 4W +5% | C8 | | 12-20001-107 | Capacitor Electrolytic 100uf 16V |
R22 | 11-00001-332 | Resistor 3.3K 4W +5% C9 | 12-20001-107 | Capacitor Electrolytic 100uf 16V R24 | 11-00001-182 | Resistor 1.8K %W +5% C10 | 12-20001-107 Capacitor Electrolytic 100uf 16V R25 | 11-60001-104 | POT, P.C. Mount 100K C11 | 12-20001-107 | Capacitor Electrolytic 100uf 16V } R26 | 11-00001-103 | Resistor 10K %W +5% C42 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead | R27 | 11-00001-103 | Resistor 10K %4W +5% C13 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead
| R28 | 11-00001-223 | Resistor 22K %W +5% | C14 | {12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead | | |
R29 | 11-00001-562 | Resistor 5.6K ¥4W +5% C15 ea Capacitor Ceramic .1uf 50V Axial Lead
| R30_| | 11-00001-332 | Resistor 3.3K %4W +5% | C16 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead | |
| R31_| | 11-00001-020 | Resistor 2.2 OHM %4W +5% | ta | 12-10002-104 | Capacitor Ceramic .1ui 50V Axial Lead |
R32_ | 11-00001-010 | Resistor 1 OHM %W +5% C18 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead
| R33_| | 11-00001-020 | Resistor 2.2 OHM %4W +5% | C19 | 12-10003-470 | Capacitor 47pf 10% NPO Axial Lead |
R34 | 11-00001-010 | Resistor 1 OHM %W +5% C20 | 12-20001-105 | Capacitor Electrolytic tuf R35 | 11-00001-102 | Resistor 1.0K OHM YW +5% C21 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead R36_ | 11-00001-332 | Resistor 3.3K %4W +5% C22 | 12-20001-807 | Capacitor Electrolytic 800uf, 16V
| R37_| | 11-00001-152 | Resistor 1.5K %4W +5% | C23 | 12-20001-807 | Capacitor Electrolytic 800uf, 16V |
R388 | 11-00001-222 | Resistor 2.2K YW +5% C24 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead, R39 | 11-00001-221 | Resistor 220 OHM %4W +5% C25 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R40 | 11-00001-332 | Resistor 3.3K YW +5% C26 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R41 | 11-00001-562 | Resistor 5.6K %4W +5% C27 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R42 | 11-00001-223 | Resistor 22K %4W +5% C28 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead! R43. | 11-00001-103 | Resistor 10K %4W +5% C30 | 12-10001-471 | Capaciter Ceramic 470pf 50V 10% Axial Lead R44 | 11-00001-103 | Resistor 10K YW +5% C31 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead 11-00001-103 | Resistor 10K %4W +5% C32 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead 11-00001-472 | Resistor 4.7K Y4W +5% | c33 | 42-10002-104 | Capacitor Ceramic .1ut 50V Axial Lead 17-00001-001 | Ferrite Bead C34 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead FB2 | 17-00001-001 | Ferrite Bead C35 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead FB3 | 17-00001-001 | Ferrite Bead C36 | 12-10002-104 | Capacitor Ceramic .1ut 50V Axial Lead FB4 | 17-00001-001 | Ferrite Bead 1
DATA/SOUND PROCESSOR
TAITO TAITO SYM | PART NO. DESCRIPTION ‘SYM | PART NO. DESCRIPTION
| C37_| | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead | TP3 | 59-00021-001 | Test Point |
C38 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead TP4 | 59-00021-001 | Test Point C39 | 12-10001-123 | Capacitor Ceramic .012 50V Axial Lead TPS | 59-00021-001 | Test Point C40 | 12-10001-183 | Capacitor Ceramic .018 50V Axial Lead TP6 | 59-00021-001 | Test Point C41 | 12-10004-103 | Capacitor Ceramic .O1uf 50V Axial Lead TP7 | 59-00021-001 | Test Point C42 | 12-10001-332 | Capacitor Ceramic .0033uf 50V Axial Lead TP8 | 59-00021-001 | Test Point 12-10001-153 | Capacitor Ceramic .015uf 50V Axial Lead TP9 | 59-00021-001 | Test Point C44 | 12-10001-563 | Capacitor Ceramic .056uf 50V Axial Lead TP10 | 59-00021-001 | Test Point C45 | 12-10003-100 | Capacitor 10pf NPO Axial Lead TP11 | 59-00021-001 | Test Point C46 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead RP1 | 11-50001-332 | Resistor Sip Pack 3.3K C47 | 12-20001-105 | Capacitor Electrolytic 1uf Axial Lead RP2 | 11-50001-332 | Resistor Sip Pack 3.3K C48 | 12-20001-105 | Capacitor Electrolytic 1uf Axial Lead RP3 | 11-50001-471 | Resistor Sip Pack 47K C49 | 12-10001-471 | Capacitor Ceramic 470uf 50V Axial Lead RP4 | 11-50001-471 | Resistor Sip Pack 47K C50 | 12-10001-471 | Capacitor Ceramic 470pf 50V Axial Lead RP5 | 11-50001-103 | Resistor Sip Pack 10K C51 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead RP6 | 11-50001-332 | Resistor Sip Pack 3.3K
| C52_| | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead | U1 | 15-20244-001 | Octal Buffer (7415244) |
C53_ | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead U2 | 15-00002-001 | Microprocessor 68A09E C54 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead 26-00001-040 | Socket 40P DiP-For 68AO9E C55 | 12-20001-105 } Capacitor Electrolytic tuf U3 | 15-20244-001 | Octal Buffer (74LS244) Capacitor Ceramic .1uf SOV Axial Lead U4 | 15-20244-001 | Octal Buffer (7418244) C57 | 12-20001-477 | Capacitor Electrolytic 470uf, 16V U5 | 15-00007-001 | Microprocessor 6802 C58 | 12-20001-477 | Capacitor Electrolytic 470uf, 16V 26-00001-040 | Socket 40P DIP for 6802 C59 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U6 | 15-20244-001 | Octal Buffer (74LS244) C60 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U7 | 15-00004-002 | Parallel 1/0 6821 C61 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U8 | 15-00004-002 | Parallel 1/0 6821 C62 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U9 | 15-20245-001 | BUS Tranciever, Octal (74LS245) C63 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U10 | 15-20244-001 | Octal Buffer (74LS244) C64 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead U11 | 15-20245-001 | BUS Tranciever, Octal (74LS245) C65 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U12 | 15-20244-001 | Octal Buffer (74LS244) C66 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U13 | 15-50001-001 | Digital to Analog Converter 8 Bit (1408) C67 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U14 | 15-20032-001 | Quad 2-Input or (74LS32) 668 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead U15 | 15-10003-001 | RAM 1K x 4 NMOS Static (2114) C69 | 12-10002-104 | Capacitor Ceramic . 1uf SOV Axial Lead 26-00001-018 | Socket 18P DIP for 2114 C70 | 12-10002-104 | Capacitor Ceramic . 1uf 50V Axial Lead U16 | 15-10003-001 | RAM 1K x 4 NMOS Static (2114) C71_ | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 26-00001-018 | Socket 18P DIP for 2114 C72 | 12-10003-101 | Capacitor 100pf 10% NPO Axial Lead U17 | 15-20138-001 | Decoder 1 of 8 (74LS138) C73 | 12-10003-221 | Capacitor 220pf 10% NPO Axial Lead U18 | 15-50003-001 | Quad OP AMP LM324 C74 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U19 | 15-60004-001 | Speech Synthesis TMS5200 C75 | 12-20001-105 | Capacitor Electrolytic 1uf 26-00001-028 | Socket 28P DIP for TMS5200 C76 | 12-20001-105 | Capacitor Electrolytic 1uf U20 | 15-00004-001 | Parallel 1/0 68A21 C77 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U21 | 15-60002-001 | Line Driver (MC 1488) C78 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U22 | 15-00005-002 | Serial 1/0 68A50 C79 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 26-00001-024 | Socket 24P DIP for 68A50 C80 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U23 | 15-20004-001 | Inverter, HEX (74LS04) C81 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U24 | 15-44066-001 | Quad Analog Multiplexer (4066) C83 | 12-10003-100 | Capacitor 10pf NPO Axial Lead U25 | 15-60001-001 | Line Receiver (MC1489)
| TP1 | {59-00021-001 } Test Point | U26 | 15-20161-001 | Counter 4-Bit Presettable (74LS161) |
| TP2 | |59-00021-001 | Test Point | U27 | 15-20092-001 | Counter Divide By Twelve (74LS92) |
U28 | 15-44066-001 | Quad Analog Multiplexer (4066)
DATA/SOUND PROCESSOR
TAITO SYM | PART NO. DESCRIPTION U29 | 15-50002-001 | Audio Amplifier (2002) 30-00001-001 | Heatsink to 220 U30_| 15-50002-001 | Audio Amplifier (2002) 30-00001-001 | Heatsink to 220 SW1 | 29-00001-001 | Switch, DIP 4 Pole Y1 | 19-00002-001 | Crystal 7.3728 MHZ : Q1 | 14-23904-001 | Transistor NPN, Silcon 2N3904 J 25-00002-004 | Comrecior 14 PIN Locking J5 | 25-00001-001 | Connector Header 50 PIN J6 | 25-00001-001 | Connector Header 50 PIN J7 | 25-00002-005 | Connector 5 PIN Locking J8 25-00002-005 | Connector 5 PIN Locking J9 | 25-00003-001 | Connector RS232
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ROM/V/0 P.C. ASSEMBLY
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | SYM; PART NO. | DESCRIPTION |
| Ri_| | 11-00001-562 | Resistor 5.6K, 4W +5% | R51 | 11-00001-471 | |Resistor 470 OHM Y4W +5% |
R2_ | 11-00001-471 | Resistor 470 OHM %4W +5% R52 | 11-00001-562 | Resistor 5.6K, 4W +5%
| R3__| | 11-00001-471 | Resistor 470 OHM YW +5% | R53 | 11-00001-562 | Resistor 5.6K, “W +5% |
| R4 | 11-00001-471 | Resistor 470 OHM %4W +5% | R54 | 11-00001-471 | |Resistor 470 OHM Y4W +5% |
| R5 | 11-00001-471 | Resistor 470 OHM %4W +5% | R55 | 11-00001-471 | {Resistor 470 OHM Y4W +5% |
| R6 | 11-00001-471 | Resistor 470 OHM %W +5% | R56 | 11-00001-471 | [Resistor 470 OHM YW =5% |
| R7_| | 11-00001-471 | Resistor 470 OHM %4W +5% | R57 | 11-00001-471 | Resistor 470 OHM %4W =5% |
R8 | 11-00001-471 | Resistor 470 OHM “W +5% R58 | 11-00001-471 | Resistor 470 OHM YW +5% RQ | 11-00001-471 | Resistor 470 OHM YW +5% R59 | 11-00001-471 | Resistor 470 OHM YaW +5%
| Ri0 | 11-00001-471 | Resistor 470 OHM “wW +5% | R60 | 11-00001-471 | {Resistor 470 OHM Y4W +5% |
Rit | 11-00001-471 | Resistor 470 OHM YaW +5% R61 | 11-00001-471 | Resistor 470 OHM %4W +5%
| R12 | 11-00001-471 | Resistor 470 OHM thW +5% | R62 | 11-00001-471 | |Resistor 470 OHM %W +5% |
R13 | 11-00001-471 | Resistor 470 OHM 4W +5% R63 | 11-00001-471 | Resistor 470 OHM %W «5% |
| R14 | 11-00001-471 | Resistor 470 OHM %W +5% | C1 | | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead |
R15 | 11-00001-471 | Resistor 470 OHM %4W 5% | C2 | 12-10002-104 |Capacitor Ceramic .1uf Axial Lead
| R16 | 11-00001-471 | Resistor 470 OHM %4W +5% | C3__| | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead |
R17 | 11-00001-471 | Resistor 470 OHM YW +5% C4 =| 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R18 | 11-00001-471 | Resistor 470 OHM YW +5% | C5_| | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | |
| R19 | 11-00001-471 | Resistor 470 OHM YW +5% | C6 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | “| |
R20 | 11-00001-562 | Resistor 5.6K, 4W +5% C7 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R21 | 11-00001-562 | Resistor 5.6K, %4W +5% C8 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R22 | 11-00001-562 | Resistor 5.6K, %4W +5% | C9 | | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | |
| R23_| | 11-00001-562 | Resistor 5.6K, %W +5% | C10 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead |
| R24 | 11-00001-562 | Resistor 5.6K, %W +5% | C11 | 12-10001-471 | |Capacitor Ceramic 470pt Axial Lead |
| R25 | 11-00001-862 | Resistor 5.6K, %W +5% C12 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R26 | 11-00001-562 | Resistor 5.6K, %W +5% C13 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R27 | 11-00001-562 | Resistor 5.6K, %4W +5% | C15 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R28 | 11-00001-471 | Resistor 470 CHM %4W +5% | C16 | 12-10001-471 | |Rapacitor Ceramic 470pf Axial Lead |
| R29 | 11-00001-471 | Resistor 470 OHM VW +5% | \c17 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead |
R30_ | 11-00001-471 | Resistor 470 OHM YW +5% Ci8 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R31_| | 11-00001-471 | Resistor 470 OHM “4W +5% | C19 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead |
R32 | 11-00001-471 | Resistor 470 OHM VW «5% C20 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R33 | 11-00001-471 | Resistor 470 OHM %4W +5% C21 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R34 | 11-00001-471 | Resistor 470 OHM YW +5% C22 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R35 | 11-00001-471 | Resistor 470 OHM YW +5% €23 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead [R36 | 11-00001-471 |Resistor 470 OHM YW +5% C24 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R37 | 11-00001-471 | Resistor 470 OHM Y4W +5% C25 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R38 | 11-00001-471 | Resistor 470 OHM %4W +5% C26 | 12-10001-471 | Capacitor Ceramic 470pt Axial Lead
| R39_} | 11-00001-471 | Resistor 470 OHM YW +5% | C27 _| 12-10002-104 | Capacitor Ceramic .1uf Axial Lead |
R40 ZI 11-00001-562 | Resistor 5.6K, %4W +5% |c28 | 12-10002-104 Capacitor Ceramic .1uf Axial Lead R41 | 11-00001-562 | Resistor 5.6K, %4W +5% C29 | 12-10002-104 | Capacitor Ceramic .iuf Axial Lead R42 | 11-00001-562 | Resistor 5.6K, ¥4W +5% C30 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R43 | 11-00001-562 | Resistor 5.6K, 4W +5% C31 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R44 | 11-00001-471 | Resistor 470 OHM YW +5% C32 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead
| R45 | 11-00001-471 | Resistor 470 OHM %W +5% | €33_| | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead |
R46 | 11-00001-471 | Resistor 470 OHM %W +5% C34 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead [Re | 11-00001-471 | Resistor 470 OHM YW +5% 035, 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R49 | 11-00001-471 | Resistor 470 OHM YW +5% €36_| 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R50_| 11-00001-471 | Resistor 470 OHM %4W +5%
ROM/V/0 P.C. ASSEMBLY
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | SYM | PART NO. | DESCRIPTION |
| C37 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | C85 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
C38 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C86 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| C39 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | C87 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| C40 | 12-10001-471 [ Capacitor Ceramic 470pf Axial Lead | C88 | |12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
C41 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C89 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C42 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C90 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C43 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C91 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| C44 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | C92 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
C45 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB1 | 17-00001-001 | Ferrite Bead
| C46 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB2 | 17-00001-001 | |Ferrite Bead |
C47 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB3_ | 17-00001-001 | Ferrite Bead
| C48 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB4 | |17-00001-001 | |Ferrite Bead |
| C49 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB5 | |17-00001-001 | jFerrite Bead |
C50 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB6 | 17-00001-001 | Ferrite Bead
| C51 | 12-10001-471 | Capacitor Ceramic 470pf Axia! Lead | FB7 | |17-00001-001 | |Ferrite Bead |
C52 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB8 | 17-00001-001 | Ferrite Bead C53 | 12-10002-104 -luf Axial Lead FB9 | 17-00001-001 | Ferrite Bead C54 | 12-10002-104 lic .1uf Axial Lead FB10 | 17-00001-001 | Ferrite Bead
| C55 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead | FB11 | 17-00001-001 | |Ferrite Bead |
| C56 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead | FB12 | 17-00001-001 | |Ferrite Bead |
C57 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB13 | 17-00001-001 | Ferrite Bead C58 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB14 | 17-00001-001 | Ferrite Bead
| C59 | 12-10002-104 | Capacitor Ceramic .tuf Axial Lead | FB15 | 17-00001-001 | |Ferrite Bead |
| C60 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead | FB16 | 17-00001-001 | |Ferrite Bead |
C61 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB17 | 17-00001-001 | Ferrite Beag C62 | 12-10001-471 | Capacitor Ceramic 479pf Axial Lead FB18 | 17-00001-001 | Ferrite Bead C63 | 12-10001-471 | Capacitor Ceramic 470pt Axial Lead FB19 | 17-00001-001 | Ferrite Bead
| C64 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB20 | 17-00001-001 | |Ferrite Bead |
| C65 | 12-10007-471 | Capacitor Ceramic 470pf Axial Lead | FB21 | 17-00001-001 | |Ferrite Bead |
C66 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB23 | 17-00001-001 | Ferrite Bead C67 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB24 } 17-00001-001 | Ferrite Bead C68 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB25 | 17-00001-001 | Ferrite Bead
| c6g { 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | | | FB26 | 17-00001-001 | Ferrite Bead |
C70 | 12-20001-107 | Capacitor Electrolytic 100uf FB27 | 17-00001-001 | Ferrite Bead C71 | 12-10001-471 | Capicitor Ceramic 470pf Axial Lead FB28 | 17-00001-001 | Ferrite Bead C72 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB29 | 17-00001-001 | Ferrite Bead C73 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB30 | 17-00001-001 | Ferrite Bead C74 | 12-10002-104 | Capacitor Ceramic . tut Axial Lead FB31 | 17-00001-001 | Ferrite Bead C75 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB32 | 17-00001-001 | Ferrite Bead C76 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB33 | 17-00001-001 | Ferrite Bead
| C77 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead | | | FB34 | 17-00001-001 | Ferrite Bead |
C78 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB35 | 17-00001-001 | Ferrite Bead C79 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB36 | 17-00001-001 | Ferrite Bead C80 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB37 | 17-00001-001 | Ferrite Bead C81 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB38 | 17-00001-001 | Ferrite Bead C82 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB39 | 17-00001-001 | Ferrite Bead C83 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB40 | 17-00001-001 | Ferrite Bead
| {84 | 42-10001-471 | Capacitor Ceramic 470pf Axial Lead | _| | FB41 | 17-00001-001 | Ferrite Bead |
ROM//0 P.C. ASSEMBLY
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | SYM | PART NO. | DESCRIPTION |
| FB42 | 17-00001-001 | Ferrite Bead | U6 | E-PROM “ELECTRIC YOYO"'™ |
FB43 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U6
| FB44 | 17-00001-001 | Ferrite Bead | u7 | E-PROM “ELECTRIC YOYO"™ |
FB45 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U7
| FB46 | 17-00001-001 | Ferrite Bead | U8 | E-PROM “ELECTRIC YOYO"™ |
FB47 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U8
| FB48 | 17-00001-001 | Ferrite Bead | ug | E-PROM “ELECTRIC YOYO"™ |
FB49 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U9
| FB50 | 17-00001-001 | Ferrite Bead | U10 | E-PROM “ELECTRIC YOYO"'™ |
FB51 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U10 FB52 | 17-00001-001 | Ferrite Bead U11_ | 15-00004-001 | Paralell 1/0 68A21
| FB53 |17-00001-001 | |Ferrite Bead | U12 | E-PROM “ELECTRIC YOYO"'™ |
| D1 | | 13-14001-001 | Diode IN4001 | 26-00001-024 | Socket 24 Pin Dip for U12 | |
| D2 | 13-14001-001 | Diode IN4001 | U13 | E-PROM ‘ELECTRIC YOYO"'™ |
D3 | 13-14001-001 | Diode 1N4001 26-00001-024 | Socket 24 Pin Dip for U13
| D4 | 13-14001-001 | Diode IN4001 | U14 | E-PROM “ELECTRIC YOYO"'™ |
D5 | 13-14001-001 | Diode 1N4001 26-00001-024 | Socket 24 Pin Dip for U14
| D6 | 13-14001-001 | Diode 1N4001 | U15 | E-PROM “ELECTRIC YOYO"'™ | |
| D7 | __|13-14001-001 | Diode 1N4001 | 26-00001-024 | Socket 24P Dip Used For E-PROM | |
| D8 | _|13-14001-001 | Diode IN4001 | U16 | E-PROM “ELECTRIC YOYO"™ |
| D9 | 13-14001-001 | |Diode IN4001 | 26-00001-024 | Socket 24 Pin Dip for U16 | |
| D10 | 13-14001-001 | |Diode IN4001 | UI7 | E-PROM “ELECTRIC YOYO"™ |
| D11 | 13-14001-001 | |Diode IN4001 | | | 26-00001-024 | Socket 24 Pin Dip for U17 |
| D12 | 13-14001-001 | Diode IN4001 | U18 | E-PROM “ELECTRIC YOYO"™ | |
| Q1 | 14-00001-001 | |Transistor NPN Darlington TIP120 | 26-00001-024 | Socket 24 Pin Dip for U18 | |
| Q2 | 14-00001-001 | |Transistor NPN Darlington TIP120 | u19 | E-PROM “ELECTRIC YOYO"'™ |
| Q3 | 14-00001-001 | |Transistor NPN Darlington TIP120 | 26-00001-024 | Socket 24 Pin Dip for U19 | |
| Q4 | 14-00001-001 | |Transistor NPN Darlington TIP120 | U20 | 15-00004-001 | Paralell 1/0 68A21 | |
| Q5 | 14-00001-001 | |Transistor NPN Darlington TIP120 | U21 | 15-20138-001 | Decoder 1 of 8 (138) | |
| Q6 | 14-00001-001 | |Transistor NPN Darlington TIP120 | U22 | 26-00002-016 |ROM Select |
Q7 =} 14-00001-001 |Transistor NPN Darlington TIP120 26-00001-014 | Socket 24P Dip for U22
| Q8 | —_|14-00001-001 | Transistor NPN Darlington TIP120 | U23_ | 15-20004-001 | Inverter, HEX (74LS04) | |
| Q9 | Not Used | 24 | Not Used |
| Q10 | 14-00001-001 | Transistor NPN Darlington TIP120 | U25 | Not Used | |
| Q11 | 14-00061-001 | |Transistor NPN Darlington TIP120 | U26 | Not Used |
| Q12 | 14-00001-001 | Transistor NPN Darlington TIP120 | U27 | E-PROM “ELECTRIC YOYO"™ |
| U1 | | 26-00002-016 |ROM Select | 26-00001-014 |Socket 14P Dip for U27 |
26-00001-014 {Socket 14P Dip, for U1 U28 | 15-20138-081 | Decoder 1 of 8 (138)
| U2 | 15-20138-001 | |Decoder 1 of 8 (138) | U29 | ROM Select |
| U3 | E-PROM “ELECTRIC YOYO"'™ | 26-00001-014 |Socket 14P Dip Used For ROM Select | |
| 26-00001-024 |Socket 24 Pin Dip for U3 | U30_| | 15-00004-001 | |Paralell 1/0 6821 |
| U4 | E-PROM “ELECTRIC YOYO"'™ | J3__| | 25-00001-001 | Connector Header SOPIN |
| 26-00001-024 |Socket 24 Pin Dip for U4 | J5 | 25-00001-001 | |Connector Header SOPIN | |
| U5 | E-PROM ‘ELECTRIC YOYO"'™ | J6 | 25-00001-001 | Connector Header SOPIN |
26-00001-024 |Socket 24 Pin Dip for US J11 | 25-00002-014 |Connector 14 Pin Header .156 Center J15 | 25-00002-014 |Connector 14 Pin Header .156 Center J16 | 25-00002-014 {Connector 14 Pin Header .156 Center J17 | 25-00002-014 | Connector 14 Pin Header .156 Center
o% xy ¢ \/ ¢ VJ a +. ‘YY \J a ¢ \/ x) x) (\X iY a (y \/ y \/ AN + \/ + J a x) ) %4 ¢. tX az» (XX xxx /o sc} ]d<} Jae] fac] INSIST IST IS] @Q tr a~ x ov, a 0% ix XX XX XXX XXX XX LL 3uNDld LNOAWV] GUVO HOSSIIOUd NIOI
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
I VIDEO PROCESSOR PCB 08-00001-001
COIN DOOR
CONTROL, PANEL 08-00003-00r
Efaiisertso 1@ PR LLILEEE! ll com_Do0R Eom free =
pov — EE, Ey Seaver : senvee ; so so-00 ' r wey i 1
t j
q Beam tenis MASQUE = ae i ile: ~ h ri POWER
SUPPLY
L pce can “fe 08-00007-001 DATA /SOUND ” PCB 08-00002-001
TUb-be | -de waO)/\4+ A+
[pies 2 n Tear SINK ASSEMBLY
NOTES
NOTES
sap
TAITO AMERICA CORPORATION 1256 Estes Avenue, Elk Grove Village, IL 60007 Telephone (312) 981-1000 Telex 25-3290