CATHODE RAY TOMES

Super Pac-Man General Information and Troubleshooting Procedures (April 1983)

Super Pac-Man (Namco, 1982) · Troubleshooting · 58 pages · 25 sections · original scan

Page 1

il, 1983 Game Nos. 316 & 317 puma scampi 's

General Information and Troubleshooting Procedures

(silly MIDWAY MFG. Co.

PHONE: PHONE:

(312) 451-9200 10601 WEST BELMONT AVENUE TOLL FREE I TELEX 72-1596 FRANKLIN tetas 60131 800-323-7182 Form 00368-8304

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment generates. uses. and can radiate radio frequency energy and if not and used in accordance with the instructions manual. may cause interference to radio communications. It has been tested and tound to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated in a commerical environment..Operation of this equipment in a residential area 1s likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

Oo esomee BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF S! LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

Cally |MIDWAY

OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 IHinois Only 1-800-942-0497

© COPYRIGHT MCMLXXxXIII BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

TABLE OF CONTENTS

INTRODUCTION OPTION SWITCH SETTING GAME OPERATION TROUBLE SHOOTING CONTROL INPUTS & OPTION SWITCHES .... SYSTEM TIMING CPU BOARD BUS STRUCTURE AUDIO CIRCUITRY VIDEO BOARD BUS STRUCTURE VIDEO RAM CIRCUITS COLOR RAM POWER CHASSIS & POWER SUPPLY WIRING DIAGRAM POWER CHASSIS DIAGRAM POWER SUPPLY SCHEMATIC CPU BOARD SCHEMATIC VIDEO BOARD SCHEMATIC SERVICE BULLETINS 7 FUNCTION CHART .... 2.0.0... ee cece eee te crete eterna nets

Page 4

Super Pac-Man

IMPORTANT NOTE

DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and li of this manual completely. it will not take more than a few minutes and it may be very helpful.

I. Introduction

SUPER PAC-MAN is a one or a two player game. There are two models: the “UPRIGHT” and “COCK- TAL TABLE”. When the two player mode is selected on the Upright model, the players take turns at the conirols to guide their player through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn, When playing this game, you are in complete control of SUPER PAC-MAN. He will go wherever you tell him to. And he just loves to eat all the different maze objects (APPLES, BANANAS, DOUGHNUTS, HAM- BURGERS, etc.). However, he doesn't like the four ghosts, BLINKY (red), PINKY (pink), INKY (tur quoise), and CLYDE (amber) because they feel the same way about him as he does about the maze objects. BLINKY, PINKY, INKY, and CLYDE are four VERY SMART ghosts. They move very fast and seem to have a sixth sense which always lets them know exactly where SUPER PAC-MAN is in the maze. They never give up in their pursuit of him. One of their favorite tricks is to divide and try to trap him between them. You really have to keep an eye on them. But SUPER PAC-MAN can turn the tables on these four ghosts for short periods of time during each maze. All he has to do is let them get fairly close in their pursuit of him and then eat one of the POWER DOTS that every maze has in it. When this happens, it causes the four ghosts to turn blue with fright no matter where, they are in the maze. This is because they know that when he eats a POWER DOT it gives SUPER PAC-MAN the ability to eliminate them. However, he can ONLY eliminate them for as long as they are blue.

The ghosts will only stay blue for a few seconds after SUPER PAC-MAN eats a POWER DOT. But they do give a warning BEFORE they turn back to their original colors — they start to flash.

As your skill level increases, the four ghosts speed up their pursuit of SUPER PAC-MAN and they stay blue for shorter and shorter periods of time after he eats a POWER DOT until, in the VERY high number mazes, they do not turn blue at all.

Bonus players (this is switch selectable) can be awarded to you as you reach or pass certain preselected point values. The assigned point values for all items that can be eaten are as listed in Figure 1-1.

Page 5

Major Features

A major new feature of your SUPER PAC-MAN game is that there are two SUPER POWER DOTS in each maze that, when eaten, will cause your PAC-MAN to turn intoa SUPER PAC-MAN. SUPER PAC-MAN can go anywhere within the maze and eat anything that can be eaten. Nothing can stop him.

OBJECT EATEN

APPLES BANANAS . DOUGHNUTS . HAMBURGERS 222272...

POWER DOTS. SUPER POWER DOTS 1ST GHOST . 2ND GHOST. 3RD GHOST. 4TH GHOST. Game Objective

The object of the game is to HAVE FUN and survive as long as possible while constantly improving your skills, eating as many maze objects as you can, and eliminating as many ghosts as possible. As you do this, each following maze will be harder and harder to complete.

POINT VALUE

...10 POINTS EACH . 20 POINTS EACH . 30 POINTS EACH ...40 POINTS EACH VARIABLE 50 TO 160 POINTS EACH ... 50 POINTS EACH 100 POINTS EACH 200 POINTS EACH 200 POINTS 400 POINTS . 800 POINTS --.1600 POINTS

Figure 1-1 Assigned Point Values

Page 6

INSTALLATION

  • Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) U Humidity: Not over 95% relative O Space required: Upright 25” x 33” (63 x 84cm) Cocktail 32” x 22” (81 x 55cm) O Game height: Upright 68” (170cm) Cocktail 29" (73cm)
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. if the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the Proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
  • Interlock and power ON/OFF switches: See Figure 2-1. O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright models). O When any access door is opened, the interlock switch installed there turns off ali power to the game. O Check each interlock switch for proper operation. Aiter checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem trom your distributor and/or your service man, plug the game into your A.C. wall outiet. The game ON/OFF switches for both models are jocated as shown in Figure 2-1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. Ajter the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the garne with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-2.

Figure 2-2 Interlock Switch Operation

SELF-TEST Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game’s speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

Page 7

GAME VOLUME ADJUSTMENT CONTROL See Figure 2-3. The game volume control pot is located on the game CPU board assembly. There is only one pot. For adjustment, it may be reached through the rear access door on the Upright models. On the Cocktail Table models, you will have to open the table top to reach it. To make the sounds louder, turn the pot in a clockwise direction (~~ _). To make the sounds less loud, turn the pot in a counterclockwise direction ( #7 ~ ).

OPTION SWITCH SETTINGS To change the option switch settings, you DO NOT. have to take the Main Game CPU Board out of the

VOLUME ADJUSTMENT

oy

LOUDER game. They can be easily reached through the rear access door on the Upright models. On the Cocktail Table model, you do have to open the table top to reach them. When changing any options, ALWAYS put the game into the Self-Test mode, make your changes, check the results on the monitor screen, take the game out of the Self-Test mode, and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The option switch settings and what they will make. the game do are shown in Figure 2-4. See Figure 2-3 for option switch locations.

OPTION SWITCH SW-2 (LOC. 5B)

OPTION SWITCH SW-3 (LOC. 5E)

Figure 2-3 Game Volume Adjustment Control & Option Switch Location

Page 8

SUPER PAC-MAN

OPTION SWITCH SETTINGS

DIP SWITCH SW-2 AT LOCATION 5B

DIFFICULTY LEVEL SETTINGS — “R1” IS THE EASIEST AND “RB” IS THE MOST DIFFICULT

SW#1 SW#2 SW#3 SW#4 SWHS SWHE SWH7 SWH8 RANK “RO”"—STANDARD LEVEL OF DIFFICULTY OFF OFF OFF OFF

RANK “R1”—EASIEST LEVEL OF DIFFICULTY ON OFF OFF OFF

RANK “R2” OFF ON OFF OFF

RANK “R23”ONON OFF OFF

RANK “R4” OFF OFF ON OFF RANK “RS” ON OFF ON OFF RANK “R6”—GRADUATED LEVELS OF DIFFICULTY | OFF ON ON OFF

RANK “R7”ONONON OFF

*RANK “R8”—FACTORY SETTING OFF OFF OFF ON RANK “RQ” ON OFF OFF ON RANK “RA” OFF ON OFF ON

RANK “RB"—HARDEST LEVEL OF DIFFICULTYONON OFF ON_|

RANK “RC”—EASIEST AUTO DIFFICULTY SETTING | OFF OFF ON ON

RANK “RD”ON OFF ONON
RANK “RE”OFF ONONON
RANK “RF”—HARDEST AUTO DIFFICULTY SETTING]ONONON

SOUND

SW#H SW#2 SWH3 SWH4 SWH5 SWHs SWH7 SWEB *SOUND OFF NO SOUND ON

SCREEN

SWH1 SW#2 SWH3 SWH4 SWHS SWHS SW47 SWHB *NORMAL OPERATION OFF FREEZE VIDEO ON

*INDICATES FACTORY RECOMMENDED SETTINGS PART NUMBER MO51-00316-C012

Figure 2-4 Option Switch Settings

Page 9

SUPER PAC-MAN

OPTION SWITCH SETTINGS

DIP SWITCH SW-3 AT LOCATION 5E

COINS PER CREDIT — COIN SWITCH 1

SW#2 SW#3 SWH4 SWH5 SWHE SWH7 SWH8

*1 COIN1 CREDITOFF OFF
1 COIN2 CREDITSOFF OFF
1 COIN3 CREDITSON OFF
1 COIN6 CREDITSON OFF
1 COIN7 CREDITSOFF ON
2 COINS1 CREDITOFF ON
2COINS3CREDITSONON
3 COINS1 CREDITONON

BONUS SUPER PAC-MEN AWARDED AT THE FOLLOWING POINT VALUES:

BEGAN WITH 1, BEGAN WITH 2.0R 3 SUPER PAC-MEN 5 SUPER PAC-MEN SWiH1 SW#2 SWH3 SWH4 SWHS SWHE SWH7 SWH8

*tst S P-M300001st S P-M30000
2ndSP-M1006002ndSP-M — 100000OFF OFF OFF
1st S P-M1st S P-M30000
2nd S P-M800002nd S P-M120000
1st SP-Mist S P-M40000
2nd S P-M1200002nd S P-M420000OFF ON OFF
1st S P-M30000ist S P-M30000
AND EVERY80000AND EVERY100000CNON OFF
1st S P-M300001st S P-M40000
AND EVERY = 100000AND EVERY = 120000OFF OFF ON

1st S P-M 30000 AND EVERY — 120000 1st SP-MP — 100000

ONLY ONLY

1S P-M AT300001S P-M AT40000OFF ONON

NO BONUS SHIPS GIVEN WITH THIS SETTING ON ON ON

DETERMINES NUMBER OF SUPER PAC-MEN PLAYER BEGINS GAME WITH:

SW#1 SW#2 SW#3 SW#4 SW#S SWHE SWH7 SWHB *3 SUPER PAC-MEN OFF OFF 1 SUPER PAC-MAN ON OFF 2 SUPER PAC-MEN OFF ON 5 SUPER PAC-MEN ON ON

*INDICATES FACTORY RECOMMENDED SETTINGS PART NUMBER MO51-00316-C012

Figure 2-4 Option Switch Settings (cont.)

Page 10

Ill. Game Operation

SUPER PAC-MAN is a one or a two player game with acolor T.V. monitor. The game gives a display which has all the parts shown below.

PLAYER 1 SCORE

PAC-MAN (SHOWN SUPER SIZE)

RESERVE PAC-MAN The game has five possibile modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE/ INITIAL, and SELF-TEST.

PLAYER 2 SCORE

ENERGIZER DOT

i> GATE KEY

SUPER POWER DOT

RACK IDENTIFIER

Identification of “On Screen” Graphics During Play

SELF-TEST MODE

The Self-Test mode is a special mode for checking the game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test will cause it to erase any CREDITS on the game from its memory.

You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on. When this is done the game will react as follows:

  • First, you will see random moving multicolored patterns on the screen.
  • Immediately following this, a rightside up test display is shown on the monitor screen. This will remain until you set the Self-Test switch back to the “OFF” position. This test display is shown at right. RAM OK ROM 0K

io %«

ast COIN

COIN

PACHAN RANK SOUND 00 CREDIT

CREDIT 2ND

Self-Test — Menue

Page 11
  • if a bad ROM or RAM‘chip is found by the game’s internal check system during the Self-Test, the game indicates this to you by showing the location code of the bad chip(s) on the SCREEN. The following table translates the chip location codes into the actual position on the game's P.C. Boards.

RAM TEST INDICATIONS AND THEIR MEANINGS

INDICATION

RAM OK RAM 1 RAM 2 RAM 3 RAM 4 RAM 5 RAM 6 RAM 7 MEANING CHIP LOCATION

NO RAM IS OUT OF ORDER RAM 1 on VIDEO PCB is no good 2E RAM 2 on VIDEO PCB is no good 2H RAM 3 on VIDEO PCB is no good 2K RAM 4 on VIDEO PCB is no good 2d RAM 5 on C P U PCB is no good 3K RAM 6 on C P U PCB is no good 3L RAM 7 on C P U PCB is no good 2D

ROM TEST INDICATIONS AND THEIR MEANINGS

INDICATION

ROM OK ROM 1 ROM 2 ROM 3 MEANING CHIP LOCATION

NO ROM IS OUT OF ORDER ROM 1 on CP U PCB is no good 1c ROM 2 on C P U PCB is no good 1B ROM 3 on C P U PCB is no good 1K

VO TEST INDICATIONS AND THEIR MEANINGS INDICATION

VO OK MEANING

NO BIT IS OUT OF ORDER CHIP LOCATION

vo1 BIT C P U 1 is out of order 4F 1/02 BIT C P U 2is out of order ac

  • To check your game function switches and buttons (coin counter switches, TEST CREDIT button, 1 PLAYER and 2 PLAYER buttons): activate each one while the game is in the Self-Test mode. You should hear a game sound for each activation. If you do not hear it, the switch/button is either not working, miswired, or disconnected. Check it out thoroughly.
  • RANK is a difficulty level setting with “R1” being the easiest and “RB” being the most difficult level of play. “RC” through “RF” are AUTO difficulty level settings with “RC” being the easiest and “RF” the hardest setting. In “AUTO” the game measures the player's skill level and AUTOMATICALLY gets harder as his/her skill level improves.
  • When finished with the Self-Test mode, slide the Self-Test switch back to the “OFF” position. OA cross hatch pattern appears on the monitor screen for about 2 seconds. C If you wish to keep this test pattern on the monitor screen for further use, slide Self-Test switch back to the “ON” position after the cross hatch appears and before it disappears. G When finished with the cross hatch pattern, set the Self-Test switch to the “OFF” position. 0 Normal game functions will now return to the monitor screen.
Page 12

ATTRACT MODE

  • The Attract mode starts: O Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) O After a Self-Test has been completed. (Performing a Self-Test sets the credits in the game’s memory to zero “O”.)

BALLY. MIDDAY 1980, 1982

crept 0 2 Attract Mode Display 1

ne dich te wo 3

2S 23922

POHER

sipEeR @

© BALLY MIDWAY 1980, 198s

CREDET O— bi

Attract Mode Display 2 Q After a play has been finished and there are no more credits left in the game’s memory. O In the Attract mode, the game will give the following displays centered on the monitor screen:

POWER

suPER @

© GALLY MIDWAY 1980, 1982

GREDIT 6 bad

Attract Mode Display 3

POWER

SUPER on © BALLY MIDWAY L980, 1982 _

-2 CREDIT © Attract Mode Display 4

Page 13

BALLY. MIDHAY 1960, 1952

Attract Mode Display 5

a

SOOOD

30000

S0C06 36000.

CREDIT 0

Attract Mode Display 6 i

ici eas elomentpuidiee

Attract Mode Display 7

No matter where ihe game is in the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for. It will hold this display on the monitor screen until the “1 PLAYER” or “2 PLAYER” start button is pushed.

Page 14

PUSH START BUTTON

i PLAYER ONLY

30000 PT

IST BONUS @ For

2ND BONUS @& FOR 100000 PT

é} BALLY MIDWAY 1980, 1982

CREDIT 4

Ready to Play Mode Display 1

READY-TO-PLAY MODE

  • The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game.
  • The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed.
  • Inthe Ready-To-Play mode, the game will give one of the above displays centered on the monitor screen.
  • If no START button is pressed, the game will hold this display on the screen indefinitely.

PLAY MODE

  • The Play mode begins when the “1 PLAYER” or the “2 PLAYER’ start button is pressed. “STAGE 1" “10 PTS” is displayed and then “PLAYER __ READY!” is displayed below the “GHOST HOUSE” on the screen.
  • The Play mode ends when your fast SUPER PAC- MAN has been eliminated. When this happens, “PLAYER —_ GAME OVER’ is written across the center of the monitor screen (below the “GHOST HOUSE”).
  • The game consists of a single maze with side exits. The items that your SUPER PAC-MAN wants to eat are located in maze corridors with locked doors at every possible entrance to them. You must direct your PAC-MAN to eat the KEYS PUSH START BUTTON

4 OR 2 PLAVERS

PF BONUS @ FOR 30000 prs’

2ND BONUS € FOR 100000 PIS¢

& BALLY MIDHAY 1980, toR2

CREDIT &

Ready to Play Mode Display 2

positioned around the maze in order to gain access“to these sealed corridors. The only other way he Can get at the food he wants to eat is to eat the KEY that opens the door to one of the two SUPER POWER DOTS in each maze and then eat that SUPER POWER DOT. When he does this, your PAC-MAN grows to SUPER size and can munch his way through all the locked doors in the maze. YOU can give YOUR Pac-Man SUPER SPEED while he is SUPER size by pressing the SUPER SPEED button on the control panel. He will now move through the maze at a much faster pace. However, you will find that he is harder to steer when he is traveling at this SUPER SPEED and you will also notice that he stays SUPER size for amuch shorter period of time when traveling at SUPER SPEED.

  • At the beginning of each game, SUPER PAC-MAN appears right below the center of the “GHOST HOUSE” while the four ghosts appear at the “GHOST HOUSE”. BLINKY appears outside the doors and PINKY, INKY, and CLYDE appear inside the “GHOST HOUSE”.
  • When play begins, BLINKY (who'd: love to eliminate him) immediately begins looking for SUPER PAC-MAN (who immediately begins eating KEYS just as fast as he can). As time passes, PINKY, INKY, and CLYDE (who'd also love to eliminate him) leave the “GHOST HOUSE” one ata time and begin looking for SUPER PAC-MAN — who is still busily eating KEYS and maze food just as fast as YOU can steer him to them.
Page 15

But with ail four ghosts chasing him, it is not as easy to eat the KEYS and maze food (without being eliminated by a ghost) as it was earlier in the game. And BLINKY, PINKY, INKY, and CLYDE are four VERY SMART ghosts. For instance, they will divide up two, three, or four ways to try to trap SUPER PAC-MAN between them, in a corner, or even in one of the tunnels. You've really got to watch them! It seems like they always have some sneaky new trick up their sheets. However, if they get too close, SUPER PAC-MAN can always eat one of the flashing POWER DOTS. When this happens, it causes all four ghosts to turn blue with fright no matter where they are in the maze. This is because they know that when he eats a POWER DOT it gives SUPER PAC-MAN the ability to eliminate them. But, he can ONLY eliminate them for as long as they are blue. And they will only stay blue for a short period of time. But the ghosts do give a warning BEFORE they turn back to their original colors — they start to flash. When SUPER PAC-MAN eliminates a blue ghost, its point value appears on the monitor screen at the place where the ghost was eliminated while at the same time being added to your score, and the ghost disappears — ali except for its eyes. The eyes go back to the “GHOST HOUSE” where they get another body of their original color. This done, they leave the “GHOST HOUSE” again and take up their pursuit of SUPER PAC-MAN once more. When he eats the last item of any particular maze: all movement stops immediately, the maze flashes and disappears. Next, the game displays “STAGE __"“___ PTS” and the next maze appears. All the players are in the new maze when it appears. The words “PLAYER __ READY!” are also there — right below the “GHOST HOUSE”. After a second or two passes, the words “PLAYER __ READY!” disappear and play begins.

You MUST eat all the food in any particular maze in order to advance to the next one.

The maze identifier symbols appear at the bottom edge of the monitor screen. As your skill level increases, the four ghosts speed up their pursuit of your SUPER PAC-MAN and they stay blue for shorter and shorter periods of time after he eats a POWER DOT until, in the high number mazes, they do not turn biue at all. Bonus players (this is switch selectable) can be awarded to you as you reach or pass certain preselected point values. The assigned point values for all items that can be eaten are as listed in Figure 1-1. When one of the ghosts happen io eliminate one of your SUPER PAC-MEN, assuming you have at feast one remaining in reserve, the maze disappears. Next, the game displays “STAGE __” “___ PTS” and the maze re-appears. All the players are in the new maze when it reappears. The words “PLAYER __ READY!" are also there — right below the “GHOST HOUSE”. After a second or two passes, the words “PLAYER __ READY!” disappear and play begins anew. When one of the ghosts eliminates your LAST SUPER PAC-MAN, the words “GAME OVER” are displayed below the “GHOST HOUSE”, your score is displayed under “1 UP”, and in addition, if your score was the highest on this game to date, it will also be displayed under “HIGH SCORE” at the top center of the monitor screen and go into the HIGH SCORE/INITIAL MODE. If your score was NOT the highest but was still one of the best five scores to date, the game will then also go into the HIGH SCORE/INITIAL MODE. After this the game will then either go into the Ready-To-Play mode (if there are still credits left in its memory) or into the Attract mode (if there are no more credits left in its memory). If your score was not high enough to cause the game to go into the HIGH SCORE/INITIAL MODE, it will then either go into the Ready-To- Play mode (if there are still credits left in its memory) or into the Attract mode (if there are no more credits left in its memory). Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.

49890

SCORE as 9890

High Score/Initial Mode

Page 16

TWO PLAYER OPERATION The Upright and Cocktail Table models both have two player operation. In the two player mode, the rules of play are the same as in the single piayer mode. There are some additional rules, however.

  • In the Upright model, the players must take turns at the controls.
  • In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When it is not your turn, your set of conirols will have NO effect on the game.)
  • Your turn lasts until one of the ghosts eliminates your SUPER PAC-MAN. Ai this point, the game will do one of several things depending on whether or not the eliminated SUPER PAC-MAN was your last or if you still have others remaining in reserve.

SUPER PAC-MAN ELIMINATED — OTHERS RE- MAINING IN RESERVE

0 The chase stops. O Next, the game displays “STAGE __” “__. PTS”, the screen display changes tothe screen display of the other player, it displays “PLAYER __ READY!” under the “GHOST HOUSE" at the same time one of the other player's reserve SUPER PAC-MAN appears. O After a second or two passes, the words “PLAYER —— READY!” disappear and play begins for the other player.

SUPER PAC-MAN ELIMINATED — NO OTHERS REMAINING IN RESERVE G Game displays the words “PLAYER ONE” or “PLAYER TWO” “GAME OVER" below the “GHOST HOUSE”. C Your final score is displayed under “1 UP” or “2 UP”, depending upon which player you were. In addition, if your score was the highest on this game to date, it will alsobe displayed under “HIGH SCORE” at the top center of the monitor screen and go into the HIGH SCORE/INITIAL MODE. If your score was NOT the highest but was still one of the best five scores to date, the game will then also go into the HIGH SCORE/INITIAL MODE. After this the game will display “STAGE __” and “__ PTS”. The other player's maze appears along with the words “PLAYER _— READY!” under the GHOST HOUSE. After a few moments, the words “PLAYER __ READY!” disappear and play begins for the other player. : If your score was not high enough to cause the game to go into the HIGH SCORE/INITIAL MODE, it will then display “STAGE __” and “___ PTS". The other player’s maze appears along with the words “PLAYER __ READY!" under the GHOST HOUSE. After a few moments, the words “PLAYER __ READY!" disappear and play begins for the other player. D After the last player’s LAST SUPER PAC-MAN has been eliminated, if his score was not high enough to cause the game to go into the HiGH SCORE/ INITIAL MODE, it will then either go into the Ready-To-Piay mode (if there are still credits left in its memory) or into the Attract mode (if there are no more credits left in its memory).

Page 17

NOTES

This space is provided for personal notes

Page 18

Harness Component Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a compiex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and répair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is stillno game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When notactuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 19

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring. until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to Operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it’s OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of inputit is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 20

NOTES

This space is provided for personal notes

Page 21

NOTES

This space is provided for persona! notes

Page 22

CONTROL INPUTS AND OPTION SWITCHES

As in all Midway games the player controls use normally open switches with one pole of each

switch connected to common or logic ground. The other pole of each switch is connected to the input

circuits on the CPU board via the wiring harness.

Examine the PLYR1-LEFT (player one move left) input on J2-2. Pin number 2 of connector J2

will normally read +5 volts. When the player one joystick is moved left pin number 2 of J2 should drop to 0 volts. If it does not drop to O volts there is a problem in the switch or wiring. If J2-2 responds correctly but the Pac-Man will not move left, the problem is on the CPU board.

Following the PLYR1-LEFT line the first component is a .O1MF capacitor, C77. This capacitor is connected between the PLYR1-LEFT line and earth ground to filter out any noise or static discharge

that might enter the line. If C77 is missing or broken, the circuit will still operate but the line will lack static protection. If this capacitor is shorted the PLYR1-LEFT line will read O volts and the Pac-Man

will move leit automatically.

The 1K ohm resistor in package RM15 pulls the line up to +5 volts. If this resistor is missing or

broken the line will read 0 volts.

The 2.2K ohm resistor in package RM14 is used to protect the 56XX custom input component

at location 4F If this resistor is broken or missing, pin number 25 of the 56XX will read 0 volts and the

Pac-Man will move left automatically.

Capacitor C21 is used to debounce the PLYR1-LEFT control line. When a control switch is first closed its contacts bounce and might send a series of pulses to the 56XX at 4F A capacitor connected between the control line and logic ground will discharge upon switch closure and reduce the bouncing

to a single smooth pulse. If the debounce capacitor is broken or missing the circuit will operate but the

56XX will see numerous pulses for a single switch closure. A missing debounce capacitor on line J2-7

or J2-8 could mean numerous credits for a single coin. If the debounce capacitor is shorted, pin 25 of

the 56XX will read O volts and the Pac-Man wil! move left automatically.

After discussing the RRCC network on the PLYR1-LEFT line one can see that if the line reads

O volts the Pac-Man will move left automatically (unless the 56Xx is faulty). If the line reads correctly up

to pin 25 of 4F but the Pac-Man does not respond properly, the 56XX is probably faulty.

lt is not always noticeable when there is a bent pin or missing signal at the 56XX. If pins 1 and 3 are removed from the circuit the game will appear to function normally. In most cases however a bent pin or missing signal to 4F will cause the game to be stuck in self test and the symptom “!/O-1” will

appear on the second line of the test.

Page 23

Another 56XX custom input chip is located at position 4C. This second device receives data

from the DIP SW packages SW2 and SW3 at positions 5B and 5E. Note that data from SWS is multi-

plexed thru the 74L$157 at 4E before reaching the 56XX.

Multiplexing allows the eight lines of data from SWS to share only four lines between 4E and the 56XX. There are eight inputs on a 74LS157 (four “A” inputs and four “B” inputs) and four outputs

(1Y, 2Y, 3Y and 4Y). When the select line on pin 1 is low, data on the “A’ inputs will appear on the “Y” outputs. When the select line is high, the “B” inputs will appear on the “Y” outputs. In this manner

either input 1A or 1B can be transferred to output 1Y depending on which input the 56XX needs to

examine. The strobe line on pin 15 of 4E must be low for the 74LS157 to operate.

The eight lines of data from SW2 are pulled-up to +5 volts thru 4.7K ohm resistors in resistor package RM1. When a switch in SW2 is OFF, the corresponding input on the 56XX will read +5 volts. When the switch is ON, the input will read 0 volts. If the pull-up resistor on a SW2 line is faulty or missing the line will read O volts and the 56XX will not recognize when that switch is off.

Data from the self test switch enters the CPU board on J2-14 and data determining whether the

board is used as an upright or table model comes in on J2-15. When J2-15 is high the board responds

as an upright game. When J2-15 is low the board will respond as a table model and flip the picture

upside down for the second player. In an upright cabinet J2-15 is not used so the line reads +5 volts

because of the pull-up resistor R20. In a table cabinet an extra wire in the harness connects J2-15 to common or logic ground so the line reads 0 volts. Both lines J2-14 and J2-15 are conditioned by RRCC networks before reaching the 56XX. A

faulty RRCC component on either line will cause the line to read 0 volts. The 2H*, 4 reset and VBLANK signals feed pins 1, 2 and 4 of both 56XX components. The eight output pins (9, 10, 11, 12, 34, 35, 36, 37) on both 4C and 4F are also connected in parallel. Note that

outputs 9, 10, 11 and 12 feed a 74LS157 multiplexer at position 3E while outputs 12, 34, 35, 36 and 37

feed the 16XX custom bus controller at position 4B. A faulty signal,-bent pin or broken trace on any of

these eight output lines will cause the game to be stuck in self test and to display “I/O-1". Also if the signals on pins 5 and 6 of either 4C or 4F are missing the game will be stuck in self test. Switches 1, 2 and 3 of SWS at location 5E determine pricing. Switches 4, 5 and 6 of SW3

determine the scores required to earn bonus Super Pac-Men. Note that the score required to earn the

bonus will differ depending on whether the game is set to start with 1, 2 or 3 Super Pac-Men or 5

Super Pac-Men. Switches 7 and 8 of SW3 set the number of Super Pac-Men the game will start with.

Page 24

SW? at location 5B is used to set the difficulty level of game play. There are twelve fixed levels

of difficulty and four automatic difficulty levels. Switch 7 of SW2 determines whether or not the game sounds will occur during the attract mode. Switch 8 is very useful for diagnosing the game. When switch 8 is turned ON the game play will freeze. The picture and sound will remain frozen as long as

switch 8 is ON.

A “rack test” is also available using switch 8 of SW2. To enter the “rack test” coin and start a game. Then just as the Super Pac-Man begins to move, turn switch 8 ON. Now each time the FAST (or

speed) button is pushed the next maze in the game sequence will appear on the screen. Using this

“rack test” option one can obtain any maze in the sequence without playing the game.

Data concerning the status of the player controls and option switches (SW2 and SW3) leaves

the 16XX custom bus controller from pins 7,8, 10, 11, 12 and 13. This data is then either stored in the

2114 RAM at 2D or passed thru the 74LS245 at 2E to the buffered main data bus. If any of these six outputs are missing or incorrect the game may be stuck in self test displaying “RAM 7” or “I/O-1".

So a “RAM 7” display in self test does not necessarily mean that the RAM at 2D is bad. As one can see

a faulty 16XX or bad D10 thru D14 line could be the problem. An incorrect signal on pins 1, 3, 4,5 and

6 of the 16XX will also cause the game to be stuck in self test displaying “RAM 7” or “I/O-1".

Outputs 9, 10, 11 and 12 of both 56XX components become the “B” inputs to a 74LS157 multi-

plexer at position 3E. The “Y” outputs of multiplexer 3E are used as address lines (A6, A7, A8 and AQ)

to the 2114 RAM at 2D. When the select line to 3E is low, BMAO thru BMAS from the buffered main

address bus appear at the address lines to RAM 2D. When the select line is high, outputs 9, 10, 11

and 12 of the S6XX components are used to address RAM 2D.

Page 25

NOTES

This space is provided for personal notes

Page 26

SYSTEM TIMING

System timing starts with the 18.432MHz crystal and the 74LS368 inverting buffer at position

4A. The signal from pin 11 of 4A is used to clock both flip-flops at position 3B. The 2Q output from pin

10 of 3B is inverted to become the 6MB, 6MSYNC and 6M (6 megahertz) signals. The 6M signal is

ORED with the 1H signal thru the 74LS32 at position 3C. Pin 8 of 3C is used to clock the flip-flop at

2A. Pin 9 of flip-flop 2A yields the Q signal which is used at pin 35 of microprocessor 1A and pin 34 of

microprocessor 1L.

In the Pac-Man and Ms. Pac-Man systems a chain of binary counters are used to divide the

6 megahertz signal to produce the H & V timing signals. In Super Pac-Man this is accomplished by two

07XX custom components at positions 1N on the CPU board and 2C on the video board.

The 07XX at position 1N on the CPU board outputs the equivalents of the H timing signals

from pins 2 thru 8. The 07XX on the video board outputs the equivalents of the V timing signals.

Starting with the 1H signal from pin 2 of the 07XX on the CPU board each pin up to pin 8 is

1/2 the frequency of the preceding pin. The 1H signal is 3MHz. The 2H signal is 1.5MHz and pin 4

(4H or A20) is 1/2 that frequency or .75MHz etc. The H timing signals are necessary to synchronize the microprocessor circuits. 2H is inverted and then used at pin 34 of microprocessor 1A. The 2H* signal from pin 11 of buffer 2H is used at pin

35 of microprocessor 1L. The outputs of the 07XX are also used to address RAMS 3K and 3L and to

control the 15XX custom component in the audio circuitry.

The outputs of the 07XX on the video board are processed thru an OOXX custom address

generator at position 2D. The outputs of the OOXX are used to address RAM 2E and are gated thru 15

1B and decoder 1C. Pins 12, 13, 14 and 15 of decorder 1C are used as EG (tri-state control) inputs to

the bus transceivers at 1E, 1H, 1J and 1K. Pins 3, 6, 8 and 11 of chip 1B are the CS signals to RAMS

2E, 2H, 2J and 2K. Addressing to RAMS 2H, 2U and 2K also requires the outputs from the OOXX.

MA17 thru MA20 are outputs from gates 1F and MA30 thru MA36 are outputs from the 04XX custom

address generator. Note the timing signals controlling gates 1F and the 04Xx.

Page 27

NOTES

This space is provided for personal notes

Page 28

BUS STRUCTURE (CPU BOARD)

Microprocessor 1A is master to microprocessor 1L. Both microprocessors are supported by

their own PAL, ROM and bus control circuitry. Timing on pins 34 and 35 of 1A and 1L synchronizes the

operation of both microprocessors. Besides interfacing with their related circuits some communication

must occur between the microprocessors themselves.

The MAIN address bus from microprocessor 1A services the program ROMS, PAL 2B and

decoder 2C and is then buffered thru 74LS367 components at positions 1E, 1H and 2H to become the

buffered MAIN address bus (BMAO thru BMA15).

The SOUND address bus (SAO thru SA15) from microprocessor 1L services the SOUND ROMS and PAL 1M. SAO thru SAQ supply the A inputs to multiplexers 3F 3H and 3J. Note that the B inputs to the multiplexers are supplied by BMAO thru BMAQ from the MAIN address bus. The outputs

of the multiplexers will coincide with either the BMA bus or the SOUND address bus depending on

the condition of the 1H signal or the outputs will be held in tri-state by the 2H signal.

The 2H signal on pin 15 of the multiplexers controls the Y outputs. When the 2H signal is low the A or B inputs will appear at RAMS 3K and 3L. When the 2H signal is high the Y outputs are disabled to allow a third source of addressing to the RAMS. The 07XX at position 1N and the 15XX at position 3N provide the third address bus. Pins 4, 5, 6, 7 and 8 of the 07XX and pin 6 of the 15XX

supply address lines A20 and A25 after being buffered thru a 74LS367 at position 2N.

The 1H signal on pin 1 of the multiplexers is used to select the A inputs or the B inputs to

appear on the Y outputs. When the 1H signal is high the BMA bus will service RAMS 3K and 3L. When

the 1H signal is low the SOUND address bus will service the RAMS.

The 1H signal is twice as fast as the 2H signal so while the 2H signal is low the 1H signal will

have time to select the A inputs and the B inputs and both microprocessors will have a chance to address

RAMS 3K and 3L. While the 2H signal is high the multiplexer outputs are disabled and addressing from

the O7XX and the 15XX will service the RAMS. Note that address lines A20 thru A23 are decoded by a

74LS259 at position 2M to provide the reset and interrupt signals for the two microprocessor circuits

and that the buffered MAIN address bus is sent thru a ribbon cable to the video board.

The eight data lines on pins 24 thru 31 of the G8AO9E microprocessor are bidirectional. Data

can flow into or out of the microprocessor on these eight \ines. Of course data can only move along these

lines in one direction at a time. Only one signal can have access to a data line at any moment in time.

The 68AO9E at position 1A can read from program ROM 1B or 1C (1D is not used) when the

2H* signal on pin 22 of the ROMS is low and the R/W signal at pin 6 of the 74LS138 at 2C is high.

Page 29

When the R/W signal from pin 32 of microprocessor 1A is high the decoder at position 2C will decode

the MA13, MA14 and MA15 address lines. Depending on the status of these address lines one of the

decoder outputs will be driven low while the other decoder outputs remain high.

If decoder output Y6 or Y7 is driven low the corresponding ROM will have access to the MAIN

data bus. The decoder at 2C assures that only one program ROM can have access to the data bus at

any moment in time.

The MAIN data bus from microprocessor 1A is buffered thru a bidirectional bus transceiver at

position 1F The direction that data passes thru the 74LS245 is controlled by the R/W signal on pin

number 1. Note that this R/W signal is from pin 19 of the PAL at 2B and should not be confused with

the R/W signal from pin 32 of microprocessor 1A. The 74LS245 can be disabled by a high signal on

pin 19 to isolate the MAIN data bus from the buffered MAIN data bus (BMDO thru BMD7). When the [oO MAIN data bus and the BMD bus are isolated microprocessor 1A can communicate with the program ROMS and the BMD bus is free to interface with RAMS 3K, 3L and 3D and the buffered SOUND data bus.

The SOUND data bus from microprocessor 1L services SOUND ROM 1K and is buffered thru

a 74LS245 at position 2K to interface with RAMS 3K, 3L and the 15XX at 3N. The direction data passes thru 2K is controlled by the R/W signal from pin 32 of microprocessor 1L. The SOUND 2 signal controlling the EG pin on 2K comes from PAL 1M.

After the bidirectional bus transceiver at 2K, the buffered SOUND data bus (BSDO thru BSD7)

is tied directly to RAMS 3K, 3L and the 15XX. The BSD bus can communicate with the buffered MAIN

data bus thru the 74LS245 at position 2F

Itis the bidirectional bus transceiver at 2F that allows the two microprocessors to communicate

with one another. Chip 2F also allows both microprocessors to have access to RAMS 3K, 3L and 2D.

Bus transceivers 1F and 2F are both controlled by the R/W signal from PAL 2B so both will

pass data in the same direction (A inputs to B inputs or B inputs to A inputs) at the same time. The EG

(bus isolation control) signal to chip 1F comes from PAL 2B pin 12 but the EG to chip 2F is the SOUND

signal from pin 18 of PAL 2B so both transceivers will not necessarily be enabled at the same time.

Note another bidirectional bus transceiver at position 2E. Again the direction of data flow thru

2E will be the same as thru chips 1F and 2F because pin 1 of 2E is controlled by the R/W signal from

PAL 2B. The FBIT signal from PAL 2B controls the EG input of bus transceiver 2E.

Suppose that bus transceivers 1F. 2F and 2E are enabled by low signals on the EG inputs and

Page 30

that the R/W signal from PAL 2B is high. Data can now pass from the A inputs to the B inputs of each

bus transceiver. Data from RAM 2D could now pass thru chips 2E and 1F to microprocessor 1A or data

from the 16XX in the control input circuits could reach microprocessor 1A. If bus transceiver 2E is dis-

abled the buffered SOUND data bus can pass thru chips 2F and 1F to microprocessor 1A and RAMS

3K and 3L can be read by microprocessor 1A. Now suppose the R/W signal from PAL 2B is low so that data can pass from the B inputs to

the A inputs of the bus transceivers. The MAIN data bus could now pass thru chips 1F and 2E to

RAM 2D or thru chips 1F and 2F to either RAMS 3K and 3L or to the 74LS245 at position 2K and

microprocessor 1L.

Page 31

NOTES

This space is provided for personal notes

Page 32

AUDIO CIRCUITRY

The microprocessor at 1L, ROM 1K and the PAL at 1M are dedicated to the audio circuitry.

Timing and control signals for the 68AO9E microprocessor at 1L are not the same signals used for the

microprocessor at position 1A. The Q signal from the clocking circuit is buffered thru 2H for the E timing

input on pin 34 and the 2H* signal from pin 11 of buffer 2H is used as the Q timing input on pin 35. The RESET input on pin 37 of this microprocessor uses the SUBRESET signal from pin 10 of the

74LS259 at position 2M. The IRQ input on pin 3 is once again the Q output ofa flip-flop at 2J but here

the flip-flop is cleared by the INTON2 signal from pin 4 of the 74LS259 at 2M.

The PAL at 1M controls the CS (chip select) and OE (output enable) on ROM 1K. SRAMWR

(sound RAM write) is gated thru the 74LS08 at 4J to control R/W to RAMS 3K and 3L.

LTWR (latch write) is connected to pin 14 of the 74LS259 (8 bit addressable latch) at position

2M to enable this latch. Note that the INTON2 and SUBRESET signals which are critical for operation

of the microprocessor at 1L are outputs of this latch. At the same time, the microprocessor 1L and the

PAL at 1M must be operating properly to generate the LTWR signal which enables the latch. So we see

a loop between the microprocessor circuit in the audio system and the 74LS259 latch at position 2M.

Also the LATCH and SNDWR (sound write) signals controlling the PAL at 1M are outputs of the PAL at

2B in the main microprocessor circuit. The sound system microprocessor is subordinate to the main

microprocessor circuitry. So a failure at PAL 2B or in the main microprocessor circuits can disrupt the

entire audio system.

Data from ROM 1K can be bused directly to microprocessor 1L. To communicate with the

RAMS at 3K and 3L the sound data bus must pass thru a 74LS245 at position 2K. The bidirectional bus transceiver at 2K is enabled by the SOUND 2 signal from PAL 1M. Microprocessor 1L delivers a R/W signal to pin 1 of 2K. This R/W signal determines which direction data can pass thru the 74LS245.

Although the schematic shows a 64K ROM at 1K and a 32K ROM at 1J only position 1K is

used. If the 32K ROM used at 1K is faulty the game will be stuck in self test with the display ROM 3.

If the 2148 RAM at 3K is missing or faulty the game will display RAM 5 and if RAM 3L is faulty the game

will display RAM 6. Data on the A side of 2K is referred to as the “buffered sound data bus” (BSDO thru BSD7). Besides communicating with RAMS 3K and 3L the BSD bus controls the 15XX custom address generator

at position 3N. The 15XX might be considered the first component in the circuit that actually generates

the game sounds.

The 15XX uses some of the H timing signals, the BSD bus and 18.432MHz from the clock circuit to generate addressing for the PROM at position 3M. If pins 1, 2, 3 or 5 of the 15XX are not

Page 33

receiving the correct signal the self test will read O.K. but there will be either no sound or just hissing

and clicking thru the speaker. If pin 4 does not receive the correct signal the game will be stuck in self

test displaying RAM 5. If pins 6, 7 or 8 do not output the correct signal or if these signals do not reach

their destinations the self test will read O.K. but there will be no sound in the game mode. It has been

found that if a BSD line is removed from the 15XX or if the outputs from the 15XX do not reach the

PROM at 3M the game sounds will be present but distorted. Usually a missing BSD line or output from the 15XX will cause the game sounds to be faster or higher in frequency. The 4 bit nibble from pins 9, 10, 11 and 12 of PROM 3M is the data to be modified and then presented to the final audio amplifier at position 5N. This nibble supplies the 5D, 6D, 7D and 8D inputs

to the octal flip-flops at 4M and will appear on the 5Q, 6Q, 7Q and 8Q outputs when the SOUND ON

signal is high. After 4M, each of the four lines are assigned a value of resistance. Note that starting

with resistor R34 each resistor up to R37 is 1/2 the value of the preceding resistor. R35 is 1/2 the value

of R34. R36 is 1/2 the value of R35 and R37 is 1/2 the value of R36. After this “resistor ladder” all

four lines are shorted together. This circuit is commonly referred to as an “analog adding circuit”.

Because all four lines are tied together after the analog adding circuit we now have a single line of data. This single line of data can be passed thru any of the four electronic switches in package 4L.

Examine the bottom switch in the 4066 (quad bilateral switch package) at 4L. Data from the analog

adder circuit can enter pin 1 and exit pin 2 whenever pin 13 is high. Ifthe control pin 13 is low the switch

is open and data will not pass thru. The control signals on pins 13, 6, 5 and 12 of the 4066 are supplied

by BSDO thru BSD3 ai the 1Q, 2Q, 3Q and 4Q outputs of 4M.

After the bilateral switches we find another analog adding circuit (R22, R23, R24 and R25).

Again the four lines are tied together to form a single line of audio data. The line is pulled-up to +5 volts

by resistor R27 and held from logic ground by resistor R17 and capacitor C25. If capacitor C25 is shorted

the line will be pulled-down to 0 volts causing loss of all game sounds. Resistor R26 and VR1 (volume

control) can cause loss of all sounds if they are missing or faulty.

The MB3730 at position 5N amplifies the audio signal and sends two active lines to the speaker.

The MB3730 requires approximately +12 volts on pin 7. This +12 volts is only used for the audio circuit

so the game will operate properly without it except for the absence of the game sounds.

An easy way to check the MB3730 for amplification is to turn the volume control up all the way

and then to tap a finger on pin number 1. If the tapping can be heard thru the speaker the MB3730

is amplifying. Pins 5 and 6 are the outputs of the MB3730. If capacitors C27, C28 or C84, C85, C86 and C87 are faulty, sound or volume will be lost.

Page 34

NOTES

This space is provided for personal notes

Page 35

BUS STRUCTURE (Video Board)

The tri-state buffered MAIN address bus (BMAO thru BMA15) from microprocessor 1A on the

CPU board enters the video board thru connector P1 and the ribbon cable. The 07XX custorn com-

ponent at position 2C on the video board generates vertical timing signals which are sent to the OOXX

at 2D. The outputs from the OOXX are tri-state and tie in with the BMA signals so that either the BMA

bus or the vertical timing signals can address RAM 2E. When the FLIP signal on pin 27 of the O07XX

is high the picture will flip upside down for the second player in a table model game. The FLIP signal

is derived from the BMDO signal by a 74LS74 flip-flop at position 4A on the video board.

The combined BMA/vertical timing bus is also required by the 04XX custom component at

position 2F, the 74LS138 decoder at 1C and the 74LS32 OR gates at position 1F

The outputs from decoder 1C and ANDED thru a 74LS08 at 1B to provide the chip select

signals for RAMS 2H, 2 and 2K. MASO thru MA36 from the 04XX provide the low order addresses to RAMS 2H, 2J and 2K while MA17 thru MA20 from the OR gates at iF provide the high order addresses.

Note the numerous signals required by the 04XX.

The buffered MAIN data bus (BMDO thru BMD7) also enters the video board thru connector

P1 and the ribbon cable. The BMD bus is buffered thru bidirectional bus transceivers 1E, 1H, 1J and 1K

to provide four separate data buses on the video board.

Data bus “A” (D50 thru D57) from bus transceiver 1E services the 2K X 8 RAM at 2E and the

octal flip-flop packages at 1D and 4F The outputs from flip-flops 1D and 4F are used to address ROMS

in the final video stages.

Data bus “1” (D10 thru D17) from bus transceiver 1K services RAM 2K and the 12XX custom

component at position 3J. The 12XX is used to address the 8K X 8 character ROM at position 3F Data

bus “1” is also used as the preset inputs to binary counters 1M, 2M, 1N and 2N which address the video

RAMS 4M and 4N.

Data bus “2” (D20 thru D27) services RAM 2J and the 12XX custom component.

Data bus “3” (D30 thru D37) services RAM 2H and the 12XX custom component. 030 thru D35

is latched thru a 74LS378 at position 3K to address a ROM at 3L. D32 thru D37 is latched thru a

74LS278 at position 3H to provide addresses A8 thru A12 and “chip select” for character ROM 3F.

Each of the data buses (A’, “1”, “2” and “3”) on the video board has access to a 2K X 8 RAM

(RAMS 2E, 2H, 2U and 2K). Each of the four daia buses and their associated RAMS are used to address

character ROMS 3C or 3F

Page 36

Data bus “A’ is latched thru octal flip-flops at 1D to address character ROM 3C. Note that

addresses AO thru A3 of ROM 3C are supplied by the 1V, 2V, 4V and 4H signals on the inputs of XOR gates at 3B. When the FLIP signal on the XOR gate inputs is low, the V and H signals will pass thru unchanged. When the FLIP signal is high, the H and V signals will be inverted by the XOR gates. The XOR gates at 3B are being used as part-time inverters to flip the picture for the second player in table

model games.

The character ROM at 3C generates the maze image. If it is removed from the circuit the blue

maze lines and the pink gates will disappear from the picture. The game will play normally without ROM

3C and the characters will respond as if the maze is present but the maze will be invisible. The 8 bit

bus from 3C is loaded into the 11XX custom component at position 3D to be converted to serial form

and then passed to the final video circuits.

The 12XX custom component at position 3J receives data from buses “1”, “2” and “3” and con-

verts it to addresses A30 thru A35 which supply the AO, A1, A2, A5, A6 and A7 inputs of character

ROM 3F. The 2764 ROM shown at position 3E on the schematic is not used in Super Pac-Man.

182 thru D36 from data bus “3” is latched thru a 74LS278 at position 3H to supply the A8 thru

A12 address inputs of ROM 3F Output pins 8 and 11 of the XOR gates at 4H supply the A3 and A4

inputs to character ROM 3F. Note that the FLIP signal is used to control the 4H* and 8H* signais thru

the XOR gates so that address inputs A3 and A4 will be inverted when the picture is flipped. The

2H signal controls the OE (output enable) of ROM 3F and the CS (chip select) input is supplied by the

D40 signal from pin 12 of the 74L.S273 at 3H.

Character ROM 3F generates the moving characters and the keys. If ROM 3F is removed

from the circuit the game will play normally but Super Pac-Man, the ghosts and the keys will be square

blocks instead of defined images. The square blocks are referred to as the “window” or “hit zone” for

each character.

The 8 bit data buses from character ROMS 3C and 3F are loaded into the 11XX custom com-

ponent at position 3D. The 11XX converts the sixteen data lines from the character ROMS to four

lines of serial data. Pins 11 and 12 of the 11XX provide addresses AO and A? for the ROM at 4E while

pins 17 and 18 provide AO and A1 to the ROM at 3L. The signal from pin 3 of NAND gate 4B, the signal

from pin 3 of XOR gate 4H and the FLIP signal control the 11XX custom component.

Page 37

NOTES

This space is provided for personal notes

Page 38

VIDEO RAM CIRCUITS

The D2148 RAMS (1K X 4) at 4M and 4N store the images of Super Pac-Man, the ghosts and

the various fruits and maze symbols while they're being shifted around the screen. If either video RAM

is faulty the characters may have thin lines thru their bodies, their eyes may be the wrong size and color,

tiny dots might appear on the screen or thin lines might run from top to bottom across the entire screen.

The characters might be duplicated many times or shifted to the wrong position on the screen if these

RAMS are faulty. As one can see, a bad video RAM can cause numerous problems with the graphics

but the game will still coin and play thru the program.

To determine which video RAM is faulty use a wire connected to +5 volts and momentarily

force the RAM outputs high one at a time and observe the screen. IMPORTANT: If the output of an

integrated circuit is forced high or low for too long a period of time, the component may be damaged.

Cutting the RAM output pins will cause the same response as forcing them high without causing the

RAM to burn out.

In a good circuit each video RAM output will cause a change in some of the characters when

it is forced high or cut. In a faulty circuit, check each video RAM output to find the output that either

does nothing or eliminates the symptom when it is forced high.

Data bus “1” from bus transceiver 1K is used to preset the binary counters at positions 1M, 2M, 1N and 2N. Data on the A, B, C and D inputs of a 74LS161 binary counter will be transferred to the QA, QB, QC and QD outputs whenever the L (load) input is low, Data from bus “1” is loaded into the binary counts to set a starting address to video RAMS 4M and 4N when the HSET signal from pin 13

of buffers 3M and 3N forces the L inputs low. When the L inputs are high, the counters will increment the address to RAMS 4M and 4N by one count for each pulse on the CK inputs of the counters. Note

that the CK inputs are driven by the 6M signal from pin 11 of the 74LS368 at position 2B on the

video board.

|f an address line to the video RAMS is faulty thin vertical lines may appear thru the characters and keys or their images may be duplicated many times on the picture. An easy way to isolate the faulty

address line is to momentarily force each address line low with a jumper wire connected to logic ground

(0 voits). The faulty address line will usually cause no change on the picture when it is forced low.

Data bus “3" from bus transceiver 1H is latched thru a 74LS373 at position 3K to provide

D50 thru D55 which address a ROM at 3L. The four bit nibble from ROM 3L is buffered thru chip 3M

to tie in with the outputs of RAM 4M and thru chip 3N to the outputs of RAM 4N. Note that each of the

outputs from buffers 3M and 3N is pulled up to +5 volts thru either resistor pack RM1 or RM2.

Page 39

The four bit nibble from ROM 3L is also NANDED thru a 74LS20 at position 4J. Pin 6 of NAND

gate 4J is then NANDED with the OBJEN (object enable) and 6M signals to supply the 1A and 4B inputs to multiplexer 4K. The 6MB and HSYNC signals also supply inputs to multiplexer 4K. The outputs of chip 4K are used as WE (write enable) to RAMS 4M and 4N and as CL (clear) to the binary counters.

The four bits of data (DD10 thru DD13) from ROM 3L and RAM 4N provides word 2 to the

74LS298 at position 4L. DD20 thru DD23 from ROM 3L and RAM 4M provides word 1 to the 74LS298.

The 74LS298 is a quad 2 to 1 line multiplexer with storage capabilities. When the 1V signal on pin 10 is low, word 1 will appear on the QA thru QD outputs. When the 1V signal is high, word 2 will be transferred to the Q outputs. The four bit word from multiplexer 4L is then sent to a custom PAL at position 4D.

Page 40

NOTES

This space is provided for personal notes

Page 41

THE COLOR ROM

The five output lines from PAL 4D are used to address a 32 X 8 ROM at position 4C. This color

ROM determines the color and color intensity for each point on the monitor screen. As the monitor

scans a given point on the screen the color ROM will output an eight bit word to turn on various com-

binations of the red, green and blue guns in the picture tube. Note that the eight outputs are arranged

in three groups. DO, D1 and D2 provide the red signal; D3, D4 and D5 provide the green signal; D6 and

D7 provide the blue signal for the monitor. Note also the resistor ladder or analog adder circuit for each

of the three groups of outputs from the color. ROM. The resistor ladder offers more or less resistance

to the color signal resulting in a more or less intense color on the screen.

Examine the DO, D1 and D2 output lines from the color ROM. If D2 is high while DO and D1 are low, the color signal will pass thru R5 (220 ohms) to produce an intense red point. If DO is high while D1 and D2 are low, the color signal will have to pass thru R3 (1K ohms) which is more than four times

the resistance of R5 (220 ohms) resulting in a much dimmer red point. Of course a point of medium

intensity red would occur if D1 is high while DO and D2 are low.

All the colors a monitor is capable of producing are derived from the primary colors red, green

and blue. To obtain the color purple for example, the color ROM would output the byte 10000100 to

turn on the blue and red guns simultaneously. Since white is a mixture of equal parts of red, green and

blue, the byte 11110110 is used to create a white point on the screen. Note that the “byte for white”

uses the 220 ohm and 470 ohm paths for each of the three primary colors. This can be verified by

putting the game into the cross hatch mode and checking the outputs of the color ROM. During the cross

hatch mode pins 2, 3, 5, 6, 7 and 9 are active, while pins 1 and 4 remain low.

The color ROM 4C may cause blurry shadows behind the characters or complete loss of video

if it is faulty. If either of the 100pf capacitors on the outputs of the three color signals is shorted that

color will be lost. Usually if the alphanumerics in the self test are white one can be sure that the color

ROM and the color outputs are functioning properly because ail three primary colors are necessary

to produce a white spot on the screen.

Page 42

NOTES

This space is provided for personal notes

Page 43

THE POWER CHASSIS AND POWER SUPPLY BOARD

The power chassis houses two transformers, the AC line filter and numerous fuses. A service

outlet has been conveniently located on top of the chassis so that AC operated test equipment and

lighting may be plugged into the game without the need for an additional wall socket.

Approximately 115 volts AC enters the power chassis via the line cord. The AC line filter blocks

any noise that might enter via the line cord and a varistor protects against high voltage spikes. The

115 volts AC then leaves the power chassis and passes thru the power and satety switches. After the

switches the 115 volts AC again enters the power chassis to supply the primary windings of the two

transformers. Note the two voltage selection connectors that allow the power chassis to be operated at

105 volts, 115 volts or 125 volts AC.

The game transformer (MT-105A) has two secondary windings. The 30 volt winding is center tapped to yield two 15 volt lines and the 18 volt winding is center tapped to yield two 9 volt lines. To accurately measure the 9 volt and 15 voit lines use the O volt tap on each winding. Each oi the 9 volt and 15 volt lines are fused. If fuses F3 and F4 on the 9 volt lines blow out frequently, use 5 amp. sloblo fuses instead.

The MT-101A transformer isolates the monitor from the main AC line for safety purposes. This

transformer also has a secondary winding of 12 volts. The 12 volt winding is fused and then sent to the

power supply board along with the 9 volt and 15 volt lines from the game transformer.

The power supply was designed to provide three regulated outputs at +5, +12 and —5 volts

DC and one unregulated output at approximately +16 volts DC. The Super Pac-Man system does not

require the —5 volt circuitry or the battery back-up circuitry which might be provided on this board.

The combined Super Pac-Man logic boards (CPU and Video) draw approximately 3.25 amperes

from the +5 volt output. The +12 volt output supplies the audio circuitry on the CPU board. The audio

circuitry may draw between 90MA to 250MA depending on how loud the sound is set and whether

or not sound is occurring. The unregulated +16 volt output is used across the coin door lites.

The two 15 volt AC taps from the game transformer are rectified by diodes D110 and D111

(A15F 3 amp.) and filtered by capacitor C104 (25,000uf 35 volts) to provide approximately +20 volts DC to the +12 volt regulator circuit.

The LM305 at position U5, transistors Q100 and Q104 and associated resistors and capacitors

make up the +12 volt regulator circuit. Potentiometer VR102 can be adjusted to set the +12 volts to

within +.2 volt when measured at the logic boards.

Page 44

Pin number 8 of the LM306 at U5 senses the voltage drop across resistor R102. The voltage drop across a resistor is directly proportional to the current flowing thru the resistor. By sensing the voltage drop across resistor R102, the LM305 will detect excessive current drain and it will shut down

the +12 volt regulator circuit before damage is done to either the power supply or logic boards.

When the +12 volt regulator circuit is functioning properly the base of Q104 will be approxi-

mately 17.5 to 20.5 volts and the base of Q100 will read approximately 12.5 to 13.5 volts when measured

from the “common” \ine. Note that in the +12 volt regulator circuit the input of the LM305 (pin 3) and

the collector of Q100 are both tied to the +20 volt DC line.

The “sense” line to the LM305 at US is connected to “common” via jumper JW2. Capacitor C114 (470xf 25 volts) offers additional filtering after the +12 volt regulator circuit.

The two 9 volt AC taps from the game transformer are rectified by diodes D106 and D107 (MR750 6 amp.) and filtered by capacitor C113 (40,000, 16 volts). The result is approximately +12 volts DC which supplies the coin counter and the collector of the +5 volt pass transistor Q101.

In the +5 volt regulator circuit the input to the LM305 (pin 3) at position U2 is connected to

the +20 volt DC line thru diode D103 and fuse F1. Pin 3 of the LM305 at U2 will read approximately

19.25 volts considering a voltage drop of .7 volt across diode D103. The LM305 senses the voitage drop

across resistor R103 and will shut down the +5 volt regulator circuit if it detects a current drain exceeding 4 amperes. Potentiometer VR101 can be adjusted to set the +5 volts to within =.2 volt when measured at the logic boards. Capacitor C102 (470uf 25 volts) offers additional filtering of the +5 volts

DC. Resistor R134 (68 ohms 1/2 watt) is used as a dummy load and holds down the +5 volts when there is no external load. When the +5 volt regulator circuit is functioning properly the base of transistor Q102 will read approximately +16 volts and the base of Q101 will read +6.5 to 7 voits.

Page 45

NOTES

This space is provided for persona! notes

Page 46

Schematics and Wiring Diagrams

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 50

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 51

LL DDD AEE DDE ca aa

Page 52

Bally MIDWAY ra

November 29, 1982

SERVICE BULLETIN

GAME: SUPER PAC-MAN

SUBJECT: NEW COIN SWITCH CIRCUIT TO PREVENT STRINGING

CONDITION

  • When acoin hangs or the coin switch is operated manually with a long pulse the game will lock-up (credit will show AA).
  • The game will clear the lock-up condition by turning the power off and on.

3, The coin circuit will function normally with coins and will not cause a lock-up condition during normal play.

Andy Ducay Service Manager

AD/dd

=) 10601 W. Belmont Ave. * Franklin Park, illinois 60134 * Telephone (312) 451-9200 + Telex: 72-1596

Page 53

C5ially MIDWAY rre:c

November 29, 1982

SERVICE BULLETIN

GAME: SUPER PAC-MAN

SUBJECT: RACK TEST

  • Coin game.
  • Press 1 player button and start game.
  • When maze and characters appear, freeze game with Switch #8 in the ON position (Dip switch #2 at 5B).
  • Press speed button to advance racks from one stage to another.
  • Return Switch #8 to the OFF position to play game.

Andy Ducay Service Manager

AD/dd

=> 10604 W. Belmont Ave. + Franklin Park, linois 60431 * Telephone (312) 451-9200 « Telex: 72-4596

Page 54

Bally MIDWAY cr

December 14, 1982

SERVICE BULLETIN

GAMES: SUPER PAC-MAN

SUBJECT: POWER CHASSIS TWO 4 AMP. SLOW BLOW FUSES BLOWING

MODIFICATION

1, Replace the two 4 amp. slow blow fuses with 5 amp. slow blow fuses.

  • Check game electrically.

Andy Ducay Service Manager

AD/dd

  • 10601 W. Belmont Ave, « Franklin Park, Illinois 60131 * Telephone (312) 451-9200 « Telex: 72-1596 @
Page 55

CBallly MIDWAY ire

February 2, 1983

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cel! by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metat-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and jow-power requirements, or other advantages (static will damage a MOS chip).

Andy Ducay Service Manager

AD/dda

D 10601 W. Beimont Ave. « Franklin Park, Illinois 60134 * Telephone (312) 451-9200 * Telex: 72-1596

Page 56

SERVICE BULLETIN

&) MOTOROLA MCSRORE MCS8AQ9E (1.5 blz) MCBSBOSE

&-BIT MICROPROCESSING UNIT The MCGBQ8E is @ revolutionary high performance &-bit microprocessor which supports modem programming techniques such as position independence, reentrancy, and modular programming. This thid-generatiun addition te the M6800 family has major architecturat improvements which include additional registers, instructions and addressing modes. The basic instructions of any computer are greatly enhanced by the presence of powerful addressing modes. The MC6808E has the most com- Piete set of addressing modes available on any &-bit microprocessor today. The MC6809E has hardware and software features which make it an ideai processor for higher level language execution or standard centrolier applications. External clock inputs aie provided to allow synchronization with Peripherals, systems er other MPUs MC6800 COMPATIBLE @ Hardware — Interlaces with At| M6800 Peripherals © Software — Upward Source Code Compatible Insiruction Set and Adgressing Modes ARCHITECTURAL FEATURES @ Two 16-vit Index Registers © Two 16-bit indexable Stack Pointers Two Bbit Accumuiators can be Concatenated to Form One 16-Bit Accumulator © Direct Page Register Allows Direct Addressing Throughout Memory HARDWARE FEATURES External Clock inputs. E and Q, Allow Synchronization TSC Input Controls Internal Bus Buffers UC indicates Opcode Fetch AVMA Allows Efficient Use of Common Resources in A Multiprocessor System BUSY is a Status Line for Muhiprocessing Fast interrupt Request Input Stacks Only Condition Code Register and Program Counter interrupt Acknowledge Output Allows Vectoring By @evices SYNC Acknowedge Output Alows for Synchronization to External vent Single Bus-Cycle RESET Single 5-Volt Supply Operation Inhibited Alter Until After First Load of Stack Pointer @ Early Address Valid Allows Use With Slower Memories Early Write-Data for Dynamic Memories ‘SOFTWARE FEATURES © 10 Addressing Modes ‘+ M6800 Upward Compatible Addressing Modes Direct Addressing Anywhere in Memory Map Long Relative Branches Program Counter Relative True indirect Addressing Expanded Indexed Addressing’ 0, 5, 8, or 16 bit Constant Offsets 8, of 16-bit Accumulator Offsets Auto-Increment/ Decrement by 1 or 2 Improved Stack Manipulation 1464 Instructions with Unique Addressing Modes 8 x B Unsigned Multiply 16-bit Arithmetic Transter/ Exchange All Registers © Push/Pull Any Registers or Any Set of Registers © Losd Effective Address, r

(HIGH-DENSITY N-CHANNEL, SILICON-GATE)

8-BIT MICROPROCESSING UNIT

SUFFIX CERAMIC PACKAGE CASE 718

P SUFFIX PLASTIC PACKAGE case7it

vil § surex tl CERDIP PACKAGE Gute CASE 734 ee |

FIGURE 1 — PIN ASSIGNMENT

Page 57

Chip Number

74LS04 74LS08 74LS32 74LS74 74109 74LS138 74LS157 74LS158

74LS161 74L8245 74LS257 74LS259 74LS273 74LS367 74LS368 MC68A09

Chip Number

74LS00 74LS04 741S08 74LS10 74LS20 74LS32 74LS74 74LS86 74LS138 74LS157 74L5161 TALS245 74LS273 74LS298 74LS365, 74LS368 SUPER PAC-MAN CPU BOARD (P.C. A084-91436-C316)

Function

Hex Inverters Quad 2 Input AND Quad 2 Input OR Dual D Type Flip-Flop Dual JK Type Flip-Flop 3 to 8 Line Decoder/Multiplexer Quad 2 to 1 Line Multiplexer Quad 2 to 1 Line Multiplexer — Inverted Outputs 4 Bit Binary Counter Octal Bus Transceivers Quad 2 to 1 Line Multiplexer — Tri State 8 Bit Addressable Latches Octal D Type Fiip-Flop Hex Bus Drivers Hex Bus Drivers — (nverting CPU Chip

Number Function

2764 8K x 8 EPROM 2732 4K x 8 EPROM AM9114 1K x 4 RAM MBM2148 1K x 4 RAM 2114 1K x 4 RAM SP1-1 PAL SP1-2 PAL SP1-3 256 x 4 PROM M7052 18.4320 Crystal

MC14066 = Quad Bilateral Switches

MB3730 Audio Amplifier O7XX Custom Horizontal & Vertical Sync Generator 15XX Custom Address Generator 16XX Custom Bus Controller BEXX Custom I/O Ports

SUPER PAC-MAN VIDEO BOARD (P.C. A084-91435-C316)

Function

Quad 2 Input NAND Hex Inverters Quad 2 Input AND Triple 3 Input NAND Dual 4 Input NAND Quad 2 Input OR Dual D Type Flip-Flop Quad 2 Input XOR 3 to 8 Line Decoder/Multiplexer Quad 2 to 1 Line Multiplexer 4 Bit Binary Counter Octal Bus Transceivers Octal D Type Flip-Flop Quad 2 Input Multiplexer (With Storage) Hex Bus Drivers Hex Bus Drivers — Inverted Outputs Chip

74LS377 Octal D Type Flip-Flop 74LS378 Hex D Type Flip-Flop 2764 8K x 8 EPROM 2732 4K x 8 EPROM 2148 1K x4 RAM M58725 2K x 8 RAM OOXX Custom Address Generator 04xx Custom Address Buffer 07XX Custom Horizontal & Vertical Sync Generators 11XX Custom Bit Shifter 12XX Custom Address Generator SP1-7 PAL 3160-15AXL-CXPD 256 x 4 PROM 3160-15AXL-BXPD 256 x 4 PROM 3160-03AAC-AXPD 32 x 8 PROM

Page 58

Bally/Midway’s

Conquer the Fruit-Filled Maze! Play Super Pac-Man and find a super new Pac-Man challenge. Super Pac-Man mazes are made up of delectable fruits and goodies rather than white dots, and also contain 4 energy dots, giving Pac-Man the power to chomp down pursuing monsters, and 2 “Super” dots. When Pac-Man eats a “Super” dot he becomes...SUPER PAC-MAN! Now 10 times his normal size, Super Pac- Maan is totally invincible to monsters and can crash through locked gates as he chomps down rows of fruits! Munch the Keys to Locked Gates! Each maze contains several locked gates that must be opened before Pac-Man, in regular Pac-form, can pass through. By eating the corresponding keys our hero is free to pass through the gates and devour the fruits or objects inside. Rack Up Big Bonus Points! Every third Super Pac-Man maze is a bonus rack. Pac-Man is in “Super” form throughout, racing the clock for Super Pac-Man scores! At random intervals, a star will flash. When Pac-Man eats the flashing star, he scores bonus points for special fruit/object combinations and matches! Super Speed for Super Pac-Man Press Super Pac-Man’s super speed button on each side of the joystick and away he goes with an extra burst of speed. ff Once you push the Super Button you'll be a Super Pac-Man lover forever!

Cabinet Specifications:

Upright Mini Cocktail

® Height 73" Height 60%" Height 29" Width 2672" Width 19%" Width 32” MIDWAY MFG.CO. Depth 34" Depth 23%" = Depth 22" ©1982 BALLY-MIDWAY MFG. CO.

10601 W. Belmont Avenue Franklin Park, Illinois 60434 Telephone (312) 451-9200