CATHODE RAY TOMES

Twin Racer TM-021

Twin Racer (Kee Games Inc.) · Technical Manual · 25 pages · 7 sections · original scan

Page 1

TWIN RACER

TM-021

tri}

OPERATION AND SERVICE MANUAL

KEE GAMES INC. a subsidiary of

14600 Winchester Blvd. Los Gatos, CA 95030 Telephone (408) 374-2440 Telex 357-488 Another NEW KEE GAME feature. b)

AN OIL SLICK

ON THE

TRACK!

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

TABLE OF CONTENTS

INTRODUCTION AND WARRANTY INFORMATION . .

BASIC CONSTRUCTION AND ACCESS. .....

RECEIVING INSPECTION PROCEDURES .....

GAME SEQUENCE. . 2... ee ee ee

UPPER SECTION SUB ASSEMBLIES. ......

MOTOROLA TV ADJUSTMENT. . 2... ww ee

MAINTENANCE AND TROUBLESHOOTING PROCEDURES

ELECTRONICS TRAY SUB ASSEMBLIES .....

FRONT CONTROL PANEL... .....-..

Page 4

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 5

INTRODUCTION AND WARRANTY INFORMATION

Twin Racer is a coin operated video amusement game giving the players the

feel and the performance of a high speed formula car race. Greatly enhancing

the dimensions of the game are the almost life-like sounds of acceleration,

shifting, braking, and crashing, as the cars are driven around the course.

The electronic circuits of this game are solid state for long life and

low maintenance. Pedals, steering and shifting assemblies have been

designed modularly for easy removal and servicing.

As with all extremely sophisticated race cars, Twin Racer is subject to

minor breakdowns. The printed circuit boards (PCB) are covered with a one

year warranty. The Motorola TV Monitor is also covered under warranty

for a period of thirty days. The warranty commences on the date of

shipment.

If either the P. €. boards or the TV fail after their specified warranty

period, KEE GAMES will repair the item for a nominal parts and labor

charge. The TV monitor, after the warranty period, may be taken to a

competent TV repair shop.

If any questions arise concerning the warranty repair or replacement,

contact your distributor or KEE GAMES at (408) 249-6090 and ask for

Mike Sieler or Gary Kinney in Distributor Services.

Page 6

BASIC CONSTRUCTION AND ACCESS

There are two openings through which to gain access to the inside sub-

assemblies: the coin mech door and the rear door. Each of these

openings provide easy and convenient access to all necessary points.

The coin mech door provides access to all of the coin handling equipment

and the foot pedal mounting bolts. The rear door gives access to the PCB

computer, rear of the TV monitor, the steering, shifting, starter switch,

and automatic shift components.

All of the major sub-assemblies have been designed for easy servicing and

replacement. All assemblies can be removed easily after the retaining

bolts and wiring have been removed.

RECEIVING INSPECTION PROCEDURES

Immediately upon receiving the Twin Racer game, uncrate the game and

inspect the outside area for any damage that may have occurred during

shipping.

Each and every new Twin Racer that leaves the factory is carefully

checked and properly adjusted for maximum performance. However, since

vibration and environmental changes can alter some of the adjustments,

the following is a list of steps to follow in your inspection of the

game :

Page 7
  • With the machine unplugged, open both doors, front and rear,

and give the insides of the game a good eye inspection. Look for wires

that may have been loosened or for screws, bolts and nuts that may need

tightening. Check the individual sub-assemblies for proper function

(i. e., steering, shifter, etc.), making certain at the same time that

each item is mounted securely. Be watchful for any foreign matter that

may Short electrical connections. Check for tightness of all plugs and

sockets. The power cord can be found outside the rear of the cabinet.

  • Plug in the power cord using the appropriate voltage (indicated

on the serial number sticker on the rear of the game cabinet. After a few

moments, of warm-up the CRT (cathode-ray tube) should display the race

track, scores, and race cars. The picture should be sharp and clear

exhibiting the proper levels of brightness and contrast. The background

should be black and game details should be Tight and distinctive.

  • Check the coin mech operation with several old and new coins. No

genuine coin should be rejected. Pressing the starter switch, located on

the center of the front panel, should start the game by resetting the

score to 0 and the car's engine beginning to idle with a wild hot-cam

effect. Inside the start switch is an LED (light-emitting diode) which

should light up indicating credit of play. After starting the game, check

the function of the pedals and the steering and shifter. The automatic

shift button places the shifter into third gear and enables a new player

to get acquainted with the game without having to worry about shifting.

  • The playtime is preset at the factory for approximately a minute

and should not be changed.

  • Check the doors to see if the locks bind in the "locked" or

"unlocked" position.

Page 8

GAME SEQUENCE

With the game plugged in and the rear door closed, the CRT will display

the attract mode. The attract mode displays the race track and the cars

in a stationary position where the last players left off, plus the scores

of the last game.

Depositing a quarter in the coin slot lights the credit light on the

starter switch indicating a game credit. Depressing the starter button

resets the score to zero (0), the cars return to the starting grid with

engines idling.

The controls of the game, movements and sounds of the cars simulate that

of real-live racing formula cars. The players have the option of a manual

or automatic transmission. When the gas pedal is depressed the car begins

to move. If the manual transmission is chosen, the player shifts up to the

next higher gear when the revs reach their peak until hitting the peak rpm

in third gear. The shifter is a standard three on the tree pattern with

reverse included.

The steering wheel causes the car to turn in the direction of the rotation,

but it is not necessary to bring the steering wheel back to its center

position.

Stepping on the brake pedal will bring the car to a skidding halt with a

realistic sound accompanying it. If the steering wheel is turned with the

brakes on, the car will still head in the direction of the skid, reacting

Page 9

like that of a real-live panic situation.

The points for the score on the CRT are made each time the car passes

over hidden score positions, if and only if, the correct pattern around

the course is followed. A total of ten points is obtainable for each

lap completed.

SERVICE PROCEDURES

UPPER SECTION SUB-ASSEMBLIES

The following procedures are steps that are to be taken in order to

service the illumination lamps, the plexiglass, the bezel, the lap

timer and to repair the TV Monitor.

  • Plexiglass Removal: To remove the plexiglass, open the

rear door and reach up inside the cabinet and remove the three nuts

used to secure the aluminum bracket. With this bracket removed,

carefully slide the plexiglass up and out. To reassemble, follow

the reverse of this procedure.

  • Illumination Lamps: There are 11 6-volt #GE47 lamps mounted

on an aluminum support plate directly behind the upper portion of the

plex. If these need replacing, follow step #1 to remove the plexiglass.

With the plexiglass removed the lamps can be taken out by pushing on the

bulb then turning it to the left and pulling the bulb out. To reassemble,

follow the reverse of this procedure.

Page 10
  • T. V. Monitor Removal: To remove the entire Motorola TV, unplug

the socket on the rear of the monitor and unplug the molex socket going to

the illumination lights. Do not remove the Monitor from the shelf. With

all the mounting screws removed the TV can be slid out from the front of

the game. To reassemble, follow the reverse of these steps. Feed these

wires through the hole in the T.V. mounting board and slide the T.V. and

its mounting board out.

Page 11

MOTOROLA TV ADJUSTMENT

The adjustment of the Motorola TV monitor functions like that of a normal

TV set. The only exception to that is that the audio portion of the TV

is not used. The volume control is located on the analog PCB computer.

The monitor is adjusted through the rear door.

  • Brightness: Adjust the brightness before the contrast. Adjust

so that the CRT background is as dark as possible.

  • Contrast: The contrast is adjusted so that the images displayed

on the CRT are as bright and clear as possible without being blurred.

  • Vertical Hold: The vertical hold should only be adjusted if the

picture is rolling up or down the screen. Adjust for a stable centered

picture.

  • Horizontal Hold: If the picture is slightly off-center horizon-

tally, or if the images appear warped, or if the picture is broken into a

series of diagonal lines, adjust the H Hold.

  • Vertical Size: Adjust only if the top and bottom of the race

course is cut off from the visible portion of the screen or there is too

much distance between the edge of the course and the edge of the screen

which will appear as an extra set of horizontal dotted lines on the top

and bottom of the CRT display. Adjust for maximum picture size.

  • Vertical Linearity: Change this adjustment only if the top of

the picture seems compressed.

  • The Yoke: The yoke should never need adjustment unless the

adjuster has been tampered or damaged. If yoke adjustment is necessary, rotate

both yoke rings simultaneously for optimum centering of race course on the

CRT.

Page 12

MAINTENANCE AND TROUBLESHOOTING PROCEDURES

Twin Racer, due to its solid state circuitry, will require very little

maintenance other than periodic cleaning, lubricating and TV adjusting.

The cabinet and plexiglass screen may be cleaned with any non-abrasive

household cleaner. The coin acceptors and the lock cylinders should be

lightly sprayed with WD-40 or a similar silicone lubricant, once every

three months. The TV monitor is adjusted only if the picture is

incorrect.

In troubleshooting the Twin Racer amusement game, the first real step

is to correctly identify the problem with the observable symptoms of

the malfunction. Examine the game carefully for a correct diagnosis.

  • The TV Monitor: Many TV problems can be corrected simply by

proper adjustment. But if the problem persists, or if the TV is

undoubtedly malfunctioning, contact your distributor or remove the

TV monitor and take it to a competent local TV repair shop. Complete

TV monitor repair manuals are available from the KEE GAMES Customer

Service Department, 330 Mathew St., Santa Clara, Ca. 95050. Phone

(408) 249-6090 or Telex: 357441

  • The PC Board Computer: Most PCB malfunctions will not be

within your scope to repair. If you can positively determine that the

PCB has failed, contact the distributor from whom the game was obtained

for repair or replacement instructions. Some problems that might appear

Page 13

as PCB problems could possibly be the result of improper TV adjustment

or the various small blue trim pots located upon the PCB are out of

adjustment. DO NOT ATTEMPT TO REPAIR THE PCB YOURSELF UNLESS YOU

HAVE BEEN SPECIFICALLY INSTRUCTED TO DO SO BY YOUR DISTRIBUTOR. To

do otherwise will void the PCB warranty.

  • The Wiring Harness: For troubleshooting purposes, the

harness includes the line cord, fuse, line filter, transformers, the

start coin and automatic shift switches, steering assembly, gear shift,

pedals, PCB edge connector, TV monitor, speaker, lap timer, illumination

lamps and all of the interconnecting lengths of wire.

  • Suggestions: The follwoing are some specific instructions and

suggestions for troubleshooting the Twin Racer game. To perform even

the most simple troubleshooting procedures, there must be available a

VOM (Volt Ohmeter) and, if possible a VTVM (Vacuum Tube Volt Meter)

or digital Voltmeter. It is also helpful to have another Twin Racer

game on hand for substitution purposes.

For many problems, substitution may be the easiest way to troubleshoot

the game. For example, if a PCB malfunction is suspected, substitute

a known-to-be-good PCB. If the problem disappears, then the first PCB

is the troublemaker. But, on the other hand, if the problem still persists, then the malfunction must be in either the harness or the

TV monitor. Conversely, the same goes for the TV monitor concerning

substitution.

Page 14

The harness must be checked by eliminination. Substitute a known-to-be

good TV and PCB, and if the malfunction persists, the harness and

associated mechanical or electronic equipment must be at fault. The

harness can also be checked with an Ohmeter and a continuity checker.

  • T. V. Monitor Troubleshooting: Some typical TV problems are

distorted display, raster only, or no video at all. If you do not have

a raster (a raster is a lighted but blank TV screen with the brightness

turned all the way up), begin checking the power supply to determine

if the TV is getting power. If the general illumination lamps of the

machine are lighted, at least you know that power is reaching the

machine. If not, check your line cord, interlock switch, fuse, etc.

If it is A. C. power, go around to the back of the machine and with

the rear door open (and interlock switch defeated) listen for a hum

emanating from the monitor. If there is a hum, the monitor is powered

and you may have a defective CRT or similar problem. Another test (and

one which can be performed in a noisy environment) is to measure the

voltage between the TV fuses and ground. If your voltmeter reads 110

volts or more, you know the monitor is powered. If not, check the

fuses, the TV connections and the harness to see why power is not

reaching the monitor. If the TV is powered but still not functioning,

check the TV AC voltage switch which should be set to the "115"

position ("115" visible on the switch) if it is connected to a 110

volt line source. If you have the correct voltage after the fuses, but

the monitor still will not function, you have two choices: (1) Remove

the monitor and take it to a specialist, or 2) Turn to the TV schematic

Page 15

and start exploring the monitor with a VIVM and an oscilloscope. If you

do have a raster, you must determine why there are no video signals being

displayed on the screen. These video signals are generated by the PCB

computer and enter the monitor through pin (#1) of the TV monitor

connector.

  • Steering Assembly Troubleshooting: Four small red LEDs have

been included on the main PCB near position H8 to aid in troubleshooting

the steering electronics.

Mounted on the small steering assembly PCB are two phototransistors and

two infrared light emitting diodes. The phototransistors are mounted

behind the tack ring in such a way that the slots in the wheel break up

the light emitted from the diodes. This generates pulses which are used

by the computer to determine how quickly and in which direction the wheel

is being turned.

The test LEDs on the analog PCB will light whenever the infrared diodes

are stimulating the phototransistors (i. e., whenever the diodes are

"shining" through the slots in the slotted wheel onto the transistors).

To test the steering wheel assembly, simply rotate the wheel slowly in

both directions while watching the two red LEDS on the main PCB. If your

steering assembly is 0.K., both LEDs will flicker. If both of the LEDs

fail to light (or remain lit constantly) while wheel is being turned, you

definitely have a malfunction before the main PCB, which may be either in

the wiring harness or in the steering assembly PCB.

  • Troubleshooting By Symptom:
  • No Power: Check for correct line voltage and if 0.K. then

Il

Page 16

b)

d)

9)

i) check the fuse on the electronics tray, interlock switch and

the transformer primaries.

No TV Picture: Check for power as per procedure #a (NO

POWER) and if 0.K., check TV connector and TV fuses. Measure voltage at TV fuses (should be 110 VAC) and if 0.K., replace

the TV monitor. Check C-29 (.56 uf) and Horizontal Output

Transistor.

TV Raster Only: Check the harness and especially the PCB

edge connector. If 0.K., check the TV as per the special

test under "TV Troubleshooting". Or check TV or PCB by

substitution.

TV Picture Rolls: Adjust the TV vertical hold and if the

rolling persists, check the TV or the PCB by substitution.

TV Picture is Wavy: Adjust the TV horizontal hold and if

the problem persists, try replacing the transformer (in the

monitor itself).

TV Picture is Broken into Diagonal Lines: Adjust the TV

horizontal hold and if the problem persists, check the TV

or the PCB by substitution.

No Game Credit: Check the coin switches, the start switch,

the harness and the positions of the PCB slide switches.

If the problem persists check antenna wire and try substi-

tuting a new PCB.

No Game Start: Check the coin switches, the start switch,

the harness and replace the PCB if necessary.

Game Credit Shuts Off or Picture Shrinks: Check the line

Page 17

5)

k)

1)

n)

0) voltage with your VOM and be aware that a large motor

starting up (i. e., an air conditioner) may drop the

line voltage. Check to see that machine is firmly

Plugged in. If the problem only occurs at certain

times of the day your trunk line voltage may be

dropping.

No Audio: Check the volume controls, speaker connec-

tions, and for 20 volts. If the problem persists, test

the speaker and if the speaker is 0.K., try replacing

the PCB.

Game Sequence Incorrect, Parts of the Race Course, Car,

Score Missing or Distorted: Replace the PCB or check

for proper power supply as described in "Troubleshooting

the Power Supply."

Car Will Not Steer or Turns in One Direction Only: Check

PCB LEDs as per procedure #6 and if 0.K., then replace the

PCB computer. If LED test is 0.K., check steering harness

and connections and for foreign matter in steering assembly.

Replace steering PCB if necessary.

No Brakes: Check brake switch and wires from brake pedal

switch to PCB. If 0.K., check the PCB.

Brakes All the Time: Check brake switch for foreign

material and/or shorting terminals.

No Accelerator: Follow procedure #m for "NO BRAKES".

Accelerator all the Time: Follow procedure #n.

Page 18

q)

r)

s)

t) All Four Gears Dead: Check connections and wires from

gearshifter to PCB, check automatic shift switch.

One, Two or Three Gears Dead: Check the connection and

harness of the malfunctioning gear (s): check the shift

switch(s) for the malfunctioning gear(s). If problem

persists, replace PCB.

No Automatic Shift: Check the wires on the switch. If

all are correct, check the switch itself.

No Lamp Lit on Automatic Shift Switch: Check power

and replace if lamp burned out.

Page 19

SERVICE PROCEDURES

ELECTRONICS TRAY SUB ASSEMBLIES

(Power must be turned off when replacing parts).

1) Fuse Replacement: If the fuse is blown replace with, and

only with, a 1 Amp, 125 volts Slo-Blo fuse (313-3AG). When

replacing the fuse be certain the game is in proper working

order, as the fuse would only blow if something was mal-

functioning.

Transformer Replacement: To replace a defective transformer,

note down on paper the color and position of each wire, and

remove the wiring. There are two screws that mount the

transformer to the cabinet. Remove these. When replacing,

make certain to reconnect all wires in their proper place.

Printed Circuit Computer Board: To remove the PCB computer,

disconnect the edge connector and remove the retaining

screws carefully. Remove the board. The PCB is very

delicate and fragile and requires extreme care in handling

and shipping.

P.C. Board Adjustments:

  • Volume: This adjustment is made by the small blue trim

pots marked "volume" located on the analog board, on the

left side of the cabinet. Adjust the volume according

to the locations need but remember that the volume will

sound louder with the door off.

Page 20

b)

c) Playtime: This adjustment is located near H-9. The play time

trim pot adjusts the length of the game and also the crash time.

The playtime pot is preset at the factory for 1 minute and should

not be adjusted due to its interrelations with other game functions.

Special Adjustments: If the following symptoms occur, the board

must be returned to the distributor from whom you obtained the

game.

  • The car seems to move too slowly.
  • The sound of the engine is distorted.
  • The sound of the skid with brakes applied is wrong.
Page 21

SERVICE PROCEDURES

FRONT CONTROL PANEL

To service the rear side of the control panel, open the rear door to the

cabinet.

  • Gear Shift Assembly: Record the wire colors and position and

2) remove. The shift assembly can be removed after undoing the

four mounting screws.

To open the gear shift assembly, remove the four screws on the

securing tubs, while holding the two halves together. Carefully

split the housing halves so that the internal parts will not

spring away and become lost. With the housing halves separated,

the gear shift rod, spring, ball, detent and switch actuators

will all be accessible. When reassembling the gear shift unit,

lubricate all of the surfaces exposed to wear with a small

amount of silicone grease. make sure that the housing screws

are replaced in the exact same way as removed.

Pedal Assembly: The pedal assembly must be removed from the

game in order to replace the brake and accelerator switches.

To remove the pedal sub-assembly, reach in the front door and

remove the three mounting nuts. From the front of the pedals,

pull the assembly out from the game towards you and lift up.

Unlocking the wires, making note of wire color and position,

frees the pedal assembly from the cabinet.

Page 22

3) Steering Wheel: To remove the steering wheel, remove the shaft

end nut and pull the steering wheel out from the front. Undo the

three socket head bolts and the long bolt to completely divorce

the wheel from the rest of the assembly. To replace the steering

PCB, remove the shaft end nut and tack ring. The board can be

replaced after removing the two mounting screws.

To replace the steering wheel bushing assembly, remove the steering

wheel and also the six retaining screws which hold the backing plate

to the control panel. Withdraw the bushing assembly through the

front of the panel.

When reassembling, lightly lubricate the bearing surfaces with a

small amount of silicone grease.

Starter Button: Note the position and color of each wire and

unplug from the switch. Then unscrew the switch from the barrel

assembly.

Automatic Shift Button: To remove this switch, record the color

and position of the wires and remove. Push the four mounting

and securing tabs against the switch and push the switch out to

remove.

Page 23

ANALOG - El

  • OGE_GONN es) 25V6 HOV xc_6Onz,,

AC POWER STEERING

AC oer PEs BD ICOIN-COUNTER B BRAKE - B GAS —8 o)

6v,DISPLAY BD-TO TVTERM! -OUT ANALOG BD

CON SuITCH=NCOZ” OATES cwA 30 SCREECH Bt CRASH 5 __owts SCREECH A¢ CRASH A Sree POLE we xe M@SCREECH A CRASH B e echisH & se SPEED PULSE A |= GEAR R-GEAR o[a[wjola[s[o[r}—

REVERSE A I9@SPEED KUL A OCR A ae @ ATTRACT -sv @ ay tov 030 O+5y GND@ —31@GND WOVac 60 nz GND €34 — @GRKO

S| auTo cee. HET B D =| DIGITAL- EDGE-CONN re °y ty eno _fejs

S27wre]ac

J Ac START -2 —— JLED-CREDIT - 2 ~~ START — | Gas” TBRAK al COIN-MECHS _ LED-CREDIT- | 1 Le VIDEO ‘|

~ PL 4|[COIN -MECH-NO

|COIN_ MECH —NC >[B) Io

|COIN-COUNTER

+5V

+5V +8 GAS-A\ STEERING— B STEERING - B B c

[°) E F

H J K =|" } “GAS | BRAKE “pyt

START 2 PLAYER Tm RYE laawe alolz BRAKE — A AUDIO AUDIO -A STEERING A STEERING A

TEST OUT [Pte] =fe[s[o}

GND. ra (COn-COUTER | AC ! ise. Logg LOUD- SPEAKERS EV TC DISPLAY- ACARD > K4DRTA-HARNESS, ELECTRIC-OWG (N= AO, 2 = rte — ‘pawn we | °

TV A

=74] ELI. KEE GAMES . INC

SH | OF 2

Page 24

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 25

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.