CATHODE RAY TOMES

Relief Pitcher TM-376 1st Printing

Relief Pitcher (Rev D, 07 Jun 1992 / 28 May 1992) (Atari Games, 1992) · Technical Manual · 52 pages · 77 sections · original scan

Page 1

‘RELIEF GAMES

PITCHER

Ait Dose tha fib a Ligmorte tipsis

Page 2

%

This entire manual was printed on recycled paper

Page 3

A,

ATARI

GAMES

Conversion kit for upright games

Page 4

Copyright © 1992 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S Copyright Act of 1976, This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. 7» may vS \ “ ia

In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95036 03/92 Produced by the Atari Games Technical Publications Department. Writing and Editing: Andrea Dencker Illustration and Design: Mary Ohane: Printed in the U.S.A.

an Sumner NOTICE RE.

NON-ATARI

PARTS

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts nof supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram. ¢ The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (FMI) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with all screws in place and tightened If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

SAFETY UMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game unti it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a ihree-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the contro} panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game.

AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual.

Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using, non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

“il

Page 6

1 Installation

How to Use This Manual .............. 1-1 Cabinet Equipment Requirements 1-2 Tools Required..... 1-2 Inspecting the Kit 1-4 Preparing the Cabinet for the Kit Installation 1-4 Assembling the Control Panel... 1-4 Connecting the JAMMA Harn 1-6 Installing a Baseball Card Dispenss 17 Installing the Relief Pitcher Board Set ......c.cccee 1-7 Installing the Bezel, D , Labels. Attraction Assembly 1-8 Setting the Coin and Game Options. Maximizing Farnings Game Play... 2 Self- Test

Introduction ..... Entering and E: Self-Test Menu... Adjust Volume. Statistics ..... Game Option: Regional Setting: Card Dispenser Option Coin Options....... Sound Board Test Controls Test ..

Alphanumeric Motion Object Te: Playfield Tests Monitor Tests

  • Troubleshooting and

Maintenance

Introduction .......ceeee Video Display Syne Problems Troubleshooting... Removing and Repl: ROMs and RAMs.. 4 Parts Illustrations

See the List of Illustrations that follows.

5 Schematic Diagrams

See the List of Ilustrations that follows.

Statistics Sheet

iv

Page 7

Figure 1-1 Figure 1-2

Figure 1-3

Figure 1-4

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15

Figure 4-1 Figure 4-2 Installed Kit Parts... see 13 Locations of Control Panel Holes to be Drilled... 1-6 Hole-Cutting Template for Relief Pitcher Kit Control Panel (Left Side).... 1-11 Hole-Cutting Template for Relief Pitcher Kit Control Panel (Right Side)...

Self-Test Menu Screen. Adjust Volume Screen. Game Stati: Game Options Screen . Regional Settings Screen . Coin Options Screen ..... Sound Test Screen .. Controls Test Screen RAM Tests Sub-Menu. ROM Test Screen ..... Alpha Test Screen vcs Motion Object Test Screen. Playfield Scrolling Test Screen Color Test Screen... Convergence Test Screen ..

Parts of Relief Pitcher Universal Kit.... 4-2 Control Panel Parts .............. Figure 4-3

Figure 4-4 Figure 4-5

Figure 5-1

Figure 5-2

‘Yable 1-1 Table 1-2 Table 1-3

Table 2-1 Table 2-2 Table 2-3 Table 2-4

Table 3-1 Table 3-2

Table 3-3 Table 3-4 8-Position, Gold-Contact Joystick AS embly .. Relief Pitcher Game PCB ‘Assembly’. Relief Pitcher Audio PCB Assembh

Relief Pitcher Game PCB Assembly Schematic Diagram.. Relief Pitcher Audio PCB Schematic Diagram...

Equipment Requirements Contents of Relief Pitcher Kit JAMMA Pin and Wire Connections

Summary of All Self-Test Screens... Game Option Settings Coin Option Settings When to Run the RAM Tests ......

Troubleshooting Table. Voltage Inputs and Test Points 0 on the PCBs.. What ROM ‘Problem Look Like. Atari Games Video Connector Pin Assignments............

Page 8

ui

Page 9

CHAPTER 1

Installation

he Relief Pitcher” con-

version kit is a two-

player game for a standard upright cabinet. 8 This manual provides information You can troubleshoot the PC

boards, main circuits, and

controls using the screens in the self-test. You should regu-

larly test the boards and confor installing, testing, and troubleshooting the Relief Pitcher” conversion kit. 8 Chapter 1 describes how to install the Relief Pitcher kit in your cabinet. This chapter also describes game play. 8 Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the Relief Pitcher game. trols with the self-test to keep your game in peak condition and at top earnings. 8 Chapter 3 contains troubleshooting and maintenance procedures for the controls. & Chapter 4 contains the kit parts list and parts illustrations, 8 Chapter 5 contains the schematics for the Relief Pitcher printed-circuit boards.

Page 10

CHapTER 1 ~ INSTALLATION Rewer Prrcuen

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements

Table 1-1 lists the equipment required in the cabinet into which you are installing the Relief Pitcher kit

CAUTION Do not unplug or plug in the Relief Pitcher game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-to-peak positive polarity Video Display

Control Panel : Metal only

82, 10W +5 voc or +12 VDC

Three-conducior with ground +5 VDC + 0.25V @3.0 amps +12 VDC @ 1.0 amp - -5 VOC @ 1.0 amp optional) Speaker

Coin Counter

Power Cord

Power Supply Tools Required

© Drill with a 1/2-inch and 5/16-inch drill bits

  • Phillips screwdriver ¢ Flatblade screwdriver

¢ Socket wrench set and ratchet

© 5/32" hex wrench

© Wire cutters and strippers - © Straight edge © Squeegee

  • X-ACTO™ knife
  • Insulated wire connectors Gif you are installing a new JAMMA harness)
  • Carbon paper
  • Saber saw

Part No. Descriptio

72-6608S #6 x 1/2"Long, Type AB, Pan-Head, Cross-Recessed Screws (4) 75-5112B. #10-24 x 3/4 “Long Black Carriage Bolts (12) 038158-01 Product |.D. Label 039450-01 FCC Compliance Label 047205-01 Attraction Shield . 047209-01 Control Panel Cover 049962-01 Side Panel Decals (2) 049963-01 Attraction Panel Film

049964-01 Control Panel Decal 049965-01 Monitor Bezel with Graphics 049967-01 Sheet of Control-Panel Labels 141026-001 1/2-1.D. Ferrite Split Beads (4) 160044-001 Snap-Action Switch 171099-001 8-Position Black NO/NC Joystick Assembly with Gold-Plated Switch Contacts (2) 171104-001 Round Pushbutton Switch Assy. with Gold _ Contacts, in 3 Sections: Red, Yellow. and Green (2) 175014-1040 #10 Flat Washers (12) 177026-0040 — #10-24 Zinc Nut/Washer Assemblies (12) 178032-002 #10 Wire & Cable Ties (2) 178283-011 “START" Indicator Plate 178237-004 White Start Button Assembly

178265-001 L-Style Nylon Standoffs (4) TM-376 Relief Pitcher Universal Kit Installation Instructions (with control pane! template) x A046501-01 JAMMA Harness Assembly (optional) A050247-01 Relief Pitcher PC Board Set Packaging materials are not listed. All parts are a quantity of 1, except as noted in parentheses. Table 1-1 Equipment Requirements Table 1-2 Contents of Relief Pitcher Kit

Page 11

Reuer Pircher & CHAPTER 1 — INSTALLATION

049965-01 Bezel W/ Graphics 178056-002 12" W. x 416" T, | 04720801 Foam Tape | Attraction Shield (2pieces, 2" long) a (049953-01

Attraction Film

049962-01 Side Panel Decal 178237004 } | (@ Places) 171099-001 White Button 8-Posiion Gold- Assy Comact Joystick Assy 180044-001 (2 places) Snap-Action 75551128 Switeh ed) | A050247-01 #10 Camiage Bott 178283-011 i : . ‘ Board Set Assy., (8 places) a jicator Plate consisting of: 175014-1040 : ‘A049727-03 410 Flat Washer A elie Pitcher (6 places) Game PCB Assy. 177010-240 05013501 10-24 LockNut Reliel Pitcher Audio EPROM Assy. ‘A050279-01 60-Creuit PCB ae Ribbon Assy. 034536-12 Foam Vibration Damper 178265-001 LSple Nylon Standott : (4 Places) 019964-01 | "72-6608S Contre! Panel : eben. Decal : Ho. Screw 04720901 (4 Fraces) Controt Pane! Cover!

171404-001 | | Gold Centact J Pushbta. Switch Assy. (2 places) = = 049967-01 Controt Panel Label

75-5112B #10 Carriage Bolt (4 places) 175014-1040 #10 Flat Washer (4 places) 477010-240 #10-24 LockNut (4 places)

NOTE For details on label placement, see Figure 4-2.

Figure 1-1 Installed Kit Parts

Page 12

CHAPTER 1 — INSTALLATION RELIEF PITCHER

° File

° Bandsaw

« Tape or glue

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Relief Pitcher kit serial number, part number, and description of the missing or damaged parts, and date received.

Preparing the Cabinet for the

Kit Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Figure 1-1 shows almost all kit parts installed in a typical cabinet. Use this illustration as a guide while you install the parts.

  • Turn off power to the game, and unplug the power cord.
  • Remove the following from the cabinet: ¢ Existing PCBs
  • Game harness, if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)compatible, Table 1-3 assumes you have an available game cabinet with a JAMMA harness installed in it.
  • Control panel decals, labels, and controls « Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals.
  • Video display (monitor) shield, display bezel, attraction shield, and marquee.
  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Assembling the Control Panel

Parts Needed from this Kit

To assemble the control panel, you need the control panel hole-cutting template. which is printed in Figure 1-3. Cut out the template sheet from this manual. You will also need the following parts from the kit:

  • Clear cover for the control panel © Control-panel decal © Start button assembly, snap-action switch, and “START” indicator plate
  • Sheet of control-panel labels ¢ Two joystick assemblies
  • Two pushbutton 3-color switches *¢ Twelve #10-24 x %"long black carriage bolts, flat washers, and nut/washer assemblies — four for the corners of the control-panel cover and eight for the joysticks

Installing the Parts

  • Using carbon paper, transfer the steering control mounting pattern from the template to the control panel. Save the template. Also refer to Figure 1-2 or 1-3 for the exact locations of all control-panel holes,
  • Using a saber saw, carefully cut out the large hole for the joystick controls and the smaller hole for the start button. Deburr the sharp edges with a file.
  • Lay the plastic cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the button holes as close as possible to the locations shown on the template. Lastly, mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes can be placed anywhere near the corners — wherever space permits. cS . Using a bandsaw, cut the control panel cover to its correct outside shape.
WARNING Wear safety glasses when drilling the plastic control panel cover. Use care to avoid shattering or chipping the plastic.
  • Tape or glue the template to the plastic cover. To start the saber saw cut, drill a 1/2" hole inside the joystick holes and the start button hole.
  • Saw out the large joystick holes and the start button hole.
  • Drill the four 4” holes that will be used to mount the cover to the control panel and the holes to mount the joystick controls and start button.
Page 13

Reuse Pircher @ CHAPTER 1 — INSTALLATION

Solder Side Component Side

Color’SignalPinPinnalColor’
BrownPOWER GNDA1POWER GNDBrown
Browr?POWER GNDB2POWER GNDBrown
Red+5V DCc3+5V DCRed
Red+5V DCD4+5V DC.Red?
Orange*-§VE5-5VOrange
Yellow®+12V DCF6+12V DGYellow
_—KeyHTKey_—
Violet/White*COIN CTR2J8COINCTR 1Violet/White’
—Not UsedK9Not Used_
WhiteSPKR -L10SPKR +Brown
—Not UsedM11Not Useda
GreenVIDEO GREENN12VIDEO REDRed
BrownVIDEO NEG. SYNCP13VIDEO BLUEBlue
—Not UsedR14VIDEO GND.Black
—Not Useds15SELF-TESTWhite®
OrangeRT COINT16LT COINYellow
_—Not UseduU17STARTWhite/Black
Yellow/BrownRT PLYR UP.Vv18LT PLYR UPWhite/Brown
Yellow/RedRT PLYR DOWNWw19LT PLYR DOWNWhite/Red
Yellow/OrangeRT PLYR LEFTx20LT PLYR LEFTWhite/Orange
Yellow/WhiteRT PLYR RIGHTY21UT PLYR RIGHTYellow
Yellow/GreenSWINGz22FAST BALLWhite/Green
Yellow/BluePOWER SWINGa23CURVE BALLWhite/Blue
Yellow/VioletBUNTb24SPECIAL PITCHWhite/Violet
_Not Usedc25Not Used_
—Not Usedd26Not Used—
Black/WhiteSWITCH GNDe27SWITCH GNDBlack/White
Black/WhiteSWITCH GNDf28SWITCH GNDBlack/White

1 The colors listed are for reference only. They are the colors used on the JAMMA harness available from Atari 2Connect to the SV GND (RTN) terminal on the power supply. However, if you have 12V GND, connect one of the wires at pin 1, 2, A, or B to the 12V GND terminai. 3Connect to the +5V terminal on the power supply. However, if your power supply has a + Sense terminal, connect to the + Sense. 4 Connect to the -5V terminal of the Power supply. If -SV is not available, connect to the 12V GND or the 5V Footnotes

GND. NOTE: If you do not have or use -5V, the maximum power to the speaker will be reduced by half. SConnect to the +12V terminal of the power supply. If your coin counter(s) “require 12V, also connect to the + side of the coin counter(s). Git you want to install a second coin counter, connect this wire to one side of the right 12V coin counter. Then clip R26 on the game PCB. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate. 7Connect this wire to one side of the left 12V coin counier. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate 8Use this wire if you want an external self-test switch. However, the kit already has a self-test swiich on the game PCB. {if you connect an exiernal seif-test switch, turn off the switch on the PCB. Connect the wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the switch to a GND wire.)

Table 1-3 JAMMA Pin and Wire Connections

Page 14

CuapTER 1 — INSTALLATION RFLIFF PITCHER

  • To prevent injury, carefully deburr all the edges of the plastic cover.
  • Install the control panel decal on the control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls:
  • Mount the two baseball batter decals on the control panel, around the joystick holes. Mount the circular decals around the three-button switch assemblies, and mount the two small instruction labels above the joysticks. Refer to Figure 4-2 for the correct placement of these decals. Install the cover on the contro! panel with the four 3/4"-long carriage bolts, washers, and locknuts. Nv Install the joystick controls using the 3/4"-long carriage bolts and #10-24 nut/washer assemblies.

w Install the start button assembly and the indicator plate as shown in Figure 1-1. For maintenance and servicing information on the joystick control, refer to Chapter 3 of this manual.

NOTE The four holes in the corners are not shown in this illustration. Drill these holes wherever space permits.

Connecting the JAMMA

Harness

  • If your game cabinet does not already have a JAM- MA harn install a JAMMA harness in the cabinet (optional, Atari part no. A046501-01).
  • Install one pair of square split beads on the harness that runs to the power supply, and the other to the harness the runs to the control panel. In both cases, make sure you move the split beads as. close to the PCB edge connector as possible. Hold the beads on the harnesses with the two tie wraps included in the kit.
CAUTION You must install the split beads on the JAMMA harness to meet FCC requirements.
  • Using Table 1-3 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.

1187" Dia

+ map \te mem oe porsof Suggestee stance trom ront of contro! panel, Chock 1.750" Da have sufeienr clearance before cuting holes 01,187" Dia, that the joystick eontrots 3.00" (2 places) (places)

Figure 1-2 Locations of Control Panel Holes to be Drilled

1-6

Page 15

RELIEF PITCHER % CHAPTER 1 ~ INSTALLATION

WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Relief Pitcher kit requires +5V and +12V. If -5V is available, it should be used, too. nv Tie off any other voltage wires on the power supply besides +5V, -5V, and +12V.
  • There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the power wiring does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, see Chapter 3 for alternative wiring.

Connect the wires clesignated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3.

Connecting Coin Door Wires

i. Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.

  • Connect one terminal of the door lamps to one of the GND wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
NOTE Do not use —5V for the coin door lamps. The -5V is required for audio.

Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply. Connecting the Control Wires - Connect the joysticks and switches to the JAMMA harness using crimp splices or butt soldering. Follow the wiring instructions in Table 1-3.

Grounding the Cabinet

Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of players, you must connect the green ground wire as indicated above.

Checking the JAMMA Connections

Before plugging in the game PCB, turn on the power to the game, and check for +5V on pins 3, 4, C, and D of the JAMMA connector; +12V on pins F and 6; and -5V on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Installing a Baseball Card Dispenser

To increase player appeal, this game is capable of accepting an optional baseball card dispenser. The selftest software has a special screen for setting several options related to a card dispenser. Contact your distributor to purchase a baseball card dispenser. Using any secure connection method, connect JPL4 pin 3 (CCNTR-R on the Game PCB) to the ENABLE signal from the dispenser. Note: The NOTCH signal from the dispenser is not used and can be left unconnected.

Connect the power and ground wires from the dispenser to the power supply, using the dispenser manufacturer's instructions. Refer to the supplement to this. manual (CO-376-01) for more information.

Installing the Relief Pitcher Board Set

After you have checked the power on the JAMMA connector (above), install the Relief Pitcher board set in

1-7

Page 16

CHAPTER 1 — INSTALLATION & REEF PITCHER

the cabinet. Follow these steps and referring to Figure 4-4:

  • Use the nylon standoffs and four #6 x 4" long screws in the kit.
  • Connect the JAMMA connector to the game PCB.
  • Secure the JAMMA harness away from the PCB with cable ties.
  • Turn on the power to the game. Check that the game PCBs function. If a video picture is not present, see Chapter 3.

Installing the Bezel, Decals,

Labels, and Attraction

Assembly

The bezel, decals, labels, and attraction assembly are shown assembled in a cabinet in Figure 1-1.

Installing the Display Bezel

Find the cardboard display bezel in the kit. This bezei can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required.

Installing the Product ID and FCC Label

Place the product ID label (part no. 038158-

  • and FCC compliance label (part no. 039450-01) on the back of the cabinet.

Installing the Side Panel

Decals

Find the side panel decals in the kit. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-1, Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Installing the Attraction Assembly

Find the Relief Pitcher attraction shield and the attraction panel film in the kit. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-1.

1-8

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings

Maximizing Earnings

For maximum earnings, regularly maintain your Relief Pitcher game following the instructions in Table 3-1, in Chapter 3. When you set up the game and when you collect money, perform the automated self-test and check the controls with the Controls Test in the self-test.

You should read Chapter 2, Self-Test, for information on the game options, statistics, regional settings, and coin options so you can effectively use the available options. Evaluate the game data by using the statistics and histograms screens, and make adjustments on the game options screen. The key to maximizing earings is striking a midpoint on game times. Game times must be short enough so that the player turnover is high. Conversely, game times must be long enough to give players a good value and ensure repeat play. Repeat play is crucial to longevity. The Relief Pitcher software gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjustments. One of the first settings you should make is the regional setting. To encourage regional rivalries, in the self-test select a popular city for each of the four Relief Pitcher teams. This game has 32 cities and regions to choose from. If collections seem low or are dropping off, check all player controls and coin mechanisms for proper operation.

If earnings seem low, the game is technically sound, and the average game time per quarter is under 150 seconds, try changing the game difficulty option to an easier setting. The change will give players more game time for their money.

If the average game time per quarter is over 270 seconds, first try changing the game difficulty to a harder setting. If the average game time per quarter is still over 270 seconds after a few weeks, try an even harder setting

Page 17

Rewer PrrcHer @& CHaeTer 1 — INSTALLATION

After changing the game difficulty settings, you should reset the game statistics and the histograms, The game statistics and histograms can be cleared in the self-test by holding the start button and pressing any left button.

Game Play

This section describes the features and play of the Relief Pitcher™ game.

Introduction

Relief Pitcher is timed with the opening of the 1992 baseball season. The famous sports announcer Jack Buck cails all the play-by-play, as players conirol the action from the best seat in the house — right behind home plate.

Relief Pitcher is a one- or two-player simultaneous baseball game kit for upright cabinets. Convols in this game include a start button, two joysticks, and two special “cluster” buttons to give players ultimate control and secrecy for strategy. Relief Pitcher has four ways to play:

  • One-player in a 24-game season with a Stars and Playoff game ¢ One-player in a 9-inning game vs. the computer
  • Two-player in a 7-game series ¢ Two-player in a 9-inning game Four different teams with a variety of strengths and weaknesses create incredible battles of strategy. Operators can even select which cities players can choose from. This way players anywhere in the country can relive regional rivalries. Players start with a minimum salary; they earn bonus dollars along the way for outstanding play. A new level of control gives players the ability to throw the widest variety of pitches in a coin-operated game. In addition to a traditional fast ball and curve ball, players can seject a sinker, knuckle ball, screwball, or rising fast ball as their special pitch. Players also can mix up speed by throwing hard or off-speed pitches. Players in the field can run and throw to all bases, hit the cutoff man, and even run down overly aggressive base runners. Batters can direct the ball by aiming the joystick towards left, center, or right field. Players determine if they want to bunt, swing, or “go for it” with a power swing. Base runners can even steal, stretch doubles into triples, and go for the “suicide squeeze.” For added game play and visual variety, the game has four different ball parks and one special Stars park. It’s like you're at the ball park as the home fans boo the visitors and cheer on their heroes.
Page 18

“RELIEF PITCHER

AM Centerline

* Figure 1-3 Hole-Cutting Template for Relief i

ATARI pice i Pitcher” Kit Control Panel (Left Side) |

GAMES

NOTE: Cut out this page and page 1-11 and overlap the centerlines (note there is

only one START button). Then tape the pages together and use as a

template. For more detailed information on hole-drilling refer to Figure 1-2. CHapter 1 — INSTALLATION

START BUTTON (1 place) fy | t

3-SWITCH | PUSH-BUTTON (2 places)

S JOYSTICK Tay 3 (2 places)

Page 19

g Centerline 5

Z Figure 1-4 Hoie-Cutting Template for Relief

z * Pitcher” Kit Control Panel (Right Side)

ci ATARI 2 GAMES é +

START BUTTON

t

3-SWITCH

PUSH-BUTTON

fit JOYSTICK Sean

Page 20

Cuapter 1 — Instattation @ Ritter PIfcHER

Page 21

CHAPTER 2

elf-

Test

INTRODUCTION

se the Relief

Pitcher” self-test

to check the con-

dition of the game circuitry

and controls. You will see

the self-test information on the video display

and hear the sound test information through

the speakers. You do not need any additional

equipment to perform the self-test. 8 You

should perform the self-test when you first set up the game, each time

you coliect the money, or

when you suspect game

failure. 8 This chapter

shows the screens in the

self-test and explains each of the tests. The

screens and explanations are arranged in the

order they appear in the self-test. Table 2-1

lists all of the self-test screens and their

purposes,

Page 22

Cuaprer 2 — SruF-Trst RELIEF PITCHER

Entering and Exiting

the Self-Test

To enter the self-test, tum on the self-test switch on the bracket located inside the coin door Gf you wired your kit that way). The Relief Pitcher Game PCB also has a self-test switch on it, near the edge connector. These two switches are wired in parallel, meaning that you can use either one independently. Exit the self-test by switching off any of the self-test switches.

Self-Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the SELECT TEST

Choose then press START

ADJUST VOLUME

GAME OPTIONS REGIONAL SETTINGS CARD DISPENSER OPTIONS COIN OPTIONS

SOUND BOARD TEST

CONTROLS TEST

RAM TESTS ROM TEST

ALPHANUMERIC TEST MOTION OBJECT TESTS PLAYFIELD TESTS list by pressing the left and right triggers; the corresponding test is highlighted in yellow. Choose the test by pressing the START button

Adjust Volume

Adjust the volume of the game using this screen, shown in Figure 2-2. Control the volume by moving the joystick right or left; the volume number increases or decreases. To restore the old volume level, push the

Screen ise or Purpose

Adjust Volume Adjusts the volume. MONITOR TESTS

Figure 2-1 Self-Test Menu Screen

right red button, Save the new volume and return to the self-test menu by pressing any left button.

Statistics Displays the game statistics. Use to set and check the game options settings. Game Options Regional Settings Use to set and check the city setting for each of the four teams.

Use to set the maximum number of cards per credit and how many bonus cards are dispensed after 9 innings. Card Dispenser Options

Coin Options Use to set and check the coin options settings.

Sound Board Test Use to check the audio circuits.

Use to display the functioning of the game switches. Controls Test

Use to check the program ROMs.

Use to test for clarity of characters.

Motion Object Tests Use to test the movement and color of game objects.

Playfield Tests Scrolling Test Stamp Test Use to check the playfield displays. Use to check the two video RAM chips. Use to check all the playfield stamps.

Monitor Tests Color Test Use to check the video display color circuits. Purity Test Use to check red, green, blue, white, and grey purity. Convergence Test Use to check and adjust display convergence.

Table 2-1 Summary of All Self-Test Screens

Page 23

ADJUST VOLUME

VOLUME = > mmm mmm mmm

Move Joystick to ADJUST volume

Press RIGHT RED Button to RESTORE old setting

Press Any LEFT Button to SAVE setting and exit

Figure 2-2 Adjust Volume Screen

STATISTICS Left Coins 1533 Right Coins : 1838 Aux Coins : 0 Idle Mins 9433 1 Player Mins : 3872 2 Player Mins : 42 Wasted Mins 15964 1 Player 9 inn. : 9487 1 Player season 3n2 2 Player 9 inn 9487 2 Player series 9487 chose BASHERS chose DUSTERS chose SPEEDERS chose STROKERS timeout PITCH timeout COACH Error Count

Total Coins

Percentage Plays Percentage Setup

Press Any Left Button for more stats

figure 2-3 Game Statistics Screen

Statistics

Use the information shown on the statistics screen, in Figure 2-3, and on the histogram screens to keep track of your game use and maximize your profits. Record the information on the Relief Pitcher statistics sheets in the back of this manual. The statisti e collected from the last time the statistics were cleared. You can clear the statistics by holding the start button and pressing any left button.

rror Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 14B on the Audio PCB. Rewer Prrcucr & CHAPTER 2— SeLe-TEST

Game Options

Check and select the game options on this screen, shown in Figure 2-4,

To move through the options, move the joystick up or down. Change the option in yellow type. The factory default settings are shown in green. To change a sctting, move the joystick left or right. To save the new settings, press any left button. ‘This returns you to the sclect test screen. If you want to keep the original setting, aithough you have changed it, press the right red button. This brings back the original setting.

‘The game option settings with factory defaults are e plained in Table 2-2

GAME OPTIONS

Restore Factory Default? Yes

‘Auto. fielding/running? No-Arcades

Reset High Score Table? No

‘Sounds in Attract? Yes

Free inning after victory? Yes

Game Difficulty? 4 - Hard ¢ MORE o@

Press RIGHT RED Button to RESTORE old Setting Press Any Left Button to SAVE setting and exit

Figure 2-4 Game Options Screen

Regional Settings

Check and select the regional game settings on this screen, shown in Figure 2-5. This screen lets you assign a city from the list shown to each of the four Relief Pitcher teams.

The list of available cities is displayed in the top half of the screen. Foliow the directions at the bottom of the screen to select the team and the cities.

Card Dispenser Options

To increase player appeal, this g apable of ac: cepting an optional baseball card dispenser. This screen has two options related to a card dispenser: one option sets the maximum number of cards per credit, and the other sets how many bonus cards are dispensed after nine innings. For more information on

Page 24

Cuaprer 2 — Seir-Trst % Reine PITCHER

OptionSettingsExplanation
Restore Factory Default? YesvNoClears high scores and sets options to defaults.
Auto fielding/running?No-Arcades¥—Yes-Tavernsif yes, the computer will run and throw for the player.

The “no” setting is suitable for high-skill players. The “yes” setting is suitable for low-skill players.

Reset High Score Table? NoYesWLets you clear the high score table.
Sounds in Attract?YesvwNoLets you choose whether or not to hear the voice of

announcer Jack Buck in the attract mode

Free inning after victory?YesvNoIn a “season” 1-player game, allows one free inning

after beating the computer.

Game Difficulty? 1-Easiest 2-Easy 3-Mediumw _ Establishes degree of game difficulty. 4-Hard 5-Hardest

Innings per creditlw23Sets the number of innings per credit.

v Manufacturer's recommended settings. These settings are shown in green on the screen.

Table 2-2 Game Option Settings

how to use these settings for maximum carnings, refer settings, press any left button. This returns you to the to the supplement to this manual, CO-376-01. select test screen. If you want to keep the original setting, although you have changed it, press the right red Coin Options button. This brings back the original factory setting. The coin option settings and factory defaults are explained in Table 2-3. Check and select the coin options on this screen, shown in Figure 2-6. To move through the options, move the joystick up or down. Change the option in yellow type. The factory default settings are shown in green. To change a setting, move the joystick left or right. To save the new

REGIONAL SETUP

Toronto Boston Detroit Cleveland Minnesota Chicago Kansas City California Charlotte

MilwaukeeNew YorkBaltimore
TexasOaklandSeattle

Honolulu Las Vegas, Louisville Philadelphia Montreal Atlanta Cincinnati Houston

MiamiDenverPhoenix
VancouverPittsburghSt. Louis
Los AngelesSan DiegoSan Francisco

Cincinnati Houston. COIN OPTIONS Free Play: No

Discount to continue: No Game cost: 1 Coin 1 Credit Bonus for quantity buy-in: None Right Mech Value: BASHERS in San Francisco 1 Coin Counts as 1 Coin DUSTERS Houston SPEEDERS in Los Angeles STROKERS In Chicago Left Mech Value: 1 Coin Counts as 1 Coin

Press RIGHT RED Button to RESTORE old Setting Press Any LEFT Button fo SAVE setting and exit Move stick UP or DOWN to select team Move LEFT or RIGHT to select cities

Press Any Left Button to return to menu

Figure 2-5 Regional Settings Screen Figure 2-6 Coin Options Screen

Page 25

Reuiee Price 4 CHAPTER 2

Option Settings Explanation

Free Play Now Yes Set this to “Yes” for demonstrating the game.

Discount to Continue Nov Yes Lets you offer a reduced price per credit when players want to continue a game.

Game Cost 1coin 1 credit

8 coins 1 credit Sets the number of coins required for one credit.

None 7 2coins give 1 (extra coin) 3 coins give 1

Bonus for Quantity Buy:

9 coins give 3. Lets you choose various levels of bonus coins or no bonus:

Right Mech Value 1 coin counts as 1 coin Y

1 coin count as 8 cains Is the number of coins each coin counts as in the right coin mechanism.

Left Mech Value 1 coin counts as 1 coin v

1 coin count as 8 coins ls the number of coins each coin counts as in the left coin mechanism.

V Manufacturer's recommended settings. These settings are shown in green on the screen.

Table 2-3 Coin Option Settings

Sound Board Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-7. Move the joystick left, right, up, or down to select the sound, and press the start button to listen to it. Pressing the right red button stops the sound from playing. Press any left button to return to the select test menu.

SOUND TEST

2345

1201301415

222325
323303435
424344«45
52535455
62636465
72737475
82838485
92939495
100 101103104 105

10 111 130114115

120121123124 125

SOUND #40

Press START Button to START sound Use joystick to SELECT Sound

Press Any Left Button

to return to menu

Figure 2-7 Sound Test Screen

Controls Test

The controls test allows you to display the status of the game switches and controls. The switch test screen appears in Figure 2-8. The items tested are:

¢ Joystick left, right, up, and down movement

  • All three switches in each “cluster” button

© Start switch

© Left and right coin switches

CONTROLS TEST

Press buttons and move joysticks

Start Button Yellow Button Start Button Yellow Button Red Button Red Button Green Button Green Button Right Right Left Left Down Down Up Up

LCOIN R COIN SERVICE

Press Left button and Start to return to menu

Figure 2-8 Controls Test Screen

Page 26

Cuaprer 2 — Seue-Test RLF PITCHER

© The auxiliary coin switch, if you installed one the correct words are highlighted in yellow on the screen As you activate each switch or control, make sur

To return to the select test menu, simultaneously press any left button and the start button

RAM Tests

Use this selection screen (shown in Figure 2-9) to choose which RAM test you want to perform. Use the different tests according to Table 2-4. If you have serious RAM problems, you may sereen, ee only a colored

Press the start button (and hold it, if the test is looping) to leave the individual RAM test and return to the Select RAM Test screen. Press the start button once more to return to the select te:

ROM Test

‘The ROM test (see Figure 2-10) checks the read-only memory. If the test passes, you will see the location and checksum of each ROM and the message All ROMS are OK. If a ROM is bad, the location of the bad screen

RAM TESTS

Choose then press Start

Video RAM (looping) Color RAM (looping) Working RAM (looping) All RAM (re-start) Exit RAM tests

Figure 2-9 RAM Tests Sub-Menu

Problem e of Test RAMs Tested

7K, 9K Playfield is erratic Video RAM or looks wrong, motion objects are not working properly, or game play is erratic or game is locked up

Colors look wrong. Color RAM SE, 6E

Table 2-4 When to Run the RAM Tests ROM TEST

os 56C0 3947

S: 4APR1992 12 MAIN: 4APR1992 12

Figure 2-10 ROM Test Screen

ROM is displayed. You need to replace that ROM.

Note: The OS (operating system) and program dates and times displayed in your game will be different from those shown in Figure 2-10.) P any left button to return to the select test screen.

Alphanumeric Test

The alphanumeric test screen lets you see the clarity of the characters, Figure 2-11 shows the first part of the alphanumeric test screen.

The screen displa all of the alphanumeric characters. If the characters are not clear, you have a problem. To scroll through the screen, move the joystick up or down. Press any left button to return to the select test

screen,

z m = ALPHANL

gas ? 8 8 s e 8 E R uw *

t u

a

u é c

* of O8\NOe HR a a A a H

a @

a Ne NEES P a oS © P ~ e m o-a40e 84g ge oerece

°

Figure 2-11 Alpha Test Screen

Page 27

Reet Pricer CHaprer 2 - Si

Motion Object Tests

The motion object test screen, shown in Figure 2-12, tests the movement and color of various game objects. Select the particular motion object test by pressing the rt button. The seven tests, in sequence, are as follows: © Move object position « Change picture stamp © Change object size

  • Change object palette © Toggle horizontal flip © Toggle object priority e¢ Change object number Within. each test, use the joystick control to move objects, change pictures, and change object size. Simultaneously press the start button and any left button to return to the select test screen.

Playfield Tests

Use the selection screen to choose which playfield test you want io perform — the playfield scrolling test or the playfield stamp test.

Scrolling Test

This test, shown in Figure 2-13, checks the condition of the scrolling playfield. Move the joystick left, right, up, and down to see the screen move accordingly. Press any left button to exit to the playfield test submenu

Motion Object Test

Figure 2-12 Motion Object Test Screen

Stamp Test

This test checks the condition of the playfield stamp circuitry. Move the joystick up and down to see the all the stamps displayed on the screen. Press any Icft button to exit to the playfield test sub-menu.

Monitor Tests

Use the selection ser you want to perform — the color, purity, or convergence test

Color Test

This test indicates the dynamic range of the video display color circuit. The color test s n to choose which monitor test

cen is shown in

Figure 2-14 Color Test Screen

be “I

Page 28

CHAPTER 2 — SeLF-Test @ Revick PITCHER

Figure 2-14. It should look as follows: white at the top, followed by red, green, and blue. The screen should also be black at the left, and pure color at the right.

Purity Test

This test indicates the purity of the video display color circuit in a series of five screens. Advance to each screen by pressing the start button: the software cycles through all five screens and then siarts over again. The screens are as follows:

  • Solid red
  • Solid green
  • Solid blue
  • Solid white
  • Solid gray If the screens do not match this description, adjust the video display as described in the video display manual. Press any left button to exit,

Convergence Test

The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-15. To see the violet and green screens, press the start button. Press any left button to exit Figure 2-15 Convergence Test Screen Check the following on the screens: ° The grid lines should be straight within 3 mm, and the lines should aot pincushion or barrel.

  • The convergence of the lines on the violet and white screens should be within 2 mm. If the screens do not meet these criteria, adjust the video display as described in the video display manual.
Page 29

CHAPTER 3

Troubleshooting and Maintenance

INTRODUCTION

his chapter contains on the printed-circuit boards,

troubleshooting ta- and a list of ROM-caused

bles and repair pro- problems, with specific ROMs

cedures for your Relief Pitch- to check and replace. ¥ The

er” game. The chapter has two parts. The first last part of the chapter has information about

part contains three troubleshooting tables. connecting the video display Cif it requires

The tables contain general troubleshooting separate positive sync) and repair information

information, the voltage levels and test points for the joystick controls.

Page 30

Carrer 3 — TROUBLESHOOTING AND MAINTENANCE Rrvier PITCHER

Pro

Coin Mechanism Problem Suggested Action

  • Check the wiring to the coin mechanism.
  • Check the voltage to the + side of the mechanism
  • Test the coin mechanisms with the controls test screen in the self-test.

Game Play Problem

  • Check the harness and connectors.
  • Perform tne self-test.
  • Check ihe voitage levels on the PCB. See Table 3-2, Voltage Inputs and Test Points.
  • Check What ROM Problems Look Like, Table 3-3, for specific ROM problems.

Control Problems

  • Check the harnesses and connectors.
  • Check the switches on the control.
  • If you took the control apart, have you reassembled it correctly?
  • Make sure all the parts on the control are in good repair. Repair or replace parts.
NOTE: The joysticks and three-button switches do not require lubrication

Sound Problem

  • Is the speaker volume turned up? (Volume is adjusted digitally in the self-test.)
  • Check the voltage on the JAMMA connector.
  • Check the wiring from the PCB to the speaker.
  • Check the voltage level to the PCB. See Table 3-2, Voltage Inputs and Test Points
  • Repiace the speaker.

Video Display Problem Screen is dark. Is the game plugged in? Is the game turned on? Are the connections good? Is the line fuse good? Is the display brightness turned up? Are the solder connections on the line filter and transformer good? Is the JAMMA connector on the PCB tightly connected? Check all of the items below. If you answer no to any question, you have a problem with the video display, not with the game circuitry. See your video display service manual a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have high voltage to the video display?

  • Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC, depending on the type of video display. Video signal voltage is 0.5 to 3.5 Volts.) 10.If the level is not correct, check the connectors and the harness. SPNADRWONA=

Only a colored screen appears. You probably have a serious RAM problem.

Display area wavers or Is too small,

  • Do you have correct power voltage to the video display PCB?
  • Do you have correct high voltage to the video display?

Picture is wavy.

  • Is the monitor ground connected to the monitor?
  • Are the sync inputs connected properly?

Picture is upside down When you serviced the display, you connected the wires incorrectly. Switch the horizontal or vertical yoke wires on the display.

Convergence, purity or Color problems. Use the screens in the self-test to adjust the video display. Use the adjustment procedures in your video display manual.

Picture is not centered. Use the centering procedures in your video display manual.

Table 3-1 Troubleshooting Table

Page 31

Rewer Prrciiex 4 CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

Voltage Test Point or LED Source and Purpose

+5 + 0.25 VDC +5V1 Logic power from the switching power supply. CR5 LED (Game PCB) Lights when 5 V is applied to the PCB and the reset (RST) jumper is open CR4 (Audio PCB) Lights when the +12 V supply is good. CRS (Audio PCB) Lights when the -5 V supply is good. Table 3-2 Voltage Inputs and Test Points on the PCBs

Problem ROM Causing the Problem Check the ROM at:

Program works, but motion objects orGraphics ROMs14S, 18S (Game PCB)

playfield is wrong. 4D, 8D, 10D (Audio PCB)

Garbage on screen; program doesn't work.Processor13F (Game PCB)
Game program is erratic.Program ROMs17E, 17J, 19E, 19J (Game PCB)
No sound or erratic soundADPCM ROMs9B, 10B, 12B (Audio PCB)

Table 3-3 What ROM Problems Look Like

Video Display Sync Problems

This game board provides separate positive horizontal and vertical sync on a separate connector, for monitors that will not work with the composite negative sync signal provided at the JAMMA edge connector. This connector (labeled “Sync”) is located near the edge connector. Pin 1 is horizontal sync, Pin 2 is vertical sync, and Pin 3 is ground.

Troubleshooting

The tables in this chapter (3-1, 3-2, and 3-3) can help you troubleshoot problems in your game. The troubleshooting table lists possible sources of problems in various parts of the game. The voltage inputs and test points can help you troubleshoot PCB problems. The ROM problems table can help determine exactly which ROM might be causing game play problems.

Removing and Replacing the Joystick Control

The joystick control is shown in Figure 4-2. If you have trouble with the joystick, make sure you have assembled it properly. Refer to the instructions included with the joystick or see Figure 4-2. If you need to repair the joystick, first remove it from the control panel. Disassemble it by removing the retaining ring at the bottom of the shaft. To replace any of the four switches, remove the two screws that secure each switch.

ROMs and RAMs

If you have think you have bad ROMs or RAMs, perform the ROM or RAM test in the self-test procedure. If you have a ROM problem, see Table 3-3. For the location of all the ROMs and RAMs on the game PCB, see Figure 4-4.

Page 32

CHAPTER 3 ~ TROUBLESHOOTING AND MAINTENANCE REUEF PITCHER

NOTES

= m/

Page 33

CHAPTER 4

Parts Illustrations

his chapter pro-

vides information

you need to order

replacement parts for your and the serial number of

your game. With this infor-

mation, we can fill your

order rapidly and correctly.

kit. Common hardware

parts, such as screws, nuts, washers, and so

on, are included in these parts illustrations.

  • When you order parts, give the part num-

ber, part name, the number of this manual, We hope this will create

less downtime and more profit from your

games. Atari Games Customer Service phone

numbers are listed on the inside front cover

of this manual.

Page 34

Cuarrer 4 — Parts ILLustrations Revirr PrrcHre

171099-001 &-Position Gold- Contact Joystick Assy. (2 places) 75-5112B #10 Camage Bolt 178237-004 White Button Assy. 160044-001 Snap-Action Switch 178283-011 049965-01 Bezel Wi Graphics 178056-002 1/2" W. x 1/16" T. Foam Tape (2 pieces, 2" tong)

(8 places) 175014-1040 #10 Flat Washer (8 places) 177010-240 #1024 Lock/Nut (places)

049964-01 Contro! Panel Decal 047209-01 Control Pane! Cover

171104-001 Gold Contact Pushin. Switch Assy. (2 places) (049967-01 Control Panel Label

7551128 #10 Carriage Bolt (4 places) 175014-1040 #10 Flat Washer (4 places) 177010-240 #10-24 Lock/Nut (4 places) —— 047205-01 7 Attraction Shield

049963-01 Attraction Film

'049962-01 Side Panet Decal (2 Places)

‘8050247-01 Board Set Assy. consisting o: A049727-03 elie Pitcher Game PCB Assy. ‘A050135-01 Relief Pitcher Audio EPROM Assy. ‘A050279-01 60-Gircuit PCB Ribbon Assy 034536-12 Foam Vibration Damper 178265-001 LSiyie Nylon. Standolt 4 Places) 72-6608S #6 x 172" Pan- Hd, Screw (4 Places)

Figure 4-1 Parts of Relief Pitcher Universal Kit A04960-01 A

Page 35

RELIEF PITCHER & CIIAPTER 4 ~ Parts ILLUSTRATIONS

049967-01 Control Panel Label

(Pitcher Label) (Special Pitch, Curve Ball, Fast Ball Label) (Batter Label)

171099-001 | 8-Position Gold- Contact Joystick Assy. (2 places) 75-5112B #10 Carriage Bolt (8 places) 175014-1040 #10 Flat Washer (8 places) 177010-240 #10-24 Lock/Nut Drawer Assy. (Pitch Location label) (Blunt, Power Swing, Swing Label) (High Swing, Level Swing, Low Swing Label)

4 | 75-5112B #10 Carriage Bolt (4 places) 175014-1040 #10 Flat Washer (4 places) 177010-240 : < #10-24 Lock/Nut 047209-01 : (4 places) Control Panel Cover :

050294-01 Control Panel 049964-01 178237-004 Control Panel Decal Bale euten Assy. Items Not Shown: 171104-001 160044-001 ‘Snap-Action A050192-01 Gold Contact P PB Switch Assy. Switch Control Harness Assy. (2 places) 178283-011 START Indicator Plate

Contro! panel in closed position

Figure 4-2 Control Panel Parts

Page 36

Cuaprer 4 — Parts ILLUsTRATIONS @ RELIEF PITCHER

99-215030 } Black Knob and Shaft

___| 99215032 Washer

99-215031 | Pivot Cylinder

99-215018 Spring 1* Diameter

99-215035 Z-Stop

99-215011 #8 x.75 Screw (4 places) — _| 160044-001 -187 Microswitch A I 99-215010 #4 x75 Screw (8 places)

99-215036 | __ Microswitch Actuator

99-215031 Pivot Cylinder

Figure 4-3 8-positlon, Gold-contact Joystick Assembly 171099-001

Page 37

Reuer Prrcier & Cuaprer 4 — Parts ILLusrRaTIons

a, a8, ° n,n 9) a Ho =e = nie Ly me x eon Ses) feet ents 197670-085 b mmancm | , OC as 197598001 ‘yO

QD sr) seme e006

8] BO. ses) z2=es09e1

Figure 4-4 Relief Pitcher Game PCB Assembly A049720-XX H

4-5

Page 38

CHAPTER 4 — Parts ILLUSTRATIONS & RELIFF PITCHER

ose 196099-xx08 (3E)

ra403

° *e 8 R10 32 cig cz0 0 79.8273 2 13403 eg 136098-2209 (A) 5 Drums | "RF 8 | azegeze ehaaias at

g 8 “ _mser3 Gi Ox 1 OTL 3 hh

THETH orany 196098-2%20 (9B)

rws74

2 7a 874 é 4 © cuz 148 02 705374 Q) momma | B > 136093-xx10 (15a) 0 140 o* ° 3at $9TS The

oT

“REESTAL ST ht €T 2T TT

Figure 4-5 Relief Pitcher Audio PCB Assembly A050134-XX B

Page 39
Scan of page 39

This page is a drawing, shown as the original scan.

Page 40

CHapTER 5 — SCHEMATIC DIAGRAMS inp PITCHER

coo? oo? co) cw Tr cote wey coo) cc-LoceL) CPR AUD > ‘crea? cee) cv GO) cSELFTEST> coon estran.a cUPLAD COOMAD uernAd cRIGITLAD cupurrona) cupurroz) cupurTona) arent wet 0.00 awe2 000 are-3 Oa ov wrre-s oy oReR-3 Oo weere-§ Oo ot Pee? O- BemA-8 0 conte, IPA OsReP8-10 oO —— spree, SReee-11 0s aun ameen-12 0s ae ‘Sreve-13 0———s ue, JReR-19 0O——$. G0 ‘sere-13 os serves ‘Sreve-16 0» coin. Sreen-17 o——— greta ‘sreve-18 Os uP ‘Sreve-13 0+ ons ‘Sreve-20 0a Fs ‘srewe-21 Oo R13 ‘Drere-22 0a Fines srewe-23 0 pcTAL ‘eeve-25 0 PTL CLEFTLBD 3RePR-25 O- CRIGITLBD JAePR-26 O- COND? JAR-27 0-00 COO) JaPA-28 0O———* nO

5-2 snc 1 o—evesrec.ouT 2 o—eysrnc.ouT 20 —-oo too) coo? cow) cw cw cae) ney cconree ce-Locar) ‘csPuei-> cau OD) CCREEND csmca csenvice> enn) coma cSTARTRD ‘CUPRRD oman? cLerteAd cRicwTRAD cROUTTON CRBUT TONE > CRBUTTON > sare ‘CLEFTRED crIcwTas) (oo? com>

Page 41

RELIEF Prrcher “ CHAPTER 5 — SCHEMATIC DIAGRAMS

Vre

ow!

‘SPARE CATES

Figure 5-1 Relief Pitcher Game PCB Assembly Schematic Diagram 049726-01 H

Page 42

Cuarrer 5 — Scuemaric DiaGraMs “Rewer PITCHER

~ oco:18

rcrez cro acraa sca Fines. ries starz aura SSSESKES°O

scrom acres scree actaa ries Fine = stats et sane—t tenteproe tem ton Oe] TTT TET 3

  • ws TREMBEM EDEN ETE st ‘s
  • eu on eae %
  • Bie on = oe Fra a 2
  • ae Bd TsesT ori we 7 oe re means ide or ters _ Hele ar a aT HS low aa He
  • z ws = ca cae a
  • Hele alee =

STEERING ware | TReKerL

U3 | noRZ PLS

VERT PLZ, VERT PLL voRZ PLZ WORD PLL fas

Page 43

Rewer Prrciier & CHaprer 5 — SCHEMATIC DiaGRaMs

ate

a G2 a

2T0R

eTMc.cUT

a3[ pt oes n23 Tete ‘os ie 2 [ot t 2 ven. OUT oe de: d 2 os be oor TTooerr 7 itoorr eo Tr

istansetide | vet porte] Ls ry eyes est faust =| rmorue— feat vaen-s fie patois e—2fan__ev a2 oF grit 0% ic Ss a soa

Ey

7 0s

Figure 5-1 Relief Pitcher Game PCB Assembly Schematic Diagram 049726-01 H

Page 44

Cuarter 5 — Scnematic DiaGRaMs @ RELIEF PITCHER

on moto ote ms ot. renrr oie o oer cad cfm a ome o iy ot sor oLamu ole ot of permit oan ott oioe ote o coo une

”

| arcs ‘ Poe oo

= ot Bias FE roe

OR ox NO ANDO ACNO TIED INTERNALLY NEAR MSM629S. ou Mar

5-6

Page 45

RELIEF PITCHER CHAPTER 5 — SCHEMATIC DIAGRAMS

or or —8fegsalt* —e crane

oeOero 4g tap t—e xe
930siw"saltDEE
Eam20ama
340alod
oeot3130sabeme
aoa0
0onx0to rears:

SS om isers ats or west wx

Figure 5-2 Relief Pitcher Audlo PCB Assembly Schematic Diagram A050134-XX B

5-7

Page 46

Chapter 5 — SCHEMATIC DIAGRAMS RELIEF PrTCUER

J a late ore ee fd PHOS aia] fas

at x es wen 5 (At 19 [a7 va a =e wat — 26, win 20 [AP

2 sasae errs
g teevar — 5)bf
omvee 6crsaH

22 oR se

go Rosvm oimOS

co

be SECSa+me
ptimB 2 Gro7ett
B susvatawaitOt
xeiwotOL

vss ett] ont “tee” Te ee Fy,

  • soar . Dd wort J ez few OT oo oo

5-8

Page 47

Reur Pitciter ¢ CHAPTER 5 — SCHEMATIC DiAGRAMS

aay

at a * ca jsoopr $i SN Ban Ni ar 2 wo x pie a ht a Pe Rit wag ae x, irre oes oe a FS ,

ons sank aan aX, ALS oz Py 813 oes eae = Rie 33 ci3 mE at ie aoe 2)

uy or H Li conese? ie or Se Yeo bse oe a text

Figure 5-2 Relief Pitcher Audio PCB Assembly Schematic Diagram A050134-XX B

Page 48

Cuaprer 5 ~- SCHEMATIC DIAGRAMS RELIEF PITCHER

5-10

Page 49

AN

ATARI

Relief Pitcher Kit Statistics Shee

Date Recorded: Location:

Meter:

1st Screen — Statistics Left Coins Right Coins Equivalent Auxiliary Coins Hours : Mins. Idle Minutes 1-Player Minutes 2-Player Minutes Wasted Minutes 1-Player 9-inning game 1-Player 24-game season 2-Player 9-inning game 2-Player 7-game series Chose BASHERS Chose DUSTERS Chose SPEEDERS Chose STROKERS Timeout PITCH Timeout COACH Error Count LIT TLT TL

Total Coins

Percentage Play Percentage Setup

Page 1

Page 50

JA

ATARI

GAMES

Relief Pitcher’ Kit Statistics Sheet

Date Recorded: Location:

Meter:

2nd Screen — Statistics for Each Player Position

Coins Total

Used Minutes Average

1-Player NEW 1-Player CONT

ayer NEW ayer CONT

3rd Screen — Performance Statistics

Avg At Bats Slugging % Hits Total Bases Runs Scored Homers Triples Doubles Walks Sacrifices Pitches Thrown Strikeouts Runs Allowed Allowed Hits Walks Given Up Batters Hit Hitters Faced Outs Made Double Plays ERA Pitch/At Bat

Page 2

Page 51

PeE EEE eee ee ee see ele eller!

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a , period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and (©) Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

PPP eee ee eae ee eee leet elle

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than, Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 52

A.

ATARI

GAMES

ATARI GAMES CORPORATION 675 Sycamore Drive Milpitas, CA 95035