Stompin' (M051-00e38-B014)
Stompin' (4/4/86) (Bally/Sente, 1986) · Manual · 22 pages · 13 sections · original scan
Stompin’ game review
Please disregard Self-Test and Attract Mode information shown on page 6 of Bally Sente Field Conversion Kit Manual (M051-00C47-A019). Refer to information on this page instead.
After installing the STOMPIN' game in your SAC 1 unit, check the game as follows:
Self Test
- Power on game. If title page of game appears, switch on Self-Test function by moving Self-Test switch located on the electronic chassis between the sound board and the game cartridge.
- RAM and ROM Test should appear on screen (Screen 1). If RAM and all ROMs are working correctly, the test will show an "OK" next to them. If any are bad, the word "BAD" will appear on the screen.
- At the conclusion of the RAM/ROM Test, the Sound Board Test will occur (Screen 1). If the board tests out, advance to the next test mode by pressing the ZAPPER button.
- The next test mode is the Switch Input Test (Screen 2). Test all switches except the ZAPPER. If the correct word lights up on screen when a switch is closed, the switch is working correctly. Test coin mechancisms. If everything is working correctly, advance to next screen by pressing ZAPPER button.
- The next test mode is the Coin Option Settings (Screen 3). The STOMPIN' game has the European coin mode options. See "Option Switch Settings"Sheet regarding the setting of European coin mode options. Press ZAPPER button to advance to next test mode.
- The next test mode is the Game Options (Screen 4). The game features controlled by these option switch settings are self explanatory. Press the ZAPPER button to advance to next test mode.
- You are now in the statistics mode. A series of three (3) screens display information, in bar graph form, since the last time the statistics were reset. Screen 5: Game Score Stats: Time Distribution Screen 6: Game Score Stats: Level Distribution
- Screen 7: Game Score Stats: Score Distribution Press ZAPPER to advance through the screens! Press START to clear and reset the statistics. Move the Self-Test Switch to return the game to Play Mode.
- Please note: After Screen 7 is displayed, pressing ZAPPER will advance through Screens 5, 6, and 7 again. To break from this recycling, move the Self-Test Switch to return the game to Play Mode.
Play Mode
- Title screen will appear.
- Instruction screen will appear.
- Game demonstation will be displayed.
- Credits screen will appear.
- High score table will appear.
- Missing kids page will appear.
M051-00E38-B014
Game Description
STOMPIN' is a game which will challenge you both mentally and physically. In this game you, the player, are given the task of preventing various bugs and critters from eating away the food located at the center of the screen. You do this by stepping on the FLOORPLAY controller, each section of which corresponds to one of the sections surrounding the food on the screen. When stepping upon a section that is occupied by a bug, that bug is squashed and you have successfully kept him from the food. The game is over when all the food is gone.
The game consists of three (3) distinct environments. Each one contains its own set of "critters" and levels of increasing difficulty as shown in the following table.
EnvTronment
Round Level Displayed on Screen Critters
chen Floor jeese nts
in Center Square
| 2 | 2 | Ants & Cockroaches | |||
| * 3 | 3 | " | . | . | Ants, Cockroaches & Mice |
| * 4 | 4 | : | " | " | Ants, Cockroaches Mice & Spiders |
| * 5 | 5 | Patio W/Hot Dogs on | Gophers |
Barbecue Grill in
Center Square
| 6 | 6 | " | ° | 7 | Crows |
| 7 | 7 | " | " | " | Gophers & Crows |
| 8 | 8 | Pond W/Small Flies in | Slow Frogs | ||
| * 9 | 9 | " | . | 7 | Slow Fish |
| * 10 | 10 | - | " | “ | Fast Frogs |
| * il | ll | 4 | " | » | Fast Fish |
After Round 11 ends, the succeeding rounds will repeat the same level of difficulty, (Level 11).
- NOTE: By using a Game Option Switch, a bee will appear in various rounds. If the bee is squashed during a round, a bonus of 2000 points are awarded. Also, all of the other critters will be killed automatically with their point values added to the score and the round ends.
M051-00€38-B014
=
OPTION SWITCH S STOMPIN'
ETTINGS - DIP SWITCH
TITITITTTTTTTTTTTTAT ALT T ATT TT 1111 NARYOUS GAME PLAY OPTIONS ////////////ITTITITTITITTTI LL
* MISSING KIDS DISPLAYED MISSING KIDS NOT DISPLAYED OFF XX ON XxX
KID ON RIGHT NOT LOCATED KID ON RIGHT WAS LOCATED OFF ON
KID ON LEFT NOT LOCATED KID ON LEFT WAS LOCATED ON
ATTRACT SOUND PRESENT ATTRACT SOUNDS ABSENT OFF ON
* NO BEE PRESENT BEE IS IN GAME
NO BUGS (For Floor Demo)
BUGS PRESENT (Regular Play)
INDICATED FACTORY RECOMMENDED SETTINGS PART NO. MO51-00E38-A007
OPTION SWIT CH STOMPIN'
SETTINGS
- DIP SWITCH “Hi"
TIAITTLTAT TTT AT TL COINS PER CREDIT /////LTISTITTITLTITTATITT TTI TLTT A
VARIOUS CREDIT OPTIONS
FREE PLAY
- 1 COIN / 1 COIN / 1 CREDIT 2 CREDITS 2 COINS / 1 CREDIT 3 COINS / 1 CREDIT SWH1 SW#2 SWH3 SW#4 SW#5 SWH6 SW#7 SW#8
OFF OFF OFF OFF OFF OFF OFF OFF ON ON OFF ON ON OFF OFF OFF
TUITITTTTTTT TT TTTTATTTTAT TTT L171 COINS ADD BONUS COINS //////TIIITITTITITIVITTTITITITT TT
| * NO BONUS COINS | ON | ON ON |
2 COINS ADDS 1 BONUS COIN OFF ON ON
| 3 COINS ADDS 1 BONUS COIN | ON | OFF ON |
4 COINS ADDS 1 BONUS COIN OFF OFF ON
| 4 COINS ADDS 2 BONUS COINS | ON | ON OFF |
5 COINS ADDS 1 BONUS COIN OFF ON OFF
| 5 COINS ADDS 2 BONUS COINS | ON | OFF OFF |
5 COINS ADDS 3 BONUS COINS OFF OFF OFF
TTT TTT ATTA TTT COUN MECH MULTIPLIER /////// 11/111 IITA
- LEFT COIN MECH X 1 LEFT COIN MECH X 2
- RIGHT COIN MECH X RIGHT COIN MECH X RIGHT COIN MECH X RIGHT COIN MECH X ON OFF
oN OFF ON OFF ON ON OFF OFF
- INDICATED FACTORY RECOMMENDED SETTINGS PART NO. MO51-00€38-A007
KIT PARTS LIST: STOMPIN' U.R. PART NO. GE38-00001-0000
ORDER BY PART NUMBER ONLY
tren PART NO. | DESCRIPTION 1 | AE38-00004-0000 [CONTROL SHELF ASSY.
AE38-00005-0000 |CONTROL SHELF CABLE ASSY.
BO06-08029-010B |FLOOR-PLAY INTERFACE BD. ASSY.
U570-00042-0200 |SWITCH: SW., SPST., 1A, 125VAC - RED
OE38-00100-OOXF |PANEL: CONTROL SHELF SCREENED
| 0E38-00101-0000 |BRKT: INTERFACE SUPPORT 0E38-00700-00XF |END: GRAB BAR (2 REQ'D.)
0£38-00701-0000 |TUBING: GRAB BAR
0E38-00901-0000 |CUSHION: GRAB BAR
0017-00032-0092 |SWITCH: SPDT P.B. MOMENTARY, LED.
0929-00905-O0XF |BEZEL: SWITCH
2 AE38-00007-0000 |FLOOR ASSY.
3 AE38-00009-0000 |CABINET MOUNTING PLATE ASSY.
0E38-00108-0000 |PLATE: CABINET MOUNTING
0017-00103-0013 j|NUT 10-32 WELD (2 REQ'D.)
4 AE38-00014-0000 |BAG & HARDWARE ASSY.
0017-00101-0760 |10-32 X 16 PHILLIPS ROUND WASHER HEAD SCREW (2 REQ'D.)
0017-00101-0807 |5/16-18 X 12 UNSLOTTED HEX HD. STOVE BOLT (2 REQ'D.)
0017-00102-0045 |3/8-16 X 12 UNSLOTTED HEX HD. STOVE BOLT (2 REQ'D.)
0017-00104-0103 |WASHER: FLAT .390 1.D., .625 0.D., .031 TH. (2 REQ'D.)
5 AE38-00300-0000 [= INSTRUCTION ASSY. MO51-00E38-A007 |TAG: OPTION SWITCH SETTINGS
M051-00C47-A019 |MANUAL: CONVERSION KIT
6 AE38-00301-0000 |GAME INFORMATION SHEET ASSEMBLY: STOMPIN' U.R.
r MO51-00E38-A014 |GAME REVIEW SHEET: STOMPIN'
M051-00E38-A015
KIT PARTS LIST: STOMPIN' U.R., CONT'D. PART NO. GE38-00001-0000
ORDER BY PART NUMBER ONLY
TTEM I PART NO. DESCRIPTION
MO51-00E38-A015 PARTS LIST: STOMPIN' U.R.
MO51-00E38-A017 FLOOR-PLAY ASSY.: INSTALLATION PROCEDURE
M051-00E38-A007 OPTION SWITCH SETTINGS SHEET
M051-00E38-A018 FLOOR-PLAY ASSY.: PARTS ILLUSTRATION SHEET tt
M051-00E38-A019
M051-00E38-A017 PARTS LIST: FLOOR-PLAY ASSY.
FLOOR-PLAY ASSY.: INSTALLATION PROCEDURE
M051-00E38-A016 CONTROL PANEL & FLOOR PLAY ASSY. WIRING DIAGRAM: STOMPIN' U.R.
MO051-00C47-A003 SAC 1A WIRING DIAGRAM
M051-00E19-B003 SAC 1B WIRING DIAGRAM
M051-00E23-A005 SAC-MAN WIRING DIAGRAM
COMPONENT LAYOUT & PARTS LIST: 256K CARTRIDGE BD. [ene M051-00114-A149 SCHEMATIC: 256K CARTRIDGE BD. 11 | M051-00E38-B012 COMPONENT LAYOUT & PARTS LIST: FLOOR-PLAY INTERFACE P.C.B.
M051-00E38-B013 SCHEMATIC: FLOOR-PLAY INTERFACE P.C.B.
M051-00E38-A010 PARTS LIST: FLOOR-PLAY LAMP BD.
M051-00E38-A011 SCHEMATIC: FLOOR-PLAY LAMP BD.
7 A084-91834-AE38 |PROGRAMMED 128K CARTRIDGE W/SECURE
8 U858-00632-U802 |6-32 X 8 SOC BUTTON HD. SCREW
9 0£38-00900-0000 |HEADER: GRAPHIC "STOMPIN'"
10 0017-00103-0052 |NUT 6-32 LOCKING (9 REQ'D.)
MO51-00E38-A015
MOUNTING PROCEDURE FOR FLOOR PLAY ASSEMBLY TO UPRIGHT GAME CABINET: SAC 1, SAC 1A, SAC 1B & SAC-MAN (PAC-MAN, GALAXIAN, MS. PAC-MAN, TRACK ‘N' FIELD, & HYPERSPORT)
For SAC 1A, SAC 1B, & SAC-MAN qame cabinets: Remove rear door and lay cabinet on its side. Drill 2" hole in bottom of cabinet as shown in Figure 1. For SAC 1 game cabinet only: Remove rear door and notch it as shown in Figure 1A. Lay cabinet on its side.
With cabinet still on its side, attach Cabinet Mounting Plate to front leg leveler mounting holes using two (2) hex bolts * and two (2) washers provided with kit (see Figure 2).
- NOTE: For SAC 1: 5/16"-18 X 3/4" unslotted hex head stove bolt & for SAC 1A, SAC 1B & SAC-MAN: 3/8-16 X 3/4" unslotted hex head stove bolt.
Stand cabinet upright. Run cable of Floor Play Assembly thru slot in Cabinet Mounting Plate (see Figure 3). For SAC 1A, SAC 1B & SAC-MAN game cabinets: Feed Floor Play cable into cabinet thru 2" hole in cabinet bottom (see Figure 3). For SAC 1 game cabinet only: Run Floor Play Cable under cabinet to its rear and bring cable into cabinet thru rear opening where rear door notch is located (see Figure 2). For all game cabinets, position Floor Play Assembly over nuts welded on Cabinet Mounting Plate and fasten with two (2) 10-32 X 1" phillips round washer hd. screws provided with kit.
Run Floor Play cable up inside wall (either side) of cabinet. Secure Floor Play cable to wall using 3/4" wire harness clamps provided with kit. Connect Floor Play cable connector Jl to P2 connector of Control Interface P.C.B. mounted on Control Shelf Insert (see Figure 3).
Secure rear door to game cabinet.
M051-00E38-A017
MOUNTING PROCEDURE FOR FLOOR PLAY ASSEMBLY TO UPRIGHT GAME CABINET: SAC 1, SAC 1B & SAC-MAN (PAC-MAN, GALAXIAN, MS. PAC-MAN, TRACK ‘N’ FIELD & HYPERSPORT), CONTD.
CABINET BOTTOM
FRONT OF CABINET
—— DRILL 2" DIA. HOLE
LEFT SIDE OF CABINET
FIGURE 1
INSIDE OF REAR DOOR
SAC 1 CABINET ONLY: NOTCH REAR DOOR AS SHOWN.
FIGURE 1A
MONK 4-nnE 2a Antz
MOUNTING PROCEDURE FOR FLOOR PLAY ASSEMBLY TO UPRIGHT GAME CABINET: SAC 1, SAC 1B & SAC-MAN (PAC-MAN, GALAXIAN, MS. PAC-MAN, TRACK ‘N’ FIELD & HYPERSPORT) , CONTD.
CABINET BOTTOM
FRONT OF CABINET ————>
i
CABINET MTG, PLATE
FLAT WASHER
(a BOLT LEFT SIDE OF CABINET
FIGURE 2
| FLOOR PLAY FRONT OF CABINET—>! CONNECTOR J1
SECURE FLOOR PLAY CABLE OF FLOOR PLAY WITH TWO (2) 3/4” WIRE- INTERFACE P.C. BD. HARNESS CLAMPS TO LEFT ON CONTROL SHELF OR RIGHT CABINET WALL. INSERT {ee P2 CONNECTOR
10~32 X 1” PHL. ROUND WASHER HD. SCREW HED et FLOOR PLAY
(2 REQ"D.) CABLE
FLOOR PLAY CABINET ura, —/ ASSY. PLATE
FIGURE 3
M05 1-00E38-A017
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
FLOOR-PLAY ASSEMBLY PARTS LIST AE38-00007-0000
ORDER BY PART NUMBER ONLY ITEM PART NO. DESCRIPTION 1 | AE38-00006-0000 [estan ASSY. (27 REQ'D.) arenes LENS, CHANNEL & LED 9-15/32 (6 REQ'D.) (INCLUDES ITEMS 2, 3 & I 2 | v006-08028-010A ~
U007-08028-010A FLOOR CONTROL LAMP BD. ASSY.
FLOOR CONTROL LAMP P.C. BD.
U550-00086-0100 CONNECTOR KK100 PCM MO2A: SQUARE TIP
100E-00005-0035 120 OHM 1/4W RESISTOR
119E-00001-0007 L.E.D.: RED MV5760 (4 REQ'D.)
0E38-00102-0100 [enn LENS | 0017-00101-0518 5-40 X 5 PHILLIPS PAN HEAD M.S.
AE38-00011-0200 LENS, CHANNEL & LED 10-23/32 (6 REQ'D.) (INCLUDES ITEMS 2, 4 & 5)
5 0E38-00102-0200 |CHANNEL: LENS
6 AE38-00012-0000 |PAD ASSY. W/TAPE ASSY. (9 REQ'D.) ~
7 | AE38-00013-0000 |FLOOR-PLAY CABLE ASSY. (NOT SHOWN) 8 0E38-00103-0000 |WASHER: SQUARE (4 REQ'D.)
9 0£38-00104-0000 |DIVIDER: CENTER (2 REQ'D.)
10 0E£38-00105-0000 |DIVIDER: HORIZONTAL (2 REQ'D.)
ll 0E38-00106-0000 {DIVIDER: END (4 REQ'D.)
12 0E38-00107-0000 |COVER: END
13 0E£38-00109-01XF |BASE-FRAME: L = 34.781 (2 REQ'D.)
14 OE38-00109-02XF |BASE-FRAME: L = 31.031 _| 15 OE38-00110-OOXF |BASE-FRAME: FRONT
16 0E38-00501-0000 |BASE: FLOOR-PLAY ASSY.
17 0E38-00902-0000 | INSULATOR: TAPESWITCH (54 REQ'D.)
M051-00E38-A019
FLOOR-PLAY ASSEMBLY PARTS LIST CONT'D. AE38-00007-0000
ORDER BY PART NUMBER ONLY
| ITEM PART NO. | DESCRIPTION 18 0E38-00904-0100 {LENS: L = 10.968 (6 REQ'D.)
19 0E38-00904-0200 LENS: L = 9.718 (6 REQ'D.) | 20 0017-00101-0337 5 X 8 PHILLIPS PAN HEAD SCREW (16 REQ'D.)
21 0017-00101-0117 8 X 10 PHILLIPS TRUSS HEAD SCREW (4 REQ'D.) 22 | 0017-00101-0684 10 - 32 X 16 HEX SOCKET FLAT HEAD SCREW (24 REQ'D.)
M051-00£38-A019
AH/GRN. © START 9 MHZ BLU © ZAPPER BLK
270 tse aa vst ZAP LAMP |
BLK
GRN FLOORPLAY INTERFACE P.C, BOARD B006-8829-810B WH BLK
WHRED
WHT
k FLOORPLAY INTERFACE P.C. BL
CONNECTS TC
Jt FLOORPLAY CeBLE CONNECTOR CONNECTOR (51>
FOR P2 PLC.B, CONNECTOR PIN-OUT THFORMATION, SZFER TO FLOORPLAY INTERFACE P.C.5. SCHEMATIC.
GRY-BRN SRY-GRN BRN GRY
BLU-GRN
GRN-YEL.
H-RED
GRN-HHT
y-0
YEL-BLU
tH La tw
ta
Le
Lr
Lp Lt Lx ub
FE * * :
aL GAME CABINET
9 FOOT SHITCH ASSEMBLIES
sree sFet sree Y-BLU Y-BRN Y=0
SFit 6-¥
sree SF2t 6-8 WHT
TYPICAL FOOTSWITCH ASSEMBLY "SF19"
{pLu-u NOTE: EACH FOOTSHITCH ASSEMBLY joo
+1av
TO Six PIN P
EXAMPLE:
® LH» LED LAMP P.C.B, AT LOCATION “H* u006-ase28-01¢0
EDGE CONNECTOR NOT KEYED? PIN 1 OF P2 CONKECTS TO PIN t OF Ji. DRIVER TO Sir PIN 12 CONSISTS OF 3 TAPESHITCHES,
TO J1/PIN U
SWITCH RETURN GND TO JisPIN 1
EXAMPLE: ‘#8 SFIO= FOOT SUITCH AT LOCATION "18"
TAPESHITCH! AE38-a9026-2000
HAYNE STONE 479786 BALLY MIDWAY HFG. CO.
STOMPIN U. Ry CONTROL PANEL & FLOORPLAY ASSY. WIRING DIAGRAM NO51-00£98-A016 [SHEET i or 1 [Revs |
ORN ‘ORN +54 +5) WHT 15¥ +5V_ SENSE WR
fac sense GRY POWER SUPPLY B@a6-08009-1008 RED
12V_ UNREG 12V_UNREG wD rT ee oF Ol
12¥ 1@COIN DOOR LIGHTS 3 5
| WHT ev | 14 | " |
@BLK 1154 pig 1° : 16 Roe
| ea | 3 if | Ju4 | ||
| POWER CHASSIS ASSY | HONITOR | y | ni | 12¥ 1 COIN METER |
| AC4?-90009-0008 | rl | to | IE 4 | |
| FLUORESCENT LIGHT | a | { | i | GND al GROUND |
i is H !
| SPEAKERS | be. | wo |
iz = is aa Sasue6}+ COIN @ H 4 79 S36 |@ COIN 1
és as = | ¥ a FI H a Kia
| o— | ° | ° | i |
| Li | Lo | Laat | ei 8 |
| ON/OFF SH | SAFETY SH SAFETY SH | Fis | |
| cToP> | (DOOR? | -+ oO |
z Fi € : J ry z Fe $-TO CONTROL PANEL
H soup ap tL]
pees—aaog7-108B
VOLTAGE SELECTOR 6POS N-N-L
LINE CORD
NOTES?
W_STONE 3720786 BALLY SENTEy INC.
sac 1A
Nos1-eec47-Age3
SHEET 1 REV A or? | fy OLS Se Ee #-TO CONTROL PANEL
pe re eee rie PSPS. B
[ome rar rears 2°
re)
REY. A
MASTER CABLE WIRE HAS CONNECTED TO NOW
+50, RED GREEN-WHITE (G-W> P27, PIN K P19, PIO ve [ose 74 ta +5V RED GREEN-RED (G-R) P?r PIN L PI9y Pil ts ———— AC SENSE GRY FROM ISOLATION TRANSr pee Sense ey Iso! INSFORMER POWER SUPPLY = SENSE WE OF POWER CHASSIS Assy Be06-88209-100B
TO P19 PIN 18
«SEE NOTE 3) ‘SPEAKER CABLE auHT ev assy
OBLK 115¥ ‘GND 4 LOOSE PINNED WIRES
14(SEE NOTE 4> “T@-COIN DOOR LIGHTS {@ COIN METER l@COIN DOOR LIGHTS <6ND) ie SH RETURN OUTS! COIN METER RETURN shee !@- COIN SH 1 SHS61@ COIN SH 2 POWER CHASSIS ASSY | AEe3-00003-9060 - MONITOR
c—" SPEAKER PS "30P08 LEAF
L) DISPLAY LANPS ASSY
TO J16 PIN S AND
Jee PIK S BLK _& SHIELD
BLK S, ON/OFF su t
TO COHTROL PANEL TO 6 POS PCB CONN NOTE 3 ON MONITOR
aupio out ca i
SENTE MAIN CPU BOARD
ean
row AUDIO BD. r 1 BOG6-B8882-1995) , 1 PONG L__TEST su} TEST SW BRKT $-TO CONTROL PANEL
USED ON POWER CHASSIS ASSY VOLTAGE SELECTOR 6POS M-N-L Notes
1@-MASTER CABLE ASSY. CONSISTS OF ALL HIRING IN THIS DIAGRAM EXCEPT FOR HIRING GROUPS IDENTIFIED OTHERWISE
26-CONNECTORS MARKED “P" OF CABLE ASSY’S FASTEN TO CONNECTORS HARKED “J"ON THE PCB’S AND THE POWER CHASSIS ASSY
NOTES® 3@- JACK CONNECTORS MARKED "J" OF CABLE assy’s
BALLY SENTEs INC. we - : I 4 cAPonussa @e8 vacr SELECTION FASTEN TO JACK CONNECTORS MARKED "J" OF GAME ASSY’S. . t $10 an heels SACHA <BLUE> 4@-PLEASE REFER TO SHEET 2 OF 2 FOR COIN DOOR CABLING MODIFICATIONS
IN SAC-HAN KIT INSTRUCTION MANUAL J14 IS A9 PINCOR A 6 PIND JACK CONNECTOR THAT LOOSE WIRES MUST BE PINNED INTO. LINE coRD 7 _22P0S. YELLOW)
MoS1-00£23-Ao05
SHEET 1 OF 1 [REV A
REV. D
MASTER CABLE WIRE WAS CONNECTED TO NOW Fa fa
GREEN-HHITECG-H> Pz» PIN K P19, PIB.
GREEN-REDCG-R> Pp?) PIN L Pid, PAL ORN +5¥ ET WHT 15¥ WHT 154 [nen iev POWER SUPPLY Sic R-Y_ 124 CT BeGS-88809-180B an
GND GND GHD < Fy Ey Ey fal
- ote] 5/5]
ino ee~n [ fad fad Ed DF Rix| | R| | PG 38P08 LEAF
auHT ev TO P19 PIN 18
aBLK _115y
zie 120} COIN METER {COIN DOOR LieHTS FLUORESCENT LIGHT ofp UNRES +1ev GND }@ GROUND Pasa 1 GND 14-COIN BOOR LIGHTS ‘SPEAKERS igo © of ures +12 JOUTE!® COIN METER hea io
TO J16-5 AND J20-5 POWER CHASSIS ASSY AE19-90009-a000 NONITOR
ar) wl Oe an
m4 my
To Zot ° o bi Lt ON/OFF SH 6 SAFETY SH SAFETY SH «TOP> poor? * BLK_& SHIELD
o t SHEL Ie p—SRY-6 a te oale GRY-6. a Aeu i fe Lit FTO CONTROL PAKEL
auDIO our
SR to pig PIN 11
SOUND BD pe96-99002-1005
TO CONTROL PANEL
prs VOLTAGE SELECTOR 6POS M-H-L
LINE CORD u
?
F P
"
v J Y P?_22P0s H H i H H H i H H H H H i H H H H H H H H H H i H i H H H Hl Hl
H H {
i H i i i i H i H i H
i i i
Hi i i i i i
fe 220 VAC SELECTION TO CONTROL PANEL saci 2 1) <mue> E19-B003 a) CT L_ eweer i oF 1 [Rev pO} Boece Es
SILKSCREEN CROSS REFERENCE LIST
DESCRIPTION
UCN 4821 1/4W 5% CARBO 74HC14 LM324 TAHC74 20K 1/4W 1%
80.6K 1/4W 1%
39.2K 1/4W 1%
1K 1/4W 5%
10 POS. SIP 470 OHM -1UF 50V 2.2UF TANT. 10V 8 PIN KK156 W/LOCKING TAB P.C.B. FLOOR PLAY INTERFACE P.C. U006-08029-010B M051-00E38-B8012
oTy.
U4, U5, U6 Dee w < EX)
R26 ,R28,R16, R18 R6,RB 6 R31,R29,R21,R19 R11,R9 9 R24,R27,R30,R14 R17,R20,R4,R7,R10 is R23,R25,R32,R13 R15 ,R22,R3,R5,R12 R1,R2 RPL c2 - c18 Ct Pl PRUE
REV. A - 3/27/86 J.S. DESIGNATION NO. PART NOS.
0066-352XX-XXLX U210-00018-0100 U260-00054-0100 U210-00016-0100 U450-020N02-0100
U450-08062-0100
U450-03922-0100
U400-01001-0100
U460-00012-0100 U300-00009-0100 U310-00013-0100 U550-00065-0100 U007-08029-0108
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
“ via ss bh) 0d 04 O20
(Je cia ure RET vec Gras, a
ces L WSC cas UUW ten 20 flaP]b.5 cee
A! UN-PROG CARTRIDGE 128K W/SECURE CHIP A082-91834-A000 (SENTE BOARD NO. 006-8027-01-0B)
CROSS REFERENCE LIST
DESCRIPTION
PCR 74LS139 74L8245 RAM NOV ST 1002 SECURITY CHIP CAP CER. «1M 50V 20% CAP TANT. 2.2MF 10V 20% SOCKET 28 PIN SOCKET 20 PIN SOCKET 40 PIN CONNECTOR AMP 2-102584-0 OTY.
aa eNnee ee Nw REFERENCE NO. PART _NOS.
U5R U5C usc U6R C1-C23 €24,C025 UTA-UBA,UTC= u7c U6R Pt A080~-91834-A000 U200-00049-0100 U200-00056-0100 U230-00007-0100 U260-00050-010A U300-00009-0100 U310-00013-0100 u4ac 110€-00001-0010 U510-00017-0100 110£-00001-0011 U550-00064-0100
REV: Revisions due to type errors on 1/17/86. ext 2-9 46 M051-00114-A144
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
FLOOR-CONTROL LAMP BOARD ASSEMRLY PART NO. U006-08N28-010A M051-00£38-A010
CROSS REFERENCE LIST
DESCRIPTION QTY. DESIGNATION NO. PART WOS.
| FLOOR-CONTROL LAMP P.C. BD. | 1 | B007-N8028-010A | |
| CONN KK100 PCM MO2A SQ. TIP | 1 | PL | 1550-00086-0100 |
| 120 OHM 1/4W 5% CARBON | 1 | RL | 100E-90005-0035 |
| L.E.D.: RED MV5760 | 4 | LED 1 | 119E-00001-0007 |
00" Z2Pey
ro]
412 VNREG
Rerwaa 4 mnVT160
ot Wud 5%
RELEASED BY: S.F__ 2-11-86 MO5 1-00E38-A011
1209 Anwiiwood Ave. Sunnyvale,
DRAWING NO. C0B- Bo02B- a: