Pole Position TM-218 3rd Printing
Pole Position (World) (Namco, 1982) · Technical Manual · 88 pages · 56 sections · original scan
Complete with Schematics an d Illustrated Parts Lists
and Service Manual
Operation, Maintenance,
\f reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.
WEST and CENTRAL U.S.A. Parts and Service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O, Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) From California, Alaska, or Hawaii Ss (408) 745-2900 Service from anywhere in the area shown in white @ oltre (800) 538-1611
EAST U.S.A. Service only
Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ‘ae From New Jersey (201) 469-5993 From anywhere else in this area toll-free (800) 526-3849
EUROPE
Parts and Service
Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND @ 06252155
PHVF
Operation, Maintenance, and Service Manual
Complete with Schematics
and Illustrated Parts Lists
*Pole Position is engineered and designed by Namco Ltd. Manufactured under license by Atari, Inc.
Pole Position
© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to ‘one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035
Lithographed in the U.S.A. 1M
Notice Regarding Non-ATARI Parts
Use of non-ATARI parts or modifications of your ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:
@ substitute non-ATARI paris in the game @ modify or alter any circuits in the game by using kits or parts not supplied by Atari.
INTERFERE
to licensed communications services is not permitted by the Federal Communications Commission (FCC). If you suspect interference from an ATARI® game at your location, check the following: @ all green ground wires in the game are properly connected as shown in the the game wiring diagram @ the power cord is properly plugged into a grounded 3-wire outlet @ the game PCB is properly installed within the Electromagnetic Intetference (EMI) cage @ the EMI Shield PCB is properly installed and in series with the game PCB harness. Refer to Figure 3-15 to make sure that the game PCB and the Shield PCB are correctly installed. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover for service in your area.
Pole Position
Table of Contents
Set-Up Procedures A. New Features ... 2.6... etee 1-4 B. Inspectingthe Game .. 1-4 C. Leveling the Sit-Down Cabinet. . 15 D. Space and Power Requirements 1-5
- Installation Requirements. . 15
- Selecting the Voltage Piug . 15 E. Locating the Switches ... 1-6
- Power On/Off Switch 16
- Utility Panel Switches 1-7
- Option Switches . . 1-7 4, Memory Back-Up Jumper! 17 F. Setting the Option Switches . 1-7 G. Performing the Initial Self-Test 1-10 H. Game Play.......... 1-12
- Attract Mode 4:12
- Play Mode .... 1-12
- High-Score Mode . » 113
- Hints for Game Play. .......0. 0000.0 cece eee eee seen 413
Self-Test Procedure A. Comments on Troubleshooting . . 22 B. Performing the Self-Test ...... 0.0.0. c ccc cece eee tee eee 2-2
Maintenance, Repair, and Parts A. Cabinet-Mounted Assemblies ........... 00. c cee cece cece eee 3-2 B. Player Controls .........-...2...000005 3-7 C. Fluorescent Tube and Speaker Replacement » 316 D. Video Display. ....................00055 . 3-20 E. Utility Panel . 3-22 F. CoinDoors ... - 324 G. Printed-Circuit Boards . . 330 H. Power Supply Assembly. 2.0.2.0... 0.0 cece ence eee eens 3-51
Glossary of Terms | «20.00.00. ccc ee eee eee GL
Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4
Figure 1-5 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4
Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4
Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8
Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12
Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16
Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20 Figure 3-21
Table 1-1 Table 1-2 Table 1-3 Table 1-4
Table 2-1 Table 2-2 Table 2-3 Pole Position
List of Illustrations
Game Overview, Upright Cabinet ...................00008- +2 Game Overview, Sit-Down Cabinet 1-3 Leveling the Sit-Down Cabinet . . 156 Location of Game Switches. ............ 0... cece e cece 1-6 Self-Test Display... 0.00.0 e eee 4-11 Self-Test Screen 1: Upright Test Passes . 23 Self-Test Screen 1: Sit-Down Test Passes 2:3 Seif-Test Screen 1: Test Fails . - 23 Self-Test Screen 2... 2.0.6 cece eee teen eee 2-4
IHustrated Parts Lists
Cabinet-Mounted Assemblies, Upright Cabinet .............. 3-2 Cabinet-Mounted Assemblies, Sit-Down Cabinet 3-4 Control Panel ...........- 02-2. e eee e eee . 37 Control Panel Assembly ............ 00. cece eee eee eens 3-8 Steering-Whee! Control Assembly ...............000 00 e ee 3-10 Gear-Shifter Control Assembly. . 312 Foot-Pedal Control Assembly . 314 Fluorescent Tube and Speaker Board Removal, Upright ‘Cabinet 3-16
Fluorescent Tube and Speaker Board Assembly Upright Cabinet 3-17 Sit-Down Cabinet Speaker Removal ............0-...0.00005 3-18 Video Display ..............- 3-21 Utility Panel Assembly 3-22
Vertically Mounted Coin Door ...............005 . 3-24 American-Made Coin Door.... . 3-27 Removing the Printed-Circuit Boards .............. . 330 Central Processing Unit Printed-Circuit Board Assembly ...... 3-32
Pole Position Video Printed-Circuit Board Assembly.......... 3-40 Regulator/Audio I PCB Assembly, U.S.-Built Cabinet . - 3-45 Regulator/Audio Ii PCB Assembly, Ireland-Built Cabinet . . 346 EMI Shield PCB Assembly . 349 Power Supply Assembly ............ 20.00. c eee e eee eee eee 3-51
Switch Settings for Game and Price Options ..............-. 1-8 Switch Settings for Game and Play Options . . 149 Seif-Test Procedure ............. «. 4:10 Qualifying Lap Information wee fae coed me ewe 1:13
Locating Failed Components on the Video PCB ............. 2-2 Locating Failed Components on the CPU PCB . 1. 2:2 Locating the Failed RAM... 2.6.0... cece eee 2-4
Pole Position
vi
NOTICE
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause i terference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.
Set-Up Procedures
How to Use this Manual
This manual, written for game operators and service technicians, describes the Pole Position game. The manual contains information about the Upright and Sit-Down Pole Position cabinets. Whenever information is unique to the Upright
cabinet, this symbol appears: i
Whenever information is unique to the Sit-Down
cabinet, this symbol appears: 3)
Wherever information is unique to /reland-Built games, this symbol appears: * Chapter 1 describes new features, game setup, settings of option switches, self-test procedures, and game play. Chapter 2 contains self-test procedures. Chapter 3 details maintenance, repair, and parts information. A glossary of terms is in the back of this manual for your convenience. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the Upright game cabinet; Figures 1-2 and 3-2 illustrate the Sit-Down game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.
VA |e fl
Set-Up Procedures
ATTRACTION PANEL, FLUORESCENT TUBE AND SPEAKER See Figure 3-8 or 3-9 Pole Position
- GAME IDENTIFICATION LABEL (Serial number appears here on Ireland-Built games)
x VIDEO DISPLAY. See Figure 3-11 a DASHBOARD STEERING-WHEEL ‘See Figure 3-1 CONTROL ASSY. See Figure 3-5 EMi CAGE See Figure 3-15 ‘ACCESS PANEL
- GAME PCBs See Figures 3-15, & $20 3.16, & 3:17
GEAR-SHIFTER CONTROL ASSY. See Figure 3-6 UTILITY PANEL + REGULATOR? See Figure 3-12 CAPACITOR AUDIO Ii PCBs See Figure 3:21 See Figures 3-15, (> 318, & 3-19 CONTROL PANEL See Figures 93 & 3-4
SPEAKER See Figure 3-9
POWER ON/OFF SWITCH COIN DOOR * See Figures 3-13 & 3-14
FOOT-PEDAL ASSY, “55 See Figure 3-7
x Items with a serial number label on U.S.-Built cabinets POWER SUPPLY See Figure 3-21
SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a |icensed electrician to install a grounded outiet. You may receive an electrical shock if the game is not properly grounded!
Figure 1-1 Game Overview
Upright Cabinet
1-2
Pole Position Set-Up Procedures
+ GAME IDENTIFICATION LABEL (Serial number appears on exterior of rear access panel of {reland-built games)
- GAME PCBs UTILITY PANEL ASSY. y>) See Figures 3-15, 3-16, & 317 See Figure 3-12 SPEAKER (oe EMI CAGE sear 0 See Figures 3-15 & 320 e Figure [> ATTRACTION PANEL : / See Figure 32 ta ACCESS PANEL || Wd OS. a
- REGULATOR! AUDIO II PCBs See Figures 3-15, 3-18, & 3-19
POWER ON/OFF SWITCH
- POWER SUPPLY CAPACITOR See Figure 3-21 See Figure 3-21
- VIDEO DISPLAY See Figure 3-11
STEERING-WHEEL CONTROL ASSY. See Figure 3-5
GEAR SHIFTER CONTROL ASSY. See Figure 3-6
CONTROL PANEL See Figures 3-3 & 3-4
SHOCK HAZARD See Figure 37 “ty
This game should only be connected to a grounded 3-wire outlet. \f you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock ii the game is not properly grounded! x Items with a serial number label on U.S.-Built cabinets
Figure 1-2 Game Overview Sit-Down Cabinet
1-3
Set-Up Procedures
A. New Features
The Pole Position game has many new features. Even if you are familiar with ATARI® games, you should note these important differences: Electromagnetic Interference (EMI) Cage in U.S-Built Cabinets Only. Games built after December 1, 1982, will have the CPU and Video printed-circuit boards (PCBs) mounted inside this cage. The EMI! cage reduces interference from the game to television and radio receivers. See Figure 3-15 for details. American-Made Coin Door. Your game may be equipped with a new coin door. This door is very similar to the vertically mounted coin door, but does not have lockout coils. When ordering Parts for your coin door, please check coin door illustrations in Figures 3-13 and 3-14 carefully to make sure you are ordering the correct part number. Steering-Wheel Control. This steering wheel is designed to provide a more realistic response from the race car on the display. Foot-Pedal Control (Accelerator and/or Brake). These pedals have been redesigned to accommodate a snap-action switch for the brake anda potentiometer, turned by a spring and cable, for the accelerator. Metal Attraction Panel on Sit-Down Game Cabinet. The metal attraction panel mounted on top of the cabinet entices players with its Formula-1 racing graphics. Quadraphonic Sound in Sit-Down Cabinet. Four 4ohm, 6-ounce, high-fidelity speakers (two under the control panel; two behind the seat) surround the player with the exciting and realistic sounds of Gran Prix racing. New features and other major parts of the game are shown in Figures 1-1 and 1-2. Throughout this manual, wherever a new feature is mentioned, you will See this symbol:
1-4 Pole Position
B. Inspecting the Game
Please inspect your game carefully to ensure that it was delivered to you in good condition.
Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits are firmly plugged into their sockets on the printed-circuit boards (PCBs). c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panei opening. d. Note the game serial number printed on a label on the back of the cabinet. Verify that the same serial number is also on the Pole Position game PCBs, Regulator/Audio II PCBs, power supply, and video display. See Figures 1-1 and 1-2 for locations of the serialnumbered components. Please mention the serial number whenever you call your distributor for service. e. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure they are mounted securely.
To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!
Pole Position
- For the Sit-Down cabinet, remove the metal attraction panel from the protective wrapping. Remove the three button-head screws and retainer on the front window. Place the attraction panel over the mounting holes. Reinstall the retainer and screws.
C. Leveling the Sit-
C. Leveling the Sit Down Cabinet
The Sit-Down cabinet rolls easily from location to location on 4-inch casters. To level the cabinet, lift the game up on one side. Place a block of wood, a book, or another object (that is at least 2-inches thick) under the raised cabinet. Partially unscrew the adjustable glides (see Figure 1-3) until they extend below the caster. Lower the game and lift it up on the other side; partially unscrew the adjustable glides. Lower the game. To prevent players from moving the game around, be sure to adjust all four glides.
CASTER \- ADJUSTABLE GLIDE
Figure 1-3 Leveling the Sit-Down Cabinet Set-Up Procedures
D. Space and Power Requirements
- Installation Requirements
Power 250 W Temperature 0° to + 38°C (+ 32° to + 100°F) Humidity Not over 95% relative Upright Cabinet 62 x 90 cm (25% x 35%, in.) 186 cm (72% in.) Sit-Down Cabinet 165 x 64 cm (65 x 25% in.) 194 cm (76 in.) Space Required Game Height
Space Required Game Height
- Selecting the Voltage Plug
This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!
The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voitage. Next, check the wire color on the voltageselecion plug that is plugged into the game’s power supply. Make sure the voltage-selection plug is correct for the voltage of your location (see Figure 3-21). Now, plug the game into a grounded 3-wire outlet.
Set-Up Procedures
E. Locating the Switches
Do not depress the accelerator or brake Pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls. Pole Position
- Power On/Off Switch
The power on/off switch is located on the back of the Upright cabinet on the lower left side. On the Sit- Down cabinet the power on/off switch is located on the lower left side of the cabinet (see Figure 1-4).
OPTION SWITCHES SWITCH AT 9JA (Game and price) SWITCH AT 9L (Game and play}
Information.
JUMPER AT 6B (Memory back-up) See CO-218-01 for NAMCO PCB UTILITY PANEL ASSY. See Figure 3-12
POWER ON/OFF ‘SWITCH
Figure 1-4 Location of Game Switches
Pole Position
- Utility Panel Switches The volume control(s), self-test switch, coin counters), and auxiliary coin switch are located on the utility panel in both the Upright and Sit-Down cabinets (see Figure 3-12). The utility panel is located inside the upper coin door. The volume control(s) adjust the level of sound produced by the game. The Sit-Down cabinet has four volume controls: one for each speaker. The Upright cabinet has two volume controls: one for each speaker. The self-test switch is used to enter and exit the Self-Test Mode. The coin counter(s) record the number of coins entered into the game. The auxiliary coin switch is used to credit the game without activating the coin counter(s).
- Option Switches Option switches are located on the game CPU PCB (see Figure 1-4). Refer to supplement CO-218-01 for switch locations if your game has NAMCO PCBs.
a. Game and price options are at CPU PCB loca: tion QUA. b. Game and play options are at CPU PCB location 9L.
- Memory Back-Up Jumper The memory back-up jumper is at CPU PCB location 6B. Position this jumper to the on setting. The memory back-up jumper is positioned on the off setting when shipped from the factory to prevent leakage and to provide longer life for the battery at location 6A on the CPU PCB. The jumper must be Positioned to the on setting so that the battery can provide power to the CMOS memory. This memory Stores the high-score table and operator statistics. Set-Up Procedures
The jumper does not affect game play. We recommend you position this jumper to the off setting when you expect extended downtime.
F. Setting the Option Switches
Settings of the game option switches are explained in Tables 1-1 and 1-2. Options preset at the factory are shown by the < symbols. However, you may change the settings according to your individual needs. To verify option-switch settings, first set the power on/off switch to the off position and then to the on position. Next, set the self-test switch to the on position. Compare the information on the screen to the option switch settings listed in the tables in this section. Then set the self-test switch to the off position. Table 1-1 describes the switch settings for options relating to game price, coin mechanism multipliers, number of laps per game, and number of seconds per lap. These switches are on the game CPU PCB at location QUA. The multipliers (QJA switches 1-5) determine the value of the coin mechanisms to the game’s logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. The mechanism either accepts or rejects the coin. The coin door has two coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1.
Set-Up Procedures
| Coin | Option | Interconnect | Assembly |
J55A-P55A permits a coin placed in either coin mechanism to register in the same coin counter. The cable connector is located between the coin door harness and the main harness (see the Coin Op-
| tion | Interconnect | Wiring | Diagram | in | ||
| SP-218). | When | it | is | used, | left | coin |
mechanism option switches at 9JA apply to both coin mechanisms. If you want different options for the left and right coin mechanisms, remove Coin
| Option | Interconnect | Assembly | J55A- |
PSSA and connect J55 directly to P55. If you have NAMCO game PCBs, refer to CO-218-01 for the location of the option switches. Pole Position
Table 1-1 Switch Settings for Game and Price Options
Settings of 8-Toggle Switch on Pole Position CPU PCB (at 9/A)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 |
Option
On Off
Off Off
Off On
On Off On On
On Off On On
On Off On Off On On On On 4racing laps * 3 racing laps <4
90 seconds per lap < 100 seconds per lap 110 seconds per lap 120 seconds per lap *
Right Coin Mechanism 1 coin for 1 credit < 2 coins for 1 credit * 3 coins for 2 credits 4 coins for 3 credits
Left Coin Mechanism 1 coin for 1 credit < 1 coin for 2 credits 1 coin for 3 credits
2 coins for 1 credit * 3 coins for 1 credit 3 coins for 2 credits 4 coins for 3 credits Free Play
4Manufacturer's recommended settings for Upright cabinet
- Manufacturer's recommended settings for Sit-Down cabinet
1-8
Pole Position Set-Up Procedures.
Table 1-2 Switch Settings for Game and Play Options
Refer to CO-218-01 for switch locations if your game is equipped with NAMCO PCBs.
Settings of 8-Toggle Switch on Pole Position CPU PCB (at 9L) 8 7 6 5 4 3 2 1 Option
Off Attract Mode sound off On Attract Mode sound on Off Kilometers per hour On Miles per hour <
#Manufacturer’s recommended settings
Set-Up Procedures
G. Performing the Initial Self-Test
This game will test itself and provide data to show that the game's circuitry and controls are operating properly. The data is provided on the video display and speakers. No additional equipment is necessary. Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you switch to self-test.
Refer to Figure 1-4 for the location of the option switches and Figure 3-12 for the location of the selftest switch. Set the self-test switch to the on position to see the Self-Test Display in the Self-Test Mode (see Figure 1-5). To exit the Self-Test Mode, set the self-test switch to the off position. Pole Position
The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure. \f a part of the test described in Table 1-3 fails, refer to Chapter 2. We suggest you perform the self-test procedure when you first set up the game, when you collect money from the game, when you change game options, or when you suspect game failure.
Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.
Table 1-3 Self-Test Procedure
Instruction Test Passes
- Without touching the pedal(s), set the self-test switch to the on position. All credits will be cancelled.
- Press down on the accelerator pedal,
3, Press down on the brake pedal of the Sit-Down cabinet.
- Turn the steering wheel clockwise, then counterclockwise.
- Shift the gear shifter.
- Shift the gear shift, press the auxiliary coin switch, and activate the coin switches.
- Press the auxiliary coin switch.
- To end the test, switch the self-test switch to off. Random symbols are displayed on the screen for about five seconds. The self-test display appears. RAMs and ROMs are tested. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Self-Test Procedure.
The numbers to the right of ACCEL increase from 00 to somewhere between 90 and AQ as you press down on the pedal. If the test fails refer to Chapter 2.
The numbers to the right of BRAKE switch from 00 to FF. For the Upright cabinet, the numbers to the right of BRAKE should always read 00. If the test fails, refer to Chapter 2. Rotating the wheel clockwise causes the numbers to the right of STEER- ING to increase. Rotating the wheel counterclockwise causes the numbers to decrease. If the test fails refer to Chapter 2.
The words to the right of SHIFT change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, refer to Chapter 2.
The numbers to the right of SOUND increase from 00 to 20, and a new sound is played with each number. Test all 20 sounds. If the test fails, refer to Chapter 2.
Game statistics appear (for a few seconds) at the bottom of the screen. Press the coin switch each time you want to see the statistics. To erase game statistics, simultaneously press down on the accelerator pedal and press the auxiliary coin switch twice. Statistics will be reset at /999/. To reset the high-score table, simultaneously press down on the accelerator pedal and change gear shifter from low to high. The high-score table will be reset and contain fictitious scores.
4-40
Poie Position Set-Up Procedures
ALL RAMS GOOD ALL ROMS GOOD new oO : J BRAKE PEDAL
STEERING Et oo WHEEL ——~STEERING 00 SHIFT LO <————— ceAsHirren SOUNDS ACCELERATOR PEDAL
LEFT COIN : MECHANISM COINL ime RIGHT COIN COIN2. MECHANISM QUALIFYING
LAP TIME TIME : NO. OF LAPS
IN THE RACE GOAL. RACE DIFFICULTY LEVEL_> EX TENDED : QUALIFYING LAP {See Table 1-2) = DIFFICULTY LEVEL PRACTICE : (See Table 1-2)
999. 999, 9
GAME AUTOMATICALLY STARTS* (When correct number of coins aig inserted ‘THE COUNT STARTS AT 999998) AND DECREASES. For example, if you play 10 games, the game sud: tracts 10 trom 939, and the display shows 989 for the number of games played, (Disregard decimal Points)
NO. OF GAMES PLAYED NO. OF POINTS SCORED (x10) NO. OF SECONDS PLAYED NOT APPLICABLE
999. 999, 999,
999. 999, 999,
NO. OF SECONDS THAT GAME 7
HAS BEEN POWERED ON
NO. OF GAMES IN WHICH PLAYER HAS QUALIFIED NO. OF GAMES IN WHICH PLAYER REACHED FINISH LINE
NO. OF GAMES THAT REACHED NO. OF GAMES THAT REACHED THIRD EXTENDED LAP FIRST EXT: “if screen displays MANUAL START, RST aianiatd
suspect the game harness. NO. OF GAMES THAT REACHED Reter to the Schematic Package. SECOND EXTENDED LAP
Figure 1-5 Self-Test Display
Set-Up Procedures
H. Game Play
Pole Position is a one-player game using a color raster-scan video display. The game action takes place at Fuji Speedway in Japan. The country around the speedway consists of green meadows, hills, and snow-capped Mt. Fuji. The player drives a Formula-1 race car on the Fuji Speedway. Player controls consist of a steering wheel, a two-position gear shifter, and accelerator and brake pedals on the Sit-Down cabinet (accelerator only on the Upright cabinet). The object of the game is to finish the qualifying lap as quickly as possible. If the player beats the clock, he qualifies for the Gran Prix at Fuji Speedway; if not, he drives out the remainder of his time along the qualifying course. As a qualifier, the driver is ranked according to his qualifying lap time, from position one (the pole position) to position eight. The player then races against the clock and other cars to finish the four laps (operator-selectable option) of the race as fast as possible and to achieve the highest score possible. The player earns points for passing cars, driving on the track, and finishing the race with time remaining. He is rewarded with an extended-play jap for completing a lap. Pole Position has four modes of operation: Attract, Play, High-Score, and Self-Test. Self-Test is a special mode for checking the game switches and computer functions. You may enter the Self-Test Mode from any other mode. However, all credits will be cancelled. Pole Position
- Attract Mode
The Attract Mode begins when you set the power on/off switch to on or after the Play, High-Score, or Self-Test Modes. The Attract Mode ends when the correct amount of credit for a game is inserted or when the Self-Test Mode begins. When the Attract Mode begins, the game displays a picture with the words POLE POSITION flashing at the top of the screen. A map of Fuji Speedway is displayed in the center of the screen. Within the map are the words FUJ/ SPEEDWAY and 7 LAP 3459M. At the bottom of the screen is the copyright message. Then, the Attract Mode simulates game play. Eight cars are at the starting line. The player's car, located in the eighth position, flashes on the screen. The starting lights flash from red to green and the race starts. The race continues until the player's car crashes into another car and explodes into a red ball of fire. Then, the car reappears on the screen and continues down the track until it hits a sign along the side of the road. Again, the car explodes. During this sequence, the message GAME OVER appears in the center of the screen. Finally, the Attract Mode displays the High-Score Table. The fastest lap time, average game speed, and prize winners appear at the top of the screen. Below this information is a list of the six highest scores. Opposite each score are the initials of the player who achieved that score.
- Play Mode The Play Mode begins when the correct amount of credit for a game is recorded. The game starts with the player’s car behind the starting line and 90 seconds on the clock. (See Section E to select a different clock setting.) The car must finish the qualifying lap within 73 seconds to be in the race. If the player does not qualify, his car continues on the track until 90 seconds are used up.
Pole Position
Table 1-4 Qualifying Lap Information
POSITION QUALIFYING LAP TIME* BONUS POINTS
| 1 | 58" 50 | 4000 |
| 2 | 60" 00 | 2000 |
| 3 | 62” 00 | 1400 |
| 4 | 64" 00 | 1000 |
| 5 | 66” 00 | 800 |
| 6 | 68" 00 | 600 |
| 7 | 70" 00 | 400 |
| 8 | 73” 00 | 200 |
*In seconds and hundredths of a second % The above times apply to manufacturer's recommended settings. Just before the race begins, the player's car (flashing on the screen) is placed at the starting line with seven other cars. The position of the car depends on the qualifying time as shown in Tables 1-4 or 1-5. The starting lights flash from red to green, and the race begins. Racing hazards are other racing cars, sharp turns, and road signs. As the race progresses, more cars appear on the track. If the driver's car hits another car or a road sign, the driver's car is destroyed in an explosion. The driver's car reappears in a few seconds and the race continues. Driving through wet puddles or off the track slows down the driver's car. Racing into the first turn, the driver must let up on the accelerator slightly to make the corner. Road signs flash along the side of the track. Depending on how well the player manipulates the controls, he can either roar through the hairpin turns like a champion or spin out in a flaming crash. He jockeys for position with the other racers, while keeping his eye on the clock at the top of the screen. When his time tuns out, the race is over. The top score achieved by a player appears at the top of the screen. The time alloted for the lap is displayed under the top score. Increasing lap time (in seconds and hundredths of a second) and the speed of the car appears last. Set-Up Procedures
- High-Score Mode The High-Score Mode begins when a player has earned one of the 300 highest scores. The player has one minute to record his initials. A player rotates the steering whee! to locate his initial. He presses a foot pedal to put his initial on the screen. The third time he presses the pedal his initials are transferred into the high-score table.
- Hints for Game Play © Avoid puddles and the sides of the track because these slow you down. © Accelerate and stay ahead of other racers.
- Stick to the inside of the track to make the corners.
- Successful completion of a turn depends on braking skill. © When sliding, steer into the skid.
Pole Position Set-Up Procedures
Table 1-5 Switch Settings for Qualifying Lap Times
| aL | Self-Test | Level | |
| Option | Practice | of | Beat This Many Seconds |
| ‘Switches | Rank | Difficulty | to Qualify tor Position: |
1 2 3 1 2 3 4 5 6 7 8
| On Off On | F | Easy | 66 68 70 73 75 7 80 82 |
| Off Off On | E | 65¥e 67¥2 70 72¥2 74v2 v2 79 81 | |
| On On On | H | 59ve 61 63 66 8 70 72 75 | |
| On On Off | D | 9 6 63 65 67 69 ral 74 | |
| Otf On Off | ca | S8ve 60 62 64 66 68 70 73 | |
| On Off Off | B | 58 60 62 64 66 68 70 72 | |
| Off Off Off | A | Stve 59 61 63 6 67 69 71 | |
| Off On On | G | Hard | 57 59 61 63 65 67 69 ral |
“<Manufacturer's recommended settings
Table 1-6 Switch Settings for Racing Lap Times
| aL | 9A | Self-Test | Top Speed | Number of Seconds |
Option Option T
| ‘Switches | Switch | Extended |
4 5 6 8 Goal Rank MPH KPH Lap 1 Lap 2 Lap3 Lap4 Off Off Off Off 3 A 195 313 75 50 61 — Off Off Off On 4 A 195 313 75 53 58 62 Off On Off Off 3 c 195 313 ri} 4B 60 = Off On Off On 4 c 195 H3 75 51 57 61 On Off Off Off 3 B= 195 313 75 46 59 = On Off Off On 4 e<"* 195 313 75 49 56 60 On On Off Off 3 D 195 313 75 44 58 = On On Off on 4 D 195 313 75 47 55 59 Off Off On Off 3 E 225 360 75 48 60 = Off Off On On 4 E 225 360 75 51 7 61 On Off On Oif 3 € 225 360 75 4B 59 - On Off On On 4 F 225 360 75 49 56 60 Off On On Off 3 G 244 391 75 48 60 ae Off On On On 4 G 244 391 75 St 57 61 Qn On On Off 3 H 244 31 75 46 59 = On On On On 4 H 244 391 75 49 56 60 L 4Manvfacturer's recommended settings *Upright cabinet **Sit-down cabinet
4-14
Self-Test Procedure
The reference designators for components in this chapter refer to games with Atari® PCBs. If you have Namco Q PCBs, please refer to CO-218-01.
The following self-test procedures should be performed by a qualified electronic technician. This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you find the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is working properly.
Chapter
Self-Test Procedure
A. Comments on Troubleshooting
When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you do not find a harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting a PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Tables 2-1 and 2-2 are troubleshooting aids, which can be used to locate faulty components.
Table 2-1 Locating Failed Components Pole Position
Table 2-2 Locating Failed Components on the CPU PCB
Custom AtoD
Symptom Area PROM '€ RAM Converter
Audio Voice 9c 9D Screech/Crash aE Player's Motor 125, 12F All Other Sounds 7L,11D 7K,7J Inputs Brake and/or Accelerator a Steering 9K Option Switches 9K,9M All Other Inputs OM Control for Audio & Inputs 8H,9H Sync 7M High Scores 7E
on the Video PCB
Symptom Area PROM Custom RAM
ic Large Car Pictures 12d, 130 Large Sign Pictures 12K,13K,12L, 13L Small Cars & Signs 12N,13N All Cars & Signs 12H,11N 13H 9F,10F Alphanumerics 7N,8M 8N Raceway 2L,2M,2N,4L 3N Background 6N,5K Raceway & Background SLeL Middle & Sides of Raceway 2B,2C,2D All Video 4D,7E,2F
Red NE
Green 11D Blue 11C
2-2
B. Performing the Self-Test
This game will test itself and provide data to show that the game's circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. Video game repair should only be performed by a qualified electronic technician. To begin the Self-Test Mode, set the self-test switch, which is located on the utility panel, to the on position.
Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.
Self-Test Procedure Pole Position
SELF-TEST SCREEN 1—Test Passes: SELF-TEST SCREEN 1—Test Fails:
Upright Cabinet. If the test passes, the screen If the test fails, the screen may display the picture displays the picture in Figure 2-1, Upright Test in Figure 2-3, Test Fails. Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.
Figure 2-3 Self-Test Screen 1: Test Fails
ROM failure is indicated by the word ROM and a pair of alphanumeric characters displayed at the top Figure 2-1 Self-Test Screen 1: Upright Test Passes of the screen.
Sit-Down Cabinet. If the test passes, the screen displays the picture in Figure 2-2, Sit-Down Test Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.
ACCEL STEERING
EXTENDED J
PRACTICE RANK C AUTO STAR
Figure 2-2 Self-Test Screen 1: Sit-Down Test Passes
Self-Test Procedure
RAM failure is indicated by the word RAM anda Pair of alphanumeric characters displayed at the top of the screen. Table 2-3 lists the failed RAM chip, the printed-circuit board (PCB) the chip is on, and the chip’s location. Replace the failed RAM, and restart the test (set the self-test switch to off, and then to on).
Table 2-3 Locating the Failed RAM
Falled PCB ‘Screen Display RAM Location
Video RAM O 8F
| Video | RAM 1 | 7F |
| Video | RAM 2 | 8H |
| Video | RAM 3 | 7H |
| CPU | RAM6 | 7 |
CPU RAM7 7K
| cPU | RAM 8 | TE |
| Video | RAM 22 | 8 |
| Video | RAM 23 | 7 |
| Video | RAM 26 | 8K |
| Video | RAM 27 | 7K |
| Video | RAM 28 | 3F |
| Video | RAM 29 | 4F |
| Video: | RAM 30 | 3€ |
| Video. | RAM 31 | 4E |
Steering failure is indicated by failure of the numbers to the right of STEERING to properly increase or decrease. As you rotate the wheel clockwise, these numbers should increase; as you rotate the wheel counterclockwise, they should decrease. If the test tails, suspect the Coupler PCB.
Accelerator failure is indicated by failure of the numbers to the right of ACCEL to increase as you press down on the pedal. If no numbers appear, suspect a bad A-D converter on the CPU PCB ora mechanical problem on the foot pedal assembly. Troubleshoot using the information in Chapter 3, Section B, and the game schematics. Pole Position
Brake failure on the Sit-Down cabinet is indicated by failure of the numbers to the right of BRAKE to change as you press down on the brake pedal. On the Upright cabinet, brake failure is indicated by anything other than 00 appearing to the right of BRAKE. If the test fails, suspect a bad switch, improper mechanical adjustment on the foot pedal assembly, or no ground on the brake edge-connector pin in the harness. Gear-shifter failure is indicated by failure of the words to the right of SHIFT to change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, suspect loose connector wires or abad switch. Sound failure is indicated by the absence of any sound when the coin switches or gear shifterare activated. Suspect a loose harness or connector wire, the volume contro! turned off, the custom audio I/O chip, or the Regulator/Audio || board. Troubleshoot using the game schematics. To see self-test screen two, set the self-test switch to off and immediately back to on.
SELF-TEST SCREEN 2:
Awhite crosshatch pattern appears on the screen (see Figure 2-4). Use this pattern for convergence (see the raster-scan video display manual).
Figure 2-4 Self-Test Screen 2
Maintenance, Repair, and Parts
This chapter details maintenance and repair information and provides information you need to order parts for your game. Common hardware (screws, nuts, washers, bolts, etc.) has been deleted from most of the parts lists. However, a parts list for the hardware to mount the printed circuit boards (PCBs) to the cabinet has been included. The printed circuit board (PCB) parts lists are arranged in alphabetical order by component. Each component subsection is sorted by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598-through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.
Chapter
Maintenance, Repair, and Parts Pole Position
A. Cabinet-Mounted Assemblies Manuais, Schematics, & Self-Test Label— See parts list on next page
Fluorescent Tube and Speaker See Figures 3-8 & 3-9 037332-01 a grille) Vs 78-6900404 (Tape)
78-6900402 (Tape) 039371-01 (Shield retainer)
039417-01 403888101 (Display shield) (Lock)
039376-01 (Access panel) Video Display See Figure 3-11
‘A037701-01 78-6900402 (EMI Cage) (Tape) See Figures 3-15 & 3:20 Game PCB Assy. A039420-01 See Figures 3-15, (Dashboard/decalj 3-16, & 3-17 A - Wheel Control Assy. .Gear-Shifter Control Assy. A039459-01
| See Figure 35 | See Figure 3-6 | (Main harn. assy) |
A039499-01
| 178034-024 | Control Panel Assy. | (Main harn, assy) |
(e-Molding) See Figures 3-3 & 3-4
‘opener Regulator/Audio |)
| Utility Panel | Ore | PCB Assy. |
| See Figure 3-12 | 03914401 | See Figures |
nN (Speaker grille) 3-18 & 3-19 Coin Door Assy. ~178088001
| See Figures | A039460.01 | (Caster) |
3-13 & 3-14 (Power harn. assy) 038870-01 Power Supply
| (Coin box enclosure— | See Figure 3:21 | A037453-04 |
not shown) (Power cord) 038091-01 ‘A037454-04
| (Coin box—not shown) | A039353-01 | (Power cord} |
(Cabinet ass
| 178034025 | . | ¥) | ohtaeTon |
(T-Molding) A039353-02 nloff switch assy) (Cabinet assy) 009992-01 78-3201 Foot-Pedal Assy. (On/off switch cover) (Glide) See Figure 3-7
Figure 3-1 Cabinet-Mounted Assemblies U.S.-Built Upright Cabinet A039352-01 B lreland-Built Upright Cabinet A039352:02 B
Pole Position Maintenance, Repair, and Parts
Cabinet-Mounted Assemblies Upright Cabinet Parts List
Assemblies and components in the following parts list are shown in Figure 3-1.
Part No. Description For U.S-Built Upright Cabinet A037453-04 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference Cage (includes guides) A039353-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039459-01 Main Harness Assembly (for U.S. PCB) For Ireland-Built Upright Cabinet A037454-04 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039353-02 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039499-01 Main Harness Assembly (for NAMCO PCB) For U.S.-Built and lreland-Built Cabinets A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039420-01 Dashboard Housing and Decal Assembly A039460-01 Power Harness Assembly A039576-01 Coin Option Interconnect Assembly
The following nine items are technical information supplements to this game: CO-218-01 Pole Position Supplement (for NAMCO game PCB removal) ‘SP-218 Pole Position Schematic Package (for Atari/® game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari® PCBs) or ST-219-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for NAMCO PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218 Pole Position Operation, Maintenance, and Service Manual T™M-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 14-inch Wide x %-Inch Thick (48 inches required; used on top edge of video display shield, and on top edge of contro! panel) 786900404 Vinyl Foam Single-Coated Adhesive Tape, V-Inch Wide x 14-Inch Thick (48 inches required; used on top and bottom of attraction panel) 009992-01 On/Off Switch Cover 037332-01 Ventilation Grille 038091-01 Molded Coin Box (not shown) 038770-01 Metal Coin Box Enclosure (not shown) Acceptable substitute is part no. 038781-01 039144-01 Speaker Grille 039371-01 Video Display Shield Retainer 039376-01 Rear Access Panel (does not inciude lock) 039417-01 Video Display Shield with Graphics 148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (located on front panel) 171034-xxx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001. 178034-024 %-Inch Black Plastic TMolding (located on side panels) 178034-025, 25,,-Inch Black Plastic T-Molding (located on front panel) 178048-001 2-Inch Rigid Caster
Maintenance, Repair, and Parts Pole Position
‘A039465-01 A039101-01 (Main harn. assy.) (Cabinet assy.) A039245-01 A039101-02 (Main harn. assy.) (Cabinet assy.) Game PCB Assy. — See Figures 3-15, 3-16, & 3-17
037990-01 (Vent. Grille)
148001-013 (Speaker) ‘Te034034 039145-01 cine) Agar7o‘01 (Speaker grille) cag See Figures 3-15 & 3:20 oaa14401 (Grille) 038641.01 : 148001.001 (Vent. grille) Qo (Speaker) wen le aT KS ¥
iss 178034-024 Le (T-Molding)
t
Utility Panel { See Figure 3-12
Regulator/Audio II PCB Assy. See Figures 3-18 & 3-19
Power Supply Assy. 035851-01 See Figure 3-21 (Hinge) A039246-01 (Power harn. assy.) A037470-01 A037453-03 (On/off switch assy.) (Power cord) 00999201 A037454-03 (On/oft switch cover) (Power cord)
Figure 3-2 Cabinet-Mounted Assemblies U.S.-Built Sit-Down Cabinet A039100-01 F Ireland-Built Sit-Down Cabinet A039100-02 F
Pole Position Maintenance, Repair, and Paris
Manuals, Schematics, & Self-Test Label— See parts list on next page
Gear-Shifter Control Assy, See Figure 3-6
a) Video Display
Steering: Wheel Control Assy. 5&6 Figure 3:17 See Figure 3-5 (Front window retainer)
ae ‘ 039141-01 78-6900402: — : (Front window)
039148-01 (Display shield/graphics) Control Panel Assy. See Figures 3-3 & 3-4
a
Coin Door Assy. See Figure 3-13 & 3-14 Foot-Pedal Assy. eseroci See Figure 3-7 (Coin box exctosure)
(Caster)
(Glide)
Figure 3-2 Cabinet-Mounted Assemblies, continued U.S.-Built Sit-Down Cabinet A039100-01 F lreland-Built Sit-Down Cabinet A039100-02 F
Maintenance, Repair, and Parts Pole Position
Cabinet-Mounted Assemblies Sit-Down Cabinet Parts List Assemblies and components in the following parts list are shown in Figure 3-2.
Part No. Description For U.S.-Built Cabinet A037453-03 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) A039101-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039465-01 Main Harness Assembly For Iretand-Built Cabinet A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039101-02 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039245-01 Main Harness Assembly (for NAMCO PCBs) For U.S.-Built and Ireland-Built Cabinets A039246-01 Power Harness Assembly A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-07 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 107001-001 Flat Black Paint The following nine items are technical information supplements to this game: CO-218-01 Pole Position Suppiement (for NAMCO game PCB removal) SP-218 Pole Position Schematic Package (for Atari? game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari? PCBs) or ST-219-01 Pole Position Label with Self-Test Procedure and Option Switch Setting (for NAMCO PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218. Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 72-5524 #¥4-20 x 1.50-Inch Hex Head Machine Screw 75-045S Y4-Inch Split-Lock Washer 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x Inch Thick (48 inches required; used on control panel) 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, ¥z-Inch Wide x %;Inch Thick (48 inches required; used in top slot of video display cleat, and on top and bottom of front window) 002728-01 Control-Panel Mounting Bracket 009992-01 On/Off Switch Cover 035851-01 Top Pane! Hinge 037086-01 Front Window Retainer 037990-01 Ventilation Grill (on rear access panel) 038091-01 Molded Coin Box (not shown) 038641-01 Ventilation Grille (on rear access panel) 038870-01 Metal Coin Box Enclosure Acceptable substitute is part no. 038781-01 039141-01 Front Window 039144-01 Speaker Grille (located behind seat) 039145-01 Speaker Grille (located under control panel) 039148-01 Video Display Shield with Graphics 039155-01 Metal Attraction Panel with Graphics 148001-001 6- x 9Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (not shown—located behind seat) 148001-013 6- x 9-Inch Oval, 4-Ohm, 15 W Shielded High-Fidelity Speaker (/ocated under contro! panel) 171034-xxx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001 176015-110 #10 x %Inch Cross-Recessed, Pan-Head Tapping Screw (not shown—for mounting speakers/grilles to seat back) 178034-024 %-Inch Black Plastic T-Molding 178034-034 1-Inch Black Plastic T-Moiding (located on seat back) 178023-001 4-Inch Rigid Caster
Pole Position
B. Player Controls
Opening the Control Panel:
- Unlock and open the rear access panel (see Figure 3-3), Reach through the opening to the top of the control panel.
- Remove the four wing nuts and washers that secure the control panel to the Upright cabinet. Two wing nuts and washers secure the control panel to the Sit- Down cabinet.
- Guide or pull the contro! panel forward to its resting position. The steering wheel and gear shifter are now accessible for maintenance or repair (see Figure 3-4). Make sure the foam tape is in good condition. This tape is on the control panel of the Upright cabinet, and on the display shield for the Sit-Down cabinet.
- Reassemble in reverse order.
Figure 3-3 Control Panel
Maintenance, Repair, and Parts Pole Position
72-JB38145, a “(ciew) Players may receive an electrical shock if this ; control panel is not properly grounded! After ’ servicing any parts on the panel, make sure that the ground wire is firmly attached to the @ metal tab on the inside of the control panel, | ~~ 175002-008 1 (Washer) J
A000608-09 Gear-Shifter Control Assy. See Figure 3-6
(Spacer)
i A039411-01 (Control panel/decal) 039373-01 (Control panel) 039409.04 FA (Washer) (Decai) ‘A039108-01 (Control panel/decal) 039143-01 (Control parel) 039132.01 A (Spacer) 039153-04 (Decal)
(Bezel)
~ 75-5524B (Carriage bolt) N\ ‘A039229-01 Steering-Wheel Contro! Assy. Assembiles A039107-01 and See Figure 3-5 A039412-01 are used with Atari game PCBs; Assemblles A039107-02 and A039412-02 are used with Nameo game PCBs. Figure 3-4 Control Panel Assembly Upright Cabinet A039412:01&-02 A Sit-Down Cabinet A039107-01 &-02 B
Maintenance, Repair, and Parts Pole Position
Control Panel Assembly Parts List
Assemblies and components in the following parts list are shown in Figure 3-4.
Part No. Description
Upright Cabinet A039411-01 Control Panel with Decal (consists of contro! panel 039373-01 and decal 039409-04) 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 4-Inch Wide x ¥%;Inch Thick (96 inches required) Sit-Down Cabinet A039108-01 Control Panel with Decal (consists of contro! pane! 039143-01 and decal 039153-04) 03913201 Control Panel Spacer 75-0358 Ya-Inch Wide Flat Washer 75-5524B #¥%4-20 x 1.50-Inch Black Carriage Bolt
Upright and Sit-Down Cabinets A039229-01 Steering-Wheel Control Assembly (Namco games use part no. A039229-02) A000608-09 Gear-Shifter Control Assembly 72-JB3814S #8-16 x .87-Inch Screw 75-5512B #%-20 x .75-Inch Black Carriage Bolt 75-945S #1%4-20 Hex Locknut 005255-04 Shifter Bezel 03915401 Shifter Spacer 175002-004 #10 Flat Washer
Maintenance, Repair, and Parts Pole Position
039243-01 . 178099-003 (Label) (Steering wheel)
039230-01 (Steering cap)
72-8012 ‘ (Screw) . 039231-01 (Shaft)
178012-002 039234-01 (Retaining ring) (Steering frame) 72-HB3606S — (Hex screw) ————,_
S
A035220-02 SS 178100-001 (Coupler PCB assy.) cc] NS (Flange bearing) 178097-001 <a “mE 175003-002 (Nylon washer) 178012-001 039233-01 i - (Retaining ring) 175002-001 (Washer)
(Encoder shatt) 178101-002 (Gear) 178101-001 (Gear)
175002-002 (Heavy washer) 039232-01 (Spacer) 75-040 (Washer) 035938-01 (Encoding whee!) 72-8008 (Screw) 75-07014 75-044 (Washer) (Split-lock washer) 72-8408 (Screw)
Figure 3-5 Steering-Wheel Control Assembly A039229-01 D ‘See text for lubrication information.
3-10
Pole Position
Before you remove or repair any player control, turn the game off.
Removing the Coupler PCB, Encoding Wheel, and Steering Wheel:
- Open the control panel (see Figure 3-3).
- To remove the steering-wheel control assembly, disconnect the green ground wire from the grounding hardware. Remove the hardware which secures the steering-wheel control assembly to the control panel (see Figure 3-4).
- Unplug the harness connector on the Coupler PCB.
- To remove the Coupler PCB, remove the hardware securing the PCB to the steering frame.
- To remove the encoding-wheel assembly, hold the shaft of the encoding wheel in a fixed position with a Maintenance, Repair, and Parts
wrench. Use an Allen wrench to remove the cap screw, encoding wheel, washers, spacer, and bearing. To remove the encoder shaft, pry off the retaining ring.
- To remove the steering wheel, hold the steering wheel shaft in a fixed position. Remove the cap screw, washers, and gear. Pry off the retaining ring and remove the heavy washer. 7, Reassemble in reverse order.
Lubricating the Steering-Wheel Control: The two gears and the encoder shaft of the steeringwheel control assembly (see Figure 3-5) should be lubricated every six months. The bronze bearings of the steering shaft should be lubricated as needed. To lubricate these subassemblies, first open the control ‘panel (see Figure 3-3). Apply a light film of Nyogel 779 to the two gears, encoder shaft, and both sides of both nylon washers. If necessary, apply a light-duty oil, such as 3-in-One oil, to the bronze bearings.
Steering-Wheel Control Assembly Parts List
Assemblies and components listed in the following parts list are shown in Figure 3-5.
Part No. Description A035220-02 Coupler Printed-Circuit Board Assembly (includes Radial Optical Coupler) 72-8008 #10-32 x 0.50-Inch Steel Socket-Head Cap Screw 72-8012 #10-32 x 0.75-Inch Stee! Socket-Head Cap Screw 72-8408 #4-40 x 0.50-Inch Steel Socket-Head Cap Screw 72-HB3606S #6-32 x 0.38-Inch Zinc-Plated Steel Hex Washer-Head Screw 75-040 #10 Split-Lock Washer 75-044 #4 Split-Lock Washer 7507014 #4 Flat Washer 79-58356 4-Position Connector with Locking Ramp (located on the Coupler PCB Assembly) 030369-01 Radial Optical Coupler (located on the Coupler PCB Assembly) 03522101 100 2, +5%, %W Resistor (located on the Coupler PCB Assembly) 039230-01 Steering Cap 039231-01 Steering Shaft 039232-01 Spacer 039233-01 Encoder Shaft 039234-01 Steering Frame 039243-01 Steering Cap Label 035938-01 Encoding Wheel 107013-001 3-in-One® Oil 175002-001 Flat Washer 175002-002 #10 Heavy Flat Washer 175003-002 Nylon Flat Washer 178012-001 Retaining Ring for 0.75-Inch Shaft 178012-002 Retaining Ring for 0.25-Inch Shaft 178027-001 Nyogel 779 Lubricant 178097-001 Bearing for 0.25-Inch Shaft 178099-003 Steering Wheel 178100-001 Bearing Flange for 0.75-Inch Shaft 178101-001 24 Diametral Pitch x 20° Pressure Angle x 2.500 Pitch Diameter Spur Gear 178101-002 24 Diametral Pitch x 20° Pressure Angle x 0.583 Pitch Diameter Spur Gear
Maintenance, Repair, and Parts Pole Position
(005255-04 OD (Bezel) \
d See text for lubrication information.
000610-02 (Shifter handle)
039705-01 (Spring)
76-11375S (Ball bearing) 000609-02 (Shift housing)
7214128 a (Screw) 65-0214 (Switep} > 03579201 (Shift detent)
15-9445, NN (Hex nut) 035301-01 (Actuator pin)
Figure 3-6 Gear-Shifter Control Assembly A000608-09 Z
3412
Pote Position
Before you remove or repair any player control, turn the game off.
Removing the Gear-Shifter Control Assembly:
1. Open the control panel (see Figure 3-3). Maintenance, Repair, and Parts
- To remove the switch, remove the two screws and locknuts that secure the switch to the housing. Be careful not to lose the small actuator pin that sits above the switch actuator.
- Reassemble in reverse order.
Lubricating the Gear-Shifter Control:
- To remove the gear-shifter control assembly (see Figure 3-4), disconnect the plug-in connectors from To lubricate the i : gear-shifter control assembly, open the the dele Remove the Miedo that secures the control panel (see Figure 3-3) and remove the gear-shifter gear-shifter control assembly to the control panel. control assembly using the procedure above. Apply a light-
- To open the gear-shifter assembly, remove the six duty lubricant (such as Nyogel 779) every six months to the screws that secure the two halves of the housing (see spherical part of the handle and the detent. Figure 3-6).
Gear-Shifter Control Assembly Parts List
Assemblies and components listed in the following parts list are shown in Figure 34.
Part No. Description 000610-02 Gear-Shifter Handle 65-021A Single-Pole Single-Throw Low-Force Miniature Switch . 72-JB3606 #6 x 0.38-Inch Steel Plastite Screw 72-14128, #4-40 x 0.75-Inch Cross-Recessed Pan-Head Steel Machine Screw 76-11375S, ¥-Inch Ball Bearing 75-944S #4-40 Self-Locking Polymer Hex Nut 039705-01 Spring 000609-02 Gear-Shifter Housing (two required) 005255-04 Shifter Bezel 035792-01 Shift Detent 035301-01 Actuator Pin 178027-001 Nyogel 779 Lubricant (not shown)
3-13
Maintenance, Repair, and Parts Pole Position
039240-01 039236-01 (Foot pedai—accelerator)
00059201 (Compression spring)
178012-004. 29242-01 (Retaining ring) ~ (Cable) . AlYFs
039238-01
\ 03970401 4 * i : MO 72-8606 (Extension spring) (cap screw) Cap screw of pulley must be in a this position when pedal is fully open (at rest). 039703-01 (Cable spring) 039239-01 (Base piate) we 72-HB3410S* 19-9026 L (Screw) (Potentiofnetes) 160023-001* (Switch)
*For Sit-Down cabinet (dual foot pedal assembly) **For Upright cabinet (single foot-pedal assembly)
03914201" ae Mounting plate) 75-9418 “ S 039379.01"°* (Hex locknut) (Mounting plate)
, a 75-0408** See text for lubrication information. (Washer)
Figure 3-7 Foot-Pedal Control Assembly
Pole Position Maintenance, Repair, and Parts
- The only maintenance required on this newly de- Removing the Foot-Pedal Control Assembly: signed foot-pedal control is lubrication every four 9 v months (see Figure 3-7). Lubricate the pivot pin and
| 4. | Unlock and open the rear access pane!. Reach through | surrounding area, the springs, cable, and pulley with |
the opening to the top of the toot-pedal control. dry teflon spray. If needed, apply a light-duty lubricant
- Remove the two locknuts located on the top two footlike WD-40 to the potentiometer shaft only. pedal mounting screws. 9. Reassemble in reverse order.
Foot-Pedal Control Assembly Upright A039413-01 D Sit-Down A039109-01 C Parts List
Assemblies and components in the following parts list are shown in Figure 3-7.
Part No. Description Sit Down Cabinet
A039247-01 Dual Foot-Pedal Control Harness Assembly 72-HB3410S #4-40 x .62-Inch Thread-Forming Hex Washer-Head Screw 75-010S #10 Tooth Internal Lock Washer 160023-001 SPDT Snap Switch with Actuator Upright Cabinet A039463-01 Single Foot-Pedal Control Pedal Harness Assembly 75-035S Ya-Inch Flat Washer 75-040S #10 Tooth Internal Lock Washer 75-5520B #1%-20 x 1.25-Inch Black Carriage Bolt (not shown) 75-9158 #%-20 Hex Nut 039379-01 Single Foot-Pedal Control Mounting Plate Upright and Sit-Down Cabinets 19-8026 5 k@ Potentiometer 72-8606 #6-32 x .38-Inch Hex Socket-Head Cap Screw 75-9418 #10-24 Hex Locknut
| 000592-01 | Compression Spring | (for pedal) |
039236-01 Pivot Pin 039238-01 Pulley 039239-01 Foot-Pedal Control Base Plate 039240-01 Foot Pedat 039241-01 Safety Tread 039242-01 Cable 107012001 Dry Teflon Spray Lubricant (not shown) 178012-004 External Retaining Ring for %-Inch Diameter Shaft
| 039703-01 | Extension Spring | (for cable) |
| 039704-01 | Extension Spring | (for pedal) |
3-15
Maintenance, Repair, and Parts.
C. Fluorescent Tube and Speaker Replacement
Upright Cabinet
Removing the Tube and Speaker Board:
1. From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker's 5-pin harness connector (see Figure 3-8). From the front of the game, remove the three buttonhead screws and lock washers that secure the upper attraction-panel retainer to the cabinet. Loosen the screws and washers that secure the lower attractionpanel retainer to the cabinet. Remove the atiraction glass. Remove the tower retainer. Pole Position
Remove the two wood screws that secure the tube and speaker board to the cabinet. Slide this board out of the cabinet. After making necessary repairs or replacements, make sure that the tube and speaker board is pushed all the way back on the tube and speaker panel when you reinstall the board.
Replacing the Fluorescent Tube:
1. Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start. Remove the cardboard locking tab at each end of the tube (see Figure 3-9). Slightly rotate the tube up or down and carefully remove it from the tube holder. Replace it with a new tube. Do not snap in the tube vigorously— you may break it, causing an implosion! Replace the locking tabs.
Replacing the Upper Speaker:
4. Disconnect the two plug-in connectors on the speaker.
Replacing the Lower Speaker: From the back of the game, unlock and open the rear access panel. Refer to upper speaker removal procedure in Figure 3-9.
78-6900402 (Tape) ogeqte01— (Attraction glass/ graphics)
78-6900402 (Tape)
148001-001 039144-01 (Speaker) (Speaker grille) 4 Ses
00305301 (Retainer)
Figure 3-8 Fluorescent Tube and Speaker Board Removal
3-16
Pole Position Maintenance, Repair, and Parts
148001-013 3 70-304 99-11006 (Speaker) (Tube) (Tab) Co 179036001! _ (Tube holder) ! 176015-410__, @ A037457-01 i (Screw) (Harness)
142028-001 (Transformer) 142028-002 (Transformer)
(Starter) 99-11009 037469-01 (Socket) (Bracket)
Figure 3-9 Fluorescent Tube and Speaker Board Assembly U.S.-Built Upright Cabinet A039415-01 A Ireland-Built Upright Cabinet A039415-02 A Parts List
Part No. Description For U.S-Built Upright Cabinet 142028-001 60 Hz, 118 V, Ballast Transformer (used on A037458-01 assembly) For freland-Built Upright Cabinet 142028-002 50 Hz, 118 V, Ballast Transformer (used on A037458-02 assembly) For U.S- and freland-Built Upright Cabinet A037457-01 Tube and Speaker Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ‘4-Inch Wide x Inch Thick 79-561816P. Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 003053-01 Upper and Lower Attraction Glass Retainer 037469-01 Steel Tube Bracket 039366-01 Tube and Speaker Board 03941801 Attraction Glass with Graphics 148001-013* 6 x 9-Inch Oval, 4-Ohm, 6-Ounce, Shielded High-Fidelity Speaker 176015-110 #10 x 5/8-Inch Pan Screw 179035-001 2-Pin Fluorescent Tube Holder *148001-001 6 x GInch Oval, 4-Ohm, 6-Ounce, High-Fidelity Speaker—mounted to the cabinet near the coin door, behind speaker grille part no. 039144-01
3-17
Maintenance, Repair, and Parts Pole Position
Sit-Down Cabinet Replacing the Seat-Panel Speakers: ASS
Pp g P 4. Remove the six wood screws that secure the seat- Replacing the Front Speakers: back panel to the cabinet (see Figure 3-10).
| 1. | For the right speaker, unlock and open the rear access | 5. | Lean the seat-back panel forward. Disconnect the two |
panel (see Figure 3-10). For the left speaker, open the plug-in connectors on each speaker.
| Contro} panel (see Figure 3-3). | 6. | Remove the seat-back panel from the player area of | |
| 2. | Unplug the two plug-in connectors. | the cabinet. | |
| 3. | Remove the two screws that secure the speaker to the | 7. | Remove the four screws that secure each speaker to |
wood speaker panel. the seat-back panel.
- Reassemble in reverse order.
Figure 3-10 Sit-Down Cabinet Speaker Removal
3-18
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance, Repair, and Parts
D. Video Display
Removing the Video Display From the Upright Cabinet:
1. From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-17). Remove the four sets of hardware that secure the video display to the wood display shelf. Qpen the control panel (see Figure 3-3). Remove the three wing nuts (located on the displayshield support) that secure the dashboard panel to the cabinet. From the front of the cabinet, lift off the dashboard panel. Remove the hardware that secures the dispiay-shield retainer. Lift the display shield up and out of the cabinet. Remove any staples that may secure the bezel to the cabinet. Then, carefully remove the cardboard bezel. Carefully pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.
3-20 Pole Position
Removing the Video Display From the Sit-Down Cabinet:
1. From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-11). Remove the four sets of hardware that secure the video display to the wood display shelf. Open the control panel (see Figure 3-3). Move to the piayer area of the cabinet. Grasp the bottom edge of the video display shield and slide the shield out and down. Make sure the foam tape on the bottom of the shield is in good condition. Remove any staples that may secure the bezej to the cabinet. Then, carefully grasp the bottom edge of the cardboard bezel and remove it from the cabinet. Pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.
Pole Position
039371-01 | (Retainer) Maintenance, Repair, and Parts
039148-01 (Shield) 039149-01 H (Bezel) 03941701 i ere) (Shield) 039407-01 (Bezel)
92.049 (Electrohome display) & or 139003-1004 (Matsushita display)
039363-02 (Shelf) ] 039123-02 & (Shei) Ss ay
Figure 3-11 Video Display Upright and Sit-Down Cabinets Parts List
Part No. Description
For Upright Cabinet 039363-02 Display Shelf 039371-01 Retainer 039407-01 Display Bezel 039417-01 Display Shield 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x Inch Thick
For Sit-Down Cabinet 039123-02 Display Shelf 039148-01 Display Shield 039149-01 Display Bezel 786900804 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %-Inch Thick
92-049 For Upright and Sit-Down Cabinets 19-Inch Electrohome Color Raster-Scan Display Alternate display is part no. 139003-1004— 19-Inch Matsushita Color Raster-Scan Display
3-21
Maintenance, Repair, and Parts Pole Position
E. Utility Panel The utility panel is located inside the upper coin door. This panel includes the volume control(s), self-test switch, auxiliary coin switch, and the coin counter(s) (see Figure 3:12). The auxiliary coin switch is used to credit the game
‘A039254.01 (Dual component 03945701 harness) (Utility panel— US -Built Upright only) . (Ourepema ay ae hamess) tility panel A002485.01 an (Coin counter) A039248-01 (Voi, control harness) 178070-001 (Yol. control knob)
176018-002 (Screw) fs ‘> 75916S 2 eee Hex nu 715997009 Ss 62.041 (Stamped nut) (Auxiliary coin switch)
SWITCH NOT USED
Figure 3-12 Utility Panel Assembly A039391-xx E
3-22
Pole Position Maintenance, Repair, and Parts
Utility Panel Assembly Parts List
Part No. Description For U.S-Built Upright Cabinet 039457-01 Utility Panel (for 2 volume controls) For Ireland-Built Upright Cabinet 039295-01 Utility Panel (for 4 volume controls) For U.S-and Ireland-Built Upright Cabinet A039254-01 Dual Component Harness Assembly For U.S-and Ireland-Built SitDown Cabinet A038004-01 Utility Panel Harness Assembly A039248-01 Volume Control Harness Assembly 039295-01 Utility Panel (far 4 volume controls) For U.S-and Ireland-Built Upright and Sit-Down Cabinets A002465-01 6 V Coin Counter 19-9032 50 &, 12.5 W Volume Control 62-041 SPST Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPOT Self-Test Switch 176018-002 #6-32 x Y2-Inch Thread-Forming Screw 75-916S #6-32 Steel Machine Hex Nut 75-9910W0O #15/32-32 Stamped Nut 178070-001 Volume Control Knob
3-23
Maintenance, Repair, and Parts
FE Coin Doors
170000-001 (Lamp)
179047-001 NS
99-15056 (Screw for Bezel) 99-15026 (Coin Inlet) 99-15025 ® (Coin Inlet) oa
99-15055 (Retaining Screw)
‘.
75-914S Hex Nut) (Hex ND 5 056 (Lock Wash.)
99-15075
99-15029 (Bracket)
99-1504; (Switch) Pole Position
99-15023 (Base Plate)
; ae ttever) Sy y| \
~ 99.15054
(Pivot for Lever)
99-15028 ‘(Coin Return Box)
99-15056
se rew for Bezel)
~<— 99-15060 (Sw. Cover)
721414S (Screw)
Figure 3-13 Vertically Mounted Coin Door 171034-xxx
3-24
Pole Position Maintenance, Repair, and Parts
99-15067. (Lock Assy.) 29450: 15038 A037542-11 (Bezel for Button) (Harness—not snown)
99-15073 (Upper Door) ™ ; s 99-15063 bee . *
(Screw) 99-15001 thru 99-15011 (Return Button}
99-15071 (Clamp)
: 99-15039 lee SS (Bezel tor Cover) '99-15036 (Cover)
038091-01 (Coin Box) 9915066 Screw)
9915074 (Lower Door)
(Doors and Frame) 99-15072 (Door Frame}
171034001 — U.S. 25¢/25¢ Coin Door 171034-006 — U.K. 20 P/50 P Cain Door 171034011 — German 1 M/5 M Coin Door 171034003 — Canadian 25¢/25¢ Coin Door 171034-009 — German 2 Mit M Coin Door 171034015 — French 2 Fi F Coin Door 171034-005 — U.K. 10 P/50 P Coin Door 171034010 — German 2 M/5 M Coin Door
Figure 3-13 Vertically Mounted Coin Door, continued 171034-xxx
3-25
Maintenance, Repair, and Parts Pole Position
Vertically Mounted Coin Door Parts List
Part No. Description A037542-01 Harness Assembly 72-1414S #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75.9148 #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005, Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin inlet 99-15026 Right Half of Coin Intet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054. Pivot for Coin Return Lever 99-15055, Retaining Screw 99-15056 #4-40 x 3,-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw tor Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-5073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly) Acceptable substitute is part number A037491-01 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base
3-26
Pole Position Maintenance, Repair, and Parts
99-10140 (Panel assy.)
75-948S wo (Locknut) ee 99-10116 (Lever)
99.10152 (Right coin inlet)
99-10096 (Fastener)
99-10151 (Left coin inlet)
(Bar retainer) 72.9406S (Screw) ~ 99-10147 (Harness) Z 99-10105 (Bar) 99-10154 a a (Bracket assy.)
99-10042 thru 99-10045 99-10153 (Coin switch assy.) (Coin return box)
65-441C (Coin switch) 99-10150 (Switch cover)
99-1075 thru 99-10078 _— . (Switch wire) 99-10008 ~_ 7514128
(Retainer) (Screw)
Figure 3-14 American-Made Coin Door 171027-001 A
3-27
Maintenance, Repair, and Parts aD Pole Position
99-10148 (Lock)
72-HA1404C (Screw) rs 9910142 = (Button housing)
99-10139 (Co —>+| (Con coon 99-10134 (Cover)
a 99-10118 a (Button) a 99-10115, we (Spring)
—w 9.10141
99-10117 (Coin return door)
2 99-10144 |~—(Channel clip)
72.JA1405B ' , o : a Se (Screw)
9910149 (ervice door)
038091.01 (Coin box)
99-10143 (Frame)
Figure 3-14 American-Made Coin Door, continued 171027-001 A
3-28
Pole Position Maintenance, Repair, and Paris
American-Made Coin Door Parts List Assemblies and components in the following parts list are shown in Figure 3-14.
Part No. Description
171006-035 Metal Coin Mechanism for U.S, $.25 65-4416 Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x ¥-Inch Truss-Head Screw 72-HA1404C_ #4-40 x ¥%4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x ¥%-Inch Pan-Head Screw 75-9945 #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045, Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire (included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly} 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145 Offset Cam (includes 99-10148—Lock) 99-10146 Coin inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly
3-29
Maintenance, Repair, and Parts Pole Position
G. Printed-Circuit Boards A037767-01 (EMI Shield PCB) 039378-03 (Retainer) Shield PCB 176015-110 See Figure 3-20 balled (Screw) (Spacer) .
A039431-01 (End PCB)
»
~ t\6
@ (Screw) 034536-02 ‘A037701-01 (Foam pad) 72A604F (EMI cage) (Screw)
‘A039187-21 178044-242 A039185-21 (Pole Position Video PCB) pi (Pole Position CPU PCB) (Washer) NOTE 178045-442 The FCC requires that the game (Fastener) PCB be housed in the EMI cage with the Shield PCB attached.
‘A036435-01 176015-110 A035435-05 (Screw) (Regulator! 175004-708 Audio |! PCB) (Washer)
*Steps 1, 10, and 11 are not illustrated.
Figure 3-15 Removing the Printed-Circuit Boards
Pole Position
Before you remove or repair any printed-circuit board, turn the game off.
Removing the Printed-Circuit Boards: Removing the Game PCBs irom the EMI Cage 1, Open the rear access panel.
- The game printed-circuit boards (PCBs) are located inside the electromagnetic interference (EMI) cage (see Figure 3-15). The EMI cage is located on the cabinet wall of the Upright game and on the inside of the rear access panel of the Sit-Down game. Unplug the two harness edge-connectors from the EMI Shield PCB.
- Toremove the game PCBs, pull the eight nylon snap-in fasteners on the EMI Shield PCB to the unlocked position. Carefully slide the Shield PCB and attached PCBs straight out of their guides. Be careful not to twist the boards, as this may loosen connections or components. Removing the EMI Shield PCB from the Game PCBs
- Remove the two pan-head screws that connect the EMI Shield PCB to the spacers.
- Push the EMI Shield PCB off the game PCBs by applying pressure with your thumbs to the edge connectors. Maintenance, Repair, and Parts
- Unplug the End PCB that connects the two game PCBs.
- Determine which PCB you need to repair or replace, and remove the two pan-head screws that connect that PCB to the spacers. Replace or repair as required, and reinstall the PCBs. (Make sure the foam vibration damper is placed between the game PCBs.) Removing a Regulator/Audio II PCB:
- To remove a Regulator/Audio || PCB, disconnect the small harness connectors on the board. 9 Remove the hardware that secures the Regulator/Audio |} PCB to the cabinet, and carefully lift the board from the retainer. Do not twist the board, as this may loosen connections or components. Replace or repair as required and reinstall the PCB.
Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. Areversed connector may damage your game and void the warranty.
- Close and lock the rear access panel.
- Important: Perform the self-test.
Printed-Circuit Board Mounting Hardware Parts List
Assemblies and components in the following parts list are shown in Figure 3-15.
Part No. Description
U.S-Built Upright and Sit-Down Cabinets A037701-01 Electromagnetic Interference (EMl) Cage (includes guides) 72-1404F #4-40 x V%4-Inch Cross-Recessed Steel Screw 72-1604 #6-32 x ¥%4-Inch Cross-Recessed Steel Screw 034536-02 Foam Pad 037873-01 Spacer 039378-03 Dual-Slotted Retainer 175004-708 #8 Fiber Washer 175009-221 Plastic Spacer (for EM/ shield PCB) 176015-110 #10 x %Inch Cross-Recessed Pan-Head Screw 178044-242 Grommet 178045-442 Snap-In Fastener lrefand-Built Upright and Sit-Down Cabinets’ 72-6624S #6 x 1 ¥2-Inch Cross-Recessed Pan-Head Tapping Screw 03453602 Foam Pad 039157-02 Dual-Slotted PCB Retainer 175004-708 #8 Fiber Washer 176015-110 #10 x %-Inch Cross-Recessed Pan-Head Screw 178020-750 Nylon Spacer
“Not shown in illustration
3-31
Maintenance, Repair, and Parts Poie Position
ae tk
a -
z = cr x o =z nn m oo w > Figure 3-16 Central Processing Unit (CPU) Printed-Circuit Board Assembly A039185-21 B
3-32
Pole Position Maintenance, Repair, and Parts
Figure 3-16 Central Processing Unit Printed-Circuit Board Assembly Parts List
Components in the following parts list are shown in Figure 3-16.
| Designator | Description | Part No. |
Capacitors
| C2-C5 | 0.01 uF, 100 V Radial-Lead Mylar Capacitor | 21-101103 |
| C6 | 33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor | 128002-330 |
| C7 | 0.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| co | 10 uF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250106 |
| C10 | 0.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C1 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-100476 |
| C12 | 0.1 pF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C13 | 0.01 pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C14, C15 | 0.1 pF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C16-C23 | 0.01 pF, + 80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C24, C25 | 0.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C26 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-100476 |
| C27, C28 | 0.0022 uF, + 10%, 100 V Radial-Lead Plastic Film Capacitor | 121022-222 |
| C29, C30 | 0.022 pF, 100 V Radial-Lead Mylar Capacitor | 21-101223 |
| C31, C32 | 0.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C33, C34 | 0.047 uF, 100 V Radial-Lead Mylar Capacitor | 21-101473 |
| C35 | 0.022 pF, 100 V Radial-Lead Mylar Capacitor | 21-101223 |
| C36 | 0.0047 uF, 100 V Radial-Lead Mylar Capacitor | 21101472 |
| C37 | 0.001 uF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
| C38 | 0.0047 pF, 100 V Radial-Lead Mylar Capacitor | 21-101472 |
| C39, C40 | 0.01 uF, 100 V Radial-Lead Mylar Capacitor | 21-101103 |
| C41 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-100476 |
| C42, C43 | 0.0047 pF, 100 V Radial-Lead Mylar Capacitor | 21-101472 |
| C44, C45, | 0.001 pF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
| C46 | 470 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C47-C56 | 22 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-160226 |
Acceptable substitute is part no. 24-100477
| C57-C84 | 0.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 422002-104 |
| C82 | 0.001 uF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
Diodes
| CR1 | Type-MV5053 Light-Emitting Diode | 38-MV5053 | |
| CR2 | 6.2 V, | +5%, 1 W Type-1N4735A Zener Diode | 131009-001 |
| CR3-CR5 | 100 V, Type-1N914 Switching Diode | 31-1N914 | |
| CR6 | 3.9 V +5% Type-1N748A Zener Diode | 131000-002 | |
| CR7-CR12 | 100 V, Type-1N914 Switching Diode | 31-1N914 |
Integrated Circuits
| 2N | Type-12L6 Programmable-Aray Logic 1 | 137280-001 |
| 3A | Type-28002 16-8it Microprocessor | 137275001 |
| 3c | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 3F, 3H | Custom Integrated Circuit 10 | 137281-001 |
(Continued on next page)
3-33
Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued Pole Position
| Designator | Description | Part No. |
| 3M, 4C. | Type-74LS373 integrated Circuit | 37-74LS373 |
| 4F, 4H | Custom Integrated Circuit 10 | 137281-001 |
| 4M | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 4N | Type-Z8002 16-Bit Microprocessor | 137275-001 |
| 5A | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 5C | Type-12L6 Programmable-Array Logic 1 | 137280-001 |
| 5D | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 5E | Type-74LS244 Integrated Circuit | 37-74LS244 |
| Bu | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 5K | Type-74LS244 Integrated Circuit | 37-74LS244 |
| 5L | Type-74LS368 Integrated Circuit | 137168-001 |
| 5M | Type-74LS158 Integrated Circuit | 137203-001 |
| 5N | Type-74LS74 Integrated Circult | 37-74LS74 |
| 6A | Type-74LS161 Integrated Circuit | 37-74LS161 |
| 6C | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 6D-6F | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 6H | Custom Integrated Circuit 08 | 137 186-001 |
| 6J, 6K | Type-74LS157 Integrated Circuit | 37-74LS157 |
| 6L | Type-74LS109 integrated Circuit | 37-74LS109 |
| 6M | Type-74LS00 Integrated Circuit | 37-74LS00 |
| 6N | Type-74S163 Integrated Circuit | 137274-001 |
| 7c | Type-10L8 Programmable-Array Logic 3 | 137279-001 |
| 7D | Type-Z80A 8-Bit Microprocessor | 137194-001 |
| 7M | Custom Integrated Circuit 07 | 137193-001 |
| 7N | Type-74S04 Integrated Circuit | 37-74S04 |
| 8D | Type-74LS138 Integrated Circuit | 137177-001 |
| 8E | Type-74LS259 Integrated Circuit | 37-74LS259 |
| 8F | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 8H | Custom Integrated Circuit 08 | 137186-001 |
| 8J | Type-ADC0804 Integrated Circuit | 137273-001 |
| 8K | Type-4066 Integrated Circuit | 37-4066 |
| 8L | Type-4584B Integrated Circuit | 37-4584B |
| 8M | Type-74LS04 Integrated Circuit | 37-74LS04 |
| 9E | Custom Integrated Circuit 52 | 137284-001 |
| OFA | Custom Integrated Circuit 54 | 137285-001 |
| 9FB | Type-LM324 Integrated Circuit | 37-LM324 |
| 9H | Custom Integrated Circuit 06 | 437192-001 |
| 9K | Custom Integrated Circuit 53 | 137188-001 |
| 9M | Custom Integrated Circuit 51 | 137187-001 |
| 410A | Type-74LS138 Integrated Circuit | 137177-001 |
| 10C | Type-74LS374 Integrated Circuit | 37-74LS374 |
| 10D | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 10E, 10F | Type-74LS283 Integrated Circuit | 137204-001 |
| 10H, 10J | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 10K, 10L. | Type-4066 Integrated Circuit | 37-4066 |
| WA | Type-74LS174 Integrated Circuit | 37-74LS 174 |
| 11C | Type-7497 Integrated Circuit | 37-7497 |
| HE | Type-74LS273 Integrated Circuit | 37-74LS273 |
3-34 (Continued on next page)
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| q1F | Type-4051 Integrated Circuit | 137277-001 |
| 41H | Type-74LS174 Integrated Circuit | 37-74LS174 |
| Wd | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 11K-11M | Type-4066 integrated Circuit | 37-4066 |
| 124 | Type-74LS174 integrated Circuit | 37-74LS174 |
| 12B | Type-7497 Integrated Circuit | 37-7497 |
| 12Cc | Type-74LS 161 Integrated Circuit | 37-74LS 161 |
| 12D | Type-74LS393 integrated Circuit | 37-74LS393, |
| 12H, 12J, 12M | Type-LM324 Integrated Circuit | 37-LM324 |
Random-Access Memories
| 7E | CMOS Random-Access Memory | 137278-001 |
| 7d, 7K | Random-Access Memory | 137 199-001 |
Read-Only Memories
| co | Electrically Programmable Read-Only Memory* | 136014-106 |
| 3E | Electrically Programmable Read-Only Memory* | 136014-103 |
| 3L | Electrically Programmable Read-Only Memory* | 136014-101 |
| 4E | Electrically Programmable Read-Only Memory* | 136014-104 |
| 4u | Electrically Programmable Read-Only Memory* | 136014-102 |
| 7F | Electrically Programmable Read-Only Memory | 136014-116 |
| 7H | Electrically Programmable Read-Only Memory* | 136014-105 |
| 7L | Programmable Read-Only Memory | 136014-117 |
| 11D | Programmable Read-Only Memory | 136014-118 |
| 12E | Electrically Programmable Read-Only Memory* | 136014-111 |
| 12F | Electrically Programmable Read-Only Memory* | 136014-110 |
Resistors
| Ri | 220 Q2, +5%, %4 W Resistor | 110000-221 |
| R2-R8 | 2.2 kQ, +5%, % W Resistor | 110000-222 |
| RO | 1k2, +5%, v4 W Resistor | 110000-102 |
| R10-R16 | 2.2 kQ, +5%, v4 W Resistor | 410000-222 |
| R17-R20 | 1kQ, +5%, % W Resistor | 110000-102 |
| R21-R26 | 1k2, +5%, % W Resistor | 410000-102 |
| R27-R34 | 2.2 kQ, +5%, 1 W Resistor | 110000-222 |
| R35 | 1kQ, +5%, %4 W Resistor | 110000-102 |
| R36-R38 | 2.2 kQ, +5%, v4 W Resistor | 110000-222 |
| R39-R43 | 1kQ, +5%, % W Resistor | 110000-102 |
| R45 | 47 Q, +5%, v4 W Resistor | 110000-470 |
| R46, R47 | 1kQ, +5%, % W Resistor | 110000-102 |
| R49-R51 | 220 Q, +5%, v4 W Resistor | 410000-221 |
| R52 | 470 Q, +5%, % W Resistor | 110000-471 |
| R53 | 1kQ, +5%, % W Resistor | 110000-102 |
| R54 | 470 Q, +5%, Ys W Resistor | 410000-471 |
(Continued on next page)
*Acceptable substitute is part no. 137276-300
3-35
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R55, R56 | 1kQ, 5%, Y% W Resistor | 110000-102 |
| R57-R60 | 470 Q, +5%, V4 W Resistor | 110000-471 |
| R61 | 4.7 kQ, +5%, Vs W Resistor | 110000-472 |
| R62 | 10 kQ, +5%, v4 W Resistor | 110000-103 |
| R63 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R64 | 47 kQ, +5%, V4 W Resistor | 110000-473 |
| R65 | 4.7 kQ, +5%, Vs W Resistor | 110000-472 |
| R66 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R67 | 22 kQ, +5%, Vv W Resistor | 110000-223 |
| R68 | 47 kQ, +5%, Vs W Resistor | 110000-473 |
| R69 | 4.7 kQ, +5%, Vs W Resistor | 110000-472 |
| R70 | 10 kQ, +5%, v4 W Resistor | 110000-103 |
| R71 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R72 | 47 kQ, +5%, Ys W Resistor | 110000-473 |
| R73 | 4.7 kQ, +5%, V4 W Resistor | 110000-472 |
| R74 | 10 kQ2, +5%, %4 W Resistor | 110000-103 |
| R75 | 22 kQ, +5%, v4 W Resistor | 110000-472 |
| R76 | 47 kQ, +5%, v4 W Resistor | 110000-473 |
| R77-R80 | 1kQ, +5%, % W Resistor | 110000-102 |
| R81 | 220 2, +5%, 4 W Resistor | 110000-221 |
| R82 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R83 | 470 Q, +5%, v4 W Resistor | 110000-471 |
| RE4 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R85 | 2.2 kQ, +5%, v4 W Resistor | 110000-222 |
| R86 | 330 Q, +5%, Vs W Resistor | 110000-331 |
| R87 | 1kQ, +5%, Y4 W Resistor | 110000-102 |
| R88 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R89-R92 | 1kQ, +5%, % W Resistor | 110000-102 |
| R93, R94 | 330 2, +5%, % W Resistor | 110000-331 |
| R95 | 1kQ, +5%, ¥4 W Resistor | 110000-102 |
| ROE. | 4.7 kQ, +5%, V4 W Resistor | 110000-472 |
| R97 | 220 2, +5%, % W Resistor | 110000-221 |
| ROB | 2.2 kQ, +5%, v W Resistor | 110000-222 |
| R99 | 220 2, +5%, V4 W Resistor | 110000-221 |
| R101 | 2.2 kQ, +5%, Vs W Resistor | 110000-222 |
| R102, R104 | 1kQ, +5%, % W Resistor | 110000-102 |
| R103, R107 | 4.7 kQ, +5%, Ys W Resistor | 110000-472 |
| R106, R108-R115 | 1kQ, +5%, % W Resistor | 110000-102 |
| R116 | 1.5 kQ, +5%, v4 W Resistor | 110000-152 |
| R117 | 1kQ, +5%, % W Resistor | 110000-102 |
| R118 | 4.7 kQ, +5%, % W Resistor | 110000-472 |
| R119 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R120, R121 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R122 | 120 kQ, +5%, v4 W Resistor | 110000-124 |
| R123 | 470 Q, +5%, V% W Resistor | 110000-471 |
| R124 | 47 kQ, +5%, v4 W Resistor | 110000-473 |
| R125 | 12 kQ, +5%, “4 W Resistor | 110000-123 |
| R126 | 4.7 kQ, +5%, V4 W Resistor | 110000-472 |
(Continued on next page)
3-36
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R127, R128 | 2.2 kQ, +5%, Va W Resistor | 110000-222 |
| R129, R130 | 3.3 kQ, +5%, 4 W Resistor | 110000-332, |
| R131 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R132 | 22 kQ, +5%, 4 W Resistor | 110000-223 |
| A133 | 15 kQ, +5%, vs W Resistor | 110000-153 |
| R134 | 120 kQ, +5%, % W Resistor | 110000-124 |
| R135 | 470 Q, +5%, V4 W Resistor | 110000-471 |
| R136 | 47 kQ, + 5%, Vs W Resistor | 110000-473 |
| R137 | 15 kQ, +5%, % W Resistor | 110000-153 |
| R138 | 10 k2, +5%, % W Resistor | 110000-103 |
| R139 | 22 kQ, +5%, % W Resistor | 410000-223 |
| R140 | 180 k2, +5%, % W Resistor | 110000-184 |
| R141 | 470 Q, +5%, v4 W Resistor | 110000-471 |
| R142, R143 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R144-R151 | 1kQ, +5%, %4 W Resistor | 110000-102 |
| R152 | 47 kQ, +5%, Va W Resistor | 110000-473 |
| R153 | 470 Q, +5%, v4 W Resistor | 110000-471 |
| R154 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R155 | 82 kQ, +5%, % W Resistor | 110000-823 |
| R156, R157 | 47 kQ, +5%, % W Resistor | 110000-473 |
| R158 | 22 kQ, +5%, % W Resistor | 110000-223 |
| R159 | 47 kQ, +5%, “4 W Resistor | 110000-473 |
| Ri60 | 100 k2, +5%, % W Resistor | 110000-104 |
| R161-R165 | 2.2 kQ, +5%, % W Resistor | 110000-222 |
| R166 | 1kQ, +5%, % W Resistor | 110000-102 |
| R167 | 2.2 k2, +5%, Vs W Resistor | 110000-222 |
| R168 | 4.7 kQ, +5%, % W Resistor | 110000-472 |
| R169 | 220 kQ, + 5%, % W Resistor | 110000-224 |
| R170 | 380 kQ, +5%, % W Resistor | 110000-394 |
| R171 | 4.7 kQ, +5%, Vs W Resistor | 110000-472 |
| R172 | 15 kQ, +5%, %4 W Resistor | 110000-153 |
| R173 | 47 kQ, +5%, Vs W Resistor | 110000-473 |
| R174 | 33 kQ, +5%, 4 W Resistor | 110000-333 |
| R175 | 10 k2, +5%, % W Resistor | 110000-103 |
| R176 | 47 kQ, +5%, Y4 W Resistor | 110000-473 |
| R177 | 1kQ, +5%, Vs W Resistor | 110000-102 |
| R178 | 7.5 kQ, +5%, 4 W Resistor | 110000-752 |
| R179 | 330 kQ, +5%, % W Resistor | 110000-334 |
| R180, R181 | 47 kQ, +5%, 4 W Resistor | 110000-473 |
| R182 | 1kQ, +5%, % W Resistor | 110000-102 |
| R183 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R184 | 15 kQ, +5%, v4 W Resistor | 110000-153 |
| R185 | 10 k82, +5%, 4 W Resistor | 110000-103 |
| R186 | 1kQ, +5%, V% W Resistor | 110000-102 |
| R187 | 330 kQ, +5%, % W Resistor | 110000-334 |
| R188 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R189, R190 | 47 kQ, 5%, v4 W Resistor | 110000-473 |
| R191 | 1kQ, +5%, v4 W Resistor | 110000-102 |
(Continued on next page)
3-37
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R192 | 75 k8, +5%, Y% W Resistor | 110000-753 |
| R193 | 15 kQ, +5%, % W Resistor | 110000-153 |
| R194 | 47 kQ, +5%, Va W Resistor | 410000-473 |
| R195 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R196 | 1kQ, +5%, % W Resistor | 110000-102 |
| R197, R198 | 47 kQ, + 5%, Ya W Resistor | 110000-473 |
| R199 | 1kQ, +5%, % W Resistor | 110000-102 |
| R200 | 47 kQ, +5%, % W Resistor | 110000-473 |
| R201 | 15 k2, +5%, %4 W Resistor | 110000-153 |
| R202 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R203 | 1kQ, +5%, % W Resistor | 110000-102 |
| R204, R205 | 47 kQ, +5%, % W Resistor | 110000-473 |
| R206 | 1kQ, +5%, % W Resistor | 110000-102 |
| R207 | 20 k2, +5%, % W Resistor | 110000-203 |
| R208 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R209 | 20 kQ, +5%, % W Resistor | 410000-203 |
| R210 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R211 | 20 kQ, +5%, % W Resistor | 110000-203 |
| R212 | 10 kQ, 5%, % W Resistor | 110000-103 |
| R213 | 20 kQ, +5%, % W Resistor | 110000-203 |
| R214 | 10 kQ, +5%, V4 W Resistor | 110000-103 |
| R215 | 20 kQ, +5%, % W Resistor | 110000-203 |
| R216 | 10 kQ, +5%, ¥4 W Resistor | 410000-103 |
| R217 | 20 kQ, +5%, % W Resistor | 110000-203 |
| R218 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R219 | 20 k2, +5%, % W Resistor | 110000-203 |
| R220 | 27 kQ, +5%, % W Resistor | 110000-273 |
| R223 | 1kQ, +5%, v4 W Resistor | 110000-102 |
| R225-R231 | 1k2, +5%, % W Resistor | 110000-102 |
| R231-R238 | 2.2 k2, +5%, % W Resistor | 110000-222 |
| R239-R244 | 1k, +5%, ¥% W Resistor | 110000-102 |
| R245 | 100 2, +5%, %& W Resistor | 110000-101 |
| R246 | 150 kQ, + 5%, % W Resistor | 110000-154 |
| 4€ | 2.2 kQ, +2%, Dual-Inline-Package Resistor Network | 118003-222 |
| ON | 1kQ, +2%, Dual-inline-Package Resistor Network | 118003-102 |
Sockets
| 3A | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| 3E, 3F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| SL | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4E, 4F | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42028 |
| 4L | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4N | 40-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C40 |
(Continued on next page)
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 6H-9H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7D | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| TE, 7F | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 7H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7M | 28-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C28 |
| 8A | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 8c | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C628 |
| 9C | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 9E | 42-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C42 |
| OFA | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 9K | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C42 |
| 9M | 42-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C42 |
| 12E, 12F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
Switches
| BJA | 8-Station, Single-Throw, Dual-Inline-Package Bit Switch | 66-118PIT |
| OL | 8-Station, SingleThrow, Dual-Inline-Package Bit Switch | 66-118P IT |
Transistors
| Qi | Type-2N3906 40 V, 1 W, PNP Transistor | 33-2N3906 |
| Q2 | Type-2N3904 60 V, 350 mW, NPN Transistor | 34-2N3904, |
| Q3 | Type-MPS-A92 300 V, 500 mA, PNP Transistor | 33-MPSA92 |
| Q4 | Type-2N3904 60 V, 350 mW, NPN Transistor | 34-2N3904 |
| Q5, Q6 | Type-2N6044 80 V, 8 A, Darlington NPN Transistor | 34-2N6044 |
Miscellaneous
| BT1 | 3.6 V, 100 mA Nickel-Cadmium Battery | 171028-001 |
| Wi | Lead-Spring Socket Terminal | 179131-001 |
Test Point Acceptable substitute is part no. 020670-01 179051-001 Jumper Staple 150009-001
| Q5, Q6 | Nylon Snap-In Fastener | 81-4302 |
3-39
Pole Position
eae 225 = Era] SS aad 98 fesse] tases] i u
263) foros) Ser] Maintenance, Repair, and Parts
= TEI Cazes | Toss) Sisgs7] fleas re) aaa] gies) Somes) ess 7 J BS = rss] Eesne sd Ress] fe] 6 10
Figure 3-17 Pole Position Video Printed-Circuit Board Assembly A039187-21 B
3-40
Pole Position Maintenance, Repair, and Parts.
Pole Position Video Printed-Circuit Board Assembly Parts List
| Designator | Description | Part No. |
Capacitors
| c2 | 470 uF, 25 V Aluminum Electrolytic Axial-Lead Capacitor | 24-250477 |
C3-C17 22 uF, 16 V Aluminum Electrolytic Axial-Lead Capacitor Acceptable substitute is part no. 24-250226 24-160226
| C18-C57 | 0.1 uF, + 80, -20%, 50 V Ceramic Disk Radial-Lead Capacitor | 122002-104 |
| C58 | 68 pF, 100 V, Mica Capacitor | 128002-680 |
| C59 | 22 pF, 100 V, Mica Capacitor | 128002-220 |
Diodes
| CR1 | Type-MV5053 Light-Emitting Diode | 38-MV5053 |
| CcR2 | Type-1N4735A, 6.2 V, 1 W Zener Diode | 131009-001 |
Inductors
| L1-L3 | 1 uH, ¥2 W Inductor | 141007-001 |
| 4 | 100 uH, + 10% Inductor | 141002-001 |
Integrated Circuits
| 2a | Type-74LS138 Integrated Circuit | 137177-001 |
| 2E | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 2H | Type-74LS139 Integrated Circuit | 37-74LS139 |
| 2d | Type-74LS10 Integrated Circuit | 37-74LS10 |
| 2K | Type-74LS368 Integrated Circuit | 137168-001 |
| 3B | Type-74LS283 Integrated Circuit | 137204-001 |
| 3G | Type-74LS283 Integrated Circuit | 137204-001 |
| 3D | Type-74LS283 Integrated Circuit | 137204001 |
| 3H | Type-74LS175 Integrated Circuit | 37-74LS175, |
| SU, 4d | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 3K | Type-74LS283 Integrated Circuit | 137204001 |
| 3L | Type-74LS283 Integrated Circuit | 137204001 |
| 3M | Type-74LS02 Integrated Circuit | 37-74LS02 |
| 4B | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 4c | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 4H | Type-74LS157 Integrated Circuit | 37-74LS157 |
| 4K | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 4M, 5M | Type-74LS298 Integrated Circuit | 137201-001 |
| 4N, 5N | Type-74LS283 Integrated Circuit | 137204-001 |
| 5B | Type-74LS174 Integrated Circuit | 37-7ALS174 |
| 5C | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 5D | Type-74LS174 Integrated Circuit | 37-74LS 174 |
| 5E | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 5F, 6F | Type-74LS245 Integrated Circuit | 37-74LS245, |
| 5H | Type-74LS175 Integrated Circuit | 37-74LS175 |
| 5d | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 6A | Type-74S04 Integrated Circuit | 37-74504 |
| 6B | Type-74LS368 Integrated Circuit | 137168-001 |
| 6C | Type-74LS08 Integrated Circuit | 37-74LS08 |
| 6H | Type-74LS245 Integrated Circuit | 37-74LS245 |
| bu | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 6K | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 6M, 7M | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 7B | Type-74S163 Integrated Circuit Acceptable substitute is part no. | 137274-001 |
137287-001 or -002
| 7c | Type-74S04 Integrated Circuit | 37-74S04 |
| 70 | Type-74LS32 Integrated Circuit | 37-74LS32 |
(Continued on next page)
3-41
Maintenance, Repair, and Parts
Pole Position Video Printed-Circuit Board Assembly Parts List, continued Pole Position
| Designator | Description | Part No. |
| 7L | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 8B | Type-74S00 Integrated Circuit | 37-74S00 |
| 8C,9C | Type-74LS157 integrated Circuit | 37-74LS 157 |
| 8D | Type-74LS158 Integrated Circuit | 137203-001 |
| 8E | Type-74LS158 Integrated Circuit | 137203-001 |
| 8L,9L | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 9B | Type-74LS20 Integrated Circuit | 37-74LS20 |
| 9D | Type-74LS298 Integrated Circuit | 137201-001 |
| QE, 10E | Type-74LS257 Integrated Circuit | 37-74LS257 |
| 9H | Type-74S 161 Integrated Circuit | 137287-001 |
| od | Type-74S161 Integrated Circuit | 137287-001 |
| 9K | Type-7497 Integrated Circuit | 37-7497 |
| 9M, 10M | Type-74LS283 Integrated Circuit | 137204-001 |
| ON | Type-74LS85 Integrated Circuit | 37-74LS85 |
| 10B | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 10C | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 10D | Type-74LS368 Integrated Circuit | 137168-001 |
| 10H | Type-74S161 Integrated Circuit | 137287-001 |
| 10J | Type-74S161 Integrated Circuit | 137287-001 |
| 10K | Type-74S161 Integrated Circuit | 137287-001 |
| 10L | Type-74S 161 integrated Circuit | 137287-001 |
| 10N | Type-74LS85 Integrated Circuit | 37-74LS85 |
| 1B | Type-74107 Integrated Circuit Acceptable substitute is part no. | 37-74107 |
137169-001
| qIF | Type-74LS174 Integrated Circuit | 37-74LS 174 |
| 11H | Type-74LS174 Integrated Circuit | 37-74LS174 |
| Wd | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 11K | Type-74LS139 Integrated Circuit | 37-74LS 139 |
| TL | Type-74L$373 Integrated Circuit | 37-74LS373 |
| 11M | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 12B | Type-74LS08 Integrated Circuit | 37-74LS08 |
| 12F | Type-74LS86 Integrated Circuit | 37-74LS86 |
| 13F | Type-74LS20 integrated Circuit | 37-74LS20 |
For -21 version only
| 2F | Type-07 Custom Integrated Circuit | 137193-001 |
| 3N | Type-02 Custom integrated Circuit | 137190-001 |
| 4D | Type-09 Custom Integrated Circuit | 137282-001 |
| SL, 6L | Type-03 Custom Integrated Circuit | 137283-001 |
| 7E | Type-04 Custom Integrated Circuit | 137191-001 |
| 8N | Type-02 Custom Integrated Circuit | 137190-001 |
| 13H | Type-02 Custom Integrated Circuit | 137190-001 |
Random-Access Memories
| 3E, 4E | Random-Access Memory (200 ns) Acceptable substitute is part no. | 137198-001 |
137211-001 (150 ns)
| 3F, 4F | Random-Access Memory (200 ns) Acceptable substitute is part no. | 137198-001 |
137211-001 (150 ns)
| 7F, 8F | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7H, 8H | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7J, BJ | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7K, 8K | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| OF, 10F | 55 ns Random-Access Memory | 137199-001 |
(Continued on next page)
Pole Position Maintenance, Repair, and Parts
Pole Position Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
Programmable Read-Only Memories
| 2B | Type-82S 129(17) Programmable Read-Only Memory | 136014-144 |
| 26 | Type-82S129(16) Programmable Read-Only Memory | 136014-143 |
| 2D | Type-82S129(15) Programmable Read-Only Memory | 136014-142 |
| 4u | Type-82S 137(12) Programmable Read-Only Memory | 136014-145, |
| 5K | Type-82S 129(11) Programmable Read-Only Memory | 136014-141 |
| 6D | Type-82S 123(14) Programmable Read-Only Memory | 136014-136 |
| 6E | Type-82S 123(13) Programmable Read-Only Memory | 136014-135 |
| 8M | Type-82S129(10) Programmable Read-Only Memory | 136014-140 |
| 110 | Type-82S129(9) Programmable Read-Only Memory | 136014-139 |
| 1D | Type-82S 129(8) Programmable Read-Only Memory | 136014-138 |
| TE | Type-82S 1297) Programmable Read-Only Memory | 136014-137 |
| 12H | Type-82S137(6) Programmable Read-Only Memory | 136014-146 |
For -21 version only
| 2L | Electrically Programmable Read-Only Memory Acceptable | 136014-127 |
substitute is part no. 136014-158
| 2M | Electrically Programmable Read-Only Memory Acceptable | 136014-128 |
substitute is part no. 136014-159
| 2N | Electrically Programmable Read-Only Memory | Acceptable | 136014-134 |
substitute is part no. 137205-001
| 6N | Electrically Programmable Read-Only Memory | Acceptable | 136014-133 |
Substitute is part no. 137205-001
| 7N | Electrically Programmable Read-Only Memory | Acceptable | 136014-132 |
Substitute is part no. 137205-001
| TiN | Electrically Programmable Read-Only Memory Acceptable | 136014-231 |
substitute is part no. 136014-131
| 12d | Electrically Programmable Read-Only Memory Acceptable | 136014-120 |
substitute is part no. 136014-151
| 12K | Electrically Programmable Read-Only Memory Acceptable | 136014-122 |
substitute is part no. 136014-153
| 12L | Electrically Programmable Read-Only Memory Acceptable | 136014-124 |
substitute is part no. 136014-155
| 12N | Electrically Programmable Read-Only Memory Acceptable | 136014-126 |
substitute is part no. 136014-157
| 13J | Electrically Programmable Read-Only Memory Acceptable | 136014-119 |
substitute is part no. 136014-150
| 13K | Electrically Programmable Read-Only Memory Acceptable | 136014-121 |
substitute is part no. 136014-152
| 13L | Electrically Programmable Read-Only Memory Acceptable | 136014-123 |
substitute is part no. 136014-154
| 13N | Electrically Programmable Read-Only Memory Acceptable | 136014-125 |
substitute is part no. 136014-156 Resistors
| R1-R9 | 2.2 kQ, +5%, V4 W Resistor | 110000-222 |
| R10-R24 | 1kQ, +5%, % W Resistor | 110000-102 |
| R25-R40 | 470 2, +5%, % W Resistor | 110000-471 |
| R41-R48 | 4.7 kQ, +5%, V4 W Resistor | 110000-472 |
| R49-R52 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R55-R58 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R59 | 220 2, +5%, Vs W Resistor | 110000-221 |
| R60 | 470 2, +5%, V4 W Resistor | 110000-471 |
(Continued on next page)
3-43
Maintenance, Repair, and Parts Pole Position
Pole Position Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R61 | 1k, +5%, % W Resistor | 110000-102 |
| R62 | 2.2 kQ, +5%, v4 W Resistor | 110000-222 |
| R66 | 220 Q, +5%, v4 W Resistor | 110000-221 |
| R67 | 470 2, +5%, v4 W Resistor | 110000-471 |
| R68. | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R69 | 2.2 kQ, +5%, V4 W Resistor | 110000-222 |
| R73 | 220 Q, +5%, % W Resistor | 110000-221 |
| R74 | 470 2, +5%, Y W Resistor | 110000-471 |
| R75 | 1kQ, +5%, % W Resistor | 110000-102 |
| R76 | 2.2 kQ, +5%, v4 W Resistor | 110000-222 |
| R80 | 1kQ, +5%, % W Resistor | 110000-102 |
| R81 | 100 2, +5%, % W Resistor | 110000-101 |
| R82-R85 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R86 | 220 2, +5%, v4 W Resistor | 110000-221 |
| R87-R98 | 1kQ +5%, V4 W Resistor | 110000-102 |
| R99 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R100 | 220 2, +5%, V4 W Resistor | 110000-221 |
| R101 | 10 k2, +5%, % W Resistor | 110000-103 |
| R102 | 1.5 kQ, +5%, 4 W Resistor | 110000-152 |
| R103-R105 | 82 Q, +5%, % W Resistor | 110000-820 |
| 1B | 2.2 kQ, +2%, 15-Element, Dual-inline Package Resistor Pack | 118003-222 |
| 1K | 2.2 kQ, +2%, 15-Element, Dual-Inline Package Resistor Pack | 118003-222 |
Sockets
| 2F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| aL | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 2M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 2N | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 3E, 4E | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| SF, 4F | 24-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C24 |
| 3N | 28-Contact Medium-insertion-Force integrated Circuit Socket | 79-42C28 |
| 4D | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42624 |
| 5L, 6L | 18-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C18 |
| 6N, 7N | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 7E | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 8N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 11N | 24-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C24 |
| 12J, 13d | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12K, 13K | 28-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C28 |
| 12L, 13L | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12N, 13N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 13H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
Transistor
| Q4 | Type-2N3904, 60 V, 1 W, NPN Transistor | 34-2N3904 |
Miscellaneous Test Points Acceptable substitute is part no. 020670-01 179051-002
| Y1B | 24.576 MHz Crystal Acceptable substitute is part no. 144004-002 | 144004-003 |
Pole Position
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spectlie written permission of Atari, Ine., Sunnyvale, CA. This drawing is only condttionaly issued, ‘and ‘neither receipt nor possession theteof confers or vansters any right in, of Acense to use, the subject malter of the drawing ox any design or technical intorrnation shown thereon, nor any right fo reproduce this drawing or any part thereo!, Except for manufacture by vendors of Atari Inc., and for manulacture ander ine covporation’s written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permis sian from the corporation, Maintenance, Repair, and Parts
Gare
clo S300uF + 35V
C3
Figure 3-18 Regulator/Audio Il PCB Assembly U.S.-Built Cabinet A035435-01 G
Maintenance, Repair, and Parts
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This ‘drawing is only conditionally issued, and neither receipt nor possession thereo! conters or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any fight to reproduce this drawing or any part thereo!. Except for manufacture by vendors of Atari, Inc., and for manufac ture under the corporation's written license, no right to reproduce this drawing 1s granted or the Subject matter thereo! unless by written agreement with or written permis: sion from the corporation. Pole Position
R241, 7W!
Figure 3-19 Regulator/Audio II PCB Assembly lreland-Built Cabinet A035435-05 A
3-46
Pole Position Maintenance, Repair, and Parts
Regulator/Audio || PCB Assembly Parts List
Assemblies and components in the following parts list are shown in Figures 3-18 and 3-19.
| Designator | Description | Part No. |
Capacitors
For -01* and -05** versions
| C1 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| c2 | 0.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| C8 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C13 | 1000 yF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250108 |
For -01 version
| C3 | 0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 29-088 |
| C4 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C5 | 0.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable | 100015-103 |
substitute is part no. 122005-103
| cé | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| c7 | 0.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| C9, C10 | 3300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-350338, |
| ci | 0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 29-088 |
| C12 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C14 | 0.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable | 100015-103 |
substitute is part no. 122005-103
| C15 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C16 | 0.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| Ci7 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C18, C19 | 3300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-350338 |
| C20, C21 | 0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 29-088 |
| C22, C23 | 1 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-500105 |
Diodes
For -01 and -05 versions
| CRI | Type-1N4002, 1 A, 100 V Silicon Rectifier Diode | 31-1N4002 |
| CR4 | Type-1N4002, 1 A, 100 V Silicon Rectifier Diode | 31-1N4002 |
Integrated Circuits
For -01 and -05 versions
| Qi | Type-LM305, 5 V, Linear Voltage Regulator | 37-LM305 |
For -01 version
| Qs | Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit | 137151-002 |
| Q7 | Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit | 137151-002 |
(Continued on next page)
*Acceptable substitutes are A035435-02 or -04. **Acceptable substitutes are A035435-01, -02, or -04.
Maintenance, Repair, and Parts Pole Position
Regulator/Audio || PCB Assembly Parts List, continued
| Designator | Description | Part No. |
Resistors
For -01 and -05 versions
| R1 | 270 2, +5%, Ya W Resistor | 110000-271 |
| R3 | 33 Q, + 5%, % W Resistor | 110000-330 |
| R4 | 100 2, +5%, VY W Resistor | 110000-101 |
| RS | 2.7.9, +5%, 1 W Resistor | 110009-027 |
| RE | 3.9 kQ, +5%, Ys W Resistor | 110000-392 |
| R7 | 7.5 kQ, +5%, V4 W Resistor | 110000-752 |
| R8 | 1 kQ Vertical PCB-Mounting Cermet Potentiometer Acceptable | 19-315102 |
substitute is part no. 119002-102
| R24 | 0.1 2, +3%, 7 W Wirewound Resistor | 19-100P 1015 |
| R29, R30 | 10 Q, +5%, % W Resistor | 110000-100 |
For -01 version
| RQ | 220 2, + 5%, V2 W Resistor | 110001-221 |
| R10 | 12, 5%, Ys W Resistor | 110000-010 |
| R11 | 10 2, +5%, % W Resistor | 110000-100 |
| R12 | 100 2, +5%, % W Resistor | 110000-101 |
| R13, R14 | 10 kK, +5%, % W Resistor | 110000-103 |
| R19 | 1Q, +5%, v4 W Resistor | 110000-010 |
| R20 | 10 Q, + 5%, % W Resistor | 110000-100 |
| R21 | 220 Q, +5%, v2 W Resistor | 110001-221 |
| R22 | 100 2, +5%, Ya W Resistor | 110000-101 |
| R27, R28 | 1 kQ, +5%, % W Resistor | 110000-102 |
Transistors
For -01 and -05 versions
| Q2 | Type-TIP32 PNP Power Transistor | 33-TIP32 |
| Q3 | Type-2N3055 NPN Silicon Transistor | 34-2N3055 |
Mechanical Parts
For -01 and -05 versions
| J6 | 6-Position Connector Receptacle | 79-58306 |
| u7 | 9-Position Connector Receptacle | 79-58308 |
| Q3 | #6-32 x Y2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel | 72-1608C |
Machine Screw
| Q2, Q3 | #6-32 Nut/Washer Assembly | 75-995 16 |
| Q2 | Thermally Conductive Silicon Insulator | 78-16014 |
| Q3 | Thermally Conductive Silicon Insulator | 78-16008 |
| Qs | #6-32 x %-Inch Binder-Head Nylon Screw | 75-F60405 |
Heat Sink 034531-01 Test Point Acceptable substitute is part no. 020670-01 179051-001
For -01 version
| J8 | 4-Position Connector Receptacle | 79-58354 |
| Qs | #6 x %Inch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc- | 72-6606S |
Plated-Steel Screw
Pole Position
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, inc,, Sunnyvale, CA, This drawing is only conditionally issued, and neither receipt nor possession thereof confers ar vansfers any right in, of license to use, the subject matter of the drawing or any design or technical inforation shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Alafi, Inc., and for manulacture under the corporation's written license, no right to reproduce this drawing 's granted or the subject matter thereo! uniess by written agreement with or written permission from the corporation
On Maintenance, Repair, and Parts
peeeecnett
errci2 Coe'3 Citciwm ocs Cai cie Goa7 fal f
oc Prmto cs Goca3 C3-644,470PF tecas (cae 470FF 3647 ,.270Fe Goce
Gocs4 cocss f
fl
Figure 3-20 EMI Shield PCB Assembly A037667-01 A
Maintenance, Repair, and Parts Pole Position
EMI Shield PCB Assembly Parts List
Components in the following parts list are shown in Figure 3-20.
| Designator | Description | Part No. |
Capacitors
| C1-C5 | 0.1 yF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C6-C10 | 0.01 pF, + 80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C12 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C13-C15 | 0.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C16 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C17-C24 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C25 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C27-C31 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| 32,633 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C34-C39 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C40-C43 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C44 | 0.471 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-471 |
| C45 | 0.001 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-102 |
| C46,C47 | 0.471 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-471 |
| C48 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C54,C55 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
Connectors
| P19 | 30-Pin Card-Edge Connector Acceptable substitute is part no. 179046-030 | 179073-030 |
| P20 | 44-Pin Card-Edge Connector Acceptable substitute is part no. 179046-044 | 179073-044 |
3-50
Pole Position Maintenance, Repair, and Parts
H. Power Supply Assembly
A021084-xx (Voltage plugs)
29.083 Fy : (Capacitor) : Y 034544-01 : ! (Fuse block cover)
79-4411001 (Fuse post) 78-70501SC. ' (Capacitor bracket) 46-2017002 (Fuse)
29-053 (Capacitor) A035891-02 Worse (Fuse harness assy) <2 46-301 = (Fuse)
037639-01 (Label) yy
= 78-2708 | (== (Bushing) 5
A034630-01 (Filter Assy ) 79-3206 (Fuse block) 037641-01 78:70801SC ree 46-2014002 (Bracket) (Fuses)
A035890-01 \ (Power harness) A034629-01 {AC harness) 79-15021001 (Terminal block)
3A-MDA3501 (Rectifier)
Figure 3-21 Power Supply Assembly A037671-04 & -05 G
3-51
Maintenance, Repair, and Parts Pole Position
Power Supply Assembly Parts List
Assemblies and components in this parts list are shown in Figure 321.
Part No. Description (Reference Designations in Bold)
| A021084-01 | Voltage Plug for 100V | (90-110 VAC) (violet) | |
| A021084-02 | Voltage Plug for 120V | (105-135 VAC) (yellow) | |
| A021084-04 | Voltage Plug for 220V | (200-240 VAC) | (b/ue) |
| 02108405 | Voltage Plug for 240V | (220-260 VAC) (brown) |
A034629-01 AC Harness Assembly
| A034630-01 | RFI Filter Assembly | (FL1—designation not marked) |
A036888-01 Upright and Cabaret Transformer Assembly (11) Acceptable substitute is part no. A035888-02 A035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6) 29-053 27,000 uF 15V DC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1) 46-2014002 4A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F2, F4-F6) 462017002 7 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301253 25 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %,-Inch Outside Diameter x ‘%-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket (C1) 79-15021001 2Circuit Single-Row Terminal Block (located under F4) 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals (F2-F6) 79-441 1001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post (F1) 03448202 Power Supply Chassis
| 034544-01 | Fuse Block Cover | (F2-F6) |
| 037639-03, -04 | Label for Fuse Value | (F1) |
| 037641-01 | Label for Fuse Values | (F2-F6) |
‘A037671-04 power supply has the 120 V plug. A037671-05 has the 100 V, 220 V and 240 V plugs. A03767 1-06 has the 220 V and 240 V plugs.
3-52
Pole Position
Glossary of Terms
AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for START is low.
ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as Jong as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating the coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT . A binary digit; expressed as a 1 or aod. BLANKING Turning off the beam on a cathoderay tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER
- An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
- A device used to supply additional drive capability. BUS An elecirical path over which information is transferred from any of several sources to any of several destinations.
CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass.
CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice.
CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6digit electro-mechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. Glossary
COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. pc Direct current, meaning current flow: ing in one direction and of a fixed value. DEFLECTION YOKE Electro-magnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage.
Gut
Glossary
GATE
- A circuit with one output that responds when and only when a certain combination of pulses is present at the inputs.
- Acircuit in which one signal switches another signal on and off. 3, To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbois 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube. ie) Input/Output. imRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond, LED The abbreviation for a light-emitting diode, LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic elernent or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the togic states (levels) ina TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area {Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4VDC to +5 VDC MULTIPLEXER A device that takes several lowspeed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line.
GL2 NMI Non-maskable interrupt. NMI is a request for service by the micro- Processor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER
- A resistor that has a continuously moving contact which is generally mounted on a moving shatt. Used chiefly as a voltage divider. Also called a pot (slang).
- An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the ternporary storage of data. RASTER-SCAN DISPLAY A dispiay systern whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controis the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathoderay tube electron beam is resetting either from right to left or from bot: tom to top. RESISTOR Adevice designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment Called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit Pole Position
strearns into four-digit hexadecimai signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circult designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY Adisplay system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
Pole Position 3rd printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm (1 Distributor
Address O Operator
City State Zip - O Other. _
Area Code Phone
First fold
No Postage Necessary mailed in the United States
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Attn.: Field Service/Coin-Op Division P. O. Box 427 a a as
Atari, Inc. es
Ce Sunnyvale, California 94086 Pe Dn a
Second fold
Wold aBpa siy) ade, 4
Pole Position 3rd printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm _. CO Distributor
Address. Ci Operator City State Zip 0 Other. Area Code Phone
First fold
Atari Ireland Limited Attn.: Field Service/Coin-Op Division
Tipperary Town, Ireland
Attach Necessary Postage
Second fold
eBpe si) edey WOs4
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GE PE GE PE ES,
> > > > >
Fdsee Nil Natee Nah | Satee, ae! Sata Nated
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant, and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. iz « © % ©
© = AN
ATARI, INC. 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488