CATHODE RAY TOMES

ATV Track

ATV Track (set 1) (Gaelco, 2002) · Manual · 92 pages · 18 sections · original scan

Page 1

ATRAC

OPERATOR’S MANUAL

=)

© GAELCO 2002

IT IS THE RESPONSIBILITY OF THE OPERATOR TO CARE ABOUT COSTUMER SAFETY AT ALL TIMES. PLEASE READ AND OBSERVE THE NOTES ON SAFETY DESCRIBED IN THIS MANUAL.

Page 2

About ATV TRACK

Thank you for purchasing this Gaelco S.A. product. This manual explains how to safely operate your game machine. Failing to operate the machine correctly could result in malfunction or accident, so please read the manual carefully before starting operation, specially the SAFETY NOTES (Section 3).

Unauthorised reproduction of this document or any of its contents is strictly forbidden, without permission from Gaelco S.A.

Note: Operator's Manual Specifications are subject to change without prior notice

© 2002 Gaelco S.A. - All rights reserved

Copyright law and industrial property law protect the contents of this game, its main data and design.

ATV TRACK has been manufactured in accordance with European Community directives. Any changes or modifications to this machine has to be authorised by Gaelco S.A. and must be in accordance with the European Community directives. Using spear parts that do not fit specifications will void the warranty. Removal of serial numbers and/or bar codes from product or components will void the warranty.

Published by: GAELCO S.A. Escipion 11 08023 Barcelona - SPAIN Tel. ++34 93 417 36 26 Fax ++34 93 417 28 02 e-mail gaelco@gaelco.com web www.gaelco.es

FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part A of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operating in a commercial environment. This equipment uses, and can radiate radio frequency energy, if not installed and used according to the instruction manual, and may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Page 3

1.1 1.2 1.3 1.4

3.1 3.2 3.3 3.4 3.5

4.2 4.3

5.1 5.2 5.3 5.4

6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 INDEX

GENERAL INFORMATION Manufacturer and Machine data Legislation references Technical Service Responsibility

MACHINE SPECIFICATIONS

SAFETY NOTES General considerations Location Moving the machine Operation Motion system

MATERIAL HANDLING Transport of the packaged units Storage Reception

UNPACKING, ASSEMBLING AND INSTALLATION Inspection before assembling Assembling Installation Switching on the machine

TEST MODE AND PROGRAMMATION Screen test Input / Output test Motion System test Settings Sound test Book Keeping Transfer of the program version Exit

HOW TO PLAY Competition on link mode

HOW TO LINK TWO MACHINES

  • TECHNICAL SERVICE 9.1 Prior considerations 9.2 Safety precautions 9.3. Brake light 9.4 Handlebar mechanism 9.5 Emergency and safety stops 9.6 Position of the brake levers and the throttle 9.7 Disassembling and assembling the throttle 9.8 Adjusting the acceleration potentiometer 9.9 Partial dissasembly of the protection hood 9.10 Checking position potentiometers 9.11 Asynchronous motors - Circuit diagram 9.12 Checking the Commander SE parameters 9.13 Troubleshooting
  • PARTS LIST MONITOR CABINET. 10.1 Monitor subwoofer & accessories 10.2 Service panel, coin door & speakers 10.3 Control panel & cash box 10.4 Plastics and accessories 10.5 Billboard assembly 10.6 Base covers 10.7 Base parts 10.8 Control parts PLATFORM 10.9 Main assemblies 10.10 Design related parts 10.11 Parts on top 10.12 Steering assembly 10.13 Handlebar assembly 10.14 Throttle assemby 10.15 to 10.18 Steering mechanism 10.19 Mobile platform assembly 10.20 Rider footrest assembly 10.21 Main structure 10.22 Motion Mechanism
  • WIRING DIAGRAMS
  • CREDIT DISTRIBUTOR SETUP
Page 4

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 5
  • GENERAL INFORMATION

1.1 MANUFACTURER AND MACHINE DATA

Manufacturer GAELCO, S.A. Address Escipion 11 ZIP 08023

City Barcelona

Country : SPAIN Tel. 34 93 417 36 26 Fax 34 93 417 28 02 e-mail gaelco@gaelco.com

Name of the game ATV TRACK

Model MOTION

1.2__LEGISLATION REFERENCES

EM EMISSION

EN 61000-3-2 (1995), Harmonics EN 61000-3-3 (1995), Fluctuations EN 55022 (1994), Continuous conducted emission (Class A) EN 55022 (1994), Radiated emission (Class A)

EM IMMUNITY

EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 (1996), RF common mode EN 61000-4-8 (1993), 50 Hz H-field EN 61000-4-11 (1994), Dips, interruptions 1995 1996 1995 1995 , ESD & ENV 50204 (1995), Radiated field of RF , EFT burst , Surges

ELECTRICAL SAFETY

UNE EN 60335-1 (1997) + Erratum (1997) + A11 (1997) + A12 (1997) + A13 (1999) + A14 (1999) + Erratum (1999).

Note: Test passed in Motion Test mode
Page 6

1.3__TECHNICAL SERVICE

Gaelco S.A. or its Distributors carry out technical Service.

1.4 RESPONSIBILITY

Any modifications made to this machine that are not authorised in writing by the manufacturer will be considered to be at the exclusive responsibility of the operator, who will consequently become the new "manufacturer" and must operate in compliance with the European Community directives. In case of an accident caused by a defective part, the manufacturer will assume responsibility only if the machine was defective in its original condition. However, this responsibility shall be diminished or even totally annulled if the operator or the player do not follow the instructions provided or if the operator uses spare parts that are not covered by guarantee, are not authorised in writing or do not correspond to the specified technical characteristics.

  • SPECIFICATIONS

GAME DESCRIPTION

ATV TRACK is an arcade game that challenges the player's ability to ride a QUAD through a course plenty of natural obstacles, by using a handlebar with throttle and two brake levers. The goal of the player is to complete in succession the four phases of the game. The MOTION model of the ATV TRACK game machine is powered by an electric motion system that delivers very realistic sensations to the player. Two players can also compete one against each other when the machines are linked.

DIMENSIONS AND WEIGHT

  • Crate dimensions and shipping weight of each module
widthdepthheightweight
Monitor cabinet990 mm1190 mm1920 mm205 Kg
Seat platform990 mm1190 mm1300 mm240 Kg
  • Dimensions and net weight of each module unpacked
widthdepthheightweight
Monitor cabinet870 mm970 mm1760 mm*190 Kg
Platform880 mm1150 mm1250 mm225 Kg
  • Without the billboard
Page 7
  • Total dimensions of the machine, installed on site

width depth height 880 mm 2356 mm 2135 mm

POWER SUPPLY

Operating Power: 220-230 VAC, 50 Hz Output: +5VDC 20A, +12VDC 8A

MONITOR

34" Hantarex Polo/2 STAR PH, code 01297790

CPU BOARD

PCB Gaelco ATV TRACK

CONTROLS

Interactive handlebar Start Button/View change (placed on the throttle) Throttle (accelerator grip) Right brake lever Left brake lever Emergency Stop button (placed on top of the fuel tank) Safety Stop system (activated when the rider footrest are not pressed)

PCB Gaelco ATV TRACK

MOTION SYSTEM

Degrees of freedom: 2 DOF Actuators: 2 induction motors (geared), 0.75KW each Control: 2 frequency inverters SE1120075, input voltage 230V +/-10%, 50/60Hz

ATTACHMENTS

Operator's Manual Motor driver manual Monitor Manual Coin box keys Monitor cabinet keys Power cord (3m long) Link cable Monitor cable (remote control)

Page 8
  • SAFETY NOTES

In order to use this machine safely please read carefully this Manual BEFORE the installation, use or maintenance of the machine.

This Operator's Manual and others manuals delivered with the machine must be available to the operating and service personnel.

When transporting or reselling the machine, be sure to attach this Manual.

The ATV TRACK machine has been designed for indoor use only, within residential or commercial areas, and must be used exclusively for the purpose intended.

GAELCO S.A. bears no responsibility for accidents, injury or damage resulting for unauthorized changes or improper use of the machine.

WARNING

To avoid accidents or damages, it is imperative to follow the notes on Safety resumed bellow, as well as all those included in the following sections:

SECTION 4. MATERIAL HANDLING SECTION 5. UNPACKING, ASSEMBLING & INSTALLATION SECTION 9. TECHNICAL SERVICE

Page 9

3.1__GENERAL SAFETY CONSIDERATIONS

AN

e Before operating the machine, check that it has been installed correctly and in accordance with this Manual.

e As some parts of the machine move during game play, there are places where the distance between the stationary section and the mobile section changes. Despite the measures implemented to avoid accidents, if the operator feels that a person is in any

danger, he should warn that person or stop the machine immediately by using the Emergency Stop button.

@ The warning notices (stickers) must be kept in such condition that customers can read them easily.

e Installation, service or routine maintenance should be carried out by qualified personnel.

e Before connecting the machine to the mains supply, verify that it is set for the correct voltage and that the proper fuses are already installed.

e@ When replacing fuses, use spare fuses of the same type and rating than the originals. The use of other material can cause serious damages on the electronic circuits or even a fire hazard. Check the Parts List to know the exact specifications.

@ The machine includes areas of high voltage. Care must be taken at all times to avoid electrical shock whenever inspecting or adjusting the equipment, particularly around the monitor.

@ To ensure safe operation, the machine must be grounded with a plug securely connected to Earth.

© Do not turn ON the power switch until the machine has been installed on its dedicated place.

If there is any error or problem with this machine, operation must be stopped immediately.

Page 10

3.2__ SAFETY PRECAUTIONS CONCERNING LOCATION

aN

Do not place the machine where it might be an obstacle in case on emergency (i.e. close to fire extinguishers or emergency exits).

Install and operate the machine in places where appropriate lighting is available, so

warning labels can be clearly read by the customers.

This machine has been for indoor use only, within residential or commercial spaces. Absolutely do not set up the machine outdoors or under the following conditions:

e Direct exposure to sunlight, high humidity, water contact, dust, high heat or extreme cold.

e In locations near containers holding liquids or liquid dispensing equipment. In general, precautions should be taken against spilling liquids of any kind whatsoever over the machine

e Ina place exposed to vibration. The machine must be installed on a level surface with levellers properly adjusted.

@ In locations near ventilating holes. Doing so could cause internal temperature to rise excessively, resulting in equipment failure.

e Near hazardous substances

Furthermore:

e In order to have easy access to the PSU, CPU and control devices, please make sure that the rear an sides of the machine are separated from the wall or other machines by at least 300mm (12")

e Ventilation slots must be not obstructed, and the machine must be positioned so as to leave a distance of at least 100mm (4") from possible obstructions

© Do not run the power cord across passages where pedestrian's feet could get caught on the cord.

e Ensure that the location’s power supply is equipped with an Earth Leakage Breaker rated at 30mA.

GAELCO shall not be held responsible for any damage resulting from the failure to observe these instructions.

Page 11

3.2.1 SECURING IN PLACE

Ensure that all the leg levellers make firm contact with the surface of the floor. This precaution is crucial for the ATV-TRACK version with motion system, because the machine can move of itself, causing an accident.

After making the adjustment of all legs, secure the height of each one by fastening upward the nut.

CASTOR

PAR IEN LIBR

Sem (Ropers )

LEC LEVELLER

3.3_ PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

AN

The machine can easily moved by using their castors. When moving the game machine, always retract the levellers to the extreme up position, so the castors can make contact with the floor. Please ensure that the levellers are raised fully when moving the machine, even for short distances. Furthermore:

© Do not use the handlebar or the rear handle to move the platform (rider assembly), unless the levellers are raised fully.

@ When moving the machine on slopping or uneven surfaces or across steps, proceed with extreme caution to avoid the risk of being crushed!

e If there are steps or step-like differences in grade, move the machine by separating into each unit. Be sure to catch the bottom part.

e During transportation, pay attention so that de castors do not thread power cords.

e Ensure that there is enough room to get through doors or to avoid any collision with elements hanging from the ceiling. Read section 4 to know the dimensions of the machine.

The two units of the machine are not equipped with lifting rings. It is therefore absolutely prohibited to lift them with ropes or belts!

Page 12

3.4__PRECAUTIONS TO BE HEEDED DURING OPERATION

AN

Please heed the following indications in order to ensure the safety of the customers when using this game machine. Be sure to read and get a good understanding of each item:

e Before starting the operation, please check if all the level adjusters are in firm contact with the surface of the ground. If they are not, the cabinet can move and cause an accident.

© Do not use the machine as support for other objects.

© Do not put on the machine or near by any kind of receptacle containing chemicals or water.

e Ensure to provide enough space around the machine to avoid the risk of injury or trouble. Insufficient installation space can cause the player to come in contact with spectators or hit them.

In order to avoid injury and accidents, it is not allowed to use the machine to those persons who fall under the following cases:

e Intoxicated persons.

e Persons susceptible to motion sickness.

e@ Persons who are not in good health, such those having problems of high blood pressure or heart malfunctions.

e@ Pregnant women

@ Persons whose acts do not observe the warning notices.

e Persons whos could be unable to support themselves at both footrests being sitting (disabled people, children, etc.).

Despite the machine is fitted with protection hoods to avoid access to potentially dangerous places, do not allow customers to put hands, fingers or extraneous matter in any opening of the cabinet.

Playing this game with high-heeled shoes is likely to cause a potentially hazardous situation.

Page 13

3.5 SAFETY DEVICES CONCERNING THE MOTION SYSTEM

The ATV-TRACK / MOTION machine has two dedicated devices that provide additional safety to the player when the game is running:

e@ An EMERGENCY STOP BUTTON placed on top of the fuel tank, which can be easily activated by the player or the operator at any time. The game keeps running but the motion stops until the button is unlocked manually by turning it clockwise.

e@ A SAFETY STOP SYSTEM, that stops motion immediately if the player does not press simultaneously both rider footrest. The game still runs but the machine does not move until both footrest are pressed.

The combined action of these two devices reduces the possibility of an accident resulting from sudden sickness or improper use of the machine while it is moving.

Page 14
  • MATERIAL HANDLING

This machine should be transported or moved by trained persons. Failing to do so could result in injury or product damage. Please be very careful.

4.1 TRANSPORT OF PACKAGED UNITS

The packaged machine must be transported in a closed means of transport with sufficient carrying capacity for the gross weight of the machine, which is 205Kg for de monitor cabinet and 240kg for the platform. The machine, must remain packaged on its pallet must be suitably secured to the means of transport. It is very important that the lifting forks are pushed right to the back of the wooden pallet, to give optimum stability to the load.

CODE width depth height crate weight MONITOR CABINET 990 mm _| 1190 mm |_ 1920 mm 205 Kg PLATFORM 990 mm | 1190 mm | 1300 mm 240 Kg

It is not allowed to lift the packed machine with ropes or belts, as the package is not equipped with suitable lifting points for this tape of transport.

4.2__STORAGE

Store the packed machine in sheltered and dry areas. Temperatures allowed: maximum +45°C / minimum -5°C.

4.3 RECEPTION

The ATV-TRACK packaging should be carefully inspected upon receipt to ensure that the product is delivered in good conditions. Shipping damage may void warranty. In case of shipping damage, contact your Distributor and the Transportation Carrier immediately. See section 5.1 for further inspection.

Page 15
  • UNPACKING, ASSEMBLING and INSTALLATION

It is best to unpack the machine where it is going to be used or in a place as near as possible to this. Two people are needed to lift the cardboard packaging over the top of each unit. Once the packaging is removed, the machine looks as shown in the illustration.

5.1_INSPECTION BEFORE ASSEMBLING

Normally, GAELCO products are ready to assemble immediately after transporting to the location. Nevertheless, some mishandling may occur during transportation. Check the following points to ensure that the machine has been properly delivered:

e Examine the cabinet exterior for dents, chips, or broken parts © Verify that castors and levellers are not damaged e Inspect the major assemblies, such as the video display monitor, handlebar and seat. Make sure that they are mounted securely and that all ground wires are firmly connected. Ensure that the power supply voltage and frequency requirements meet those of the location. Ensure that the fuses already installed meet the specified rating and type. Inspect the power cable to ensure that it is not damaged. Verify that the keys delivered with the machine open all doors. Check if all the accessories are included.

Page 16

5.2 ASSEMBLING & INSTALLATION

To assemble the machine proceed as follows:

  • Take out the boxes containing the accessories.
  • Remove the metal brackets that fix each unit to its pallet.
  • Raise the leg levellers and put the units down on the floor with the help of a ramp. Be very careful to avoid the risk of being crushed!
  • Assemble the billboard on the top of the monitor cabinet, using a step. Do not climb on the cabinet!

J The screws that fix the billboard

are already installed on its place. Remove those screw and use them for fixing the billboard. Plug the connector of the fluorescent tube.

  • Assemble the back mudguards and the exhaust pipes. The mudguards are between the chassis and the exhaust pipes, as shown in the drawing. The screws are already installed on the chassis, four on the bottom and one on each side. Take out those screws and use them to fix the assembly. Plug in the the brake light connector.
Page 17
  • Place the monitor cabinet is at its final location and strictly follow the instructions described in section 3.2. Ensure that the cabinet is level, then secure the height of the leg levelers by fastening the adjuster nut upwards.
  • Proceed to assemble the two units together. This must be done where the machine is to be used. First of all make sure the monitor cabinet is level. Then follow the steps below:
  • Remove the metallic covers of the cabinet.
  • Take out the nuts M12. Those nuts are for shipping purposes only. They are useless for assembling.
  • Approach the two units. Pass the cables coming from the platform through the holes of the monitor cabinet, then push the lugs on the platform into the holes in the base of the monitor cabinet.

hw pea

  • Level the platform to the same height as the monitor cabinet. Dp

> =

  • Connect the cables of the motion system. Check that all the connectors are OK. Connectors of the monitor cabinet must fit perfectly with those coming from the platform.
  • Tighten the two bolts M12 that fasten the platform to the monitor cabinet. The corresponding nuts are welded to the base of the platform.
  • Replace the covers of the monitor cabinet.
  • If the machine has to be moved, even just a little bit, retract the leg levellers first.
  • Carefully adjust all the levellers so that the whole machine rests firm and level on the floor. (See section 3.2). Remember that the platform contains a motion system!

To clean the game machine, wipe with a soft cloth damped with a neutral detergent and wrung out. Using organic solvents like thinner may damage the plastic parts.

Page 18

5.3__GETTING READY TO START

BEFORE SWITCHING ON THE MACHINE, PLEASE CHECK THAT THE INTALLATION FITS ALL THE REQUIREMENTS DESCRIBED ON CHAPTER 3 (SAFETY NOTES) AND ESPECIALLY THOSE OF SECTION 3.2

The installation of the machine at its final site should be carried out by trained people. Mains power must be always be turned off, and the machine unplugged, before replacing any part or handling connectors. Please check the following points again:

e The area chosen for the machine is well away from heat sources. @ The machine does not obstruct emergency exits. @ The whole machine is level and stable on the floor. The leg levellers are secured in place. e The power cord can be plugged into a grounded receptacle that provides the specified voltage and frequency. e@ The mains supply is equipped with an Earth Leakage Breaker rated at 30mA.

5.4__SWITCHING ON THE MACHINE

The mains switch is located in the compact filter assembly, which also contains the fuse and the socket for the mains cable. It is found in the back of the monitor cabinet.

To start the machine, push the switch to position

The machine can be switched OFF (position "0") whenever necessary. If a game is in progress on the machine, the credit will be lost.

To avoid possible damage to the electronic components, wait several seconds before turning the machine on again.

Page 19
  • PROGRAMMING THE MACHINE AND TEST MODE

An automatic check of the memories is made when the machine is switched on. This coincides with the presentation of the Screen Test. After a few seconds, if no error occurs, it automatically goes on to show the game. The interface is also adjusted dynamically each time that a machine is switched on. Any other adjustment should be made in TEST MODE.

The access to the TEST MODE as for the other controls -monitor, sound, etc.- is made from the CONTROL PANEL, which is situated behind the coin box door. This panel consists of a button to access TEST MODE, a coin counter, a SERVICE button, and a commuter to adjust the VOLUME of the loudspeakers.

ATV-416

Pressing the TEST button enters TEST MODE, where the game variables, such as level of difficulty, linkage of machines, etc., can be adjusted. A check of the motion system and other controls can also be made. The SERVICE button allows the technician to introduce game credits without moving the coin counter.

The main menu of TEST MODE offers seven options:

SCREEN TEST INPUT/OUTPUT MOTION SYSTEM SETTING SOUND BOOK-KEEPING EXPORT PROGRAM EXIT

You can choose the option required by handling the brake levers. Pushing the START button placed on the handlebar makes the selection.

To make sure that the changes that have been made are kept permanently, you must not switch off the machine without first leaving TEST MODE with the option exit and save settings of the EXIT screen.

Page 20

6.1 SCREEN TEST

This screen is the ADJUSTMENT CARD, which should be used to suitably adjust the monitor. It shows you, also, information about the installed software version.

gaelcois

You can return to de Main Menu by pushing the TEST button (placed on the control panel) or the START button (placed on the handlebar).

6.2_INPUT/OUTPUT TEST

The INPUT/OUTPUT screen enables you to check the correct functioning of the following controls:

Start Button Emergency Stop (see warning) Coin Chute Service Button Test Button Volume Down Volume UP Left Brake Lever Right Brake Lever Throttle

Handlebar Position

Steering Motor Placed on the throttle assembly (handlebar) Placed on top of the fuel tank Coin Acceptor Placed on the Control Panel Placed on the Control Panel Placed on the Control Panel Placed on the Control Panel Rear brake Front brake The number on the left goes from 0.00 (no acceleration) to 1.00 (maximum acceleration) The number on the left goes from -1.00 (top left position) to 1.00 (top right) Feedback force. The number of the left goes from 1.00 (handlebar on top left position) to -1.00 (top right)

The control signal is selected by means of the brake levers. The status of each signal changes when the related control device is activated.

Page 21

The INPUT/OUTPUT screen looks like this:

TEST MODE (INPUT / OUTPUT)

Start Button OFF Emergency Stop ON (ver nota) Coin Chute OFF Service Button OFF Test Button OFF Volume Down OFF Volume UP OFF Left Brake Lever OFF Right Brake Lever OFF Throttle 0.00 (014) Handlebar Position 0.10 (126) Steering Motor -0.10

Push Start Button to return to Main Menu

Warning! When checking the EMERGENCY STOP, remember that the message displayed on the screen is ON when the button is released. So, if the message is “OFF”, it means that the button is working (motion system disabled). Once pushed, the button will remain mechanically locked until you turn the red knob clockwise.

When you want to return to the main menu, just push the START button.

Page 22

6.3__MOTION SYSTEM TEST

This screen enables you to check some functions related to the motion system.

TEST MODE (MOTION SYSTEM)

Mode: SOFT

Left Motor: 0.00 ( 0.75) Right Motor: 0.00 (-0.98)

Motion Test

Return To Main Menu

Press Any Brake Lever To Choose/Simulate And Push Start Button to Enter/Contirm

Mode There are three working modes of the motion system:

e DISABLED The motion system does not work. e SOFT The motion is quite soft during the initial phases of the game, then comes harder. e HARD The motion is hard from the beginning of the game.

Left Motor / Right Motor This is an option for maintenance purposes that allows a manual control of each motor, using the brake levers (right lever to move up, left to move down). The left number shows the speed while the number between the brackets shows the position.

Motion Test The system moves following a repetitive pattern, allowing you to see if there is anything wrong with it.

Return to Main Menu You leave the screen by choosing this option and then pushing the START button.

Page 23

6.4 SETTINGS

You can change the following game parameters on this screen:

TEST MODE (SETTINGS)

Country: (146) SPAIN 1 Coin 1 Credit 1 Credit to Start Difficulty: NORMAL Advertising Sound: YES Continue: NO Link Mode: NOT LINKED

Return To Main Menu

Press Any Brake Lever To Choose And Push Start Button to Enter/Contirm

The parameter is selected with the brake levers, then changed by pushing the START button.

Country This option allows you to change the idiom of some messages addressed to the player.

Coin / Credit On this option you can adjust the number of credits (games) that the machine gives for a defined number of coins. If the number of coins is set at zero, the machine remains adjusted for FREE PLAY.

Credit to start Here you can program the number of coins required to start the game.

Difficulty The game has four levels of difficulty: EASY, NORMAL, HARD and HARDEST.

Advertising sound By means of this option you can program the machine for sound production (or mute) when it is in display mode.

Continue When this option is enabled, the player can start a game from the last stage passed on the previous game.

Link This line shows the status of the machine. If it is linked with another machine you have to assign a different status to each one of them. One should be MASTER and the other

Page 24

SLAVE as indicated on the options (MASTER-RIGHT CABINET / SLAVE-LEFT CABINET). If there is any interconnection problem, the following messages can appear on the screen:

LINK ERROR: master/slave duplicated This message means that both machines are configured with the same status, either master or slave, so they do not communicate properly.

LINK ERROR: data receive error There is an obvious problem of communication.

LINK ERROR: bad checksum in program This message use to appear when the machines do not have the same program version. If so, you have to go to the option EXPORT PROGRAM of the Main Menu. (section 6.7)

If there is no link between two machines the option NOT LINKED should be selected.

To leave this screen push the START button after selecting the option “Return To Main Menu’.

Page 25

6.5 SOUND TEST

This screen allows you to check the whole sound system.

TEST MODE (SOUND TEST)

Left Loudspeaker Right Loudspeaker Subwoofer (Bass) Music 000 Stopped Sound 000 Stopped Sample 000 Stopped

VOLUME - IIIIIII + BALANCE - | + BASS —- IIIIII1 +

Time : 00:00:00

Return To Main Menu Press Any Brake Lever To Choose And Push Start Button To Enter/Contirm

To leave this screen push the START button after selecting the option “Return To Main Menu’.

Page 26

6.6 BOOK-KEEPING

The data for the activity of the machine are collected on three screens. To go from one screen to another is necessary to press any of the brake levers. The first screen shows the following information:

TEST MODE (BOOK-KEEPING)

Total Credits 0082 Coin Credits 0008 Service Credits 0002 Number Of Games 0069 1P. Practice Games 0004 1P. Competition Games 0065 2 Players Games 0000 Number Of Continues 0000

Grip Any Brake Lever To Change Push Start To Return To Main Menu

Reading from top to bottom:

Total number of credits

Credits owed for the coins entered

Credits entered with the SERVICE button

Total number of games

Number of games of an individual player, in PRACTICE mode

Number o games of an individual player, in COMPETITION mode

Number of games of two simultaneous players (Link Mode)

Number of games using the Continue option

To go onto the next screen, press any of the brake levers. To return to the Main Menu push the START button.

Page 27

The second screen shows the following information:

TEST MODE (BOOK-KEEPING)

Total Time (hh:mm) 03:40 Play Time (hh:mm) 188:55 Longest Game (mm:ss) 15:24 Shortest Game (mm:ss) 00:46 Average Game (mm:ss) 02:43 Longest Distance (Km) 01204 Shortest Distance (Km) 00005 Average Distance (Km) 00544

Press Any Brake Lever To Change Push Start To Return to Main Menu

Reading from top to bottom:

e Total time the machine is connected in hours, minutes and seconds

© Total time the machine is busy in hours, minutes and seconds

e Time of the longest credit in minutes and seconds

© Time of the shortest credit in minutes and seconds

e Time of the average credit in minutes and seconds

e Longest distance covered in a game (best player)

e Shortest distance covered in a game (worst player)

e Average distance covered in a game (average player)

To go onto the next screen press any of the brake levers. To return to the Main Menu push the START button.

Page 28

The third screen shows additional information about the game events at each stage. It also includes the number of players who passed all stages (Winners) and those eliminated for spending all the time available (Time out).

TEST MODE (BOOK-KEEPING)

Level Game Over

1.1 0007 1.2 0072 1.3 0131 21 0000 2.2 0005 2.3 0004 3.1 0001 3.2 0002 3.3 0009 41 0001 42 0002 4.3 0008 Winners 0002 Time Out 0035

Grip Any Brake To Change Push Start To Return to Main Menu

To return to the Main Menu push the START button.

Page 29

6.7_ TRANSFER OF THE PROGRAM VERSION

The option EXPORT PROGRAM should be used when two machines are linked and their program versions are different. In such a case, the updated version must be loaded on the PCB that has the older version. The data transfer is done from the machine with the updated program, following the instructions shown on the screen:

RECORDING PROCESS

  • Switch off the other machine
  • Switch on again with the Service button pressed

Press Start Button to record

Press any brake lever to ABORT the process

The recording process starts when the Start button is pressed, and it lasts about 5 minutes. If anything goes wrong, an error message will appear on the screen. When the process ends successfully, press any of the brake levers to return to the Main Menu

Page 30

6.8 EXIT Screen

On this screen the following options are displayed:

TEST MODE (EXIT)

Exit Without Saving Changes

Exit And Save Changes

Reset Hall of Fame

Reset Book-Keeping

Return To Main Menu

Grip Any Brake Lever To Choose And Push Start Button To Confirm

Reading from top to bottom:

e Exit from Test Mode without keeping the changes

e Exit from Test Mode retaining memory of the changes that have been made in the previous screens

e Erase data of the game record tables that accumulate from day to day.

e Erase the book keeping data.

e Return to Main Menu

Selection is made with the brake levers, while the option chosen is switched in with the START button.

Reset of record tables and book-keeping data is made directly by pushing the START button.

Warning! Whatever the changes that have been selected in the previous screens (SETTINGS & MOTION SYSTEM) will be eliminated unless you exit from this final screen using the option exit and save changes, confirmed with the START as indicated on the bottom of the screen.
Page 31
  • HOW TO PLAY

ATV-TRACK is an arcade game that challenges the player’s ability to control a QUAD trough a course plenty of natural obstacles, by using a handlebar with throttle and two brake levers. The goal of the player is to complete in succession the four phases of the game.

Starting the game

To start to play it is necessary to put enough coins to cover the price of at least one credit. The number of coins introduced is shown together with the number of coins necessary to obtain one credit. For example, if the programmed number of coins per credit is two, the displayed message will be, step by step: “Credits 0 / 2”, “Credits 1 / 2” and “Credits 1”. The cost of a credit is programmed from Test Mode (see section 6.4, SETTINGS).

When the necessary coins have been put in, the message “INSERT COIN” changes to “PUSH START BUTTON”. By pushing this button the player can choose the game options.

Game options

The first option offered to the player is to choose the game mode, which can be COMPETITION or PRACTICE.

In COMPETITION mode, the player can choose to be a boy (ZAKK) or a girl (JILL) in the virtual world of the game. Four models of QUAD are also available. The main rule for this mode is to pass the four phases in succession, beginning on phase1.

In PRACTICE mode, the player can choose to start riding from any of the first three phases of the game. Once this selection is made, it is possible to choose boy or girl but not a QUAD, which is predetermined.

Turning the handlebar makes the selection of the different options. The player confirms the selection by pushing the START button or by a quick turn of the throttle grip.

Game rules

On COMPETITION mode, the player receives a card at the beginning of each phase. The card has 15 blank squares (5 squares per stage, 3 stages per phase). Each square will be filled with an “OK” if the player passes the corresponding stage. If not, the stamp will be “X”. The rules of the game are simple: there are 5 checkpoints along one stage and the player has a fixed time to pass each checkpoint. If the player arrives on time, the corresponding square is filled with the “OK” stamp. If the player spends the available time before reaching the checkpoint, there is a penalty (“X” stamp). If the card is filled with three “X”, the player is eliminated. A new card is delivered when the player succeeds and goes onto the next phase.

There is a counter with a fixed amount of time. If the player does not reach a checkpoint on time, the seconds consumed are deducted on the counter until the available time is zero. This generates the “Time out” elimination. The player wins when the four phases of the game are completed. The prize then is a nice show with fireworks.

Page 32

On PRACTICE mode, the card is not filled with “X” so the player is not disqualified by accumulation of “X” but only for wasting time (Time out). The squares are filled with information about the dexterity of the player: “OK” means that he is doing well, “REG” means that he is doing so-so, and “BAD” means that he could perform much better. When the game is over, there is a global qualification that indicates if the player can try on COMPETITION mode or it is wiser to practice a little more.

Helping icons

There are two icons that appear along the course when the player is doing well. Those icons give special advantage to make extra jumps (JUMP) or to run faster during a short span of time (TURBO)

Scores

The score is represented by kilometers. A longer distance corresponds to a better player. To encourage the competition, there are some “hidden kilometers” that are added to the actual distance covered by the player. Those bonuses are always in the same place but not along the obvious path of the course, so the players have to search them and memorize the locations. There are two types of record list: the “Top 20” parade, which keeps the absolute distances covered by the 20 best players, and a daily list with the longest distance covered on each stage. Those partial records of the daily list are erased when the machine is switched off at the end of the day.

7.1__COMPETITION ON LINK MODE

When two players compete directly, using two linked machines, the game rules are a bit different:

e The game starts and ends in a single phase only, to be selected by the players. e The smarter player will take more "OK" on his card, while the other will accumulate "X". e The game ends when the available time is consumed (TIME OUT). The program decides who wins and each player can reed the appropriate message, either "YOU WIN" or "YOU LOOSE".

Page 33
  • HOW TO LINK TWO MACHINES

ATV TRACK allows you to connect two machines so that two players can compete directly. To do this the following steps should be taken:

. Make sure that the connection cable is correctly plugged into both machines. . Switch on both machines. . Press the TEST button on the CONTROL PANEL of both machines. . Go to the SETTINGS on both machines (See section 6.4 of this manual) . Go to Link options and define the condition of each machine, Master or Slave as indicated on the screen. . Go to the EXIT / CONTINUE screen, choose EXIT AND SAVE CHANGES option and validate with the START button. ARWN=

fon)

If there is any problem, due to configuration error, bad communication or different program version, an error message will appear on the screen.

When you want to disconnect the two machines, you should unplug the link cable and proceed in the same way from step 2. On step 5 choose NOT LINKED for both machines, then exit from de Test Mode with the option EXIT AND SAVE CHANGES of the EXIT screen.

Warning! If the machines have different program version, please follow the proceeding described on Section 6.7.
Page 34
  • TECHNICAL SERVICE

9.1 PRIOR CONSIDERATIONS

Technical service and maintenance must be carried out by qualified staff.

No modifications shall be made to the machine unless these have been approved by the manufacturer in writing. Failure to observe this requirement may cause damage or accidents and will automatically render the guarantee null and void.

If any task needs to be performed which is not described in this manual, please contact the distributor for instructions. The manufacturer declines any liability for damage and injury arising from failure to comply with this requirement

aN

e@ Before commencing work on the machine, maintenance staff must read this manual carefully and check that all of the safety norms concerning the installation and use of the ATV-TRACK. Maintenance staff must advise the operator of any irregularities they observe so that the latter can take the appropriate measures to put matters right. 9.2 SAFETY PRECAUTIONS

@ The machine must be disconnected from the power supply before beginning any kind of maintenance work (changing parts, repairs, etc.), except where this is confined to a simple check on whether the machine is working properly. Hold the plug when unplugging the machine - DO NOT PULL ON THE CABLE !

e Parts of the power supply unit (PSU) and the monitor remain hot or store high voltage even when the machine has been unplugged. Do not touch these parts as electric shock or burns may result.

e@ Make sure there is plenty of room for maintenance to be carried out. At least 3 metres should be left free between the machine itself and other objects (e.g. adjacent machines, walls, etc.).

@ When parts needs replacing, use only those approved by Gaelco S.A. and which meet the relevant specifications.

Page 35

9.3 BRAKE LIGHT

When the brake light needs replacing, remove the plastic cover as shown in the diagram. Unplug the connectors before pulling.

Bulb: 24V/5W

9.4 HANDLEBAR MECHANISM

Access the handlebar mechanism by removing the screws which hold the two plastic covering pieces. To remove the mechanism, remove the screws which hold it to the ATV chassis, ensuring the two cables are disconnected before lifting out the assembly.

Page 36

9.4.1 ADJUSTING THE CHAIN TENSION

Adjust the chain tension as follows:

  • Loosen the screws holding the tensing roller shafts (as shown in the drawing). Half a turn is enough.
  • Then, adjust the chain tension by tightening the side screws. To check whether the chain is properly tensed: the nylon rollers should press tightly enough against the chain to be difficult to turn by hand but still sufficiently loose to be able to turn despite the friction. Bear in mind that when the top screws are tightened, the rollers will close and press even more tightly against the chain. This may make the handlebar too hard to turn.
Page 37

Checking the rollers

  • Tighten the top screws and re-check the pressure of the rollers against the chain. If they cannot be turned by hand, they are pressing too hard against the chain. If this is the case, repeat the process again, this time loosening the side screws a little. Once again, tighten the top screws and check the pressure by turning the rollers by hand. Repeat the process as many times as is required until the criteria set out in Step 2 are met.
Page 38

9.4.2 CHANGING THE BRAKE CABLES

To change the brake cable, proceed as follows:

  • To work more easily, disassemble the handlebar following the procedure described in the first paragraph of this chapter (page 37)
  • Remove the protective rubber covers from the brake levers.
  • Pull on the cable sleeve and remove the brake lever cable, as shown in the diagrams on this page.
Page 39
  • Remove the screw which holds the plastic cupola to the steering assembly shaft. Then lift the cupola, as shown in the diagram. This reveals the support area to which the cables are held.
  • Open the special clamp holding the cables
Page 40
  • Loosen the nuts which hold the damaged brake cable with the help of the two 12mm spans, releasing the cable lever which operates the micro-switch.
  • The cables can then be lifted out of their plastic cupola by pulling them upwards.
  • Fit the new cable by following the reverse procedure, beginning by threading the cable into the cupola from the top. Adjust the largest diameter cable holder in the cupola and then follow the steps below:

e Fit the end of the cable in the lever housing. e Fit the tensor. Fit the other end of the cable to the brake lever. Bear in mind that the cables from the cupola cross over to the opposite handlebar. Close the special clamp over the cable, whilst holding the cable holder. Fit the cupola. Adjust the tensor. Fit the control in the chassis, remembering to connect the cables. Adjust the sleeve so that it does not rub against either the screws on the bearing box or against the screws which hold the control assembly onto the chassis. Fit the rubber sleeves back on the levers. Fit the plastic covers back on steering assembly. e Ensure that both the brakes and the steering assembly are working properly by checking the INPUT / OUTPUT screen in Test Mode.

9.4.3 CHANGING THE BRAKE MICRO-SWITCH

If the micro-switch needs changing, ensure that the cables are connected to the square terminal and that it is a contact which is NORMALLY CLOSED (NC). This terminal is the one closest to the square terminal.

Page 41

9.5 EMERGENCY AND SAFETY STOPS

The movement system includes two stop devices - an emergency one and a safety one. The emergency stop is operated by a red knob on top of the fuel tank. The safety stop operates when the player ceases pressing on either of the bike foot rests. The emergency and safety circuit-breakers are connected in series so that either of them will bring the bike to a standstill. The last section of Chapter 3 provides details concerning their use. Should the movement system not work, the cause may lie in: either of the stop switches ; in the cables ; or on the CPU board. The following steps must be taken before finding the fault:

  • Remove the metal covers which cover the base of the monitor, as shown in the diagram.
  • Remove the Faraday cages which cover each of the motor drivers. This reveals the LED screens which provide information on the state of each driver.
Page 42

9.5.1 EMERGENCY STOP CIRCUIT

To check the emergency stop circuit, check the CPU IN /OUT screen in Test Mode and SELECT THE LINE "Emergency Stop": _ if the red knob is in the rest position (circuit closed, movement possible), the message will read ON. When the red knob is pressed, the message will change to OFF (circuit open, motors stopped). When the knob is turned clockwise, the movement system is ready to operate. The message turns back to ON (movement system ready).

However: the previous check only covers the signal processed by the CPU but the problem could lie in a circuit which goes directly to the drivers. To check whether this is the case, select the Movement Test from the MOVEMENT SYSTEM screen while in Test Mode. Refer to the circuit diagram in following the steps below:

Display

RD +24)

~ |

a £

=i|—
—_—g=14
UL_)re21
.353
Displayauyo=

xz *} a

| RD | 2

  • * “ a

E Emergency stop

When the Movement Test option is selected, the optocoupler breaks the circuits of the footrest micro-switches (see right-hand side of illustration). Under normal conditions, when the button is in the rest position (i.e. not pressed), the message " rd " will appear in the left-hand window of both drivers. However, if the message is "ih", this indicates that the circuit remains open for some reason (e.g. bad connection, damaged cable, faulty button, etc.). The stop message will appear on the monitor screen, consisting of an image of the stop knob and an acoustic warning.

Page 43

The most likely fault is a short-circuit if the message of the drivers is neither " rd" nor" ih "and there is no stop message on the monitor.

9.5.2 SAFETY STOP CIRCUIT

Para verificar el estado de este circuito se entra en la pantalla ENTRADAS / SALIDAS To check the safety stop circuit, go to the CPU IN /OUT screen in Test Mode and keep the emergency button in the rest position (ON). When pressure is released from either of the drivers, the message on both controls should be " ih ". If this is not so, the technician can deduce the problem by following the circuit diagram.

To change a switch, the top part of the corresponding footrest needs to be taken off by removing the screw marked "2 "on the diagram. Item 1 is the nut which secures the switch bracket.

*To see the footrest in detail, please refer to section 10.20 of this Manual.

Page 44

9.6 POSITION OF THE BRAKE LEVERS AND THE THROTTLE

The brake levers must be assemble so that they abut the curve of the handlebar and are positioned as far as possible from the ends of the handlebar. The right hand brake lever provides the reference point. The brake bracket aligns with a hole through which the potentiometer, accelerator, and start button cables go. As will be seen in the line drawing, the moulding line on the bracket lines up with the longitudinal centre of the hole.

a

/ ALICNFMENT

The left-hand brake lever is assembled in the same plane as the right-hand lever. The throttle is assembled so that the union between the two covers lines up with the moulding line of the lever bracket, as shown in the line drawing.

The separation between the mechanism housing and the brake lever bracket (*) is some 4-5mm. The inside of the throttle lever must not rub against the end of the tube - if it does it will not turn freely. The left grip is separated from the lever body by some 35mm.

Page 45

9.7 DISASSEMBLING AND ASSEMBLING THE THROTTLE

Follow the procedure below when disassembling the throttle (e.g. when checking the potentiometer, etc.):

  • The first step is to loosen the grub screw on the top cover (see line drawing). There is a seating for the grub screw in the handlebar tube. The seating stops the whole assembly turning when force is used to work the throttle.
  • Remove the two screws holding the covers to the tube. The lower cover comes away easily whereas the upper cover tends to remain stuck to the throttle recovery mechanism. To remove the top throttle cover, turn the throttle anti-clockwise while holding the cover with the other hand. When the cover is freed from the throttle, it will hang from the start button cable.
Page 46
  • To replace the covers and the throttle, simply follow the reverse procedure: first, attach the bracket in the seating for the upper cover (see illustration), then tighten up the screws which hold both covers in place (the assembly can still be turned at this juncture), finally find the position (see Section 9.6) in which the grub screw seats back into the tube.

To check the assembly is steady, grab the two covers and try turning the assembly first one way and then the other. If the control has been properly assembled, it will not turn.

9.8 ADJUSTING THE ACCELERATION POTENTIOMETER

In assembling the throttle, it is very important to observe the following point: The first tooth of the pinion wheel (as shown in the line drawing) must fit the first indent to the right of the tooth aligned with the grub screw holding the pinion wheel. The grub screw presses against the flat part of the potentiometer shaft. This determines the exact alignment between the two items.

NOTE: The right-hand illustration gives an imaginary view of the alignment point mentioned above (indicated with an arrow). In reality, the rubber throttle cover prevents one from seeing the assembly.
Page 47

To check the potentiometer, check the Accelerator option from the INPUT /OUTPUT screen and check the values are as follows:

  • Throttle (right forward)

Reading 00(006) The figure in brackets may vary between 001 and 006.

  • Full Throttle (maximum acceleration)

Reading 01(230) The figure in brackets may vary between 220 and 230.

If the readings are outside these values in the respective throttle positions, it indicates that the potentiometer pinion is wrongly positioned with respect to the throttle.

9.9 PARTIAL DISASSEMBLY OF THE PROTECTION HOOD

Proceed as follows when accessing areas protected by the hood:

  • Enter the MOVEMENT SYSTEM screen in Test Mode, with the brake levers in their highest position on the mobile platform (corresponding to figure 0.50 for both motors). For further details, consult Section 6.3 of this manual. The relevant figure is shown on the right in brackets.
  • Remove the four screws which hold the top of the hood to the mobile platform. The line drawing only shows the screws on one side.
Page 48
  • Push the hood upward (i.e. towards the upper part of the column). This frees a metal catch located beneath the mobile platform, allowing the hood to be folded down flat.

9.10 CHECKING POSITION POTENTIOMETERS

If the movement system is not working properly, the position potentiometer (ATV-305) should be checked and changed if necessary. The following points need to be borne in mind in this connection:

  • When the shaft lever is completely upright (as shown in the illustration), the woodruff key will also be in the upright position. Read the brake position on the MOVEMENT SYSTEM screen while in Test Mode. When the position is reached, check that the line marked on the silicon tube lines up with the motor woodruff key. The mark on the silicon tube lines up with the woodruff key on the motor shaft. The mark lines up with the centre of the flat part of the potentiometer shaft.
Page 49
  • Viewing the motors from above, when the shafts are in the position indicated, check that the left shaft woodruff key is lined up with the black line on the silicon tube and that the right shaft woodruff key is lined up with the red line on the tube. To see which motor is left and which is right, look at them from the direction shown by the arrow at the bottom centre of the illustration.

Left Right

9.11 ASYNCHRONOUS MOTORS - CIRCUIT DIAGRAM

The motors operating the movement system are three phase ones. In the ATV-TRACK application, they are connected in triangular fashion (see diagram).

L1, L2 and L3 are cables from the Commander SE frequency converters.

Page 50

9.12 CHECKING THE COMMANDER SE PARAMETERS

Frequency concverter model: COMMANDER SE

Starting position: Machine connected, movement system off.

The two digit screen shows the parameter number. The three digit screen shows the parameter programming.

Begin check:

  • Press button M on the speed control.
  • Press the arrows to select the parameter.
  • Check the parameter value matches the one shown on the list below:
Nr.ValueNr.Value
10.023SP
250241.00
30.5250}
40.526ON
5A1.PR270
64.3028NO
7150029NO
8230301
90.85311
10L232OFF
110.0330
120.034ON
130.0352
140.036Fr
151.5376
164-.20380
17OFF3950.0
18=40Auto
19=41AnSi
20=4248
21=431.1
22A44-

If the programming is wrong, contact the manufacturer.

The error codes can be checked by consulting the short manual for the speed controls, supplied with the machine.

Page 51

9.13: TROUBLESHOOTING PROCEDURES

  • PROBLEM:The machine does not start when the mains switch is thrown.

CHECKS @ Check the mains cable and its connections. @ Check the fuses. Check the specifications are met. Check whether the fuses have blown and that they have the correct current rating. The fault may have been caused by an overload current. @ Check the CPU connections © Check there is +5V AC in the power supply.

  • PROBLEM:There is something wrong with the screen colours and/or image.

CHECKS e Enter in Test Mode and adjust the monitor settings with the help of the screen test (see Section 6.1)

  • PROBLEM:The game starts but the platform fails to move.

CHECKS © Check that the rider is pressing down correctly on both footrests. Check the emergency stop button is not pressed. @ Check the movement system by looking at the corresponding screen whilst in Test Mode (see Section 6.3): if the platform moves, the problem lies in one of the footrests. In this case, apply the procedure described in Section 9.5.2. If the game platform still fails to move, carry out the following checks: © Check that the connections between the monitor casing and the game platform are not loose and that the cables are undamaged. © Check that the frequency converters work properly (i.e. no error message (see Sections 9.5.1 and 9.12)). @ Check the DC driver (ATV-358): If the fuses have blown, it is likely that the power transistors have short-circuited.

  • PROBLEM:The game platform moves but not in synchronism with the ATV image on the monitor.

CHECKS e Enter the MOTION SYSTEM screen in Test Mode and check that the platform is at its highest point when taking the reading position of both motors. The reading should be 0.50. If this is not the case or the platform leans to one side, check the position potentiometer following the procedure described in Section 9.10. © Check that the screws (ATV-829) are properly tightened on their respective shafts. © Check that the plastic coupling (ATV-819) is not twisted and that it does not slip on the sleeve which stands proud of the head of the centring screw (ATV-829).

Page 52
  • PROBLEM:The game platform moves very slowly the whole time.

CHECKS @ Check the potentiometers are working properly and that none of the cables have broken.

  • PROBLEM: The throttle does not work.

CHECKS e Enter the INPUT/OUTPUT screen in Test Mode. Check that the throttle meets the conditions set out in Section 9.8. e lf the reading does not change on twisting the throttle grip, check the state of the cable from the throttle to the connector housed in the steering assembly. Lift the handlebar cupola, following steps 1,2,3 and 4 described in Section 9.4.2 and check potentiometer circuit continuity by measuring the electrical resistance between the connector pins at the point where three cables meet. e lf there are any discontinuous or false readings, open the throttle control following the procedure described in Section 9.7 and check there are no broken cables. e If all the cables running to the potentiometer are in good condition, check the potentiometer resistance by measuring the electrical resistance on the terminals. © Follow the instructions in Sections 9.8 and 9.7 to reassemble the throttle.

  • PROBLEM:The START button does not work

CHECKS e Follow the same procedure as in case 6, checking first the current continuity on the connector pins housed in the steering assembly (location at the point where two cables meet). e If the circuit is faulty, open the throttle control assembly following the procedure described in Section 9.7. © Follow the instructions in Sections 9.8 and 9.7 to reassemble the throttle.

  • PROBLEM:The ATV accelerates in a jerky manner and may even brake when it should go faster.

CHECKS @ Open the throttle, following the procedure described in Section 9.7. © Check that the throttle travel stop (limiting top speed) is not broken. Do this by holding the potentiometer bracket and twisting the throttle, forcing it a little at the end of its travel. e Check the linkage between the potentiometer wheel and the throttle meet the conditions set out in Section 9.8. © Follow the instructions in Sections 9.8 and 9.7 to reassemble the throttle.

Page 53
  • PROBLEM:The machines do not work when they are linked up.

CHECKS © Check that the link cable properly connects the two machines. e Follow the instructions in Section 8. The error message descriptions are set out in Section 6.4 (Link Mode).

  • PROBLEM: There is no sound or it is of poor quality.

CHECKS © Change the volume on the Control Panel. © Carry out a sound test (see Section 6.5) © Check the connections.

  • PROBLEM: The fluorescent tube fails to light

CHECKS ®@ Check the fluorescent tube by removing the mounting plate (ATV-517). To do this, remove the four screws (ATV-959) show in the illustration in Section 10.5. Use a step ladder or other firm support when doing so. For safety reasons, it is strictly forbidden to clamber over the monitor casing.

NOTES

Page 54

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 55

GAELCO - ATV TRACK- MOTION

  • PARTS LIST

10.1 MONITOR CABINET — MONITOR, SUBWOOFER & ACCESSORIES

CODE DESCRIPTION

ATV-350 ATV-362 MONITOR Polo/2, 34”, STAR PH — CODE 02197790, SVGA cable 600mm 8” SUBWOOFER 100W/4Q. ATV-363 FAN 220V 120X120X38 ATV-365 FAN GRILL ATV-375 8” GRILL, subwoofer ATV-434 PLASTIC HANDLE C36055007 ATV-903 WASHER DIN125 M8, monitor ATV-922 SCREW DIN603 M8X45, monitor ATV-950 SCREW DIN7505-B 4X14, plastic handle & subwoofer ATV-971 NUT DIN934 M8, monitor ATV-981 NUT DIN985 M8, monitor

ATV-903 ATV-971 ATV-903

AIV-363 ATV-365

ATV=434 ATV-951

Page 56

GAELCO - ATV TRACK- MOTION

10.2 MONITOR CABINET - COIN DOOR & SPEAKERS

CODE DESCRIPTION

ATV-232 BRACKET, Test & Service Panel ATV-281 ATV-282 COIN ACCEPTOR RAIL — Type 1 COIN ACCEPTOR RAIL — Type 2 ATV-299 TEST & SERVICE PANEL ATV-360 5” SHIELDED LOUDSPEAKER, 60W / 4Q / 2VIAS — CODE 35.1368 ATV-411 MINI DOOR, 1 ENTRY — CODE P1001707520S2000 ATV-925 SCREW DIN 7985, M4X10, zinc plated ATV-934 SCREW DIN 912, M6X40 ATV-950 SCREW DIN 7505-B, 4X13

Page 57

GAELCO - ATV TRACK- MOTION

10.3 MONITOR CABINET — SERVICE PANEL & CASH BOX

CODE DESCRIPTION ATV-395 | VOLUME SWITCH ATV-396_| TEST/SERVICE PUSH BUTTON ATV-399 | COUNTER, 6VDC. ATV-412_| MINIBLANK DOOR COB — CODE P10000073000000 ATV-416 | PLASTIC CASH BOX - STANDARD ATV-950 | SCREW DIN 7505-B 4X13

Page 58

GAELCO - ATV TRACK- MOTION

10.4 MONITOR CABINET — PLASTICS AND ACCESSORIES

CODE DESCRIPTION

ATV-105 | MONITOR REAR DOOR ATV-235_| SAFETY SWITCH BRACKET ATV-366_| SAFETY SWITCH ATV-367_| VENTILATION GRILL ATV-435_| DOOR LOCK, REF. AGA 135 ATV-510_| FRONT PLASTIC. ATV-515 | BILLBOARD ASSEMBLY

ATIV-366.

Page 59

GAELCO - ATV TRACK- MOTION

10.5 MONITOR CABINET —- BILLBOARD ASSEMBLY (ATV-515

CODE DESCRIPTION

ATV-516_| BILLBOARD ATV-517_| FLUORESCENT ASSEMBLY ATV-950 | SCREW DIN 7505-B 4X10 ATV-962 | SCREW UM1001 M6X20

10.6 MONITOR CABINET — BASE COVERS

CODE DESCRIPTION

ATV-220 | METALLIC COVER — RIGHT ATV-221_| METALLIC COVER — LEFT ATV-366_| SAFETY SWITCH 701BIP ATV-501 ATV-962 SCREW UM1001 M6X20, black

ATV-962

ATV=366

ATV=221

ATV=962_

Page 60

GAELCO - ATV TRACK- MOTION

10.7 MONITOR CABINET — BASE PARTS

CODE DESCRIPTION ATV-222 | UNION BRACKET ATV-363_| FAN 220VAC, 120X120X38 ATV-364_| MAINS SWITCH & FUSE HOLDER (2X10A) — CODE 2752RS ATV-367_| VENTILATION GRILL 15X15 ATV-377 | SLEEVE @16X@12X32, rubber spacer ATV-378 | RUBBER SPACER, T-SHAPE, @40X@28X15 — hole 916 ATV-379 | RUBBER STOPPER @50X45 / M10X25 ATV-412_| MINI BLANK DOOR COB — CODE P10000073000000 ATV-416 | PLASTIC CASH BOX - STANDARD ATV-431_| LEG LEVELLER M16x102 with rubber pad ATV-433_| SWIVELING CASTOR @80 ATV-902_| WASHER DIN125 M6, leg levellers ATV-903_| WASHER DIN125 M8, union bracket ATV-911_| WASHER DIN9021 M12, cabinet to platform fastening ATV-922 | SCREW DIN603 M8X45, castors and union bracket ATV-939 | SCREW DIN603 M6X70, leg levellers ATV-948 | SCREW DIN933, M12X45, cabinet to platform fastening ATV-950_| SCREW DIN 7505-B, 4X13 ATV-980_| NUT DIN985 M6, leg levellers ATV-981 | NUT DIN985 M8, castors

Page 61

GAELCO - ATV TRACK- MOTION

ijl AIV-939 ; AIV=431 i a ng ; ATV=902 tft ATV-980 ‘3 ¢ 1

ATV-922 ATV=433 ATV-903

ATV-981

Page 62

GAELCO - ATV TRACK- MOTION

10.8 MONITOR CABINET —- CONTROL PARTS

CODE DESCRIPTION

ATV-110 WOODEN TRY ATV-225 ATV-231 FARADAY BOX (AC. DRIVER) SUPPORTING PLATE, toroidal transformer ATV-355 PSU — SB180PL/R, monitor ATV-357 CPU — ATV TRACK ATV-358 DC DRIVER, steering motor ATV-370 TOROIDAL TRANSFORMER 220V/18-0-18/160VA/4,44A-CROVISA 218316 ATV-371 AUTOTRANSFORMER 117V/220V/1500VA (optional for USA) ATV-372 INDUCTANCE, 10 mH, 6A ATV-373 EMI SHIELDING FERRITE - SLEEVE CORE, 26x28x13 (MOTOR) ATV-374 CYLINDRICAL EMI SUPPRESION CORE (SIGNAL) ATV-385 DERIVATION TERMINAL BLOCK BM 9982 - GND ATV-386 DERIVATION TERMINAL BLOCCK BM997 — POWER SUPPLY ATV-389 ATV-390 FIXING RAIL for derivation terminal blocks SERIAL FILTER 800 / 6A - CODE 806G ATV-392 AC DRIVER SE11200075, induction motor ATV-902 WASHER DIN 125, M6 ATV-944 SCREW DIN 912, M6X70

ATV—358.

ATV—231

AIV-225

ATV=374 t Yr Wt (SIGNAL) de ANV=373 ay (MOTOR) Py

ATV=371 (USA)

ATV=225

Page 63

GAELCO - ATV TRACK- MOTION

10.9 PLATFORM — MAIN ASSEMBLIES

ASSEMBLY 1

ASSEMBLY 2

ASSEMBLY _3

Page 64

GAELCO - ATV TRACK- MOTION

10.10 ASSEMBLY 1 — DESIGN RELATED PARTS

CODE DESCRIPTION

ATV-803 BACK MUDGUARDS ATV-805 ATV-806 LEFT SIDE COVER RIGHT SIDE COVER ATV-807 SEAT RUBBER — FRONT ATV-808 SEAT RUBBER — REAR ATV-812 STICKER — LEFT, head of the rotomoulded chassis ATV-813 STICKER — RIGHT, head of the rotomoulded chassis ATV-814 FRONT MUDGUARDS ATV-815 REAR ASSEMBLY, including exhaust pipes and handle ATV-832 SPACER SLEEVE ATV-833 SQUARE WASHER ATV-883 STICKER, back mudguards (instructions) ATV-885 BRAKE LIGHT ATV-924 ATV-927 SCREW DIN7985 M4xX20 SCREW DIN912 M8X16 ATV-938 SCREW DIN912 M10X40 ATV-956 SCREW UM1001 M8X12 ATV-957 SCREW UM1001 M5xX10, zinc plated ATV-979 NUT DIN985 M4 ATV-983 NUT DIN985 M10

Page 65

GAELCO - ATV TRACK- MOTION

Page 66

GAELCO - ATV TRACK- MOTION

10.11 ASSEMBLY 1 —- PARTS ON TOP

CODE DESCRIPTION

ATV-300 STEERING ASSEMBLY ATV-801 ATV-802A ROTOMOULDED CHASSIS, orange FUEL TANK COVER — FRONT ATV-802B FUEL TANK COVER — REAR ATV-807 SEAT RUBBER — FRONT ATV-808 SEAT RUBBER — REAR ATV-817 EMERGENCY STOP BUTTON ATV-845 STOPPER BRACKET, emergency button ATV-932 SCREW DIN912 M8& ATV-913 SPRING WASHER DIN197 M8& ATV-957 SCREW UM1001 M5X10

ATV- 957 = LUG ATV- 957 ye

ATV- 802-A

Page 67

GAELCO - ATV TRACK- MOTION

10.12 ASSEMBLY 2 (STEERING ASSEMBLY ATV-300)

CODE DESCRIPTION

ATV-301_| HANDLEBAR ASSEMBLY ATV-303_| STEERING MECHANISM

ATV-301

ATV-300 He ~ ATV-303

ATV-300 = ATV-301 + ATV-303 ASSEMBLED TOGETHER

Page 68

GAELCO - ATV TRACK- MOTION

10.13 HANDLEBAR ASSEMBLY (ATV-301)

CODE DESCRIPTION

ATV-306_| HANDLEBAR BRACKET —A ATV-307_| HANDLEBAR BRACKET - B ATV-308 | SCREW DIN912 M5X20 ATV-309 | PLASTIC CLAMP ATV-310_| HANDLEBAR ATV-311_| RUBBER GRIP @22 ATV-312 | BRAKE LEVER — LEFT 20012009 ATV-313 | BRAKE LEVER — RIGHT 20012008 ATV-314 | BRAKE CABLE ATV-317_| CLAMP @22X50 M6 ATV-318 | NUT DIN394 M6 ATV-319 | WASHER DIN127 M6 ATV-320_| THROTTLE ASSEMBLY ATV-804 | PLASTIC CUPOLA ATV-957 | SCREW UM1001 M5X10 plastic cupola

ATV— 314 ATV- 957 ATV- 311 ATV— 312

ATV— 804

ATV-_320

ATV=

ATV-319

Page 69

OLg—-ALY T @Z£—-ALV SIE-ALV V7E-ALV 19 1E-ALV eZE-ALV SIf-ALV SLXSW ZLENIG MANOS |_9E-ALV yewez ‘YV3A9 YSLSWOILNALOd |_SZe-ALV pbLle 70'S LYOddNS YALAWOILNALOd | 7Ze-ALV UYAAOO dOL |_€Ze-ALV E212 2O'S~LL YAAOD WOLLOG| 2ZE-ALV l0Z2°2O'6SZL dIND FILLOMHL| 1Ze-ALV uoyng ysnd “LAN | LOLe-ALY aged UM ‘MIA / LYWLS — NOLLNG HSNd | 9Le-ALV LAN YSLAWOILNSLOd |_LSLE-ALV OOTEVS — YALAWOILNALOd OWS | SLE-ALV UYVEATONVH | OLE-ALV NOILdId9Sa4qd E[«foye) (0ze-ALV) ATEWASSV STLLOMHL Pl OL NOILOW -MOVUL ALY - OO14V9

Page 70

10.15 STEERING MECHANISM - BLOCK A

MANUF. CODE DESCRIPTION

  • C-11-404311 SPRING CK-67 13] S-GA-QU014001] SPRING HOLDER @6X17 17| S-GA-QU012001] LEVER SOPPER @8X17 18] S-GA-QU013001] LEVER SHAFT @12 (@8X17) 19] S-GA-QU015002| LEVER AP-02 (55X20X6)
  • C-22-03018 FLAT WASHER DIN125 @8mm, zinc plated
  • C-22-04017 CIRCLIP DIN6799 @7mm
  • C-22-0501406 | GRUB SCREW DIN913 M4x6
  • C-40-401510 POTENTIOMETER PINION, CuZN37 (@15.75X11.4)
  • C-43-050300 BUSH @14X10, self oil 25] S-GA-QU000301} POTENTIOMETER BRACKET AP-02, zinc plated 26] C-22-03014 FLAT WASHER DIN125 @4mm, zinc plated 27| C-22-03064 SPRING WASHER DIN7980 @4mm (Glower type) | 28] C-22-0105410__ | SCREW DIN7985 M4X10, zinc plated
  • C-22-028038 POTENTIOMETER NUT, 3-8 30} C-22-030038 POTENTIOMETER WASHER, 3-8 31} C-29-405680 POTENTIOMETER ASSEMBLY 64] C-22-01031060_| SCREW DIN933 M10X60, hexagonal 65] C-GA-QU02010 | POLYAMIDE STOPPER 67| C-22-0112410 | SCREW DIN912 M4X10, Allen 68] C-22-011238 SCREW DIN912 M3X8, Allen 69] C-22-03013 FLAT WASHER DIN125 @3mm, zinc plated
  • C-10-1401010 | SPACER @6X2.5, CuZn37
  • C-09-11231 MICROSWITCH C-09-11231 73} C-22-0104320 | SCREW DIN84, zinc plated (C-22-014320)
Page 71

—~ — o-—

Page 72

GAELCO - ATV TRACK- MOTION

10.16 STEERING MECHANISM - BLOCK B

MANUF. CODE DESCRIPTION 12} C-22-9950510 _| SCREW M5xX10 (to be riveted)

33] C-22-03036 WASHER DIN9021 M6, zinc plated | 32] C-22-0103660__| SCREW DIN933 M6X60, hexagonal, zinc plated

34] S-40-0250301 BELT FASTENER PLATE AP-02 35} S40013202301_| DRIVE PULLEY @31.2X30.5, steering motor 36] S-GA-QU000201| MOUNTING BRACKET, steering motor 37} C-22-03015 FLAT WASHER DIN125 @5mm, zinc plated 38} C-22-03085 SPRING WASHER DIN6798/A @5mm 39] C-22-02015 NUT DIN934 M6, zinc plated 40} C-22-03084 SPRING WASHER DIN6798/A @4mm

  • C-29-401582/1_| STEERING MOTOR — UJAQUE CC-1582/1 42} C-40-085027 STEERING DRIVE BELT HTD-400-5M-15
Page 73

GAELCO - ATV TRACK- MOTION

10.17 STEERING MECHANISM — BLOCK C

MANUF. CODE DESCRIPTION

1} C-22-020212 LOCKNUT DIN985 M12, zinc plated |_ 2] C-22-030812 SPRING WASHER DIN6798/A @12mm 3] C-22-030112 FLAT WASHER DIN125 @12, zinc plated 4} C-GA-QU010100} SHAFT 194.5X10X15X0.15X125.8mm 5| C-22-800255518 | WOODRUFF KEY DIN6885 6| C-22-020110 NUT DIN934 M10 7| C-22-030810 SPRING WASHER SIN6798/A @10mm 8] C-22-030110 FLAT WASHER DIN125 @10mm, zinc plated 9} C-40-000300 BEARING HOUSING, zamak 50] C-22-03601522_| WASHER DIN988PS (15X21X1) 51] C-40-206002 BEARING 6002-ZZ (@32X9) 60} C-40-022197 PLASTIC PINION M-0.75 Z80 61| C-GA-QU04020 | DRIVE GEAR, metallic (@111X20.1) [62] S-40-042010T | DISC @45X10mm 63} C-40-000A302 | STEERING STOPPER, zamak 66} C-22-01031030 | SCREW DIN933 M10X30, hexagonal

Page 74

GAELCO - ATV TRACK- MOTION

10.18 STEERING MECHANISM — BLOCK D

MANUF. CODE DESCRIPTION

10} C-22-0112620 SCREW DIN912 M6X20, Allen | 14] C-22-0112820 SCREW DIN912 M8xX20, Allen 15} C-22-03068 SPRING WASHER DIN7980 @8mm (Glower type) 43} C-GA-QU040450] SPECIAL BOLT, tempered 44] C-GA-QU010200] SHAFT 93X10.5X89.5 45} C-22-80025512_| WOODRUFF KEY DIN6885 (5X5X12) 46] C-GA-QU04010 | DRIVE CHAIN 47| C-GA-QU04047 | PLASTIC PULLEY Z-64 (@100.7X18) 48] S-GA-QU052001| SPACER SLEEVE @15.5X25X10, zinc plated 49] C-GA-QU04030 | DRIVE PINION, metallic (@43x13.8) 50] C-22-03601522_| WASHER DIN988PS (@15X21X1) 51] C-40-206002 BEARING 6002-ZZ (@32X9) 52| C-22-040110 _ | SPACER SLEEVE, bearings (016 (@20X29.75)) | 53] C-40-000310 BEARING HOUSING (SPECIAL), zamak 54] C-22-040110 CIRCLIP DIN6799 210mm 55| C-GA-QU02030 | POLYAMIDE ROLLER, chain fastener 56] C-GA-QU01030_| SHAFT @20X54.2) 57| C-GA-QU02020 | ALUMINIUM BLOCK, chain fastener 58| C-22-03066 SPRING WASHER DIN7980 016 (Glower type) 59} C-22-0112640 SCREW DIN912 M6X40, Allen

Page 75

GAELCO - ATV TRACK- MOTION

10.19 ASSEMBLY 3 - MOBILE PLATFORM

CODE DESCRIPTION

ATV-810 PROTECTION FOLDING HOOD — MOBILE PLATFORM ATV-811 ATV-8111 PROTECTION HOOD ASSEMBLY — UNIVERSAL JOINT PROTECTION HOOD ATV-8113 HOSE CLAMP W2 @140-160 ATV-8114 NYLON FASTENER 500mm ATV-825 SWIVEL JOINT, maleM14+maleM14, MJ14M-STS ATV-834 FOOTREST BASE (MOBILE PLATFORM) ATV-835 BORDER TUBE — LEFT ATV-836 BORDER TUBE — RIGHT ATV-846 LEFT BRACKET, protection folding hood ATV-847 RIGHT BRACKET, protection folding hood ATV-849 PASSENGER FOOTREST ATV-850 RIDER FOOTREST (see exploding 10.22) ATV-917 ATV-918 WASHER DIN6798 A 6,2 WASHER DIN6798 A 8,2 ATV-942 SCREW DIN933 M12X30 ATV-957 SCREW UM1001 M5xX10, zinc plated ATV-959 SCREW UM1001 M6X10, black ATV-980 NUT DIN985 M6 ATV-981 NUT DIN985 M8& ATV-982 NUT DIN985 M12 ATV-996 RIVET @5X10

DRAWING ON NEXT PAGE

Page 76

GAELCO - ATV TRACK- MOTION

ATV-850

ATV-942

ATV-835

ATV-825

ATV-836 / ATV-957,

ATV-959

ATV-846

ATV- 8113

ATV- 8111

ATV- 8114

ATV-982 Phd

Page 77

GAELCO - ATV TRACK- MOTION

10.20 RIDER FOOTREST ASSEMBLY

CODE DESCRIPTION

ATV-851_| RIDER FOOTREST - UPPER PLATE, aluminium ATV-852_| RIDER FOOTREST - BOTTOM PLATE, iron ATV-853_ | BRACKET, rider footrest microswitch ATV-854 | SPRING, rider footrest ATV-855 _| MICROSWITCH ATV-855T | NUT, microswitch ATV-872 | MICROSWITCH CABLE, rider footrest ATV-928 _| SCREW DIN912 M6x12, zinc plated ATV-980_| NUT DIN985 M6 (rider footrest - internal)

ATV-851

ATV-980 —= — ——

¢ ATV-854 ATV-: 4 855T

Q ATV-853 > ATV-855

ATV-872

ATV-852

es ATV-928

Page 78

GAELCO - ATV TRACK- MOTION

10.21 ASSEMBLY 4 - MAIN STRUCTURE

CODE DESCRIPTION

ATV-809 STICKER, rear cover ATV-830 ATV-839 MAIN STRUCTURE CARDAN ASSEMBLY (universal joint + column + fixing plates) ATV-841 FRONT STRUCTURE COVER ATV-842 MOTOR COVER — RIGHT ATV-843 MOTOR COVER — LEFT ATV-844 MOTOR COVER — REAR ATV-861 LEG LEVELLER, @60 M16, with rubber pad ATV-862 CASTOR @80 ATV-863 SWIVELING CASTOR @80 ATV-881 STICKER-LEFT ATV-882 STICKER-RIGHT ATV-903 WASHER DIN125 M8& ATV-915 ATV-918 WASHER DIN127 M12 WASHER DIN 6798 A 8,2 ATV-935 SCREW DIN912 M12X20 ATV-943 SCREW DIN933 M8X20 ATV-959 SCREW UM1001 M6X10, black ATV-981 NUT DIN985 M8&

Page 79

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 80

GAELCO - ATV TRACK- MOTION

10.22 MOTION MECHANISM

CODE DESCRIPTION

ATV-305 5KQ POTENTIOMETER — GAELCO ATV-819 ATV-820 ELASTIC COUPLING, silicone tube @5 GEARED MOTOR MB2301-S1-BO00C-40-TU-LSMV80L — RIGHT ASSY. ATV-821 GEARED MOTOR MB2301-S1-B00C-40-TU-LSMV80L — LEFT ASSY. ATV-825 SWIVEL JOINT, male M14 + male M14, 1702-MJ14M-STS ATV-826 HEXAGONAL ROD, motor transmission ATV-827 SHAFT CRANK, motor transmission ATV-829 CENTERING SCREW, elastic coupling ATV-848 POTENTIOMETER BRACKET ATV-904 WASHER DIN125 M10 ATV-910 WASHER DIN9021 M10 ATV-914 SPRING WASHER DIN127 M10 ATV-936 SCREW DIN912 M8xX10 ATV-947 ATV-949 SCREW DIN933 M10X70 SCREW DIN933 M10X20 ATV-972 NUT DIN934 M10 ATV-976 LOCKNUT DIN936 M14, thread 2

Page 81

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 82

POWER WIRING DIAGRA

POWER

SUPPLY

| aware} [peaae

MONITOR

BOARD

LAMP aTv-517 11.1 POWER WIRING 11. WIRING DIAGRAMS

Page 83

FARADAY BOX

STIRRUP-L ©

STIRRUP-R ©

STOP LAMP ©

GROUND WIRING DIAGRAM

T¥2366 af:

FREQUENCY

INVERTER SL

POWER

SUPPLY CPU BOARD aty-357

atv-392

INVERTERSR atv-392 FILTER Atv-390 Laie eww wii’ FLUORESCENT ee LAMP o FAN Atv-363, ELP-03 ELR-03 ranenonao COIN DOOR ADAPTER COIN 11.2 GROUND WIRING

Page 84

11.3 CABINET WIRING - SECTION A

PLATFORM WIRING DIAGRAM

ver oRWe—

ADEE

Page 85

11.3 CABINET WIRING - SECTION B

CABINET WIRING DIAGRAM

POWER [2

SUPPLY

: g zi & Boars = . ny Sot

Page 86

11.4 MECHANICAL AND ELECTRONIC COIN ACCEPTORS

MECHANICAL COIN ACCEPTOR

6.3Vv ELP-06

ELECTRONIC COIN ACCEPTOR i ' i i i) 1 i

:RED-8!

' \

'COIN LAMP6.3V:
1BLK-B|

\ ! E A ELP-06 '

'a CcA+12vec2 [7 i
17 CDCNBE— 2 f

Re 3 '

iN DpA[___ COUNTER TH—4 = 1
1aP2 i

c —d

'TT
9=!
1RRI

i) i 1 Ves ee Se ee es ee ee pe ee ATV-338 1

Page 87
  • CREDIT DISTRIBUTOR SETUP

JP1:Not used JP2:Cabinet JP3:Coin controller JP4:Not used

JP3 Connector JP2: This connector should be connected to ATV PCB wiring

JP2 Description Values Source/Destination

Pin 1Input GNDGNDGND power supply
Pin 2 _| Input VDC+12 VDCDC power supply
Pin 3__|Counter output0/+5/+12 VDCCoin counter
Pin4Credits output+5/0 VDCCredits for CPU

Connector JP3: Input connector of electronic coin controller. Setup per channel.

PIN Signal Active

1ovov
2+12VDC+12VDC
3Output 5ov.
4Output 6Ov

5 ary

6LockHigh
7Output 1Ov.
8Output 2ov.
9Output 3Ov
10Output 4Ov

9 7 5 3 1 10 | 8 6 | 4 2

(As seen from components side)

Page 88

PROGRAMMING OF COIN CONTROLLERS

Controllers supported: COIN CONTROL C-120 NRI G-13.6000 MARS CASHFLOW 330

IMARS 330/S 212OPAOPBOPCOPDOPEOPF

INRI G-13.6000 Channel| Channel| Channel| Channel} Channel} Channel

123456

(Coin Control C 120 Coin 1 | Coin2 | Coin3 | Coin4 | Coin5 | Coin6

IPIN Controller:7891034
USA==iadss1$50 Ct25 Ct
Great Britain==1£50 Pen==20 Pen |_ 10 Pen
Australia====5$==2$1$
Switzerland==5 Fr2FS1FS
Sweden=s10 Kr5 Kr==1Kr
INorway20 Kr10 Kr5 Kr====1 Kr
IEURO€2€1€50cse20c10c

SWITCH SETUP FOR EUROS

SW1: Always OFF SW2: Always OFF SW3: Not used

SW4-SW5: Extra Credits (Bonuses) Combinations of this two dip switches are used to program bonuses (free games) according to the scale shown in the table. The table varies according to the game price selected.

SW6-SW7-SW8: Game Price These dip switches are used to choose the game price. The bonus table shows the combination of game prices with the payments that allow the player to obtain extra games (bonuses).

(*) Add another credit for the second lap.

CREDITS table BONUS table (SW4/SW5)

SW6 | SW7 | SW8|_Value/CreditOFF/OFFON/OFFOFF/ONON/ON
OFF | OFF | OFF10cNo bonus50c40c20c
ON | OFF | OFF20cNo bonus50c40c20c
OFF | ON | OFF30cNo bonus*50c30c60c
ON | ON | OFF40cNo bonus2€1,6€80c
OFF | OFF | ON50cNo bonus2,5€2€1€
ON | OFF | ON80cNo bonus2€1,6€80c
OFF | ON | ON1€No bonus2,5€2€1€
ON | ON | ON1,2€No bonus2€1,6€2,4€
Page 89

APPLICATION EXAMPLES

Game price: 50c, NO BONUS Switch set up:

swi Sw2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 OFF | OFF | OFF | OFF | OFF | OFF | OFF | ON

Game price: 50c, BONUS FOR 2€ (4 credits + 1 credit free) Switch setup:

swi Sw2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 OFF | OFF | OFF | OFF | ON | OFF | OFF | ON

Game price: 1€, NO BONUS Switch setup:

swi sw2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 OFF | OFF | OFF | OFF | OFF | OFF | ON | ON

Game price: 1€ , BONUS FOR 2,5€ (2 credits + 1 credit free) Switch setup:

swi sSw2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 OFF | OFF | OFF | ON | OFF | OFF | OFF | ON

Page 90

SWITCH SETUP FOR OTHERS CURRENCIES

SW1: Always OFF

SW2: Coin multiplication factor

SW2=OFFChanel:123456
Euro 8, and rest of EuropeValue:X20}X10]X5 | X4 | X21]X1
SW2=ONChanel:123456
(USA)Value:X20 | X10}X8 | X4 | X2]X1

SW3: Not used

SW4-SW5: Extra Credits (Bonuses) Combinations of these two dip switches are used to program bonuses (free games) according to the scale shown in the table. The table varies according to the game price selected.

SW6-SW7-SW8: Game Price These dip switches are used to choose the game price. The bonus table shows the combination of game prices with the payments that allow the player to obtain extra games (bonuses).

(*) Adds another credit for the second lap.

CREDITS table BONUS table (SW4/SW5)

SW6 | SW7 | SW8|Value/Credit | OFF/OFF | ON/OFFOFF/ONON/ON
OFF | OFF | OFF10542
ON_|_OFF | OFF20542
OFF|_ON | OFF30*536
ON | ON | OFF4020168
OFF | OFF | ON50252010
ON | OFF | ON8020168
OFF | ON | ON100252010
ON | ON | ON120201624
Page 91

APPLICATION EXAMPLES

Example 1

SwitzerlandSW1 =|_OFF_|SERIAL input. (5 FS via PIN 5) = (Channel 3)

SW2 =| OFF _| Input values x1 x2 — x5 SW3 = Not used

SW4 =|OFF|EXTRA credit on the 20th pulse (=20FF)

SW5 =| ON

1 FF = 1 pulseSW6 =|OFF |5 pulses / 1 credit.

SW7 =| OFF SW8 =| ON RESULTS: 5 FS /1 credit; 20 FS / 5 credits

Example 2

SwedenSW1 =|_OFF_|SERIAL input. (5 Kr via PIN 5) = (Channel 3)

SW2=|_OFF | Input values x1 x2 — x5 SW3 = Not used

SW4 =|OFF|EXTRA credit on the 20th pulse (=20FF)

SW5 =| ON

1 Kr = 1 pulseSW6 =|OFF |5 pulses /1 credit.

SW7 =| OFF SW8 =| ON RESULTS: 5 Kr /1 credit; 20 Kr / 5 credits

Example 3

NorwaySW1 =|_OFF_|SERIAL input. (5 Kr via PIN 5) = (Channel 3)

SW2 =| OFF _| Input values x1 x2 — x5 SW3 = Not used

SW4 =]ON|EXTRA credit on the 25th pulse (=20Kr)

SW5 = |_ OFF

1 Kr = 1 pulseSW6 =|OFF|10 pulses / 1 credit.

SW7 =| ON SW8 =| ON RESULTS: 10 Kr /1 credit; 25 Kr / 3 credits

Example 4

Great BritainSW1 =|OFF _| SERIAL input. (10 Pen via PIN 8) = (Channel 6)

SW2 =| OFF _| Input values x1 x2 — x5 SW3 = Not used

SW4 =]ON|EXTRA credits on the 5th pulse (=50 Pen)
SW5 =|OFF_|and 10th pulse (1 £)
1 Pen = 1 pulseSW6 =|OFF |3 pulses / 1 credit.

SW7 =| ON SW8 =| OFF RESULTS: 30 Pen /1 credit; 50 Pen / 2 credits; 1 £ / 5 credits

Page 92

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.