Rad Mobile Deluxe Type 1st Printing MR (420-5876-01)
Rad Mobile (World) (Sega, 1990) · Manual · 100 pages · 15 sections · original scan
1ST PRINTING-MR aK Ro Rod Rd Rd Ko Ko Ko Ko ho Ho Ko Ho Ko Ko Ho Ko Ko Ko Ho Ko Ko Mo Ho Ho Ho HK HH
MODI.
OWNER’S MANUAL
DELUXE TYPE
SEGA ENTERPRISES, LTD. :
: EAPO PGP GP GP GP PIP GP GP IP GP EP QP GP EP gPgE BELL LLL LL EELPLEEE LEP PEPE PPPS
P YP BP GP AP GP BP IP YP BP BP BP OP MANUAL NO. 420-5976-01
TABLE OF CONES —————————
INTRODUCTION OF THE OWNER'S MANUAL HANDLING PRECAUTIONS
PREVENTION OF COUNTERFEITING AND D CONVERSION a
PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION NAME OF PARTS . ergrenaane ae REMOVING THE COIN CHUTE TOWER woscecescce sas ene nee eee DISASSEMBLING THE CABINET =
AC UNIT - REMOVING THE MECHANISM UNIT | AND ) MOTOR
- ADJUSTMENT OF ASSY MECHANISM'S LIMIT SWITCHES i
- ADJUSTMENT OF THE V BELT AND REPLACING THE MOTOR BRUSH-- CONHSM PRONE
- HANDLE V.R. ADJUTMENT - - 17
- REMOVING & ADJUSTING THE ACCELERATOR/BRAKE. UNIT ~- 18~19
- REPLACING THE START/LIGHT/WIPER BUTTONS - sees 20
- BEAM SENSOR ADJUSTMENT —.-.------ sve 21~ 22
16. MONITER CLEANING AND FLUORESCENT L LAMP P REPLACEMENT - - 23
- 26 INCH MONITOR -------------- coonnennnenmnre 24
- PERIODICAL INSPECTION ------------------------- - ee 2) 19, TEST MODE - - 26~42
- COIN/CREDIT § SETTING - 43
- ROM LOCATIONS 44
- IC BOARD ORGANIZE - 45
23. VOLTAGE CHANGES TO LOCAL REQUIREMENTS 46
24, PARTS LIST 47~95
- WIRING DIAGRAM 96~97
——— SPECIFICATIONS + INSTALLATION SPACE ; 1800mm(70. 9in)(D) x 1300mm(51. 2in) (W) + HEIGHT : 1650mm(65. 0in) + POWER : 310W °C.R.T. : 26 INCH + WEIGHT : 350Kg (771. Obs. )
INTRODUCTION OF THE OWNER'S MANUAL
SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, ete. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER'S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanicals servicing control, Spare parts, etc. as regards the RAD MOBILE a new SEGA product. The manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstance touch the interior system.
- HANDLING PRECAUTIONS
When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely.
© Be sure to turn the power off before working on the machine. To insert or pull out the plug quickly is dangerous oO It is necessary to make sure that the power cord or the grounding wire iS not exposed on the road, etc. in a manner so as to be dangerous. Make sure that grounding connections are made safely fe)
at the position where so specified. © Do not use any fuse that does not meet the specified rating. © Make complete connections for the IC board and other connecters. Insufficient insertion is very dangerous
Also, for the IC board circuit inspections, only the logic tone is allowed. The use of a teSter is not permitted, so be careful in this regard. After confirming that there are no irregularities turn the power ON
- PREVENTION OF COUNTERFEITING AND CONVERSION
LABELLING
To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or by converting, selling or using such products or printed circuit boards
ORIGINAL SEAL LICENSE SEAL
The following seal is put on The following seal is put on the the machines manufactured by kits, such as the printed circuit SEGA. boards, of SEGA products
td t t ' t t ' 2FStGm ENTERPRISES. ETO arr a eat
COPYRIGHT NOTICE
This SEGA product has the copyright notice as follows
© SEGA 1990
This signifies that this work was disclosed in 1991 and is the property of SEGA ENTERPRISES, LTD.
PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION
The RAD MOBILE DX is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage :
Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower Places subject to direct sunlight. Places subject to heat sources from heating units, etc., or hot air Vicinity of highly inflammable/volatile chemicals or hazardous matter.
Sloped surfaces. Vicinity of anti-disaster facilities such us fire exits and fire extinguishers. Places subject to any type of violent impact Dusty places.
INSTALLATION OF THE RAD MOBILE DELUXE TYPE
© Use an independent outlet for the power supply. (The bresker may break when the maximum current is consumed if the outlet is simultaneously used for the power source of other machines. )
© When using an extension cord, use one with a Specified rating or higher.
AC120V AC220V AC240V
RATED CURRENT T.5A 4.9A 5.1A
For installation, make doubly sure that attention be paid to the above points.
- NAME OF PARTS
26 INCH MONITOR
(200-5112-15)
HANDLE MECHANISM
(RDM-2000) ACBL UNIT
(RDN-1200)
. 4q COCKPIT COIN CHUTE TOWER ; : “an ioon
(RDM-0500)
BASE
(RDN-3000)
STEP BOX ~ (RDM-0550) BEAM SENSOR
(RDM-3010)
MOTOR
(¥2-3203)
POWER AMPLIFIER ‘TRANSFORMER : MOTOR DRIVER (601-6227-01) (680-5148) . (400-5117Y)
TOOLS & ACCESSORIES
| PART No | Q/U DESCRIPTION 509-5298 1 | PUSH BTN SW IT YELLOW W/LAMP 220-5130 1 | VOL CONT B-5KOHM RDM-2006 1 | EXT SPRING | 540-0006-01 1 | WRENCH FOR TAMP PRF SCR DUAL TYPE M4 540-0008-01 1 | WRENCH FOR TAMP PRF SCR DUAL TYPE M8 509-5372 PUSH BUTTON SWITCH IT GREEN W/LAMP
509-5373 PUSH BUTTON SWITCH IT BLUE W/LAMP RDM-1212 TORSION SPRING R
RDM-1213 TORSION SPRING L
- REMOVING THE COIN CHUTE TOWER
BASE COVER LEFT
RDM-3005
HEX NUT MLO
ASSY TOWER & STEP
RDM-0500
@ Remove the ASSY BASE side BASE COVER LEFT (RDM-3005) and take off the four Mi0 HEX NUTs. Pull the ASSY TOWER & STEP towards
you, disconnect the 5 CONNECTORs and remove the COIN CHUTE TOWER
from the ASSY BASE.
- DISASSEMBLING THE CABINET
The CABINET which is the machine's main part, can be disassembled into 3 parts, i.e., the MONITOR, COCKPIT and ASSY BASE.
MONITOR
COCKPIT [
BASE ASSY
%* SEPARATING THE MONITOR
@ Remove the DASHBOARD PLATE by taking off the four M4~x 10 TAMPERPROOF SCREWs and disconnect the 4 CONNECTORs in total
which are connected to the monitor.
@ Remove the MONITOR COVER FRONT by taking off the five M4x 16 TAMPERPROOF SCREWs.
@ Take off the four M8 BOLTs which secure the front and both sides.
DASHBOARD PLATE
M4x16 TAMPBRPROOF
Lf SCREWs (5)
M8 BOLT
M8 BOLTs
- SEPARATING THE COCKPIT
@ Remove the BASE COVER FRONT by taking off the four M5x10 TAMPERPROOF SCREMs.
| Disconnect the CONNECTORS to remove the BASE COVER from the | BASE.
@ Disconnect the 5 wire CONNECTORS Which hang down to the ASSY BASE from the COCKPIT.
@ Take off the four M12 NUTs which secure the BEARING.
@ Remove the four TAMPERPROOF SCREWS which secure the CON ROD COVER and lower the COVER.
M12 NUT
(4 for front and back in total)
Disconnect the joint portion of the BANK FRAME & CRANK by taking off the M12 NUT and ROD SCREW
At this time, the ASSY COCKPIT tends to lose balance, therefore, be sure to have the work performed by 2 or more persons so that one of them will be able to maintain the
COCKPIT's balance.
Lift the COCKPIT upward to separate it from the ASSY BASE.
ROD SCREW
M12 NUT
Mebile
- SW UNIT
©® COIN CHUTE TOWER
COIN SW 41
COIN SW #2
COIN METER
DEMAGNETIZING SWITCH ..----
SERVICE SWITCH -----------------------
TEST SWITCH
VOLUME ADJUSTMENT
SUPERWOOFER VOLUME ADJUSTMENT @DEMAGNETIZING SWITCH
@SERVICE SWITCH
@TEST SWITCH
@SUPERWOOFER VOLUME ADJUSTMENT
- Used for removing the on-screen color uneveness
Used for the purpose of servicing and increasing the credits without registering on the meter (this allows you to check the
game).
- For the operation of this switch, see SELF-TEST.
Adjusts FRONT SPEAKER volume. Adjusts SUPERWOOFER VOLUME located under the seat.
- AC UNIT
MAIN SW FUSE HOLDER
fie
POWER CORD BARTH TERMINAL
- REMOVING THE MECHANISM UNIT AND MOTOR
@ TAKE OFF BASE COVER FRONT (5 TAMPER PROOF SCREW M4) @ TAKE OFF HOLE BANDAGE (2 TAMPERPROOF SCREW M4)
BASE COVER FRONT
(RDM-3003)
HOLE BANDAGE
@ By inserting a ratchet wrench in the gap between the BASE and MOTOR BRACKET, loosen the M10 BOLTs which fasten the MOTOR
BRACKET, incline the BRACKET to the MECHANISM side, and the V
BELT (350-5198) can be removed from the PULLEY. Also, by taking off the M10 NUTs, the MOTOR UNIT can be removed.
MOTOR UNIT
(YZ-3203) 2 HEX NUT
MECHANISM UNIT
(GLC-3050)
(350-5198)
@ Take off the HEXAGON NUT (M8) which fastens the ROD END to the MOVING PLATE (GLC-3052)
MLO NUT
aa MOVING PLATE ROD END COLLAR amin (GLC-3052) (GLC 3021) FTC] ROD END
3 NUT M8 HL cIZ fl
DETAILS OF PART A
NUT MLO
® Finally, take off the 4 (M10) NUTS which fasten the MECHANISM UNIT and disconnect the CONNECTOR to remove the MECHANISM UNIT.
- ADJUSTMENT OF ASSY MECHANISM'S LIMIT SWITCHES
| When carrying out this work, first be sure to turn the power OFF. |
%* Manually turn the MECHANISM'S PULLEY to move the MOVING PLATE (GLC-3052) (when the PULLEY turns, the COCKPIT will bank).
When the MOVING PLATE moves and the LIMIT SW is actuated by the ACTUATOR (a click sound will be heard), make adjustments ina manner so that there will be a 9~12 mm clearance in between the MOVING PLATE and RUBBER STOPPER
Be sure to carry out the abovementioned adjustments for both right & left LIMIT SWITCHes.
RUBBER STOPPER MOVING PLATE RUBBER STOPPER (601-5472) | (GLC-3052) (601-5472)
- ADJUSTMENT OF THE V BELT AND REPLACING THE MOTOR BRUSH
Power for this machine is transmitted by the V belt. The belt, if it slips or is torn, will not work properly and also is very dangerous. Regularly check as to the tension, wear, and deterioration of the belt and make the necessary adjustments and replacements ahead of time.
ADJUSTMENT OF BELT TENTION
- Before making adjustments of the belt tension, be sure that the power in OFF. For belt tension adjustments, make sure that the belt has an approximate slack of 10 mm when applying a forefinger against the middle part in between the 2 pulleys.
e Loosen the 2 HEX NUTS which Mee MOTOR
fasten the MOTOR BRACKET, adjust the BRACKET'S fixed position and make adjustment of the BELT.
HEX NUT M10
Replace the motor brush as shown below Normally, replacement once in six months is recommended. Make sure that both the 2 brushes are replaced @ To remove the cap, turn it by using a driver, etc. @ Take the brush out for replacement.
MOTOR —_ © Replace the brush when it wears out up to this line.
CAP Ieee] — mami} J a 0 | BRUSH eS) Pepe BRUSH
- HANDLE V.R. ADJUTMENT
+ Perform the V.R. adjustments in the INPUT TEST MODE. When adjusting the HANDLE V.R., loosen the four TAMPERPROOF SCREWS and remove the BONNET PLATE (RDM-1007)
SCRBWs A
SCREWs B
@ Loosen SCREWS A which secure the VOLUME BRACKET and move the VOLUME BRACKET.
@ Move the VOLUME BRACKET to disengage the VOLUME GEAR and HANDLE GEAR. At this time, turn the VOLUME shaft in a manner so as to make sure that the on-screen value is within the allowable range
(80H= 4H).
@ Fasten SCREWs A and at this time, make backlash adjustments.
@ When fine adjustments are needed, loosen SCREWS B, turn the HANDLE GEAR and make fine adjustments.
- REMOVING & ADJUSTING THE ACCELERATOR/BRAKE UNIT
Remove the ACCELERATOR/BRAKE UNIT from the COCKPIT by taking off
the four M8 NUTs from the underside of the COCKPIT.
COOKPIT FLOOR
RDM- 1001
4 TAMPERPROOP. SCREWs (M4)
eS gS
4 HBX NUT M8
ACCELERATOR/BRAKE VOLUME ADJUSTMENT
Display the INPUT TEST MODE (see P.34) screen.
When the variable valve is not within the allowable range, make
adjustments by using the following procedure:
- Loosen the SCREWs “A" used for adjustment
- Turn the GEAR which is attached to the ACCELERATOR/BRAKE VOLUME and make variable value adjustments.
C) With attention paid to the GEAR engagement, fasten SCREWs A.
- When needed, make further fine adjustments by loosening ADJUSTMENT SCREWs B
ACCELERATOR
Minimum value Maximum value
28H or lower BOH or higher
BRAKE
Minimum value Maximum value
>
28H or lower C8H or higher
SCREW “A”
SCREW “B” UA Minimum value:
Refers to value obtained
when you do not step on the pedal.
Maximum value:
Refers to the value
obtained when you fully step on the pedal.
- REPLACING THE START/LIGHT/WIPER BUTTONS
+ In the OUTPUT TEST MODE, when the START/LIGHT/WIPER BUTTONs do not light up, replace the BUTTONS in accordance with the following procedure:
SWITCH PLATE ScRENS. CLS. (RDN-1037) /
Va FIG. 2 HOOK
WIRE CONNECTION
White/Black Pink/White White Pink/Blue White Pink/Black fs Pa Light blue Light biue/thite] ®2S | Yeitow Light blue/Red[ 2 & & | Yellow Nel low Yellow 2 ke ° &
START BUTTON LIGHT BUTTON WIPER BUTTON
@ Take off the 3 TAMPERPROOF SCREWs which secure the SWITCH PLATE. @ Pull the SWITCH PLATE towards you and disconnect any of the abovementioned BUTTONS that might not light up. At this time, pay careful attention so that the wires do not go into the
DASHBOARD holes. @ Ina manner as shown in FIG. 2, remove the button (S) to be replaced and install a new BUTTON (s). @ In accordance with the wiring diagram, insert the WIRE CONNECTOR PIN and install the SWITCH PLATE in the procedure opposite to the above.
- BEAM SENSOR ADJUSTMENT
+ When adjusting the BEAM SENSOR, display the MOTOR TEST MODE (see page 39 ) screen.
WING BOLT “C” WING BOLT “B”
BEAM SENSOR
WING BOLT “A”
ADJUSTING THE COCKPIT SENSOR
+ In the MOTOR TEST mode, when the SENSOR A is ON, make
adjustments to the COCKPIT SENSOR shown in the FIGURE.
HOW-TO-ADJUST
Make adjustments by using the 3 WING BOLTs shown. Adjustments can be made in the up / down directions by using SCREW A and the left / right directions by using SCREW B and C. In the MOTOR TEST mode, make adjustment in a manner so that the "ON" letters for the SENSOR A goes off, or the BEAM SENSOR's LED (red) lights up.
ADJUSTING THE ASSY BASE SIDE SENSOR
@ Loosen TAMPERPROOF SCREWS A and B which secure the BEAM SENSOR and make adjustments of the SENSOR directions in a manner so as to ensure that the “ON" letters for SENSOR B, C, and D will
disappear.
@ With attention paid to the SENSOR directions, fasten TAMPERPROOF SCREWS A and B.
TAMPERPROOF SCREW A
TAMPERPROOF SCREW B
- MONITER CLEANING AND FLUORESCENT LAMP REPLACEMENT
MONITOR CLEANING
GLASS HOLDER MONITOR GLASS
4 TAMPERPROOF SCREWS (M5)
Take off the four TAMPERPROOF SCREWs (M5) and the 4 GLASS HOLDERs
to remove the MONITOR GLASS, and clean the CRT display surface.
FLUORESCENT LAMP REPLACEMENT
STARTER
FLUORESCENT LAMP
Loosen the four TAMPERPROOF SCREWS and remove the BILLBOARD to
replace the FLUORESCENT LAMP. 4 TAMPERPROOF SCREWs (M4)
- 26 INCH MONITOR
@ _ H-POSITION.
The image's horizontal position is adjustable
The horizontal image dimensions are adjustable. For adjustments, use a hexagonal driver
This adjusts the horizontal distortions.
The on-screen image's vertical distortion is adjustable.
The vertical image dimensions are adjustable.
The image's vertical position is adjustable
@ BRIGHT. This adjusts the on-screen image brightness
- PERIODICAL INSPECTION
Periodical greasing of the mobile parts are required Apply grease in accordance with the following instructions: Normally, replacement once in 2 months is recommended.
Lubricate the MECHANISM UNIT MECHANISM UNIT
and the CRANK UNIT are per the illustration. ® ROD END Apply grease to the surfaces of the A inner ring (diagonally lined portion as per the illustration).
BALL SCREW Apply grease to the screw surfaces by hand or by using a spatula.
ADJUST SHAFT Apply grease to the ADJUST SHAFT
When lubricating, so as not to cause any malfunction, make sure | that no foreign matter such as dust, etc. gets into the grease.
- TEST MODE
This test mainly checks the operation of game PCB's, discovers defects if any, and also checks monitor colors and audio quality. In addition, the test indicates Coin mode and has a Bookkeeping
function.
© Selection of test ITEMS
- Push the TEST SW to cause the following TEST ITEM MENU to
appear
Test mode
Individual
Bookkeeping Game & system setting Coin assignment Input test Output test Motor test Memory test Backup RAM clear > Bxit
Select by SERVICE and push TEST
- By pushing the SERVICE SW, bring the arrow mark “>” to the desired item and press the TEST button.
- When the test has been completed, bring “>” to EXIT and push the TEST button.
Bring “>” to “INDIVIDUAL” and push the TEST button to change it to “CONTINUE.”
Briging “>” to “CONTINUE” and pushing the TEST button without pressing the SERVICE button will change the screen sequentially.
1. Bookkeeping
Credit Report Coin chute #1 } ® #2 0 Coin credits 54 ® Service credits 6 ® Total credits @
Push TEST to return menu Push SERVICE to other page
@ Usage frequency of each COIN @ Usage frequency of each CHUTE SERVICE SW.
@ Total COIN CHUTE usage @ Total credits
frequency
Press the SERVICE SW button to display the following:
Time Report
Total time Total play time Sh 30m 44s @ Average play time Oh im 46s @ Longest play time @
Game Report
New games ®
Continue games 58 O°
Total play games
Push TEST to return menu Push SERVICE to other page
@ Machine's total energized time
© ® © @
iS) Total game play time
Average game play time
Longest game play time
New games
Continue games
Total play games
Press the TEST Button to cause the MENU mode to return on to the
screen.
Game & system setting
Game difficulty adjustment and the cabinet type are displayed.
Game mode > Game diffculty 8
Rasy WY
Starting timer (40~ 60s) 45 seconds
System mode
Advertise sound Screen mode off Norma! Cabinet type Deluxe
Select by START and change WIPER (+) and LIGHT (~) button Push TEST to return menu Push SERVICE to other page
Game difficulty Normally, 8 Play times setting Normally, 45 sec. Advertice sound
Normally, off Type of Screen mode Normally, Normal Type of Cabinet Normally, Deluxe ® ® © 8 9
Press the START button, bring the “>” to the item for which you desire to make a change, and then change the numerical value by using either the WIPER SW. or the LIGHT SW
Press the SERVICE BUTTON to have the following screen appear:
Game mode Page 2/2
> Rival car speed
Slow
Police car
Slow
Select by START and change WIPER (+) and LIGHT (-) button Push TEST to return menu Push SERVICE to other page
@ The rival cars' speed can be set (slowest, 1 + fastest, 16)
@ The police car speed can be set (slowest, 1». fastest, 16)
Press the START BUTTON to move the “>".
Bring the “>" to the desired item and press the WIPER or LIGHT Button to change the contents of the setting.
3 Coin assignment
Shows the number of credit(s) to start, and number of credit(s)
to CONTINUE.
Coin mode Page 1/2
> Credit to start 3 credit (continue 2 credit) Coin / Credit Setting 1 coin 1 credit _A — ®@ Chute #1 1 coin 1 credit Chute #2 1 coin 1 credit
Select by START and change WIPER (+) and LIGHT (-) button Push TEST to return menu Push SERVICE to other page
@ Number of credit(s) to start
@ Refers to the number of credits CONTINUE.
@ Twenty seven kinds of standerd coin modes can be selected.
@ Displays the COIN modes for COIN CHUTE#1 and #2
By pressing the START button, select the desired item, and the numeral can be increased or decreased by using either the WIPER SW, or the LIGHT SW.
Press the SERVICE button, and the following screen will appear
(this is applicable in cases other than standard COIN modes).
Coin mode Page 2/2 >Coin to credit coin 1 credit
Bonus Adder | (No bonus adder) Coin chute#l Multiplier 1 Coin counts as 1 coin coin credit
credit
Select by START and change WIPER (+) and LIGHT (-) button Push TEST to return menu Push SERVICE to other page
% Increase and decrease in numerals
The number of coins required for one credit.
Lets you choose from various kinds of bonuses of no bonus.
The number of coins each counts as in the coin chute#1.
The number of coins each counts as in the coin chute#2.
Press the START button to move the “>” Bring the “>” to
the desired item and press the WIPER or LIGHT Button to
change the contents of the setting.
® Coin to credit (The number of tokens required for one credit. )
coin
coin coin coin coin 1 credit coin
coin
coin wlolai ala) aloo!
coin
@® Bonus Adder (The number of inserted tokens required for a BONUS token) No bonus adder | No extra coin free play free play 2 coins give 3 coins give 4 coins give 5 coins give] 1 extra coin 6 coins give 7 coins give 8 coins give g coins give
@ COIN CHUT #1 Multiplier (The number of tokens the inserted token represents in Coin
Chute #1.)
coin coin
coin coin coin coin coin coin coin 1 coin counts as Carouktuone
coin chute #2 Multiplier Same as number @.
Input test
Indicates the condition of each switch and POTENTIOMETER.
Service Coinl PSWL Wiper INPUT TEST
Start Coin2 PSW2 Light Test
| 1 | 2 | 3 | 4 |
Dip SW OFF OFF OFF OFF
Handle 80
| ut | i | L |
| Left | Center | Right |
Brake Accele 28
| ZZ | > | ZA |
Low High Low > High
Push TEST to return menu
@ Indicates the condition of each switch. Operate each switch When the “OFF" condition is changed to “ON," the
corresponding switch is in good working order
@ It is satisfactory if data vales increase (higher than DO) when the steering wheel is moved to the right, decrease (lower than 30) when it is moved to the left,and indicate
"80H" when released.
«< HANDLE — 7CH DH 7EH ‘FH | 80H | 81H 82H 83H 84H Standard value
@ BRAKE / ACCELERATOR POTENTIOMETER VALUE If the data value increases when pressure is applied to the ACCELERATOR's of BRAKE's pedal, it tests out satisfactorily.
Minimum 28H or lower Maximum BOH or higher BRAKE
Minimum 28H or lower ACCELERATOR Maximum C8H or higher
< BRAKE . When pressure is not applied to 24H 25H 26H 27H| 28H the pedal, it is satisfactory if
the following value is obtained: Standard value
< ACCELERATOR BRAKE 28H or lower ACCELERATOR 28H or lower 24H 25H 26H 27H | 28H
Standard value
BRAKE — When pressure is fully applied to
BOH| BiH B2H B3H B4H the pedal, it is satisfactory if
Standard value the following value is obtained:
ACCELERATOR —> ——_ BRAKE C8H or higher C8H C9H CAH CBH CCH
- ACCELERATOR BOH or higher Standard value
beeen TEST Button to cause the MENU mode to return on to the
5 Output test
- C. R. T. TES’
@ Monitor adjustment check
OUTPUT TEST
TTT Tri CRT size test
Push TEST to return menu Push SERVICE to other page
Checks the C. R. T. position Make sure that the on-screen
corners are consistent and
then make size adjustments
@ _ RGB color check
OUTPUT TEST Page2/4 CRT coior test
RED
Push TEST to return menu Push SERVICE to other page
The color becomes blighter from the left to the right
@ Brightness check
Becomes brighter from the left (black) to the right (white).
- SOUND TEST
OUTPUT TEST Page3/4 SOUND TEST
1/52
Select WIPER (+) and LIGHT (-) Push START to listen music Push TEST to returo menu Push SERVICE to other page
Pushing WIPER SW. increases the number and pushing LIGHT SW.
decreases the number.
Push the START SW. when the desired number is shown.
- LAMP TEST
OUTPUT TEST Page 4/4
Lamp check
Push TEST to return menu Push SERVICE to other page
The LIGHT, WIPER and START LAMP will flash.
- MOTOR TEST
Manually move the COCKPIT and check the MOTOR, LIMIT SWes, etc. to see if they are satisfactorily operating.
MOTOR TEST deluxe f SENSOR A on cockpit SENSOR B base right-front | SENSOR C base right-rear SENSOR D base left ®
@ @ ® CABINET ANGLE 0 LEFT LIM -284 RIGHT LIM 291 Ge i re vn © iG) CONTROL ANGLE 0 Friction level 74 HANDLE to move machine Push TEST to return menu.
@ Indicates the condition of each BEAM SENSOR. If any one of these SENSORS shows “ON", the COCKPIT will not operate even during the TEST mode @ Shows the COCKPIT's banking angle in a numerical value. @ Indicates in a numerical value, the position of the LIMIT SW which determines that the COCKPIT has completely banked to the left. (Normally condition value -265+30) @ Shows in a numerical value, the position of the LIMIT SW which determines that the COCKPIT has completely banked to the right (Normally condition value 265+ 30) @® Indicates the numerical value which shows the COCKPIT's banked position. This value varies as the HANDLE is turned, and the COCKPIT's banking also varies in accordance with the value. @ MECHANICAL Friction level MACHINE'S Load level. (Normally condition value 55~110)
MESSAGE
Can't communicate
to drive BD.
or Not responded.
Right limit SW non ------
Left limit SW non
Center limit SW non. -----
Motor not move ------------
Cabinet not move --------- CONTENT OF MESSAGE AND MAIN CAUSES
- Can't communicate with the MOTOR CONTROL DRIVE
BD. There are irregularities in the MOTOR CONTROL BD., wiring, etc.
The LIMIT SW which determines that the COCKPIT has completely banked to the right does not function.
There are irregularities in the MICROSWITCH / WIRING.
- The LIMIT SW which determines that the
COCKPIT has completely banked to the left does not function. There are irregularities in the MICROSWITCH / WIRING
The MAGNET SW which determines that the
COCKPIT banking is in the neutral position does not function
There are irregularities in the MAGNET SW / WIRING.
The motor does not turn. There are
irregularities in the MOTOR, MOTOR DRIVER, WIRING, etc.
Due to mechanical load, the cabinet does not operate.
Unable to read Encoder for motor. ------ Motor speed measurement value is irregular. There are irregularities in the Encoder that measures motor Speed, wiring, etc.
Unable to read Encoder for bank position ------- The COCKPIT banking angle's measurement value is irregular. There are irregularities in the Encoder which measures the COCKPIT's banking angle, wiring, etc.
Press the TEST Button to cause the MENU mode to return on to the
screen.
Memory test Check the PCB's MEMORY ICs
When the IC is in good operating condition, “GOOD” will be indicated.
If there exists any malfunctioning of the IC's, “BAD” will be indicated.
MEMORY TEST
- * ROM TEST * #
21 GOOD 37 GOOD
- * RAM
16 GOOD G00D 37 «GOOD Good 62 GOOD GOOD 64 GOOD GOOD G00 Good GOOD Goob 71 GOOD y GOOD 75 GOOD
Push TEST to return menu
Backup RAM clear
The BOOKKEEPING data can be cleared. When clearing, bring “>” to “YES” and when not clearing, to “NO,” by using the SERVICE SW, and then push the TEST button.
BACKUP RAM CLEAR
YES (Clear)
> NO (Cancel)
Select by SERVICE and push TEST
20. COIN/CREDIT SETTING
COIN/CREDIT SETTING COIN CHUTE #1 COIN CHUTE #2
| 1 Coin 1 Credit-A | 1 Coin 1 Credit | 1 Coin 1 Credit |
| -B | 1 Coin 1 Credit | 1 Coin 2 Credits |
| -¢ | 1 Coin 1 Credit | 1 Coin 3 Credits |
| ~D | 1 Coin 1 Credit | 1 Coin 4 Credits |
| -B | 1 Coin 1 Credit | 1 Coin 5 Credits |
| 1 Coin 2 Credits-A | 1 Coin 2 Credits | 1 Coin 2 Credits |
| ~B | 1 Coin 2 Credits | 1 Coin 5 Credits |
| 1 Coin 3 Credits- | 1 Coin 3 Credits | 1 Coin 3 Credits |
| 1 Coin 4 Credits~ | 1 Coin 4 Credits | 1 Coin 4 Credits |
| 1 Coin 5 Credits- | 1 Coin 5 Credits | 1 Coin 5 Credits |
| 1 Coin 6 Credits~ | 1 Coin 6 Credits | 1 Coin 6 Credits |
| 2 Coins 1 Credit-A | 2 Coins 1 Credit | 2 Coins 1 Credit |
| -B | 2 Coins 1 Credit | 1 Coin 1 Credit |
| -¢ | 2 Coins 1 Credit | 1 Coin 2 Credits |
| 2 Coins 3 Credits-A | 1 Coin 1 Credit | 1 Coin 1 Credit |
2 Coins 3 Credits 2 Coins 3 Credits
| 2 Coins 3 Credits-B | 1 Coin 1 Credit | 1 Coin 3 Credits |
2 Coins 3 Credits
| 3 Coins 1 Credit | 3 Coins 1 Credit | 3 Coins 1 Credit |
| 4 Coins 1 Credit | 4 Coins 1 Credit | 4 Coins 1 Credit |
| 4 Coins 5 Credits-A | 1 Coin 1 Credit | 1 Coin 1 Credit |
2 Coins 2 Credits 2 Coins 2 Credits 3 Coins 3 Credits 3 Coins 3 Credits 4 Coins 5 Credits 4 Coins 5 Credits
| 4 Coins 5 Credits-B | 1 Coin 1 Credit | 1 Coin 5 Credits |
2 Coins 2 Credits 3 Coins 3 Credits 4 Coins 5 Credits
| 5 Coins 2 Credits | 3 Coins 1 Credits | 1 Coin 2 Credits |
5 Coins 2 Credits
| 5 Coins 3 Credits-A | 2 Coins 1 Credit | 2 Coins 1 Credit |
4 Coins 2 Credits 4 Coins 2 Credits 5 Coins 3 Credits 5 Coins 3 Credits
| 5 Coins 3 Credits-B | 2 Coins 1 Credit | 1 Coin 3 Credits |
4 Coins. 2 Credits 5 Coins 3 Credits
| 5 Coins 6 Credits-A | 1 Coin 1 Credit | 1 Coin 1 Credit |
2 Coins 2 Credits 2 Coins 2 Credits 3 Coins 3 Credits 3 Coins 3 Credits 4 Coins 4 Credits 4 Coins 4 Credits 5 Coins 6 Credits 5 Coins 6 Credits
| 5 Coins 6 Credits-B | 1 Coin 1 Credit | 1 Coin 6 Credits |
2 Coins 2 Credits 3 Coins 3 Credits 4 Coins 4 Credits 5 Coins 6 Credits
| 5 Coins 12 Credits | 1 Coin 2 Credits | 1 Coin 6 Credits |
2 Coins 4 Credits 2 Coins 12 Credits 3 Coins 7 Credits 4 Coins 9 Credits 5 Coins 11 Credits
free play free play free play
- ROM LOCATIONS
SY 32 ROM BD
EPR-13526 IC 38
EPR-13525 IC 37
EPR-13690 (USA) BPR-13893 (EXP) 1C2l
MPR-13699 IC 20
MPR-13523 MPR-13522 MPR-13518 MPR-13514
| Ic 14 | IC 18 | Ic 17 | IC 16 |
EPR-13527 MPR-13521 MPR-13517 MPR-13513
| Ic 9 | IC 12 | 1c 11 | Ic 10 |
MPR-13520 MPR~13516 MPR-13512
| Ic 7 | Ic 6 | Ic 5 |
MPR-13519 MPR-13515 MPR-13511
| Ic 3 | Ic 2 | 1c 1 |
RAD MOBILE
| IC LOCATION | ROM NUMBER | MAIN WORK |
| 1 Ic 1 | MPR-13511 | 8M |
| 2 Ic 5 | MPR-13512 | 8M |
| 3 Ic 10 | MPR-13513 | 8M |
| 4 Ic 16 | MPR-13514 | 8M OBJECT |
| 5 Ic 2 | MPR-13515 | 8M |
| 6 Ic 6 | MPR-13516 | 8M |
| 7 Ic 11 | MPR-13517 | 8M |
| 8 Ic 17 | MPR-13518 | 8M |
| 9 Ic 3 | MPR-13519 | 2M |
| 10 Ic 7 | MPR-13520 | 2M SCROLL |
| ll IC 12 | MPR-13521 | 2M |
| 12 Ic 18 | MPR-13522 | 2M |
| 13 1c 9 | EPR-13527 | 1M |
| 14 1c 14 | EPR-13523 | 4M SOUND |
| 15 Ic 20 | EPR-13699 | 4M |
| 16 IC 37 | EPR-13525 | AM MAIN |
| 17 IC 38 | EPR-13526 | 4M PROGRAM |
18 Ic 21 EPR-13690 EPR-13693 IM |
ROM BOARD USA ROM BD EXPORT ROM BD PART NO. 834-7739-01 | 834-7739-02 l
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
- VOLTAGE CHANGES TO LOCAL REQUIREMENTS
2)
3) Voltage changes to 90V, 100V, 110V, 120V, 200V, 220V, 230V, and 240V can be made in accordance with the following procedure: If the voltage setting to local requirements is incorrectly performed, this may cause machine malfunctioning or breakage to occur, therefore, pay sufficient attention when setting the voltage.
TRANSFORMER'S (560 - 5148) primary - voltage change: In accordance with the voltage table printed on the side of the TRANSFORMER, pull out the primary side CONNECTOR's (white, 9P socket) purple lead wire's pin and insert it into the applicable position.
SW REGULATOR's (400 - 5055) primary voltage change Where necessary, reinsert the TAP which is seen from the oval opening on the side of the SW REGULATOR (400 - 5055) into the applicable position in accordance with the sticker applied near the opening.
DC MOTOR DRIVER's (400 - 5117Y) primary - voltage change Reinsert the TAP which is seen from the oval opening on the top of DC MOTOR DRIVER (400 - 5117Y), into the applicable position in accordance with the sticker applied near the opening.
MOTOR CONTROL BOARD's (DRIVE BD : 837 - 7753) DIP SW change : Set the MOTOR CONTROL BOARD's central DIP SW in accordance with the following Table :
1 2 3 4
| Local | 90V, 100V, 200V | OFF OFF | OFF | OFF | ||
| Voltage | 110V, 220V | ON | ON | OFF | OFF |
| Requirements | 120V, 230V, 240V | ON | OFF | OFF | OFF |
- PARTS LIST @ TOP ASSY RAD MOBILE DX (RDM-—0000) (D-1/5)
@ TOP ASSY RAD MOBILE DX (RDM-—0000) (D-2/5)
ITEM NO.| PART NO, DESCRIPTION NOTE
| 1 | RDM-0500 | ASSY TOWER & STEP | |
| | | 2 | RDM-1000 | ASSY COCKPIT |
| 3 | RDM-3000 | ASSY BASE | |
| 4 | RDM-~1100 | ASSY MONITOR | |
| 5 | RDM-1012 | ASSY MONITOR COVER FRONT | |
| 6 | RDM-—4000 | ASSY PWR SPLY | |
| 7 | RDM~4100 | ASSY DRIVE SPLY | |
| 8 | 833-7738 | GAME BD RAD MOBILE | |
| 9 | SGM-3901 | POLYETHYLENE COVER 1100x1750x1700 | |
| 10 | 421—7010-01 | STICKER CAUTION ENG | |
| i | RDM-—0001 | SHIPPING PLATE | |
| 13 | 421-6594 | STICKER SERIAL NO. INFO | |
| 14 | 421-6673 | STICKER SERVICE INSTR | |
| 15 | 421-6671 | STICKER DANGER HIGH VOLTAGE | |
| 16 | 421-5564 | STICKER INDOOR | |
| 18 | 117-5039 | PLATE ELEC. SPEC | |
| 20 | 421-6241 | STICKER DANGER ENG |
21 421-5800-142 | ORIGINAL SEAL RAD MOBILE
| 22 | 220-5254 | KEY MASTER FOR 220-5253 |
SGB-1035X KEY BAG 421-7689 STICKER CAUTION BAG
| 25 | 421-7020 | STICKER CAUTION FORK |
| 26 | 421-7692 | STICKER CAUTION VOLTAGE |
| 27 | RDM-—0002 | BUMPER PLATE |
@ TOP ASSY RAD MOBILE DX (RDM-0000) (0-3/5)
ITEM NO. PART NO, DESCRIPTION NOTE
| 28 | 422-0364-01 | PLAY INSTR STICKER RAD MOBILE DX ENG | |
| 29 | 422-0373-01 | SUBPLAY INSTR STICKER RDM ENG (NEW) | |
| 30 | RDM-~1302 | DESIGN PLATE BILLBOARD | |
| 31 | RDM~1304 | LOWER HOLDER | |
| 32 | RDM-0004 | STAY | |
| 33 | RDM-—0005 | SIDE STOPPER | |
| 35 | RDM-0006 | FRAME COVER R | |
| 36 | RDM-0007 | FRAME COVER L | |
| 37 | 421—7868-01 | STICKER DANGER ENG | |
| 38, | 421—7869-01 | STICKER CONTINUE ENG | |
| 39 | 421—7873-01 | INSTALLATION INSTR SH RDM ENG | | |
| 40 | 429-0058-01 | DISPLAY PLATE RAD MOBILE DX ENG | |
| 201 | 050-0010 | HEX NUT M10 | |
| 202 | 060-0010 | FLT WSHR M10 | |
| 203 | 061-0010 | SPR WSHR M10 | |
| 204 | 030-0820-B | HEX BOLT BLK M8x20 | |
| 205 | 069-0048 | FLT WSHR BLK 8.5-22x1.6 | |
| 206 | 069-0026 | SPR WSHR BLK M8 | |
| 207 | 008-0416 | TMP PRF SCR TH M4x16 | |
| | | 208 | 053-0005 | WING NUT M5 |
| 209 | 061-0005 | SPR WSHR M5 | |
| 210 | 069-0001 | FLT WSHR 5.5-20x1.6 | |
| 211 | 001-0310 | M SCR FH M3x10 | |
| 212 | 030-0820 | HEX BOLT M8x20 | |
| 213 | 060-0008 | FLT WSHR M8 |
@ TOP ASSY RAD MOBILE DX (RDM-—0000) (D-4/5)
ITEM NO. PART NO. DESCRIPTION NOTE
| 214 | 061-0008 | SPR WSHR M8 |
| 215 | 008-0408 | TMP PRF SCR TH M4x8 |
| 216 | 069-0055 | FLT WSHR SPECIAL BLK 4,4-16x1.6 |
| 217 | 047-0001 | RVT OPEN TYPE 3.2x4,4 |
| 218 | 039-0098 | HEX BLT BLK W/S M8x35 |
| 219 | 009-0825 | TMP PRF SCR BH M8x25 |
301 | 280-5008 CORD CLAMP 615
| 302 | 280-5009 | CORD CLAMP $421 |
303 | 280-5126 CORD CLAMP 425
| 401 | 601-6604—70 | CARTON BOX 70 |
| 402 | 420-5976-01 | OWNERS MANUAL RAD MOBILE DX |
| 403 | SGM~2675 | POLYETHYLEN BAG 240x370 |
| 404 | 421—1835-02 | ADJUST INSTR SH RAD MOBILE DX ENG |
| 405 | 420-5881 | DSPL MANUAL 26” 200-5112-24 ENG |
420-5929 DSPL MANUAL 26” 200-5180 ENG
| 406 | 1039 | SCHEMATIC DIAGRAM SEGA RAD MOBILE DX |
4o7 | 509-5218, PUSH BTN SW IT YELLOW W/LAMP
| 408 | 220-5130 | VOL CONT B-5KOHM |
499 | RDM-2006 —) EXT SPRING
| 410 | 540-0006-01 | WRENCH FOR TAMP PRF SCR DUAL TYPE M4 |
540-0018 DRIVER FOR TAMP PRF SCR M4
| 4 | 540-0009-01 | WRENCH FOR TAMP PRF SCR DUAL TYPE M8 |
| 412 | 090-0044 | GREASE NET 300g |
| 413 | 509-5372 | PUSH BUTTON SWITCH 1T GREEN W/LAMP |
@ TOP ASSY RAD MOBILE DX (RDM-0000) (D-5/5)
ITEM NO, PART NO. DESCRIPTION NOTE 413 509-5373 PUSH BUTTON SWITCH 1T BLUE W/LAMP 414 RDM-~1212 TORSION SPRING R 415 | RDM-1213 | TORSION SPRING L
RDM-—0003 SHIPING PLATE FOR EXPORT 060-0008 FLT WSHR M8 030-0830 HEX BOLT M8x30 421-6653-01_ | TAG FOR SHIPPING ENGLISH 421-7048 STICKER CAUTION KEEP HANDS OFF
421-6482-01__| STICKER CAUTION ENG 421-6094 STICTER CAUTION ENG
(D-1/2) @ ASSY SHIELD CASE (RDM—0100)
SERBS Thc
CPY Yee)
& O
&
@ _ ASSY SHIELD CASE (RDM-0100) (D-2/2)
ITEM NO.} PART NO. DESCRIPTION
1 RDM-0101 SHIELD CASE
2 RDM-0102 SHIELD CASE COVER
3 RDM-0103
4 RDM-0104 BOARD STOPPER
STOPPER RUBBER
5 RDM-0123 LID
101 280-5079 NYLATCH GROMET
102 280-5080 NYLATCH PLUNGER
103 839-0395 FLT BD SYS 32
201 010-0306-F S-TITE SCR PH W/F M3x6
202 000-0308 M SCR PH M8x8
203 000-0510-FS M SCR PH W/FS M5x10
301 600-6025-07 WIRE HARN JST 4P
302 600-6025—-08 WIRE HARN JST 18P
303 421-5563 STICKER ARROW
i I fei] ih TG OG EE C Cpos.d/) tor arate
see B
(pes. EF ) @ _ ASSY COIN CHUTE TOWER (RDM-0501) (D- 1/3)
® ASSY COIN CHUTE TOWER (RDM-—0501) (D-2/3)
ITEM NO.| PART NO. DESCRIPTION 1 | RDM-0502 ‘| COIN CHUTE TOWER
| 2 | | GLC-0s02 | COIN METER PLATE |
| 3 | | GLc-0s03 | COIN CHUTE LOWER |
| 4 | | Guc-os04 | SQUARE HOLES COVER |
5 | RDM-0504 | sw UNIT 6 | pp-ue7 NG LKG
| 7 | | HIN-1050 | SPACER RING |
| 8 | | 105-5068 | PLATE TONGUE STOPPER |
9 | 109-0045 KEY HOLDER 10 | KR-1607x —_| CASH BOX u | KR-1608 LOCK BRACKET
| 12 | | stc-o19 | COIN METER LID |
13 | 421-e591-01 | STICKER COIN METER (RCAETER]
| 4 | | a21-cese | STICKER SERVICE INSTR | (| |
15 | 421-7501-02 | STICKER 6.3V 0.15A
| 16 | | KR-1408 | DENOMINATION PLATE |
17 | MX-1103-05 | DENOMINATION SHEET 1 GAME, 200F9 MX-1103-04 | DENOMINATION SHEET 1 GAME, 10/4
101 | 220-s046-91 | MAGNETIC LOCK W/KEY 102 | 220-5064 MAG CNTR 6 DIG DC 5V W/L & Dio
| 103 | | 220-5253 | MAGNETIC LOCK MASTER W/O KEY |
104 | 220-5220 CASH BOX DOOR 105 | 220-5282-01 | ASSY COIN CHUTE DOOR W/HOLE ¥100 106 |. 601-0460 TIE BELT 85mm 107 | 280-0425 CORD CLAMP 100
—5b-
® ASSY COIN CHUTE TOWER (RDM-0501) (D-3/3)
ITEM NO.| PART NO. DESCRIPTION NOTE 108 | 280-5008 CORD CLAMP 415 109 | 280-5009 CORD CLAMP ¢21
201 000-0306-F M SCR PH W/F M3x6 202 | 000-0410-FS__ | M SCR PH W/FS M4x10 203 | 000-0430 M SCR PH M4x30 204 | 010-0408-F S-TITE SCR PH W/F M4x8 205 | 008-0410 TMP PRF SCR TH M4x10 206 | 039-0095 CRG BLT BLK Mex15 207 | 051-0006 FLG NUT M6 208 | 060-0010 FLT WSHR M10
@ SW UNIT (RDM-0504)
Cc
| DEMAG. | SERVICE | TEST | MAIN |
| SW | SW | SW | SP. |
2 (00
ITEM NO. | PART No. DESCRIPTION NOTE
| 1 | KR-1405 | SW BRACKET | a |
| 2 | 421-7342 | STICKER SW UNIT | cI | |
| 101 | 220-5179 | VOL CONT B-5K OHM | 3 | |
| 102 | 509-5028 | sw PB 1M | & | |
| 103 | 601-0042 | KNOB 22mm | kay |
ie (/-a) (0001-Wdy) LIdxD00 ASSV @)
® ASSY COCKPIT (RDM-1000) (D-2/4)
ITEM NO.| PART NO, DESCRIPTION
1 RDM-1001 BODY COWL
2 RDM-—1002 ASSY DASHBOARD
3 RDM-1003 ASSY MONITOR BASE
4 RDM-1007 BONNET PLATE
5 RDM-—1200 ASSY ACCEL & BRAKE
7 RDM-—1009 DASHBOARD LID
8 RDM~1016 DASHBOARD PLATE
18 RDM-—2000 ASSY HANDLE MECHA
19 RDM-—2020 ASSY VR
20 RDM-—2030 ASSY HANDLE BASE
21 RDM-—2001 STEERING WHEEL $270
22 RDM—2002 STEERING SHAFT
23 RDM-—2004 CAM
24 RDM-—2005 STEERING SHAFT COLLAR
25 RDM-2006 EXT SPRING
RDM-—2007 ADJUST RING
27 HSD-2019 KEY 4x4x12
RDM-1017 SHIFT LEVER BANDAGE
RDM-~2012 STEERING EMBLEM
31 RDM-1030 TAIL LAMP PLATE R
32 RDM-1031 TAIL LAMP PLATE. L
33 RDM-1019 HOLDER PLATE
35, RDM-2013 CAM SPACER
37 RDM-1034 WIRE TRAY
38 RDM~1035 WOODEN BASE HOLDER
39 RDM-—1036 WIRE RAIL
® ASSY COCKPIT (RDM-1000) (D-3/4)
| 40 | RDM-—1040 | ASSY COCKPIT SENSOR |
| 41 | RDM-1045 | SPEAKER HOLDER |
| 101 | 601-6109 | GEAR 60 |
| 102 | 390-5157 | LAMP 110V 10W |
| 103 | 214-0111 | | LAMP SOKET W/WIRE |
| 202 | 030-0825 | HEX BLT |
| 204 | 000-0408-FS | M SCR PH W/FS M4x8 |
| 205 | 008-0416 | TMP PRF SCR TH M4x16 |
| 206 | 008-0416 | TMP PRF SCR TH M4x10 |
| 207 | 059-0016 | HEX NUT M14 |
| 209 | 050-0008 | HEX NUT M8 |
| 210 | 050-0004 | HEX NUT M4 |
| 211 | 054-0006 | U-NUT M6 |
| 212 | 028-0019 | SET SCR HEX SKT CP UNBR M4x8 |
| 214 | 060-0008 | FLT WSHR M8 |
| 215 | 060-0006 | FLT WSHR M6 |
| 217 | 061-0008 | SPR WSHR M8 |
| 218 | 061-0004 | SPR WSHR M4 |
| 219 | 069-0019 | SPR WSHR Mi4 |
| 221 | 069-0048 | FLT WSHR BLK 8,5-22x1.6 |
| 222 | 069-0045 | FLT WSHR M14 |
| 224 | 008-0516 | TMP PRF SCR TH M5x16 |
| 301 | SGB-4084~21 | WIRE HARN SP EXT 2 |
® ASSY COCKPIT (RDM—1000) (D-4/4)
ITEM NO, PART NO. DESCRIPTION
211-5282—-06GR CONN PLUG 9090 06P-GR
211--5283-02BK CONN CAP 9090 02P-BK
211—5283-02BL CONN CAP 9090 02P—BL
211-5284 CONN PIN 9090 AWG 18-24
211-5287 CONN SOCKET 9090 AWG 18-24
310-5028- 8.3 VINYL TUBE 48.3
SGB—4084—29 WIRE HARN CONTROL EXT
211-5282-15RE CONN PLUG 9090 15P—RE
211-5283-030R CONN CAP 9090 03P—OR
211-5283-04WH| CONN CAP 9090 04P-WH
211-5283-04YE CONN CAP 9090 04P-YE
211—5283-02WH| CONN CAP 9090 02P-WH
211—5283-03WH, CONN CAP 9090 03P—WH
211-5284 CONN PIN 9090 AWG 18-24
211-5287 CONN SOCKET 9090 AWG 18-24
211-5286 CONN PIN 9090 AWG 14-20 L
310-5028-11,1 VINYL TUBE ¢11,1
310-5028-7.3 VINYL TUBE $7.3
SGB-4084-32 WIRE HARN BRAKE LAMP
211-5274-02WH| CONN PLUG AMP MINI 02P-WH
211-5278 CONN PIN AMP MINI AWG 22-18
209-0023 CONN CLOSED END
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
@ ASSY START BUTTON (RDM-1010)
(2/) CYELLOw)
(GREEN)
CRLUE)
ITEM NO.| PART NO. DESCRIPTION NOTE
| 2 | RDM-1037 | SW PLATE | SE. |
| 101 | 509-5218 | PUSH BTN SWITCH IT YELLOW W/LAMP | |
| 102 | 509-5372 | PUSH BUTTON SWITCH IT GREEN W/LAMP | |
| 103 | 509-5373 | PUSH BUTTON SWITCH IT BLUE W/LAMP |
ASSY COCKPIT SENSOR (RDM-—1040) (D-1/2)
RDA- /20/7
ASSY COCKPIT SENSOR (RDM-1040) (D-2/2)
ITEM NO. PART NO. DESCRIPTION NOTE |
| 1 | RDM-1041X | SENSOR BACKET |
| 2 | RDM-—1042X | SENSOR HOLDER |
| 3 | RDM-1043 | COMP SPRING |
| 4 | RDM—1044 | REFLECTOR BRACKET |
| 5 | RRR-1076 | FRANGE |
| 101 | 370-5042 | BEAM SENSOR |
| 102 | 601-6576 | RUBBER GROMMET |
| 201 | 032-0530 | WNG BLT M5x30 |
| 202 | 069-0022 | FLT WSHR 5.5-14x1 |
| 203 | 029-0119 | TMP PRF SCR TH CHROME M4x12 |
| 204 | 029-0169 | TMP PRF SCR TH CHROME M4x16 |
| 205 | 051-0004 | FLG NUT M4 |
(©) ASSY MONITOR (RDM-—1100)
@ ah
(rN) (D-1/2)
© ASSY MONITOR (RDM-1100) (D-2/2)
ITEM NO.| PART NO, DESCRIPTION NOTE
| 1 | RDM-1101 | MONITOR COVER REAR |
| 2 | RDM~1102 | MONITOR HOLDER |
| 3 | RDM~1103 | MAINTENANCE LID |
| 4 | 280-5112 | BUSH FOR TV |
| 5 | 280-5113 | COLLAR FOR TV |
| 6 | 280-5114 | SPACER 6.4-25x2 |
| 101 | 200-5112-15 | ASSY CLR DSPL 26 TYPE 15K 100V |
200-5180-15 ASSY CLR DSPL 26 TYPE 15K 100V
| 201 | 039-0120 | HEX BOLT M6x35 |
| 202 | 061-0006 | SPR WSHR M6 |
| 203 | 030-0820 | HEX BOLT M8x20 |
| 204 | 061-0008 | SPR WSHR M8 |
| 205 | 008-0412 | TMP PRF SCR M4x12 |
| 206 | 060-0008 | FLT WSHR M8 |
| 301 | 280-5008 | CORD CLAMP ¢15 |
ASSY ACCEL & BRAKE (RDM-1200) (D-1/3)
SOOO
- ASSY ACCEL & BRAKE (RDM-1200) (D-2/3)
ITEM NO. PART NO. DESCRIPTION NOTE
| 1 | RDM-1201 | FOOT PEDAL BASE | |
| if | 2 | RDM~1202 | ACCEL PEDAL |
| 3 | RDM-~1203 | BRAKE PEDAL | |
| 4 | RDM~—1204 | SIDE PLATE | |
| 5 | RDM-~1205X | FOOT PEDAL COVER | |
| 6 | RDM-1206 | TOP COVER | |
| 7 | RDM-1207 | SWING ARM | |
| 8 | RDM-1208 | LINK ROD | |
| 9 | RDM-1209 | SPRING STOPPER PIN | |
| 10 | RDM~1210 | VR BRACKET | |
| 1 | RDM-1211 | BUMPER | |
| 12 | RDM-1212 | TORSION SPRING R | |
| 13 | RDM-1213 | TORSION SPRING L | |
| 14 | GLC--2122 | GEAR PLATE | |
| 15 | RDM-1214 | PROTECTOR | |
| 101 | 220-5130 | VOL CONT B-5K OHM | |
| 102 | 601-6005 | ADJUST GEAR | |
| 103 | 601-5943 | GEAR 20, $15 | |
| 104 | 601-5472 | RUBBER STOPPER | |
| 201 | 030--0820-B | HEX BLT BLK M8x20 | |
| | 202 | 000-0510-FS | M SCR PH W/FS M5x10 | |
| 203 | 000-0408-S | M SCR PH W/S M4x8 | |
| 204 | 008-0408 | TMP SCR TH M4x8 |
050-0008 HEX NUT M8 | ™
@ ASSY ACCEL & BRAKE (RDM—1200) (D-3/3)
ITEM NO,| PART NO. DESCRIPTION NOTE 206 | 069-0026 SPR WSHR BLK M8 207 ‘| 069-0035 FLT WSHR BLK M8 208 | 065-0006 E RING 6mm 209 | 069-0106 FLT WSHR 4.4-12x1.6 210 | 047-0001 RVT OPEN TYPE 3.2x4.4 211 ‘| 010-0408-F S-TITE SCR PH W/F M4x8 212 | 028-0003 SET SCR PH SPCL M3x8 213 | 069-0055 FLT WSHR SPECIAL BLK 4.4-16x1.6 214 | 000-0410-S M SCR PH W/S M4x10
@ Assy BILLBOARD (RDM-1300) (0-1/2)
(©) ASSY BILLBOARD (RDM-—1300) (D-2/2)
ITEM NO.| PART NO. DESCRIPTION NOTE
| 1 | RDM-1301 | BILLBOARD BOX | <2 |
| 3 | | RDM-1303 | UPPER HOLDER | nn |
5 | RDM-1305 | BOX HOLDER R B&B 6 | RDM-1306 | BOX HOLDER L Q
| 7 | RDM-1307 | TAIL PIPE | CB |
101 | 390-5108-02 | ASSY FL LIGHT 15W 50Hz MELLOW LOOK
| 102 | | 117-5167 | TERMINAL 5P-2Px2 SHORT |
201 | 030-0835 HEX BOLT M8x35 202 | 008-0416 TMP PRF SCR TH M4x16 203 | 005-3113-F | W SCR RH W/F 3.1x13 204 | 060-0008 FLT WSHR M8 205 | 061-0008 SPR WSHR M8
| 206 | 050-0008 | HEX NUT MB | | | | |
27 | 005-3190-F | W SCR RH W/F 3,1x20
r
@ ASSY HANDLE MECHA (RDM-—2000) (D-1/2)
©) ASSY HANDLE MECHA (RDM~—2000) (D-2/2)
[em No.| PART NO. DESCRIPTION NOTE
| 1 | RDM-2003 | | MECHA BASE | Gets |
2 | RDM-2008 | sWING ARM fo
| 3 | RDM—2009 | PIN | O=» | |
| 4 | | RDM-2010 | SPACER | OQ |
101 | 100-s018 BALL BEARING 48 102 | 100-5096 BEARING $17 ir
201 | 069-0020 FLT WSHR M12 202 | 060-0008 FLT WSHR M8 203 | 065-0008 E RING 8mm 204 | 065-0006 E RING 6mm | | 205 | 050-0006 HEX NUT M6 206 | 061-0006 SPR WSHR M6
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Ce) ASSY HANDLE BASE (RDM—2030)
rT ITEM NO.| PART NO. DESCRIPTION
| 1 | RDM-2031 | HANDLE BASE |
| 3 | RDM—2033 | STOPPER BRACKET |
| 4 | RDM-—2034 | STOPPER SHAFT |
| 5 | RDM-—2085 | STOPPER RUBBER |
| 101 | 100-5096 | BEARING 617 |
| 202 | 039-0005 | HEX BOLT M6x16 |
| 203 | 050-0008 | HEX NUT M8 |
| 204 | 050-0006 | HEX NUT M6 |
| 205 | 061-0008 | SPR WSHR M8 |
| 206 | 061-0006 | SPR WSHR M6 |
| 207 | 001-0520 | M SCR FH M5x20 |
@® ASSY BASE (RDM-3000) (D-1/4)
LIEL BH GM be
@) ASSY BASE (RDM-3000)
ITEM NO. PART NO, DESCRIPTION 1 | RDM-s001x | BASE
| 2 | |RDM-3002 | ‘| BASE COVER REAR |
3 | RDTM-3003X | BASE COVER FRONT
| ‘4 | | RDM~3004 | CRANK COVER |
5 | RDM-3005X | BASE COVER LEFT 6 | RDM-~s006 PILLAR JOINT
| 7 | | RDM-3007 | ‘| HOLE BANDAGE |
8 | RDM-3008 ‘| BEARING STOPPER
| 9 | | RDM-s009 | REFLECTOR HOLDER |
| 10 | | RDM-3010 | ASSY BEAM SENSOR |
1 | RDM-s020 ‘| ASSY ENCORDER 12 | RDM-3100 ASSY MECHANISM
| 13 | | RDTM-320 | ASSY CRANK |
| 14 | | RDM-3300 | ASSY AC UNIT |
15 | RDM-3014 GUIDE RING
| 16 | | YZ~3203 | ASSY MOTOR |
17 | RDM-sis0 ‘| ASsY LIMIT SWITCH
| 18 | | RDM-3015 | | BANK FRAME | |
| 19 | | RDM-3016 ‘| SHOULDER SCREW | or” " | |
| 20 | | RDM-3017 | ROD END COLLAR | & |
| 21 | | RDM-301i8 | | CON ROD COVER | OC |
| 22 | | RDM-3019 | | BASE COVER CENTER | hae |
| 23 | | DP-1167 | TNG LKG | iS, |
| 24 | | GLC-3021 | ROD END COLLAR | ® |
| 25 | |.RDM-3022 | | GUARD PLATE |
RDM-3023 RUBBER FLAP
@ ASSY BASE (RDM-3000) (D-3/4)
ITEM NO.| PART NO. DESCRIPTION NOTE 27 | RDM-30%4 FLAP HOLDER 28 | RDM~-3025 WIRE COVER 30 | RDM-s026 MAT LEFT
| a1 | | RDM-3027 | MAT GUARD L |
| 32 | | RDM-3028 | SIDE WALL R |
| 33 | | RDM-3029 | SIDE WALL L |
| 34 | | RDM-3030 | BANDAGE |
35 | RDM~3031 WIRE GUIDE 36 | RDM-3032 CONNECTOR HOLDER
| 37 | | RDM~1300 | ASSY BILLBOARD |
RDM-3033 UNDER GUARD R RDM-3034 UNDER GUARD L
| 40 | | RDM-3035 | REAR GUARD | |
| 101 | 100-5044 | BEARING #30 | 6 | |
| 102 | 601-6642 | GEAR 60/120 | 7) | |
| 103 | | 350-5137 | V BELT | -_ |
| 104 | 100-5031 | BEARING UNIT | EDP | |
| 105 | 130-5059 | SUPER WOOFER BOX | oe |
106 | 280-5122 CORD CLAMP
| 107 | 220-5253 | MAGNETIC LOCK MASTER W/O KEY | oe |
201 | 008-0410 TMP PRF SCR M4x10 202 | 059-0022 HEX NUT Mi6 203 | 069-0060 SPR WSHR M16 204 | 000-0410-FS__ | M SCR PH W/FS Max10
@® ASSY BASE (RDM-3000) (D-4/4)
ITEM NO. PART NO. DESCRIPTION NOTE
| 205 | 050-0010 | HEX NUT M10 | |
| [ | 206 | 061-0010 | SPR WSHR M10 |
| 207 | 060-0010 | FLT WSHR M10 | |
| 208 | 059-0016 | HEX NUT M14 |
209 | 069-0019 SPR WSHR M14
| 210 | 069-0045 | FLT WSHR M14 |
| 211 | 028-0019 | SET SCR HEX SKT CP UNBR M4x8 |
| 212 | 059-0017 | HEX NUT P=1,75 M12 |
| 213 | 069-0030 | SPR WSHR M12 |
| 214 | 069-0020 | FLT WSHR M12 |
| 215 | 005-3513-F | W SCR RH W/F 3.5x13 |
| 216 | 050-0008 | HEX NUT M8 |
| 217 | 061-0008 | SPR WSHR M8 |
| 218 | 060-0008 | FLT WSHR M8 |
| 219 | 008-0408 | TMP PRF SCR TH M4x8 |
| 220 | 053-0004 | WING NUT M4 |
| 221 | 061-0004 | SPR WSHR M4 |
| 222 | 000-0512-S | M SCR PH W/S M5x12 |
| 223 | 039-0096 | HEX BLT M4x40 |
| 224 | 039-0119 | HEX BLT BLK M8x60 |
| 225, | 069-0048 | FLT WSHR BLK 8.5-22x1.6 |
| 226 | 069-0026 | SPR WSHR BLK M8 |
| 227 | 005-3516 | W SCR RH 3.5x16 |
@ ASSY BEAM SENSOR (RDM-3010)
ITEM NO.| PART NO. DESCRIPTION NOTE
| 1 | | RDM-3011 | SENSOR COVER | ro | |
| 2 | |RDM-3012 | SENSOR HOLDER | La | |
| 101 | | 370-5042 | BEAM SENSOR | OD |
201 | 008-0408 TMP PRF SCR TH M4x8
301 | sGB-4og4-39 | WIRE HARN SENSOR i | 211-5274-03WH| CONN PLUG AMP MINI 03P-WH 211-5278 CONN PIN AMP MINI AWG 22-18 209-0028 CONN CLOSED END 601-0460 PLASTIC TIE BELT 100mm
(D) ASSY ENCODER (RDM-3020)
ITEM NO.| PART NO. DESCRIPTION NOTE 1 | RDM-2013 | ENCODER BRACKET 5 2 601-5410 GEAR 15, 66 ; @e
101 | 370-5043 OPT INC ENCODER 100PLS e5)) A
201 | 018-0001 SET SCR HEX SKT CP UNBR M3x4
@ ASSY MECHANISM (RDM~3100) (D-1/3)
ASSY MECHANISM (RDM-3100) (0-2/3)
ITEM NO, PART NO. DESCRIPTION NOTE
| 1 | YZ-3101 | MECHA BASE |
| 2 | YZ-3102 | SIDE PLATE |
| 3 | RDM-3101 | SIDE PLATE R |
| 4 | YZ-3103 | ADJUST SHAFT |
| 5 | GLC-3052 | MOVING PLATE |
| 6 | GLC-3053 | ACTUATER |
| 7 | YZ-3109 | SHAFT GUIDE |
| 8 | YZ~-3110 | DRIVEN PULLEY |
| 9 | RH-3311 | KEY |
| 10 | GLC-3054 | STOPPER SPACER |
| 1 | GLC-3055 | ADJUST RING |
| 12 | RH-3313 | BEARING SPACER |
| 13 | YZ-3116X | THRUST COLLAR |
| 101 | 100-5025 | BERING UNIT |
| 102 | 350-5081 | BALL SCREW R |
| 103 | 601-5472 | RUBBER STOPPER |
| 201 | 000—0412-FS | M SCR PH W/FS M4x12 |
| 202 | 000-0430 | M SCR PH M4x30 |
| 203 | 030-0520 | HEX BLT M5x20 |
| 204 | 030-0630 | HEX BLT M6x30 |
| 205 | 039-0013 | HEX BLT M10x40 |
| 206 | 039-0021 | HEX BLT M10x25 |
| 207 | 050-0010 | HEX NUT M10 |
L 208 059-0017 HEX NUT P=1.75 M12
ASSY MECHANISM (RDM-—3100) (D-3/3)
ITEM NO.| PART NO. DESCRIPTION NOTE 209 | 060-0004 FLT WSHR M4 210 | 060-0010 FLT WSHR M10 211 — | 061-0004 SPR WSHR M4 212 | 061-0006 SPR WSHR M6 213 | 061-0010 SPR WSHR M10 214 061-0012 SPR WSHR M12 215 | 069-0020 FLT WSHR Mi2 216 — | 061-0005 SPR WSHR M5 217 | 090-0012 SCREW LOCK 218 | 090-0013 GREASE
ASSY LIMIT SWITCH (RDM—3150) (D-1/2)
Ss) (RIGHT LiNT Sw) (LEFT LIMIT Sw)
Sb) vinit Swo Writ NC Merniwse.
(P) ASSY LIMIT SWITCH (RDM-3150) (D-2/2)
ITEM NO.| PART NO. DESCRIPTION NOTE
| 1 | | RDM-8151 | SWITCH BRACKET | Se |
| 1 | | KR-8023 | LIMIT SW NUT PLATE | Ba |
| 101 | 508-5199 | SW MICRO TYPE | |
| 102 | 509-5363 | MAG, LIMIT SW | & |
201 | 000-0430 M SCR PH M4x30 202 | 060-0004 FLT WSHR M4 203 | 061-0004 SPR WSHR M4
| 204 | 000—-0314—FS | M SCR PH W/FS M3x14 |
| 205 | 051-0003 | FLG NUT M3 |
301 SGB-4084—-25 | WIRE HARN LIMIT SW 211-5282-06RE | CONN PLUG 9090 06P--RE 211-5284 CONN PIN 9090 AWG 18-24
211-0167 TERM LUG RND ID5
| 302 | 601-0460 | PLASTIC TIE BELT 100mm |
| 303 | 280-0425 | CORD CLAMP 10¢ |
| 304 | 209-0023 | CONN CLOSED END |
@ ASSY CRANK (RDM-—3200) (D--1/2)
@Q ASSY CRANK (RDM-3200) (D-2/2)
| ITEM NO.| | PART NO. | DESCRIPTION | NOTE | |
| 1 | GLC-3131 | CRANK | B | |
| 2 | | GLC-3132 | JOINT SHAFT | ; ra | |
| 3 | GLC-3133 | J, SHAFT COLLAR | SC | |
| | | a | | RpM-s201 | PARALELL LOD | GC? |
| 5 | | GLC-3135 | GUIDE J. SHAFT | Zo | |
| 6 | GLC-3016 | ROD SCREW | oe | ||
| 7 | RDM-322 | | CON ROD | @ | ||
| 8 | RDM—3203 | NUT 18 L | ro) | ||
| 101 | 111-0010 | ROD END ¢10 | [ome | |
| 102 | 111-0018 | ROD END ¢18 | SS | ||
| 103 | | 111-0025 | ROD END 418 L | Se |
201 | 000-0512-FS | M SCR PH W/FS M5x12
| | | 202 | a50-0o10 | HEX NUT M10 |
203 | 059-0020 HEX NUT M18 (P=1.5)
| 204 | 060-0010 | FLT WSHR M10 |
205 | 061-0010 SPR WSHR M10 206 | 069-0084 SPR WSHR M18 207 | 090-0012 SCREW LOCK 208 | 090-0013 GREASE
@) ASSY AC UNIT (RDM-3300)
Z [0A] [HAN swt
Lake
- ASSY AC UNIT (RDM-3300) (D-2/2)
ITEM NO.| PART NO, DESCRIPTION NOTE
| 1 | | RDM-3301 | AC UNIT BRACKET | ER |
| 2 | RDM-3302 | COVER LID | Le | |
| 3 | | 421-6950 | STICKER MAIN SW | |
| 4 | | 421-6592 | STICKER ON-OFF |
5 421~-6595~08 | STICKER 10A
| 6 | | 421-6516 | STICKER EARTH |
101 | 280-0417 TERMINAL, BINDING POST, BLACK 102 | 509-5234 SW TOGGLE 25A 103 | 280~-5134~-6N34 | BUSHING STRAIN RELIEF 6N34 104 | 600-se43-25 | CABLE & PLUG ASSY W/-F- L=2.5M 105 | 210-5037 2P PHONO JACK 106 | 514-5030 FUSE HOLDER 107 | 514~5036-10000 | FUSE 6.4830 10000mA 125V
201 | 010-0306-F_~—| S~TITE SCR PH W/F Max6 202 | 008-0410 TMP PRF SCR TH M4x10
@ ASSY PWR SPLY (RDM-—4009) (D-1/2)
peoe
WIMLLLLLLL L, OO ® NMESELEL WEL Lod 2®
@ ASSY PWR SPLY (RDM—4000) (D~2/2)
ITEM NO.| PART NO. DESCRIPTION NOTE
| 1 | | RDM-4001 | WOODEN BASE A | | |
| 2 | RDM~4002 | FAN MOTOR BRACKET | : | |
| |} | 3 | | aa1-n40s | STICKER FUSE INSTR |
| 4 | | TX-4002 | GRIP | —] |
| 101 | | 601-6227-01_ | | PWR AMP W/SW REGU 12V 5A |
102 | 601-6228 PWR AMP FOR SUPER WOOFER
| | | 108 | se0-sias | PWR XFMR 90-240V 100V 2.5A 18.5V 7A | |
| 104 | | 400-5055 | SW REGU 90V~240V 5V 10A | | |
105 | 260-0035 FAN MOTOR AC100 (CONDENSER) / 106 | 270-5032 NOISE FILTER 20A
| 107 | | 400-5117¥ | DC MOTOR DRIVER |
| 108 | | 117-5167 | TERNINAL 5P-2Px2 SHORT |
| 109 | | 514-5028 | FU HLDR 1P W/COVER |
110 | 514-5037~4000 | FUSE 6,46x30 4000mA 250V
| U1 | | 270-5009 | LINE NOISE FILTER |
(D-1/2) 4100) @ ASSY DRIVE SPLY (RDM
oe aa NX A LALLEZ,
SLELEL LE, Zz
@3} ASSY DRIVE SPLY (RDM-—4100) (D-2/2)
ITEM NO. PART NO. DESCRIPTION NOTE
| 1 | RDM-—4101 | WOODEN BASE B |
| 2 | RDM-—O100 | ASSY SHIELD CASE |
| 3 | TX—4002 | GRIP. |
| 101 | 837-7753 | DRIVE BD |
102 117-5167 TERMINAL SP-2Px2 SHORT
201 005-3125 W SCR RH 3.1x25
202 005-3520 W SCR RH 3.5x20
204 005-3516 W SCR RH 3.5x16
206 000-0516-FS M SCR PH W/FS M5x16
207 006-3113 W SCR FH 3.1x13
301 600—6025-01 WIRE HARN FLAT 26P
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
PWR XFMR WIRING WIRE HARN COIN SW MARS
| SGB-4884-47 | QUATTRO BD | QUATTRO_8D | coIn | 560-5148 |
| cp | ce cal | METER | ||
| $12V_ 18> 18 | 185-118 | 18 | v7 | |
| SND oe | 5 an | su TS | moe ye) | oe |
al ON A cu-a fe ERIRY
| 0 | $ | A | ||||||
| Guo | ait Iso | bey = | JEU | aq f2tt | bat | att | |||
| VELLON | 2 | COIN SW | ist | 3 | sefzl | Braj | ||
| _ | +12 | N.C | fats | at | at) | | soli | |||
| cor, | ERP io tg —__—___"_ 19, " | — | te | ro | | vim] | ‘ia | rt | |
| TE METERT | oo, | 3 | g) cot MeTaR | : | fa | a | a | fa |
| (END CONNECTOR) eee ENTRY LAME | isc} | ari | is 5 | fst} |
=" wirie| ae ge
| 5 | Eau | ex | ||
| 18 | INTERFACE CABLE | rf | 7 | ; aoe |
1 Q4ARS COIN DOOR) COIN ENTRY LAMP Baus | | leat fy hagih teat
| jai | 21) | [2 | ||
| SGB—+084—~4745 SGB-4004—46 | MARS COIN CHUTE | aS | Er | 4 |
| i | Sit | Sit | ||
| ei! | lel | (el |
ae? | | a7? Gr MARS WIRING Bit) gis | Laut
| ists | 4 | iota |
| warts | wate | | ware |
8 TERM LUG 40K PC
| SGB-49084-48 | HANDLE MECHA BASE | i | 40k | = | aliaaiied |
COIN 3a5 +40) TERM LUG ROM—1 903
METER 40K ASSY MONITOR BASE
| RDM-1 208 | TERM LU sox | PS |
o———* Th ASSY ACCEL&BRAKE “Soo iogs—ssGaean - SGB-4084—-43 VIDEO ASSY SW UNIT
COIN CALCULATER,
asst
WHITE K 2 Cc oci2v
| Lamp
SENTINEL DOOR WIRING
| COCKPIT EARTH WIRING(RDM—1@@@) | soasfeiag | COIN CHUTE DOOR EARTH WIRING |
- WIRING DIAGRAM (D-2/2)
SEGA ENTERPRISES, LTD. No.2-12, Haneda 1—chome Ohta-ku, Tokyo 144, Japan Tel. : (03) 3743 —7438 OFAX : (03) 3743 — 5539 OTLX : J22357 SEGASTAR
© SEGA 1991
Printed in Japan