CATHODE RAY TOMES

Double Play

Double Play (Midway, 1977) · Document · 39 pages · 15 sections · original scan

Page 1

DOUPLE PLAY

INSTALLATION AND MAINTENANCE MANUAL

THE LELAND CORPORATATION

CINEMAT SYSTEM

1841 Friendship Drive

El Cajon, CA 92020-9981

Telex: CINTRON 4974293

FAX: 619-562-9468

Page 2

FCC WARNING

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.

It has been tested and found to comply with the limits for class A computing devices pursuant to subpart J of part 15 of FCC Rules, which are designed to provide! reasonable protection against such interference when operated in a commercial environment. / / Operation of this equipment in a residential area is likely to a cause interference in which cass the user at his own expense will be required to take whatever measures may be required to correct the interference.

POWER REQUIREMENT WARNING !

A power supply capable of supplying the following current (or greater) must be used for game conversion:

7 amps @ + 5.0 VDC lamp @ - 5.0 vDC 1 amp @ + 12.0 VDC

RECORD OF SERIAL NUMBERS

Record the game serial numbers and date purchased for future reference and/or game service.

Date purchased:

Main Circuit Board S/N:

Input/Output and Memory Expansion circuit board S/N:

Program part number (on EPROMs) :

Software serial number (on "attract mode" screen):

Page 3

TABLE OF CONTENTS

SECTION PAGE

WARRANTY 6

HINTS FOR SUCCESSFUL\ GAME INSTALLATION 7

  • Inspect Your Kit 8
  • The Old Case of the Bent Ic Pin 8
  • Attach the Ground 8
  • Which Pole is Which (Obsarving Polarity) ? 8
  • Marquee Blues (Marquee Installation) 10
  • Run Diagnostics (or Game Installaion 11 Success or Failure)
  • Monitor Outputs , 11
  • How Do I Turn Up the Sound ? 1i

GAME MODULE INSTALLATION 12

UNIVERSAL GAME CONVERSION 19

BOOKKEEPING/DIAGNOSTIC FUNCTIONS 22

  • Invoking Diagnostics 23
  • Selecting The Desired Function 23
  • Bookkeeping 24

a. Period and Dollar Counters 24

b. Setting Coins/Tokens per Dollar 24

Cc. Example of Setting Tokens 25 per Dollar

  • Diagnostics 26

a. Buttons And Controls Test 26

b. Processor Memory Test 27

c. Video Alignment Display 28 Anhalt

Page 4

TABLE OF CONTENTS, cont'd

SECTION

d. Video Memory Test

e. Viewing Background Screens and Background Test

  • Game Set Up

a. Coins per Credit / Credits per Coin,

b. Extra Play L

c. Attract Mode Sound

  • Game Play Statistics
  • Inning Duration Graphs
  • Erase All Player Statistics

SYSTEM TROUBLESHOOTING GUIDE

  • Input/Output Functions
  • Electronics
  • General Knowledge
  • Coin Counter Surge Protection Circuit

CONNECTOR PINOUT CHART

Page 5

TABLE OF CONTENTS, cont'd

LIST OF ILLUSTRATIONS

FIGURE

ody nw DESCRIPTION

AC/DC Power Connection

Marquee Installation

Main Circuit Board Assembly

Input/Output and Memory Expansion Circuit Board Assembly

Control Panel Bolt and Ground Braid

Piggy-back Circuit Board Mating

Control Panel Mounting and Cable Routing

Coin Counter Surge Protection Circuit

Page 6

A. WARRANTY

Seller warrants that its printed circuit boards, monitor and power supply, when furnished with the product and parts thereof are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller's warranty of above parts is subject to the normal use and service of its product. None of the seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, seller's sole liability shall be, as mutually agreed, to replace or repair such products which are returned to seller during said warranty period provided.

CONDITIONS:

a. Seller must be promptly notified in writing upon discovery by buyer that said products are defective. b. Products must be returned prepaid to seller plant. c. Seller's examination of said products discloses to seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

Seller is not responsible for bent pins on ICs not installed by seller's employees. In no event shall seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for this express warranty, seller disclaims all other warranties, expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and all other obligations or liabilities on seller's behalf, and it neither assumes nor authorizes any other person to assume for seller any other liabilities in connection with the sale of products manufactured by seller.

NOTICE REGARDING THE USE OF NON-SELLER REPLACEMENT PARTS:

Seller recommends the use of only seller's parts when replacing any malfunctioning component or assembly in the seller's system. For safety and reliability, seller does not recommend or authorize any substitute parts or modifications of seller's equipment. Such alterations may adversely affect game play, cause serious injury, and void your warranty. Unauthorized parts, modifications and non-seller's game conversion kits may also void FCC compliance.

To obtain repair, contact seller at 619-562-7000 between 8 AM and 5 PM Pacific Standard Time to obtain an RMA return authorization number. Affix this number to the outside of the shipping container when returning goods. Return to the above address.

Page 7

B. HINTS FOR SUCCESSFUL GAME INSTALLATION

Page 8

HINTS FOR SUCCESSFUL GAME INSTALLATION

Take some advice from the game masters. Successful game installation can be simple if you take a minute and read the following hints. It is worth it's weight in aspirin!

1. INSPECT YOUR KIT

Inspect all received parts for shipping damage and to familiarize yourself with the parts. Inspect all integrated circuits (hereafter called "Ic") for bent pins (being careful not to bend the pins).

THE OLD CASE OF THE BENT IC PIN

The #1 killer of a successful game installation, or for that matter, any other electronic device's proper operation, is bent pins. Avoid this plague and take the time (and patience) to make sure that all pins are in each hole and not bent.

Also, installing ICs with bent pins runs the risk of bending the pins even further and eventually breaking them.

If pins are bent, first, grip the group of pins lengthwise with long needle-nose pliers. This gripping action will straighten them in this direction. Next, if any pins are bent in the other direction, straighten each one individually with needle nose pliers being careful not to over-compensate. This overcompensation may break the pin.

ATTACH THE GROUND

Make sure to attach the ground braid to the control panel. Players risk an electric shock if the control panel is not properly grounded.

Refer to figure 5 for ground braid connection.

WHICH POLE IS WHICH (OBSERVING POLARITY)?

Electronic circuits are quite sensitive to polarity and can easily lose their sense of humor when the polarity is reversed. A fuse may not be all they blow! Experienced electronic engineers check the polarity two times before applying power! You should probably check it three times.

Refer to figure 1 on the next page for proper 115 VAC and DC power connections.

Page 9

FIG, AC/DC POWER CONNECTION

POWER CORD

BROWN

| CONTROL PANEL im -5y | YELLOW

= GND iE +12v [|__ORANGE

HOT

115 vac BLACK

E.M.I. FILTER GND >] BLacK |

BLACK

—-—____—_—6

GROUND BRAID D

NEUTRAL | A c

ORANGE

Ca) it

° a

° a DHDorwonan nan ° a

WJ INTERLOCK " SWITCH ") Noronwaa

RED

Nnoaoanrontrraca

N HOT FLUORESCENT AC GND AC

LIGHT FUSE WHITE GREEN | | YELLOW A, BLACK A.POWER SUPPLY BROWN +5V @ 7A ORANGE By @ In ORANGE (} () +12v @ 1A BROWN RED COIN DOOR LIGHTS B.I/0 MEMORY EXPANSION BOARD

RED BROWN C.MAIN LOGIC BOARD

-|—]- ISOLATION TRANSFORMER D.cIRCUIT PANEL PLATE

SEC PRI

MONITOR OUR PIN-OUT IS OPPOSITE OF THE PIN-OUT PRINTED ON THE CONNECTOR GROUND BRAID I.E. PIN 1 IS PIN 10 FOR A 10 PIN CONNECTOR

Page 10

MARQUEE BLUES (MARQUEE INSTALLATION)

Your game is a money making investment! Why compromise by installing a crooked marquee? Avoid this and follow these instructions for installing:

First, place the plexiglass on a table. Next, center the decal on the plexiglass, getting an idea of the general location (before peeling off the back). Now, carefully peel off the back and place the far edge (lengthwise) on the plexiglass first, centering the remaining un-stuck (important) decal. Finally, "roll" down the rest of the decal, slowly, squeezing the air bubbles out with your hand.

Pictured is the marquee on a Cinemat System Cabinet.

MARQUEE INSTALLATION

FIG. 2

Page 11

RUN DIAGNOSTICS (OR GAME INSTALLATION SUCCESS OR FAILURE)

Five minutes of diagnostics may save an hour of frustration wondering why a feature does not work. Our software department is the best in the business. They labored long and hard to write diagnostics to thoroughly check out your game. Take the time to follow the diagnostics section and prove to yourself that the entire game is working properly.

Next, play the game a couple of times to verify that all is well.

MONITOR OUTPUTS

The outputs from our system to the monitor are red, green and blue with negative horizontal and negative vertical sync. £

HOW DO I TURN UP THE SOUND ?

Volume adjustment is easy. Refer to figure 3 and locate VR1 (on main circuit board). Now look at the main board (largest board). Clockwise rotation increases the volume.

Page 12

C. GAME MODULE INSTALLATION

Page 13

Cc. GAME MODULE INSTALLATION

1. Parts for the DOUBLE PLAY game module are as follows. Please inspect and check off:

QTY DESCRIPTION

Manual, DOUBLE PLAY DOUBLE PLAY Marquee Lexan Decal Plexiglass Marquee Cinemat I/O Expansion Board EPROMs (Game Software) Custom Chip (U120) 02-14 Custom Chip Control Panel Assembly 1 1/2" Carriage Bolts #10 Flat Washers #10-24 Hex Nuts 410-24 Wingnuts 5/16"x 1" Spacers 6/32"x 1-1/2" Bolts 40 Pin Ribbon Interconnect Harness 10 Pin Power Interconnect Harness roy HPRUUNN AREER NMP REE

Install the 26 DOUBLE PLAY EPROMS in the main board noting the chip location ("U" number) printed on each chip and referring to Figure 3. Match the location of pin 1 of both the EPROM and socket, plug each EPROM into the socket indicated. Be sure all EPROMs' pins are aligned and the EPROMS are pressed firmly in place.

Install the custom chip U120 in the main logic board at location U120 and the 02-14 custom chip at U85 making sure Pin 1 of the chip and Pin 1 of the socket are aligned.

Recheck steps 2 and 3 for proper parts placement and orientation.

Remove the Z-80B microprocessor from location U99 of the main logic board and reinstall it at location U13 of the I/O and Memory Expansion board. Install the I/O and Memory Expansion board ribbon cables as shown in figure 6.

Position the DOUBLE PLAY control panel assembly on the cabinet and attach using the 1 1/2" carriage bolts, washers and 10-24 hex nuts provided. Install only the front-most bolt, washer, and nut on each side at this time. See figure 5.

Page 14

10. Route the control panel wiring harness. Locate the three connectors labeled P5, J4 and J5 at the end of the control panel harness. Plug connectors P5 into connector P5 located along the top edge of the main logic board. Similarly, plug J4 into J4 and J5 into J5 of the I/O and Memory Expansion board. Plug the remaining two wires (white and violet) of the control panel harness into connector P4 of the main board. Refer to Connector Pinout Chart in back of manual.

Attach the marquee to the plexiglass using the procedure in section B above.

Installation of the game module is now complete. We suggest you now use the system's "on board" diagnostics to inspect the game. See the diagnostics section of this manual.

After testing the cwntrol panel, use the remaining two carriage bolts, washers and wing nuts to secure the control panel.

Page 15

Fic. MAIN CIRCUIT BOARD ASSEMBLY

TO MONITOR

Pi 03-15006-VSN u8

DOUBLE PLAY

03-15005-VSN 03-15000-VSN SPI sar | b42

CINEMAT MAIN LOGIC

PRINTED CIRCUIT ASSEMBLY

COMPONENT SIDE

TYPICAL PIN 1 LOCATION qq He jp2

2? b40

O26 TO SPEAKER a es P3 & POWER VOLUM IN VRUO conteot RESET Swi Pay! U1IZO PS} |! TO CONTROL PANEL Pé6lq! Nor USED P4:COIN SW SERV SW 1 AND 2 PLAYER START

03-15018-VSN

Page 16

IdM 2@dM

pn SN 9N LN

en €n 2525C DOUBLE PLAY yaez= MEMORY AND I/O EXPANSION ge" 3 PRINTED CIRCUIT ASSEMBLY COMPONENT SIDE

Cc

nN 2 NOT USED

a alee c

o

Cc % ' n z L Cc a N > wor used | a W e 3

03-15027-VSN

03-15026-VSN u2 DOUBLE PLAY | 03-15025-VSN i Lee

TYPICAL PIN 1 2 | LOCATION Cc Cc ° 33> ZHo Hw co ts

? 15-01 : WO davod “StL OL S(~

or |] dasn LON

INPUT/OUTPUT AND MEMORY EXPANSION CIRCUIT BOARD ASSEMBLY FIG. 4 D1D0T NIVW 66N OL

Page 17

CONTROL PANEL BOLT AND GROUND BRAID

FIG. 5

Page 18

prow

© wi nnvva

Eom

Erm»

PIGGYBACK CIRCUIT BOARD MATING

FIG. 6

Page 19

D. UNIVERSAL GAME CONVERSION

Page 20

D. UNIVERSAL GAME CONVERSION

1. Parts for the DOUBLE PLAY conversion kit are as follows. Please inspect and check off:

QTY DESCRIPTION

Plexi, Marquee Decal, Marquee Ty-Wrap w/eyelet Control Panel Assembly, DOUBLE PLAY Circuit Board Assembly, DOUBLE PLAY Manual, DOUBLE PLAY Harness, Video Harness, Coin Service Harness, Speaker Decals, Cinemat DC Power Harness PNERRPRRPEERPE °

Remove existing game control panel, and all buttons or joystick controls associated with it. Position the universal control panel above the control panel intended for conversion. Feed the harness through a convenient hole large enough for the harness connectors. Refer to Figure 7.

Securely mount the universal control panel with a bolt or screw not easily removed from the exterior of the cabinet. Avoid pinching the wires. Secure using the ty-wraps included with your kit.

When routing the harness, leave enough slack so that servicing of the control panel and circuit board assembly can be accomplished with relative ease. Place a wire ty-wrap as close to the circuit board connectors as possible tc relieve strain on the connector pins.

Mount the circuit board in an area of the cabinet that receives ample ventilation. Make sure the circuit board can be removed easily for service.

Refer to the D.C. power wiring diagram, making all the power connections as shown. Be sure to hook up the ground braid. Also, observe proper polarity. Careful with this one!

The last order of business is the Marquee and Plexiglass. See section B above for this procedure.

The conversion process is now complete. It is recommended at this point, to go into diagnostics to test the performance of the new kit.

Page 21

a) f rs

CONTROL PANEL MOUNTING AND CABLE ROUTING

FIG. 7

Page 22

E. BOOKKEEPING / DIAGNOSTIC FUNCTIONS

Page 23

BOOKKEEPING / DIAGNOSTIC FUNCTIONS

DOUBLE PLAY has extensive bookkeeping and diagnostic functions. These functions are explained in the following sections:

1. INVOKING DIAGNOSTICS

With the game running in the attract mode follow these steps:

a. Press and hold the one-player start button while pressing and releasing the service button (found inside the coin door mounted to the top of the coin box). Concerning Kits, connect the appropriate pins to ground referring to the Connector Pinout Chart in the back of the manual.

b. Release the one-player start button.

Cc. The game screen should now appear as shown on the next page. Instructions for selecting and entering the listed functions are displayed at the top of the screen with the five selectable options below them. The game's software version number is shown in the lower left-hand corner of the screen.

SELECTING THE DESIRED FUNCTION

The one-player start button selects the desired function. The function has been selected when the display color for that particular function changes. Pressing the two player start button enters the selected function. Selecting the RESTART THE GAME function returns the game to normal operation.

An example of the display is as follows:

MAIN MENU

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

BOOKKEEPING DIAGNOSTICS GAME SET-UP GAME STATISTICS INNING DURATION GRAPHS ERASE ALL PLAYER STATISTICS

RESTART THE GAME

S/N: XXXXXXXX

Page 24

BOOKKEEPING

The bookkeeping screen is displayed when that option is selected and entered from the main menu. Five lifetime counters are shown. These counters are set to zero at the factory and are not resetable by the operator. These counters are:

COINS DROPPED MECH 1 - This counter shows the total number of coins that have dropped through the LEFT coin mech.

COINS DROPPED MECH 2 - This counter shows the total number of coins that have dropped through the RIGHT coin mech.

TOTAL COINS DROPPED - This is the total number of coins dropped through BOTH mechs.

SERVICE BUTTON PRESSED - The number of times that the service button has been pressed. Pressing the service button to enter the bookkeeping / diagnostic section does not affect this counter.

TOTAL CREDITS GIVEN - The total number of credits the game has given in it's lifetime is shown on this counter. (See the game setup section of this manual for information on setting the number of coins per credit).

a. PERIOD AND DOLLAR COUNTERS

Three resetable counters, located to the right of the lifetime counters are provided to aid the operator in tracking the games' cash intake over a period of time. These counters are:

  • coins dropped
  • dollars collected

As in the main menu, these options are selected by pressing the one-player start button and entered by pressing the player two start button. To reset the period and dollar counters for either coin mech, press the one-player start button until the message "RESET COIN MECH 1 (or 2) DOLLARS COLLECTED" changes color. Then press the two-player start button.

b. SETTING COINS/TOKENS PER DOLLAR

To calculate dollars collected, the bookkeeping system needs to know how many coins/tokens are required to make a dollar. Normally, this number

Page 25

would be 4 for quarter operation. If you operate a location where, for example, 6 tokens equal one dollar, then the dollar multiplier should be changed to 6 so that the dollars collected counters wili reflect accurately what the game has earned.

To change the coin "multiplier," use the one-player start button to highlight the COINS PER DOLLAR message for the desired coin mech then use the two-player start button to change the multiplier.

EXAMPLE OF SETTING TOKENS PER DOLLAR

An arcade giving 10 tokens per dollar should have the coins/tokens per dollar multipliers set as shown.

An example of the display is as follows:

10 COINS PER DOLLAR COIN MECH 1 10 COINS PER DOLLAR COIN MECH 2

NOTE: THE COINS PER DOLLAR MULTIPLIER DOES NOT AFFECT THE NUMBER OF COINS PER CREDIT OR CREDITS PER COIN. SEE THE GAME SET-UP SECTION OF THIS MANUAL FOR THAT INFORMATION.

BOOKKEEPING

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

LIFETIME PERIOD COINS COINS DOLLARS

COINS DROPPED - MECH 1ie)0$0.00
MECH 2ie)0$0.00
TOTAL COINS DROPPED00$0.00

SERVICE BUTTON PRESSED te} TOTAL CREDITS GIVEN 0

RESET COIN MECH 1 DOLLARS COLLECTED RESET COIN MECH 2 DOLLARS COLLECTED

SET COINS/TOKENS PER DOLLAR: 4 COINS PER DOLLAR COIN MECH 1 4 COINS PER DOLLAR COIN MECH 2

RETURN TO MAIN MENU

Page 26
  • DIAGNOSTICS

The diagnostic menu is displayed upon entering diagnostics from the main menu. The player can then select the desired function.

An example of the display is as follows:

DIAGNOSTICS

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

BUTTONS AND CONTROLS TEST PROCESSOR MEMORY TEST VIDEO ALIGNMENT SCREENS VIDEO MEMORY TEST VIEW BACKGROUND SCREENS

RETURN TO MAIN MENU

BUTTONS AND CONTROLS TEST

This test allows the operator to check the game controls and switches. Pressing a button or activating a control causes the description of that button or control to change color on the video screen.

The word GOOD will appear to the right of the control's description when the switch contacts close and will remain on the screen until the button is released.

Pressing the two-player start or service button twice will end the test and return you to the diagnostic menu.

An example of the display is as follows:

PRESS THE FOLLOWING BUTTONS:

1 PLAYER START 2 PLAYER START MECH 1 COIN BUTTON MECH 2 COIN BUTTON SERVICE SWITCH

GO BACK BUTTON EXTRA BASE BUTTON LEFT RUN/STEAL BUTTON RIGHT RUN/STEAL BUTTON RUN/CUTOFF BUTTON

Page 27

RUN/AIM BUTTON

BATTERS JOYSTICK HORIZONTAL: XxH XXXXXXXX bar graph XXXXXXXXXXXXXXXAXXXXXXXX

BATTERS JOYSTICK VERTICAL: xxH XXXXxKEXX bar graph XxXxXXXXXXXXXXXXXXXXXXXXXX

PITCHING JOYSTICK HORIZONTAL: xxH XXXXXXXX bar graph XXxXxXxXxXxXXXXXXXXXXXXXXXXXX

PITCHING JOYSTICK VERTICAL: XxXH XXXXXXXX bar graph xxXxXXXXXXXXXXXXXXXXXXXXXX

PRESS THE PLAYER 2 OR SERVICE SWITCH BUTTON TWICE TO EXIT

be PROCESSOR MEMORY TEST

The processor memory test checks all on-board RAM and EPROM memory with the exception of the video memory. The messages TESTING MASTER ROM, TESTING MASTER RAM, TESTING COLOR RAM and TESTING SLAVE MEMORY will each appear on the left side of the screen as each of those tests are performed. The result of each test (pass or fail) is displayed on right side of the screen next to the description of that test.

Two error messages may appear during slave memory test, these are COMMUNICATION ERROR and SLAVE NOT RESPONDING. ICs to be checked, in order of priority, are listed below:

COMMUNICATIN ERROR - a. U19 b. U21 through U23 c. U45 d. v60 e. U62 f. U64

SLAVE NOT RESPONDING ~ a. U10 (slave RAM) b. U3 (EPROM) c. Ul (280 CPU) d. U2 e. U20, U18 f. U61, U63

In the case of a failure of a ROM or RAM, the location (U number) of the suspected part is shown on the screen.

The following is an example of the display indicating a U107 failure.

Page 28

PROCESSOR MEMORY TEST

TESTING MASTER ROMMASTER ROMBAD

CHIP 107 SUSPECT

TESTING MASTER RAMMASTER RAMGOOD
TESTING COLOR RAMCOLOR RAMGOOD

TESTING SLAVE MEMORY SLAVE ROM

SLAVE RAM

PRESS 2-PLAYER START TO EXIT TESTING

VIDEO ALIGNMENT DISPLAY

Three video alignment screens are provided to aid in adjusting the game's video monitor for maximum picture quality. Refer to the video monitor technical manual (not supplied) for technical information and adjustment instructions.

The first screen consists of a white crosshatch Pattern. This should be used to adjust screen position, horizontal size, vertical size and focus. Pressing the two-player start button advances the display to the next alignment screen.

The second alignment screen is used to adjust the red and green intensity. An eight level (0-7) color scale is shown for each red and green. The monitor should be adjusted so that level zero is black and one through seven appear as seven distinct levels.

The third alignment screen shows a four level blue color scale. Adjust the blue intensity so that level zero is black and levels one through three show as three distinct shades of blue. Eight other colors are also displayed for reference, they are, from 0 through 7 respectively: blue, green, red, cyan, magenta, yellow, gray and white.

VIDEO MEMORY TEST

The video memory test checks the foreground video memory. The test appears as a series of colored bars moving across the screen. After each pass (about 5 seconds), the results of the test will be displayed on the screen.

Page 29

10. If the test was successful (all RAMs good), the message "VIDEO RAM CHECKS OK" will be displayed for about 1 second and the test will be repeated. Pressing the two-player start button anytime during the test will abort the test and return you to the diagnostic menu.

If the memory test fails, the message "VIDEO RAM TEST FAILED" will be displayed along with the location (U number) of the suspect RAM. In the event that the video error display is unreadable, a series of tones will also indicate the suspect chip (see table below).

NUMBER OF AUDIBLE BEEPS SUSPECT ICs

2 U35 and U36 4 U33 and U34 6 u48 and U49 8 U46 and U47

e. VIEWING BACKGROUND SCREENS AND BACKGROUND TEST

This test is set up to view all the background screens by pressing the one-player start button to advance the screens. Pressing the two-player Start button exits the program.

An example of the display is as follows:

BACKGROUND PROM TEST

PRESS 1-PLAYER START TO ADVANCE. OR PRESS 2-PLAYER START TO EXIT.

GAME SET-UP

The game option set-up section allows the operator to change various game options. As explained in previous sections, the one-player start button selects and highlights the desired function and the two-player start button enters or executes the function.

a. COINS PER CREDIT / CREDITS PER COIN

The coinage of each mech may be set to require multiple coins for each credit or give multiple credits for each coin.

To change coinage, follow the example screens below: (all examples assume 1 coin=25 cents)

Page 30

For 25 cent play: 1 COIN FOR 1 CREDIT

For 50 cent play: 2 COINS FOR 1 CREDIT

Two plays for 25 cents: 1 COIN FOR 2 CREDITS

EXTRA PLAY

An option is included to award an extra play for the insertion of multiple coins before the game is started.

For example, if the coinage is set as follows:

1 COIN FOR 1 CREDIT EXTRA PLAY FOR 2 CREDITS

then the result will be, 1 coin will give 1 credit and 2 coins will give 3 credits. Each additional coin will add one credit.

ATTRACT MODE SOUND

This option, when selected, enables the game sounds during the attract mode.

An example of the display is as follows:

GAME SET-UP

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TwO PLAYER START BUTTON

COIN MECH 1 1 COIN FOR 1 CREDIT NO EXTRA PLAY

COIN MECH 2 1 COIN FOR 1 CREDIT NO EXTRA PLAY

TWO PLAYER INNING FOR 1 CREDIT _ NO ATTRACT MODE SOUND YES

RETURN TO MAIN MENU

Page 31
  • GAME STATISTICS

Game statistics are provided to aid the operator in setting up his game for maximum profit.

The operator may reset the game statistic counters by selecting the "reset game statistics" function.

An example of the display is as follows:

GAME STATISTICS

SELECT FUNCTION WITH 1-PLAYER START BUTTON ENTER FUNCTION WITH 2-PLAYER START BUTTON

NUMBER OF 1-PLAYER INNINGS: 0 PLAYER WINS: 0 COMPUTER WINS: 0

NUMBER OF 2-PLAYER INNINGS: fe) COMPLETE GAMES BOUGHT: Q

RESET GAME STATISTICS

RETURN TO MAIN MENU

  • INNING DURATION GRAPHS

Graphs are provided which indicate the duration of one and two player innings. Average play time is also displayed. These graphs may be reset by selecting the reset options located at the bottom of the screen.

An example of the display is as follows:

INNING DURATION GRAPHS

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

ONE PLAYER INNINGS: AVERAGE TIME: 0:00

xxxx bar graphs follow xxx 1:00- 0 1:31-3:00 3:01-5:00 5:01-10:90 10:01-15:00 15:01-20:00 20:01-25:00 25:01-30:00 30:01-UP CoOS8D000000

Page 32

TWO PLAYER INNINGS: AVERAGE TIME: 0:00

13. 2:00-1:00

3:01-5:00 5:01-10:00 10:01-15:00 15:01-20:00 20:01-25:00 25:01-30:00 30:01-UP “xxx bar graphs follow xxx 1-3:00 e00000000

RESET 1-PLAYER INNINGS AND BAR GRAPHS RESET 2-PLAYER INNINGS AND BAR GRAPHS RETURN TO MAIN MENU

ERASE ALL PLAYER STATISTICS

DOUBLE PLAY will store player statistics for 300 players in battery backed-up memory. To clear these statistics select the ERASE ALL PLAYER STATISTICS option from the menu shown below. Similarly the top player lists may be erased by selecting that option.

An example of the display is as follows:

ERASE ALL PLAYER STATISTICS

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

ERASE ALL STATS ON EXIT? NO ERASE TOP PLAYER LISTS ON EXIT? NO

RETURN TO MAIN MENU

D. SYSTEM TROUBLESHOOTING GUIDE

The entire Cinemat game system can be broken down into major groups. A brief quide to troubleshooting each section follows:

1. Input/Output functions:

a. Monitor

  • No raster (i.e. black screen)

a. Check AC supply to monitor. If there is no power at the monitor, trace the

Page 33

wiring back to the isolation transformer and/or verify that power is reaching the transformer.

b. Check monitor fuses.

Display scrolls (apparent syncronization problem).

a. Check monitor alignment adjustments.

b. Check RGB and syncronization signals on PCB connector and trace through to the monitor.

Black screen

a. Check for +5.0 VDC at circuit boards.

b. Check connectors are securely seated and in the proper position.

White or checkerboard screen.

a. Check for +5.0 VDC on P4 - 3 through 7. If any of these signals are low, replace uil4 (74LS08). If this fails, replace U119 (74LS257).

b. Check the clock signal on the master 280 (U99-6), DOUBLE PLAY I/o and Memory Expansion Board (U13), REDLINE RACER Sound Board (U14).

c. Check reset on the 280 (U99-26). This signal should normally be high and go low when the reset button is pressed.

White or red vertical lines close together on entire screen or half of screen.

a. Check video RAMs U33 through U36 and U46 through U49. Refer to sheet il and 18 on schematic.

Vertical lines on playing field (background).

a. Check signals on U81 through U83 (74LS166's).

b. Regarding other background problems, check the position of JP2 Jumpers, swap US6, (74LS461) with U60, see if problem disappears.

White vertical bars, usually on half of screen

Page 34

sometimes with an audio buzz.

a. Caused by excessive temperature. Swap U45 with U23 and/or U60 with U22 (74LS461's).

  • Intermittent flashing video or color changes.

a. Check for +5.0 VDC at circuit boards. TP1 and TP2 (+5 VDC)

  • Picture freezes.

a. Check for +5.0 VDC at circuit boards. TP1 and TP2 (+5 VDC)

b. Check 280s (U1 and U99). They should be Zilog Mostek devices with a "B" suffix (6 MHz). If not call for replacement.

c. Check for damaged sockets on master EPROMs and master CPU.

  • Drifting pattern (any color).

a. Check connector and signals:on Pl.

b. Sign of synchronization problems. Check DCLK.

c. Check U40 (RGSO9), U42 (RGSO7), and U43 (RGS08).

b. Buttons, joysticks and coin counters.

  • A careful visual inspection of the buttons, harnesses and connectors is advised.

a. Inspect harness crimps.

b. Check for broken wires.

c. Check for broken solder joints at the termination point.

26 Trace signals through back to the input IC on the PCB.

  • Electronics

a. Main board electronics.

i. Problems can sometimes be traced to a bad CPU or crystal. Check the master and slave CPU's and their associated components.

  • Check EPROMs for background and foreground display and the associated video timing logic.
Page 35
  • Check power at the ICs.

Add on board(s) that control game specific functions.

  • Again, check for functions specific to the board.
  • Check all ICs for proper socket installation.

c. Check power at the ICs.

General Knowledge

a. Proper voltage input jumpering on the board is critical! Follow the instructions on this carefully. A symptom of improper jumpering is an audio buzz or no audio. Check for 12.0 to 15.0 VDC at U122-5 (audio amp). Refer to Power Supply Modification section of manual. NOTE: If your speaker is not connected, you will not hear any sound! Seriously, try adjusting the audio volume control pot (VP1). See section B above on adjusting the volume.

b. Game powers up with garbage on the screen - no buttons function - audio may buzz

  • Remove P4 and P5 and reset system (push button on main board). If picture appears, the problem may be a stuck coin switch, button or bad harness or ground connection.
  • Visually inspect connector crimps and wire colors.
  • Check for + 5.0 VDC at board.

c. A word about coin counters:

Do not use mechanical coin counters in any kit or dedicated game. These devices produce an inductive "kick" that will damage components on the circuit board(s). Problems caused by this are checkerboard video. A quick check to see if this is your problem is look at the "NMI not" signal on both Z80s (pin 17). If a low output is observed, try replacing U114 (74LS08) or if needed, U119 (74LS157).

The bookkeeping on our games is very accurate and includes number of coins dropped and dollars earned.

If you must install a coin counter, the next page shows a simple hookup using diode protection.

Page 36

COIN COUNTER SURGE PROTECTION CIRCUIT FIG. &

  • IF YOU MUST INSTALL A COIN COUNTER

COIN SWITCH

COIN COUNTER

Pha OR PL-7 +5V

DIODE MAY BE 1N4001 THROUGH 1N4003

Page 37

, ROUBLE PLAY, CONNECTOR PINOUT CHART

FROM TO

CONNECTOR SIGNALCONNECTORWIRE

PIN #

MAIN LOGIC BOARD CONNECTORS:

Pl-1 NOT USED «Ble =HSYNC. ___GRay

:P1-3MONITOR, -V_SYNC__—WHITE
—Pin4._____._ MONTTOR,GROUND.—=__BLACK._
P1-5MONITOR, REDa __RED

B1=6 POLARIZING KEY

P1-7MONITOR,GREENGREEN

P1-8 NOT USED - ,

_P1-9. MONT TOR, BLUEiBLUE

P1-10 NOT USED

P2-1SPEAKER GROUNDSPEAKER.Gray

eo P3-1 5 VOLTS. ad 221

“i P3-2+5 VOLTS |~J2=2._—-
1.373+5 VOLTSJ2-3)

3-4 POLARIZING KEY (OPTIONAL) J2-4

-—P3=5GROUND.-1225—
P3-6GROUND32-6
P3-7GROUND32-7
P3-8GROUND32-8

P3-9 32-9

P3-10+12 OR 25 VOLTSJ2-10

P4-1 NOT USED

P4-2 GND , COIN, SERVICE COIN DOOR BLACK OR GREEN

P4-3TWO PLAYER STARTCONTROL PANELVIOLET
P4-4NORMALLY OPENCOIN SWITCH 2ORANGE
P4-5NORMALLY OPENSERVICE SWITCHYELLOW
P4-6ONE PLAYER STARTCONTROL PANELWHITE
P4-7NORMALLY OPENCOIN SWITCH 1BLUE

P4-8 NOT USED P4-9 NOT USED P4-10 NOT USED

P5S-1 NOT USED

P5-2 GROUND CONTROL PANEL GREEN

P5-3GO BACK (N.O.)CONTROL PANELGRAY
P5-4RUN/CUTOFF (N.O.)CONTROL PANELBROWN
P5-5EXTRA BASE (N.O.)CONTROL PANELBLUE
P5-6RUN/AIM (N.O.)CONTROL PANELYELLOW
P5-7RUN/STEAL OUTER (N.O.)CONTROL PANELORANGE

P5-8 NOT USED

P5-9RUN/STEAL INNER (N.O.)CONTROL PANELRED

P5-10

P6 NOT USED XXXXXXXXXXXXXXXXXXXXXAXXXXKXKXKXXXKKXXXXXXXXXXXXXXXXXKXXXXKKXXKXKKX INPUT/OUTPUT AND MEMORY EXPANSION BOARD CONNECTORS:

Page 38

DOUBLE PLAY, CONNECTOR PINOUT CHART

FROM CONNECTOR SIGNAL PIN # DESCRIPTION

+5 VOLTS +5 VOLTS +5 VOLTS POLARIZING KEY GROUND GROUND GROUND GROUND NOT USED +12 OR +25 VOLTS

+5 VOLTS +5 VOLTS +5 VOLTS POLARIZING KEY GROUND GROUND GROUND GROUND

+12 OR +25 VOLTS

NOT USED

GROUND +12 VOLTS +12 VOLTS NOT USED SWING UP-DOWN NOT USED BALL SPEED NOT USED NOT USED CURVE POLARIZING KEY GROUND

GROUND DATA LINE 13 +5 VOLTS CLOCK RES 3 RES 2 DATA LINE 12 DATA LINE 3 DATA LINE 2 POLARIZING KEY SPARE NOT USED TO CONNECTOR PIN #

POWER SUPPLY POWER SUPPLY POWER SUPPLY

POWER SUPPLY POWER SUPPLY POWER SUPPLY POWER SUPPLY

POWER SUPPLY

P3-1 (MAIN P3-2 LOGIC P3-3 BOARD) P3-4 P3-5 P3-6 P3-7 » P3-8 P3-9 P3-10

BATTERS JOYSTICK BATTERS JOYSTICK PITCHERS JOYSTICK

BATTERS JOYSTICK BATTERS JOYSTICK

PITCHERS JOYSTICK

PITCHERS JOYSTICK

PITCHERS JOYSTICK

TAG PCB J1-2 TAG PCB J1-7 TAG PCB J1-1 TAG PCB J1-5 TAG PCB J1-4 TAG PCB J1-3 TAG PCB J1-6 TAG PCB J1-10 TAG PCB J1-9

TAG PCB J1-8 GREEN ORANGE ORANGE

YELLOW BROWN

VIOLET

BLUE

GREEN

GREEN BROWN RED BLACK VIOLET ORANGE GRAY YELLOW BLUE

WHITE

Page 39

DOUBLE PLAY, CONNECTOR PINOUT CHART

FROMTO:
CONNECTOR SIGNALCONNECTORWIRE
PINDESCRIPTIONPIN #COLOR

J6 NOT USED XXXXXXXXXXXXXXXXXXXXXXXKKKXXXXKKKXXXXKKXXXXXXKXKXXXXKXKXKAKXXAXKXK INPUT/OUTPUT AND MEMORY EXPANSION BOARD 40 PIN RIBBON CABLE CONNECTOR:

JTA-1MASTER ADDRESS LINE 11u99-1 (MAIN
JTA-2MASTER ADDRESS LINE 12U99-2 LOGIC
J7A-3MASTER ADDRESS LINE 13U99~3 BOARD)
J7A-4MASTER ADDRESS LINE 14ug99-4
J7A-5MASTER ADDRESS LINE 15u99=5
J7A-6CLOCKU99-6i
J7A-7MASTER DATA LINE 4U99-7;
J7A~8MASTER DATA LINE 3u99-8
I7A-9MASTER DATA LINE 5U99-9
J7A-10MASTER DATA LINE 6u99-10
J7A-11+5 VOLTSu99-11
J7A-12MASTER DATA LINE 2u99-12
J7A-13MASTER DATA LINE 7U99-13
J7A-14MASTER DATA LINE 0uU99-14
J7A-15MASTER DATA LINE 1ug99-15
J7A-16INTU99-16
J7A-17MNMIu99-17
J7A-18NOT USEDu99-18
JTA-19MREQu99-19
J7A-20I/O REQuU99~-20
J7A-21RDu99-21
J7A-22WR99-22
J7A-23NOT USEDU99-23
J7A~24WAITug99-24
J7A-25+5 VOLTSu99-25
J7A-26PORU99~26
J7A-27M1U99-27
J7A-28RFSHu99-28
J7A-29GROUNDU99-29
J7A-30MASTER ADDRESS LINE 0U99-30
J7A-31MASTER. ADDRESS LINE 1U99-31
S7A-32MASTER ADDRESS LINE 2U99-32
J7A-33MASTER ADDRESS LINE 3U99-33
J7A-34MASTER ADDRESS LINE 4U99-34
J7A-35MASTER ADDRESS LINE 5u99-35
J7A~36MASTER ADDRESS LINE 6U99-36
JTA-37MASTER ADDRESS LINE 7U99-37
J7A-38MASTER .ADDRESS LINE 8U99-38
JTA-39MASTER ADDRESS LINE 9u99-39
J7A-40MASTER ADDRESS LINE 10u99-40

J73B NOT USED