CATHODE RAY TOMES

Pole Position TM-218 1st Printing

Pole Position (World) (Namco, 1982) · Technical Manual · 88 pages · 71 sections · original scan

Page 1

Operation, Maintenance, and Service Manual

Complete with Schematics and Illustrated Parts Lists

Page 2

\f reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O, Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) From California, Alaska, or Hawaii Ss (408) 745-2900 Service from anywhere in the area shown in white @ oltre (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ‘ae From New Jersey (201) 469-5993 From anywhere else in this area toll-free (800) 526-3849

EUROPE

Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND @ 06252155

Page 3

Operation, Maintenance, and Service Manual

Complete with Schematics

and Illustrated Parts Lists

*Pole Position is engineered and designed by Namco Ltd. Manufactured under license by Atari, (nc.

Page 4

Pole Position

© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penaities for violating federal copyright laws. Courts can impound infringing articles while egal action is pending. If infringers are convicted, courts can order de- Struction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have io pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Lithographed in the U.S.A. vil

Page 5

Pole Position

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

@ substitute non-ATARI paris in the game © modify or alter any circuits in the game by using kits or parts not supplied by Atari.

to licensed communications services is not permitted by the Federal Communications Commission (FCC). \f you suspect interference from an ATARI® game at your location, check the following: © all green ground wires in the game are properly connected as shown in the the game wiring diagram @ the power cord is properly plugged into a grounded 3-wire outlet @ the game PCB is properly installed within the Electromagnetic Interference (EMI) cage @ the EMI Shield PCB is properly installed and in series with the game PCB harness. Refer to Figure 3-15 to make sure that the game PCB and the Shield PCB are correctly installed. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover for service in your area. {

Page 6

Pole Position

Table of Contents

Set-Up Procedures A. New Features 1-4 B. Inspecting the Game 14 C. Leveling the Sit-Down Cabinet . 15 D. Space and Power Requirements . 1-5

  • Installation Requirements... 15
  • Selecting the Voltage Plug 15 E. Locating the Switches ... 1-6
  • Power On/Off Switch 16
  • Utility Panel Switches 1-7
  • Option Switches ...... 1-7
  • Memory Back-Up Jumper . 1-7 F. Setting the Option Switches .. 1-7 G. Performing the Initial Self-Test . 1-10 H. Game Play.............- 412
  • Attract Mode 1-12
  • Play Mode .... 1-12
  • High-Score Mode . 4:13
  • Hints for Game Play. ....... 1-13

Self-Test Procedure A. Comments on Troubleshooting .. 2-2 B. Performing the Self-Test 22

Maintenance, Repair, and Parts A. Cabinet-Mounted Assemblies 3-2 B. PlayerControls ..............200-0006 3-7 C. Fluorescent Tube and Speaker Replacement 3-16 D. Video Display. ........... cece eee eee 3-20 E. Utility Panel . 322 F. Coin Doors ......... 3-24 G. Printed-Circuit Boards . «. 3:30 H. PowerSupply Assembly. .........- 000s eee cee eee eee ee 351

Glossary of Terms |. «20.020... 0. 0c cece eee eee GLA

Page 7

Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4

Figure 1-5 Figure 2-1 Figure 2-2 . Figure 2-3 Figure 2-4

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4

Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8

Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12

Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16

Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20 Figure 3-21

Table 1-1 Table 1-2 Table 1-3 Table 1-4

Table 2-1 Table 2-2 Table 2-3 Pole Position

List of Illustrations

Game Overview, Upright Cabinet ......... 20.2.0... e eee eee 1-2 Game Overview, Sit-Down Cabinet . 1-3 Leveling the Sit-Down Cabinet . . 4-5 Location of Game Switches... 16

Self-Test Display... 0.0.0.0... cece cece eee eee ee 4-11 Self-Test Screen 1: Upright Test Passes 2:3 Self-Test Screen 1: Sit-Down Test Passes . 23 Self-Test Screen 1: Test Fails ........ - 23 Self-Test Screen 2... 0... cece cect eee en eee eee 2-4

IMustrated Parts Lists

Cabinet-Mounted Assemblies, Upright Cabinet .............. 3-2 Cabinet-Mounted Assemblies, Sit-Down Cabinet . 3-4 Control Panel ........... 37 Control Pane! Assembly . 38 Steering-Wheel Control Assembly .............. 0s eee eee 3-10 Gear-Shifter Control Assembly. . . Foot-Pedal Control Assembly Fluorescent Tube and Speaker Board Removal, Upright Cabinet 3-16

Fluorescent Tube and Speaker Board Assembly Upright Cabinet 3-17 Sit-Down Cabinet Speaker Removal 3-18 Video Display ................ . 3-21 Utility Panel Assembly vee 322

Vertically Mounted Coin Door American-Made Coin Door : Removing the Printed-Circuit Boards ................ Central Processing Unit Printed-Circuit Board Assembly 3-24 3-27 3-30

Pole Position Video Printed-Circuit Board Assembly .......... Regulator/Audio lt PCB Assembly, U.S.-Built Cabinet . Regulator/Audio Il PCB Assembly, lreland-Built Cabinet | EMI Shield PCB Assembly. . Power Supply Assembly .

List of Tables

Switch Settings for Game and Price Options ...............+ 18 Switch Settings for Game and Play Options . 1-9 Self-Test Procedure ................ 1-10 Qualifying Lap Information ............. 00. eee ce eee 1-13

Locating Failed Components on the Video PCB ... 2-2 Locating Failed Components on the CPU PCB . 2-2 Locating the Failed RAM... ....... 0... cee c eee cence eee 24

Page 8

Pole Position

vi

NOTICE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide teasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.

Page 9

Set-Up Procedures

How to Use this Manual

This manual, written for game operators and service technicians, describes the Pole Position game. The manual contains information about the Upright and Sit-Down Pole Position cabinets. Whenever information is unique to the Upright

cabinet, this symbol appears: i

Whenever information is unique to the Sit-Down

cabinet, this symbol appears: r 3)

Wherever information is unique to /re/and-Built

games, this symbol appears: *

ZEIGA —<Spris Sees os UZ S Wis | y TV nf Pras 1 fs

V2 Chapter 1 describes new features, gare setup, settings of option switches, self-test procedures, and game play. Chapter 2 contains self-test procedures. Chapter 3 details maintenance, repair, and parts information. A glossary of terms is in the back of this manual for your convenience. in addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the Upright game cabinet; Figures 1-2 and 3-2 illustrate the Sit-Down game cabinet. italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

=A

Chapter

Page 10

Set-Up Procedures

ATTRACTION PANEL, FLUORESCENT TUBE

+ VIDEO DISPLAY See Figure 3-11 aN STEERING-WHEEL CONTROL ASSY. See Figure 35

UTILITY PANEL: See Figure 3-12

COIN DOOR See Figures 3-13 & 3-14

x Items with a serial number label 07 U.S.-Built cabinets AND SPEAKER See Figure 3-8 or 3-8

DASHBOARD ‘See Figure 3-1

EMI CAGE See Figure 3-1 & 3:20

GEAR-SHIFTER CONTROL ASSY. See Figure 3-6

CAPACITOR See Figure 3-21

CONTROL PANEL See Figures 3-3 & 3-4

SPEAKER See Figure 3-9

FOOT-PEDAL ASSY. -e See Figure 37 POWER SUPPLY See Figure 3-27 Pole Position

% GAME IDENTIFICATION LABEL (Serial number appears here on Ireland-Built games)

WARNING

SHOCK HAZARD

  • GAME PCBs See Figures 3-15, 3-16, 8 3-17

+ REGULATOR! AUDIO tt PCBs See Figures 3-15, 3-18, & 3-19

POWER ON/OFF SWITCH

This game should only be connected to a grounded 3-wire outlet. If you have only a 2wire outiet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!

Figure 1-1 Game Overview

Upright Cabinet

Page 11

Pole Position Set-Up Procedures

+ GAME IDENTIFICATION LABEL (Serial number appears here on Ireland-Built games)

  • GAME PCBs “> UTILITY PANEL ASSY, See Figures 3-15, 3-16, & 3-17 See Figure 3-12 SPEAKER EM! CAGE See Figure 3-10 See Figures 3-15 & 3-20 “> ATTRACTION PANEL See Figure 32

ACCESS PANEL

  • REGULATOR/ AUDIO II PCBs See Figures 3-15, 3-18, & 3-19

POWER ON/OFF SWITCH POWER SUPPLY CAPACITOR See Figure 3-21 See Figure 3-21

  • VIDEO DISPLAY | See Figure 3-11

STEERING-WHEEL CONTROL ASSY. See Figure 35

GEAR SHIFTER CONTROL ASSY. See Figure 3-6

CONTROL PANEL See Figures 3:3 & 34

ON COIN DOOR

See Figures 3-13 & 3-14

WARNING ACCELERATOR AND BRAKE

SHOCK HAZARD See Figure 3-7 .))

This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded! Items with a serial number label on U.S.-Built cabinets

Figure 1-2 Game Overview Sit-Down Cabinet

Page 12

Set-Up Procedures

A. New Features

The Pole Position game has many new features. Even if you are familiar with ATARI® games, you should note these important differences: @ Electromagnetic Interference (EMI) Cage in U.S-Built Cabinets Only. Games built after December 1, 1982, will have the CPU and Video printed-circuit boards (PCBs) mounted inside this cage. The EMI cage reduces interference from the game to television and radio receivers. See Figure 3-15 for details. American-Made Coin Door. Your game may be equipped with a new coin door. This door is very similar to the vertically mounted coin door, but does not have lockout coils. When ordering parts for your coin door, please check coin door illustrations in Figures 3-13 and 3-14 carefully to make sure you are ordering the correct part number. Steering-Wheel Control. This steering wheel is designed to provide a more realistic response from the race car on the display. Foot-Pedal Control (Accelerator and/or Brake). These pedals have been redesigned to accommodate a snap-action switch for the brake anda potentiometer, turned by a spring and cable, for the accelerator. Metal Attraction Panel on Sit-Down Game Cabinet. The metal attraction panel mounted on top of the cabinet entices players with its Formula-1 racing graphics. Quadraphonic Sound in Sit-Down Cabinet. Four 4-ohm, 6-ounce, high-fidelity speakers (two under the control panel; two behind the seat) surround the player with the exciting and realistic sounds of Gran Prix racing. New features and other major parts of the game are shown in Figures 1-1 and 1-2. Throughout this manual, wherever a new feature is mentioned, you will see this symbol: .

1-4 Pole Position

B. Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition.

1.

WARNING To avoid electrical shock, do not plug in the game until the procedures in Sections B, C, and D have been completed!

Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits are firmly plugged into their sockets on the printed-circuit boards (PCBs). c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. d. Note the game serial number printed on a label on the back of the cabinet. Verify that the same serial number is also on the Pole Position game PCBs, Regulator/Audio II PCBs, power supply, and video display. See Figures 1-1 and 1-2 for locations of the serialnumbered components. Please mention the serial number whenever you call your distributor for service. e. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure they are mounted securely.

WARNING

To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!

Page 13

Pole Position

  • For the Sit-Down cabinet, remove the metal attraction panel from the protective wrapping. Remove the three button-head screws and retainer on the front window. Place the attraction panel over the mounting holes. Reinstall the retainer and screws.

C. Leveling the Sit-

C. Leveling the Sit Down Cabinet

The Sit-Down cabinet rolls easily from location to location on 4-inch casters. To level the cabinet, lift the game up on one side. Place a block of wood, a book, or another object (that is at least 2-inches thick) under the raised cabinet. Partially unscrew the adjustable glides (see Figure 7-3) until they extend below the caster. Lower the game and lift it up on the other side; partially unscrew the adjustable glides. Lower the game. To prevent players from moving the game around, be sure to adjust all four glides.

CASTER

ADJUSTABLE GLIDE a

Figure 1-3 Leveling the Sit-Down Cabinet ‘Set-Up Procedures

D. Space and Power Requirements

  • Installation Requirements

Power 250 W Temperature 0° to +38°C(+ 32° to + 100°F) Humidity Not over 95% relative Upright Cabinet 62 x 90 cm (25% x 354 in.) 186 cm (72% in.) Sit-Down Cabinet 165 x 64 cm (65 x 25% in.) 194 cm (76 in.) Space Required Game Height

Space Required Game Height

  • Selecting the Voltage Plug
WARNING SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!

The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voltage. Next, check the wire color on the voltageselecion plug that is plugged into the game’s power supply. Make sure the voltage-selection plug is correct for the voltage of your location (see Figure 3-21). Now, plug the game into a grounded 3-wire outlet.

Page 14

‘Set-Up Procedures

E. Locating the Switches

CAUTION

Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls, Pole Position

  • Power On/Off Switch

The power on/off switch is located on the back of the Upright cabinet on the lower left side. On the Sit- Down cabinet the power on/off switch is located on the lower left side of the cabinet (see Figure 1-4).

OPTION SWITCHES SWITCH AT QJA (Game and price) SWITCH AT 9L (Game and play)

information.

JUMPER AT 6B (Memory back-up) See CO-218-01 for NAMCO PCB UTILITY PANEL ASSY. See Figure 3-12

POWER ON/OFF SWITCH

Figure 1-4 Location of Game Switches

1-6

Page 15

Pole Position

  • Utility Panel Switches The volume control(s), self-test switch, coin counter(s), and auxiliary coin switch are located on the utility panel in both the Upright and Sit-Down cabinets (see Figure 3-12). The utility panel is located inside the upper coin door. The volume control{s) adjust the level of sound produced by the game. The Sit-Down cabinet has four volume controls: one for each speaker. The Upright cabinet has two volume controls: one for each speaker. The self-test switch is used to enter and exit the Self-Test Mode. The coin counter(s) record the number of coins entered into the game. The auxiliary coin switch is used to credit the game without activating the coin counter(s).
  • Option Switches Option switches are located on the game CPU PCB (see Figure 1-4). Refer to supplement CO-218-01 for switch locations if your game has NAMCO PCBs.

a. Game and price options are at CPU PCB location QUA. b. Game and play options are at CPU PCB location 9L.

  • Memory Back-Up Jumper The memory back-up jumper is at CPU PCB location 6B. Position this jumper to the on setting. The memory back-up jumper is positioned on the off setting when shipped from the factory to prevent jeakage and to provide longer life for the battery at location 6A on the CPU PCB. The jumper must be positioned to the on setting so that the battery can provide power to the CMOS memory. This memory Stores the high-score table and operator statistics. Set-Up Procedures

The jumper does not affect game play. We recommend you position this jumper to the off setting when you expect extended downtime.

F. Setting the Option Switches

Settings of the game option switches are explained in Tables 1-1 and 1-2. Options preset at the factory are shown by the < symbols. However, you may change the settings according to your individual needs. To verify option-switch settings, first set the power on/off switch to the off position and then to the on position. Next, set the self-test switch to the on position. Compare the information on the screen to the option switch settings listed in the tables in this section. Then set the self-test switch to the off position. Table 1-1 describes the switch settings for options relating to game price, coin mechanism multipliers, number of laps per game, and number of seconds per lap. These switches are on the game CPU PCB at location WA. The multipliers (QJA switches 1-5) determine the value of the coin mechanisms to the game’s logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. The mechanism either accepts or rejects the coin. The coin door has two coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1.

Page 16

‘Set-Up Procedures Pole Position

NOTE
CoinOptionInterconnect Assembly

J55A-P55A permits a coin placed in either coin mechanism to register in the same coin counter. The cable connector is located between the coin door harness and the main harness (see the Coin Op-

tionInterconnectWiringDiagramin
SP-218). Whenitisused,left coin

mechanism option switches at 9JA apply to both coin mechanisms. If you want different options for the left and right coin mechanisms, remove Coin

OptionInterconnectAssemblyJ55A-

PSSA and connect J55 directly to P55. If you have NAMCO game PCBs, refer to CO-218-01 for the location of the option switches.

Table 1-1 Switch Settings for Game and Price Options

Settings of 8- Toggle Switch on Pole Position CPU PCB (at 9JA)

876521
4aOption

On 4 racing laps * Off 3 racing laps <

OffOff90 seconds per lap <
OffOn100 seconds per lap
OnOff110 seconds per lap
OnOn120 seconds per lap *

Right Coin Mechanism

OffOff1 coin for 1 credit <
OffOn2 coins for 1 credit *
OnOff3 coins for 2 credits
OnOn4 coins for 3 credits

Left Coin Mechanism

OffOffOff1 coin for 1 credit <
OffOffOn1 coin for 2 credits
OffOnOff1 coin for 3 credits

Off On = On 2 coins for 1 credit + On Off = On 3 coins for 2 credits

OnOfOff3 coins for 1 credit
OnOnOff4 coins for 3 credits
OnonOnFree Play

“4Manufacturer's recommended settings for Upright cabinet

  • Manufacturer's recommended settings for Sit-Down cabinet

1-8

Page 17

Pole Position

NOTE

We recommend that game difficulty for the race laps (EXTENDED RANK) and the qualifying lap (PRACTICE RANK) be increased periodically. These changes will ensure that Pole Position continues to offer maximum excitement and challenge. Except in locations with extremely skillful and advanced players, these settings should not be increased more than one level per month. Set-Up Procedures

Table 1-2 details option-switch settings for the Attract Mode sound, kilometers or miles per hour, and difficulty in race laps and qualifying laps. The switches are on the game CPU PCB at location 9L. Pole Position leaves the factory with option switches set at the manufacturer's recommended difficulty level. The game will be exciting and challenging for piayers at these settings.

Table 1-2 Switch Settings for Game and Play Options

Refer to CO-218-01 for switch locations if your game is equipped with NAMCO PCBs.

Settings of 8-Toggle Switch on Pole Position CPU PCB (at 91)

87654321

Option

Off On

Off On

Off Off Off Off On Off Off On On

OffOffon

On Off Ott

On Off On

OnOnOff
OnOnOn

Off Off

Off On Off On

On Off On Otf On On on On Attract Mode sound off Attract Mode sound on «4

Kilometers per hour Miles per hour <

Difficulty in Race Laps Easiest lap <

Most difficult lap

Difficulty in Qualifying Lap Easiest lap

<

Most difficult lap

‘“4Manufacturer's recommended settings

1-9

Page 18

Set-Up Procedures

G. Performing the Initial Self-Test

This game will test itself and provide data to show that the game’s circuitry and controts are operating properly. The data is provided on the video display and speakers. No additional equipment is necessary. Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you switch to self-test.

Refer to Figure 1-4 for the location of the option switches and Figure 3-12 for the location of the selftest switch. Set the self-test switch to the on position to see the Self-Test Display in the Self-Test Mode (see Figure 1-5). To exit the Self-Test Mode, set the self-test switch to the off position. Pole Position

The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure. \f a part of the test described in Table 1-3 fails, refer to Chapter 2. We suggest you perform the self-test procedure when you first set up the game, when you collect money from the game, when you change game options, or when you suspect game failure.

CAUTION

Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.

Table 1-3 Self-Test Procedure

Instruction Test Passes

1, Without touching the pedal(s), Set the self-test switch to the on position. Ali credits wil! be cancelled.

  • Press down on the accelerator pedal.
  • Press down on the brake pedal of the Sit-Down cabinet.
  • Turn the steering wheel clockwise, then counterclockwise.
  • Shift the gear shifter.
  • Shift the gear shift, press the auxiliary coin switch, and activate the coin switches.
  • Press the auxiliary coin switch.
  • To end the tesi, switch the self-test switch to off. Random symbols are displayed on the screen for about five seconds. The self-tesi display appears. RAMs and ROMs are tested, If the screen is different from the self-tesi display, or if there are sounds, refer to Chapter 2, Self-Test Procedure.

The numbers to the right of ACCEL increase from 00 to somewhere between 90 and AQ as you press down on the pedal. If the test fails refer to Chapter 2. The numbers to the right of BRAKE switch from 00 to FF. For the Upright cabinet, the numbers to the right of BRAKE should always read 00. If the test fails, refer to Chapter 2.

Rotating the whee! clockwise causes the numbers to the right of STEER- ING to increase. Rotating the wheel counterclockwise causes the numbers to decrease. !f the test fails refer to Chapter 2. The words to the right of SH/F T change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, refer to Chapter 2. The numbers to the right of SOUND increase from 00 to 20, and a new sound is played with each number. Test all 20 sounds. If the test fails, reter to Chapter 2.

Game statistics appear (for a few seconds) at the bottom of the screen. Press the coin switch each time you want to see the statistics. To erase game statistics, simultaneously press down on the accelerator pedal and press the auxiliary coin switch twice. Statistics will be reset at /999!. To reset the high-score table, simultaneously press down on the accelerator pedal and change gear shifter from low to high. The high-score table will be reset and contain fictitious scores.

1-10

Page 19

Pole Position Set-Up Procedures

ALL RAMS GOOD ALL ROMS GOOD ACCELERATOR PEDAL a is / BRAKE PEDAL

EL 00. STEERING —____,

WHEEL STEERING 00

SOUNDS a LEFT COIN

SOUND MECHANISM

COINI RIGHT COIN COIN2 1 MECHANISM

QUALIFYING is

LAP TIME TIME NO. OF LAPS

GOAL: IN THE RACE

RAGE DIFFICULTY LEVEL, 2

PRACTICE. (See Table 1-2)

AUTO STAR

999. 999, 3 999. __ GAME STATISTICS 999. 999,

GAME AUTOMATICALLY STARTS* (When correct number of

Coins are inserted) THE COUNT STARTS AT 999(999)

AND DECREASES. For example, if you play 10 games, the game subtracts 10 from 99.9, and the display shows 98.9 for the number of games played. (Disregard decimal points.)

NO. OF GAMES PLAYED NO. OF POINTS SCORED (x10) NO. OF SECONOS PLAYED NOT APPLICABLE

999. 999, 999, 999. 999, 999, !

NO. OF SECONDS THAT GAME \ HAS BEEN POWERED ON NO. OF GAMES IN WHICH NO. OF GAMES IN WHICH PLAYER REACHED FINISH LINE PLAYER HAS QUALIFIED NO. OF GAMES THAT REACHED NO. OF GAMES THAT REACHED THIRD EXTENDED LAP FIRST EXTENDED LAP “if screen displays MANUAL START, Suspect the game harness. NO. OF GAMES THAT REACHED Refer to the Schematic Package. SECOND EXTENDED LAP

Figure 1-5 Self-Test Display

Page 20

Set-Up Procedures

H. Game Play

Pole Position is a one-player game using a color raster-scan video display. The game action takes place at Fuji Speedway in Japan. The country around the speedway consists of green meadows, hills, and snow-capped Mt. Fuji. The player drives a Formula-1 race car on the Fuji Speedway. Player controls consist of a steering wheel, a two-position gear shifter, and accelerator and brake pedals on the Sit-Down cabinet (accelerator only on the Upright cabinet). The object of the game is to finish the qualifying lap as quickly as possible. If the player beats the clock, he qualifies for the Gran Prix at Fuji Speedway, if not, he drives out the remainder of his time along the qualifying course. As a qualifier, the driver is ranked according to his qualifying lap time, from position one (the pole position) to position eight. The player then races against the clock and other cars to finish the four laps (operator-selectable option) of the race as fast as possible and to achieve the highest score possible. The player earns points for passing cars, driving on the track, and finishing the race with time remaining. He is rewarded with an extended-play lap for completing a lap. Pole Position has four modes of operation: Attract, Play, High-Score, and Self-Test. Self-Test is a special mode for checking the game switches and computer functions. You may enter the Self-Test Mode from any other mode. However, all credits will be cancelled.

1412 Pole Position

  • Attract Mode

The Attract Mode begins when you set the power on/off switch to on or after the Play, High-Score, or Self-Test Modes. The Attract Mode ends when the correct amount of credit for a game is inserted or when the Self-Test Mode begins. When the Attract Mode begins, the game displays apicture with the words POLE POSITION flashing at the top of the screen. A map of Fuji Speedway is displayed in the center of the screen. Within the map are the words FUJ} SPEEDWAY and 1 LAP 3459M. At the bottom of the screen is the copyright message. Then, the Attract Mode simulates game play. Eight cars are at the starting line. The player’s car, located in the eighth position, flashes on the screen. The starting lights flash from red to green and the race starts. The race continues until the player's car crashes into another car and explodes into a red ball of fire. Then, the car reappears on the screen and continues down the track until it hits a sign along the side of the road. Again, the car explodes. During this sequence, the message GAME OVER appears in the center of the screen. Finally, the Attract Mode displays the High-Score Table. The fastest lap time, average game speed, and prize winners appear at the top of the screen. Below this information is a list of the six highest scores. Opposite each score are the initials of the player who achieved that score.

  • Play Mode The Play Mode begins when the correct amount of credit for a game is recorded. The game starts with the player's car behind the starting line and 90 seconds on the clock. (See Section E to select a different clock setting.) The car must finish the qualifying lap within 73 seconds to be in the race. If the player does not qualify, his car continues on the track until 90 seconds are used up.
Page 21

Pole Position Set-Up Procedures

O 3. High-Score Mode

The High-Score Mode begins when a player has earned one of the 300 highest scores. The player has

— one minute to record his initials. A player rotates the

steering wheel to locate his initial. He presses a foot pedal to put his initial on the screen. The third time he presses the pedal his initials are transferred into the high-score table.

  • Hints for Game Play
  • Avoid puddles and the sides of the track because these slow you down. Accelerate and stay ahead of other racers. Stick to the inside of the track to make the corners. hes . Successful completion of a turn depends on brak- Table 1-4 Qualifying Lap Information ing skill.
  • When sliding, steer into the skid.

POSITION QUALIFYING LAP TIME* BONUS POINTS

158” 504000
269" 002000
362" 001400
464” 001000
566" 00800
668" 00600
770" 00400
873” 00200

“In seconds and hundredths of a second

Just before the race begins, the player's car (flashing on the screen) is placed at the starting line with seven other cars. The position of the car depends on the qualifying time as shown in Table 1-4. The starting lights flash from red to green, and the race begins. Racing hazards are other racing cars, sharp turns, and road signs. As the race progresses, more cars appear on the track. If the driver's car hits another car or a road sign, the driver's car is destroyed in an explosion. The driver's car reappears in a few seconds and the race continues. Driving through wet puddles or off the track slows down the driver's car. Racing into the first turn, the driver must tet up on the accelerator slightly to make the corner. Road signs flash along the side of the track. Depending on how well the player manipulates the controls, he can either roar through the hairpin turns like a champion or spin out in a flaming crash. He jockeys for position with the other racers, while keeping his eye ‘on the clock at the top of the screen. When his time runs out, the race is over. The top score achieved by a player appears at the top of the screen. The time alloted for the lap is displayed under the top score. Increasing lap time (in seconds and hundredths of a second) and the speed of the car appears last.

1-13

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

Self-Test Procedure

NOTE

The reference designators for components in this chapter refer to games with Atari® PCBs. If you have Namco Q PCBs, please refer to CO-218-01.

The following self-test procedures should be performed by a qualified electronic technician. This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you find the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is working properly.

LA we ; Eas

Chapter

Page 24

Self-Test Procedure

A. Comments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio !i printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you do not find a harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn't, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting a PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Tables 2-1 and 2-2 are troubleshooting aids, which can be used to locate faulty components.

Table 2-1 Locating Failed Components on the Video PCB Pole Position

Table 2-2 Locating Failed Components on the CPU PCB

Custom AtoD

Symptom Area PROM 1C RAM Converter

Audio Voice 9c 9D Screech/Crash 9E Player's Motor 12E,12F All Other Sounds 7L,11D 7K,7d Inputs. Brake and/or Accelerator 8

Steering 9K

Option Switches 9K,9M All Other Inputs 9M Control for Audio & Inputs 8H,9H Sync 7M High Scores 7E

Symptom Area PROM Custom RAM ic Large Car Pictures 12,13 Large Sign Pictures 12K,13K,12L, 13L. Small Cars & Signs 12N,13N All Cars & Signs 12H,11N 48H 9F,10F Alphanumerics 7N,8M 8N Raceway 2L,2M,2N,4L 3N

Background 6N.5K

Raceway & Background SL6L Middle & Sides of Raceway 28,2C,2D All Video 4D,7E,2F Red NE Green 1D Blue 11

2-2

B. Performing the Self-Test

This game will test itself and provide data to show that the game’s circuitry and controls are operating Properly. The data is provided on the video display and speaker. No additional equipment is necessary. Video game repair shouid only be performed by a qualified electronic technician. To begin the Self-Test Mode, set the self-test switch, which is located on the utility panel, to the on position.

CAUTION

Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and in- Correct action of the player controls.

Page 25

Pole Position Self-Test Procedure

SELF-TEST SCREEN 1—Test Passes: SELF-TEST SCREEN 1—Test Fails: Upright Cabinet. If the test passes, the screen If the test fails, the screen may display the picture displays the picture in Figure 2-1, Upright Test in Figure 2-3, Test Fails. Passes. See Chapier 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.

Figure 2-3 Self-Test Screen 1: Test Fails

Figure 2-1 Self-Test Screen 1: nom failure is indicated by the word ROM and a . pair of alphanumeric characters displayed at the top Upright Test Passes bf the screen.

Sit-Down Cabinet. if the test passes, the screen displays the picture in Figure 2-2, Sit-Down Test oe Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this pic- oO ture. To see self-test screen two, set the self-test switch to off and immediately back to on. Z

EXTENDED PRACTICE. RANK C AUTO START .

Figure 2-2 Self-Test Screen 1: Sit-Down Test Passes

Page 26

Self-Test Procedure

RAM failure is indicated by the word RAM anda pair of alphanumeric characters displayed at the top of the screen. Table 2-3 lists the failed RAM chip, the printed-circuit board (PCB) the chip is on, and the chip’s location. Replace the failed RAM, and restart the test (set the self-test switch to off, and then to on).

NOTE The reference designators for components in this chapter refer to games with Atari® PCBs. If you have Namco PCBs, please refer to CO-218-01.

Table 2-3 Locating the Failed RAM

Falled PCB Screen Display RAM Location

VideoRAM 0aF

Video RAM 1 7F

Video RAM 2 8H

Video RAM 3 7H CPU RAM 8 7E

cpuRAM 67
cpuRAM 77K

Video RAM 22 a

Video RAM 23 ral

Video RAM 26 8k

VideoRAM 277K
VideoRAM 283F
VideoRAM 29AF
VideoRAM 303
VideoRAM 314e

Steering failure is indicated by failure of the numbers to the right of STEERING to properly increase or decrease. As you rotate the wheel clockwise, these numbers should increase; as you rotate the wheel counterclockwise, they should decrease. If the test fails, suspect the Coupler PCB.

Accelerator failure is indicated by failure of the numbers to the right of ACCEL to increase as you press down on the pedal. If no numbers appear, suspect a bad A-D converter on the CPU PCB ora mechanical problem on the foot pedal assembly. Troubleshoot using the information in Chapter 3, Section 8, and the game schematics. Poie Position

Brake failure on the Sit-Down cabinet is indicated by failure of the numbers to the right of BRAKE to change as you press down on the brake pedal. On the Upright cabinet, brake failure is indicated by anything other than 00 appearing to the right of BRAKE. If the test fails, suspect a bad switch, improper mechanical adjustment on the foot pedal assembly, or no ground on the brake edge-connector pin in the harness. Gear-shifter failure is indicated by failure of the words to the right of SH/FT to change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, suspect loose connector wires or a bad switch. Sound failure is indicated by the absence of any sound when the coin switches or gear shifterare activated. Suspect a loose harness or connector wire, the volume control turned off, the custom audio I/O chip, or the Regulator/Audio || board. Troubleshoot using the game schematics. To see self-test screen two, set the self-test switch to off and immediately back to on.

SELF-TEST SCREEN 2: A white crosshatch pattern appears on the screen (see Figure 2-4). Use this pattern for convergence (see the raster-scan video display manual).

Figure 2-4 Self-Test Screen 2

Page 27

Maintenance, Repair, and Parts

This chapter details maintenance and repair information and provides information you need to order parts for your game. Common hardware (screws, nuts, washers, bolts, etc.) has been deleted from most of the parts lists. However, a parts list for the hardware to mount the printed circuit boards (PCBs) to the cabinet has been included. The printed circuit board (PCB) parts lists are arranged in alphabetical order by component. Each component subsection is sorted by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598-through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter

Page 28

Maintenance, Repair, and Parts Pole Position

A. Cabinet-Mounted Assemblies Manuals, Schematics, & Self-Test Label— See parts list on next page

Fluorescent Tube and Speaker See Figures 3-8 & 3.9 03733201 (Ventilation grille)

78-6900402 (Tape)

039371-01 (Shield retainer)

039417-01 4038881.01 (Display shield) (Lock)

Video Display See Figure 3-11 039376-01 5 j (Access panel)

Vix.=gA037701-01

78-6900402, = = (EMI Cage) (Tape) See Figures 3-15 & 320 ~< 4 Game PCB Assy. = B A039420-01 See Figures 3-15, (Dashboardidecal) 9-16, & 3-17 ‘Steering-Wheel © Control Assy. Gear-Shifter Control Assy. (A039459-01

See Figure 3-5See Figure 3-6(Main harn. assy.)

A039499-01 178034-024 Control Pane! Assy. ,

(Mone, —|See Figures 3-3 & 3-4{Main harn. assy.)

148001-001 .

Utility Panelcosasareirs 7
See Figure 3-1203914401See Figures

An (Speaker gtlle) e 318 & 3-19 Coin Door Assy. —~178048-001

See Figures‘A039460-01(Caster)

313 & 3-14 (Power harn. assy.) 038870-01 Power Supply e (Coin box enclosure—A i A037453-04

(Coin box encios sueSee Figure 321(Power cord)

03809101 A037454-04

(Coin box—not shown)‘x930353.01 i(Power cord)

178034-025 (abnet ase) A037470-01 (T-Molding) A039353-02 (On/off switch assy) (Cabinet assy.) 78-3201 (Glide) Foot-Pedal Assy. See Figure 3-7 (On/ott switch cover)

Figure 3-1 Cabinet-Mounted Assemblies

U.S.-Built Upright CabinetA039352-01A
lreland-Built Upright CabinetA039352-02A

3-2

Page 29

Pole Position Maintenance, Repair, and Parts

Cabinet-Mounted Assemblies Upright Cabinet Parts List

Assemblies and components in the following parts list are shown in Figure 3-1,

Part No. Description For U.S-Buili Upright Cabinet A037453.04 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference Cage (includes guides) A039353-01 Cabinet Assembly (inc/udes glides and PCB retainers, but not the rear access panel) A039459-01 Main Harness Assembly (for U.S. PCB) For treland-Built Upright Cabinet A037454-04 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, /taly, Netherlands, Norway, Spain, Sweden, and Uruguay) A039353-02 Cabinet Assembly (inciudes glides and PCB retainers, but not the rear access panel) A039499-01 Main Harness Assembly (for NAMCO PCB) For U.S-Built and Ireland-Built Cabinets A037470-01 Power On/Off Switch/Mounting Plate Assembly A037619-xx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001 A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039420-01 Dashboard Housing and Decal Assembly A039460-01 Power Harness Assembly A039576-01 Coin Option Interconnect Assembly (not shown) The following nine items are technical information suppiements to this game: CO-218-01 Pole Position Supplement (for NAMCO game PCB removal) SP-218 Pole Position Schematic Package (for Atari? game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-01 Pole Position Labei with Self-Test Procedure and Option Switch Settings (for Atari? PCBs) or $7-219.01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for NAMCO PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual! for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 14-Inch Wide x Inch Thick (96 inches required; used on top and bottom of attraction panel, on top edge of video display shield, and on top edge of contro! panel) 009992-01 On/Off Switch Cover 037332-01 Ventilation Grille 038091-01 Molded Coin Box (not shown) 038770-01 Metal Coin Box Enclosure (not shown) Acceptable substitute is part no. 038781-01 039144-01 Speaker Grilie 039371-01 Video Display Shield Retainer 039376-01 Rear Access Panel (does not include lock) 039417-01 Video Display Shield with Graphics 148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (/ocated on front panel) 178034024 ¥%-Anch Black Plastic TMolding (/ocated on side panels) 178034-025 y.-Inch Black Plastic Molding (located on front panel) 178048-001 2-Inch Rigid Caster

Page 30

Maintenance, Repair, and Parts Pole Position

A038465-01 A030101-01 (Main harn. assy), (Cabinet assy.) A039245-01 A039101-02 (Main harn. assy.) (Cabinet assy.) Game PCB Assy. —— See Figures 3-15, 3-16, & 3-17

037990-01 (Vent. Grille}

(Speaker) 178034-034 (T-Moiding) 039145-01 4037701-01 (Speaker grille)

‘igures i 039144-01 3-15 & 3:20 ‘Gille) 038641-01 148001-001 (vent a i (Speaker) 03a88101— 2 & (Lock) 178034-024 (T-Molding)

Utility Panel See Figure 3-12

Regulator/Audio Il PCB Assy. See Figures 3-18 & 3-19

Power Supply Assy. 035851-01 See Figure 3-21 (Hinge) A039246-01

(Power ham. assy) ‘A037470-01 A037453-03 (On/off switch assy.) (Power cord) 009992-01 A037454-03 (Ontoff switch cover) (Power cord)

Figure 3-2 Cabinet-Mounted Assemblies U.S.-Built Sit-Down Cabinet A039100-01 A Ireland-Built Sit-Down Cabinet A039100-02 A

Page 31

Pols Position Maintenance, Repair, and Parts

Manuals, Schematics, & Self-Test Label— See parts list on next page

039155-03 Gear-Shitter Control Assy. (Metal attraction panel) See Figure 3-6

a Video Display See Figure 311 Steering-Wheel Control Assy. See Figure 35 037086-01 (Front window retainer)

03914101 (Front window)

039148-01 (Display shield/graphics) Control Panel Assy. See Figures 3:3 & 3-4

ae

Coin Door Assy. See Figure 3-13 & 3-14 Foot-Pedal Assy. 038870-01 See Figure 3-7 (Coin box exclosure)

178023-001 (Caster)

(Glide)

Figure 3-2 Cabinet-Mounted Assemblies, continued U.S.-Built Sit-Down Cabinet A039100-01 A lreland-Built Sit-Down Cabinet A039100-02 A

Page 32

Maintenance, Repair, and Parts Pole Position

Cabinet-Mounted Assemblies Sit-Down Cabinet Parts List Assemblies and components in the following parts list are shown in Figure 3.2.

Part No. Description For U.S-Built Cabinet A037453-03 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) A039101-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039465-01 Main Harness Assembly For Ireland-Built Cabinet A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039101-02 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039245-01 Main Harness Assembly (for NAMCO PCBs) For U.S-Built and Ireland-Built Cabinets A037619-xx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001 A039246-01 Power Harness Assembly A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 The following nine items are technical information supplements to this game: CO-218-01 Pole Position Supplement (for NAMCO game PCB removal) SP-218 Pole Position Schematic Package (for Atari® game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-02 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari® PCBs) or ST-219-02 Pole Position Label with Self-Test Procedure and Option Switch Setting (for NAMCO PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055} TM-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Singie-Coated Adhesive Tape, %4-Inch Wide x inch Thick (72 inches required; used on top and bottom of front window, and on control panel) 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, 2-Inch Wide x Inch Thick (24 inches required; used in top slot of video display cleat) 002728-01 Control-Pane! Mounting Bracket 009992-01 On/Off Switch Cover 035851-01 Top Panel Hinge 037086-01 Front Window Retainer 037990-01 Ventilation Grill (on rear access panel) 038091-01 Molded Coin Box (not shown) 038641-01 Ventilation Grille (on rear access panel) 038870-01 Metal Coin Box Enclosure Acceptable substitute is part no. 038781-01 039141-01 Front Window 039144-01 Speaker Grille (located behind seat) 039145-01 Speaker Grille (located under control panel) 039148-01 Video Display Shield with Graphics 039155-03 Metal Attraction Panel with Graphics 148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (not shown—located behind seat) 148001-013 6- x 9-Inch Oval, 4-Ohm, 15 W Shielded High-Fidelity Speaker (located under control panel) 176015-110 #10 x %Inch Cross-Recessed, Pan-Head Tapping Screw (not shown—for mounting Speakers/grilles to seat back) 178034-024 %-Inch Black Plastic T-Molding 178034-034 1-Inch Black Plastic T-Molding (located on seat back) 178023-001 4-Inch Rigid Caster

Page 33

Pole Position

B. Player Controls

WARNING Before you remove or repair any control on the control panel, turn the game off.
CAUTION Before removing the final wing nut on the Sif- Down cabinet, hold the gear-shifter housing with one hand to prevent the front-heavy control panel from failing forward.

Control Panel Maintenance, Repair, and Parts

Opening the Control Panel:

  • Unlock and open the rear access panel (see Figure 3-3). Reach through the opening to the top of the control panel.
  • Remove the four wing nuts and washers that secure the contro! panel to the Upright cabinet. Two wing nuts and washers secure the control panel to the Sit- Down cabinet.
  • Guide or pull the control panel forward to its resting position. The steering wheel and gear shifter are now accessible for maintenance or repair (see Figure 3-4). Make sure the foam tape is in good condition. This tape is on the control panel of the Upright cabinet, and on the display shield for the Sit-Down cabinet.
  • Reassemble in reverse order.

Figure 3-3 Control Panel

3-7

Page 34

Maintenance, Repair, and Parts Pole Position

72-JB3814S “a crew) Players may receive an electrical shock if this ; control panel is not properly grounded! After ‘ servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal tab on the inside of the contro\ panel. ~~178002008 1 (Washer) J

A000608-09 Gear-Shifter Control Assy. See Figure 36

15-945S (Hex locknut).

(Spacer)

i sentun// (Control panel/decal) 039373-01 (Control panel) 1 75.035S 039409-04 Ff (Washer) (Decal) A039108-01 (Control panel/decal) 039143-01 (Control panel) 039132-01 039153-04 een (Decal)

~ 005255-04 SN (Bezel)

75-5112B E (Carriage bolt) ;

N\ A039229-01 ‘Steering-Wheel Control Assy. See Figure 3-5 ~ 75-5524B (Carriage bolt)

Figure 3-4 Control Panel Assembly Upright Cabinet A03941201 B Sit-Down Cabinet A039107-01 A

Page 35

Pole Position Maintenance, Repair, and Parts

Control Panel Assembly Parts List

Assemblies and cornponents in the following parts list are shown in Figure 3-4.

Part No. Description Upright Cabinet A039411-01 Control Panel with Decal (consists of contro! pane} 039373-01 and decal 039409-04) 75-5524B #%-20 x 1.50-Inch Carriage Bolt 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x }-Inch Thick (not shown) Sit-Down Cabinet A039108-01 Control Panel with Decal (consists of contro! pane! 039143-01 and decai 039153-04) 75-035S Y%-Inch Wide Flat Washer 75-5124B #%4-20 x 1.50-Inch Carriage Bolt 03913201 Control Panel Spacer Upright and Sit-Down Cabinets A039229-01 Steering-Wheel Control Assembly A000608-09 Gear-Shifter Control Assembly 72-JB3814S #8-16 x .87-Inch Screw 75-9458 #%4-20 Hex Locknut 75-5112B #%-20 x .75-Inch Black Carriage Bolt 005255-04 Shifter Bezel 03915401 Shifter Spacer 175002-004 #10 Flat Washer

Page 36

Maintenance, Repair, and Parts

039243-01 (Label) Pole Position

178099-003 (Steering wheel)

039230-01 (Steering cap)

039231-01 (Shaft)

178012.002 (Retaining ring) 039234-01 a (Steering frame) 72-HB3606S (Hex screw) ee

'A035220-02 178100-001 (Coupler POB assy.) a (Flange bearing) 178097-001 > (Bearing) oe 175003-002 (Nylon washer) i 178012-001 039233-01 ES (Retaining ring) (Encoder shaft)» «rp (GB

178101-002 175002-001 (Washer)

178101-001 (Gear) (Gear)

175002-002 (Heavy washer) 039232.01 (Spacer) 75-040 i (Washer) 035938-01 (Encoding wheel) 72-8008 75-07014 Gerew 75-044 (Washer) (Splitock washer) 72-8408 | (Screw) ———, ‘See text for lubrication information.

Figure 3-5 Steering-Wheel Control Assembly A039229-01 C

3-10

Page 37

Pole Position Maintenance, Repair, and Parts

WARNING wrench. Use an Allen wrench to remove the cap screw, . encoding wheel, washers, spacer, and bearing. To Before you remove or repair any player control, remove the encoder shaft, pry off the retaining ring. turn the game off.
  • To remove the steering wheel, hold the steering wheel shaft in a fixed position. Remove the cap screw, Removing the Coupler PCB, Encoding Wheel, washers, and gear. Pry off the retaining ring and and Steering Wheel: remove the heavy washer.
  • Reassemble in reverse order.
  • Open the control panel (see Figure 3-3). To remove the steering-wheel contro! assembly, 5 disconnect the green Groced wire from the grounding Lubricating the Steering-Wheel Control: hardware. Remove the hardware which secures the The two gears and the encoder shaft of the steeringsteering-wheel control assembly to the control panel wheel control assembly (see Figure 3-5) should be (see Figure 3-4). lubricated every six months. The bronze bearings of the
  • Unplug the harness connector on the Coupler PCB. steering shaft should be lubricated as needed. To lubricate these subassemblies, first open the control panel (see
  • To remove the Coupler PCB, remove the hardware Figure 3-3). Apply a light film of Nyogel 779 to the two securing the PCB to the steering frame. gears, encoder shaft, and both sides of both nylon wash-
  • To remove the encoding-wheel assembly, hold the ers. If necessary, apply a light-duty oll, such as 3-in-One oil, shaft of the encoding wheel in a fixed position with a to the bronze bearings.

Steering-Wheel Control Assembly Parts List

Assemblies and components listed in the following parts list are shown in Figure 3-5.

Part No. Description A035220-02 Coupler Printed-Circuit Board Assembly (includes Radial Optical Coupler) 72-8008 #10-32 x 0.50-Inch Steel Socket-Head Cap Screw 72-8012 #10-32 x 0.75-Inch Steel Socket-Head Cap Screw 72-8408 #4-40 x 0.50-Inch Steel Socket-Head Cap Screw 72-HB3606S, #6-32 x 0.38-Inch Zinc-Plated Steel Hex Washer-Head Screw 75-040 #10 Split-Lock Washer 75-044 #4 Split-Lock Washer 75-07014 #4 Flat Washer 79-58356 4-Position Connector with Locking Ramp (located on the Coupler PCB Assembly) 030369-01 Radial Optical Coupler (located on the Coupler PCB Assembly) 035221-01 100 2, +5%, %4W Resistor (located on the Coupler PCB Assembly) 039230-01 Steering Cap 039231-01 Steering Shaft 039232-01 Spacer 039233-01 Encoder Shaft 039234-01 Steering Frame 039243-01 Steering Cap Label 035938-01 Encoding Wheel 107013-001 3-in-One® Oil 175002-001 Flat Washer 175002-002 #10 Heavy Flat Washer 175003-002 Nylon Flat Washer 178012-001 Retaining Ring for 0.75-Inch Shaft 178012-002 Retaining Ring for 0.25-Inch Shaft 178027-001 Nyogel 779 Lubricant 178097-001 Bearing for 0.25-Inch Shaft 178099-003 Steering Wheel 178100-001 Bearing Flange for 0.75-Inch Shaft 178101-001 24 Diametral Pitch x 20° Pressure Angle x 2.500 Pitch Diameter Spur Gear 178101-002 24 Diametral Pitch x 20° Pressure Angle x 0.583 Pitch Diameter Spur Gear

3-11

Page 38

Maintenance, Repair, and Parts Pole Position

005255-04 ON (Bezel) NX

NOTE The shift bezel is not part of the gear shifter assembly and must be purchased separately.

ye See text for lubrication information.

000610-02 (Shifter handle)

78-3002003 (Spring)

76-11375S all bearing) 900609.02 (Shift housing)

7214128 (Screw)

(Switch) (Shift detent)

75-9445 NN (Hex nut) 035301.01 (Actuator pin) 72-JB3606

Figure 3-6 Gear-Shifter Control Assembly A000608-09 Y

Page 39

Pole Position

WARNING

Before you remove or repair any player control, turn the game off.

Removing the Gear-Shifter Control Assembly: Open the control panel (see Figure 3-3). Maintenance, Repair, and Parts

  • To remove the switch, remove the two screws and locknuts that secure the switch to the housing. Be careful not to lose the small actuator pin that sits above the switch actuator.
  • Reassemble in reverse order.
  • To remove the gear-shifter control assembly (see Lubricating the Gear-Shifter Control: Figure 3-4), disconnect the plug-in connectors from I i ql i: fo lubricate the gear-shifter control assembly, open the the i Remove the hardware that secures the control pane! (see Figure 3-3) and remove the gear-shifter gear-shifter control assembly to the control panel. control assembly using the procedure above. Apply a light-
  • To open the gear-shifter assembly, remove the six duty lubricant (such as Nyogel 779) every six months to the screws that secure the two halves of the housing (see spherical part of the handle and the detent. Figure 3-6).

Gear-Shifter Control Assembly Parts List

Assemblies and components listed in the following parts list are shown in Figure 3-6.

Part No. Description 000610-02 Gear-Shifter Handle 65-0214 Single-Pole Single-Throw Low-Force Miniature Switch 72-JB3606 #6 x 0.38-Inch Steel Plastite Screw 7214128 #4-40 x 0.75-Inch Cross-Recessed Pan-Head Steel Machine Screw

76-11375S, ¥%-Inch Ball Bearing 75-944S #4-40 Self-Locking Polymer Hex Nut 78-3002003 Spring 000609-02 Gear-Shifter Housing (two required) 005255-04 Shifter Bezel 035792-01 Shift Detent 035301-01 Actuator Pin 178027-001 Nyogel 779 Lubricant (not shown)

3-13

Page 40

Maintenance, Repair, and Parts Pole Position

On Z 039241-01 (Safety tread)

039240-01 039236-01 (Foot pedal—accelerator) (Pivot =

\ Carriage bolts 00059201 must be installed (Compression spring) betore pivot pin.

178012-004.|4039242.01
(Retaining ring)3a‘(Cable)

7551128 (Carriage bolt)

f (Pulley) 178026-006 Z ; 2 72-8606

(Extension spring)'SScan tere

| Cap screw of pulley must be in | this position when pedal is fully ‘76 5 open (at rest).

(Cable spring)LAE1039239-01

N GET (Base piate) PS | ™ 72.HB34108* 19-9026 (Potentiometer) : (Screw)

160023-001* (Switch) *For Sit-Down cabinet (dual foot-pedal assembly) **For Upright cabinet (single foot-pedal assembly)

SS 03914201" (Mounting plate) 75-9418 : . _ 039379.01"* (Hex locknut) oN 2) — (Mounting plate)

_- Red NY Green x g 75-050S** Black See text for lubrication information (Washer)

Figure 3-7 Foot-Pedal Control Assembly

3-14

Page 41

Pole Position Maintenance, Repair, and Parts

WARNING Before you remove or repair any player control, 3. From the front of the Upright cabinet or in the player turn the game off. area of the Sit-Down cabinet, remove the foot-pedal mounting screws and lift out the foot-pedal control assembly.
  • The only maintenance required on this newly de- Removing the Foot-Pedal Control Assembly: signed foot-pedal control is lubrication every four months (see Figure 3-7). Lubricate the pivot pin and
  • Unlock and open the rear access panel. Reach through surrounding area, the springs, cable, and pulley with the opening to the top of the foot-pedal control. dry teflon spray. If needed, apply a light-duty lubricant
  • Remove the two locknuts located on the top two foot: like WO-40 to the potentiometer shaft only. pedal mounting screws. 5. Reassemble in reverse order.

Foot-Pedal Control Assembly Upright A039413-01 A Sit-Down A039109-01 A Parts List

Assemblies and components in the following parts list are shown in Figure 3-7.

Part No. Description Sit Down Cabinet A039247-01 Dual Foot-Pedal Control Harness Assembly 72-HB3410S, #4-40 x .62-Inch Thread-Forming Hex Washer-Head Screw 75-010S #10 Tooth Internal Lock Washer 160023-001 SPDT Snap Switch with Actuator Upright Cabinet A039463-01 Single Foot-Pedal Control Pedal Harness Assembly 75-0158 Ya-Inch Flat Washer (not shown) 75-050S #10 Tooth Internal Lock Washer 75-5520B #%4-20 x 1.25-Inch Black Carriage Bolt (not shownj 75-915S #%4-20 Hex Nut (not shown) 039379-01 Single Foot-Pedal Control Mounting Plate Upright and Sit-Down Cabinets 19-9026 § kQ Potentiometer 72-8606 #6-32 x .38-Inch Hex Socket-Head Cap Screw 75-9415 #10-24 Hex Locknut 75-5112B #10-24 x .75-Inch Black Carriage Bolt 000592-01 Compression Spring (for pedal) 039236-01 Pivot Pin 039238-01 Pulley 039239-01 Foot-Pedal Control Base Plate 039240-01 Foot Pedal 039241-01 Adhesive Transfer Tape (safety tread) 039242-01 Cable 107012-001 Dry Teflon Spray Lubricant (not shown) 178012-004 External Retaining Ring for %-Inch Diameter Shaft 178026-005 Extension Spring (for cable) 178026-006 Extension Spring (for peda/)

3-15

Page 42

Maintenance, Repair, and Parts

C. Fluorescent Tube and Speaker Replacement

WARNING Before you remove or repair the fluorescent tube or speaker, turn the game off. If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly six feet or more from the implosion. Use care when replacing any fluorescent tube.

Upright Cabinet

Removing the Tube and Speaker Board: From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker's 5-pin harness connector (see Figure 3-8). From the front of the game, remove the three buttonhead screws and lock washers that secure the upper attraction-panel retainer to the cabinet. Loosen the screws and washers that secure the lower attractionpanel retainer to the cabinet. Remove the attraction glass. Remove the lower retainer. Pole Position

Remove the two wood screws that secure the tube and speaker board to the cabinet. Slide this board out of the cabinet. After making necessary repairs or replacements, make sure that the tube and speaker board is pushed all the way back on the tube and speaker panel when you reinstall the board.

Replacing the Fluorescent Tube:

1. Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start. Remove the cardboard locking tab at each end of the tube (see Figure 3-9). Slightly rotate the tube up or down and carefully remove it from the tube hoider. Replace it with a new tube. Do not snap in the tube vigorously— you may break it, causing an implosion! Replace the locking tabs.

Replacing the Upper Speaker:

4. Disconnect the two plug-in connectors on the speaker.

Note that the white wire (+) connects on the side marked with a painted dot. Remove the screws that attach the speaker to the board (see Figure 3-9). Replace with a new speaker and reinstail the tube and speaker board.

Replacing the Lower Speaker: From the back of the game, unlock and open the rear access panel. Refer to upper speaker removal procedure in Figure 3-9.

78-6900402 (Tape) 03941801 (Attraction glass! : graphics)

78-6900402 (Tape)

148001-001 039144-01

(Speaker) (Speaker grille) g

003053-01 (Retainer)

Figure 3-8 Fluorescent Tube and Speaker Board Removal

3-16

Page 43

Pole Position Maintenance, Repair, and Parts

148001-013 70-304 99-11006. a (Soeaker) (Tube) (Tab) Ga

179035-001 : (Tube holder) 03745701 @' i oti ieee (Harness)

142028-001 (Transformer) 142028-002 (Transformer)

99-11003 (Starter) 99-1109 (Socket) (Bracket)

NOTE To make sure that the fluorescent tube starts, check that the ground wire is firmly attached 79-561816P 0306601 to both the ballast transformer and the steel (Wire nut) (Board) tube bracket. A037540-01 (Ground wire)

Figure 3-9 Fluorescent Tube and Speaker Board Assembly U.S.-Built Upright Cabinet A039415-01 A lreland-Built Upright Cabinet A039415-02 A Parts List

Part No. Description For U.S-Built Upright Cabinet 142028-001 60 Hz, 118 V, Ballast Transformer (used on A037458-01 assembly) For lreland-Built Upright Cabinet 142028-002 50 Hz, 118 V, Ballast Transformer (used on A037458-02 assembly) For U.S- and ireland-Built Upright Cabinet A037457-01 Tube and Speaker Harness Assembly A037540.01 Ground Wire with Ring Lug 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥4-Inch Wide x ¥-Inch Thick 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (tab consists of two pieces) 99-1100 Starter Socket 003053-01 Upper and Lower Attraction Glass Retainer 037469-01 Steel Tube Bracket 039366-01 Tube and Speaker Board 039418-01 Attraction Glass with Graphics 148001-013* 6 x 9Inch Ovai, 4-Ohm, 6-Ounce, Shielded High-Fidelity Speaker 179035-001 2-Pin Fluorescent Tube Holder *148001-001 6 x 9Inch Oval, 4-Ohm, 6-Ounce, High-Fidelity Speaker—mounted to the cabinet near the coin docr, behind speaker grille part no. 039144-01

3-17

Page 44

Maintenance, Repair, and Parts

Sit-Down Cabinet

Replacing the Front Speakers:

  • For the right speaker, unlock and open the rear access panel (see Figure 3-10). For the left speaker, open the control panel (see Figure 3-3). Unplug the two plug-in connectors. Remove the two screws that secure the speaker to the wood speaker panel. en Pole Position

Replacing the Seat-Panel Speakers: a)

4, Remove the six wood screws that secure the seatback panel to the cabinet (see Figure 3-10).

  • Lean the seat-back panel forward. Disconnect the two plug-in connectors on each speaker.
  • Remove the seat-back panel from the player area of the cabinet.
  • Remove the four screws that secure each speaker to the seat-back panel.
  • Reassemble in reverse order.

Figure 3-10 Sit-Down Cabinet Speaker Removal

3-18

Page 45

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 46

Maintenance, Repair, and Parts

D. Video Display

WARNING SHOCK HAZARD The following procedure should only be performed by a qualified service technician. Before removing or repairing the video display, turn the game off. High voltages may exist in any video display, even with power disconnected. Use extreme
caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Discharge the high voltage from the cathode ray tube as follows: First, attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Then, wait two minutes and discharge the anode again. IMPLOSION HAZARD {f you drop the display and the picture tube breaks, it will implode! Shattered glass and the yoke can fly six feet or more from the impiosion. Use care when replacing any display.

Removing the Video Display From the Upright Cabinet:

From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-17). Remove the four sets of hardware that secure the video display to the wood display shelf. Open the control panel (see Figure 3-3). Remove the three wing nuts (located on the displayshield support) that secure the dashboard panel to the cabinet. From the front of the cabinet, lift off the dashboard panel. Remove the hardware that secures the display-shield retainer. Lift the display shield up and out of the cabinet. Remove any staples that may secure the bezel to the cabinet. Then, carefully remove the cardboard bezel. Carefully pul! the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.

3-20 Pole Position

Removing the Video Display From the Sit-Down Cabinet:

1. From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-11). Remove the four sets of hardware that secure the video display to the wood display shelf. Open the contro! panel (See Figure 3-3). Move to the player area of the cabinet. Grasp the bottom edge of the video display shield and slide the shield out and down. Make sure the foam tape on the bottom of the shield is in good condition. Remove any staples that may secure the bezel to the cabinet. Then, carefully grasp the bottom edge of the cardboard bezel and remove it from the cabinet. Pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.

Page 47

Pole Position Maintenance, Repair, and Parts

03914801 (Shield) 03914901 039371-01 i (Bese) (Retainer) 039417-01 f (Shiela) 039407-01 H (Bezel) l 92.049 (Electrohome cisplay) or 139003-1004 (Matsushita display)

TS 03936302 : (Shelf) 03912302 (Shelf f / eh SD

Figure 3-11 Video Display Upright and Sit-Down Cabinets Parts List

Part No. Description

For Upright Cabinet

039363-02 Display Sheif 939371-01 Retainer 039407.01 Display Bezel 039417-01 Display Shield For Sit-Down Cabinet

039123-02 Display Shelf 039148-01 Display Shield 039149-01 Display Bezel

For Upright and Sit-Down Cabinets

92-049 19-Inch Electrohome Color Raster-Scan Display Alternate display is part no. 139003-1004—19-Inch Matsushita Color Raster-Scan Display

Page 48

Maintenance, Repair, and Parts Pole Position

E. Utility Panel

A—warninc—A: Before removing or repairing the utility panel, turn the game off. Players may receive an electrical shock if the utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal screw on the back of the coin counter. The utility panel is located inside the upper coin door. This panel includes the volume control(s), self-test switch, auxiliary coin switch, and the coin counter(s) (see Figure 3-12). The auxiliary coin switch is used to credit the game without tripping the coin counter.

NOTE Only Ireland-Built cabinets have two coin counters.

A039254-01 (Dual component 039457-01 harness) (Utility panel— U.S.-Built Upright only) (ey penal 039295-01 sian (Utility panel) harness)

(Coin counter) AM (Vol. control harness) 178070-001 (Vol. control knob)

72-HA4808S (Screw) : ,

f> Le 75-9168 p SELFTESTSWITCH (ev) 7598700 62.041 enon (Stamped nut) (Auxiliary coin switch)

SWITCH NOT USED

Figure 3-12 Utility Panel Assembly A039391-xx C

3-22

Page 49

Pole Position Maintenance, Repair, and Parts

Utility Pane! Assembly Parts List

Part No, Description For U.S-Built Upright Cabinet 039457-01 Utility Panel (for 2 volume controls) For freland-Built Upright Cabinet 039295-01 Utility Panel (for 4 volume controls) For U.S-and treland-Built Upright Cabinet A038004-01 Utility Panel Harness Assembly A039254-01 Dual Component Harness Assembly For U.S-and treland-Built Sit-Down Cabinet A039248-01 Volume Control Harness Assembly 039295-01 Utility Panel (for 4 volume controls) For U.S-and Ireland-Built Upright and Sit-Down Cabinets A002465-01 6 V Coin Counter 19-9032 50 Q, 12.5 W Volume Control 62-041 SPST Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 72-HA4608S #6-32 x Y2-Inch Thread-Forming Screw 75-916S #6-32 Steel Machine Hex Nut 75-9910W0 #15/32-32 Stamped Nut 178070-001 Volume Control Knob

3-23

Page 50

Maintenance, Repair, and Parts Pole Position

F. Coin Doors

170000-001 (Lamp) - 179047-001 MN 99-15023 (Lamp Base) (Base Plate)

99-15056 99-15026 (Coin Inlet) (Screw for Bezel)

99-15025 (Coin Inlet)

Ns J is 99-15054 (Pivot for Lever) 99-15068 Z ay (Lockout Coil) gg945969 9 >< © (Lockout <~

Coil Spring) 99-15055

99-15030 (Lockout Flap)

99-15028 75-9145 [—(Coin Return Box) (Hex Nut) 5

(Lock Wash.)

|-—«— 99-15060 (Sw. Cover)

(Switch)

7214148 (Screw)

Figure 3-13 Vertically Mounted Coin Door A037619-xx D

3-24

Page 51

Pole Position

A037542-01 (Harness—not shown)

99-15073 (Upper Door)

9815063 (Screw) |

om %

99-15067 Lock Assy.)

038091-01 ‘Coin m9 NU oo

A037619-01 — U.S. 25¢/25¢ Coin Door 8037619-02 — U.S. 50¢/50¢ Coin Door A037619-03 — Canadian 25¢/25¢ Coin Door 4037619-04 — British 10 P/10 P Coin Door ‘A037619-05 — British 10 P/S0 P Coin Door A037618-06 — British 20 P/S0 P Coin Door A037619-07 — Australian 20¢/20e Coin Door 99-15070 (Doors and Frame) 99-15072 (Door Frame)

‘A037619-08 —- German 1 DM/1 DM Coin Door ‘A037619-09 — German 2 DM/1 DM Coin Door 403761910 — German 2 DM/5 DM Coin Door A037619-11 — German 1 DM/S DM Coin Door 03761912 — 5 F/5 Fr Coin Door A037619-13 — Swiss 1 Fr/i Fr Coin Door 4037618-14 — French 1 Fr/1 Fr Coin Door Maintenance, Repair, and Parts

99-15038 (Bezel tor Button)

99-15001 thru 99-15011 (Return Button)

9915071 (Clamp)

99-15039 (Bezel for Cover)

99-15036 (Cover)

99-1506 (Screw)

99-15074 (Lower Door)

A037619-15 — French 2 Fr/1 Ft Coin Door ‘403761916 — Swedish 1 Kr/1 Kr Coin Door 03761917 — Spanish 25 Pts/25 Pts Coin Door 403761918 — Italian 100 L/100 L Coin Door A037619-18 — Hong Kong $1/$1 Coin Door ‘A037619-20 —- Japanese 100Y/100Y Coin Door

Figure 3-13 Vertically Mounted Coin Door, continued A037619-xx D

3-25

Page 52

Maintenance, Repair, and Parts Pole Position

Vertically Mounted Coin Door Parts List

Part No. Description A037542-01 Harness Assembly 7214148 #4-40 x 7-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-914S #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Piate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coii (U.S. 25¢) 99-15036 Metal Coin Return Cover 99-15038. Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S, 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x %,.-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15068. Lockout Coil 99-15069 Spring for Lockout Coil 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly) Acceptable substitute is part number A037491-01 170000-001 6.3V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

3-26

Page 53

Pole Position Maintenance, Repair, and Parts

99-10140 (Panel assy.)

75-9488 a (Locknut) all ai 99-1016 LI Aes

ss (

99-10152 (Right coin iniet)

75-9448 (Hex nut)

99-10151 (Left coin inlet)

99.10080 ~ (Lamp oN y 70-11-47 PV (Lamp) CS ¢ -

99-10104 72.9406S (Bar retainer) : 9910147 Ror (Harness)

99-10154 (racket assy)

99-10153 (Coin return box) a i SS ay 99-10042 thru 99-10045, ¥ 2 (Coin switch assy.) Z , ~ oem > : = Ss. (Coin switch ’ a B 99-10150 ~~ K |~———"(Switch cover) . KE

99-10075 thru 99-1078 _~ (Switch wire) 99-10008 75-1412S (Retainer) (Screw)

Figure 3-14 American-Made Coin Door 171027-001 A

3-27

Page 54

Maintenance, Repair, and Parts aDye Pole Position

99-10148 (Lock)

99-10134 99-10119 (Cover) (Button assy.) 99-10118 (Button)

99-10115, (Spring) 72-HA1404C (Screw)

99-10139 $0 (Coin door) ——>] x

99-10141 (Coin return cover)

99-10117 (Coin return door)

99-10144 a g@-on clip)

99-10149 (Service door)

(Coin box)

99-10143 = wa (Frame)

Figure 3-14 American-Made Coin Door, continued 171027-001 A

3-28

Page 55

Pole Position Maintenance, Repair, and Parts

American-Made Coin Door Parts List Assemblies and components in the following parts list are shown in Figure 3-14.

Part No. Description

171006-035, Metal Coin Mechanism for U.S. $.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x %-Inch Truss-Head Screw 72-HA1404C #4-40 x Ya-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x 34-Inch Pan-Head Screw 75-994S #4-40 Lock Nut 99-10608 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99:10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045, Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire (included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (inc/uded in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25

99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10745 Offset Cam (includes 99-10148—Lock) 99-10146 Coin Inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly

3-29

Page 56

Maintenance, Repair, and Parts Pole Position

G. Printed-Circuit Boards

039378-03 (Retainer) A037767-01 (EMI Shield PCB) Shield PCB \ 176015-110 See Figure 3.20 037873-01 (Screw) (Spacer) a

03943101 (End PCB)

aw © T24404F (Screw) 03453602 ‘A037701.01 (Foam pad) 72-4604F (EMI cage) (Screw)

A039187-21 178044-242 v8 A039185-21 Pole Position Video PCB) (Grommet) (Pole Position CPU PCB) ‘ 175009-221 (Washer) NOTE 178045-442 The FCC requires that the game (Fastener) PCB be housed in the EMI cage with the Shield PCB attached.

403543501 176015-110 A035435-05 (Screw) (Regulator/ 175004-708 Audio || PCB) we (Washer)

*Steps 1, 10, and 11 are not illustrated.

Figure 3-15 Removing the Printed-Circuit Boards

3-30

Page 57

Pole Position

WARNING

Before you remove or repair any printed-circuit board, turn the game off.

Removing the Printed-Circuit Boards: Removing the Game PCBs from the EMI Cage

  • Open the rear access panel.
  • The game printed-circuit boards (PCBs) are located inside the electromagnetic interference (EMI) cage (see Figure 3-15). The EMI cage is located on the cabinet wall of the Upright game and on the inside of the rear access panel of the Sit-Down game. Unplug the two harness edge-connectors from the EMI Shield PCB.
  • To remove the game PCBs, pull the eight nylon snap-in fasteners on the EM! Shield PCB to the unlocked position. Carefully slide the Shieid PCB and attached PCBs straight out of their guides. Be careful not to twist the boards, as this may loosen connections or components, Removing the EM! Shield PCB from the Game PCBs
  • Remove the two pan-head screws that connect the EMI Shield PCB to the spacers.
  • Push the EMI Shield PCB off the game PCBs by applying pressure with your thumbs to the edge connec- Maintenance, Repair, and Parts
  • Unpiug the End PCB that connects the two game PCBs.
  • Determine which PCB you need to repair or replace, and remove the two pan-head screws that connect that PCB to the spacers. Replace or repair as required, and reinstall the PCBs. (Make sure the foam vibration damper is placed between the game PCBs.) Removing a Regulator/Audio I! PCB:
  • To remove a Regulator/Audio {| PCB, disconnect the small harness connectors on the board.
  • Remove the hardware that secures the Regulator/Audio !| PCB to the cabinet, and carefully lift the board from the retainer. Do not twist the board, as this may loosen connections or components. Replace or repair as required and reinstali the PCB.
CAUTION

Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them, A reversed connector may damage your game and void the warranty.

  • Close and jock the rear access panel. tors. 11. Important: Perform the self-test.

Printed-Circuit Board Mounting Hardware Parts List

Assemblies and components in the following parts list are shown in Figure 3-15.

Part No. Description

U.S-Built Upright and Sit-Down Cabinets A037701-01 Electromagnetic interference (EMI) Cage (includes guides) 72-1404F #4-40 x %4-Inch Cross-Recessed Steel Screw 72-1604F #6-32 x %-Inch Cross-Recessed Stee! Screw 034536-02 Foam Pad 037873-01 Spacer 039378-03 Dual-Slotted Retainer 175004-708 #8 Fiber Washer 175009-221 Plastic Spacer (for EMI shield PCB) 176015-110 #10 x ¥-Inch Cross-Recessed Pan-Head Screw 178044-242 Grommet 178045-442 Snap-In Fastener Ireland-Built Upright and Sit-Down Cabinets* 7266248 #6 x 1 ¥2-Inch Cross-Recessed Pan-Head Tapping Screw 03453602 Foam Pad 039157-02 Dual-Siotted PCB Retainer 175004-708 #8 Fiber Washer 176015-110 #10 x %Inch Cross-Recessed Pan-Head Screw 178020-750 Nylon Spacer

“Not shown in illustration

3-31

Page 58

Pole Position Maintenance, Repair, and Parts

1 ae A [oes | : 2 walt eo c 4 ° mes |. Be i soe 9 LS :

al Y ara-co) | aram 0

  • H \srapico!) }is7281-c01

J m3 th K #2 Gu . eral mez | Leer | ee L

saa 375 fisava] ret 2 137275-o0: ame a= — = a tly 2s ai 3 2 1

Figure 3-16 Central Processing Unit (CPU) Printed-Circuit Board Assembly A039185-21 A

3-32

Page 59

Pole Position

Parts List

Components in the following parts list are shown in Figure 3-16. Figure 3-16 Central Processing Unit Printed-Circuit Board Assembly Maintenance, Repair, and Parts

DesignatorDescriptionPart No.

Capacitors

C2-C50.01 uF, 100 V Radial-Lead Mylar Capacitor21-101103
Ccé33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor128002-330
C70.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
cg10 pF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250106.
C100.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
Ci47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C120.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C130.01 uF, + 80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C14, C150.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C16-C230.01 uF, + 80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C24, C250.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C2647 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C27, C280.0022 uF, + 10%, 100 V Radial-Lead Plastic Film Capacitor121022-222
C29, C300.022 uF, 100 V Radial-Lead Mylar Capacitor21-101223
C31, C320.01 pF, + 80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C33, C340.047 uF, 100 V Radial-Lead Mylar Capacitor21-101473
C350.022 uF, 100 V Radial-Lead Mylar Capacitor21-101223
C360.0047 uF, 100 V Radial-Lead Mylar Capacitor21-101472
C370.001 yF, 100 V Radial-Lead Mylar Capacitor21-101102
C380.0047 uF, 100 V Radial-Lead Mylar Capacitor21-101472
C39, C400.01 uF, 100 V Radial-Lead Mylar Capacitor21-101103
C4147 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C42, C430.0047 uF, 100 V Radial-Lead Mylar Capacitor21-101472
C44, C450.001 yF, 100 V Radial-Lead Mylar Capacitor21-101102
C46470 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor(24-160477

Acceptable substitute is part no. 24-100477

C47-C5622 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-160226

Acceptable substitute is part no. 24-100477

C57-C840.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C820.001 pF, 100 V Radial-Lead Mylar Capacitor21-101102

Diodes

CR1Type-MV5053 Light-Emitting Diode38-MV5053,
CR26.2 V, +5%, 1 W Type-1N4735A Zener Diode131009-001
CR3-CR5100 V, Type-1N914 Switching Diode31-1N914
CR63.3.V +5% Zener Diode131014-001
CR7.-CR12100 V, Type-1N914 Switching Diode31-1N914

Integrated Circuits

2NType-12L6 Programmable-Array Logic 1137280-001
3AType-Z8002 16-Bit Microprocessor137275-001
3cType-74LS373 Integrated Circuit37-74LS373
3F, 3HCustom Integrated Circuit 10137281-001

(Continued on next page)

3-33

Page 60

Maintenance, Repair, and Parts Pole Position

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
3M, 4CType-74LS373 Integrated Circuit37-74LS373
4F, 4HCustom Integrated Circuit 10137281-001
4MType-74LS373 Integrated Circuit37-74LS373
4NType-Z8002 16-Bit Microprocessor137275-001
5AType-74LS74 Integrated Circuit37-74LS74
5CType-12L6 Programmable-Array Logic 1137280-001
5DType-74LS367 Integrated Circuit37-74LS367
5EType-74LS244 Integrated Circuit37-74LS244
5dType-74LS367 Integrated Circuit37-74LS367
5KType-74LS244 Integrated Circuit37-74LS244
5LType-74LS368 Integrated Circuit137 168-001
5MType-74LS 158 Integrated Circuit137203-001
5NType-74LS74 Integrated Circuit37-74LS74
6AType-74LS 161 Integrated Circuit37-74LS 161
6CType-74LS74 Integrated Circuit37-74LS74
6D-6FType-74LS367 Integrated Circuit37-74LS367
6HCustom Integrated Circuit 08137186-001
6J, 6KType-74LS157 Integrated Circuit37-74LS157
6LType-74LS109 Integrated Circuit37-74LS109
6MType-74LS00 Integrated Circuit37-74LS00
6NType-74S 163 Integrated Circuit137274-001
7cType-10L8 Programmable-Array Logic 3137279-001
7DType-Z80A 8-Bit Microprocessor137194-001
7MCustom Integrated Circuit 07137193-001
7NType-74S04 Integrated Circuit37-74S04
8DType-74LS138 Integrated Circuit137177-001
8EType-74LS259 Integrated Circuit37-74LS259
8FType-74LS367 Integrated Circuit37-74LS367
8HCustom Integrated Circuit 08137186-001
8dType-ADC0804 Integrated Circuit137273-001
8KType-4066 Integrated Circuit37-4066
8LType-4584B Integrated Circuit37-4584B
8MType-74LS04 Integrated Circuit37-74LS04
9ECustom Integrated Circuit 52137284-001
OFACustom Integrated Circuit 54137285-001
9FBType-LM324 Integrated Circuit37-LM324
9HCustom Integrated Circuit 06137192-001
9KCustom Integrated Circuit 53137188-001
9MCustom Integrated Circuit 51137187-001
10AType-74LS138 Integrated Circuit137177-001
10CType-74LS374 Integrated Circuit37-74LS374
10DType-74LS174 Integrated Circuit37-74L8174
10, 10FType-74LS283 Integrated Circuit137204-001
10H, 10dType-74LS273 Integrated Circuit37-74LS273
10K, 10LType-4066 Integrated Circuit37-4066
1AType-74LS174 Integrated Circuit37-74LS174
11Type-7497 Integrated Circuit37-7497
1EType-74LS273 Integrated Circuit37-74LS273

(Continued on next page)

3-34

Page 61

Pole Position Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
11FType-4051 Integrated Circuit137277-001
41HType-74LS174 integrated Circuit37-74LS174
WdType-74LS273 Integrated Circuit37-74LS273
11K-11MType-4066 Integrated Circuit37-4066
WAType-74LS 174 Integrated Circuit37-74LS174
12BType-7497 Integrated Circuit37-7497
12CType-74LS 161 Integrated Circuit37-74.S161
12DType-74LS393 Integrated Circuit37-74LS393
12H, 12J, 12MType-LM324 Integrated Circuit37-LM324

Random-Access Memories

7ECMOS Random-Access Memory137278-001
7d, 7KRandom-Access Memory137199-001

Read-Only Memories

coElectrically Programmable Read-Only Memory136014-106
3EElectrically Programmable Read-Only Memory136014-103
3LElectrically Programmable Read-Only Memory136014-101
4EElectrically Programmable Read-Only Memory136014-104
4LElectrically Programmable Read-Only Memory136014-102
7FElectrically Programmabie Read-Only Memory136014-116
7HElectrically Programmable Read-Only Memory136014-105
7LProgrammable Read-Only Memory136014-117
11DProgrammable Read-Only Memory136014-118
42EElectrically Programmable Read-Only Memory136014-111
12FElectrically Programmable Read-Only Memory136014-110

Resistors

RI220 2, +5%, % W Resistor110000-221
R2-R82.2 kQ, +5%, v4 W Resistor110000-222
lac)1kQ, +5%, % W Resistor110000-102
R10-R162.2 kQ, +5%, Vs W Resistor110000-222
R17-R191k&, +5%, % W Resistor110000-102
R21-R261k&, +5%, % W Resistor110000-102
R27-R342.2 kQ, +5%, Vs W Resistor110000-222
R35,1k, +5%, v4 W Resistor110000-102
R36-R382.2 kQ, +5%, ve W Resistor110000-222
R39-R431kQ, + 5%, V4 W Resistor110000-102
R4547 2, £5%, va W Resistor110000-470
R46, R471kQ, +5%, % W Resistor110000-102
R49-R51220 Q, +5%, Ys W Resistor110000-221
R52470 2, +5%, va W Resistor110000-471
R531kQ, +5%, V4 W Resistor110000-102
R54470 2, +5%, % W Resistor110000-471

(Continued on next page)

3-35

Page 62

Maintenance, Repair, and Parts Pole Position

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R55, R561kQ, +5%, %& W Resistor110000-102
R57-R60470 Q, +5%, Vs W Resistor110000-471
R6147 kQ, +5%, % W Resistor110000-472
R6210 kQ, +5%, %4 W Resistor110000-103
R6322 kQ, +5%, Vs W Resistor110000-223
R6447 kQ, +5%, V4 W Resistor110000-473
R654.7 kQ, +5%, V4 W Resistor110000-472
R6610 k2, +5%, % W Resistor110000-103
R6722 kQ, +5%, 14 W Resistor110000-223
R6847 kQ, +5%, % W Resistor110000-473
R694.7 kQ, +5%, % W Resistor110000-472
R7010 kQ, +5%, % W Resistor110000-103
R7122 kQ, +5%, Vs W Resistor110000-223
R7247 kQ, +5%, Vs W Resistor110000-473
R734.7 kQ, +5%, % W Resistor110000-472
R7410 kQ, +5%, % W Resistor110000-103
R7522 kQ, +5%, % W Resistor110000-472
R7647 kQ, +5%, v4 W Resistor110000-473
R77-R801kQ, +5%, % W Resistor110000-102
R81220 2, + 5%, % W Resistor110000-221
R821kQ, 5%, Ys W Resistor110000-102
R83470 Q, +5%, v4 W Resistor110000-471
R841kQ, +5%, % W Resistor110000-102
Re5,2.2 kQ, +5%, V4 W Resistor110000-222
R86330 2, +5%, v4 W Resistor110000-331
R871kQ, £5%, % W Resistor110000-102
R8822 kQ, +5%, Vs W Resistor110000-223
R89-R921kQ, +5%, V4 W Resistor110000-102
R93, R94330 2, +5%, v4 W Resistor110000-331
RO51kQ, +5%, % W Resistor110000-102
ROG4.7 kQ, 5%, Vs W Resistor110000-472
R97220 2, +5%, % W Resistor110000-221
RIB2.2 kQ, +5%, ve W Resistor110000-222
R99220 2, +5%, v4 W Resistor110000-221
R1012.2 kQ, +5%, % W Resistor110000-222
R102, R1041kQ, 5%, Y4 W Resistor110000-102
R1034.7 kQ, +5%, Ys W Resistor110000-472,
R106-R1151kQ, +5%, Vs W Resistor110000-102
R1161.5 kQ, +5%, % W Resistor110000-152
R1171kQ, +5%, V4 W Resistor110000-102
R1184.7 kQ, +5%, % W Resistor110000-472
R11910 k&, +5%, % W Resistor110000-103
R120, R12122 kQ, +5%, V4 W Resistor110000-223
R122120 kQ, + 5%, ¥% W Resistor110000-124
R123470 Q, +5%, % W Resistor110000-471
R12447 kQ, +5%, % W Resistor110000-473
R12512 kQ, +5%, %& W Resistor110000-123
R1264.7kQ, +5%, v4 W Resistor110000-472

(Continued on next page)

3-36

Page 63

Pole Position Maintenance, Repair, and Parts

Ceniral Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R127, R1282.2 kQ, +5%, Ys W Resistor110000-222
R129, R1303.3 kQ, +5%, % W Resistor110000-332
R13110 kQ, +5%, %4 W Resistor110000-103
R13222 kQ, +5%, % W Resistor110000-223
R13315 kQ, +5%, % W Resistor110000-153
R134120 kQ, +5%, % W Resistor110000-124
R135470 2, +5%, Vs W Resistor110000-471
R13647 kQ, + 5%, Ye W Resistor110000-473
R13715 kQ, +5%, % W Resistor110000-153
R13810 kQ2, +5%, % W Resistor110000-103
R13922 kQ, +5%, v4 W Resistor110000-223
R140180 kQ, +5%, % W Resistor110000-184
R141470 2, +5%, Ya W Resistor410000-471
R142, R14322 k2, +5%, v4 W Resistor110000-223
R144-R1511kQ, +5%, Y W Resistor110000-102
R15247 kQ, +5%, V4 W Resistor110000-473
R153470 Q, +5%, 4 W Resistor110000-471
R15410 k2, +5%, % W Resistor110000-103
R15582 kQ, +5%, % W Resistor110000-823
R156, R15747 kQ, +5%, % W Resistor140000-473
R15822 kQ, +5%, % W Resistor110000-223
R15947 kQ,+5%, V4 W Resistor110000-473
R160100 kQ, +5%, % W Resistor110000-104
R161-R1652.2 kQ, +5%, ¥% W Resistor110000-222
R1661kQ, +5%, % W Resistor110000-102
R1672.2 kQ, +5%, % W Resistor110000-222
R1684,7 kQ, +5%, V4 W Resistor110000-472
R169220 k2, +5%, % W Resistor110000-224
R170390 k2, +5%, % W Resistor110000-394
R1714.7 kQ, +5%, Ys W Resistor110000-472
R17215 kQ, + 5%, v4 W Resistor110000-153
R17347 kQ, +5%, % W Resistor110000-473
R17433 kQ, +5%, % W Resistor110000-333
R17510 kQ, +5%, % W Resistor110000-103
RI7647 kQ, +5%, v« W Resistor110000-473
R1771kQ, +5%, Y% W Resistor110000-102
R17875 kQ, +5%, % W Resistor110000-752
Ri79330 kQ, +5%, Ya W Resistor110000-334
R180, R18147 kQ, +5%, % W Resistor110000-473
R1821k2Q, +5%, % W Resistor110000-102
R18322 kQ, +5%, v% W Resistor110000-223
R18415 kQ, +5%, ¥% W Resistor110000-153
R18510 kQ, +5%, % W Resistor410000-103
R1861k, +5%, % W Resistor110000-102
R187330 kQ, +5%, v4 W Resistor110000-334
R18810 kQ, 5%, 4 W Resistor110000-103
R189, R19047 kQ, +5%, %& W Resistor110000-473
R1911k, +5%, % W Resistor110000-102

(Continued on next page)

3-37

Page 64

Maintenance, Repair, and Parts Pole Position

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R19275 kQ, +5%, vs W Resistor110000-753
R19315 kQ, +5%, V4 W Resistor110000-153.
R19447 kQ, +5%, Vs W Resistor110000-473
R19510 kQ, +5%, % W Resistor110000-103
R1961kQ, +5%, “4 W Resistor110000-102
R197, R19847 kQ, +5%, Vs W Resistor110000-473
R1991kQ, +5%, % W Resistor110000-102
R20047 kQ, +5%, % W Resistor110000-473
R20115 kQ, +5%, %4 W Resistor110000-153
R20210 kQ, +5%, % W Resistor110000-103
R2031kQ, +5%, % W Resistor110000-102
R204, R20547 kQ, +5%, V4 W Resistor110000-473
R2061kQ, +5%, % W Resistor110000-102
R20720 kQ, +5%, % W Resistor110000-203
R20810 k2, +5%, v4 W Resistor110000-103
R20920 k2, +5%, v4 W Resistor110000-203
R21010 kQ, +5%, % W Resistor110000-103
R21120 kQ, +5%, V4 W Resistor110000-203
R21210 kQ, +5%, % W Resistor110000-103
R21320 kQ, +5%, % W Resistor110000-203
R21410 k2, +5%, % W Resistor110000-103
R21520 kQ, +5%, Vs W Resistor110000-203
R21610 kQ, +5%, V4 W Resistor110000-103
R21720 kQ, +5%, V4 W Resistor110000-203
R21810 kQ, +5%, V4 W Resistor110000-103
R21920 kQ, +5%, v4 W Resistor110000-203
R22027 kQ, +5%, Vs W Resistor110000-273
R2231kQ, +5%, % W Resistor110000-102
R225-R2311kQ, +5%, % W Resistor110000-102
R231-R2382.2 kQ, +5%, V4 W Resistor110000-222
R239-R2441kQ, +5%, % W Resistor110000-102
R245100 2, +5%, %& W Resistor110000-101
R246150 kQ, +5%, V4 W Resistor110000-154
1E2.2 kQ, + 2%, Dual-Inline-Package Resistor Network118003-222
ON1k, +2%, Dual-Inline-Package Resistor Network118003-102

Sockets

3A40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
3E, 3F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
3H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
3b28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4E, 4F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4l28-Contact Medium-Iinsertion-Force Integrated Circuit Socket79-42C28
4N40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40

(Continued on next page)

3-38

Page 65

Pole Position Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
6H-9H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
7D40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
7E, 7F24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
7H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
7M28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8A28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8C28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9c28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9E42-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C42
OFA28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9K42-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C42
9M42-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C42
12E, 12F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28

Switches

QUA8-Station, Single-Throw, Dual-Inline-Package Bit Switch66-118P IT
9L8-Station, Singie-Throw, Dual-Inline-Package Bit Switch66-118PIT

Transistors

QiType-2N3906 40 V, 1 W, PNP Transistor33-2N3906
Q2Type-2N3904 60 V, 350 mW, NPN Transistor34-2N3904
Q3Type-MPS-A92 300 V, 500 mA, PNP Transistor33-MPSA92
Q4Type-2N3904 60 V, 350 mW, NPN Transistor34-2N3904
Q5, 06Type-2N6044 80 V, 8 A, Darlington NPN Transistor34-2N6044

Miscellaneous

BTt3.6 V, 100 mA Nickel-Cadmium Battery171028-001
WtLead-Spring Socket Terminal179131-001

Test Point Acceptable substitute is part no. 020670-01 179051-001 Jumper Staple 15009-001

Q5, Q6Nylon Snap-In Fastener81-4302

3-39

Page 66

Pole Position Maintenance, Repair, and Parts

ao co ‘ig #

a as a = BS

anes?

A Figure 3-17 Pole Position Video Printed-Circuit Board Assembly A039187-21

3-40

Page 67

Maintenance, Repair, and Parts Pole Position

Pole Position Video Printed-Circuit Board Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

C2470 uF, 16 V Aluminum Electrolytic Axial-Lead Capacitor Acceptable24-160477

substitute is part no. 24-100477

C3-C1722 uF, 16 V Aluminum Electrolytic Axial-Lead Capacitor24-160226
C18-C570.1 uF, + 80, -20%, 50 V Ceramic Disk Radial-Lead Capacitor122002-104
C5868 pF, 100 V, Mica Capacitor128002-680
C5922 pF, 100 V, Mica Capacitor128002-220

Diodes

CRIType-MV5053 Light-Emitting Diode38-MV5053
CR2Type-1N4735A, 6.2 V, 1 W Zener Diode131009-001

Inductors

LI-L3,1 uH, 2 W Inductor141007-001
L4100 wH, + 10% Inductor141002-001

Integrated Circuits

2AType-74LS138 Integrated Circuit137177-001
2EType-74LS74 Integrated Circuit37-74LS74
2HType-74LS139 Integrated Circuit37-74LS 139
2dType-74LS10 Integrated Circuit37-74LS10
2KType-74LS368 Integrated Circuit137168-001
3BType-74LS283 Integrated Circuit137204-001
3cType-74LS283 Integrated Circuit137204-001
3DType-74LS283 Integrated Circuit137204-001
3HType-74LS175 integrated Circuit37-74LS175,
Su, 4dType-74LS174 Integrated Circuit37-74LS 174
3KType-74LS283 Integrated Circuit137204-001
3LType-74LS283 Integrated Circuit137204-001
3MType-74.S02 Integrated Circuit37-74LS02
4BType-74LS367 Integrated Circuit37-74LS367
4cType-74LS367 Integrated Circuit37-74LS367
4HType-74LS157 Integrated Circuit37-74LS157
4kType-74LS174 Integrated Circuit37-74LS174
4M, 5MType-74LS298 Integrated Circuit137201-001
4N, SNType-74LS283 Integrated Circuit137204-001
5BType-74LS174 Integrated Circuit37-74LS174
5CType-74LS174 Integrated Circuit37-7ALS174
5DType-74LS174 Integrated Circuit37-74LS174
SEType-74LS245 Integrated Circuit37-74LS245
SF, 6FType-74LS245 Integrated Circuit37-74LS245
5HType-74LS175 Integrated Circuit37-74LS175
SuType-74LS273 Integrated Circuit37-74LS273
6AType-74S04 Integrated Circuit37-74S04
6BType-74LS368 Integrated Circuit137168-001
6CType-74LS08 Integrated Circuit37-74LS08
6HType-74LS245 Integrated Circuit37-74LS245
6dType-74LS245 Integrated Circuit37-74LS245
6KType-74LS245 Integrated Circuit37-74LS245,
6M, 7MType-74LS273 Integrated Circuit37-74LS273
7BType-74S163 Integrated Circuit Acceptable substitute is part no.137274-001

137287-001 or -002

7GType-74S04 Integrated Circuit37-74S04
7DType-74LS32 integrated Circuit37-74LS32

(Continued on next page)

Page 68

Maintenance, Repair, and Parts Pole Position

Pole Position Video Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
7LType-74LS273 Integrated Circuit37-74LS273
8BType-74S00 Integrated Circuit37-74S00
8C,9CType-74LS157 Integrated Circuit37-74LS157
8DType-74LS158 Integrated Circuit137203-001
8EType-74LS158 Integrated Circuit137203-001
8L,9LType-74LS174 Integrated Circuit37-74LS174
9BType-74LS20 Integrated Circuit37-74LS20
9DType-74LS298 Integrated Circuit137201-001
9E, 10EType-74LS257 Integrated Circuit37-74LS257
9HType-74LS161 Integrated Circuit37-74LS161
QJType-74LS161 Integrated Circuit37-74LS161
9KType-7497 Integrated Circuit37-7497
9M, 10MType-74LS283 Integrated Circuit137204-001
ONType-74LS85 Integrated Circuit37-74LS85
10BType-74LS74 Integrated Circuit37-74LS74
10CType-74LS174 Integrated Circuit37-74LS174
10DType-74LS368 Integrated Circuit137168-001
10HType-74LS161 Integrated Circuit37-74LS161
10JType-74LS161 Integrated Circuit37-74LS161
10KType-74LS161 Integrated Circuit37-74LS161
10LType-74LS161 Integrated Circuit37-74LS161
10NType-74LS85 Integrated Circuit37-74LS85,
11BType-74107 Integrated Circuit Acceptable substitute is part no.37-74107

137169-001

1FType-74LS174 Integrated Circuit37-74LS174
41HType-74LS174 integrated Circuit37-74LS174
11dType-74LS273 Integrated Circuit37-74LS273
11KType-74LS139 Integrated Circuit37-74LS139
VLType-74LS373 Integrated Circuit37-74LS373
11MType-74LS373 Integrated Circuit37-74LS373
12BType-74LS86 Integrated Circuit37-74LS86
12FType-74LS86 Integrated Circuit37-74LS86
13FType-74LS20 Integrated Circuit37-74LS20

For -21 version only

2FType-07 Custom Integrated Circuit137193-001
3NType-02 Custom Integrated Circuit137190-001
4DType-09 Custom Integrated Circuit137282-001
SL, 6LType-03 Custom Integrated Circuit137283-001
7EType-04 Custom Integrated Circuit137191-001
8NType-02 Custom Integrated Circuit137190-001
13HType-02 Custom Integrated Circuit137190-001

Random-Access Memories

3E, 4ERandom-Access Memory (200 ns) Acceptable substitute is part no.137198-001

137211-001 (150 ns)

SF, 4FRandom-Access Memory (200 ns) Acceptable substitute is part no.137198-001

137211-001 (150 ns)

7F, 8FType-2114-2 (200 ns) Random-Access Memory90-7036
7H, 8HType-2114-2 (200 ns) Random-Access Memory90-7036
7d, BdType-2114-2 (200 ns) Random-Access Memory90-7036
7K, 8KType-2114-2 (200 ns) Random-Access Memory90-7036
QF, 10F55 ns Random-Access Memory137199-001

(Continued on next page)

Page 69

Pole Position Maintenance, Repair, and Parts

Pole Position Video Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.

Programmable Read-Only Memories

2BType-82S129(17) Programmable Read-Only Memory136014-144
20Type-82S129(16) Programmable Read-Only Memory136014-143
2DType-82$129(15) Programmable Read-Only Memory136014-142
4Type-82S137(12) Programmable Read-Only Memory136014-145
5KType-82S129(11) Programmable Read-Only Memory136014-141
6DType-82S123(14) Programmable Read-Only Memory136014-136
6EType-82S123(13) Programmable Read-Only Memory136014-135
8MType-82S129(10) Programmable Read-Only Memory136014-140
1cType-82S129(9) Programmable Read-Only Memory136014-139
11DType-82S129(8) Programmable Read-Only Memory136014-138,
METype-82S129(7) Programmable Read-Only Memory136014-137
12HType-82S137(6) Programmable Read-Only Memory136014-146

For -21 version only

2LElectrically Programmable Read-Only Memory136014-127
2MElectricatiy Programmable Read-Only Memory136014-128
2NElectrically Programmable Read-Only Memory Acceptable substitute136014-134

is part no. 137205-001

6NElectrically Programmable Read-Only Memory Acceptable substitute136014-133

is part no. 137205-001

7NElectrically Programmable Read-Only Memory Acceptable substitute136014-132

is part no. 137205-001

1iNElectrically Programmable Read-Only Memory136014-131
12JElectrically Programmable Read-Only Memory136014-120
12KElectrically Programmable Read-Only Memory136014-122
12,Electrically Programmable Read-Only Memory136014-124
12NElectricaily Programmable Read-Only Memory136014-126
13dElectrically Programmable Read-Only Memory136014-119
13KElectrically Programmable Read-Only Memory136014-121
13LElectrically Programmable Read-Only Memory136014-123
13NElectrically Programmable Read-Only Memory136014-125

Resistors

RI1-R92.2 kQ, +5%, %4 W Resistor110000-222
R10-R241kQ, +5%, % W Resistor110000-102
R25-R40470 Q, +5%, V4 W Resistor110000-471
R41~R48.4.7 kQ, +5%, Vs W Resistor110000-472
R49-R521kQ, +5%, Vs W Resistor110000-102
R55-R581kQ, +5%, % W Resistor110000-102
R59220 2, +5%, V4 W Resistor110000-221
R60470 2, +5%, V4 W Resistor110000-471
R611kQ, +5%, 4 W Resistor110000-102
R622.2 k&, +5%, Vs W Resistor110000-222
R66220 2, +5%, % W Resistor110000-221
R67470 Q, +5%, V4 W Resistor110000-471
R681kQ, +5%, % W Resistor110000-102
R692.2 k2, +5%, V4 W Resistor110000-222
R73220 2, +5%, V4 W Resistor110000-221
R74470 2, +5%, Ya W Resistor110000-471
R751kQ, +5%, % W Resistor110000-102
R762.2 kQ, +5%, v4 W Resistor110000-222
R801kQ, +5%, V4 W Resistor110000-102
R81100 2, +5%, % W Resistor110000-101

(Continued on next page)

3-43

Page 70

Maintenance, Repair, and Parts Pole Position

Pole Position Video Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R82-R851kQ, +5%, % W Resistor110000-102
R86220 2, +5%, % W Resistor110000-221
R87-R981kQ +5%, % W Resistor110000-102
RaQ10 kQ, +5%, % W Resistor110000-103
R100220 2, +5%, % W Resistor110000-221
R10110 kQ, +5%, % W Resistor110000-103
R1021.5 kQ, +5%, ¥% W Resistor110000-152
R103-R10562 Q, +5%, v4 W Resistor110000-820
1B2.2kQ, +2%, 15-Element, Oual-Inline Package Resistor Pack118003-222
1K2.2 kQ, +2%, 15-Element, Dual-Inline Package Resistor Pack118003-222

Sockets

2F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
2u28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
2M28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
2N24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
3E, 4€24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
3F, 4F24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
3N28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4D24-Contact Medium-insertion-Force Integrated Circuit Socket79-42C24
SL, 6L18-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C18
6N, 7N24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
7E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42028
8N28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
TIN24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
12J, 13028-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
12K, 13K28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
12L, 13L28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
12N, 13N28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42028
13H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42028

Transistor

Q4Type-2N3904, 60 V, 1 W, NPN Transistor34-2N3904

Miscellaneous Test Points Acceptable substitute is part no. 020670-01 17905 1-002

Y1B24.576 MHz Crystal Acceptable substitute is part no. 144004-002144004-003

3-44

Page 71

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specilic written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession hereof confers or transfers any tight in, oF license 0 use, the subject maiter of the drawing of any design or technical information shown thereon, nor any right fo reproduce this drawing or any part thereo! Except for manufacure by vendors of Atari Inc, ang for manufacture under the corporation's written license. no Fight to reproduce this drawing is granted or the subject mat: ter thereot unless by written agreement with or wrilten permis sion from the corporation Maintenance, Repair, and Parts

R24,12,7W

U.S.-Built Cabinet A035435-01 G jure 3-18 Regulator/Audio Il PCB Assembly

3-45

Page 72

Maintenance, Repair, and Parts

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden witnout the spe: cific written permission of Atari, Inc., Sunnyvale, CA, This drawing 's only conditionally issued, and neither receipt nor possession thereof confers or transters any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor any fight to reproduce this drawing or any part thereo!. Except for manufacture by vendors of Atar, Inc., and for manufac ture under the corporation's written license, no right to re: produce this drawing is granted or the Subject matter thereof unless by written agreement wit or written permis: sion trom the corporation,

Figure 3-19 Regulator/Audio || PCB Assembly lreland-Built Cabinet A035435-05 A

3-46 Pole Position

Page 73

Pole Position Maintenance, Repair, and Parts

Regulator/Audio |i PCB Assembly Parts List

Assemblies and components in the following parts list are shown in Figures 3-18 and 3-19.

DesignatorDescriptionPart No.

Capacitors

For -01* and -05** versions

C1470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
c20.001 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor422002-102
cs0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C131000 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108

For -01 version

C30.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088,
c4470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cs0.01 yF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable100015-103

substitute is part no. 122005-103

cé0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C70.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C9, C103300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
foab0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
C12470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C140.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable100015-103

substitute is part no. 122005-103

Cci50.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C170.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
C20, C210.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
C22, C231 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500105

Diodes

For -07 and -05 versions

CR1Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR4Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002

Integrated Circuits

For -01 and -05 versions

QiType-LM308, 5 V, Linear Voltage Regulator37-LM305

For -01 version

a5Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002
Q7Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002

{Continued on next page)

“Acceptable substitutes are A035435-02 or -04. **Acceptable substitutes are A035435-01, -02, or -04.

Page 74

Maintenance, Repair, and Parts

Regulator/Audio If PCB Assembly Parts List, continued Pole Position

DesignatorDescriptionPart No.

Resistors

For -01 and -05 versions

R1270 Q, +5%, V4 W Resistor110000-271
RS33 Q, +5%, Y% W Resistor110000-330
R4100 2, + 5%, % W Resistor110000-101
R527 2, 5%, 1 W Resistor110009-027
R63.9 kQ, +5%, % W Resistor110000-392
R775 kQ, +5%, v4 W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer Acceptable19-315102

substitute is part no. 119002-102

R240.1 2,+3%, 7 W Wirewound Resistor19-100P 1015.
R29, R3010 2, +5%, % W Resistor110000-100

For -01 version

RQ220 Q, 5%, v2 W Resistor110001-221
R101Q, +5%, % W Resistor110000-010
R1110.2,5%, V4 W Resistor110000-100
Ri2100 2, +5%, Y4 W Resistor110000-101
R13, R1410 k2, +5%, % W Resistor110000-103
R191, +5%, % W Resistor110000-010
Reo102, +5%, V4 W Resistor110000-100
R21220 2, +5%, ve W Resistor110001-221
R22"100 2, +5%, % W Resistor110000-101
R27, R281kQ, +5%, Ya W Resistor110000-102

Transistors For -01 and -05 versions

Q2Type-TIP32 PNP Power Transistor33-TIP32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055

Mechanical Parts For -01 and -05 versions

J66-Position Connector Receptacle79-58306
J79-Position Connector Receptacle79-58308
Q3#6-32 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Stee!72-1608,

Machine Screw

Q2, Q3#6-32 Nut/Washer Assembly75-99516
Q2Thermally Conductive Silicon Insulator78-16014
Q3Thermally Conductive Silicon Insulator78-46008
Q5#6-32 x Vs-Inch Binder-Head Nylon Screw75-F60405,

Heat Sink 034531.01 Test Point Acceptable substitute is part no. 020670-01 179051-001

For -07 version

J84-Position Connector Receptacle7958354
Qs#6 x %Inch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc-72-6606S

Plated-Steel Screw

Page 75

Pole Position Maintenance, Rep:

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONETBEN AL nepesicton fomrasen enmeut ne opeens Gnitenpermoson efter ne, Seema Nahe craneaes My constonely issued. and nether recep nar posseeaon frefech comers or taretare ery newer eemeetoane ioe Subject snaterol ine ertwing Faby design rtasmace sao alan shaw werent ear en rign ener See reng Se a sep a a enracuce Mis craving Tene ‘se nan io vepreauce ie drawing grenied'or ne Subject ratte rere anise by: writen agresrees wn oe salen poangosh em ihe someon

co co Co} Gores — (oice to

so CS rT Cepciz Goes Coca rcs ta ce Coa co orang co Gtre2:

9| apes pean Socas {7 -44, 470PrF talons oh cdc .a70rF 123447 270° Goce

=

Gocs4 fo) cocss [_

Figure 3-20 EMI Shield PCB Assembly A037667-01 A

3-49

Page 76

Maintenance, Repair, and Parts Pole Position

EMI Shield PCB Assembly Parts List

Components in the foliowing parts list are shown in Figure 3-20.

DesignatorDescriptionPart No.

Capacitors

C1-C50.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C6-C120.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor422005-103
C13-C150.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
Cié0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C17-C240.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C25-C310.01 uF, + 80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C32,C330.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C34-C390.01 pF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C40-C430.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C440.471 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-471
C450.001 uF, + 80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-102
46,0470.471 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-471
C480.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C54,C550.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104

Connectors

P1930-Pin Card-Edge Connector179046-030
P2044-Pin Card-Edge Connector179046-044

Miscellaneous

#4-40 x Y2-Inch Cross-Recessed Pan-Head Machine Screw (not shown) 72-1408C #4 Flat Washer (not shown) 75-024C #4-40 Nut/Washer Assembly (not shown) 75-995 14

Page 77

Pole Position Maintenance, Repair, and Parts

H. Power Supply Assembly

WARNING A03588-01 Fuse cover must be in place dur- (Transformer assy.) ing game operation.

A021084-xx (Voltage plugs) 29-053 i g (Capacitor) S i 03454401 (Fuse block cover) 78-70501SC | (Capacitor bracket) 79-4411001 (Fuse post)

46-2017002 (Fuse)

29-053 (Capacitor) A035891-02 < 034482-02 (Fuse harness assy.) 2 y (Chassis)

78-2708 (Bushing)

A034630-01 (Filter Assy.) 79-3206 (Fuse block) 037641-01 78-70501SC (Label) (Bracket)

79-15021001 A035890-0 (Terminal block) \ (Power harness) A034629-01 3A-MDA3501 (AC harness) (Rectifier)

Figure 3-21 Power Supply Assembly A037671-xx G

3-51

Page 78

Maintenance, Repair, and Parts Pole Position

Power Supply Assembly Parts List

Assemblies and components in this parts list are shown in Figure 3-21.

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100V(90-110 VAC)(violet)
A021084-02Voltage Plug for 120V(105-135 VAC)(yellow)
A021084-04Voltage Plug for 220V(200-240 VAC)(blue)
A021084-05Voltage Plug for 240V(220-260 VAC)(brown)

A034629-01 AC Harness Assembly

A034630-01RFI Filter Assembly(FL1—designation not marked)

A035888-01 Upright and Cabaret Transformer Assembly (T1) Acceptable substitute is part no. A035888-02 A035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6)

29-05327,000 pF 15V DC Electrolytic Capacitor(C1)

3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140024 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30125325 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %,-Inch Outside Diameter x ‘4-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket (C1)

79-150210012Circuit Single-Row Terminal Block(located under F4)

79-3206 5-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals (F2-F6) 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post (F1) 03448202 Power Supply Chassis 034544-01 Fuse Block Cover (F2-F6)

037639-03, -04Label for Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)

03767104 power supply has the 120 V plug. A037671-05 has the 100 V, 220 V and 240 V plugs. A037671-06 has the 220 V and 240 V plugs.

3-52

Page 79

Pole Position

Glossary of Terms

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for START is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the Strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating the coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to acontrol panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT

A binary digit; expressed as a 1 or

a0. BLANKING Turning off the beam on a cathoderay tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.

CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass.

CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electro-mechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. Glossary

COMPOSITE VIDEO Complete video signal from the game system to drive the display cir- Cuitry, usually comprising H SYNC, V SYNG, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA Generai term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. pc Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electro-magnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, Capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output poris and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage.

GL

Page 80

Glossary

GATE

  • A circuit with one output that responds when and only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) ina TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +08 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 vDC MULTIPLEXER A device that takes several lowspeed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER
  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images. are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathoderay tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (@.g., the ATARI® CAT Box) convert lengthy bit Pole Position

streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 81

Pole Position Ast printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

lf you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm Gi Distributor

Address 1 Operator City State Zip Co Other.

Area Code Phone

Page 82

First fold

Attach Necessary Postage

Atari \reland Limited Atin.: Field Service/Coin-Op Division

Tipperary Town, Ireland

Second fold

swol4 eBpe siyy edey

Page 83

First fold

No Postage Necessary Hf mailed in the United States

Ce

BUSINESS REPLY MAIL ee FIRSTCLASS PERMIT NO. 1004 SUNNYVALE, CA Eee

POSTAGE WILL BE PAID BY ADDRESSEE =e

Atari, Inc. es Attn.: Field Service/Coin-Op Division a P. O. Box 427 Sunnyvale, California 94086 pt bn a

WOl4 abpa siy) odes

Page 84

Pole Position 1st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technicai questions about certain ATAR! games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm O Distributor

Address O Operator City State Zip (CD Other

Area Code _. Phone

Page 85

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 86

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 87

GE PE GE PE ES,

> > > > >

Fdsee Nil Natee Nah | Satee, ae! Sata Nated

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant, and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. iz « © % ©

© = AN

Page 88

ATARI, INC. 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488