CATHODE RAY TOMES

Galaxian Cocktail Parts and Operating Manual (April 1980)

Galaxian (Namco set 1) (Namco, 1979) · Parts & Operating Manual · 28 pages · 17 sections · original scan

Page 1

GAME NO. 869 APRIL, 1980

MIDWAY’S

Colles GR **COCKTAIL”’

PARTS AND

OPERATING MANUAL

38028 HOIH «nT + * & » A » Ea » # & i

10750 WEST GRAND AVENUE

FRANKLIN PARK, ILLINOIS 60131

U.S.A.

PHONE: (312) 451-1360 CABLE ADDRESS: MIDCO TELEX NO.: 72-1596

Page 2

TABLE OF CONTENTS

Page No.

GENERAL INSTRUCTIONS 1-2

MONITOR - GENERAL INFORMATION 3-5

SWITCH ADJUSTMENTS 6

NO. 869 - GALAXIAN COCKTAIL - PICTURE 8-9

INTERIOR ACCESS PICTURE 10-11

CONTROL SHELF ASSEMBLY 12-13

TRANSFORMER BOARD ASSEMBLY 14-15

COIN DOOR ASSEMBLY 16-17

GAME BOARD COMPONENT LAYOUT 18

GAME BOARD SCHEMATIC 19

MEMORY BOARD SCHEMATIC. 20

WIRING DIAGRAM SCHEMATIC 21

ELECTROHOME MONITOR SCHEMATIC 22

GAME LOGIC CHIP NUMBER & FUNCTION 23-24

WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

COPYRIGHT 1980 ©BY MIDWAY MFG. CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELEC- TRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY |T BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131

Page 3

GENERAL INSTRUCTIONS FOR “GALAXIAN” COCKTAIL TABLE

INSTALLATION

  • Remove shipping cleats located on bottom of cabinet.
  • Install four (4) provided leg levelers to bottom of cabinet and level cabinet.
  • The power is controlled by a switch located on the bottom of the cabinet. Additional taps have been provided on the transformer to compensate for fluctuating line voltage.

LINE VOLTAGE SAFETY SWITCH A line voltage safety switch has been provided for your protection. It is located in the cabinet on the left side of the coin door. When the coin door is opened the circuit to the line voltage is interrupted. To restore power (when servicing), pull switch fully out.

VOLUME CONTROL The volume control pot is located on the Game Logic Board (P.C. A082-91352-A/B000). The pot controls the volume of all sounds and may be varied as desired by rotating pot control.

ADJUSTMENT SWITCHES

Located on Game Logic Board (P.C. A082-91352-A/B000) and may be adjusted as indicated on separate instruction card in back box area.

GAME LOGIC P.C. A082-91352-A/B000

ADJ. SW.

VOLUME CONTROL

CREDIT PUSH BUTTON SWITCH

Located to right of cash box and is readily accessible by opening coin door. This switch is provided as a test aid and awards one credit without advancing coin meter.

TEST SLIDE

Located to right of cash box and is readily accessible by opening coin door. When placed in “ON” position, this switch initiates test mode.

Page 4

GAME BOARD TEST

Place test slide switch in “ON” position. If game board is good, the following information will be displayed on the screen: OK Coin Adjustment Setting Bonus Adjustment Setting Number of Galaxip Per Game Setting

RAM/ROM TEST

If any of the Rams or Roms are faulty, the following information will be displayed on the screen: “Bad Ram 1” — indicates bad Ram at location 7N or 7P. “Bad Ram 2” — indicates bad Ram at location 3F or 3H. “Bad Ram 3” — indicates bad Ram at location 4FH or 5FH. “Bad Rom” — indicates bad Rom on memory board.

CONTROL PANEL AND COIN SWITCH TEST

To verify operation of any switch, close switch in question. If switch is operating properly, a game sound will emit when closure is made.

Caution: Be sure to return test switch to game mode when all tests are completed.

TO SERVICE MONITOR, GAME BOARD AND TRANSFORMER ASSY. 1, Open coin box door and release two (2) clamps indicated on sketch below.

  • Grasp monitor mounting panel at “A” and open as indicated in sketch below.
Caution: Due to the weight of the monitor extreme care must be exercised when opening cabinet for service.
Page 5

MONITOR - GENERAL INSTRUCTIONS Service Set-Up Procedure

NOTE: All monitors are equipped with automatic degaussing coils which effectively demagnetize the picture tube each time the monitor is turned on. The degaussing coiis will operate any time the set is turned on after having been off for at least five minutes.

The degaussing effect is confined to the picture tube since the coils are mounted on the ferrous tube shield. Should any part of the chassis or cabinet become magnetized, it will be necessary to degauss the affected area by means of amanual degaussing coil. Move the coil slowly around the CRT face area, then slowly withdraw for a distance of six feet before disconnecting the coil from the AC power supply. Normally little, if any adjustment should be necessary. However, when a picture tube, yoke or similar component is replaced, preliminary static convergence should be done before attempting purity adjustment, and so on. Set up should be done in a north/south direction. Horizontal and vertical centering taps should be set to the centre position if a major component has been changed. 1.0 Purity

1.3

1.4

1.5

1.8

1.9

1.10

1.12 Loosen yoke retaining clamp (figure 2), remove adhesive material fixing wedges to CRT. Remove wedges completely and clean off dried adhesive from picture tube and wedges. Asmail quantity of “nail polish” has been used to lock the purity convergence rings in place. This seal must be broken with a sharp tipped instrument before any adjustments are attempted. Some models also use a locking ring at either end of the purity and convergence rings. This must be loosened before adjustments are made. It goes without saying that upon completion of all adjustments, the lock must be reset and/or a dab of paint or nail polish must be reapplied to edge of rings to prevent movement. Connect an appropriate signal source, eg: Electrohome RGB generator producting a white field plus individual red, green and blue fields. Bring the long and short purity tab protrusions in line with each other to obtain near-zero magnetic field (figure 4) (In some cases bring the flat and indented tabs together to obtain zero field). Protrusions can then be vertical, horizontal or at any convenient angie to start.

Turn off the green and blue fields and adjust setup controls to produce a red field. (See fig. 3) Pull the deflection yoke back so that a red band appears in the centre of the screen.

Spread the tabs apart as little as necessary and rotate both rings together to center the red band horizontally ‘on the face of the CRT (approximate). (See Fig. 5) Slide the yoke towards the bell of the picture tube slowly to obtain a uniform red field (pure in color) across the entire tube face. Juggle back and forth slightly as necessary. Lightly tighten yoke retaining clamp. Momentarily switch on a cross-hatch signal and rotate yoke to level the pattern on the face of CRT. Return generator to regain red raster. Turn off red field and check for pure field for each of the green and blue fields. Reposition yoke if necessary to obtain optimum purity cn all fields. Tighten yoke retaining clamp to prevent yoke shift or rotation. (Do not instali wedges at this time.) Jf pon rar saoncrs / fea econ cOnMOGnee HAGREYS

Figure 2

CRT SOCKET P.C.B.

SCREEN VR

BLUE CUTOFF ve

GREEN ORIVE GREEN CUTOFF VR

REO DRIVE RED CUTOFF VR

BE CAREFUL OF “B’ ANO 'B'SOOST VOLTAGES PRESENT ON P.C.B. Figure 3

(REAR VIEW]

Long and short ‘Short and long protrusions protrusions

Let the proteusions come inline. Figure 4

Contre Bring the green band to the centre

Page 6

2.0

2.8

3.0

3.2

3.3

3.4

3.5 Static and Dynamic Convergence

NOTE:Staticconvergenceisachievedbyfour

magnets located on the neck, nearest the base of the picture tube, Fig. 2. The middle pair of magnetic rings are adjusted to converge the biue and red crosshatch lines. The.rear pair of convergence rings (closest to the base of the picture tube) are adjusted to converge the magenta (blue/red) to the green crosshatch lines.

Dynamic convergenceisachievedby tiltingthe

defiection yoke up-down and left-right. Ensure that the controls misadjusted during purity setup (screen, cut-off, etc.) are set to give white baiance. See 3.0 below.

Switch generator to the crosshaich pattern. Adjust convergence around the edges of the picture tube by tilting the yoke up-down and left-right, and temporarily install one wedge at the top of the yoke or in a more optimum position. (Figures 8, 9, 10) Turn off green input and turn on the red and blue input. Rotate the 4-pole (middle) pair of magnets as a unit to minimize separation of the red and blue crosshatch lines around the center of the screen (Figure 6). Variation of the angle between the tabs adjusts convergence of red and blue. (Tilt yoke as required to converge red and blue at the edges as in 2.3 above.)

Turn on green input to obtain magenta (red/blue) and green crosshatch lines. Rotate the 6-pole (rear) pair of magnets as a unit to minimize separation of the

magentaandgreenlines(figure7).Varyangle

between the two tabs and further rotate as a unit to finalize.

When converence of 3 colors is optimized (static in center and dynamic around edges) apply stripe of paint or nail polish to converence magnet rings to prevent movement. If applicable, tighten locking ring carefully. Remove temporary wedge from yoke. Tilt yoke in updown and left-right direction for best circumference convergence and install 3 wedges. (It is best to use3. new wedges since they have adhesive backing. Simply pull off tape, slide wedge in place and press outer flap

downfirmly.Formorepermanencyapplysmall

quantity of silastic or similar material at junction of wedges and picture tube. Do not disturb while material is setting. (Order wedges by part number 38-1233-01).

White Balance (Grey Scale Tracking) Refer to figure 3. Do the following in subdued light:

Note this adjustment can be accomplished with no signal connected; eg: input connector open or if a signal generator is connected, switch off all 3 inputs at the generator. Set red and green drive controls to their mechanical center and turn the common G2 screen control and 3 cut-off controls to minimum (fully counterctockwise). Slowly turn up G2 screen control until the color appears, then back off to edge of vi tly. Do not touch the associated cut-off control - it should stay fully CCW for the remaining set-up. Slowly turn up the other two color cut-off controls in turn to match the first. This should resultin the faintest grey. Turn on the signal generator with all 3 inputs on. (a crosshatch pattern would be appropriate). [FRONT VIEW)

Let the red and blue lines come in line by turning two 4-pole magnets.

[FRONT VIEW]

=

Let the green and magenta inex come in ine by turning two 6-pole magnets. Figure 7

[REAR VIEW]

Del. yoke

Roughly adjust the circumferential convergence and install one wedge temporarily Figure 8

[FRONT VIEW] Red Green Blue

Blue Green Red Tilting the yoke upward will move the lines as shown with the arrows, Figure 9

(FRONT VIEW) Greeny

Titting the yoke to the right will move the lines as shown with the arrows. Figure |

Page 7

3.6 Adjust the red and green drive controls for “neutral white” on high white picture areas. Generally these controls will be left at mech. centre.

3.7. Note: When monitor is re~connected with the game the screen control (G2) may require a slight adjustment to obtain proper black level. (the black portion of picture just extinguished).

{REAR ViEW] ‘Anode cap

Figure 11

4.0 Power Supply The regulated +B1 control (R909) has been factory adjusted and normally requires no adjustment. However, if any repairs have been made to the chassis it is recommended that this adjustment should be made.

  • Allow 5 minutes to warm up.
  • No signal applied.
  • Connect an accurate D.C. voltmeter to TP-91 or the emitter of X04 power regulator transistor.
  • Adjust R909 for 120V. (See fig. 1)
Note: Should +B1 control be set too high, it may cause possible component damage. Use an accurate D.C. voltmeter to set B1 (Bt).

5.0 Focus

Adjust focus control for best overall definition and picture detail an average signal applied. (Highlights should be favoured.)

6.0 Color Service Generator for G07 Monitor

Electrohome has developed a color service generator that is specifically designed for use with the G07 color data monitor. It provides the monitor with both horizontal and vertical sync, as well as the following test patterns:

  • Fine cross-hatch pattern
  • Broad bar cross-hatch pattern
  • Complete field Three color selection switches, red, green and blue, provide the ability to display the above patterns in the three primary colors as well as the three secondary colors. This product may be ordered from: Contracts Marketing ELECTROHOME Electronics 809 Wellington St. North Kitchener, Ontario Canada N2G 4J6 Telephone: (519) 744-7111, Ext. 567 7.0 X-Ray Emission Check 7.1 Assure the power supply B1 is properly adjusted to 120V DC. See Item 4.0 (page 8) 7.2 Assure that the anode voltage does not exceed max. as per Item 2.0 page 4.

7.3 Assure that the high voltage hold down circuit is operating correctly. Use the following procedure.

  • Increase the B1 greater than 138.5V by shorting collector/emitter of the power regulator, X04.
  • Observe that the anode voltage (EHT) goes to 0. if the EHT does not go to 0, a fault must be located and repaired.
  • Remove short and set should return to normal operation. (Note, after the short is removed some monitors may not restart. In this case, remove power from monitor momentarily and normal operation will be restored.
Note: The protector circuit consists of the components shown below in Fig. 13 with acircuit description.

rn Ter xm Eto mete

1.88 Kohn tole Ginx S701 300/18 4.7 Koha

Figure 13

8.0 Circuit Diagram and Description of High Voltage Hold Down or Safety Circuit

8.1 Circuit Diagram of High Voltage Hold Down Circuit.

8.2 Operation of High Voltage Hold Down Circuit. The high voltage hold-down circuit protects the high voltage circuit from dangerous voltage with short circuiting between emitter and collector of power regulating transistor. The base voltage of X701 is increased when the B1 voltage is increased more than 138.5 V DC.

When the base of X701 is increased, a short is produced by X701 between pin 11 and ground of IC 501, shutting down the horizontal osc. and high voltage.

Page 8

SWITCH ADJUSTMENTS

PROGRAM NO. 1

METHOD OF PLAY

Sw. 1 SW. 2

1 COIN = 1 PLAYOFFOFF
2 COINS = 1 PLAYONOFF
1 COIN = 2 PLAYSOFFON
FREE PLAYONON

BONUS GALAXIP

Sw. 3 SW. 4

NO BONUS GALAXIPOFFOFF
BONUS GALAXIP AT 4000 PTS.ONOFF
BONUS GALAXIP AT 5000 PTS.OFFON
BONUS GALAXIP AT 7000 PTS.ONON

NUMBER OF GALAXIP PER GAME

Sw. 5 3 GALAXIP PER GAME OFF 5 GALAXIP PER GAME ON

M051-00866-A006

PROGRAM NO. 2

METHOD OF PLAY

sw. SW.2

1 COIN=1 PLAYOFFOFF

2 COINS = 1 PLAY on OFF

1 COIN =2 PLAYSOFFon
FREE PLAYONON

BONUS GALAXIP

Sw.3 sw. 4

NO BONUS GALAXIPOFFOFF
BONUS GALAXIP AT 3000 PTS.ONOFF
BONUS GALAXIP AT 4000 PTS.OFFoN
BONUS GALAXIP AT 6000 PTS.ONON

NUMBER OF GALAXIP PER GAME

SW.5 2 GALAXIP PER GAME OFF

  • GALAXIP PER GAME ON

MO51-00866-A005

Page 9

NOTES

This space is provided for personal notes

Page 10

NO. 869 — GALAXIAN COCKTAIL — PICTURE

sntHOgs

1UP_ HIGH SCORE

ake ie oe ee se | Ss Ai tie OS ie Ne ie ty

MIDWAY MFG. CO. ABALLY COMPANY

Page 11

NO. 869 — GALAXIAN COCKTAIL — PICTURE

ORDER BY PART NUMBER ONLY [ITEM] PART NO DESCRIPTION

0017-00003-0308 0869-00907-0000 0869-00902-0000 0869-00905-00XF 0775-00104-00XF 0017-00101-0117 0869-00906-0000 0869-00906-0100 0017-00101-0341

A090-00058-0000 0090-00002-01BK 0017-00101-0555

0017-00102-0048 0017-00103-0026

A749-00003-0000 A623-00013-0000 A625-00024-0000 0625-00117-0000 0017-00101-0628 0017-00103-0008 A749-00005-0000 0017-00101-0028 A869-00010-0000 A869-00010-0100 0869-00901-0000 0017-00101-0672 0017-00104-0004 0017-00103-0010 A627-00066-0000 0017-00101-0017 0869-00504-0000 MONITOR W/CHASSIS — ELECTROHOME PLEXI — 15” x 18-3/4” T.V. BEZEL GLASS TOP — 32” x 22” x 1/4” GLASS CLIPS (8 REQ’D.) #8 x 5/8 PHL. TRUSS HD. S.M.S. (16 REQ'D.) SHELF OVERLAY — PLAYER #1 SHELF OVERLAY — PLATER #2 #6 x 1/4 PHIL. TRUSS HD. M.S. — MTG. SCREWS (4 REQ’D. PLAYER #1, 4 REQ’D. PLAYER #2) FRONT DOOR ASSY. W/COIN METER COIN DOOR FRAME #6 - 32 x 5/16 SLT. HEX HD WD SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) LEG LEVELERS (4 REQ’D.) LEG LEVELER NUTS (4 REQ’D.)

ADDITIONAL PARTS COIN BOX ASSY. COIN BOX COVER ASSY. COIN BOX GUIDE BRKT. ASSY. COIN BOX GUIDE #8 - 32 x 3/4 CARRIAGE BOLT (4 REQ'D.) #8 - 32 HEX NUT (4 REO’D.) INTERLOCK SWITCH ASSY. #8 x 3/4 HEX HD. S.M.S. (6 REQ'D.) MONITOR SUPPORT B & WELD NUT ASSY. MONITOR SUPPORT A & WELD NUT ASSY. HINGE (CABINET TOP) #10 -32 x 1-1/4 CARRIAGE BOLT (8 REQ’D.) #10 WASHER (8 REQ’D.) #10 - 32 HEX NUT (8 REQ’D.) ON-OFF SWITCH ASSY. #6 x 1/2 HEX HD. S.M.S. (6 REQ’D.) WOOD PEDESTAL — OPTIONAL

MIDWAY MFG. CO. A BALLY COMPANY

Page 12

NO. 869 — GALAXIAN COCKTAIL — INTERIOR ACCESS PICTURE

MIDWAY MFG. CO. A BALLY COMPANY

Page 13

NO. 869 - GALAXIAN COCKTAIL — INTERIOR ACCESS PICTURE

ORDER BY PART NUMBER ONLY firem] Part Ne 0017-00003-0308 A869-00007-01XF A869-00007-00XF 0017-00101-0769 0017-00009-0033 0017-00101-0026 0610-00132-0000 0017-00101-0028 A084-91352-C869 A082-91365-B000 A084-91353-A866 0624-00902-0300 0624-00902-0500 0624-00902-0100 0017-00101-0028 0017-00104-0031 A869-00011-0000 0017-00003-0187 0017-00009-0343 0017-00101-0642 0017-00101-0118 0017-00103-0061 A869-00015-0000 A869-00014-0000

0017-00003-0222 0775-00110-00XF 0749-00106-00XF 0017-00101-0347 0017-00104-0009 0017-00103-0005 0017-00101-0026

0017-00003-0310 0017-00009-0485 0869-00909-0000 0870-00700-00XF 0017-00101-0583 0017-00103-0052 0017-00104-0019 DESCRIPTION ELECTROHOME MONITOR W/CHASSIS MONITOR SUPPORT ASSY. R.H. MONITOR SUPPORT ASSY. L.H. #10 x 3/4 SLOT HEX HD. S.M.S. (8 REQ'D.) BASSICK CLAMP (2 REQ’D.) #8 x 5/8 HEX HD. S.M.S. (4 REQ’D.) STRIKE (2 REQ’D.) #8 x 3/4 HEX HD. S.MS. (4 REQ'D.) GAME LOGIC BOARD ASSY. FILTER BOARD ASSY. MEMORY BOARD ASSY. P.C. SUPPORT BRKT. - 2-1/2” (2 REQ'D.) P.C. SUPPORT BRKT. - 6-1/2” P.C. SUPPORT BRKT. - 12” (2 REQ'D.) #8 x 3/4 HEX HD. S.M.S. (12 REQ’D.) #8 WASHER (12 REQ’D.) TRANSFORMER BOARD ASSY. 6x 9 SPEAKER 8 OHM, 9V. SPEAKER GRILL (3 REQ’D.) #8 - 32 x 1-1/2 CARRIAGE BOLT (4 REQ'D.) #8 - 32 x 1-1/8 CARRIAGE BOLT (8 REQ’D.) #8 - 32 HEX NUT SEMS. (12 REQ’D.) MASTER CABLE ASSY. COIN DOOR CABLE ASSY. FAN ASSY. FAN FAN PLATE VENT SCREEN #6 - 32 x 1/2 PHIL. R.H.M.S. (4 REQ'D.) #6 EXT. WASHER (4 REQ'D.) #6 - 32 HEX NUT (4 REQ'D.) #8 x 5/8 SLOT. HEX HD. $.M.S. (4 REQ’D.) SUBSTITUTE FAN ASSY. — DOMESTIC EXHAUST FAN 115V. 60 HZ FAN FINGER GUARD FAN SHROUD FAN SPACER (4 REQ'D.) #6 - 32 x 1-1/4 CARRIAGE BOLT (4 REQ’D.) #6 - 32 LOCKNUT (4 REQ'D.) #6 FLAT WASHER (4 REQ'D.) MIDWAY MFG. CO. A BALLY COMPANY

Page 14

. PAGE 12 NO. 869 — GALAXIAN COCKTAIL — CONTROL SHELF ASSY.

Page 15

et a NO. 869 — GALAXIAN COCKTAIL - CONTROL SHELF ASSY.

ORDER BY PART NUMBER ONLY

A869-00002-00XF A869-00002-01XF 0017-00100-0025 0017-00104-0028 0017-00103-0054 0775-00105-00XF 0017-00009-0376 0010-00593-0000 0017-00009-0384 0586-00036-0000 0020-00202-0000 0017-00101-0522 0017-00101-0525 A775-00005-0000 0020-00240-0010 0775-00101-00XF 0017-00101-0517 0017-00104-0009 0017-00101-0720 0775-00701-00XF 0775-00902-0000 0017-00100-0015 0017-00100-0050 A869-00006-0000 0775-00100-00XF 0017-00101-0014 0017-00031-0044 0017-00003-0219 0869-00904-0000 0017-00032-0051

A869-00012-0000 A869-00013-0000 SHELF PLATE ASSY. — PLAYER #1 SHELF PLATE ASSY. — PLAYER #2 1/4 E-RING FLAT WASHER (2 REQ'D.) PAL NUT SPACER HOUSING SPRING BUTTON PUSH BUTTON SWITCH ASSY. SWITCH PLATE (3 REQ’D.) #5 - 40 x 7/16 RD. HD. M.S. (2 REQ’D.) #5 - 40 x 9/16 SLOT. RD. HD. M.S. (4 REQ’D.) SWITCH ASSY. (2 REQ'D.) TENSION LEAF .010 (2 REQ'D.) SWITCH MTG. BRKT. #5 - 40 x 1/4 SLOT PAN HD. M.S. (2 REQ’D.) #6 EXT. LOCKWASHER (2 REQ'D.) #10 - 32 x 3/4 SOCKET HD. CAP SCREW POST ROLLER 5/32 E-RING 1/2 E-RING (2 REQ’D.) KNOB & SHAFT ASSY. SHELF MTG. BRKT. (2 REQ'D.) #6 x 1/2 SLOT HEX HD. M.S. (5 REQ'D.,) LAMP SOCKETS (2 REQ'D.) #194 WEDGE LAMP 14V., .27A. LIGHT SHIELD — 3 x 11-5/32 BUTTON SWITCH (PLAYER #1 ONLY) (2 REQ’D.) NOT SHOWN PLAYER #1 CONTROL CABLE ASSY. PLAYER #2 CONTROL CABLE ASSY.

MIDWAY MFG. CO. A BALLY COMPANY PAGE 13

Page 16

NO. 869 — GALAXIAN COCKTAIL — TRANSFORMER BOARD ASSY.

® 6

( .

o/ KN. 4 \ D

  • ~—® Ai @ @ °

MIOWAY MFG. CO. ‘A BALLY COMPANY

Page 17

NO. 869 - GALAXIAN COCKTAIL — TRANSFORMER BOARD ASSY.

ORDER BY PART NUMBER ONLY [mem[paRy ne | ———=iESERIPTION. —————SC—*d MT00-00085-0000 TRANSFORMER — 115 VOLT, 50 HZ. MT00-00084-0000 TRANSFORMER — 240 VOLT, 50 HZ. 0017-00003-0114 NOISE FILTER A031-00002-0000 TERMINAL STRIP ASSY. 0064-030XX-XXPX| IN4004 400V. DIODE 0720-00001-0300 3 POSITION FUSE CLIP 0017-00003-0261 FUSE 1.5 250V. — SLO BLO (2 REO’D.) 0017-00003-0005 FUSE 2A. 250V. 0720-00001-0400 4 POSITION FUSE CLIP 0017-00003-0169 FUSE 5A. (2 REQ'D.) 0017-00003-0001 FUSE 1-1/2A., 250V. (2 REQ'D.) 0017-00101-0637 #8 - 32 x 1-1/4 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0008 #8 - 32 HEX NUT (4 REQ'D.) 0017-00101-0014 #6 x 1/2 SLT. HEX HD. WD. SCR. (12 REQ’D.) 0017-00101-0018 #6 x 3/4 SLT. HEX HD. WD. SCR. (4 REQ’D.) A866-00049-0000 LINE CORD ASSY. — NOT SHOWN DONMMPWNH

MIDWAY MFG. CO. ‘A BALLY COMPANY PAGE 15

Page 18

NO. 869 — GALAXIAN COCKTAIL — FRONT DOOR ASSY.

NOTE:

MIDWAY'‘S BASIC COIN DOOR,

VARIATIONS ARE DEPENDANT ON

YOUR PARTICULAR GAME.

Page 19

NO. 869 — GALAXIAN COCKTAIL — FRONT DOOR ASSY.

ORDER BY PART NUMBER ONLY

0017-00101-0552 0090-00117-03XF A090-00058-0000 0017-00005-0050 0090-00002-01BK 0017-00005-0041 0090-00901-0000 0090-00126-01XF 0017-00101-0528 0090-00903-0040 0090-00143-0000 0017-00104-0002 0017-00007-0019 0017-00103-0005 0090-00 104-0000 0017-00101-0598 0010-00181-0100 0090-00129-00XF 0010-00134-0000 0090-00008-0000 0093-00155-00XF , 0017-00100-0012 0093-00151-00XF 0090-00005-0000 0017-00101-0555 0017-00005-0039 0010-00557-2500 0017-00007-0132 0017-00101-0507 0090-00128-00XF A090-00061-0000 WOON ODOFPWN —

A090-00064-0000 DESCRIPTION

#6 - 32 x 1/4 CARRIAGE BOLT (2 REQ'D.) COIN ENTRY PLATE (25¢) DOOR ASSY. SINGLE ENTRY DOOR LOCK & KEY WITH SCREW & NUT SINGLE DOOR FRAME 421 N.S. CAM DOOR SWITCH SWITCH BACKUP PLATE #5 - 40 x 3/4 LONG M.S. (2 REQ'D.) 25¢ WINDOW COIN PLEX RETAINER SPLIT LOCK WASHER (2 REQ’D.) KEY HOOK #6 - 32 HEX NUT (2 REQ’D.) TOP & BOTTOM COIN CHUTE W/BRKT. ASSY. #8 - 32 x 5/16 SCREW (4 REQ'D.) SPRING PIVOT POST SPRING ACCEPTOR FRAME ASSY. REJECTOR LEVER E-RING COIN GUIDE MTG. BRKT. COIN GUIDE ASSY. #6 - 32 x 5/16 SCREW (2 REQ’D.) COIN SWITCH TRIP WIRE PUSH-ON RING (BLK) #4 - 36 x 3/4 SCREW (2 REQ’D.) SWITCH BRKT. — DOOR TILT (NOT USED) ANTI-STRING DEVICE ASSY. — OPTIONAL (REPLACES ITEM 24) ANTI-PENNY DEVICE ASSY. — OPTIONAL

MOMAr acme OF PAGE 17

Page 20

COMPONENT LAYOUT PART NO. MO5I-00866- 8002

H INDICATES O.1MF. S0¥. ARIAL LEAD CERAMIC CAR. ao ao 2 3 4 5 6

oo ao a

= 2068-o4axx-aBxx HER Sank fal 7a.sed 741586 vasied ——rasieg] of] frais30a| [Jee RA brassoa] Be "ALSO SR 7AS6I gi 7ALSI6I a ()e be=¢ iu FASB wae ALSi| 7ALSI6I ALSIS "kg ioes ead ALSO 74.520 74.510 | basta) HLS377 | ‘Cie

. PAL SOB bras20 prisees puiseas] S02]

= pmus273 ALSO H

i L ALSI84 basir miS273 | — bRaLS367| pMsay

ae an x |e basa ALSIT| | be2K "eo Fa uma |B \ mS ! Ltd

J ALSIO4 ALSIS? p 826 Son 8216

meee.) 12 7 9 Hie ALSIO4 yon a oz 55 ss

. 1 F Ree Ee LSS? meas, | 1a mene 38 oo 24 BIN SocKET SSNs ae Sesest-108 fl m i r---- Gp BARABABRBBB BR MeO

gg Lote ed € pMLS368 ALSIS7 ALSIS7 | ALSIS?7 ALSIS7 ALS367 7.589 | > fase LSE | ALS ALSO ALSO] frase] AL SEH fras367|

c fas] GREER 7420 LSS 74% 7474 8 Smse4 fuszes) — brasee 74LSB6 7ALS86 FLS86 Z80A i i

Eee ee a

ee A FaLsie4| prars3o] MLSEI 74.516 7ALSI6t | 7ALSt6! | GAME LOGIC BOARD

  • P.C. A082-91352—8-VERSION = re

aa

Page 21

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 22

NOTES

This space is provided for personal notes

Page 23

i i] ay asv tee 24 ae Yop Bie ow | 20 20|—— <8 Tl

or ter] : eae ae

asice/912z

asics /oice

esie6/9icz

avie6/oicz iv Lr

J] os

Iss CONNECTOR CONNECTON TO Loc. 7F To Loc. 7

Be

iD

I

MEMORY LOGIC SCHEMATIC

PART NG, MOSI- 00866-4004

MEMORY BOARD

CIRCUIT

Page 24

MoniToR. INTERFACE

aR ve, Eogtten TAR

1 Ton outer THE | Nt | bee dag Leap ta ae ec | uct ome, CE sgee poe

GAME LOGIC BOARD PC. A082-91353-A/B866

WIRING SCHEMATIC PART NO. MO5!-00869- ADO3,

ruse.

sy

‘ \ -oFF ‘sf eorl

‘SAFETY cis 4 a s GALAXIAN" COCKTAIL. TABLE MODEL. Mq-05 FORMER lay Jrunne MIDWAY MFG. CO. 10750 W. GRAND AVE, . vo com boon FRANKLIN PARK, ILL. 6013/ a we SSRs,

Page 25

VIDEO INTERFACE PCB

vor ovata TT ee

  • << trem $u-11924(7)

@ SCHEMATIC NOTES UNLESS OTHERWISE SPECIFIED RESISTANCE : (1) ( K-+K.1Ly M—>M 1), 174 (W) CARBON RESISTOR CAPACITANCE: 1 OR HIGHER—*( pF), LESS THAN 1 —+(wF) WORKING VOLTAGE —*50 (Vv) CERAMIC CAPACITOR INDUCTANCE + (pH) ELECIROLYTIC CAP: CAPICTANCE VALVE LyF)/ WORKING VOLTAGE (V), NP —» NON -POLAR (OR BIPOLAR) ELECTROLYTIC CAP SU4132A MAIN PCB

j3073|REFER TO THE PARTS LIST FOR ADDITIONAL COMPONENT
{wwcur3034~—INFORMATION.
133

Q INDICATES TEST POINT CONNECTION

att ie ane Ce

H@)ry INDICATES CHASSIS GROUND UNLESS OTHERWISE

‘| sat SPECIFIED

HTeter!oe, |cseodFeeue-
|TR"AHz INDICATES CYCLES PER SECOND

FOR SAFETY FURPOSES (AND CONTINUING RELIABILITY) AX REPLACE ALL COMPONENTS MARKED WITH SAFETY SYMBOL WITH IDENTICAL 1YPE

NOTE : FR—*FUSIBLE RESISTOR -—WH— Be [x rao) Sor

PARTS IDENTIFICATION ON CIRCUIT BOARDS :

e.g. SU1126A (R107 = R1107) SU3C30A (R113 * R3113) “ oe 2 * DEFLECTION YOKE i

x701 25 yor our te su-sosra PROTECTOR qd

|power Ree baveioSCHEMATIC PART NO. MOSI-O0087-A006
==00-4147-Q2

| ISOLATION TRANSFORMER MUST ISSUE 1 i BE USED. L [ame i a LeSe cove _nguon 0 rt 2 an all Prema a ___(00-4147-03_]

Page 26

GALAXIAN LOGIC BOARD

CHIP NUMBER FUNCTION

74LS00 Quad Two Input Nand 74LS802 Quad Two Input Nor 7404 Hex Inverter

74LS08 Quad Two Input And 74.810 Triple Three Input Nand

74LS20 Dual Four Input Nand

74LS30 Eight Input Nand 74LS32 Quad Two Input Or 74LS74 Dual “D” Flip — Flop

T4LS86 Quad Two Input Exclusive Or 74LS107 Dual “JK” Flip — Flop 74LS8138 Three to Eight Line Decoder 74L8139 Dual Two to Flour Line Decoder

74LS157 Quad Two Input Multiplexer

7418161 Four Bit Counter

74LS163 Four Bit Counter

T4LS164 Eight Bit Shift Register

74L8174 Hex “D” Flip — Flop

748175 Quad "D” Flip — Flop

74/8194 Eight Bit Shift Register

74LS259 Eight Big Addressable Latch

74L8273 Octal “D” Flip — Flop

74LS823 Four Bit Binary Adder

748245 Octal Bus Transceiver

74LS366 Hex Bus Driver — Inverting

74LS367 Hex Bus Driver

T4LS368 Hex Bus Driver — Inverting

748377 Octal “D" Flip — Flop

Page 27

CHIP NUMBER

7418393

271800

2114

TMS4045

M9124

2102-2

AMg101

8304

8216

LM324

LM377

z80

1M5610

78GUIC

ULN2075

18.432

cp4066

pa4vm4

GE6015

MC 14066

GEAISF

ANGE

1N4148

IN4736A

D2316EC

D2364C GALAXIAN LOGIC BOARD

FUNCTION

Dual Four Bit Binary Counter

Ram

Ram

Ram

Ram

Ram

Ram

Bus Driver — Bidirectional

Bus Driver — Bidirectional

Quad Operational Amp

Timer

Audio Amp

CPU

Prom — 16K

Prom

Voltage Regulator

Quad Buffer

X-TAL

Quad Electronic Switch

Transistor

Transistor

Quad Electronic Switch

Diode — Rectifier

Diode — Rectifier

Diode — Rectifier

Diode — Zener

16K Rom

64K Rom

Page 28

NOTES

This space is provided for personal notes