CATHODE RAY TOMES

Crash (July 1979)

Crash (set 1) (Exidy, 1979) · Document · 29 pages · 27 sections · original scan

Page 1

¥ | <a July 1979 ES irc. (c) 1979 EXIDY, Inc. Ss

Page 2

CONTENTS

LT. GENERAL 2c eee c ec ccc cece cee cere eect cence cc cetee

II. NORMAL OPERATION

A. Attract Mode ...-........ B. Introduction Mode ....... C. Game Play ........-...---

III. SELECTABLE OPTIONS

A. Coinage ......... B. Crashes (Turns) C. TOP THIS SCORE ..

IV. AUDIO ADJUSTMENTS ..

V. POWER SUPPLY ADJUSTMENTS .......eeeeereeeecceceeee

VI. MECHANICAL ASSEMBLIES

A. To Service Early-Production Control Panels ... B. To Service Late-Production Control Panels .... C. To Service the Four-Way Joy Stick .....-....-. D. To Remove the Monitor .......e eee cece eee e eee E. To Remove the Logic and Audio Boards .........

VII. TECHNICAL INFORMATION

A. Logic Description and Operation ........-eeeee B. Audio Description and Operation ....... C. Diagrams, Pinout Table, and Schematics ....... Saf

(OkOmel

oy ocoMMaN

Page 3

ILLUSTRATIONS

Figure 1: Monitor Display ........ cece eee eee cece eee

Figure 2: Audio Board Adjustments ...-.eseeeeeeeeeee

Figure 3: Power Supply Adjustments ........eeeeeeeee

Figure 4: Control Panel (Early Production) .........

Figure 5: Control Panel (Late Production) ..........

Figure 6: Four-Way Joy Stick ...... ccc ccc ccc eee eee

Figure 7: Major Internal Components ........---2-.00-

Figure 8: Logic Board Block Diagram .....-+ee-e-eeeee

Figure 9: Audio Board Block Diagram .......+-ee-eees

Figure 10: Harness Diagram ....... cece eee cece cece ene

Page 4

I. GENERAL

CRASH is a one or two player skill game in which players drive a car around a five lane square track while avoiding collisions with computer controlled drone cars. Players score points by driving over speed dots marked on the traffic lanes; players avoid collisions by changing lanes at the four traffic interchanges, and by using the FAST button to beat drone cars to interchanges.

PLAYER CRASH has three coinage options. After the player inserts his coins, play instructions and the day's high score appear on screen. An optional TOP THIS SCORE feature gives a replay to the player who beats a random score.

The operator selects the number of crashes (turns) per play: 2, 3, 4, or 5.

DRIVING

Figure 1:

1 Traffic lane 2 Interchange 3 Speed dot Monitor Display

4 player car 5 Drone car 6 Message panel

Page 5

II. NORMAL OPERATION

A. Attract Mode

When the game is first turned on, the words GAME OVER will flash on screen. Also on screen will be TODAY'S HIGH SCORE followed by a score which changes with each new higher score attained throughout the day. When the game is turned off, the high score is reset to zero.

Also displayed on screen, at the operator's selection, will be one of the following:

COIN PLAY

or

COIN 1 we eeeee 2 cece cee eee eeeeeee 2

or

COIN PLAY 2 cecccerccccecceee 1 4 cecccccccccsccves 2

CRASH also has a coin accumulator (credit counter) so that a player can buy a number of games in advance.

While in the attract mode (no credits, no game in progress) the game plays automatically.

B. Introduction Mode

When a player deposits a coin, the following message comes on screen:

CHANGE LANES TO AVOID CRASH WITH OTHER CARS

10 POINTS FOR EACH DOT BONUS POINTS IF ALL DOTS ARE ELIMINATED

CREDITS N

TOP THIS SCORE FOR CREDIT

M Here, N is the number of games in the credit counter, and M is a random score used by the TOP THIS SCORE feature. At the operator's option, CRASH awards one extra game to any player who matches or exceeds the score M.

Cc. Game Play

When a player presses one of the two START buttons (after coinage), a fanfare tune signals the start of play. The player's car starts at the bottom center of the screen (in the outer lane) and moves counterclockwise. One drone car starts at the same place, moving in the opposite direction.

The drone car tries to crash into the player's car. The player must avoid crashes by changing lanes at interchanges; he uses the FAST button to reach an interchange before the drone car.

When the player's car drives over a speed dot, the SPEED BEEP sounds and the dot disappears. At game start, each dot scores 10 points; if the player clears all the dots in a single turn (without crashing into the drone car) the playfield is reset, and all speed dots score 20 points. Each successive time the player clears all dots, the dot score goes up: 20 points, 30 points, etc.

The number of drone cars increases with the point value of the speed dots. At game start (10 points per dot) only one drone opposes the player; at the next level (20 points per dot) two drones oppose him. At all succeeding levels (30 points and above), three drones.

A turn continues until the player crashes into a drone car. The mes— sage display in the center of the screen shows turns remaining, by displaying one car for each crash (turn) left, not counting the current turn.

Page 6

III. SELECTABLE OPTIONS

CRASH has three switch selectable VOLUME -- 1 pot: options. These are controlled by a seven segment DIP switch located on R66=overall volume the main logic board at position 14A (see Figure 2, item 6). This CRASH -- 1 pot: switch is acccessible from the front of the game though the coin R29=volume door. SPEED BEEP -- 1 pot: Following are the options and the switch settings for their selec- R39=volume tion: SKID -- 2 pots: A. Coinage switch switch

45R47=frequency
2 Player - 1 CoinONONR49=volume
1 Player - 1 CoinONOFF

2 Player - 2 Coin

1 Player - 2 CoinOFFON

2 Player - 4 Coin

B. Crashes (Turns) switch switch 6 7

2 CrashesONOn
3 CrashesONOFF
4 CrashesOFFON
5 CrashesOFFOFF

C. TOP THIS SCORE earch

Credit awarded for OFF topping score

~-Credit not awarded ON for topping score

IV. AUDIO ADJUSTMENTS (Figure 2)

MOTOR -- 3 pots:

R52=high frequency

R53=low frequency Figure 2: Audio Board Adjustments

R16=volume 1 R52 MOTOR 6 DIP SWITCH 2 R53 MOTOR 7 R39 SPEED BEEP

MUSIC-- 1 pot:3 R63 MUSIC8 R49 SKID

4 R66 VOLUME 9 R47 SKID R63=volume 5 R29 CRASH 10 R16 MOTOR

Page 7

POWER SUPPLY ADJUSTMENTS

Connect a voltmeter to the +5 and ground traces on the logic board. 2, Adjust the power supply potentiometer for +5.0 + .1 VDC (see Figure 3).

Adjustment potentiometer

Figure 3: Power Supply Adjustments

Page 8

VI. MECHANICAL ASSEMBLIES

NOTE

Each CRASH game has one of two control panels:

  • A single metal plate, held by four carriage bolts (early production).
  • A large metal plate, hinged at the bottom (late production).

A. To Service Early Production Control Panels (see Figure 4).

  • Unplug power cord. Open the coin door.

Reaching up through the coin door, remove the wingnuts from the four carriage bolts that hold the control panel down.

Lift the control panel up from the cabinet and set it on edge, so that you can reach its underside.

Check all terminal connections to the pushbuttons and the fourway joy stick.

Figure 4:

1 Carriage bolt 2 Start buttons 3 FAST button Control Panel (Early Production)

4 Control panel 5 Four-way control 6 Control harness

Page 9

To Service Late Production Control Panels (see Figure 5)

Unplug the power cord.

Open and remove the back door.

From inside the cabinet, remove the three control panel nuts (see Figure 7). 4.

5. Open the coin door.

From the front of the cabinet, pull the control panel out and down; let it rest on the open coin door (see Figure 5).

Check all terminal connections to the pushbuttons and the fourway control.

Control Panel (Late Production) Figure 5:

1 Control panel 4 Main harness 2 Start buttons 5 Four-way control 3 Control harness 6 Control stick 7 FAST button

Page 10

C. To Service the Four-Way Joy Stick

The four-way joy stick is mounted on the control panel with four long screws and standoff spacers. Four pairs of spring steel cup washers surround the control stick, between the control panel and the top plate (see Figure 6). These cup washers bear against a disk welded to the control stick, and push the stick towards its center (rest) position. Four leaf switches on the bottom plate (activated by the control stick) signal lane changes to the logic boad.

Figure 6: Four-Way Joy Stick

1 Carriage bolt 8 Kep nut 2 Control stick 9 Switch plate 3 Control panel (bottom plate) 4 Flat washer 10 Kep nut (small 5 Cup washer pattern) 6 Spacer 11 Leaf switch 7 Lower disc 12 Phillips screw (top plate) service the control:

Unplug the power cord.

Open the control panel (see above).

Check the harness connectors to each leaf switch.

Check the throw of each micro~ switch; the control stick should activate, but not bottom-out against, each switch.

If necessary, adjust leaf switch throw by carefully bending the switch actuator with a long-nose pliers.

Page 11

5. To Remove the Monitor

Unplug the power cord.

In some cabinets, the monitor is not accessible through the back door. A monitor access panel above the back door is secured with four wood screws.

Open and remove the back door or monitor access panel.

Unplug the harness connector from the monitor.

Remove the four bolts from the monitor chassis flange mounts.

  • Lift the monitor up and slide it out of the cabinet.

E. To Remove the Logic and Audio Boards

  • Unplug the power cord.
  • Open and remove the back door.
  • Clip the plastic tie wraps which hold the boards in their rack.
  • Disconnect the edge connector from the logic board.
  • Slide the boards out of their rack.

Figure 7: Major Internal Components

1 Monitor 2 Power supply 3 Speaker 4 In-line fuse 5 Interlock switch 6 PC boards 7 Cash box 8 Coin door

Page 12

VII. TECHNICAL INFORMATION

A. Logic Description and Operation (see Figure 8)

CRASH uses the 6502 central proces-— sor unit. (For more information on this procesor, refer to MOSTEK publication #6500-10A, MCS Microcomputer Family Hardware Manual.)

This processor is unique in that it does not have a separate input/output structure, but treats all I/0 as if it were an area of memory. Memory is mapped as follows:

FFF 8-FFFF Interrupt and reset vectors FQOO-FFF7 Program storage (PROM) DO0O Four-way control and interrupt reset co0o0 Option switches (input) A000 Control switches (input) 8000 Player car rotation and audio control bits (outputs) 4000-43FF Screen RAM 3000 Player car horizontal position (controls) 2000 Player car vertical position (controls) 1000-1FFF Program storage (PROM) 0100-01FF Stack RAM 0000-O00FF Base page RAM

Base page RAM holds variables while the game program is running; the stack RAM holds return addresses and important data during subroutines. The program storage PROM holds the program which controls the operation of the game.

The screen RAM consists of 1024 bytes (8-bit words) of read/write Memory. When not being addressed by the processor, this RAM is scanned by main timing, to display a 32 x 32 matrix of squares on the screen. The data stored in the scren RAM is then used to select one of 256 images from the screen ROM (each image is 8 elements wide and 8 lines tall). Note that the processor never addresses screen ROM directly (see Figure 8).

The 8 x 8 images selected from screen ROM fit together to form the display on screen. An alphanumeric character consists of a single 8 x 8 image, while the player's car and the crash explosion are each made up of several images.

Example:

To store the letter "X" in the upper left corner of the screen, the processor would write 29H in memory location 4000H.

The player car is generated by two sets of counters (horizontal and vertical) which are used to position the image on screen. The outputs of the counters, along with the rotation information in 8000H, are fed to the player car PROM to form the car's image. The processor controls the car by preloading the counters to the desired position during vertical sync.

The processor reads data from the switches by gating the data from the control or option switches onto the data bus when the appropriate address is selected.

B. Audio Description and Operation (see Figure 9)

The audio board is powered by +5 vpc from the logic borad and +15 vpc developed on the audio board itself. The AC power source for the +15 VDC comes from an external transformer which steps down the 115 VAC line voltage.

The audio board contains the following circuits:

  • +15 VDC regulated power supplies
  • audio amplifier
Page 13
  • white noise generator
  • speed beep sound generator
  • crash sound generator
  • skid sound generator
  • motor sound generator
  • music input
  • yoke polarity driver

Following are brief descriptions of these circuits:

The +15 VDC Power Supply

The first stage of the +15 VDC supply is a full wave rectifier which converts the input 35 VAC (centertapped) to approximately +25 VDC. This later DC voltage is not critical, however, and may vary from transformer to transformer.

The second stage is a self-contained 3-lead regulator chip (LM 340T - VR1) which converts the +25 VDC to +15 VDC. This +15 VDC source feeds most audio circuits, and the base of transistor Q1. This source is a relatively low current supply, so pass transistor Q1 provides a higher current at +15 VDC for the audio amplifier chips (LM 380N or equivalent). Transistor Q1 is configured as an emitter follower, so the emitter voltage will equal the regulated +15 VDC minus approximately .7 VDC (the normal drop across the base-emitter junction for a silicon transistor at or near saturation).

The White Noise Generator

The white noise is produced by the thermal breakdown of a transistor junction. Q2 has a grounded base, an open collector, and an emitter tied to the +15 VDC current source. The base-emitter junction is reverse biased so much that it breaks down, generating broad band noise. U1 amplifies Q2's output. Ul1's output is a high impedance current source and would be easily loaed down by other audio circuits; the single stage amplifier Q3 prevents this loading, and provides a low impedance source for driving other circuits.

The Speed Beep Sound Generator

U11A is wired as a triggered oscillator (one shot); U11B is wired as a VCO and amplifier, with volume controlled by R39. The processor sends a signal when a speed dot is erased. This pulse triggers U11A, which enables U11B for the one shot period.

The Crash Sound Generator

The crash sound is triggered by a negative-going TTL pulse from the logic boad. Transistor Q6 receives no base current until the incoming signal 5 CRASH forward biases diode CR7, creating a base current path charging capacitor C15. When the input signal is removed, diode CR7 is once more reverse biased, leaving the charged C15 to keep the circuit on for a period determined by the RC combination C15, R24,

This circuit, however, does not oscillate. It merely amplifies the white noise previously generated, and thus is like an amplifying switch with a small turn-off delay. C11, C19 and R11 form a damped-wave decay network. A diode in the collector of Q6 provides output isolation.

The Skid Sound Generator

The skid sound is enabled by a TTL low level input from the logic board. This generator consists of a voltage controlled oscillator (used as a tone generator) and an amplitude modulator used to shape the sound volume.

Page 14

When there is no input signal, transistor Q11 is saturated, thus holding U4 pin 5 (the input to the vco) relatively low and U5 pin 2 (the control input to the amplitude modulator) relatively high. This voltage at U5 pin 2 holds the output OFF.

Note that one end of a 68K resistor is tied to the base of Q11 and the other end is tied to the output of U3, an open-collector gate. Given a TTL low level on the input of this gate, the output drives toward ground, thus making the 68K resistor effectively the bottom part of a resistor divider on the base of Qi1.

This would immediately rob Q11 of most of its base current and cause the collector voltage to rise, if not for the 6.8 uF capacitor in the upper half of the divider. This capacitor takes time to discharge, and thus the collector voltage rises gradually. This changes the vco frequency gradualy from low to high.

Since the emitter voltage is the amplitude control input to U5, this also enables the output of the modulator U5 in the same manner (except that a descending voltage increases the output amplitude).

The duration of the input signal 5 SKID determines the duration of the skid sound directly. The output is fed directly to the audio input bus.

The Motor Sound Generator

The Q4 - U10 curcuit generates the motor sound in much the same way that the Q11 - U4 circuit generates the skid sound. The low motor/high motor input is Selected by the position of the control panel FAST button. R52 and R53 control the motor sound frequencies, not the volume. R16 is the volume control. The complements of both the low and high fundamental frequencies are present at the collector of Q12. The input U10-5 has the composite of all fundamentals and harmonics.

The Music Input

The music is generated entirely by the microprocessor on the logic board, out of software. The input on the audio board simply consists of an isolation and volume control network, prior to passing the signal to the audio drivers (U7 and U8).

The Yoke Polarity Driver

This circuit is used only in cocktail table models of CRASH, where the video display must be turned over in order for a player on either side of the table to see an upright picture when it is his turn to play. The circuit is a single D type flip-flop driving a transistor (MJE 182). When this transistor is turned on the collector drives toward ground, thus supplying the yoke relay with the ground it needs to energize and reverse the yoke leads in the video monitor.

The flip-flop U2 is set by a negative-going TTL pulse from the logic board to U2 pin 2; this inverts the picture. U2 is reset by a negative-going pulse from the logic board to pin 13.

Page 15

C. Diagrams, Pinout Table and Schematics

creen |} ——\]_ screen & Stack RAML b p ac UL

Control ROM

our-wa. Control” ee

Playfield Maze & Drone Car Images

Figure 8: Logic Board Block Diagram

Page 16

+15 VDC High Current VCC Sourcefrom Q1 (Used only

+15 vbc

for audio

Regulated power am-

Power Supplyj+15 vpC Low Current plifier

vec Source LM 380s)

From\ 35 VAC Center-Tapped XFMR{ (CT ties to VCC GND)

White Noise

Generator Ul - Q2 Motor Sound Generator u10

Figure 9 Tone Q6 Ampli- Generator fier

Voltage Controlled Oscillator u11 Amplitude Modulator U11

(Snable)= SPEED BEEP Crash 5 CRASH Sound ree . : Enable >| Generator Audio

Skid Sound Generator U2 - U4 Music MUSIC Volume Control R63

Audio Board Block Diagram U8

Inversion Latch & Driver Q8 To video yoke relay

Page 17

Pinout Table

FromToSignalFromToSignal

J1-1 1 player start

J1-2Four-way down5 V common ground
J1-3Four-way left35 Vv CT

J1-4 Four-way up 35 V lead out J1-5 right

J1-6 Ac interlock out J1-7 start AC common J1-8 AC ground J1-9

35 Vv transformer

J2-AAC loused only110 VAC in

for 110 VAC J2-B AC hi \lamp versions

J3-1 Video out 6.3 VAC out J3-2 Ground

33-7 AC gnd 110 VAC hot

J4-1 vcc 5 vbCc

J4-2Ground110 VAC to 5 Vv

power supply J4-3 Coin norm. open AC common

J5-13Static antenna*TRMAC to 5 V power

2 & 4 |supply 55-14 35 VAC CT grounded 310-3 chassis|AC ground ground

35-15 P16-1 |6.3 VAC supply

J5-16 P16-2 [6.3 VAC common

J5-20 Speaker out F1-B AC hot (fused to 35-21 interlock switch)

  • The static antenna is a six inch end is free. Cut 1/4" pieces off long wire in the harness. One end as needed, until static discharges is connected to J5-13; the other no longer turn on the game.
Page 18

Coin Door Monitor BCL 4

Control Panel

v1

Four on Lamp 22] gy P16

Figure 10: Harness Diagram

Page 19

STES6

TPUP <ilers7 -Zlaro7 ‘ore

(See PAGE AIC 10 SMTEA y [see ace PASE)

NOTES

PSALL7400 SERIES TM ARELOW POWER SCHOTTKY

EXIDY ING.

CKASH LOGIC DIAGRAM

PAGE | OF7

MASTER TIMING

CR 50- 31G2-A

Page 20

(See PAGE 4X. MOEL MOEO. 1 MOVID

6341 raice|

634) e341

NOTES ALL7400 SERIES TL'ARE LOW POWER SCHOTTKY swRITER soak

[ EXIDY INC. CRASH LOGIC DIAGRAM | PAGE 20F7

VIDEO GENERATION

CRS0-31G2-A

Page 21

fp 8. im =z)

ae a

NoTES 1 AU. 7400 SERIES ToL ARE LOW POWER SCHOTTKY

EXIDY INC,

CRASH LOGIC DIAGRAM

PAGE 30F?

MAN GENERATION

CRAQ-31G2-A

Page 22

(Cz -OWN pROF SMiNeT. | Ye 73173

He gs wo PF

a ef

Nor ‘USED: ae z a CED 22PINE ose | 3 [leurt BONNER

a

SS Taare 74173

ce Wee

Cc He WEAR

Ce START WO PLAYER, ace

CED SARTONE PLAYER be ree aK ‘come VIDEO

3 A ASE . 7402) hs ras)

Tuso_2} il VIDEO GRouND

  • \ sevens EVERY 2 PACKAGES

NOTES

(ALL 7400 SERIES TTL ARL LOW POWER SCHOTTKY

2, ALL AESISTORS ARE /4W ANDIN OWMS 13 ALCCAPACITORS ARE IN MCG FARADS EXIDY INC. CRASH LOGIC DIAGRAM PAGE. 4 OF 7 INPUT / OUTPUT CR30° 31G2-A

Page 23

v -cFIS-OF 9? LINN ONISSSIONd WHLN3D £406 390d | WvYdVIG 31907 HS Wy? “ONI AGIX3

Svuys OUDIW NI BUY EUOLIDVEYD THY *E SWHONI ON MDA SEY SbO15:S3UTIV 2 LOvL 143943 AWLLONDS HBMOG MOT ZW ULS3IUIS 00% TH

S3LON & a av ae. ae)

a

Page 24

2409 39Vd | WvHOVIC 31907 HSWYo a ay i oy pe 6 v v9 foe es oe Ss ES eS # ze Fico ol eo z [| woo aA e _et a

Fans OY ay tt !

Page 25

+5 VOLTS R39 R38, 15t 15K I ——— 511254 sh. 22K

TEOLE igmsii2| x 4 se be iN. (RG

7507

Tvemp EXIDY INC. CRASH _LOGIG DIAGRAM PAGE 7OF 7 [__€R30-3142-A

Page 26

FROM

XFORMER

+ 5 vour: <a g qT" v cr

+15 volts

R IS0K Ri +5vR thea

gene ai MIEIB2

=

& qos & ae ost mati

REFERENCE DESIG,

[FIRST USED

LAST USED

NOT USED LOW MOTOR,

C43 C3r

CR CRIS CRBS, 134 @5,9,10 Rio, 22,27

VRi VRI HIS gus . Wve Reo. 33K

Lam 3 fon oisth nea CRASH 2 cot ’ tee v us ‘al SKID $40 4 OEMS us-13

WHITE w NOISE am be + Zag TO RSI

R23 100K +5 vours re) opie. waode YOKE, POLARITY DRWER,

sKiO_ENA —___-yy_ve wae . HAO ' 220 a8

sv

ue RX lok GEEPER OUT NOTES [AW RESISTORS. ARE IN OWMS AND I/@W UNLESS

  • ALL CAPACITORS, ABE HN OR ESE Sahm se see ce FARAUS AND ISMVOC

[exipy inc. PAGE IOF 2

CRASH SCHEMATICS. AUDIO TRIO - 3-8 —

Page 27

SKID ENA wf o> 1201 +15 VOLTS R45. 18K +15 voLTs wf t_! $10

U2-& >= ee

WHITE NOISE

R54 +5v 60K RSS Us-m >/MB RR | t_J eT 0.02 ass ose | cas Ont Gl + feos NESGEV g

ve cos:

+15 vours

oul } +15 vours cit RI7 a 10K

22k rd 7 +15V

us-4 >HMB 10K RIS

+5 VOLTS a

  • U3- 10 A

CRASH * CRASH

$20 we

EXIDY INC,

CRASH

SCHEMATICS PAGE2OF2 | AUDIO. €R30- 3161-8

Page 28

Exidy CRASH Selectable Options and Audio Adjustments June,

CRASH has three switch selectable options. a seven segment DIP switch located on the main logic board at position 14A (see Figure 2, item 6). This switch is accessible from the front of the game through the coin door. These are controlled by

Following are the options and the switch settings for their selection:

A. Coinage

Player

Player Player

Player Player aN Coin

Coin Coin

Coin Coin

Crashes (Turns)

Crashes

Crashes

Crashes

Crashes

C. TOP THIS SCORE

Credit awarded for topping score

Credit not awarded for topping score switch switch 4 5

ON ON

ON OFF

OFF ON

switch switch

6 7

on ON

on OFF

OFF ON

OFF OFF

switch

OFF

ON 1979

IV. AUDIO ADJUSTMENTS (see -other side)

MOTOR

MUSIC

VOLUME

CRASH

SPEED BEEP

SKID -- 3 pots:

R52=high frequency

R53=low frequency

R16=volume

-- 1 pot:

R63=volume

-- 1 pot:

R66=overall volume

-- 1 pot:

R29=volume

-- 1: pot:

R39=volume

--'2 pots:

R47=frequency

R49=volume

Page 29
  • 1979 EXIDY, 33-6006 Audio Board Adjustments

R52 MOTOR R53 MOTOR R63 MUSIC R66 VOLUME R29 CRASH DIP switch R39 SPEED BEEP R49 SKID R47 SKID 0 R16 MOTOR

Inc.