CATHODE RAY TOMES

Sarge 2 Player Field Conversion Kit from Demolition Derby 4 Player (M051-00E39-A009)

Demolition Derby (Bally Midway, 1984) · Field Conversion Kit · 14 pages · 17 sections · original scan

Page 1

DEMOLITION DERBY —4 PLAYER TO SARGE-2 PLAYER

Field Conversion Kit Instructions

FOR UPRIGHT ISLAND MAINFRAME MODEL

Cslly MIDWAY MFG. CO 10601 W Belmont Avenue Franklin Park. Ulinois 60131 USA Phone (312) 451-9200 Cable Address MIDCO Telex No.: 72-1596

M05 1—00E39-A009

Page 2
WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

* om

WARNING: This equipment generates, uses and can radiate radio frequency energy andi not installed and used in accordance with the instruction manual, may cause interference to radio communications. |t has been tested and found to comply with the limits fora pass A computing device pursuant to SUBPART J of PART 15 of FCC RULES, which are designed to provide reasdnable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the userat his own expense will be required to take’ whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC “SHOCK DO NOT USE THIS (POLARIZED)

PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

C6ially MIDWAY

OUR TOLL FREE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Video or Pinball - Continental U.S. 800-323-7182

CSally|MIDWAY 19601 West Belmont Avenue Franklin Park, Illinois, 60131 phone (312) 451-9200

©COPYRIGHT MCMLXXXVI BY BALLY MIDWAY MFG. CO. ALL RIGHTS RESERVED.

NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF & PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: BALLY MIDWAY MFG. CO., 10601 W. BELMONT AVE., FRANKLIN PARK, IL 60131.

Printed in U.S.A.

Page 3
WARNING

The parts contained in this field conversion kit must be installed without deviation from the instructions contained in this manual and kit. Failure to fotlow these instructions in every detail may result in the creatian of illegal interference to radio and TV reception.

RALLY MIDWAY has verified that this field conversion kit, when Installed in the game(s) specified in this manual, complies with the requirements in Part 15 of the FCC rules for a Class A computing device. Operation of this equipment in a residential area may. cause unacceptable interference to radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference,

RALLY MIDWAY will not be responsible for incomplete or improper conversions, or installation in a game for which this field conversion kit is not intended. If this field conversion kit is installed in a game that is not specified in this manuat or in a previously converted game, the operator is required to take whatever steps are necessary to insure compliance with the requirements in Part 15, Subpart J, of the FCC Rules for a Class A computing device.

SPECIAL NOTE:

THE PARTS REMOVED, WHILE MAKING MODIFICATIONS EXPLAINED IN THIS MANUAL, WILL NOT RE REUSED IN FUTURE GAME CONVERSION KITS.

The word "discard", as used in this manual, makes reference to this fact. . All parts removed may be considered usable for other purposes.

Page 4

REMOVE LATCH CLAMP& SHELF SUPPORT

RED CAR BLUE CAR _

SKETCH #1

SERVICE DOOR

FIRST SCREW

NEW END CAP(RIGHT & LEFT)

v—— FIFTH SCREW ( 3/4" )

REINSTALLED LATCH CLAMP AND NEW SHELF SUPPORT

-— 2 WASHERS UNDER FOURTH SCREW

SKETCH #2

D THIRD SCREW

Page 5

TO CONVERT "DEMOLITION DERBY" 4 PLAYER UNIT INTO A 2 PLAYER "SARGE", FOLLOW THE STEPS AS OUTLINED BELOW:

GREEN/YELLOW CAR CONTROL PANEL REMOVAL & REPLACEMENT

NOTE: The two player SARGE will use the Blue Car/Red Car end for mounting the new control shelf. A blank cover will replace the control panel on the Green Car/Yellow Car end of the cabinet.

Step 1: Removing Green/Yellow Car Control Panel As) Unlatch the Green Car/Yellow Car control panel and open, Disconnect all cable clamps and cable connector blocks leading to the «control panel. Y Remove all control panel hinge screws and remove control panel.

Step.2: Removing Green/Yellow Car Coin Acceptors

Ae) to remove coin acceptors, begin by removing cable clamps, connector

~~~ blocks and bayonet connectors at the speaker. “By Cut both wires to the slam switch at the lock,

C.)- Remove the trip switch from the acceptor on the YELLOW side. This will f De) Remove carriage bolts, nuts and washers. Save for Step 3

a ase removal of both acceptors and cable without soldering. f De) Remove carriage bolts, nuts and washers. Save for Step 3. Sten 3:/ Installing Coin Acceptor Cover Plate ‘hey Using kit furnished cover plate, attach by using bolts, nuts and washers taken from coin acceptor plate. NO WASHERS are required at the top two bolts. fn fC.

Step 4; /Installing Control Shelf Cover Plate

4 A.) Y6 install blank cover, put in place kit furnished cover, and latch

lock. This completes the new non-playable end of the unit.

BLUE/RED CAR CONTROL PANEL REMOVAL & REPLACEMENT eo

Removing Blue/Red Car Control Panel A.)Anlatch, open and disconnect all cable clamps and connectors leading to the control shelf. Remove hinge retaining screws and remove shelf. use. JRemove four screws from each of the shelf support brackets.

ey ching clamps. (See Sketch #1)

NOTE: Do’ NOT remove plastic locating pins in the cabinet sides. Saye screws for further

Save

Step 2! Mounting New "Sarge" Control Panel A. To mount new end caps, position part onto the plastic pins left in place. New end caps have additional pins that repositions the new shelf pport and is pre-drilled for easy attachment. "C" clamp the end cap and support bracket to the cabinet side and attach ith the first 14" screw. (See Sketch #2) emount the shelf latch with 2nd and @rd ag" screws. ‘The fourth pre-drilled hole requires two washers under the fourth 13" screw. \

Page 6

e last remaining hole in the shelf support uses a short 3/4" screw <removed from the hinge on the opposite end. (see Step 1, Item C under ~~ Joreen Car/Yellow Car) A lepeat the above procedure for the other side. YC.)/fo attach SARGE control shelf, place offset hinge (similar to Demolition

  • Derby) and fasten with previously removed screws.

REMOVAL AND MODIFICATION OF PRINTED CIRCUIT BOARDS

The MCRIII Logic P.C. Board Assembly ‘and the Turbo Cheap Squeak Sound P.C. Board will both require the re-installation of new E-PROMs. The kit includes the E-PROMs necessary to complete the modification. Please read through the following instructions carefully to prevent any damage to the components involved.

Step 1: Removing The MCRIII Logic P.C. Board Assembly A.) Open the service door and locate the MCRIII Logic P.C. Board Assembly mounted to the right inside wall of the cabinet. B.) Disconnect all cables from the end of the p.c. board assembly closest to the service door you have just removed. C.) Loosen the top two holA=down screws and lift up on the p.c, board until the whole assembly can be pulled away from the inside wall of the cabinet. D.) Carefully pull the p.c. board” assembly out of the cabinet until the power supply cable, connected to the assembly, is exposed. E.) Disconnect this cable and finish removing the p.c. board assembly.

Step 2: Removing The Turbo Cheap Squeak Sound P.C. Board A.) Locate the Turbo Cheap Squeak-Sound P.C.B. mounted on the inside wall of the cabinet. B.) Loosen and remove all mounting screws and carefully remove p.c. board from cabinet.

NOTE: Now that you have the MCRIII Logic P.C. Board Assembly and the Turbo Cheap Squeak Sound P.C.B. removed from the cabinet, place them both on a flat clean work surface for further disassembly.

Step 3: Disassembling The MCRIII Logic P.C. Board Assembly A.) Place the MCRIII Logic P.C. Board Assembly face down, exposing the metal. shielding plate on its backside.

B.) Loosen and remove all screws securing the first metal plate to the

assembly. C.) Lift the metal plate off the p.c. board assembly and place on the side. D.) Once this metal plate has been removed, the backside of a printed circuit board will be exposed. ) Lift an fold this p.c. board over to the side, laying it face-up (E-PROM side up) and exposing the second metal plate in the p.c. board assembly. ) Loosen and remove all screws securing the second metal plate to the assembly. ) Lift this metal plate off the p.c. board assembly and place on the side. -) Once you have removed the second metal plate, another p.c. board will be exposed.

Page 7

Step 4: Installing The New "Sarge" Program Code A.) With the two sections of the MCRIII P.C. Board Assembly lying face-up, (E-PROM side up), locate the E-PROMs. To replace these E-PROMs with the new E-PROMs supplied in the kit, refer to the parts list on page 10 and label information on each E-PROM.

NOTE: The next steps of this procedure must be conducted with extreme care to avoid damaging the program stored in the E-PROMs you are about to replace. We suggest every precaution listed to avoid problems. If they are exposed to it, the smallest amount of static electricity can permantly damage the program stored in the E-PROMs. B.) Ground yourself BEFORE handling each E~PROM. This can be accomplished in many ways. For example, if you are working next to a game cabinet and if it is still plugged into the wall outlet, just touch the ground strap you removed from the p.c. board assembly. You could also touch the metal center screw which holds the plug plate in place over the wall outlet or you could touch the grounding strap of your work bench, if that is where you will be conducting the modifications. C.) Gently work a small screwdriver under the E-PROM you want to remove. At the same time, grasp it with your other hand and lift gently. Guide it out of the socket in this manner to help avoid damaging the E-PROM's pins and the pins of its socket. .) Set the removed E~PROM aside. +) Ground yourself again. +) Pick up the replacement E-PROM and install it into the socket you just emptied. Avoid, as much as possible, touching the E-PROM's pins. Aho
WARNING: The notch at one end of the E-PROM MUST be matched with the end of.its intended socket, which contains a similar notch. If you put the E-PROM in its socket backward and turn on the power to the game, you will destroy it.

Step 5: Reassembling & Installing Modified Printed Circuit Boards A.) Reverse the steps described on the preceding pages to reassemble the modified unit.

Page 8
  • “SARGE" DECAL PLACEMENT

SPEAKER GRILLE

SKETCH #3 a

Vv

Page 9

DECAL_INSTALLATION_INSTRUCT IONS

READ THE FOLLOWING INSTRUCTIONS THROUGH COMPLETELY AT LEAST ONCE BEFORE ATTEMPTING TO

INSTALL THF DECAL(S) THEY CONCERN! !

THE DECAL(S) ARE COMPOSED OF THREE (3) PARTS: 1)A HEAVY WAXED BACKING SHEET WHICH COVERS THE STICKY SIDE OF THE NECAL, 2) THE DECAL !TSELF, AND 3)A THIN MASKING SHEET WHICH 1S ON THE FRONT SIDE OF THE DECAL TO PROTECT |T AND TO AID JN ITS INSTALLATION.

eee ROR HR HH HHH TO INSTALL THE DECAL(S), PROCEED AS FOLLOWS: * * * * ® ¥ # HH ® *

  • RE SURE THE AREA WHERE YOU ARE GOING TO APPLY THE DECAL 4S CLEAN ANN FREE OF ALL DIRT, GREASE, AND GRIME.
  • USING ANY SPRAY-ON GLASS CLEANER, THOROUGHLY WET DOWN THE AREA WHERE YOU INTEND TO PUT THE NECAL.
  • REMOVE. THE HEAVY WAXED RACKING SHEET FROM THF DECAL RY POSITIONING IT FACF UP ON A FLAT SURFACE; GOING TO ANY CORNER; AND RENDING THIS CORNER UP SLIGHTLY TO SEPARATE THE DECAL AND THIN MASKING SHEET FROM THE HEAVY WAXED RACKING SHEET.
  • SLOWLY AND CAREFULLY PEFL THE HEAVY WAXFN RACKING SHEET AWAY FROM THF DECAL AND MASKING SHEFT.
  • PLAGE THE MECAL ON THF GAME CABINET QVER THE WET GLASS CLEANER YOU JUST APPLIED. (THIS WILL ALLOW A SMALL AMOUNT OF FINAL POSITIONING TO RE DONE AFTER THE DECAL 1S APPLIED TO THE GAME CABINET.)
  • SMOOTH THE DECAL.
  • ALLOW THE DECAL TO RECOME FIRMLY AFFIXED TO THRE GAME BEFORE PROCEEDING TO THE NEXT STEP.
  • REMOVE THE THIN MASKING SHEET FROM THE DECAL AT THIS TIMF RY MOISTENING IT WITH A WET CLOTH OR SPONGE. RUB WITH FINGER TIPS (NOT NAILS) FROM A CORNER EDGE TOWARD JTS CEN- TER. PERL THE THIN MASKING SHEET RACK OVER ITSELF TO REMOVE IT. DO NOT PULL IT STRAIGHT AWAY FROM THE CARINET.

-T-

Page 10

SARGE ;

OPTION SWITCH SETTINGS

VIVITITITITILTLTIT LITT SWATCH NOw 2 = AT A 13 - LOCATED ON MONOROARD///S///S/SS//SI/TTISIILL

DURING GAME PLAY: 2SW#1 SWH2 SWE3S SWRA SWE5 SW#6 SWH7 SW#B SWEO SWHIO NOT NOT. NOT NOT NOT NOT USED USED USED USED USED USED

  • NO FREE PLAY OFF FREE PLAY ON

we 1 COIN / 1 CREDIT OFF OFF 2 COINS/ 1 CREDIT ON OFF 1 COIN / 2 CREDITS OFF ON

NORMAL OPERATION FREEZE VIDEO

PART NO. M051-00B88-B007

THE REMAINDER OF YOUR NEW GAME'S MOST COMMON OPTION SETTINGS ARE CONDUCTED DURING YOUR GAME'S SELF-TEST MONE

Page 11

LIST OF MAJOR PARTS INCLUDED IN YOUR FIELD CONVERSION KIT FOR CONVERTING DEMOLITION DERBY U.R. 4-PLAYER TO SARGE U.R. 2-PLAYER

PART NO. DESCRIPTION

AE39-00004-0000 CONTROL SHELF ASSY. (INCLUDES ITEMS 1A THRU 1P)

AA57-00027-0100 TRIGGER SWITCH ASSY.=RIGHT (2 REO'D.)

AA57-00028-0000 BUTTON SWITCH ASSY.-RIGHT

AA57~00029-0000 SWITCH-ASSY: TRIGGER

0A57-00104-0100 BRKT.=SWITCH RIGHT

0020-00243-0000 PLATE: SPRING (2 REQ'D.) ELLE TRIGGER SWITCH ASSY.-LEFT (2 REO'D.) 1B AA57-00022-0200

1RA | AA57~00028-0100 BUTTON SWITCH ASSY.-LEFT

AA57-00029-0000

0A57-00104=0200 SWITCH-ASSY: TRIGGER

BRKT.-SWITCH RIGHT

0020-00243-0000 PLATE: SPRING (2 REO'D.)

AB88~-00012-0000 CONTROL~ASSY. (4 REO'D.)

AA57-00012-0000 CONTROL BRKT. & REARING ASSY,

AA57-00013-0000 |RRKT., BUSHING & BEARING ASSY.

AA57-00032-0000 CONTROL GRIP CABLE ASSY.

A941~-00022-0100 ROLLER SWITCH ASSY.-LEFT

A941-00022-0200 ROLLER SWITCH ASSY.-RIGHT

0A57-00703-00XF PIN: SPRING

0A57-00902-00XF TUBING: GRIP EU 0010-00602-0000 SPRING: EXTENSION

0941-00108-0090 BRKT.: SWITCH

-9~

Page 12

CONVERTING DEMOLITION DERRY U.R. 4—-PLAYER TO SARGE U.R. 2~PLAYER LIST OF MAJOR PARTS (CONT'D.) §NCLUDED IN YOUR FIELD CONVERSION KIT FOR

ITEM PART NO. DESCRIPTION

i 10d 0941-00109~0000 ;ACTUATOR: SWITCH

1CK | 0941-00702-00XF PIVOT - PIN

1CL_ | 0941-00704-00XF SPACER

1CM | 0941-00905-0000 | BUMPER: RURRER =

1D AE39-00005-0000 |CONTROL SHELF CABLE ASSY.

1E AE39-00006-O0XF |CONTROL SHELF-WELD ASSY.

1F 0A57-00904-0000 |SLINE (4 REO'D.)

0A57-00908-00XF PUSH BUTTON: RED (4 REO'D.)

0A57-009 10-0100 GRIP: RIGHT (2 REQ'ND.)

0A57-009 10-0200 GRIP: LEFT (2 REO'D.)

0£39-00900-0000 OVERLAY: CONTROL SHELF

0017-00032-0093 fe SWITCH: W/HOLDER, WHITE (2 REQ'D.)

0017-00042~0256 PUSH BUTTON - ROUND: RED 1H

VW

VJ

1K

1M 0017-00042-0262 PUSH BUTTON - ROUND: RLUE

IN 0307-00908-0000 {TRIGGER MOLDED (4 REO'D.)

10 0307-00925-0100 |GRIP: OUTSINE - RT. SIDE / RT. HAND (2 REO'D.)

+ 7 1P 0307-00925-0200 |GRIP: OUTSIDE- LT. SIDE / LT. HAND (2 REO'D.)

2 AE39~00007-O0XF |CONTROL COVER ASSY. (BLANK)

3 AE39-00008-0100 {END CAP & PIN ASSY.-RIGHT L | — 4 AE39-G0008-0200 ;END CAP & PIN ASSY.-LEFT

INSTRUCTION SHEET & BAG ASSY.

=10-

Page 13

LIST OF MAJOR PARTS (CONT'D.) INCLUDED IN YOUR FIELD CONVERSION KIT FOR CONVERTING DEMOLITION DERBY U.R. 4—PLAYER TO SARGE U.R. 2-PLAYER

1TEM

5A FORM~00041-8005 |POST CARD: CUSTOMER REPLY

5R MO51-OOE39~A007 |TAG: OPTION SWITCH SETTINGS PART NOw DESCRIPTION

Mi 105 1=0NE39-A009 oe INSTRUCTION MANUAL

E39A~22AAE~AXRD |EPROM: 2764 (POSITION "5F" ON 5 MHZ. C.P.U. RO.) oo E39A-22AAE-RXRD | EPROM: 2764 (POSITION "6F" ON 5 MHZ. C.P.U. BD.)

27128 (POSITION —$<—<$—$ $$. "IC" ON 5 MHZ. C.P.U. AD.) 8 E39A=-42AAE-JX4D | EPROM:

E39A-42AAE-KX4D EPROM: 27128 (POSITION "2C" ON 5 MHZ. C.P.U. BD.) r 10 E39A-42AAE~LX40 [EPROM: 27128 (POSITION $$$ +} "3C" ON 5 MHZ. G.P.U. BD.)

ia EB9ASA2AAE-MXAD | EFROM: 27128 (POSITION "4c" ON MHZ. C.P.U. BD.)

i ee _—$—$ $$}

cam E39A-22AKE-CXRD | EPROM: 2764 (POSITION "U4" ON TURRO CHEAP SOK, BD.)

13 E39A-22AAE~DXRD | EPROM: 2764 (POSITION "U5" ON TURBO CHEAP SOK. BD.)

T 1

14 E39A-42AAE-AX4D |EPROM: 27128 (POSITION "1A" ON SUPER VIDEO GEN. AN.) : | E39A-42AAE=BX4D |EPROM: 27128 (POSITION "Zan ON SUPER VIDEO GEN. BD.)

16 E39A-42AAE-CX4D |EPROM: 27128 (POSITION "3A" ON SUPER VIDEO GEN. BD.)

17 E39A-42AAE-DX4D |EPROM: 27128 (POSITION "4A" ON SUPER VIDEO GEN. BD.) ESOA-A2AAE-EXAD[FPROM: 27128 (POSITION "5A" ON SUPER VIDEO GEN. BN.) | 19 E39A-42AAE-FX4D |EPROM: 27128 (POSITION "6A" ON SUPER VIDEO GEN. BD.) _

1 tb 20 E39A-42AAE-GX4D |EPROM: 27128 (POSITION "7A" ON SUPER VIDEO GEN. BD.) 21 [eet tn 27128 (POSITION "BA" ON SUPER VIDEO GEN. AD.) *, |

22 0E39-00901-0000 DECAL (2 REQ'D.) } 23 0017-00009-0629 PAINT: SATIN BLACK 1/2 PINT CAN

Page 14

¥ CAPORUSSO BALLY MIDWAY MFS&.

SARGE CONVERSION FROM DEMOLITION DERBY 4 PLYR MO51-0@B68-AGe3 co.

PLYR 1 LEFT DOWN

PLYR 1 LEFT UP

PLYR 2 LEFT UP

PLYR @ LEFT DOWN

PLYR @ LEFT TRIGGER

PLYR 2 RHT TRIGGER

PLYR @ LEFT THUMB SW PLYR 2 RHT THUMB SW PLYR 2 RHT DOWN PLYR 2 RHT UP PLYR 1 RHT UP PLYR 1 RHT DOWN PLYR 1 LEFT TRIGGER PLYR 1 RHT TRIGGER PLYR 1 LEFT THUMB Si PLYR 1 RHT THUME SH BLUE ARMY START SW RED ARMY START SW. SH_RETURN L_., ou 6 POS CAP/MALE PINS 4 POS CAP/MALE PINS 15 POS CAP/MALE PINS TO_EXISTING CONTROL CABLE CONNECTORS ON THE MASTER CABLE