CATHODE RAY TOMES

Joust Instruction Manual (16P-3006-101) Oct 1982

Joust (Green label) (Williams, 1982) · Instruction Manual · 12 pages · 14 sections · original scan

Page 1

16P-3006-101

INSTRUCTION MANUAL

FOR

UPRIGHT GAMES

including procedures for...

  • operation ° auditing ¢ adjustment ¢ diagnostics

FOR SERVICE... Du, .

NOTE NEW TOLL-FREE TELEPHONE NUMBERS: ELECTRONICS, INC. 3401 N. California Ave. 800-621-1253 Chicago, IL 60618 Cable Address: WILCOIN, CHICAGO IN ILLINOIS CALL: (312) 267-2240 800-572-1324
Page 2

ROM SUMMARY

ROM

JOUST 1A

JOUST 2A

JOUST 3A

JOUST 4A

JOUST SA

JOUST 6A

JOUST 7A

JOUST 8A

JOUST 9A

JOUST 10A

JOUST 1A

JOUST 12A

Decoder ROM 4 (Horizontal)

Decoder ROM 6 (Vertical)

Video Sound ROM 4

Special Chip 1

POWER TURN-ON

CAUTION - This game must be plugged into a properly-grounded outlet to prevent shock hazard and to ensure proper game operation. DO NOT use a “cheater” plug to defeat the ground pin on the line cord, and DO NOT cut off the ground pin.

WHEN THE GAME JS FIRST TURNED ON it produces a sound. Simultaneously general illumination should come on and a moment later a scanning “rug pattern” indicating the RAM test should appear on the screen. Next the rug should become stationary as the ROM test is performed. In a correctly-running game the rug pattern will be followed by the message “INITIAL CHECKS INDICATE ALL SYSTEMS GO”. If RAM or ROM failure messages. PART NO.

A-5343-09961-A.

A-5343-09962-A

A-5343-09963-A

A-5343-09964-A

A-5343-09965-A

A-5343-09966-A.

A-5343-09967-A

A-5343-09968-A A-5343 .09969-A A-5343-09970-A-

A-5343-09971-A

A-5343-09972-A

A-5342-09694

A-5342-09821

A-5343-09973

A-5410-09911 DESCRIPTION

PROM, 4Kx8, YELLOW LABEL

“PROM, 4Kx8, YELLOW LABEL

PROM, 512x8

PROM, 512x8

ROM, 4Kx8

Special Chip

come up on the screen instead, refer to Power-Up Tests in TROUBLESHOOTING PROCEDURES.

GAME OPERATION

GAME START - Insert coins; a random sound is produced and credits are displayed on the CRT. With two or more credits displayed, pressing 2-player start initiates a 2-player game where each player gets five* mounts (turns).

*adjustable feature

Page 3

PLAYER CONTROLS

THE JOYSTICK sends the gladiator and his ever-stalwart mount (ostrich or stork) boldly to the left or to the right.

THE FLAP BUTTON causes the hero’s mount to spread its robust wings.

GAME PLAY

AT SOME FAR-DISTANT TIME two fantastic gladiators meet and square off for battle. Each is mounted on a fanciful bird of prey (ostrich or stork) whose wings can carry it from the clifftops to the mouth of the abyss and hopefully back. . .or the bubbling lava below will increase its toll.

While your mount is a skilled flyer, your opponent is a shrewd gladiator. You must prove you are his better. Stealthily you must pilot your mount above him, and cleverly you must stalk him. . . to strike at the moment in which he least suspects you! And always remember this rule: In every joust, the highest lance wins.

Of course your opponent will resist your attempts, all the while pursuing his own designs against you. Each gladiator has five* mounts. Every time you’re toppled, you must mount a new bird for the next joust. The gladiator who scores the most dismountings is the winner.

YOUR PATH MAY SEEM CLEAR and your work cut out, but just then a flock of vicious Buzzard-Riders will ambush you! Ruthless even as they are dismounted, these wily Buzzard-R ders instantly lay their eggs. You must pick up the eggs or they will soon hatch into even more persistent and antagonistic foes!

Fortunately at 20,000* points (should you make the grade) you will be awarded another bird to mount against the loyal opposition.

Joust is designed for either one or two players.

HIGH SCORE SIGNATURE

Select letters with the joystick. Push right to move forward through the alphabet; push left to move backward. Then push the FLAP button to lock in the letter,

BOOKKEEPING AND EVALUATION TOTALS

  • In Game-Over Mode, open the cashbox and depress the cashbox advance switch. The advance switch located on the coin door can also be used. (See Figure |.) The CRT should indicate all bookkeeping and evaluation totals. If so, go-to step 3. If the CRT display comes up in the ROM test, perform step 2.

AUTO-UP- O@O HIGH MANUAL- ADVANCE. SCORE DOWN

Figure 1. Coin Door Button Switches

  • Continue to depress the cashbox advance switch, stepping the game through test programs for ROMs, RAMs, CMOS RAM, sounds, switches, color RAMs, and then CRT test patterns, of which there are five. The fifth test pattern, color bars, directly precedes the CRT display of the bookkeeping and evaluation totals.
  • The bookkeeping and evaluation totals appear on the displays as in Figure 2.
  • adjustable feature
Page 4

CLEARING BOOKKEEPING TOTALS

  • Depress ADVANCE to display Game Adjustments.
  • Operate PLAYER 1 joystick to position cursor on CLEAR BOOKKEEPING TOTALS.
  • Push PLAYER 2 joystick.
  • Depress ADVANCE.

BOOKKEEPING TOTALS

LEFT SLOT COINS CENTER SLOT COINS RIGHT SLOT COINS PAID CREDITS FREE MEN TOTAL TIME [N MINUTES TOTAL MEN PLAYED TOTAL SINGLE PLAYER TOTAL DUAL PLAYER TOTAL CREDITS PLAYED AVERAGE TIME PER CREDIT

Figure 2. Bookkeeping Display

GAME ADJUSTMENTS

In the Game-Over Mode open the coin door. With the AUTO-UP/MANUAL-DOWN switch set to AUTO-UP, depress the coin door ADVANCE switch twice to cause a CRT display as shown in Figure 3.

Select the function you wish to change by moving the PLAYER 1 joystick (push right to move arrow down, left to move arrow up). Then, making sure the coin door is open, push the PLAYER 2 joystick right to increase or left to reduce the value of the selected function.

The number of turns (men) per I-credit game can be set anywhere from I to 99 (5 recommended). Difficulty is factory-programmed at 5 (moderate). It can be custom programmed (0-9, with 9 conservative) as desired.

Game Pricing is selected with standard settings or with custom settings as shown in Tables | & 2. Table | lists some common pricing schemes and directs the reader to the proper entry in Table 2, which shows what the CRT display should look like to accomplish the desired pricing. Note that free play can be elected by entering the code number 9 at the PRICING SELECTION function (see Tables 1 and 2).

For standard settings you need change only the PRICING SELECTION. For custom settings, first set PRICING SELECTION to zero and then set the remaining values according to Table 2.

Page 5

GAME ADJUSTMENTS

EXTRA MAN EVERY 20000 MEN FOR 1 CREDIT GAME 5 HIGH SCORE TO DATE ALLOWED YES PRICING SELECTION 3B 1/QUARTER 4/D00LLAR LEFT SLOT UNITS CENTER SLOT UNITS RIGHT SLOT UNITS UNITS REQUIRED FOR CREDIT UNITS REQUIRED FOR BONUS CREDIT MINIMUM UNITS FOR ANY CREDIT DIFFICULTY OF PLAY LETTERS FOR HIGHEST SCORE RESTORE FACTORY SETTINGS CLEAR BOOKKEEPING TOTALS HIGH SCORE TABLE RESET AUTO CYCLE SET ATTRACT MODE MESSAGE SET HIGHEST SCORE NAME

USE ‘PLAYER | MOVE’ TO SELECT ADJUSTMENT USE ‘PLAYER 2 MOVE’ TO CHANGE THE VALUE PRESS ADVANCE TO EXIT

Figure 3. Game Adjustments Highest Score Signature The number of letters allowed the highest-scoring player for entering his name can be varied from 3 to 20 and is recommended as 3. If objectionable words are entered as the signature name, you can change the lettered entry leaving the highest score the same. See Setting Highest Score Name.

Restore Factory Settings

  • Position the cursor on RESTORE FACTORY SETTINGS.
  • Push PLAYER 2 joystick to right.
  • Depress ADVANCE switch twice. Resetting High Score Table
  • Position the cursor on RESET HIGH SCORE TABLE.
  • Push PLAYER 2 joystick to right.
  • Depress ADVANCE.

vaute Attract Mode Message

Position the cursor on SET ATTRACT MODE MESSAGE. Push PLAYER 2 joystick to right. Depress ADVANCE. Enter up to two lines of your message following instructions on the screen. Depress ADVANCE to terminate process. Laks meg

NOTE: To restore the Williams attract mode message, perform steps 1 through 3 and then turn the game OFF and back ON.

Setting Highest Score Name I. Position the cursor on SET HIGHEST SCORE NAME.

  • Push PLAYER 2 joystick to right.
  • Depress ADVANCE.
  • Enter new signature; depress ADVANCE to terminate process.
NOTE: An alternate, simpler method enters the factory highest score signature. In the Game Over mode, hold HIGH SCORE RESET depressed. After a few seconds a sound is produced and the factory highest score signature has been activated.
Page 6

Table 1. Pricing Schemes

TABLE 2 COIN DOOR STANDARD SELECTION/ MECHANISM. CREDITS/MONEY CUSTOM KEY

Twin QuarterW/25¢ S/$1A
Quarter, Dollar, Quarter2/50¢ 5/$1B

1/25¢ 4/S1 3 2/50¢ 4/$1 Cc WVSO0¢ 3/$1, 4/$1.25 D 1/50¢ 3/$1, 7/$2 E VW50¢ 3/$1, 6/$2 I 1/50¢ 5

IDM, SDM1/1 DM, 6/5 DM2
20-Cent, 50-Cent1/20¢ 3/50¢F
I Franc, 5 Franc1/2F, 3/SF only4
25 Cent,1/25¢ 4/1G6
1 Guilder1/25¢ 5GG
5 Franc,VSR, 2/10F7
10 Franc1/10F8
| Franc, 2 Frane2K, 5/2F2
100 Lire, 200 Lire1/200 Lire8
Twin CoinI Coin3

1/2 Coins Ss 1/3 Coins, 2/5 Coins H

1 Unit, 5 Unit1/2, 3/54

WL, 5/5 I 1/3, 2/5 J

FREE PLAY_9

Table 2. Pricing Settings

CUSTOM KEY DISPLAY FUNCTIONS STANDARD SELECTION A/|B)/C|/D/E|F/G/H/ 1] J

Pricing Selection 1}2/3/4}/5/6/7;8/9}0/0;0)0/0)0;0}0!)0]0

Left Slot unitsL)6; rfryryrytpateybydyay 3] ey a} 27042

Center Slot units 410) 4]16)4)/0}0]0/) 4) 4) 4] 4)12/48}0)0)0/0!0

Right Slot unitsP}tliyo} it) 4) 2) 2; nr)ryrn}i]s] i2}is) 4) 2) 5) 10
Units per credit2) EL]2; 2); 07;2) 2; rb)rptyity 4yt4p spry sft) 5s

Units required for bonus credit | 4} 0!0/0/0/0|)0)0)0]4]4/0]15/96)0/4/0/)0;0 Minimum units for any credit | 0 | 0/010) 0/0/0/0]0/0 > 2]2)0)|24/0}0/0)0/0

Page 7

Certain types of game malfunctions may inhibit the game’s diagnostic or display faculties. Troubleshooting procedures for most of these types of malfunctions as well as malfunctions that permit selfdiagnosis are covered below. Our troubleshooting algorithm begins TROUBLESHOOTING PROCEDURES

NO GENERAL ILLUMINATION POWER-UP TESTS

NO INITIAL VIDEO (RUG PATTERN) with Power-Up and continues until Game Over Mode. All procedures can be performed with minimal test equipment or merely by observing the game itself.

CHECKING POWER SUPPLY BOARD

  • Check fuse F2 on power supply board.
  • Check for proper installation of jumpers WI, W2, W3 and/or resistor R27. (Some machines MAY NOT have an R27. Refer to your drawing set.)
  • Check 4PU/JI, 4P3/J3, 6P2/12 and 6P3/ 3B.
  • [fall the above don’t turn up the problem, check power supply board.
  • Open back doors.
  • Press reset button on CPU Board
  • Try RAM and ROM tests (see below).
  • Ifall the above don’t turn up the problem, check power supply board.
  • Swap power supply board with one from known-good game.
  • If game plays, problem is on power supply board.
  • If game doesn’t play, check power transformer with voltmeter.
  • If known-good power supply is unavailable for tests above, check +5V, —SV and + 12V outputs on power supply in game. Each MUST BE within 2% of rated output with less than 0.1% AC hum.

MORE POWER-UP TESTS

ROM BOARD LEDS RECOGNIZE CONDITION GENERAL | “0” means all power-up tests passed ROM BOARD LEDS IDENTIFY BAD CHIPS REMEDY

  • scanning rug pattern
  • stationary rug pattern
  • “INITIAL TESTS INDICATE ALL SYSTEMS GO”
  • Game-Over Mode If any video (see left) is missing or error message is displayed, proceed to Diagnostic Mode tests.

CMOS (See Appendix A) “0” means tests passed

“0” means tests passed BATTERY | “O” means tests (See passed Appendix A) “HIGH SCORE TABLE RESET” “BOOKKEEPING TOTALS CLEARED” “ADJUSTMENT FAILURE” “RESTORE FACTORY SETTINGS

  • Open coin door and turn power off and on.

BY OPENING FRONT DOOR OR TABLETOP AND TURNING GAME ON AND OFF”

“FACTORY SETTINGS RESTORED”

  • Press ADVANCE. Game should return to Game-Over Mode.

“HIGH SCORE TABLE RESET” “BOOKKEEPING TOTALS CLEARED” “ADJUSTMENT FAILURE” “RESTORE FACTORY SETTINGS

  • Open coin door and turn power off and on. Or: press ADVANCE. In either case, game should return to Game-Over Mode. BY OPENING FRONT DOOR OR TABLETOP] (2) Check AA alkaline cells on CPU AND TURNING GAME ON AND OFF” Board,
  • If problem persists, proceed with CMOS RAM test by putting the game into its Diagnostic Mode (see SELF-DIAGNOSTICS).

MEMORY PROTECT INTERLOCK (See ‘Appendix A) “0” means tests passed

SPECIAL CHIP “OQ” means tests passed “HIGH, SCORE TABLE RESET” “BOOKKEEPING TOTALS CLEARED” “ADJUSTMENT FAILURE” “RESTORE FACTORY SETTINGS

  • Making and breaking coin door interlock switch, check with VOM and replace if faulty.
  • Replace if faulty: Memory protect BY OPENING FRONT DOOR OR TABLETOP AND TURNING GAME ON AND OFF”
  • scanning rug pattern
  • blank screen instead of “INITIAL TESTS. INDICATE ALL SYSTEMS GO”
  • high score table with no scores
  • intro blank or program crash gates 6E, IC], Ql, or CMOS RAM IC.
  • Turn power off.
  • To find bad chip, replace 2 special chips one at a time with known good chips.
  • Turn machine on after each replacement and run through Power-Up Tests.
Page 8

+5VDC ADJUSTMENT (R10 & R24) Before adjusting the voltage output, always check at the output of the supply for AC hum. This hum should never rise above .005V on the +5VDC suppiy. If it does, consult your schematic drawing set for proper DC voltages throughout the circuit. Test for these with the DC setting of your multimeter. Make a second check using the AC setting. Pay particular attention to readings at TPS (top of capacitor C10). If the voltage here is low (less than + 11 VDC) or if you find excessive ripple (more than 700mVrms), replace the capacitor.

Table 3. Voltage Adjustments to +5VDC Power Supply

WHICH RESISTORS SUPPLY

HAS...neitherRIO onlyR24 onlyR24 & RIO

TO INCREASE VOLTAGE IF remove RIO

UNDER 4.95VDC...add R24or add R24_remove RIO

TO DECREASE VOLTAGE IF remove R24

OVER 5.25VDC...add Ri0or add RIOremove R24

SELF-DIAGNOSTICS If RAM or ROM failure messages are displayed on the CRT after the “rug pattern,” proceed with self-diagnostics. Self-diagnostic procedures are controlled by the AUTO-UP/MANUAL-DOWN and ADVANCE switches on the coin door. (See Figure |.) Set the AUTO-UP/MANUAL-DOWN switch to the MANUAL-DOWN position and depress the ADVANCE pushbutton. The game is now in its Diagnostic Mode and a ROM test is performed. With ROM test results present on the CRT display, set the AUTO-UP/MANUAL-DOWN switch to the AUTO-UP position. Depressing the ADVANCE pushbutton initiates the RAM test. Further tests (CMOS, sound, switch, color RAM and monitor test patterns) are encountered one after the other as the ADVANCE pushbutton is depressed (once more for each subsequent test). MONITOR TEST PATTERNS - For ease in monitor adjustments, the monitor may be slid back and the screen viewed in the CRT mirror provided on the inside-top of the cabinet. Remove the two bolts and carefully slide the monitor back in its shelf. Secure the monitor in the extended position by inserting the two bolts through holes provided at the left side of the monitor. AUTO CYCLE MODE - From the color bar pattern (or Game Over with the switch set to AUTO-UP) depress ADVANCE two times to display GAME ADJUSTMENTS.

  • Position the cursor on AUTO CYCLE with the PLAYER | joystick and push the PLAYER 2 joystick right. Depress ADVANCE. The system will now sequence through ROM, RAM, and CMOS RAM tests repeatedly. The coin door must be open during the Auto Cycle test. If an error is detected, the test is terminated and the failure indication is displayed on the CRT.
  • To terminate the Auto-Cycle test, turn the game OFF and ON. wn

LEGEND: FIRST DESIGNATION (3K) IS CIRCUIT BOARD GRID REFERENCE. DESIGNATION IN PARENTHESIS DENOTES BANK NO. (1-3) AND CHIP NO. (1-8).

BANK 3 BANK 2 us INTERFACE INTERBOARD NNECTOR 1 | 3Ka1 q aKian q aKa) a

i BIBIEIBIEE

Figure 4. RAM Location and Numbering on CPU Board eo}

Page 9

TROUBLESHOOTING PROCEDURES: DIAGNOSTIC MODE TESTS

ROM BOARD LEDS RECOGNIZE CONDITION

ROM “2” means ROM error

RAM “I” means RAM error ROM BOARD LEDS IDENTIFY BAD CHIPS. VIDEO REMEDY

2-digit ROM chip no “ROM ERROR” and ROM chip no.

Bank no. “RAM ERROR” followed by RAM bank first... then chip no. and chip no. (Note: with multiple no. in bank (see RAM failures this display may not appear) figure 4)

  • Turn power off.
  • Replace suspected chip.
  • Check for these normal voltages on indicated RAM chip: -S/pin 1, + 12/pin 8, +Sipin 9.
  • Turn power off.
  • Replace suspected chip.
  • With muttiple RAM failures always check power supply. See POWER-UP TESTS.

CMOS (see appendix A) “3” means CMOS RAM error “CMOS RAM ERROR OR WRITE PROTECT FAILURE”

  • With power off, check pin 18 of CMOS RAM for 3.2VDC minimum. If present, replace CMOS chip IC. If absent, replace AA alkaline cells.
  • With new alkaline cells and power off, check for 3.2V minimum at pin
  • If still absent, replace diodes D9 and DIO.
  • Upon power-up and reentry into diagnostics if CMOS error message persists, check CMOS RAM memory protect and address decoding circuits with a logic probe.

Tests 4 and 7 provide sequential subtests. To stop automatic cycling set switch to MANUAL-DOWN. Depress ADVANCE in MANUAL-DOWN to step through subtests. LED indications are not made for these tests.

TEST & PROCEDURES

SOUND (Test 4)

SWITCH (Test 5)

  • Set switch to MANUAL-DOWN and clear any stuck switches.
  • CRT should indicate no switches closed.
  • Operate switches and check for display of switch name. VIDEO REMEDY OR ADJUSTMENT

“SOUND LINE 1” “SOUND LINE 2” “SOUND LINE 3” “SOUND LINE 4” “SOUND LINE 5” “SOUND LINE 6” (These appear one at a time.) auawne MISSING CHECK 2P4/10P3 pin 3 2P4/10P3 pin 2 2P4/10P3 pin 5 2P4/10P3 pin 4 2PA/10P3 pin 7 2P4/i0P3 pin 6 perform Sound Board Diagnostics (see below)

NOTE: If any two sounds are the same, sheck for a short between the select lines with the same sound. all

CRT indicates AUTO-UP closed and any stuck switches. CRT Display for Each Switch...

  • COIN DOOR SWITCH STUCK: Disconnect 2P3
  • PLAYER PANEL SWITCH STUCK: Disconnect 3P2 or 3P3. Coin Door Player Panel

ADVANCE 1-PLAYER START AUTO-UP- 2-PLAYER START HIGH SCORE RESET MOVE 1 LEFT COIN (next to hinge) FLAP 1 CENTER COIN MOVE 2 RIGHT COIN FLAP 2 SLAM SWITCH

  • COIN DOOR SWITCH DOES NOT OPERATE: Ground corresponding pin of 2P3.
  • PLAYER PANEL SWITCH DOES NOT OPERATE: Ground corresponding pin of 3P2 or 3P3, C.SYMPTOM REMAINS SAME ... ROM Board or Interface Board faulty. () SYMPTOM CLEARS UP ... Problem is in switches or wiring.
Page 10

MORE DIAGNO:

TEST & PROCEDURES

COLOR RAM (Test 6)

Note that a blank sequence or two sequences with the same shade indicate a faulty 1A flip-flop, 1B RAM or 2B

RAM or a failure in the color analog circuit. Check

voltages on QI (green transistor), Q2 (red transistor) and Q3 (blue transistor). During the eight full-screen color tests, the base voltage (center pin) on each transistor should vary between 3.8V (brightest color) and 4.4V (no color).

Color RAM Check

  • CRT sequences through 8 colors, 2 seconds each.
  • Thick vertical band indicates color RAM fault.

MONITOR & COLOR RAM (Test 7) Zrean

Color Bar Pattern IC MODE TESTS

VIDEO SEQUENCES

1 light red screen 2 red screen 3 dark red screen REPLACE RAM IB

too-light or too-dark red or gray band REMEDY OR ADJUSTMENT

REPLACE RAM 2B

magenta band

4 light green screen 5 green screen 6 dark green screen yellow band cyan band

7 light blue screen 8 blue screen magenta band too-light or too -dark blue or gray band

4 light green screen green band dark green band or gray band

5 green screen light green band dark green band or gray band

6 dark green screen

cross hatch pattern linearity, conver} focus. Aids you in setting up vertical and horizontal gray band

gence, and

red screen green screen blue screen color pattern Aids you in opti color purity. imizing

color bars + double-width + half-width

  • transposed
  • missing fault in 1A, 1B, chips. L If color RAM test 6 indicates no faults, symptoms at left suggest a 2B or 2C
Page 11

SOUND BOARD DIAGNOSTICS

SYMPTOM TEST & PROCEDURES MISSING SOUNDS; (1 CHECK SOUND-SELECT INPUTS NO SOUND (1) Turn power on.

  • Depress DIAGNOSTIC pushbutton on bottom of Sound Board. Sounds may be produced now even though absent in Diagnostic Mode Test 4. If you hear game sounds, proceed with this checkbox. If not, go ahead to POWER SUPPLY checkbox below.
TESTTOOLCONDITION & REMEDY

Sound Board connector 10P3/J3-1 logic probe (game on and in Test 4) | * PULSING-proceed 106 + LOW-check jacks, foils

  • STILL LOW-perform ROM BOARD checkbox below
SRI DIP resistors R3-R9VOM-reading ohms (game of)+ ALL 4.7K-proceed

+ ANY OPEN-teplace SRI

C39VOM-reading ohms (game of)+ ALL OKAY-proceed

+ ANY SHORTED-replace bad IC5-1, 1C7-14 logic probe (game on and in Test 4) | + HIGH-proceed (power pins) + LOW-replace C19 (IC5) or C21 (IC7) + STILL LOW-replace bad IC

IC5-2, 4, 6, 10, 12, 15; IC7-4, 6logic probe (game on and in Test 4)|» PULSING-proceed

+ LOW-replace chip IC10-18 and 19 logic probe (game on and in Test 4) | + PULSING-proceed (PIA) + LOW-lift C20, retest + PULSING NOW-replace C20 + STILL LOW-replace IC6, retest IC10-10 to 17 logic probe (game on and in Test 4) | + PULSING-proceed (PIA) + SOME LOW-teplace IC

  • ALL LOW-lift C31, retest
  • PULSING NOW-replace C31 + STILL LOW-replace IC SOUND WHEN OO CHECK ROM BOARD OUTPUTS POSTIBO ETO N PRESSED (1) If you hear game sounds, disconnect and then reconnect Sound Board connector 10P3/J3.
  • You should hear one or more game sounds. If so, put game in Diagnostic Mode Test 4 and proceed with this, BuT NOT iN Mane checkbox. If not, go ahead to POWER SUPPLY checkbox below.
TEST 4TESTTOOLCONDITION & REMEDY

ROM Board connector 2P4/14-3 logic probe (game on and in Test 4) | + PULSING-repair cable to Sound Board to 6 + ANY LOW-repair jack or foil, proceed

OC DIP resistors 2 to 6VOM-reading ohms (game off)+ ALL 4.7K-proceed

+ ANY OPEN-replace 0C

26-39VOM-reading ohms (game off)+ ALL OKAY-proceed

+ ANY SHORTED-replace bad ICIC-10 to 15 (PIA) logic probe (game on and in Test 4) | + PULSING-proceed

  • SOME LOW-rteplace IC + ALL LOW-lift C23, retest
  • PULSING NOW-replace C23 + STILL LOW-teplace IC DI CHECK ON-BOARD POWER SUPPLY
  • With power off, test for fuse continuity at Fl and F2.
  • With power on, check for +12V unregulated DC at TPI and at pin 5 of ICI.
  • Now check for +5V regulated DC between TP4 and TP3, If voltages are absent or low, turn off game and lift one pin of filter capacitors C25, C26 and C27
  • Check each with ohmmeter for possible shorts.
  • If capacitors are good and unregulated voltages test okay but you're missing +5V, replace regulator chip (IC8) DO CHECK AUDIO (ANALOG) SECTION
  • Turn power on; turn up volume control. Momentarily place powered-up AC soldering pencil on final amplifier’s input pin (ICI, pin | or 10P4, pin 2). If you hear low hum, audio IC, volume pot and speaker are okay.
  • Repeat test at Q2 emitter. If you hear hum. analog section is okay. Step (1) will also work if you simply touch amplifier’s input pin, However output level of hum will be much lower than with soldering iron. DO NOT use a soldering pencil of over 40 watts. Cordless models will NOT work here. 1 CHECK SOUND ROM 12 AND RELATED CIRCUITRY
  • Is Jumper WI connected? IT SHOULD BE on all Joust games, or sound signals from the D/A converter (IC13) will never arrive at input of impedance-matching transistor Q2
  • Turn power on.
  • If you have no game sounds but power supply tests show normal voltages and no ripple on +5Y. check crystal clock circuit. Using DVM or logic probe, test for pulsing AC across crystal. If clock signal's absent, replace crystal and associated capacitors.
  • Turn power off.
  • Swap sound ROM (ICI2) and then microprocessor chip (IC9) with known-good chips.
  • Power-up and test Sound Board after each swap by pushing DIAGNOSTIC button NO SOUND

STILL NO SOUND

MISSING SOUNDS; NO SOUND

Page 12

APPENDIX A

CMOS RAM Data Test Protocol

The first sub-test of the CMOS RAM oO data is that of the ATTRACT MODE MESSAGE checksum. If the test does not pass, the factory ATTRACT MODE MESSAGE is restored. Next, the game adjustments are checked and restored to factory settings if an error is found. If game adjustments are found intact, the high score table is checked for any bad entries. Bad entries are replaced a score of 4,000 points and no initials. If all entries check, the game returns to the Game Over Mode. ATTRACT MODE MESSAGE?

Fal

If game adjustments are restored to factory settings, the AUDIT TOTALS are checked. If 5 or more audit digits are other than 0-9 (that is hexadecimal FAIL A through F) all audit totals are cleared. This is followed by a check of the high score table and the table is reset to factory settings if errors are found. Finally, game adjustments are rechecked and either OPEN COIN DOOR or FACTORY SETTINGS AUDITS RESTORED is displayed. With the former, open the coin door and turn the game OFF and ON and then FAC- 5 OR MORE HEX AF TORY SETTINGS RESTORED wiil be displayed. Return to game over by depressing the ADVANCE pushbutton or by turning the game OFF and ON a second time. oom ADJUSTMENTS

RESTORE FacTORY SETTINGS, HIGH SCORE ENTRIES.

BAD ENTRIES. REPLACED WITH 4,000 AND NC INTIS. PASS

TINITAL TESTS INDICATE ALL SYSTEMS GO DISPLAVEE

HIGH SCORE TABLE

RESET HIGH SCORE TABLE To FACTORY SETTINGS.

"OFEN COIN DOOR" se DISPLAYED RESTORED" DISPLAYED

OPEN coin 0008 POWER OFF AND ON

  • 0) POWER OFF AND ON
Warning—This equipment generates. uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. Ithas been tested and found te comply with the imits for a Class A computing device pursuant fo Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense Will be required to correct the interference. STD 796