Missile Command TM-147 3rd Printing
Missile Command (rev 3, A035467-02/04 PCBs) (Atari, 1980) · Technical Manual · 52 pages · 53 sections · original scan
oct (MUMS J ILE Complete with lilustrated Parts Lists
oa (el N=jU WUeD (mM
GAME SERIAL NUMBER LOCATION QO
Your game’s serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator/Audio II PCB, and game PCB. Please mention this number whenever calling your distributor for service.
GAME SERIAL # IDENTIFICATION TAG
TV MONITOR
xe ® REGULATOR/AUDIO Il PCB
GAME PCB
VILFILE CONAN
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists
Published by: ATARI ING 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086
Copyright © 1980 by Atari, Inc. All rights reserved.,
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. ea \ i
Lithographed inthe USA. 9J Cw] ‘A Watner Communications Company
Table of Contents
1 Location Setup A. New Parts... B. Game Inspection . C. Game Installation. .
- Voltage Selection .......
- Interlock and Power On/Off Switches D. Self-Test Procedure ................ E. GamePlay ......
- Attract Mode....
- Ready-to-Play Mode
- PlayMode .......... 4. High Score Initial Mode ..........--..0.e eee eee
2 Maintenance and Repair A. Cleaning B. Fuse Replacement. C. Opening the Control Panel .
- LED Switch Replacement.....
- Trak Ball™ Maintenance and Repair TV Monitor Replacement....... Printed Circuit Board Replacement Opening the Attraction Panel ...
- Replacing Speakers .....
- Replacing Fluorescent Tube .. G. Coin Door Repairs ........0....08 H. Game Operation mmo
3 Illustrated Parts Lists ODODOOCMAWWWW+
List of Illustrations
Figure 1 Overview of Game... cece nee eee eee rs Figure 2 Installation Requirements . 3 Figure 3 Power Supply 4 Figure 4 Interlock and Power On/Off Switches ............0. 0.00 e cece 5 Figure 5 Location of Self-Test Switch, Volume Control and Option Switches .... . 6
Figure 6 Self-Test Procaqure oes ic cece cst eee ee teeta eee ence eeeeaecte 7 Figure 7 Option Switch Settings 8 Figure 8 Opening the Control Panel and Replacing Switches . . 12 Figure9 Trak Ball™ Maintenance and Repair ........... -. 13 Figure 10 TV Monitor Removal ..........0 66. c ccc cent eee ce ee 14
Figure 11 Game and Regulator/Audio |! PCB Repiacement ..................05 15 Figure 12 Opening the Attraction Panel............... . 16 Figure 13 Removing and Reinstalling a Coin Mechanism . Figure 14. Switch and Trip Wire Replacement . o7 Figure 15 Coin DoorLamp Replacement .............. 000.0 e cece cece eee
Figure 16 Power Distribution Figure 17 Signal Distribution
illustrated Parts Lists: Figure 18 Cabinet-Mounted Assemblies ........... 6.6.0. e cece eee ene ees 24 Figure 19 Attraction Panel and Fluorescent Light Assemblies .. 28 Figure 20 Control Panel Assembly ........ 20.60 c cece eee e cenit eee eens 27
Figure 21 Trak Ball™ Assembly .........0. 0000 ccc eee cece ete n ences 28 Figure 22 Steering Printed-Circuit Board Assembly . .. 30 Figure 23. Type B Power Supply Assembly... .. . .. 31 Figure 24 NewCoinDoor.......... . 32 Figure 25 Game PCBAssembly......... .. 36 Figure 26 Regulator/Audio Il PCB Assembly + 40
a™ Missile Commant
If reading through this manual does not lead to solving a certain maintenance problem, call Telie-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.
WEST and CENTRAL U.S.A.
Parts for all Atari Customers. Sales and Service
Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103
(Monday - Friday, 7:30 - 4:00 pm Pacific Time)
- From California, Alaska or Hawaii ™ (408) 745-2900
From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A.
Sales and Service Only
Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)
= From New Jersey (201) 469-5993
Zz From anywhere else in this area toll-free (800) 526-3849
Location Setup
A. New Parts
The Missile Command™ game has four new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: @ Color TV Monitor. Made especially to Atari specifications, the 19-inch monitor has been color-converged at the factory. All convergence adjustments are cemented and locked in place, to prevent accidental changes. This helps provide higher reliability for the service technician. @ Isolation Transformer. The color TV monitor chassis in this game does not contain an isolation transformer. Atari has mounted an isolation transformer on the floor of the cabinet to protect operators. If you service this color TV on a test bench, you must isolate the line voltage! (See instructions on pages 14-15.)
ATTRACTION PANEL COLOR TV MONITOR
TV MONITOR SHIELD S
REGULATOR! AUDIO Il PCB
CONTROL PANEL
GAME PCB
TRAK BALL™ CONTROL
POWER SUPPLY
POWER ON/OFF SWITCH
Figure 1 Overview of Game
@ Regulator/Audio Il PCB. This slightly redesigned printed-circuit board has two additional voltage regulators for games using 2708 EPROM memory chips. The board’s new + 12V and —5V regulators are both mounted on the heat sink. Otherwise this board is the same as past Regulator/Audio PCBs. @ New Coin Door. This door will accomodate two or three mechanisms, and up to four coin counters. Its triple-arm locking bar provides added security. For greater ease of access, the self-test switch is now mounted on the door, rather than inside the cabinet.
These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is
mentioned, you will see this symbol: i *s.))
B. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
C. Game Installation
Figure 2 Installation Requirements
Power 150 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 64 x 83 cm (25% x 32% in.) Game Height 186 cm (73% in.)
- Voltage Selection
Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.
Line Voltage Range Voltage Selection Plug Color
86-104 VAC (95) Black 100-125 VAC (110) Orange 190-220 VAC (205) Green 210-240 VAC (220) Red
- Interlock and Power On/Off Switches
To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door or panel is opened.
Check for proper operation of the interlock switches by performing the following steps: @ Unlock and open the access panel and the coin door. @ Plug the AC line power cord into an AC outlet.
Line Voltage Range Voltage Selection Plug Color 86-104 VAC (95) Black 100-125 VAC (110) Orange 190-220 VAC (205) Green 210-240 VAC (220) Red
VOLTAGE SELECTION PLUGS POWER-SUPPLY CHASSIS.
Figure 3 Power Supply
@ Close the access panel and coin door. @ Set the power on/off switch to the on position. Within approximately 30 seconds the TV monitor should display a picture. @ Slowly open the rear access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door. @ If the results of the previous step are satisfac- tory, the interlock switches are operating properly. If the TV monitor doesn’t go off as de- > A
scribed, check to see if the corresponding in- c 'sS
terlock switch is broken from its mounting or stuck in the on position.
POWER ON/OFF SWITCH
SWITCH COVER
SAFETY INTERLOCK SWITCH
Figure 4 Interlock and Power On/Off Switches
‘VOLUME CONTROL VOLUME DECREASE: TURN CLOCKWISE
SELF-TEST SWITCH
OPTION SWITCHES
Figure 5 Location of Self-Test Switch,
Volume Control and Option Switches
D. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game's circuitry and controls are operating properly. The data is provided on the TV monitor and the game speaker; no additional equipment is necessary.
Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options.
To run the self-test, follow the instructions outlined in Figure 6.
Instruction Figure 6 Self-Test Procedure
Result if Test Passes Result if Test Fails
- Set self-test switch to on position (see Figure 5). Note: entering self-test will set the HIGH SCORE TODAY display to 7500.
- Roll the Trak Ball control in all directions.
- Press the following switches: @ Coin switch trip wires @ Coin door slam switch @ All three fire switches @ Player start buttons
- Set self-test switch to off position. After about 5 seconds of frozen attract mode, a low raspy tone is followed by a low beep, then high beep. TV monitor screen displays picture as shown below: ROM OK MAP OK RAM OK + ..Pplus the options display—see Figure 7 for explanation. Both LED start buttons will also be lighted.
The + moves around on the screen in directions corresponding to Trak Ball control—up to an invisible border along the screen's edges.
Asound is heard as each switch is pressed. The background color also changes. A continuous raspy tone means V BLANK is malfunctioning. Self-test will not continue. A RAM failure is indicated by a blank or “garbage”-filled screen and a repeated series of 8 beeps, separated by a low raspy tone. See note 1 below. Self-test will not restart. ROM failure is indicated by BAD ROM; see note 2 below. BAD MAP means bit-mapping hardware has failed. BAD CHIP means custom audio I/O chip at location P8/9 has failed.
The + doesn’t move in same direction as ball, or not at all. One of the Steering PCBs on Trak Ball control may be bad, harness wires or connector may be loose, Trak Ball reading circuitry on Game PCB may be bad, or Trak Ball bearings may need oiling.
No sound or color changes are produced when pressing one of these switches: indicates a bad switch, loose harness wires, or loose connector.
Figure 7 Option Switch Settings
To change toggle positions cn the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the game PCB is mounted in place. When changing the options, verify proper results on the TV monitor display by performing the self-test. Note that changing an option on any toggle wiil cause an immediate change on the TV monitor screen during the self-test.
Toggle Settings of 8-Toggle Switch on Game PCB (at R10) (RIGHT switch when PCB is in game)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
| On | On | 1 coin* for 1 play | ||||||
| oft | Cn | Free play | ||||||
| On | Oft | 2coins* for1 play | $ | |||||
| Off | Off | 1 coin* for 2 plays | ||||||
| On | On | Right coin mech x 1 | $ | |||||
| z | On | Off | Right coin mech x 4 | |||||
| 3 | Off | On | Right coin mech x 5 | |||||
| Off | off | Right coin mech x 6 | ||||||
| s | On | Center coin mech x 1 | $ | (Center mech is a left | ||||
| Zz | Off | Center coin mech x 2 | mech in a 2mech door) | |||||
| On | On | English language | ||||||
| On | Oft | French language |
Off On German ‘anguage
| Off | Off | Spanish ianguage |
Toggle Settings of 8-Toggle Switch on Game PCB (at R8) (LEFT switch when PCB is in game)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
| Oft | Off | Game starts with 7 cities | ||||||
| On | On | Game starts with 6 cities | $ | |||||
| Off | On | Game starts with 5 cities | ||||||
| On | Off | Game starts with 4 cities |
vrOn No bonus credit vy Off 1 bonus credit for 4 successive quarters or a $1.00
| 8 | coin | § |
| 8 | Off | Large Trak-Ball input (switch must be off for proper |
operation of upright Missile Command game) $
| a | oft | off | On | Bonus city every 8,000 points | |
| 3 | On | On | On | Bonus city every 10,000 points | $ |
| On | On | Off | Bonus city every 12,000 points | ||
| On | Off | On | Bonus city every 14,000 points | ||
| On | Off | Off | Bonus city every 15,000 points | ||
| Off | On | On | Bonus city every 18,000 points | ||
| Off | On | Off | Bonus city every 20,000 points | ||
| Off | Off | Off | No bonus city |
The format of the seif-test display is as follows:
Bonus city every points (line disappears if no bonus city is chosen) + Coinage setting 4, 5, 6, or 7 cities (always in English) A 8B cD
A is the center mech multiplier for 3-mech doors, ‘eft mech multiplier if a 2mech door. This number is either 1 or 2. B is the right coin mech muttiplier and is 1, 4, 5, or 6. Cis an “F” if switch 4 (of R8) is off. Dis an “X” if switch 3 (of R8) is off. An example of an actual option switch display is as follows:
BONUS CITY EVERY 10,000 POINTS + 2 COINS 1 PLAY 6 CITIES 1 1 FX
- In the U.S., a “coin” is defined as 25°. if your game also has a $1 mechanism, you must set the right coin mechanism multiplier as per your choice.
$ Manufacturer's suggested settings + This option available only if game PCB has -02 memory installed.
E. Game Play
Missile Command™ is a 1- or 2-player game with a color monitor. The game depicts an Armageddonstyle war in which players defend their bases and cities with antiballistic missiles (ABMs). The enemy—the game computer—launches incoming waves of attack missiles. These weapons may be either individual or branching attack missiles. In addition, the enemy occasionally launches missiles from a fast-moving “killer” satellite or from bombers. The enemy also launches “smart” missiles that usually avoid explosions.
Players receive varying numbers of points for intercepting attack missiles, for having unused missiles still in their bases’ arsenals, and for having their cities undamaged after a missile wave.
The game has five possible modes of operation: attract, ready-to-play, play, high-score initial, and self-test. The latter is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled, and the “HIGH SCORE TODAY” is reset to 7500. A list of eight “highest” scores and initials are also reset onto the screen (to provide player challenge).
- Attract Mode The attract mode begins when power is applied to the game, after a play or high-score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted, or when entering self-test.
In this mode, the Missile Command name is displayed, then the computer plays one wave—handling both offense and defense. Following this, the computer displays the high score table, then the Missile Command graphics reappear.
- Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START pushbutton is pressed.
When this mode begins, the message PRESS START scrolls along the bottom of the screen. DE- FEND CITIES and red arrows pointing down to each city also appear on the screen. The displayed pictures are otherwise the same as those shown in the attract mode.
- Play Mode The play mode begins when either start pushbutton is pressed. The mode ends when the player's last city is destroyed.
The three bases— Alpha, Delta and Omega—each have 10 ABMs ready to be fired (shown as z's). Players must be careful to fire the missiles more or less evenly from among those bases, because no more missiles are granted until the screen resets in preparation for a new wave of attack missiles. If the enemy missiles strike a city or base, the colorful buildings or base will change to the solid color of the landscape.
The game continues until all cities are destroyed. Missile Command™ has no operator-selectable fixed time length. Thus a highly skilled player can play longer than the novice.
During the second wave, a “killer” satellite and/or bomber will appear on the screen, moving quickly and launching attack missiles at the bases and cities. Players get bonus points for shooting down the satellites or bombers.
The general approach for getting high point scores is fairly quickly discovered: try to launch your ABMs when the enemy missiles have just appeared at the top of the screen. Then they are clustered together, where one ABM can usually destroy several enemy missiles. In the later more advanced waves, players can lay out a blanket of explosions.
- High Score Initial Mode If a player's score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. Spinning the Trak Ball control changes the letters (A thru Z and a blank are available). Pressing any fire switch will fix that letter on the screen, and move the choice to the next letter. If the player doesn’t enter his or her initials within 90 seconds, three blank spaces will be entered automatically.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance and Repair
The Missile Command™ game requires certain maintenance to keep it in good working order. Clean, properly maintained games attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if the Trak Ball™ control or light-emitting-diode switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the Trak Ball control: for details see this chapter.
A. Cleaning
The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.
B. Fuse Replacement
This game contains six fuses—all on or near the power supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as listed in Chapter 3 of this manual: the single fuse mounted on the floor of the cabinet and the five fuses on the power supply are all described in Figure 23. See the color TV monitor manual, TM-160, for the monitor fuse data.
L.E.D SWITCH: TO REMOVE TURN COUNTERCLOCKWISE
NORMALLY CLOSED (N.C.) CONTACT —
NORMALLY OPEN — (N.O) CONTACT
LIGHT-EMITTING DIODE (LE.D.) CONTACTS ° COMMON CONTACT
C. Opening the Control Panel
Prior to repairing or replacing any switch or the Trak Ball™ on the control panel, or prior to removing the TV monitor, unplug the game. Then open the coin door.
Reach through the opening and remove both sets of carriage bolts and lock nuts, located on the underside of the conirol panel (see Figure 8).
Lift up on the control panet and tilt it towards you. Be sure that the acrylic TV monitor shield does not fall on you. The top edge of the control panel acts as a retainer strip for the shield: once the control panel is opened, the shield is free and could slide out by its own weighi.
Figure 8 Opening the Control Panel
Disassemble in the order indicated. (Circled numbers match the steps described below.)
Ball Replacement
- Remove the entire Trak Ball assembly as shown in the previous figure. Locate the three countersunk machine screws in the acrylic top plate; remove these screws. (When the assembly is installed, these three screws are right underneath the control panel.)
- Remove and replace the ball.
Steering PCB a
Steering PCB Replacement
- Remove the hardware holding down the black toothed wheel (the light hub); lift this wheel off of the black roller shaft. Unplug the connector ‘on the steering PCB. Remove the two cross-recessed machine screws, brown spacers and lock nuts from the steering PCB. 4, Remove the steering PCB.
- When replacing this PCB assembly, be certain that the black toothed wheel turns freely between the two halves of the red photosensor device. LUBRICATE THIS BEARING (1 OF 5 PLACES)
Trak Ball Lubrication
- Open control panei as illustrated in Figure 8.
- Unplug the contro! panel harness connector.
- Apply only 2 drops of 3-in-One® oil in each of the ball bearings. (Each Trak Ball control has five bearings.) Tilt the panel to its closed position and roll the ball in all directions. Be sure the oil has not spread onto the shafis—otherwise your players will get oily hands.
Figure9 Trak Ball™ Maintenance and Repair
- LED Switch Replacement
The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 8.
@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to R x 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 8 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ = Ifthe contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
- Trak Ball™ Maintenance and Repair To maintain this control, you will only have to lubricate the bearings approximately every 2,000 credits. The number of credits can be read off the coin counter, located on the coin door. Use only 2 drops of 3-in-One® oil in each of the ball bearings. (The Trak Ball control has five bearings.)
For further instructions on how to replace the Trak Ball or either Steering PCB, see Figure 9.
(May be 1 or 2 shields)
Disassemble in the order indicated, (Circled numbers match the steps in Section D.)
Figure 10 TV Monitor Removal
On
D. TV Monitor Replacement
4.
If you should need to service or replace the color TV monitor, you must first remove it from the game cabinet. Follow the instructions below, and refer to Figure 10. Open the control panel! as described in Section C, Opening the Control Panel. Be sure the game is unplugged from its wall outlet! Unlock and remove the access panel. Slightly loosen the wing nuts above the TV monitor (inside the game) that secure the upper retainer strip. Remove the two acrylic TV monitor shields by sliding their lower edges out. Working up from the bottom side corners, carefully pry loose the two side flaps of the colorful cardboard bezel. (A 4-inch strip of double-sided adhesive tape is centered behind both side flaps, flush with each edge.) Open the access panel and unplug the harness connectors for the TV monitor: one is a 2-pin connector in the harness, the other is a 6-pin connector on the monitor's printed-circuit board, Be extremely careful and never touch the red anode wire or the high-voltage tube on the rear of the monitor! Then unscrew the green ground wire that is attached to the TV monitor chassis. Also unplug the harness connector for the fluorescent light (located at the left side of the cabinet’s rear opening).
- Remove the four sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the metal TV chassis.
- Carefully slide the TV monitor chassis out the front of the game. After replacing a monitor, be sure to run the self-test.
A: DANGER
The color TV monitor does not contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the color monitor on a test bench, you must isolate the monitor from AC voltage with an isolation transformer.
E. Printed Circuit Board Replacement
You may wish to remove the game printed circuit board (PCB) or the Regulator/Audio II PCB for service or inspection. To do this, refer to Figure 11 and proceed as follows: a Open the access panel. Locate the securing screw and fiber washer that hold down the PCB in its slots, and remove them. (Each PCB has one set of this fastening hardware.) If you are removing the game PCB, first remove the two beaded tie wraps that hold the edge connector to the game PCB’s edge. Then unplug the edge connector from the game PCB. If you are removing the Regulator/Audio II PCB, simply disconnect the three small harness connectors on this board. Carefully slide either PCB straight out of its slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. Reinstall the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty.
Figure 11 Game and Regulator/Audio Il PCB Replacement m
REGULATORI/AUDIO II PCB
GAME PCB
UPPER
SPEAKER 8 RETAINER STRIP
ATTRACTION PANEL
FLUORESCENT TUBE
Figure 12 Opening the Attraction Panel
°
F. Opening the
- Replace the securing screw and fiber washer in .
the PCB. Reinstall the tie wraps into the edge Attraction Panel
. id lock th eee panel afie’ PGB: (lose and: Inck the ae Prior to replacing the fluorescent tube behind the . . attraction panel, you will first have to remove the
- Check that the operation of the game is correct graphics attraction panel at the top of the Missile
wi a ja PCB. Normally thy only adjustments Pa the Unplug the game; then remove the three Allen- Missile Command™ game are option switch head screws at the top of the game. They secure the changes (made on the 8-toggle DIP switches). metal retainer strip for the attraction panel. Remove an Unless you are qualified technician, do not turn _the retainer competely. the small knob on the Regulatot/Audio II PCB, Tilt the top of the attraction panel towards you, For information pertaining to this control, refer then lift it up and out of the bottom retainer (see to schematic drawings DP-147-01 and -02. Figure 12).
If you have to replace the attraction panel, you will Probably not be able to remove and save the two wood speaker blocks on it. Be sure to order these blocks, in addition to the attraction panel (see parts list in Figure 19).
- Replacing Speakers First disconnect the harness plugs for the speakers. Then place the attraction panel on a smooth clean surface, so you don’t scratch the acrylic panel. Replace the speaker, then reconnect the harness connectors.
- Replacing Fluorescent Tube
First remove the colorful attraction panel as previously described. Then replace the white fluorescent tube by following this procedure (see Figure 12).
@ Remove the two Y-shaped connectors from the ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you. @ Replace with anew tube. Do not snap the tube in vigorously—you may break it, causing an implosion! @ Close up the game by replacing the attraction panel, retainer strip, and three Allen-head screws.
G. Coin Door Repairs
The new Atari coin door has been totally redesigned, as described on page 3 of this manual. For ease of maintenance, the coin door mechanisms require no adjustments. For plastic mechs, use only hot soapy water to clean them: boiling water is not needed nor even recommended, as this would soften the plastic.
To remove any mechanisms, or to replace the small lamps, switches or trip wires, follow the illutrations and instructions given in Figures 13 through
- To obtain part numbers for ordering purposes, refer to the detailed exploded drawing of the coin door and parts list in Figure 24.
COIN MECHANISM
Open coin door. To clean or replace a mechanism, locate the black spring clip above the coin switch. Pull this clip towards you, then swivel it up 90°. Push the mechanism towards the right, then pull it out. When reinserting the mechanism, be certain that no wires get caught up in it. Align the mechanism between the top and bottom pairs of vertical tabs in the inner door panel. Push the part of the mechanism closest to you to the left, ‘so both of its round studs slip into the curved notches on the inlet and return chutes. Turn the black spring clip down again to secure the mechanism in place.
Figure 13 Removing and Reinstalling a Coin Mechanism
SWITCH COVER
QUICK-DISCONNECT > WIRES,
QUICK-DISCONNECT Remove the plastic switch cover by squeezing together its two prongs (Just underneath the switch). Tilt the bottom edge of the cover out to the right while pulling towards you and up.
Unplug the quick-disconnect wires on the switch and lockout coil. Use a longer-style 4” socket wrench, so you won't damage the trip wire, and remove both nuts that secure the coin return chute onto the inner panel. Now hold the return chute subassembly together in one hand, and replace the defective switch. The trip wire can be replaced by carefully prying up the black internal-tooth retainer with a small flat screwdriver. Then remove the wire from the brass-colored stud. Be sure to replace the wire with another of the proper color (four are available, depending on coin denomination). If the new wire is loose when placed on the stud, squeeze the stud’s two halves together with a pair of pliers to secure the wire. Then replace the retainer. Make certain that the wire projects thru the entire width of the coin slot: otherwise no credits will be granted, even for genuine coins. The wire’s normal rest position is against the top of the curved slot.
TRIP WIRE
SWITCH \ RETAINER
Figure 14 Switch and Trip Wire Replacement
COIN INLET CHUTE
LAMP BRACKET @ Remove the screw that secures the lamp and its “Z” bracket to the coin inlet chute. @ Replace the burned-out bulb. Then mount the lamp holder bracket back on the coin inlet chute.
Figure 15 Coin Door Lamp Replacement
H. Game Operation
With this manual you received two large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.
Missile Command™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the TV monitor, Regulator/Audio li PCB, loudspeakers, and control panel.
The Regulator/Audio Il PCB performs two functions: 1) it regulates the +10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio II PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio Il PCB directly drives the game speakers and is controlled by the volume control, mounted inside the coin door.
The Power Supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power supply chassis.
Figure 16 illustrates the distribution of power in this game. Figure 17 illustrates the distribution of signals.
FLUORESCENT LIGHT
COLOR MONITOR
CONTROL PANEL ASSEMBLY
INTERLOCK SWITCHES. ys)
REGULATORI/AUDIO |i PCB
&
COIN DOOR GAME PCB
POWER SUPPLY
POWER CORD a
ISOLATION TRANSFORMER
ON/OFF SWITCH
Figure 16 Power Distribution
SPEAKERS
“SS
COLOR MONITOR
CONTROL PANEL
TRAK BALL
-~S
REGULATORIAUDIO II PCB
VOLUME CONTROL
SELF TEST SWITCH
GAME PCB
oN
COIN DOOR’
AUDIO
VIDEO. VSYNC HSYNC
TRAK BALL INPUTS
Figure 17 Signal Distribution
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
llustrated Parts Lists
The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Atari Missile Command™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists have been arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00-thru 99-, then 000598- thru approximately 110000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Attraction Panel Assy. and Fluorescent Light— See Figure 19 70-304 (Fluor. Tube)
035397-01 (Upper Retainer)
035398-01 (Lower Retainer)
y 4] Yi 035403-01, 035414-01 (Monitor Shields) Control Panel Assy. vi 7 j | See Figure 20
See Figure 21
See Figure 24 035387-01 (Geze!)
\ 68.002 (Interl. Switch)
002728.01 (Ctrl. Panel Brkt.)
Trak Ball™ Assy.—
: A035791-01, -02, -03 (isol. Transformer) p New Coin Door— -S \ a
92.049 (Monitor)
007882.01 (Interl. Switch Cvr.) 035745-03 (Retainer) A035802-01 (Main Harness)
m Regulator/Audio li PCB Assembly— See Figure 26
Game PCB Assy.— See Figure 25
7507017 (PCB Spacer)
034536-02 (Foam) '035745-02 (Retainer)
- -A034631.04 (OniOtf Switch) A033016-02 Type B Power Supply Assy.— OR A033958-02 See Figure 23 (Power Cord)
19-0092 009992.01 (Vol. Control) (On/Off Switch Cvr.) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL; Reproduction forbidden without the specific written permission of Atan, Inc. Sunnyvale, CA ‘hi drawing evenly conatonay' ised, ana neither receip! nor possession thereo! confersor transters any A021700-xx & figntin. or leanse to use the Subject matter of the cram. (Coin Box) 00687001 ~~ 78.3901 ing ran aesion or techicalinfermation shown therecn, ‘ nor any sight to reproduce this drawing or any part 030249-01 (Coin Box Brkt.) (Cab.-Leveling Leg) thereot” Except for manufacture by vendors of Atar, Inc. (Separator) and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.
Figure 18 Cabinet-Mounted Assemblies A035390-xx G
Figure 18 Cabinet-Mounted Assemblies Parts List
Part No. Description
A002465-01 Coin Counter
| A021700-01 | Coin Box Assembly | (for all the same coins) |
| A021700-02 | Coin Box Assembly | (for two different coin denominations—has one separator) |
| A021700-03 | Coin Box Assembly | (for three different coin denominations—has two separators) |
| A033016-02 | Strain Retief Power Cord | (domestic) |
| A033958-02 | Strain Relief Power Cord | (German) |
A034631-01 On/Off Switch Assembly A035791-01, -02 or -03 Isolation Transformer
| A035802-01 | Main Harness Assembly | (includes on/off switch, 2 interlock switches and their brackets, |
volume control and its bracket, and single-pole fuse block), The following four items are the technical information supplements to this manual:
| DP-147-01 | Missile Command™ Schematic Drawings | (Sheet 1) |
| DP-147-02 | Missile Command™ Schematic Drawings | (Sheet 2) |
ST-147 Label with Self-Test Procedure and Option Switch Settings TM-160 Instruction and Service Manual for GO7-901 R.G.B. Color Monitor 49-9032 Volume Control 68-002 Interlock Switch Assembly 70-304 18” 15-Watt Cool White Fluorescent Tube 71-2114 Panel Cartridge Lock Mechanism (for access panel) 75-07017 Spacer for Mounting Printed Circuit Boards 78-3201 Cabinet-Leveling Leg 78-24012 5" Beaded Nylon Tie Wrap 92-049 19” Color TV Monitor 00272801 Control-Panel Mounting Bracket 006870-01 Coin Box Bracket 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 030249-01 Coin Box Separator 034536-02 Foam Vibration Damper for Game PCB 035387-01 Cardboard Bezel 035397-01 Upper Retainer Strip for Monitor Shield 035398-01 Lower Retainer Strip for Monitor Shield
| 035403-01 | 118-Inch-Thick Acrylic TV Monitor Shield | (smoke, no graphics) |
| 035414-01 | 1/8-Inch-Thick Acrylic TY Monitor Shield | (clear, with graphics) |
035745-02 18" Plastic PCB Retainer 036745-03 10" Plastic PCB Retainer
Fiuorescent Light, A035834-01: NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden witout the specific written permission of Atari, Inc.. Sunnyvale, CA This drawing is only conditionally’ issued, and neither receipt nor Possession thereof confers or transfers any fight in, oF license to use, the subject matter of the drawing or any design oF technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Ata‘, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or 79-561816P
the subject matter thereo! unless by writlen agreement with or written peimission rom the corporation
035386-01 99-11009
A005493-01
035407-01
035420-01 99-11011
Attraction Panel Assembly, A035411-01;
Figure 19 Attraction Panel and Fluorescent Light Assemblies A035411-01 (A) and A035834-01 (E) Parts Lists
Part No. Desctiption
Attraction Panel Assembly, A035411-01: A035804-01 Speaker Harness Assembly 48.004 5” 8-Ohm 5-Watt High-Fidelity Speaker 000869-01 5" Speaker Grille 03538601 Acrylic Attraction Panel with Graphics 035407-01 Wood Speaker Block 035420.01 Gasket Fluorescent Light, A035834-01: A005493.01 Fluorescent Light Harness Assembly 70-304 18” 15-Watt Cool White Fluorescent Tube 79-561816P Spring Connector Wire Nut for 16- to 18-Guage Wires 99-11003 Starter, Type FS2 99-11008 50/60-Hz Ballast Transformer, with 6"-minimum leads 99-11009 Starter Sockei, with 6”-minimum leads 99-11011 1¥%2” Clamp for White Fluorescent Tube 035835-01 12" Y-Lead Connector (2 required per light). Alternate is part no. A036045-01
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING NFIDENTIAL: Reproduction forbidden without the Specific walien permission of Atars Ine, Sumnyvale, CO This drawing is oniy conditionally issued, and neither receipt net possession thereof confers or transfers amy right in, oF license to use, the subject matter of the drawing oF any design or technical information shown. thereon, nor any right to reproduce this drawing or any pari thereof. Except for manufacture by vendors of Atar', Inc., and for manufacture under the corporation's wiitten license, no right to teproduce this drawing is granted or the subject matter thereof unless by written agreement -with or written permission from the corporation. Trak Ball Assy.— ‘See Figure 21
62-039
75-07054
\ 033127.01
A035803-01
Figure 20 Control Panel Assembly A035406-01 D
Parts List
Part No. Description
A035803-01 Control Panel Harness Assembly 62-039 SPDT Momentary Pushbutton Switch, with Red Cap and Light-Emitting-Diode 62-041 SPDT Black Momentary Pushbutton Switch 75-07054 Nylon Spacer 033127-01 Black Molded Switch Bushing 035384-01 Metal Control Panel with Graphics
A033360-01 Figure 21 Trak Ball Assembly G 85-1808B
Steering PCB Assy.
See Figure 22
75-0108 mY 9933355-01 034168-01
Figure 21 Trak Ball™ Assembly Parts List
Part No. Description
72-1006S #10-32 x 3/8" Cross-Recessed Pan-head Cadmium-Plated Steel Machine Screw 72-1408S #4-40 x ¥2" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-1806S, #6-32 x 3/8" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-8808 #8-32 x V2" Hex Socket-Head Cap Alloy Stee! Machine Screw 72-8920S #3/8-16 x 1%" Hex Socket-Head Cap Alloy Steel Machine Screw 73-3006 Carbon Spring Stee! External Retaining Ring, for 3/8” shaft diameter 74-A00011 Phenolic Spacer, 1/8” inside diameter x 4" outside diameter x %" long 75-010S #10 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-016S #6 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-018S #8 Flat SAE-Standard Zinc-Piated Steel Washer 75-040S #10 Steel Split Lock Washer 75-0418 #3/8 Steel Split Lock Washer 75-046S #6 Zinc-Plated Steel Split Lock Washer 75-048S #8 Zinc-Plated Stee\ Split Lock Washer 75-3608S #6-32 x ¥2" Cross-Recessed Flat-Head Cadmium-Plated Steel Machine Screw 75-916S #6-32 Standard Cadmium-Plated Steel Machine Hex Nut 75-919S #3/8-16 Standard Cadmium-Plated Steel Machine Hex Nut 75-990504C, #4-40 Shallow-Pattern Prevailing-Torque Corrosion Resistant Lock Nut 85-1808B #8-32 x ¥2” Socket Cap Flat Countersunk-Head Black-Oxide Steel Screw 000616-01 Light Hub 033355-01 Base Plate 033356-01 Top Plate 033357-01 Cover Plate (Acrylic) 033358-01 Corner Post 033359-01 End Post 033361-01 Steering PCB Bracket 03336201 Roller Shaft 033363-01 Cylindrical Post 033364-01 Adjustable Post 033365-01 Spacer 033366-01 Trak Bali™ 033367-01 Bearing 034168-01 Label with Lubrication Instructions
030369-01
E] 90p0e!-0!
rs ud
yooso@o ev IRATAO
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 79-58005 CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA conditionally issued, and neither 1 thereot confers or transters any right in, or iicense to use, the subject matter of the draw ing or aay design or technical information shown thereon, nor any ‘right to reproduce this drawing or any part thereot. Except for manufacture by vendors of Alar, Inc., and for manulacture under the corporation's written, license, no fight to reproduce this drawing is granted or the subject matter thereot unless by written agreement This drawing is oni receipt no: possess! °
SG eewIne BD
° Traces shown are ‘on opposite side.
with of written permission from the corporation,
Figure 22 Steering Printed Circuit Board Assembly A009060-02 Cc Parts List
Part No. Description (Reference Designations and Locations in Bold)
10-5331 10-5392 10-5471 27-250104
34-2N3643 79-58005 030369-01 330 Ohm, +5%, %4W Carbon Composition Resistor (R10-13) 3.9K Ohm, +5%, %W Carbon Composition Resistor (R14, 15) 470 Ohm, +5%, %4W Carbon Composition Resistor (R7-8) 0.1 uf, +20%, 25V Ceramic-Disk Radial-Lead Capacitor (C2) 10 uf, + 10%, 20V Tantalum Axial-Lead Capacitor (C1) Type 2N3643 Switching Transistor (Q1, 2) 10-Contact Connector Radial Optical Coupler
46-2038001 46-2022502 A006958-01 Ya 04 tah J =
TOP VIEW
79-4411004 (F1 thru F5) fey \ eg A006886-01 u 46-2013002 _agggo66.01 29.053 \_78-70501SC A007444-01 A007192-01 A006555.01 NOTE: Fuses F1, F2, and F6 are not part of this ————_——\| power supply assembly and must be purchased separately. They have been listed here for your convenience.
BOTTOM VIEW NOTICE TO ALL PERSONS RECEIVING THIS CONFIDENTIAL: Remoduetion forbidden without the specific written permission of At Sunnyvale, GA"THe urawing is only conditional issued, and neither receipt nor possession thereof confers or transfers any right in, of license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part there Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is anted or the subject matter thereof unless by written agreement with or written permission from the corporation.
Figure 23 Type B Power Supply Assembly M A007197-01
Parts List
Part No. Description (Reference Designations in Bold)
A006555-01 Rectifier P.C. Board Assembly
| A006958-01 | Voltage Selection Plug | (95V—Black) |
| A006958-02 | Voltage Selection Plug | (110V—Orange) |
| A006958-03 | Voltage Selection Plug | (205V—Green) |
| A006958-04 | Voltage Selection Plug | (220V—Red) |
A006886-01 Type B Transformer Termination Assembly A007192-01 Power Switch Termination A007444-01 Power-In Harness A009266-01 Power Supply Base Assembly 29-053 26,000 uf 15V Electrolytic Capacitor 41-2003 5-Amp Power Line Filter
| 46-2012502 | 2%2-Amp, 250-Volt Slow-Acting Type 3AG Fuse | _(F3, F4) |
| 46-2013002 | 3-Amp, 250-Volt Slow-Acting Type 3AG Fuse | (F1*, F2*) |
| 46-2022502 | 2¥2-Amp. 250-Volt Slow-Acting Type 3AG Fuse | (F6*). Alternate is part no. 46-2012502. |
| 46-2038001 | 8-Amp, 125-Volt Normal-Acting Type 3AG Fuse | (F5) |
78-70501SC 2" Diameter Capacitor Mounting Bracket 79-4411004 Panel-Mounted Non-Indicating 3AG Cartridge-Type Fuse Post (F1-F5)
- Fuses F1, F2, and F6 are not part of this power supply assembly and must be purchased separately. They have been listed here for your convenience.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproducticn’ forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally’ issued, and. neither receipt nor possession thereot confers or transters any Fight in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any ‘right to reproduce this drawing or any part thereo!. Except for manutacture by vendors of Atar, Inc., and for manufacture under the corporation’s writes license, no right to reproduce this drawing is granted or the subject malter thereof uniess by written agreement with or written permission from the corporation. 99-1007
RR mes NN
75-9448 99-10096
99-10064
COIN INLET CHUTE 99-10097
ia 99-10105 COIN MECHANISM SEE PARTS LIST — (71-42xxxx) {? a7 65-441C getoree if _ 72-9603S COIN RETURN a SWITCH WIRE CHUTE 99-10068 SEE PARTS LIST ISS 99-1087 (99-0075 thru y we. re 31-1N4002 COIN SWITCH ASSY. PART OF 99-10047 SEE PARTS LIST Setoons 99-1082 (99-1042 thru 7514128 99-10045)
Figure 24 New Coin Door 71°41 0xxxx
COIN RETURN BUTTON ASSY.— SEE PARTS LIST (99-1012 thru 99-1002, and 99-10107)
COIN DOOR ONLY— SEE PARTS LIST (@9-10008 and 10010)
99-10094
PART OF 99-1074 fj
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neitner receipt nor possession thereof confers or transfers any rightin, oF license to use,
the subject matter of the drawing os any design of
technical information shown thereon, nor an} Tight to reproduce this drawing ot any part thereo| Except tor manufacture by vendors of Atari, Inc., and for manutacture under the corporation's writ: ten license, no right to reproduce this drawing is granted or the sudject matter thereof unless by Written agreement with of written permission from the corporation. PRICE PLATE— SEE PARTS LIST (99-10070, 99.10083 thru 99-10092, and 99-1008)
75-5520B
75-9158, COIN RETURN BUTTON COVER— SEE PARTS LIST (89-10055 thru 99-10059)
99-10074
99-10062
99-10051
Figure 24 New Coin Door 71-10xxxx T2-JA\4058
99-10054 Missile Comman \a™
ww
72:HA1404C
89-10066 99.10061
an Figure 24 New Coin Door, continued Parts List
Part No. Description
31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-4410 General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism 71-1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 71-1210PE U.K. 10 P coin mechanism 71-1220CA Australian 20¢ coin mechanism 71-1225CU US. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C. #4x%" Slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plated screw 72-JA1405B #4x5/16” Slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40x3/8" Slotted truss-head steel machine screw 72-9603S #6-32x3/16" Slotted truss-head steel machine screw 75-915S #%-20 Standard pattern cadmium-plated steel hex nut 75-9188 #8-32 Standard pattern cadmium-plated steel hex nut 75-9448, #4-40 Polymer self-locking steel hex nut 75-948S #8-32 Polymer self-locking steel hex nut 75-1408S #4-40x¥2" Slotted pan-head steel machine screw 7514128, #4-40x34" Slotted pan-head steel machine screw 75-5520B #%4-20x1%" Round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015 German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Beigian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly 99-10040 Coin inlet chute assembly 99-10041 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (silver wire) 99-10043 Coin switch assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 coins (black wire) 99-10044 Coin switch assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire coins (gold wire)
Figure 24 New Coin Door, continued Parts List
Part No. Description
99-10045 Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10052 Coin return lever 99-10054 Coin button housing 99-10055 Coin return button cover for Japanese Y100 coin 99-10056. Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price plate 99-10084 German 1 DM price plate 99-10085 German 2 DM price plate 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20° price plate 99-10092 Italian 100 Lire price plate 99-10094 Fish paper insulation 99-10095 Toggle switch 99-10096 “U"-type fastener 99-10097 Fish paper insulation 99-10101 Goin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105 Anti-penny-flip bar 99-10107 U.S. 50¢ coin return button assembly 99-10108 U.S. 50¢ price plate—for two quarters
-0. —O3vERSION| (Prov, ~02 oa version (ROM)
SEE DETAIL
IN +SV BUS
BAlo Bus
1) Nm f —5v BUS DETAW TYP. 6 PL, SCALE : NONE OF CONNECTED PADS. mt +12v BUS 2708 ENABLE
Or license to use, the subject matter of tr
In oF technical sho
SPLIT PAD CONNECTIONS AS DETAILED ARE
APPLICABLE TO USE OF @3IGE’S.USE OF 2708'S
REQUIRE BRIDGING OF OPEN PADS AND CUTTING fen
is granted or agreement ion,
D Figure 25 Game PCB Assembly A035467-01 thru -04
Figure 25 Game PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
€012294-01 Audio lf N-Channel MOSILSI Custom Chip (P8/9) 21-101683 .088 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor {C65-68) 24-250105, 1 ut Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C76-79, 98, 100-104) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C20, 23, 39) 24-260107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C9, 10, 46, 57, 91) 24-250226 22 uf Aluminum Electrolytic Fixed Axiai-Lead 25V Capacitor (C90) 27-250103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C76-79) 28-101102, 1000 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C99, 105) 29-088 -1 ui Ceramic-Disc 25V Radial-Lead Capacitor (C1-8, 13-16, 18, 19, 21, 22, 30, 38, 43-45, 47-56, 58-64, 69-75, 80-89, 92-97, 106)
| 31-1N914 | 75V Type-1N914 Switching Diode | (CR2) |
34-2N3643 Type 2N3643 NPN Switching Transistor (Q8) 34-2N6044 Type 2N6044 NPN Darlington Transistor (Q1-3) =——
| 37-4584B | Type 14584 Integrated Circuit | (C9, C11) |
| 37-7400 | Type 7400 Integrated Circuit | (C5, D8) |
| 37-74800 | Type 74S00 Integrated Circuit | (A8) |
| 37-7404 | Type 7404 Integrated Circuit | (E6, K7) |
| 37-74H04 | Type 74H04 Integrated Circuit | (B6) |
| 37-74804 | Type 74804 Integrated Circuit | (D7) |
| 37-7407 | Type 7407 Integrated Circuit | (N11) |
| 37-74LS08 | Type 74LS08 Integrated Circuit | (H7) |
| 37-7408 | Type 7408 Integrated Circuit | (R2, J6) |
| 37-74S08 | Type 74S08 Integrated Circuit | (M3) |
| 37-74LS10 | Type 74LS10 Integrated Circuit | (E3) |
| 37-7410 | Type 7410 Integrated Circuit | (B5) |
| 37-74LS14 | Type 74LS14 integrated Circuit | (D3) |
| 37-7414 | Type 7414 Integrated Circuit | (J9) |
| 37-7427 | Type 7427 Integrated Circuit | (B7) |
| 37-7432 | Type 7432 Integrated Circuit | (C3, R5) |
| 37-74LS32 | Type 74LS32 Integrated Circuit | (J7) |
| 37-74S32 | Type 74S32 Integrated Circuit | (C4, L5, K6) |
| 37-7442 | Type 7442 Integrated Circuit | (N2, E8) |
| 37-7474 | Type 7474 Integrated Circuit | (H6, A7, E7, F7, J8, A9) |
| 37-74S74 | Type 74874 Integrated Circuit | (A6, B8, C8) |
| 37-7475 | Type 7475 Integrated Circuit | (R7) |
| 37-7493 | Type 7493 Integrated Circuit | (D4) |
| 37-74109 | Type 74109 Integrated Circuit | (D6) |
| 37-74125 | Type 74125 Integrated Circuit | (R6) |
| 37-74LS139 | Type 74LS139 Integrated Circuit | (P2, M5) |
| 37-74LS153 | Type 74LS153 Integrated Circuit | (F5, H5, J5, K5, P7) |
| 37-74153 | Type 74153 Integrated Circuit | (F3, H3, J3, K3) |
| 37-74LS157 | Type 74LS157 Integrated Circuit | (H2, J2, K2, L2, M2, M7, D9) |
| 37-74S157 | Type 748157 Integrated Circuit | (E4) |
| 37-74160 | Type 74160 Integrated Circuit | (E5) |
Figure 25 Game PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 37-74163 | Type 74163 Integrated Circuit | (D5) |
| 37-74LS163A, | Type 74LS163A Integrated Circuit | (RA) |
| 37-74LS166 | Type 74LS166 integrated Circuit | (P6) |
| 37-74175 | Type 74175 Integrated Circuit | (L8) |
| 37-74LS175 | Type 74LS175 Integrated Circuit | (C7) |
| 37-74LS191 | Type 74LS191 Integrated Circuit | (K8, K9) |
| 37-74191 | Type 74191 Integrated Circuit | (A4, B4) |
| 37-74LS195 | Type 74LS195 Integrated Circuit | (M6, N7) |
| 37-74LS244 | Type 74LS244 Integrated Circuit | (A/B1, E2, F2, P5, L9, M9, P10, B/C1, N/P3) |
| 37-74LS251 | Type 74LS251 Integrated Circuit | (N5) |
| 37-74S260 | Type 74S260 Integrated Circuit | (A5) |
| 37-74LS273 | Type 74LS273 Integrated Circuit | (N6, F9) |
| 37-LM324 | Type LM324 Integrated Circuit | (N10) |
38-MV5053 Type MV5053 Light-Emitting Diode (CR1)
| 62-001 | SPST Pushbutton Switch | (B3) |
66-118P1T 8-Station Single-Throw, Dual-Inline-Package Bit Switch (R8, R10) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (For -01 and -03 PCB Assemblies: D1, E1, F1, H1, J/K1, K/L1, L/M1, M/N1, N/P1, R1, R3; For -02 and -04 PCB Assemblies: H1, JIK1, K/L1, M1, N/P1, R1) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C2, P8/9) 81-4302 Nylon Snap-In Fastener
| 90-123 | 10.000 MHz, + .005%, Crystal | (Y1) |
90-6013 Microprocessor (C2)
| 90-7005 | Random-Access Memory | (L7) |
020670-01 Test Point
| 035826-01 | Programmable Read-Only Memory | (L6) |
| 100017-001 | Random-Access Memory | (F4, H4, J4, K4, L4, M4, N4, P4) |
| 110000-102 | 1K Ohm, +5%, %4W Resistor | (R1, 2, 4, 13, 16, 21-26, 39, 60, 61, 73, 74, 85, 95, 109-122) |
110000-103 10K Ohm, +5%, %4W Resistor (R3, 17-20, 30-38, 66-71, 83, 84, 86-88, 93, 94, 96-100) 110000-152 1.5K Ohm, +5%, %W Resistor (R79)
| 110000-220 | 22 Ohm, +5%, %W Resistor | (R46, 47, 82) |
110000-221 220 Ohm, +5%, V4W Resistor (R72) 110000-222 2.2K Ohm, +5%, YW Resistor (R76)
| 110000-332 | 3.3K Ohm, +5%, %4W Resistor | (R56-59, 89-92) |
| 110000-270 | 27 Ohm, +5%, %W Resistor | (R5-12, 27-29) |
110000-331 330 Ohm, +5%, %W Resistor (R14, 15, 78)
| 110000-391 | 390 Ohm, +5%, %W Resistor | (R45, 81) |
| 110000-471 | 470 Ohm, +5%, ¥4W Resistor | (R40-44, 48-55, 80) |
110000-472 4.7K Ohm, +5%, 14W Resistor (R75)
| 110000-682 | 6.8K Ohm, +5%, YW Resistor | (R101-108) |
| 110000-822 | 8.2K Ohm, +5%, %4W Resistor | (R77) |
122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C24-29, 31-37, 40-42)
| 137002-001 | Type 74886 Integrated Circuit | (L3) |
137149-001 Type 74LS11 Integrated Circuit (F6, N3)
For remaining memory components and their part numbers, see list on next page.
-01 P.C. Boards Figure 25 Game PCB Assembly Parts List
Memory Components and Their Equivalents {Locations Shown in Bold)
-02 P.C. Boards -03 P.C. Boards -04 P.C. Boards {mostly PROMs) (ROMs) (mostly PROMs) (ROMs)
03581201 KIL1 03681202 KIL1 03562201 KIL1 03582202 K/L1 03581301 F4 03581302 F1
03582301 LMM 03982301 L/M1 03582302 UNM4 03582302 LIM1
03581601 NIP1 035816-02 NIP1 03582401 NIP1 03582402 NIP1 035817-01 MIN4 035817-02 MIN1
03581801 R1 03581802 Ri 03582501 R1 03582502 AI 036819-01 R3 03581902 R3
03680801 Hi 03580802 H1 03582001 -H1 03582002 H1 03580901 D1 03680002 01
035810-01 J/K1 035810-02 J/K1 035821-01 J/K1 03582102 J/K1 035811-01 Et 035811-02 Et
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL: Reproduction forbidden without the
ific written permission of At Sunnyvale, CA.
drawing is only conditionally’ issued, and neither
lor possession thereof confers or transfers any
use, the subject matter of the draw-
A shown thereon, TRACES SHOWN ARE ON OPPOSITE SIDE
Figure 26 Regulator/Audio Il PCB Assembly A035435-03
Figure 26 Regulator/Audio || PCB Assembly Parts List “Oy
Part No. Description (Reference Designations and Locations in Bold)
12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5} 19-100P1015 -1 Ohm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108 1000 uf Aiuminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31) 24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 27-250102 .001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C2, 7, 16) 27-250103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, 6, 14, 15) 29.088 .1 uf Tantalum 25V Capacitor (C3, 11, 20, 21) 31-A14F 50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)
| 33-TIP32 | PNP Power Transistor, Type TIP32 | (Q2) |
| 34-2N3055 | NPN Silicon Transistor, Type 2N3055 | (Q3) |
| 37-LM305, | 5V Linear Voltage Regulator | (Q1) |
| 37-7812 | + 12V Voltage Regulator, Type 7812 | (Q8) |
| 37-7905 | —5V Voltage Regulator, Type 7905 | {Q9) |
52-004 Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper Wire with 3" Centers 72-1608C #6-32 x Y2" Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x %4" Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | (Q3) |
78-16014 Thermally Conductive Compound (Q2, 5, 7-9)
| 79-58306 | 6-Position Connector Receptacle | (J6, J9) |
| 79-58308 | 9-Position Connector Receptacle | (J7) |
| 79-58346 | 12-Position Connector Receptacle | (J10) |
| 79-58354 | 4-Position Connector Receptacle | (J8) |
020670-01 Test Point 034531-01 Heat Sink
| 110000-010 | 1Ohm, + 5%, %W Resistor | (R10, 19) |
| 110000-100 | 10 Ohm, + 5%, “%4W Resistor | (R11, 20, 29, 30) |
110000-101 100 Ohm, + 5%, YW Resistor (R4, 12, 22)
| 110000-102 | 1K Ohm, + 5%, Y4W Resistor | (R27, 28) |
110000-103 10K Ohm, + 5%, %4W Resistor (R13, 14) 110000-271 270 Ohm, + 5%, %W Resistor (R1) 110000-330 33 Ohm, + 5%, YW Resistor (R3) 110000-392 3.9K Ohm, + 5%, 14W Resistor (R6) 110000-562 5.6K Ohm, + 5%, %4W Resistor (R32, 33) 110000-752 7.5K Ohm, + 5%, %4W Resistor (R7) 110001-221 220 Ohm, + 5%, VeW Resistor (R9, 21)
| 116001-150 | 15 Ohm, + 5%, 5W Resistor | (R31) |
122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C6, 8, 15, 17) 137151-002 Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7)
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
a 3rd printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
lf you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm C Distributor
Address C Operator
City _. State Zip CO Other.
First fold
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if maited in the United States
Cut along this line aS
Second fold
eBpe siyj ede, O14
Warranty
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantabil-. ‘ity and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products uhder this order.
AES ERS ERS SS LAS A AI The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. =
< = =
Atari distributors are independent, being privately owned and operated. In their judgment they may. sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible forthe quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This. document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for a any other purpose whatever, and remains the property of Atari, Inc. Neither it nor the information it contains may be reproduced, used, or disclosed to persons not haying a need to know consistent with the purpose of the loan, without written consent of Atari, Inc:
ATARI" ATARI ING 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 ¢ TELEX 35-7488