CATHODE RAY TOMES

Race Drivin' Compact TM-360 1st Printing

Race Drivin' Compact (Atari Games, 1989) · Technical Manual · 88 pages · 117 sections · original scan

Page 1

TM-360. ist printing

> > a GAMES

\_ FURR ORC TARP Tene] BEE PR

Page 2

e 4 yKfice guroPe land \ amited set vw

Page 3

Patents are pending on several parts of the Race Drivin’ Compact simulator.

Page 4

Copyright © 1989, 1990 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing wansaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by 1s. Anyone who purchases such copies risks forfeiting ~-=such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95036

Printed in the U.S.A 11/90

Produced by the Atari Games Technical Publications Department. Technical Writing and Editing: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner

Notice Regarding Non-Atari* Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts mot supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram. ¢ The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Contents

1 Set Up How to Use This Manual . Operating the Simulator Inspecting the Simulator. Adjusting the Glides .. Control and Switch Locations Setting the Coin and Game Optior Simulator Systems Simulator Driving 1-1 1-2 1-2 1-2 1-2

1-3 2 Self-Test and Diagnostics Entering and Exiting the Self-Test Automated Self Test....... Program ROM and RAM Tes! Microprocessor and Board Tests. Test Menu Screens Operator Screens... Coin Options... Game Difficulty. Game Optio: Statistics ..

Games Played by Day and Hour Set Controls Screens Control Inputs Screen .. Monitor Test Patterns ... Set Clock Screen Disable Broken Controls Screen . Special Functions Screen. Multisync Board GSP Tests. Multisync Board Controls. Steering Wheel Submenu . Link Connector Test... Multisync Board ROM Checksums. Multisyne Board ZRAM Test. ADSP Board Tests Sound Board .... DSK Board Tests .. LEDs on the Multisync PCB . DIP Switches ..

3 Maintenance and Troubleshooting Maintaining and Inspecting Coin Mechanism... Maintaining the Coin Mechanism Dashboard... Removing the Dashboard Installing the Dashboard Interior Components... Cleaning the Interior Components Key Switch Assembly... Oiling the Key Switch Assembly, Replacing the Spring in the Key Switch Assembly. Tightening the Screw in the Key Switch Assembly Replacing the Swit

If the Gas or Clutch Pedal Does Not Wc If the Brake Pedal Does Not Work Greasing and Checking the Pedals Replacing a Pedal . Replacing a Spring Replacing the Clute! Potentiometers Testing the Brake Pedal Strain Gauge and Bonding...... Replacing the Brake Strain Gauge Shifter Assembly. Lubricating the Shifte: Replacing a Shifter Swit Speakers ... Removing a Speaker Static-Sensitive Devices Replacing Static-Sensitive Devices Steering Assembly .... Oiling the Bronze Bearin; Adjusting the Steering Bel Replacing the Steering Belt Replacing the Steering Motor. Replacing the Encoder or Centering PCB. Replacing the Centering Disk..... Replacing the Encoder Disk Video Display ..... Adjusting the Video Display Removing the Video Display Replacing the Video Display . 4 Illustrated Parts Lists See the list of Illustrations that follows.

Statistics Sheet

iti

Page 6

: Figure 2-1 Figure 2-2

Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11

Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Illustrations

Program ROM and RAM Test Screen.. 2-3 Microprocessor and Board Tests Screen. Instructions for Test Menu Screen Test Menu Screen Coin Options Screen Game Difficulty Scree: Custom Game Options Screet Game Options Screen .... Statistics Screen. Histogram Screen.. Games Played by Day and Hour Screen First Set Controls Screen . Control Inputs Screen Set Clock Screen...... Disable Broken Controls Screen . 2-3

Figure 2-16 Figure 2-17 Figure 2-18 Figure 2-19 Figure 2-20 Figure 2-21 Figure 2-22 Figure 2-23 Figure 2-24 Figure 2-25

Figure 2-26

iv Special Functions Screen. GSP Tests Screen... Multisyne Board Controls Screen Pots: 8-Bit Screen .... Steering Wheel Submenu Screen. Send Force Screen....... Link Connector Test Screen ROM Checksums Screen ADSP Board Tests Scree ADSP ROM Checksums Tests SCLEEN ..-sseseeesreereee Sound Board Tests Screen. Figure 2-27

Figure 2-28 Figure 2-29

Figure 3-1

Figure 3-2

Figure 3-3

Figure 3-4 Figure 3-5

Figure 3-6

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8

Figure 4-9 Figure 4-10

Figure 4-11 Figure 4-12 Figure 4-13 Figure 4-14 Sound Board Sound Wave ROM Checksums Screen DSK Board Test Screen .... DIP Switch and LED Locations on the Multisync PCB

Gas or Clutch Pedal is Not Working or Is Working Erratically and You Have Tried the Set Controls Screens.. Brake Pedal is Not Working or Working Erratically and You Have Tried the Set Controls Screens........... The Steering Wheel Continuously Turns in One Direction and You Have Tried the Set Controls Screen: sssserneee O15, Installing the Steering Pivot Shaft..... 3-16 The Steering Wheel is Jerky and You Have Tried the Set Controls Screens .. The Steering Wheel Has No Feedback and You Have Tried the Set Controls Screens 3-8

3-10

Cabinet-Mounted Assemblie: Dashboard Assembly. Steering Assembly... Shifter Assembly ..... Key Switch Assembly Brake and Gas Pedal Assembly Clutch Pedal Assembly...... Coin Acceptors, Inc. Coin Door Assembly........ Power Supply Assembly. Hard Drivin’ Compact Multisync PCB Assembly. APU PCB Assembly Motor Amplifier PCB Assembly Encoder Disk PCB Assembly. Centering Disk PCB Assembly

  • 4-2
Page 7

Table 1-1

Table 2-1

Table 2-2 Table 2-3

Table 2-4 Table 2-5

Table 2-6 Table 2-7

Table 3-1 Table 3-2 Tables

Simulator Specifications.

Using the Self-Test Screens and Diagnostics... Coin Option Settings . Summary of All Screens Appearing in the Self-Test... Game Option Settings When to Use the Special Function Ttems..... LED Status Using the DIP Switches .

Maintenance and Inspection Items...... 3-2 Voltage Inputs and Test Points on the Simulator PCBs... Table 3-3 Table 3-4 Table 3-5

Table 3-6 Table 3-7

Table 3-8 Table 3-9

Table 3-10 Table 3-11

Table 3-12

Table 3-13 Troubleshooting All Controls .. Troubleshooting the Key Switch Troubleshooting the Clutch or Gas Pedal ..... Troubleshooting the Brake Pedal Pedal Potentiometers Harness Connections ..... Troubleshooting the Shifter. Hamess Connections to the Shifter Switches... Troubleshooting the Speakers. Troubleshooting the Steering

Torque Table for the Screws on the Steering Assembly..... Troubleshooting the Video Display...

Page 8

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or

vi modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.
Page 9

CHAPTER 1

Set-Up

How To UsE THIs MANUAL

This manual is written for operators and service personnel. It provides information for setting up, driving, test- 4 ing, and maintaining your Race Drivin’ Compact™ simulator. The manual is divided into the following chapters:

¢ Chapter 1 contains set-up and simulator driving information.

¢ Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the Race Drivin’ compact simulator. You can troubleshoot the PC boards, main circuits, and controls using the more than 60 screens in the self-test. You should regularly test the boards and controls with the self-test to keep your simulator in peak condition and at top earnings. ¢ Chapter 3 contains the preventive maintenance schedule for the simulator and the repair procedures, flowcharts, and troubleshooting tables for each control. If you have problems with your simulator, use this chapter to troubleshoot and to repair it. Be sure to perform the preventive maintenance tasks to keep your simulator in good condition.

  • Chapter 4 contains the illustrated parts lists.
Page 10

Set-Up

Operating the Simulator

To operate your simulator for maximum income, make sure your players know that the simulator is designed to be driven like a real car. You should regularly do the automated self-test and check the controls with the Control Inputs screen in the self-test. By using the selftest regularly, you can find and fix problems immediately. This lets you keep your simulator in top condition,

NOTE If you are installing a new PC board or a control in your simulator, go through the Set Controls screen in the self-test. This is explained in Chapter 2. /f you turn on your simulator and you see a screen that says Initialize Pot Inputs instead of the attraction screens, then reset the controls by following the instructions on the screens that appear.

Inspecting the Simulator

WARNING To avoid electrically shocking yourself and damaging the simulator electronics, do not plug in the simulator until it has been inspected and set up for your line voltage.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded. Inspect your Race Drivin’ simulator carefully to ensure that the simulator is complete and was delivered to you in good condition.

Inspect the cabinet as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Open the service door. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a, Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets.

1-2 Table 1-1 Simulator Specifications oe g

c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. e. Inspect other sub-assemblies, such as the video display, controls, printed-circuit boards (PCBs), and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Adjusting the Glides

After you move the simulator into location, screw out the adjustable glides in the base to support it. Before you move the simulator, retract the glides so they are not damaged.

Control and Switch

Locations

Most of the controls are located inside the seat, behind the coin door. The only exception is the power on/off switch.

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet.

Volume Control The volume control is located behind the upper coin door under the seat.

Self-Test Switch The self-test switch is located behind the upper coin door under the seat. See Chapter 2 for a complete description of the self-test.

Page 11

Auxiliary Coin Switches An auxiliary coin switch is located on the component bracket behind the upper coin door under the seat. Use the auxiliary coin switch to give players coin credits.

Coin Counter The coin counter is located behind the upper coin door. The coin counter records the number of coins deposited. It does not count the credits given by the auxiliary coin switch.

Setting the Coin and.

Setting the Coin and Game Options

The Race Drivin’ Compact coin and game options are set in the self-test. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Simulator Systems

The Race Drivin’ simulator uses eight PCBs to give a realistic look and feel to the driving. These PCBs are the DSK PCB, the Multisync (main) PCB, the ADSP PCB, the motor amplifier PCB, the audio and power PCB (mounted on the power supply assembly), two PCBs mounted on the steering wheel, the sound PCB, and the video display board. These PCBs control the simulator software, the video display, and the controls. The Multisyne PCB, which is the largest, holds the 68010 and the GSP microprocessor systems. The 68010 system contains program RAM and ROM. The GSP (Graphic Systems Processor) microprocessor system controls the video RAMs (VRAMs). The ADSP board and the sound board are mounted with the multisync main PCB. The motor amplifier PCB is mounted in a heat sink assembly located on the driver's left. It controls the steering wheel motor using the input from the two boards mounted on the steering assembly. Set-Up

Simulator Driving

This section describes the features and driving of the Race Drivin’ simulator. Introduction

Race Drivin’ includes all of the innovative game features that made Hard Drivin’ the industry’s first true driving simulation game, plus many more new features.

New Features Improved Handling — Faster microprocessor and more efficient software code provides a now imperceptible lag time between control input and screen graphic response. Race Drivin’ feels even more like a real car! New Tracks — The Super Stunt track will challenge even the best Hard Drivin’ stunt racers. New tests of skill include a corkscrew loop, a jump loop, and a winding mountain road. The autocross track with a built-in pace car provides feedback to hone competitive driving skills. The vector-drawn pace car is actually a recorded view of the player's best lap. Buddy Race — Two-player sequential race in which the computer records the performance of player one, and player two races head-to-head against the first player and the clock. Linked Race — Install a simple cable between two Race Drivin’ Compact simulator cabinets, adjust game options, and the buddy race becomes a true head-to-head competition. Select a Car — Players can select from several different sports cars to suit the race track chosen. The Race Drivin’ cars are modeled after the performance features of several well-known sports cars. Each car has its own handling characteristics of off-the-line quickness, top speed, and cornering. In addition to all of the innovations aimed at the player, Atari has also included many improvements that will be appreciated by the operator.

Page 12

Set-Up

1-4 S

Page 13

CHAPTER 2

Self-Test

The Race Drivin’

simulator is a com-

plex machine. To keep it at peak efficiency and maximum earnings, you should regularly check the controls, RAMs, ROMs, PCBs, and microprocessor systems. You can check

all of these when you switch on the self-test. Also

in the self-test you can check the video display, 1} the statistics, and sei

the internal clock.

If you cannot use the self-test

because the screen is dark, you can use a DIP switch on the main PCB to find the source of the

problem. If you are having electronic problems, you can check the state of various signals with the LEDs on the main PCB.

Page 14

Self-Test

You should regularly check the following screens and information. We recommend you check these when you first set up the simulator, each time you collect money, or when the simulator is not working correctly.

  • Use the automated self-test, which begins automatically when you turn on the self-test to test the program RAMs and ROMs, the video RAMs, color RAMs, the DSK PCB, the ADSP PCB, and the sound PCB. The test takes about five minutes to run.
  • Check the Control Inputs screen, which you choose from the Test Menu screen. This shows the voltage input to the Multisync PCB from the steering wheel, brake pedal, gas pedal, clutch pedal, seat, and shifter. With this information you can easily check how the controls are working.
NOTE If the control inputs are wrong, your earnings may drop, since the realistic driving feel is lost.
  • Check the Statistics, Histogram, and Games Played by Day and Hour screens which show the statistical information about how and when your simulator is played. Table 2-1 shows you what tests and screens to use at different times and for different problems.

Table 2-1 Using the Self-Test Screens and Diagnostics

Automated Self-Test

Page 15

Entering and Exiting the Self-Test

You enter and exit the automated self-test procedure by turning the self-test switch on or off. The switch is located at the back of the upper coin compartment. You run the tests with the door open so that you can press the right and left coin switches to move up and down the menus. The self-test consists of:

  • A five-minute automated self-test of the ROM, RAM, the microprocessor, and the PC boards « A Test menu from which you can run specific tests in the event that you receive error messages Self-Test

The automated testing takes about five minutes. The results appear on the screen. Messages in red alert you to a problem. You can run further testing from the Test menu. If you do not want to wait for the systems and PCBs to be tested, you can skip these tests by turning the ignition key while in the program ROM and RAM screen, Figure 2-1. If the self-test proceeds beyond this screen, it will run its course.) If you want to exit to the attract mode, just turn the self-test switch off.

Figure 2-1 Program ROM and RAM Test Screen

If you are running a specific test and turn off the selftest switch to exit, you may need to proceed through all the screens in the submenu and return to the Test menu before you return to the attract mode.

Automated Self-Test

When you enter the self-test, the simulator automatically tests the program ROM and RAM, the video RAM, the color RAM, the DSK PCB, the ADSP PCB, and the sound PCB,

NOTE If you do not see anything on the video display screen, you may have a video display problem or a simulator system problem. See DIP Switches at the end of this chapter to diagnose the problem. Figure 2-2 Microprocessor and Board Tests Screen

Program ROM and

RAM Test

When you enter self-test, the simulator tests the program ROM and RAM. The screen in Figure 2-1 shows the results of a program ROM and RAM test. The top of the screen shows the ROM test result. The numbers on the left and the letters on the top of the screen show the locations of the ROMs on the Multisyne PCB. If a white box appears, then the ROM there is good. If an empty box appears (as shown at 200U and 210U), then the ROM there is bad. If nothing appears, then nothing was tested there. The RAMs are tested after the ROMs. If the RAMs have no errors, then you see the message Program RAM OK. If the test finds an error, then you see Bad Program RAM At with the bad RAM location listed. This screen disappears after a few seconds and the self-test continues. However, the screen with the results of the complete self-test, shown in Figure 2-2, shows the message Bad Program ROM (or Bad Pro- Sram RAM) if it found an error in the program ROMs or RAMs.

Page 16

Self-Test

Microprocessor and

Board Tests

After checking the program RAM and ROM, the automated self-test checks the simulator's microprocessor and PC boards, It tests the video RAM and color RAM in the GSP microprocessor system, the DSK board, the ADSP board, and the sound board. The test takes four to five minutes. You see the screen in Figure 2-2 when the test finishes. if the system or board is good, OK follows the test name. If it is bad, the word Bad precedes the name of the board or system (except for the ADSP board test, which gives more information). If you have a bad system or board, then choose Special Functions from the Test menu, choose the appropriate system or board tests from the Special Functions menu, and read the description of the tests in this chapter. Here is a brief description of each microprocessor and board test performed during the automated self-test. PROGRAM ROM: Described above. PROGRAM RAM: Described above. GSP VRAM: Uses the Simple GSP VRAM Test. (Described in the section Multisync Board GSP Tests.) GSP COLOR RAM: Uses the GSP Color RAM Test. (Described in the section Multisync Board GSP Tests.) DSK Board: Tests two ASIC systems, the DSK Program RAM, the DSK ZeroPower RAM, and the DSK Program ROM. These tests are described in the section DSK Board Tests. ADSP Board: Tests the ADSP board memory and the ADSP-2100. Most of the error messages are self-explanatory. (Does Not Respond generally indicates a missing board.) Sound Board: Tests the sound program ROM and RAM, the sound board communications ROM and the 32010 ROM. Sound Wave ROMS: Tests the ROMs that have the sound waveform data. If any are bad, the message Bad Sound Wave ROMs appears on the screen. Steering Wheel Motor Test: Performs a simple test of the steering wheel system.

Test Menu Screens

After the microprocessor and board test is finished or you bypass it, turn the key to proceed to the Test menu. The Test menu screens let you conduct specific troubleshooting in the event of problems. Turn the key once to see a screen that explains how to select from the Test menu, shown in Figure 2-3. Turn the key again to see the Test menu, shown in Figure 2-4, As the screen shown in Figure 2-3 explains, you use the right and left coin switches and the ignition key to make a selection from the Test menu. Pressing the sight or left coin switch on the back of the upper coin door moves you up or down the menu. When the op-

Figure 2-5 Coin Options Screen

Page 17

Self-Test

Table 2-2 Coin Option Settings

2 coins/1 credi ‘coins/1

tion you want is white, curn the ignition key to select it. The submenus for the specific tests work the same way. The Test menu, shown in Figure 2-4, is the most important screen in the self-test. Use this screen to choose specific tests to pinpoint problems and to set the game options. Table 2-4 shows all the tests that are available from the Test menu.

Operator Screens

Choose Operator Screens from the menu by pressing the right or left coin switch until this item is white, then turn the ignition key to select it. If you are in the operator screens and want to go to the attract mode, first turn the key to go through the remaining operator screens. When you return to the Test menu, turn off the self-test switch. The Operator Screens let you set game options and monitor the use of the simulator. The choices on the Operator Screens submenu are:

Coin Options

Link Options Game Options Statistics Histograms of Game Times Error Count Games Played by Day and Hour eee rece Figure 2-6 Game Difficulty

The first operator screen, Coin Options, lets you reset the coin credits (see Figure 2-5). To reset the coin options:

  • Move up or down the list by pressing the right or left coin switch. A blue box indicates which item is selected.
  • Press the Abort button and either coin switch to scroll through the settings until you see the one you want.
  • To return to the original settings, press the Abort button and turn the ignition key.
  • When through, turn the key to exit the screen. The default setting of each option is green. The available settings are listed in Table 2-2. The Coin Options are as follows:
  • Coin Mode is the number of coins required for one credit.

Figure 2-7 Custom Game Options Screen

Page 18

Self-Test Race Drivin’ Compact

Histograms _-Extor Coun

eat movement limits. it n the force on th

Full Screen White

‘ull Screen Red ‘ull Scree

2-6

Page 19

Race Drivin’ Compact Self-Test

Table 2-3 All Screens Appearing in the Self-Test, Continued

2-7

Page 20

Self-Test

° Right Mech Multiplier is the number of coins each coin counts as in the right coin mechanism. © Left Mech Multiplier is the number of coins each coin counts as in the left coin mechanism.

  • Bonus Adder lets you choose bonus coins, no bonus, or free play.

Game Difficulty

The game difficulty of each track and the difficulty of the drone car for each track can be set with this screen (Figure 2-6). In addition to settings of easy, medium, hard and very hard, custom tuning is provided. In the Custom setting, you can choose the actual amount of time a driver is given. You can select different times for each individual lap in this option. The actual times for easy, medium, hard, and very hard game difficulty settings are also shown in the custom settings. For example, if you have chosen the medium setting in Game Difficulty, then the custom screen appears as shown in Figure 2-7.

NOTE Always use the preset Game Difficulty settings before you use the settings of the Custom game options.

To move and choose in this screen, do the following:

  • To move up or down the list, press the right or left coin switch.
  • To change a setting, press the abort button and either coin switch.

2-8 Figure 2-8 Game Options Screen

¢ To retum to the setting that was originally on the screen, press the abort button and turn the key.

  • To exit the screen, turn the key. You can change an option when it is inside the blue box. The default setting of each option is green. The other settings are blue when the option is selected. (The other settings are white when the option is not selected.) The custom game options are explained below. © Initial Time is the amount of time always given for one driving session.
  • First Extended Time is the amount of time given if the driver crosses the finish line before the initial time is up. © Second Extended Time is the amount of time given if the driver crosses the finish line before the time is up on his second lap. © Extended Time After Second is the amount of time given when the driver crosses the finish line before the time is up after the first two laps.

Game Options

Use the Game Options screen to set the game difficulty and the operator options as explained below. The screen is shown in Figure 2-8. You operate this screen the same as Coin Options. Press the coin switch to select an option, and press Abort and a coin switch to scroll to the setting you want. Turn the key to save the settings and exit. A list of the available settings is shown in Table 2-4. The Game Options available on this screen set the following:

  • Game Difficulty sets the game difficulty for the drivers. The settings are shown in Table 2-4. The custom setting lets you choose the actual amount
Page 21

of time the players receive. We suggest you use the preset factory setting (easy, medium, hard, and very hard), not the custom setting.

  • Champ Lap Qualification sets the difficulty of qualifying for the championship lap. ° Steering During Altract Mode allows you turn the movement of the steering wheel on or off while the simulator is in the attract mode.
  • Steering Wheel Force is the amount of force exerted by the steering assembly motor on the steering wheel. ° High Score Name Censor controls a program to censor names entered on the high score table. The program deletes letters in possibly objectionable words in the high score table. ° Clear High Score Table clears the high score table at the time chosen, You can choose not to clear the table, clear it now, clear every week, or clear every two weeks. If you choose clear every week or clear every two weeks, the table is cleared when the simulator is turned on after Wednesday midnight every week or every second week. Be sure your simulator clock is set correctly so the table clears at the right time. ° Signs and Gauges allows you to choose whether the signs and gauges are displayed in kilometers or miles.

Statistics

The statistics screen is shown in Figure 2-9. The statistics are collected from the last time the statistics screen was cleared. Write this information on the statistics sheet in the back of this manual to help you maximize your profit. To move to the next screen, just turn the key. To clear the statistics, press and hold the abort button and turn the key at the same time. The statistics the simulator collects are explained below. ¢ Left Coins shows the number of coins counted in the left coin mechanism. ° Right Coins shows the number of coins counted in the right coin mechanism. ° Aux Coins shows the number of times the auxiliary coin switch (inside the coin door) is pressed. Idle Mins shows the number of minutes the simulator has been idle.

  • Active Mins shows the number of minutes the simulator has been played.
  • Error Count shows the number of errors counted in the erasable memory. If you have more than 75, check Self-Test

Figure 2-9 Statistics Screen

the ZRAMs with the self-test. Your simulator may need service. ¢ Total Games shows the number of unique games played.

Bottom Half of Screen For the remaining statistics (except for the five entries at the very bottom of the screen), the three numbers after each entry represent, from left to right: first — original track at the beginning, second — autocross track, and third — super stunt track. © Laps hy Track is numbers of laps, completed or not, on each track. ° No X Games by Track is the number of times the drivers did not get extended games on either track. If the numbers are very high, then the game difficulty may be too hard.

  • 1, 2, and 3+ X Play Games by Track is the number of additional laps given to drivers if they complete the track before the time allotted. These additional laps do not need to be completed to be counted. © Champ Laps is the number of times drivers qualified to race a championship lap. « 2 Player Games by Track is the number of games played with two players, ° 2Player Time by Trackis the average time of all games played with two players.
  • Free Games by Track is the number of free games played on each track.
  • Total Games by Track shows the number of unique games for each track, regardless of how many additional laps each driver received.
Page 22

Self-Test

+ Total Time by Track shows the total time of all games for each track. © Avg Time by Track (sec) shows the average total time of all games for each track.

  • Games by Car shows the number of games played with each type of car. © Inst Rpls is the total number of instant replays.
  • Rpl Abortis the times the drivers pressed the abort button to cut the instant replay short. © Rpl Secsis the total seconds the sirnulator is in the replay mode.
  • Total Credits is calculated by multiplying the coins by the credit setting you chose in Coin Mode. « Avg Time Per Credit is the average amount of time in seconds that each credit gave.

:

Histogram

The histogram screen shows the length of driving time in seconds and the how many times the simulator was driven. The screen is shown in Figure 2-10. Write these numbers on the statistics sheet in the back of this manual to help you maximize your profit. To move to the next screen, turn the key. To clear the histograms, press and hold the abort button and turn the key at the same time.

Error Count

This screen shows the error count on the PC boards. If you call Atari Game Customer Service, the numbers on this screen may help Customer Service personnel troubleshoot your problem.

Games Played By Day and

Hour

This screen, illustrated in Figure 2-11, shows the number of games played every hour in each day. The information on this screen relies on the simulator clock being set correctly. (The clock time is shown on the bottom of the Test menu screen. If the time is incorrect, follow the instructions in the Set Clock section of this chapter to set the clock.) Write the simulator driving information on the statistics sheet in the back of this manual to help you maximize your profit. To clear the screen, press and hold the abort button and turn the key at the same time.

2-10 Figure 2-10 Histogram Screen

Set Controls Screens

If you have problems with the brake, clutch, gas pedal or steering assembly use the Set Controls screens before doing any troubleshooting or repairs. These screens allow you to set the beginning and ending points of the control input to the Multisync PCB. Often, resetting these points solves the problem you have. If resetting does not solve the problem, then check the Control Inputs screen, described below.

NOTE The simulator must be on for at least 15 minutes before you use the Set Controls screen. If you do not wait this long, the brake may not initialize correctly.

If you repair a control, install a new board, or install a new control, go through the Set Conirol screens. The first screen of the Set Controls screens is shown in Figure 2-12.

NOTE If you take a control out of the simulator for or repair it, go through all the Set Controls screens after you replace it. If you do not, the simulator will not operate correctly.

After you choose Set Controls, simply do what the screens say. You must reset ali the controls after you start the screens. The first screen initializes all potentiometers in the simulator. The next screens initializes the limits for the steering assembly, and the gas, clutch, and brake pedals. The numbers on each screen are for factory use.

Page 23

Figure 2-11 Games Played by Day and Hour Screen

NOTE When you initialize the brake, the instructions say to “step firmly” on the brake. Do not stomp on the brake or gently press it. Either way sets the brake limits incorrectly, and drivers will be frustrated when they use the brake,

Control Inputs Screen

Check this screen as part of your regular maintenance to be sure your controls are operating correctly. The Control Inputs screen is shown in Figure 2-13. Self-Test

If you have a problem with a control, first go through the Set Controls screens then check the results on this screen. If using the Set Controls screens does not solve the problem, check Chapter 3 for troubleshooting and repair information about the control. The following controls are checked on this screen. ® The gas pedal and the clutch pedal lines show the voltage input from the pedal potentiometers to the A/D converter circuits on the Multisyne PC board. As you use a pedal, the line length on the screen changes, showing the change in the voltage input from the potentiometer. e The brake force line measures the force with which you press the brake, not the distance it moves. As you press harder on the brake, the line becomes shorter, showing the change in the voltage input from the strain gauge on the pedal. To get correct results for the brake force, the simulator must be on for at least 10 minutes. When the line is shortest, the input is 0 Volts. When it is longest, the input is 5 Volts. If the line length for the gas, brake, or clutch does not change, you have a problem with pedal. See Chapter 3. e The /eft and right coin mechanisms, the auxiliary coin switch, and the abort switch are at the bottom of the screen. As you use the switches, the name of the part should change from blue to green. If it does not, check the switch, mechanism, and harness, e The shifter checks the switch at each gear position. Move the shifter into each gear, and the shifter position number should change from blue to green. If it does not, see Chapter 3 for troubleshooting and maintenance information. « As you turn the steering wheel clockwise, the hexadecimal number should increase and change to

Figure 2-12 First Set Controls Screen Figure 2-13 Control Inputs Screen

2-11

Page 24

Self-Test

zero once every turn. As you tum the wheel counterclockwise, the number should decrease. Every time the steering wheel passes the center position, the words center edge should change from blue to green. If the steering wheel numbers do not change or the words center edge never change to green, see the table Troubleshooting the Steering Assembly in Chapter 3 for more information.

Monitor Test

Patterns

Use this item to see the fourteen screens fer checking the video display, the color RAMs, the GSP, which controls the video RAMs (VRAMs), and the video output. To move through the screens, press the coin switches.

  • Color Bars screen shows these colors from left to right: white, yellow, light blue, green, purple, red, blue, and grey. If the colors are incorrect, see your video display manual for adjustment procedures. ¢ Monitor Adjust is used to set up the monitor.
  • Monitor Brightness checks the adjustment of the video display brightness. ° Grey Scale screen shows a white line on the left, and a grey scale showing black on the left.
  • B/W Dols screen can be used to check convergence and focus. ° B/W Grid screen, shows a black background and a white grid pattern to check convergence. The grid lines should be straight within 3.0 mm. If you need to adjust the convergence, see the video display manual included with the simulator.
  • Diagonal Lines screen can be used to check video display linearity. + Full Screen colors test the color purity of the color RAMs and the display. The test displays a grey, white, red, green, and then blue screen. Each screen should be a rectangle of color, with no curving at the corners and no lines in the raster. If it does not, see your video display manual included with the simulator for adjustment procedures.
  • Monitor High Voltage Test screens switch between a white screen and a grey screen. If the high voltage to the display is regulated properly, the sides of the screen will fluctuate about 3/4 inch from the white to the grey screen. ¢ Scrolling Test screen checks the scroJling mechanism in the GSP.

Set Clock Screen

Choose this item if you want to set the clock, turn the clock on, or turn it off. The clock should be set correctly so the statistics on the operator screen Games Played by Day and Time will be right. The time on the clock also determines when the high score table is cleared. If you set the Clear High Score Table option in the Game Options screen to clear every week or every other week, then the high score table is cleared the first time the simulator is turned on after Wednesday midnight. You may need to turn on the clock if the simulator has a program crash. Turn off the clock only if you plan to store the simulator more than six months. (The clock has a lithium battery that should last more than five years in normal use.) To turn off the clock, choose Clock Off from the clock submenu, shown in Figure 2-14. To turn on the clock, choose Start Clock from the menu. In about two seconds, the clock starts. If the clock is losing or gaining time, then use Clock Faster or Clock Slower to adjust the calibration of the clock. Choose the item you need from the menu by using either coin switch. Change the setting by turning the key until you see the correct time. The items on the clock menu are explained below. + Exit returns you to the Test menu. ¢ Inc Hours changes the hour setting ahead.

  • Inc Minutes changes the minute setting ahead.
  • Inc Seconds changes the second setting ahead.
  • Inc Day changes the day of the week (for example, Monday or Tuesday) setting ahead.
  • Inc Month changes the month setting ahead.

ONDA DECEMBER 10, 1990

Figure 2-14 Set Clock Screen

Page 25
  • Inc Date changes the date setting ahead.
  • Inc Year changes the year setting ahead.
  • Faster Clock changes the calibration setting ahead. Each increase in the calibration setting makes the clock run about 5 seconds faster per month.
  • Clock Offturns the clock off. ¢ Dec Hours changes the hour setting back. ° Dec Minutes changes the minute setting back. ° Dec Seconds changes the second setting back. ° Dec Day changes the day of the week (for example, Monday or Tuesday) setting back. ° Dec Month changes the month setting back. © Dec Date changes the date setting back. ° Dec Year changes the year setting back.
  • Slower Clock changes the calibration setting back. Each decrease in the calibration setting makes the clock run about 5 seconds slower per month. © Start Clock starts the clock.

Disable Broken Controls Screen

Use this screen, shown in Figure 2-15, if you have a broken shifter, brake pedal, or clutch pedal, and cannot repair it immediately. Before you use this screen use the Set Controls screens and tread the information about the control in Chapter 3. Disable these controls only as a temporary measure so you can continue to operate the simulator. If you disable a control, the realistic driving feel of that control is lost. Earnings could drop. If you have disabled a control, remember to choose working after you repair it.

Special Functions Screens

Use the items on this screen, shown in Figure 2-16, if a system or board failed the program RAM and ROM test or the board and microprocessor test in the automated self-test. Also use this screen if you have problems with the steering wheel, the shifter, or if the clock settings or the statistics are erratic. A short summary of when to use these items is shown in Table 2-5. The Special Functions items are explained below. « Exit returns you to the Test menu. Self-Test

ey to save etting and ¢

Figure 2-15 Disable Broken Controls Screen. Multisync Board GSP Tests should be used if you get the message Bad GSP VRAM or Bad GSP Color RAM in the automated self-test. This screen has six tests you can use. Multisync Board Controls gives you most of the same information as provided in the Control Inputs screen plus five steering wheel tests, a line voltage calibration screen, additional shifter tests, and a link connect test. (All controls are “Multisync board” controls.) Multisync Board ROM Checksums should be used if you get the message Bad Program ROM in the automated self-test. This tests the program ROMs individually and shows the results on the screen. Multisync Board ZRAM Tests should be used if your controls settings are changing or erratic even though you used the Set Controls screen, Also use these tests if you suspect the simulator is not keeping the statistics correctly.

Figure 2-16 Special Functions Screen

2-13

Page 26

Self-Test

Special Function Items Table 2-5 When to Use the

  • ADSP Board Tests should be used if you get any message other than ADSP Board OK for the ADSP board test in the automated self-test. This screen has three tests and an ADSP ROM checksum test. It also has eight “scope loop” tests for factory use only since they require schematics and an oscilloscope.
  • Sound Board Tests should be used if you get the message Bad Sound Board in the automated selftest. However, many of the sound board tests are for factory use only since they require schematics and an oscilloscope.
  • DSK Board Tests should be used if you get the message Bad DSK Board in the automated self-test. This screen allows you to test the DSK ROMs, the DSK RAM, the DSK ZeroPower RAM (ZRAM), and the two ASIC subsystems. It also has a Special Functions screen for factory quality assurance.

Multisync Board GSP Tests

If the automated self-test reports bad VRAMs, choose Multisync Board GSP Tests and the screen in Figure 2-16 appears. First run the VRAM simple test. It gives the location of the bad VRAMs, If the VRAMs pass this test, but you think the simulator has a bad VRAM, run the VRAM verify test. ° VRAM Simple Test is the same test that is run in the automated self-test. It is run by the 68010 through the GSP interface and detecis open or shorted address or data lines or missing parts. The results are displayed on-screen with a picture showing the VRAM section of the Multisyne PC board. The good parts are shown in green and the bad parts are shown in red. If an entire section appears in red, the problem may be with a buffer associated with that section. The test takes about 30 seconds.

  • VRAM Verify Test is a complete memory test run by the GSP. The results are reported on the screen like in the simple test. The test takes about three minutes to run. Since the verify test is run by the GSP program in the VRAMs, a single bad VRAM can cause the GSP program to crash. When this happens, the 68010 microprocessor reports that all the VRAMs are bad, although probably only one VRAM is bad. You must run the VRAM complete test (described below) to find out which VRAM is bad. If the VRAM verify test fails, but the VRAM simple test shows the VRAMs are good, you should run the VRAM complete test. If the verify test runs and reports that the VRAMs are good, then the VRAMs should be good.
  • VRAM Compiete Test is a complete memory test run by the 68010 through the GSP interface. Because the 68010 runs the test, a single bad VRAM does not cause the test to report all the VRAMs are bad {as it does the verify test). Any VRAMs that are bad are shown on the screen at the end of the test, This test takes at least 22 minutes to run.

Figure 2-17 GSP Tests Screen

Page 27

Self-Test

Figure 2-18 Multisync Board Controls Screen

  • Test VRAM for Display Errors checks for video display problems.
  • Color RAM is the same test that is performed in the automated self-test. It tests the color RAM and reports the results. ° VRAM Shift Register Test checks the shift register part of the video RAMs.

Multisync Board Controls

This screen provides more information about the controls than is shown in the Control Inputs screen, The items on the screen are described below and shown in Figure 2-18. After you choose any item on this screen and go to that item, you can return to this screen by turning the key. e The Pots: 8 Bit screen has the same information as the Control Inputs screen. This screen appear in Figure 2-19. It shows the voltage inputs from the control potentiometers to the A/D converter circuits. As you use a control, the line on the screen changes as the voltage input changes. If the line does not change, see the information about that control in Chapter 3. The Brake Force line shows the force on the brake pedal. As you push harder and harder on the brake, the line should disappear. 0 Volts appears as no line or a short line on the screen, and 5 Volts appears as a line halfway across the screen. e Pots: 12-Bit screen is not used. e Steering Wheel screen submenu is explained below and shown in Figure 2-20. e Duart does not apply to this simulator. ° Link Connector tests the RS232 channel used to link two simulators together. Figure 2-19 Pots: 8-Bit Screen

Steering Wheel Submenu

Use these item if you have a problem with the steering assembly. The screen is shown in Figure 2-20. You will need to read the section Steering Assembly in Chapter 3 to find out how to use the tests. To move through the menu and the screens, use the coin switches. To exit a screen, push both coin switches down. e Exit returns to the Multisync Board Controls screen. e Send Force sends a steady force to the motor amplifier PCB. See Figure 2-21. e Sine Wave sends a sine wave force to the motor amplifier PCB. This screen is similar to Figure 2-21. e@ Square Wave sends a square wave force to the motor amplifier PCB. This screen is similar to Figure 2-21. e Triangle Wave sends a triangle wave force to the motor amplifier PCB. This screen is similar to Figure 2-21,

Figure 2-20 Steering Wheel Submenu Screen

Page 28

Self-Test

Figure 2-21 Send Force Screen

e Closed Loop Test reads the steering wheel position and sends a force to the motor amplifier PCB to simulate a simple spring. e Life Testis a test for factory use only.

CAUTION Do not use the Life Test. It is used only in the factory for testing of potentiometers. If you leave the simulator in this test for a long time, you can destroy the potentiometer on the steering assembly.

Link Connector Test

Use this test if you have a problem when linking two simulators together. This test requires a special test connector. plugged into the Link Connector on the game. The special test connector is a female DB-25 with pins 2 and 3 connected together. Contact Atari Games Customer Service on how to obtain a test connector. The test results are displayed (in color) as shown in Figure 2-22.

Multisync Board ROM

Checksums

This screen checks the Multisync PC board program ROMs for errors. Use this test if you have a bad program ROM message in the automated self-test or you suspect program ROM failure. To exit this screen, turn the key. When the checksum test is complete, a hexadecimal number follows each ROM as shown in Figure 2-22. The first two digits in each hexadecimal number can be any number, but the last two digits must be the ones shown in Figure 2-23.

Multisync Board ZRAM

Test

This test checks the non-volatile RAM where the simulator statistics and control set-up values are kept. Check the ZRAMs if you think the statistics are incorrect. Also use this test if the contro] settings are changing, even though you have recently set them with the Set Controls screens. If the simulator loses power or is reset while it is in this test, then the statistics and the control settings will be lost. If this happens, use the Set Controls item from the Multisync menu to eset the controls. The statistics cannot be restored.

ONNECTOR TES

A ROGH o

DUARTIndLOoc,P
TER06004006
ciEL ARS23306606 = XX0604206
NVECH00808KOS00200
RSav:95ov60909
EDés00:90000NO00
0000000o000Ax
sQUIRES 4SP:OR
E00:0090%,00000
GGEDINTOCONOR ONTHE
ayesOn ISALEDB
‘iDOGETHER
OoAGAUSTOO0OoBONO

Ob 6

Figure 2-23 ROM Checksums Screen

Page 29

ADSP Board Tests

Use this item if the ADSP PC board fails the microprocessor and board tests performed in the automated self-test. When you select ADSP Board Tests from the Test menu, the screen in Figure 2-24 appears. The items on the screen are explained below.

  • Exit returns to the Test menu. « ADSP RAM Tested by 68010 tests the memory on the ADSP PC board. The 68010 on the Multisync PCB test the ADSP program memory, the ADSP data memory, and both ADSP output buffers. The memory tests are the standard, complete tests but are tun at the 68010's bus speed, which is slower than that of the 2160. « ADSP Program Memory Test .2100. is a standard, complete memory test run by the 2100 on it own program memory. Since the test program must reside in memory, a bad program RAM may prevent the test from running. However, because the program memory is divided into two banks, the test is divided into two parts. The program to test the upper bank is run from the lower bank; the program to test the lower bank is run from the upper bank. Unfortunately, the 2100 always starts operating from a specific address in the lower bank. Therefore, the lower bank must be operating to the extent that it can execute a JUMP instruction to the upper bank. These tests operate solely with program memory; they do not require that any data memory be operational. ° ADSP Data Memory Test is a standard, complete test run by the 2100. It operates solely with program memory and does not require that any data memory be functional. 2100 Test checks the response of the 2100 integrated circuit on the ADSP PC board by copying data from one location to another using a 2100 program. IRQ Test checks if the ADSP can generate interrupts for the 68010. « ROM Checksums tests the graphic ROMs on the ADSP PC board. When the checksum test is complete a hexadecimal number follows each ROM as shown in Figure 2-25. The first two digits in each hexadecimal number can be any number, but the last two digits must be the ones shown in Figure 2-25. If the last two numbers are different, then the ROM is bad or it is not on the board. ¢ ADSP Special Functions performs hardware diagnosis for use by a repair technician. Self-Test

Figure 2-24 ADSP Board Tests Screen

Sound Board

Use these tests if the sound PC board failed the microprocessor and board tests in the automated self-test. If the sound PC board failed the test, select this item from the Test menu and Figure 2-26 appears. Many of the tests require an oscilloscope and schematics. These are indicated on the list below. The tests are explained below.

  • Exit returns to the Test menu.
  • Play Sounds takes you to the Requesting Sound Screen. Follow the instructions on the screen to hear the simulator sounds.
  • Self-Test checks the sound program ROM and RAM, COMRAM, and 320 RAM.
  • SD ROM Checksums tests the ROMs holding the waveform data. The screen appears in Figure 2-27. It shows the ROM location, a hexadecimal number, and the results of the test for each ROM. The result will be one of the following: NE—Nothing is loaded in that socket. No action is required. BAD—The ROM is bad. OK—The ROM is OK. PROG DEV—The ROM is a program development ROM. 320 Sweep—Runs a program in the sound PC board 32010 to generate a sine wave sweep from 20 Hz to 9 KHz (requires oscilloscope). 320 Tune—Runs a program in the sound PC board 32010 to play a tune. Program ROM—Tests the sound PC board program ROMs with the sound PC board 68000 and reports the results on the screen.

2-17

Page 30

Self-Test

Figure 2-25 ADSP ROM Checksums Tests Screen

Program RAM—Tests the sound PC board program RAMs with the sound PC board 68000 and reports the results on the screen. COMRAM—Tests the sound PC board communications RAM with the sound PC board 32010 and reports the results on the screen. 320 RAM—Tests the sound PC board 32010 program RAM with the sound PC board 68000 and reports the results on the screen. LED Test—Flashes the Test LED with the sound PC board 68000. DAC Ramp—Writes to every DAC value with the sound PC board 68000. The sawtooth frequency is about 60 Hz (requires oscilloscope). DAC 250 Hz—Witites to every fourth DAC value with the sound PC board 68000. The sawtooth frequency is about 250 Hz (requires oscilloscope). SA Counter—Creates an oscilloscope loop for the sound address counter (requires oscilloscope). SB Latch—Creates an oscilloscope loop for the sound block latch (requires oscilloscope). 320 Tone—Plays a sine wave tone created by the 32010 (requires oscilloscope). 320 IRQ—Generates interrupts with the 32010 which the 68000 on the sound board recognizes (requires oscilloscope). 320 DAC Ramp—tThe sound PC board 32010 ramps the DAC (requires oscilloscope). 320 DAC Ones—The sound PC board 32010 writes walking ones through the DAC latch (requires oscilloscope). 320 SBLOCK—The sound PC board 32010 writes increasing addresses to the Sound Block Latch (requires oscilloscope).

DSK Board Testis

The DSK board is part of the Driver Speed Kit and turbocharges the simulator. The DSK board features:

  • extra RAM for storing player races
  • extra non-volatile RAM for remembering the Championship Lap ¢ extra ROM
  • two separate ASIC systems for increasing the performance level of the simulator The DSK Board Test screen is shown in Figure 2-28. ¢ DSK ROM Checksums tests the ROMs on the DSK board. ° DSK ZRAM test the additional non-volatile RAM used for storing the race of the Challenge Lap champion.

OUND BOARD

Figure 2-26 Sound Board Tests Screen

2-18 Figure 2-27 Sound Board Sound Wave ROM Checksums

Page 31

Figure 2-28 DSK Board Test Screen

The remaining tests on the menu (ASIC 61xxxx, ASIC 65xxxx, and DSK Special Functions) are used by the factory for quality testing.

LEDs on the Multisync PCB

The LEDs (light-emitting diodes) on the Multisync PCB show you the status of various signals on the Multsync PCB. Using the LEDs, you can check signals from Self-Test

various circuits going to the 68010 processor. The state of the signals is indicated by the LEDs which flash or stay lit. Figure 2-29 shows the location of the LEDs on the Multisync PCB. Table 2-6 shows the possible status of the LEDs, with an explanation of what they indicate.

DIP Switches

If you try to enter the self-test, but nothing appears on the screen, use the DIP switch tests. Use the information from these diagnostic tests to help you find the problem. Before you begin with these following tests, be sure that the problem is in the simulator hardware, not in the video display. If you have a completely dark screen, check the following:

  • Do you have power to the video display?
  • Are the video display’s filaments lit?
  • Do you have high voltage to the video display? If the answer to any of these questions is no, then you have a problem in the video display. Check the video display service manual included with your simulator for suggested procedure, If you are sure that the problem is not with the video display, then try the DIP switch diagnostics shown in Table 2-8. These tests isolate various ICs and systems for troubleshooting. The results of the tests are indicated by the Multisync PC board LEDs or on the video display screen.

Table 2-6 LED Status

2-19

Page 32

Self-Test

Setting the DIP Switches for the Tests

  • Put a jumper across the DIAGN test points, shown in Figure 2-29,
  • Select the diagnostic test you want to use with the DIP switch settings.
  • Turn on the self-test switch.

4, Put a jumper momentarily across the RESET test points, shown in Figure 2-29. Changing to Another DIP Switch Test

  • Change the DIP switch settings. 2, Put a jumper momentarily across the RESET test points, shown in Figure 2-29.

DTACK LED

Run LED Ending the DIP Switch Testing

  • Take the jumper off the DIAGN test points.
  • Put a jumper momentarily across the RESET test points. The DIP switch settings are on in the top position when the Multisync PCB is in the simulator.

Clock LED

IRQs LED

Reset Points

Test LED 2

Test Lep41

Diagnostic Points

DIP Switch

Figure 2-29 DIP Switch and LED Locations on the Multisync PCB

2-20

Page 33

Race Drivin’ Compact Self-Test

Table 2-7 Using the DIP Switches

_ Watchdog, Test $ “=. Puts thé 68010-in'a loop. Does ot clear the watchdog ‘counter. Th program RAM does not need to work. If the watchdog is wor run LED; DTACK LED, aid IRQs LED flash at 2 Hz and:

= Tests the test SLE The program RAM does not need to w

test LEDs are worn they flash at 2Hz.

test LEDs are worn they flash at 2Hz good. If ROM 0 Lis bad, LED'1 does not flas!

LED 2 does not flash. Tests. RAM 0 H and OL, which run the test menu. ~ about 5 seconds.) LED 1 and LED 2 flash together good. If RAM 0 Lis bad, LED 1 does not flash. If RAM 0H is ba LED 2 does not fash. ey ee a ‘ GSP Tests .

‘GSP Communications Tests if the 68010 can communicate with the GSP, which odie:

“the video. If the GSP responds, the LEDs flash together. If tie GSP does not respond, LED 1 and 2 flash alternately. Red ‘Screen » Produces a red screen from ‘the color RAM, regardless of GSP.

does not respond, LED 1 and 2 flash alternately input. Use this to check the red video. outputs. o :

Green Screen Produces a green screen from the color RAM, regardl Blue Screen’ "Produces a blue screen from the’ color RAM, “regal rdless of GSP Memory Fill Does a very slow GSP oe fill so you

ait £8 oct input. Use this to hieele the green video outputs.

S 7 input. Use this to check the blue video ‘outputs.

GSP VRAM Verify

/ROM Test Loop .

; “ ; _ > MSP Tests" MSP Interface ' Tests the: MSP interface. Results are displayed ‘MSP Auto Increment

The DTACK timer times out and generates a bus error (BERR signal. The rules are displayed. on the screen.

2-21

Page 34

Self-Test Race Drivin’ Compact

N O T E )

2-22

Page 35

CHAPTER 3

~ Maintenance and

Troubleshooting

This chapter includes maintenance, repair, and troubleshooting information for your Race Drivin’ Compact simulator. In the simulator, the hardware and software are closely related. If you are having problems with a mechanical assembly, always keep in mind that your electrical connections may not be good or you may have an electronic problem. To determine what kind of problem you have, always use the self-test screens as recommended for each

part. The first part of the chapter includes a schedule for simulator

maintenance and inspection, a table with genera] troubleshooting information, and a table of the voltage levels and test points on the PCBs. The rest of the chapter is arranged in alphabetical order by the name of the part or control. Under each part are maintenance procedures, troubleshooting tables and flowcharts, and repair procedures for the part. All exploded parts illustrations are printed in Chapter 4, Ilustrated Parts Lists.

Page 36

Maintenance and Troubleshooting

Maintaining and Inspecting

Preventive maintenance includes inspecting, cleaning, lubricating, and tightening hardware. Perform the preventive maintenance regularly so you can keep the simulator in top condition, avoid problems, and maximize your earnings. Preventive maintenance tasks and intervals are shown in Table 3-1. For the best performance from your Race Drivin’ Compact simulator, maintain your simulator according to the times shown in Table 3-1. Instructions for performing these tasks is explained in the section about that control in this chapter. You may want to perform these tasks more often if the simulator is heavily used. Table 3-2 shows the correct voltage levels to various PC boards and the test points for those voltage levels. Low voltages to PC boards may cause problems with the controls, with the video display, or in driving.

Regulated and supplied by the APU PCB. ‘Used. by the 12-bit A/D converter'and runs

Supplied and regulated by’

Used by the logic circuitry. TT ee

Se

Page 37

Maintenance and Troubleshooting

Table 3+ 3 Troubleshooting All becsiaeas

Table 3-3 is the first of ten troubleshooting tables in this chapter. Use this table if a// of your controls are acting erratically or not responding. If only one contrel is not working, go to the section about that control and read the troubleshooting information there.

Coin Mechanism

The coin mechanism should be cleaned every three months.

Maintaining the Coin

Mechanism

  • Turn off the power to the game. Open the upper coin door,
  • Open the gate on the door covering the magnet. Use the blade of a screwdriver to scrape away any metal filings collected on the magnet.
  • For a thorough cleaning, wash the coin mechanism in hot soapy water. Use a toothbrush to remove any stubborn build-up of residue in the coin path. Dry the coin mechanism with compressed air. Wook If you do not want to use water, bush the loose dust off with a soft brush and scrub the residue in the coin path with a toothbrush. Blow all the loose dust and dirt out with compressed air.
NOTE Never lubricate the coin mechanism with oil or grease.

Dashboard

Generally you do not need to remove the dashboard to work on the controls. You can work on the key switch, shifter, and steering assembly without removing the dashboard. To remove these controls from the cabinet, see the section on that control for information. Removing the Dashboard

  • Turn off the power to the game.
  • Remove the three tamperproof screws and washers in the cover plate of the steering whee]. Take off the steering wheel and cover plate. See Figure 4-2.
  • Open the back service panel. Remove the nuts on the six carriage bolts through the bottom of the cabinet shelf and push the carriage bolts through the cabinet shelf. 4, Also remove the nuts on the two cartiage bolts through the front of the dashboard. These bolts have spring nuts on them and you cannot push them through the cabinet.
  • Disconnect the key switch harness, abort button harness, and shifter harness from the simulator harness,
  • In the front, remove the four low crown nuts on the side carriage bolts. Remove the carriage bolts. Take the dashboard off the game,

Installing the Dashboard

Put the dashboard on the cabinet. Push the harnesses through the cutouts. ~

  • Loosely install the cartiage bolts and low-crown nuts on the sides of the dashboard.
  • Go to the back of the cabinet and install the fender washers and nuts on the carriage bolts on the front of the dashboard. 4, Insert the other carriage bolts through the bottom the dashboard and put the washers and nuts on them. Connect the key switch harness, abort button harness, and shifter harness to the simulator harness, w
  • Tighten the low-crown nuts on the sides of the dashboard.
  • Put on the steering wheel. Install] the three tamperproof screws and washers through the center cover plate.
Page 38

Maintenance and Troubleshooting

Interior Components

All the components in the interior of the simulator should be cleaned every three months. This includes the PCBs, the power supply and the video display.

Cleaning the Interior

Components

Perform the following procedure to clean the components inside the cabinet. i. Open the rear service door and the top service door.

WARNING Turn off the AC power, but do not unplug the power cord before cleaning inside the cabinet. The power cord provides a ground path for static voltage that can be present on the cleaning tools.
  • Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the power supply, PCB assemblies, and video display thoroughly.
CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Do not touch the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush,

Replacing the Spring in the Key Switch Assembly

Table 3-4 lists what can go wrong with the key switch assembly.

Oiling the Key Switch Assembly

Oil the key switch spring and shaft when turning the key switch becomes difficult, or when the key squeaks. 1, Turn off the power, Remove the back service door. 2, Remove the nuts and washers on the carriage bolts that hold the key switch assembly on the dashboard. Take the key switch out of the game. al Lightly oil the shaft and spring of the key switch. See Figure 4-5. Check that the spring is not broken. If it is, then replace the spring following the procedure under Repairing the Key Switch. 4, Replace the key switch in the dashboard. Put the nuts and washers on the carriage bolts that hold the key switch on the dashboard. Tighten the nuts.

If nothing happens when the key turns, and there is no resistance to turning, you may need to replace the spring.

  • Turn off the power. Remove the back service door. 2, Remove the nuts and washers on the carriage bolts that hold the key switch assembly on the dashboard. Take the key switch out of the game.
  • Remove the retaining ring from the back of the key switch case. See Figure 4-5. 4, Loosen the socket-head screw on the brass actuator with a 5/32-inch Allen-head wrench.
  • Remove the other retaining ring inside the case. Pull out the key. Take out the brass actuator, the old spring, and the nylon washer.
  • Put lithium grease (Atari Games part no, 107029- 002) on the housing where it touches the shaft. Wipe off the excess grease.
  • Put one end of the spring into the hole in the side of the case.
  • Push the shaft back into the case far enough to mount the spring on the shaft. You may have to cut the legs of the spring to the correct length so that they do not interfere with the operation of the switch assembly.
  • Put the brass actuator into the case with the actuator pin facing the key and opposite the switch. Catch the free end of the spring under the pin. Push the actuator and the nylon washer onto the shaft.
  • Push the shaft through the case and install the two retaining rings. ras . Adjust the actuator on the shaft until it is parallel to the roller on the switch.
  • When the actuator is against the case opposite the switch, the key should be vertical. If the key is not vertical, turn it until it is. Tighten the screw on the actuator.
  • Use a piece of a manila folder or any other flat material about .015 inches thick to adjust the switch distance. Hold the actuator against the side of the assembly with the flat piece of material between the actuator and the switch. The switch should
Page 39

press against the material. Tighten the screws on the switch to hold it in place. Release the actuator. Check the setting. When you turn the actuator against the switch, the switch should click but not be pressed all the way to the switch body. 14, Replace the key switch in the dashboard. Put the nuts and washers on the carriage bolts that hold the key switch on the dashboard. Tighten the nuts.

Tightening the Screw in the

Key Switch Actuator

If nothing happens when the key turns, and it turns more than 90°, you may need to tighten the screw on the actuator,

  • Turn off the power. Remove the back service door.
  • Remove the nuts and washers on the carriage bolts that hold the key switch assembly on the dashboard. Take the key switch out of the game.
  • Adjust the actuator on the shaft until it is parallel to the roller on the switch. See Figure 4-5. 4, When the actuator is against the case opposite the switch, the key should be vertical. If the key is not vertical, turn it until it is. Tighten the screw on the actuator.
  • Use a piece of a manila folder or any other flat material about .015 inches thick to adjust the switch distance. Hold the actuator against the side of the assembly with the flat piece of material between the actuator and the switch. The switch should press against the material. Tighten the screws on the switch to hold it in place. Release the actuator. Check the setting. When you turn the actuator against the switch, the switch should click but not be pressed all the way to the switch body.
  • Replace the key switch in the dashboard. Put the nuts and washers on the carriage bolts that hold the key switch on the dashboard. Tighten the nuts. Maintenance and Troubleshooting

Replacing the Switch on the Key Switch Assembly

Replace the switch if the key turns but nothing happens and the problem is not the spring, the actuator, or the connections. The key switch assembly is shown in Figure 4-5.

  • Turn off the power. Remove the back service door.
  • Remove the nuts and washers on the carriage bolts that hold the key switch assembly on the dashboard. Take the key switch out of the game.
  • Remove the two Phillips-head screws that hold the snap-action switch on the key switch assembly. Take off the switch. Take the harness off the switch.
  • Install the switch on the assembly, but do not tighten the screws. The roller on the switch should face the brass switch actuator.
  • Loosen the screw on the brass actuator. Adjust the actuator on the shaft until it is parallel to the roller on the switch.
  • When the actuator is against the case opposite the switch, the key should be vertical. If the key is not vertical, turn it until it is. Tighten the screw on the actuator.
  • Use a piece of a manila folder or any other flat material about .015 inches thick to adjust the switch distance. Hold the actuator against the side of the assembly with the flat piece of material between the actuator and the switch. The switch should press against the material. Tighten the screws on the switch to hold it in place. Release the actuator. Check the setting. When you turn the actuator against the switch, the switch should click but not be pressed all the way to the switch body.
  • Put the harness on the new switch. Connect the black wire to the C (or COM) terminal, and the white wire to the NO terminal.
  • Replace the key switch in the dashboard. Put the nuts and washers on the carriage bolts that hold the key switch on the dashboard. Tighten the nuts.

Table 3-4 Troubleshooting the Key Switch

Key does not return to center when tumed and: it has no resistance: ©... 5 Key turns moré that 90°. Key turns, but nothing happens. Key squeaks when turned. 4 te : Check the snap-action switch, swit and harness connections. “Oil the shaft'and’spring.

3-5

Page 40

Maintenance and Troubleshooting

Pedals

The construction for all the pedals is very similar. The main difference is that the brake has a strain gauge and connector bonded to the pedal. The strain gauge transmits information about the force on the brake to the Multisync PCB. The gas and clutch pedals use potentiometers to transmit position information to the Multisyne PCB.

If the Gas or Clutch Pedal

Does Not Work

Before you do any repairs, always perform the Se¢ Controls screens in the self-test; then try the pedal to see if this corrects the problem. If that does not repair the problem see Table 3-5, Troubleshooting the Gas and Clutch Pedal and follow the flowchart in Figure 3-1. If you must repair the clutch, but you cannot do so immediately, disable the clutch circuit. (You cannot disable the gas pedal circuit.) If you disable the clutch circuit, drivers can only use the automatic transmission mode, To disable the clutch circuit, go to the Disable Broken Controls screen in the self-test and choose broken for the clutch. Disable the clutch only as a temporary measure. Repair the clutch as soon as possible since this is an essential part of the game

If the Brake Pedal Does Not Work

If you have problems with the brake, make sure the simulator has been on for at least 10 minutes. The brake may not work right if the simulator has not been on long enough. Before you do any repairs, always perform the Set Controls screens in the self-test but only after the simulator has been on at least 10 minutes. Try the brake to see if this corrects the problem. If that does not fix the problem, see Table 3-6, Troubleshooting the Brake Pedal, and follow the flowchart in Figure 3-2. If you decide you must check the strain gauge, follow the procedure in Testing the Brake Pedal Strain Gauge and Bonding section. If you must repair the brake, but you cannot do so immediately, and you want to continue to use your game, disable the brake circuit. When you disable the brake, a screen appears before each race which tells each driver that the brake does not work; if he wants to slow down, he should take his foot off the accelerator. To disable the brake circuit, go to the Disable Broken Controls screen in the self-test and choose broken for the brake. Disable the brake only as a temporary measure. Repair the brake as soon as possible, since this is an essential part of the game.

Greasing and Checking the

Grease the pivot shafts every three months with multipurpose white grease (Atari Games part number 178027-001).

  • Turn off the power to the simulator.
  • Take each pedal assembly out of the simulator. Remove the two button-head and two tamperproof screws and washers holding the assembly in the cabinet. Unscrew the two screws holding the gas pedal to the floor if you are removing the gas and brake pedal assembly. See Figure 4-6 for the brake and gas pedals and Figure 4-7 for the clutch pedal.
  • Pull the assembly forward and disconnect the pedal harness(es) from the simulator harness. 4, Put white grease on the pin holding the lower and upper links together. Work the grease around on the pivot shaft.
  • Check the parts of the pedal to make sure they are working correctly. Check and tighten (if necessary) the jam nuts on the links and the screw at the end of the pedal shaft. Tighten any other screws that have come loose.
  • Install the assembly in the cabinet. Attach the pedal harness to the simulator harness.
  • Install the screws and washers.

Replacing a Pedal

Replace a pedal only if the pedal or the pedal shaft is broken. If the pedal is wobbly, tighten the screw that holds the pedal in the pivot shaft.

Removing a Pedal

  • Turn off the power to the simulator.
  • Take the pedal assembly out of the simulator by removing the two button-head screws and two tamperproof screws and washers holding the assembly in the cabinet. Unscrew the two screws holding the gas pedal to the floor if you are removing the gas and brake pedal assembly. See Figure 4-6 for the brake and gas pedais and Figure 4-7 for the clutch pedal.
  • Pull the assembly forward and disconnect the pedal harness(es) from the simulator harness. 4, Remove the lower link if you are working on the clutch or the gas pedal.
Page 41
  • Remove the hex-head screw that holds the pedal on the shaft. Pull off the pedal. Maintenance and Troubleshooting
  • Install the screws and washers that hold the assembly in the cabinet.
WARNING The springs will pop when you take off the pedal. Keep your fingers away from the springs.

Installing a Pedal If you are installing a brake pedal, do not install the pins in the connector or put the tie wrap on the pedal until the pedal is installed in the assembly.

  • Before you put the pedal in the assembly, turn the pivot shaft so the hole in the pivot shaft with the square cut-out around it is pointing towards the front of the assembly. See the detail in Figure 4-6. 2, Make sure the spring(s) are hooked over the spring anchor shaft. Hook a screwdriver through the springs from the back of the assembly to hold them in tension. This makes it easier to insert the pedal through the springs and into the hole in the pivot shaft. With the springs held in tension, insert the pedal into the pivot shaft.
  • Put the hex-head screw into the end of the pedal in the pivot shaft,
  • Grease the pin that holds the lower and upper links together.
  • Attach the lower and upper links together with the pin. Set the upper link so it is 22° clockwise from vertical.
  • If you have installed a brake pedal, put the tie wrap on the the pedal shaft to hold the wires in place. Insert the pins into the connector.
  • Put the assembly in the game. Connect the pedal harness(es) to the simulator harness.
NOTE Enter the self-test and go through the Set Controls screens because you replaced the pedal. Otherwise the simulator will not work correctly.

Replacing a Spring

Replace the pedal spring(s) if they are weak, broken, or sprung.

  • Turn off the power to the simulator,
  • Take the pedal assembly out of the simulator by removing the two button-head and two tamperproof screws and washers holding the assembly in the cabinet. If you are working on the brake and gas assembly, remove the screws holding the gas pedal to the floor. See Figure 4-6 for the brake and gas pedals and Figure 4-7 for the clutch pedal.
  • Pull the assembly forward and disconnect the pedal harness(es) from the simulator hamess,
  • Remove the lower link if you are working on the clutch or the gas pedal. Remove the hex-head screw that holds the pedal on the shaft. Pull off the pedal. wu
WARNING The springs will pop when you take off the pedal. Keep your fingers away from the springs.
  • Take the pedal assembly off the front metal plate by removing the four nuts on the carriage bolts.
  • Remove the bumper shafts, spring shafts and support shafts, which hold the assembly together.

Table 3-5 Troubleshooting the Clutch or Gas Pedal

| Pedal does not work or works erraticall

Page 42

Maintenance and Troubleshooting

You have tried the SET CONTROLS screen, Goto the CONTROL INPUTS sereen in the selltest,

Does le Bit AD ine fore contol ave smoot when you operate the conto?

Check the ZRAM in SPECIAL FUNCTIONS inthe salttest Dotre oer ines onthe sowen move smoothly when tose ctner conta are operated? Troubleshoot the 8-bit A/D circuit on the main PCB.

Repair

wene gears. sprig, endior cables connected tothe potentomete working, ‘ ubicted? Repair

Isthe potentiometer insialed corecty andisthe nut tight? Repair

‘Check the voltage atthe control input to the meln PCB. See the schemas.

Does ne vollage input vary When you ‘operate the conto? Replace the potentiometer

‘Troubleshoot the bit AD circuit ‘on the main PCB.

Figure 3-1 Clutch or Gas Pedal Is Not Working or Is Working Erratically and You Have Tried the Set Controls Screens

Page 43

8.

9.

10.

a

12.

13.

15.

16.

VW

18. Replace the spring(s). If the pedal has two springs, replace both of them. Lubricate the pivot shaft with multi-purpose grease before you put it back into the assembly. Assemble the shafts in the pattern shown in Figure 4-6 for the gas or brake pedal or Figure 4-7 for the clutch pedal. If you have disassembled the brake pedal, be sure to put the large brake bumper and bumper shaft on the bottom, . Iostall the pedal assembly on the front metal plate with the four nuts and washers on the carriage bolts. Before you put the pedal in the assembly, turn the pivot shaft so the hole in the pivot shaft with the square cut-out around it is pointing towards the front of the assembly. See the detail in Figure 4-6. Make sure the spring(s) are hooked over the spring anchor shaft. Hook a screwdriver, or any other long thin piece of metal, through the springs from the back of the assembly to hold them in tension. This makes it easy to insert the pedal through the springs and into the hole in the pivot shaft. With the springs heid in tension, insert the pedal into the pivot shaft. . Put the hex-head screw into the end of the pedal in the pivot shaft. If you are working on the clutch or gas pedal, grease the pin that holds the links together. Attach the lower and uppez links together with the pin. Set the upper link so it is 22° clockwise from vertical, Tighten the jam nut on the lower link on the pivot shaft. Put the assembly in the game. Connect the pedal harness(es) to the simulator harness. Install the Screws and washers that hold the assembly in the cabinet.

Replacing the Clutch and

Gas Pedal Potentiometers

Do not replace a potentiometer until you have performed the Se¢ Controls screens. Check to see if that solves the problem. If not, follow the flowchart in Figure 3-1 to make sure that the potentiometer is the problem.

2. Turn off the power and unplug the game. ‘Take the pedal assembly out of the simulator by removing the two button-head screws and two tamperproof screws and washers holding the assembly in the cabinet. Remove the two screws that hold the gas pedal to the floor of the simulator. See Fig- Maintenance and Troubleshooting

ure 4-6 for the brake and gas pedals and Figure 4-7 for the clutch pedal. Pull the assembly forward and disconnect the pedal harness(es) from the simulator harness. 4, Take the wires off the potentiometer.

8.

9. Loosen the jam nut on the upper link on the potentiometer shaft. Remove the upper link. Loosen the 1/2-inch nut on the potentiometer shaft and remove the potentiometer. Install the potentiometer so the key is in the key slot at the top, the terminals point to the back of the assembly, and the flat of the shaft is facing up. Solder the wires onto the potentiometer in the order shown in Table 3-7. Install the assembly in the simulator. Connect the pedal harness(es) to the simulator harness.

  • Now switch on the self-test and go through the Set Controls screens.
NOTE Enter the seif-test and go through the Set Controls screens because you repaired the pedal assembly.

Testing the Brake Pedal Strain Gauge and Bonding

If you have brake problems, see the flowchart in Figure 3-2. If necessary, do the following tests to check the strain gauge and strain gauge bonding. 4, Put an obmmeter across pins 1 and 2 of the brake harness connector. If the ohmmeter does not measure 359 Q + 10%, the strain gauge is bad or the connection is bad. Replace the brake pedal and the strain gauge. If the ohmmeter does measure 350 Q + 10%, then check the bonding. Attach a digitai volt-ohmmeter to pins 1 and 2 and have someone press hard on the brake.

NOTE Use a sensitive ohmmeter to check the change in resistance since the change is only about 1 Ohm.

If the resistance does not change as the pressure on the brake pedal changes, then the bonding has failed and you must replace the brake pedal and the strain gauge.

Page 44

Maintenance and ‘Troubleshooting

‘Yeu have tried the SET CONTROLS sereen. Go to the CONTROL INPUTS soreen in the self-test.

Does. te BRAKE FORCE lne crange when you pera the conte?

Call Atari Games Customer Service. Has the game ppowerbeen ovat least 10 mines?

Does the brake LED on tne ‘main FOB cam when the brakes pressed hard? Wait for 10 minutes.

Fix the ZRAM, ‘Troubleshoot the 8-bit A/D circuit on the main PCB. Check the connectors and wiring from the brake pedal to the main PCB,

Check the strain gauge and the strain ‘gauge bonding.

Replace the fuse.

Figure 3-2 Brake Pedal Is Not Working or Is Working Erratically and You Have Tried the Set Controls Screens

Table 3-6 Troubleshooting the Brake Pedal

Pes

down on the brake, the li

much force you are putti

ee ey

3-10

Page 45

Table 3-7 Pedal Potentiometers Harness Connections

Replacing the Brake Strain Gauge

If you have tested the strain gauge and are sure that the gauge or the bonding is bad, you must replace the brake pedal with the strain gauge already attached since special bonding techniques are required. Follow the steps in Replacing the Brake Pedal.

Shifter Assembly

If you have problems with the shifter, check Table 3-8, Troubleshooting the Shifter Assembly. If you must repair the shifter, but you cannot do so immediately, and you want to continue to use your simulator, disable the shifter circuit. When you disable the shifter, drivers can only use the automatic transmission mode. To disable the shifter circuit, go to the Disable Broken Controls screen in the self-test and choose broken for the shifter. Disable the shifter only as a temporary measure. Repair it as soon as possible since this is an essential part of the simulator.

Lubricating the Shifter

  • Turn off the power. Open the back service door.
  • Remove the shifter from the dashboard. Remove the nuts and washers on the four carriage bolts that hold the shifter, shifter spacer, and shifter bezel on the dashboard. Take off the shifter, spacer, and bezel. Maintenance and Troubleshooting
  • Remove the six screws that hold the two halves of the shifter case together. See Figure 4-4. Carefully pull apart the case. The ball bearing can fly out since it is under compression. The spring will pop out too. 4, Lubricate the bal! bearing under the shifter handle and the shifter pattern in the bottom of the shifter. Use light-duty white grease, Atari Games part number 178027-091.
  • Reassemble the shifter and shifter spacer.
  • Put the shifter, shifter spacer, and shifter bezel back on the dashboard and install the carriage bolts, washers, and nuts that hold them in place. You may need someone to help you.

Replacing a Shifter Switch

Before you replace a switch, check the shifter switches on the Control Inpuis screen in the self-test. If a gear position number does not change from blue to green when you move the shifter into that position, then probably the switch or the connection is bad.

  • Open the back service door. Check the connections to the shifter. See Table 3-9. If the connections are correct and tight, turn off the power. Remove the four nuts and washers that hold the shifter, shifter spacer and bezel on the dashboard. See Figure 4-4. Take out the shifter, spacer and bezel.
  • Make sure the shifter handle is not engaging the switch you are replacing.
  • Carefully remove the switch on the shifter so the actuator pin and spring above the switch do not fly off and are lost.
  • Replace the switch. Install the pin and spring.
  • Connect the harness to the switch with the wires in the order shown in Table 3-9.
  • Assemble the shifter and shifter spacer and install them in the dashboard.
  • Reassemble the shifter and shifter spacer.
  • Put the shifter, shifter spacer, and shifter bezel back on the dashboard and install the carriage bolts, washers, and nuts that hold them in place. You may need someone to help you.

3-11

Page 46

Maintenance and Troubleshooting

Table 3-9 Harness Connections to the Shifter Switches

“Color of Harness Wire: ~ Brown, N.O-: Orange, N.O ~~ Yellow, N.O. “ Green; N. «Gear Position’

Speakers

If you have problems with a speaker, check Table 3-10, Troubleshooting the Speakers, before you replace it.

Removing a Speaker

. Turn the power off. Remove the back service door.

‘i Disconnect the connectors from the speaker that is

bad. Remove the screws that hold the speaker in the cabinet.

CAUTION Be careful when handling the speaker. The cone material is fragile and can be easily damaged.
  • Remove and replace the speaker. 4, Connect the speaker to the simulator harness. Make sure you attach the connectors correctly. The signal wire should be attached to the speaker terminal marked by color,a “+” sign, or a round dot. (The signal wire is indicated on the simulator wiring diagram in the Schematic Package.)

Static-Sensitive Devices

Devices

Be careful when you work with static-sensitive devices on the simulator PCBs. These devices can be microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSD devices that use metal-oxide semiconductor (MOS) technology.

Replacing Static-Sensitive

The static-sensitive devices can fail from a static charge that has built up in your body. They can also fail because of leakage from an improperly grounded soldering iron.

3-12 Before you handle a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that is earth-grounded. If you soldex a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. Before you replace a static-sensitive device, make sure that the device actually is defective. A static-sensitive device can appear defective due to leakage on a PCB. To check if a device is defective, ground any static voltages as described in the paragraph above. Clean both sides of the PCB with flux remover or an eraser. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Then test the device. A new Static sensitive device may be packaged in conductive foam or may have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Steering Assembly If you have problems with the steering assembly, check the troubleshooting suggestions in Table 3-11. Always perform the Set Controls screens in the self-test first. You should regularly go through the Set Controls screen to adjust the set points on the steering assembly to account for wear on the belt.

Oiling the Bronze Bearing The only bearing on the steering assembly that must be oiled regularly is the bronze pillow block bearing behind the steering wheel. See Figure 4-3. 1, Take off the back service door.

  • The bearing fill hole is on the right. Use an oil can with a flexible spout and put oil in the bearing.

Adjusting the Steering Belt The belt itself cannot be adjusted, but the limits of the steering movement can be changed to adjust for belt wear. You should do this every two months by going through the Set Controls screens. If the belt is very loose and resetting the set points does not improve the steering, then replace the belt.

Replacing the Steering Belt Replace the belt on the steering assembly if it is broken or loose. However, before you replace the belt because it is loose, use the Set Controls screen to see if this will fix the problem. By resetting the steering lim-

Page 47

Table 3-10 Troubleshooting the Speakers Maintenance and Troubleshooting

its on this screen, you can adjust the outputs to compensate for wear in the belt.

  • Turn off the power to the simulator. Take off the back service door.
  • Remove the belt by pushing the motor towards the steering wheel mounting shaft and working the belt off the pulleys. See Figure 4-3.
  • Install the new belt by pushing the motor towards the steering wheel mounting shaft and putting the belt on the pulleys. 4, Put oil in the fill hole on the bronze bearing on the steering wheel mounting shaft if you have not done this in the last three months. Replace the back service door. vw
NOTE You must enter the self-test and go through the Set Controls screens because you repaired the steering assembly. Otherwise the simulator will not work correctly.

Replacing the Steering

Motor Replace the steering assembly motor if you have fol- Jowed the flowchart in Figure 3-3, 3-5, or 3-6 and you are sure that the motor is the problem. Another reason to replace the motor is if the steering wheel is difficult to turn and the problem is not lubrication or the mechanical parts. Before you replace the motor, check the harness connections to make sure they are good.

Removing the Motor

  • Turn off the power to the simulator,
  • Remove the three tamperproof screws and washers in the cover plate of the steering wheel. Take off the steering wheel and cover plate. See Figures 3-8 and 3-9, 10.

12.

13. Take off the back service door. Disconnect the steering assembly harness from the simulator harness, Disconnect the motor power from the motor amplifier PCB assembly. Remove the screw down tie wrap from the side of the cabinet. Remove the four nuts that hold the steering assembly on the shelf. Push the screws through holes in the shelf. Remove the steering assembly. Remove the harness from the encoder PCB. Take off the two screws that hold the encoder PCB on the assembly. Remove the PCB. Remove the encoder disk, disk collar, and disk stiffening ring by loosening the socket-head screw on the disk collar. Remove the belt by pushing the motor towards the steering wheel mounting shaft and working the belt off the pulleys. Remove the pulley on the motor by loosening the socket head screw that holds it on. (The sockethead screw has a penetrating adhesive on it.) Remove the nut and hex-head bolt that holds the spring in tension. . Take off the 1/2-inch retaining ring at the front of the motor on the pivot shaft. Pull the pivot shaft out the back of the steering assembly. Remove the motor. Remove the four socket-head screws and washers on the front of the motor.

Installing the Motor 1. Install the pivot plate on the front of the motor. Align the bottom of the pivot plate with the bottom flat edge of the motor bezel. Install the four socket-head screws with the splitlock washers and flat washers that hold the pivot plate on the motor. Tighten the screws to 30 + 5 inch-pounds. Put the motor and pivot plate in the assembly with the label and harness on top.

Page 48

Maintenance and Troubleshooting

Table 3-11 Troubleshooting the Steering Assembly

e. "Control Inputs screen,

the Steering Wheel numbers do not ot change “the Steering Wheel numbers do not change the i Steering Wheel numbers do not change the words Center Edge do not ‘change from blue-to green, and there is no. Seating ‘3

‘And the Steering is erratic. :

and there is is no steering power. «=~

*-and the centering disk is scraping against . the optical readers.

blue to green, and the steering is erratic. the words Center Edge do not change from

power.

“the words Center Edge do not change from

blue to green, and the centering disk is scraping against the optical readers. Steering has no force or low force.

  • If you think thé steering «3-5 for more information.

©The encoder PCB or connections tt «, the connection, replace the harness, or replace the encoder PCB.

“4. Go through the Set Controls

. “Are the pulleys aligned: :

. Are the-pulleys:aligned?. Replace the bell

  • Push the pivot shaft through the frame, washers, motor, and pivot shaft as shown in Figure 3-4. Install the 1/2-inch retaining rings on the ends of the pivot shaft as shown in the figure.
  • Assemble the hardware that holds the spring in tension, See Figure 4-3. Install the parts on the bolt in the following order: a. 1/4-inch-long spacer. Hook the end of the spring around this spacer. b, Washer. c. 5/8-inch-long spacer. d. Washer,

3-14 Install the bolt with the hardware on the outside of the frame. Put the lock nut on the bolt inside the frame and tighten it to 212 + 20 inch-pounds. . Remove the socket-head screw from the pulley you took off the motor. Put a penetrating adhesive on the screw. Slide the pulley back on the motor shaft. Align this pulley to the other one. Turn the pulley so the screw hole is over the flat of the shaft. Install the socket-head screw. Tighten the screw to 50 + 8 inch-pounds. Install the belt on the pulleys.

Page 49

The steering wheel turns continuously during game play and you have already ‘ried the SET CONTROLS soreen

CONTROL INPUTS screen, clogs the wheel poston no. increase smoothly 28 you tum the wheel clock ‘wise? Does he positon no, ‘become 2er0 one eve Maintenance and Troubleshooting

Measure the vatage on the Two steering wheel poston inpus (on the main PCB. Does he input ‘itch rom 9 to SV ancback ‘when you ten the teeing wheel? Check the steering wheel harness. Check the steering wheel encoder and centering disks and PCBs.

Go to the MAIN BOARD CONTROLS screen and choose the STEERING WHEEL menu, Choose the TRIANGLE WAVE Test. ‘Troubleshoot the optical position circuit (on the main PCB. See the main PCB schematic,

‘slzting wheel force ‘change sooty fom clockwise to ofunterclockwise when you othe TRIANGLE WAVE Test? Hold ‘he stering whee when Check the motor amplifier PCB fuse and the abl from the main board tothe rotor ampifier assembly.

‘Check the motor amp PCB. you co this est,

Call Atari Games Gustomer Service,

Figure 3-3 The Steering Wheel Continuously Turns in One Direction and You Have Tried the Set Controls Screens

  • Put oil in the fill hole on the bronze bearing on the steering wheel mounting shaft if this has not been done recently.
  • Remove the screw from the disk collar. Put the encoder disk, collar, and stiffener on the motor shaft. Make sure the hole for the socket-head screw is facing out and is over the flat of the shaft.
  • Put on the encoder PCB. Make sure the optical readers and the harness connection face down. Move the encoder disk so it is between the two readers, but does not touch them, Tighten the screws on the encoder PCB to 10 + 3 inch-pounds.
  • Install the screw that holds the disk collar on the shaft and tighten it to 30 + 5 inch-pounds. Make sure the encoder disk does not move on the shaft.
  • Install the harness on the encoder PCB.
  • Before you install the steering assembly back in the simulator, turn the centering disk so the single hole in the disk is between the optical readers on the PCB. This will make it much easier to correctly install the steering wheel.
  • Put the steering assembly back in the cabinet. Install the four carriage bolts through the holes in the shelf. Tightly install the fender washers and nuts on the bolts so the assembly does not move.
  • Install the steering wheel with the center spoke down. Make sure the single hole on the centering disk is between the optical reader on the centering PCB so the steering wheel will be correctly centered. Put the center cover on the steering wheel. Install the three tamperproof screws and lock washers
Page 50

Maintenance and Troubleshooting

Steering Frame

Clip Ring

/ Clip Washer Ring Motor Assy

Figure 3-4 Installing the Steering Pivot Shaft

that hold the steering wheel on the steering assembly. Tighten the screws to 50 + 8 inch-pounds.

  • Connect the steering assembly harness to the simulator harness. Attach the screw down tie wrap on the motor-opto harness to the cabinet. Make sure the wires will not be caught in the motor pulley. Connect the motor power harness to the motor amplifier PCB.
  • Install the back service door.
NOTE You must enter the self-test and go through the Set Controls screens because you repaired the steering assembly. Otherwise the simulator will not work correctly.

Replacing the Encoder or Centering PCB

If you are having problems with the steering, and you have determined the problem is the encoder or the centering PCB by following the troubleshooting table, Table 3-11 or the flowchart in Figures 3-3, 3-5, or 3-6, then replace the PCB. If you are replacing the centering PCB assembly on the steering wheel shaft, part number 046691-01, you can replace it with the another centering PCB assembly or with the encoder PCB assembly, part number A046689-01. However, you must replace the encoder

3-16 PCB assembly with an encoder PCB assembly, part number A046689-01.

Removing the Encoder or Centering PCB

Turn off the power to the simulator.

  • Remove the three tamperproof screws and washers in the cover plate of the steering wheel. Take off the steering wheel and cover plate. See Figures 3-8 and 3-9.
  • Take off the back service door. Disconnect the steering assembly harness from the simulator harness. Disconnect the motor power harness from the motor amplifier PCB assembly. Remove the screw down tie wrap from the side of the cabinet. 4, Remove the four nuts that hold the steering assembly on the shelf. Push the screws through holes in the shelf. Remove the steering assembly. Remove the harness from the PCB you are replacing.
  • Take off the two screws that hold the PCB on the assembly. Remove the PCB. uw

Tnstalling: the Encoder or Centering PCB

Put the new PCB in place. However, do not screw it down until you check that the disk is between the optical readers and not touching either one. If the disk is not centered between the readers, loosen the socket-head screw on the disk collar and move the disk until it is centered. Tighten the screw to 30 + 5 inch-pounds to hold the disk in place. Tighten the screws that hold the PCB on the frame to 10 + 3 inch-pounds.

  • If you have not regularly oiled the bronze bearing on the steering wheel mounting shaft, put oil in the fill hole on the bearing.
  • Install the harness on the PCB.
  • Before you install the steering assembly back in the simulator, turn the centering disk so the single hole in the disk is between the optical readers on the PCB. This will make it much easier to correctly install the steering wheel.
  • Put the steering assembly back in the cabinet. Install the four carriage bolts through the holes in the shelf. Tightly install the fender washers and nuts on the bolts so the assembly does not move.
  • Install the steering wheel with the center spoke down. Make sure the single hole on the centering disk is between the optical reader on the centering PCB so the steering wheel will be correctly centered. Put the center cover on the steering wheel. Install the three tamperproof screws and lock washers
Page 51

Steering wheel is very jerky and you have already tied the SET CONTROL soreen Maintenance and Troubleshooting

‘CONTROL INPUTS screen, does the whee! pastion ra, increase ssmooily as you tur the wheel ck wise? Does the pasion ro, ‘pecome zeroonce every

Yes ease ‘he wotageon he “wo steering wresl postion inputs) ‘nthe main PCB. Does the input sail tom 010 5¥ and back wren youu he stoetng wheel? ‘Check steering wheel hamess. Check steering wheel encoder and centering sisks and PCBs.

Yes

Goto the MAIN BOARD CONTROLS screen and choose the STEERING WHEEL item. Choose the SEND FORCE Test ftom the submen. schema ‘Troubleshoot the optical position circuit ‘on the main PCB. See the main PCB

Go to the MAIN BOARD CONTROLS screen ‘and go into the steering wheel menu. Choose the TRIANGLE WAVE Test.

Des ine force change Srroothly from clockwise to counter << clockwise when you do this test? (Haid the steering whee! to feel the force change.) arnpliier assembly.

Call Atari Games Customer Service. Check the motor amplifier PCB fuse and the cable from the main board fo the motor

Check the motor amp PCB.

Figure 3-5 The Steering Wheel Is Jerky and You Have Tried the Set Controls Screens

that hold the steering wheel on the steering assembly. Tighten the screws to 50 + 8 inch-pounds. Connect the steering assembly harness to the simulator harness.

Attach the screw down tie wrap on the motor-opto harness to the cabinet, Make sure the wires will not be caught in the motor pulley. Connect the motor power harness to the motor amplifier PCB.

Install the back service door.

NOTE You must enter the self-test and go through the Set Controls screens because you repaired the steering PCB. Otherwise the simulator will not work correctly.

3-17

Page 52

Maintenance and Troubleshooting

Table 3-12 Torque Table for the Screws on the Steering Assembly

Replacing the Centering

Disk

The centering disk gives information to the centering PCB about the position of the steering wheel. ‘You should never have to replace the centering disk unless it has been bent or damaged through rough or careless handling. If the disk is bent and cannot be centered between the optical readers replace it immediately. If the disk is not bent, make sure the problem is the centering disk by following the troubleshooting table, Table 3-11 or a flowchart in Figure 3-3, 3-5, or 3-6.

Removing the Centering Disk

Turn off the power to the simulator.

  • Remove the three tamperproof screws and washers in the cover plate of the steering wheel. Take off the steering wheel and cover plate. See Figures 3-8 and 3-9.
  • Take off the back service door. Disconnect the steering assembly harness from the simulator harness. Disconnect the motor power from the motor amplifier PCB assembly. Remove the screw down tie wrap from the side of the cabinet. 4, Remove the four nuts that hold the steering assembly on the shelf. Push the screws through holes in the shelf. Remove the steering assembly.
  • Remove the belt on the front by pushing the motor towards the steering wheel mounting shaft and by working the belt off the pulleys.

3-18

  • Remove the pulley on the steering wheel shaft by loosening the socket-head screw that holds it on. (The socket-head screw has a penetrating adhesive on it.)
  • Take off the PCB bracket on the side of the frame by removing the two screws that hold it on the frame.
  • Remove the socket-head screw from the disk collar. Push the disk collar, the centering disk and the disk stiffening ring towards the front of the frame (away from the pulley and belt end) about an inch.
  • Loosen the two socket-head screws on the ball bearing.
  • Remove the one-inch retaining ring between the ball bearing and the centering disk. Push the shaft forward to reach the other retaining ring.
  • Remove the other one-inch retaining ring.
  • Push the shaft forward and pull the disk collar, centering disk, and disk stiffening ring off. 13, Remove the three socket-head screws and washers and take apart the disk collar, the centering disk and the disk stiffening ring.

Installing the Centering Disk

. Assemble the new centering disk with the disk collar. The slot in the disk should be 90° clockwise from the hole for the socket-head screw on the disk collar.

  • Assemble the disk collar, centering disk, and disk stiffening ring with the three socket-head screws and washers. Tighten the socket-head screws to 15 + 3 inch-pounds,
Page 53
  • Put the centering disk, collar, and stiffener on the steering wheel shaft. Make sure the socket-head screw hole is towards the front.
  • Install the one-inch retaining ring on the end of the shaft first. Then install the retaining ring between the ball bearing and the centering disk, Tighten the two socket-head screws on the ball bearing. 6, Make sure the disk collar is mounted on the shaft so the socket-head screw hole is over the flat on the shaft.
  • Install the centering PCB bracket on the side of the frame. Make sure the centering disk is between the optical readers and does not touch them. Tighten the screws on the bracket to 10 + 3 inch-pounds. uw

Steering wheel nas no teedoack during game play (although you car play the game) and you have aiready tried the SET CONTROLS soreen.

Teasure 8.

10.

fag

12, Maintenance and Troubleshooting

Tighten the screw in the disk collar to 30 + 5 inchpounds on the flat of the shaft to hold the disk in place. Put oil in the fill hole on the bronze bearing on the steering wheel mounting shaft if this has not been done recently. Take the socket-head screw out of the pulley and put a penetrating adhesive on it. Slide the pulley on the back of the steering wheel shaft. Align this pulley to the other one. Install the socket-head screw so it is on the flat of the shaft. Tighten the screw to 50 + 8 inch-pounds. . Install the belt by pushing the motor towards the steering wheel mounting shaft and working the belt oato the pulleys. Before you install the steering assembly back in the simulator, turn the centering disk so the single hole

CONTROL INPUTS screen, ‘does the weel postion no. increase smoothly as you um the wheel clock- ‘te? Does the ooston no. become zere once eve the vatage onthe ‘wo stering whee! postion inputs ‘on the main PCB. Does the ingut ‘change continuousy trom 0 0 1 ad ack wren you turn the steesng wneet? Check steering wheel hamess. Check steering wheel encoder and centering isk and PCBs.

Ld

Go to the MAIN BOARD CON/ROLS screen and choose the STEERING WHEEL item ‘Choose the SEND FORCE Test from the submenu, Troubleshoot the optical poston circuit cn the main 2CB. See the main PCB schematic, Troubiestool the Motor Amp PCB.

Do you get the proper force on the steering wheel?

Troubleshoot the optical position circuit ‘on the main PCB. Sea the main PCS schematic, Cheok the resistance to the motor when itts cold. The resistance should be between Gand 12 . Is the resistance toc high or too law?

Replace metor.

Figure 3-6 The Steering Wheel Has No Feedback and You Have Tried the Set Controls Screens

Page 54

Maintenance and Troubleshooting

in the disk is between the optical readers on the PCB. This will make it much easier to correctly install the steering wheel.

  • Put the steering assembly back in the cabinet. Install the four carriage bolts through the holes in the shelf. Tightly install the fender washers and nuts on the bolts so the assembly does not move.
  • Install the steering wheel with the center spoke down. Make sure the single hole on the centering disk is between the optical reader on the centering PCB so the steering wheel will be correctly centered. Put the center cover on the steering wheel. Install the three tamperproof screws and lock washers that hold the steering wheel on the steering assembly. Tighten the screws to 50 + 8 inch-pounds.
  • Connect the steering assembly harness to the simujator harness. Attach the screw down tie wrap on the motos-opto. harness to the cabinet. Make sure the wires will not be caught in the motor pulley. Connect the motor power harness to the motor amplifier PCB.
  • Install the back sesvice door.
NOTE You must enter the self-test and go through the Set Controls screens because you repaired the steering assembly. Otherwise the simulator wili not work correctly.

: :

Replacing the Encoder Disk

The enceder disk gives speed and direction information about the steering wheel movement to the encoder PCB. You should never have to replace the encoder disk unless it has been bent or damaged through rough or careless handling of the steering assembly. If the disk is bent and cannot be centered between the optical readers, replace it immediately. If the disk is not bent, make sure the problem is the encoder disk by following the troubleshooting table, Table 3-11 or the flowchart in Figure 3-3, 3-5, or 3-6. To replace the encoder disk, do the following:

Removing the Encoder Disk

  • Turn off the power to the simulator. 2, Remove the three tamperproof screws and washers in the cover plate of the steering wheel. Take off the steering wheel and cover plate, See Figures 3-8 and 3-9.
  • Take off the back service door. Disconnect the steering assembly harness from the simulator har-

3-20 ness, Disconnect the motor power from the motor amplifier PCB assembly. Remove the screw down tie wrap from the side of the cabinet. Remove the four nuts that hold the steering assembly on the shelf. Push the screws through holes in the shelf. Remove the steering assembly. a

  • Remove the harness from the encoder PCB over the encoder disk. Take off the two screws that hold the encoder PCB on the assembly. Remove the PCB.
  • Loosen the socket-head screw from the encoder disk collar. Take off the disk collar, the encoder disk and the disk stiffening ring, which are held together with three socket-head screws. Remove the three socket-head screws and washers and take apart the disk collar, the encoder disk and the disk stiffening ring.

Installing the Encoder Disk

. Replace the encoder disk. Assemble the disk collar, encoder disk, and disk stiffening ring with the

three socket-head screws and washers. Tighten the

screws to 15 + 3 inch-pounds.

  • Put the encoder disk, collar, and stiffener on the motor shaft. Make sure the hole for the sockethead screw faces out and is over the flat of the shaft.
  • Put on the encoder PCB so the optical readers and the harness connection face down. Move the encoder disk so ii is between the two readers, but does not touch them. Tighten the screws on the encoder PCB to 10 + 3 inch-pounds.
  • Tighten the screw in the disk collar to 30 + 5 inchpounds to hold the disk in place. Make sure the encoder disk still does not touch the optical readers,
  • Install the harness on the encoder PCB.
  • Put oil in the fill hole on the bearing on the steering wheel mounting shaft if this has not been done recently.
  • Before you install the steering assembly back in the simulator, turn the centering disk so the single hole in the disk is between the optical readers on the PCB. This will make it much easier to correctly install the steering wheel.
  • Put the steering assembly back in the cabinet. Install the four carriage bolts through the holes in the shelf. Tightly instali the fender washers and nuts on the bolts so the assembly does not move.
Page 55
  • Install the steering wheel with the center spoke down. Make sure the single hole on the centering disk is between the optical reader on the centering PCB so the steering wheel will be correctly centered, Put the center cover on the steering wheel. Install the three tamperproof screws and lock washers that hold the steering wheel on the steering assembly. Tighten the screws to 50 + 8 inch-pounds.
  • Connect the steering assembly harness to the simulator harness. Attach the screw down tie wrap on the motor-opto harness to the cabinet. Make sure the wires will not be caught in the motor pulley. Connect the motor power harness to the motor amplifier PCB.
  • Install the back service door.
NOTE You must enter the se/f-test and go through the Set Controls screens because you repaired the steering assembly. Otherwise the simuiator will not work correctly.

Video Display

If you have probiems with the video display, check Table 3-11, Troubleshooting the Video Display, before you remove the display.

Adjusting the Video Display

To make adjustments to the video display, open the top service door on the top of the cabinet.

Removing the Video Display

Perform the following procedure to remove the video display. (See Figure 4-1.) 1, Turn the simulator power off and wait two minutes, Leave the power cord plugged in.

  • While you wait, unlock the top service door on the top of the cabinet. Remove the ground wire that is clipped to the display chassis.
  • Remove the six washers and tamperproof screws in the bottom attraction retainer, and take off the bottom attraction retainer, Remove the three washers and hex-head screws in the top attraction retainer and also take this retainer off. Remove the attraction decal and shield. Maintenance and Troubleshooting
WARNING High Voltage The video display contains /ethal high voltages. To avoid injury, do not service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display is designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode jf struck or dropped. The shattered glass from the tube may Cause injury up to six feet away. Use care when handling the display.

10. . Take off the board with the fluorescent light mounted on it, Disconnect the light harness from the simulator harness. . Open the back service door. Loosen the nuts on the carriage bolts in the front of the dashboard. You may have to loosen nuts on the other bolts that hold the dashboard in place or may even have to remove the dashboard to remove the video display shield and bezel. . After you remove the video display shield and bezel, take out the screws that hold the right and left video display shield wood brackets in place. Remove the wood brackets. . Remove the screws that hold the boitom attraction retainer in the cabinet, and take out the retainer. . Discharge the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Attach one end of a solid i8-gauge wire to a well-insulated screwdriver or wooden handle. b.Attach the other end of the wire to an earth ground. c. Quickly touch the biade end of the screwdriver to the CRT anode by sliding it under the anode

d. Wait two minutes and repeat part c. . Disconnect the harness connectors from the video display. Remove the screws that hold the video display assembly on the video display mounting brackets. The front screws have a flat washer, lock washer and a nut on them. The rear screws have only a washer and no nut.

3-21

Page 56

Maintenance and Troubleshooting

Table 3-13 Troubleshooting the Video Display Problem Solution « Any problem.

Convergence, purity or color problems. . self-test. «se Determine if the problem is with the displ ~ by performing the self-test. If you cannot pe: . DIP switch diagnostics to narrow, down. Check the voltage level to the vi Check the video display settings with the.

  • Pull the video display assembly out of the cabinet. Be extremely careful.
WARNING When you take the video display out of the cabinet, do not drop it! The display is heavy. Be careful! Wear gloves to protect your hands from the sheet-metal edges.

Replacing the Video Display

Perform the following procedure to replace the video display in the cabinet. (See Figure 4-1.)

NOTE If you replace the entire video display or the yoke, reverse the wires on the vertical winding before installing the display in the cabinet.
  • Carefully lift the video display into the cabinet.
  • Install the screws that hold the video display assembly on the video display mounting brackets. Put a flat washer, lock washer and a nut on the front screws. The rear screws have only a washer.
  • Connect the power and signal harnesses to the video display. 4, Install the bottom attraction retainer with the tamperproof screws. Replace the right and left video display shield brackets.
  • Install the video display shield and bezel. Replace the dashboard if you removed it. Tighten all the nuts on the carriage bolts that hold the dashboard in place.
  • Connect the light harness to the simulator harness. Install the board with the fluorescent light mounted on it.
NOTE Be sure to clip the ground wire to the new display chassis.
  • Install the attraction decal and shield. Install the top attraction retainer with the three hex-head screws.
NOTE When you replace the cathode-ray tube and yoke together, adjust the brightness, size, and centering as described in the video display service manual. Check the purity and convergence according to the service manual instructions, but adjust both only if required.
  • Lock the top service door on the top of the cabinet.

3-22

Page 57

CHAPTER 4

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware parts, such as screws, nuts, washers, and so on usually are not listed in the parts lists.

The parts lists (except for the PCB parts lists) are arranged alphanumerically by Atari part number. All A-prefix numbers, which are assemblies, come first. Next are part numbers with six numbers followed by a hyphen (XXXXXX-XX). Ending the list are part numbers with a two-number designation followed by a hyphen (XX-). The PCB parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by part number. When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari Games Customer Service phone numbers are listed on the inside front cover of this manual.

Page 58

Ilustrated Parts Lists

046570-01 139022-202 25" Sid. Res. Video Display Monitor Dampener 701-248

(2 places)14-20 LocknutTS045S
048491.01CaBSTI(places)1 Spock Waser
comming]HenSasatcarene:asi,le
oreo+196010-001HexHa,14" Flat Washer
Lamp BracketContact Cement AdhesiveBiseen™(t2places)
7‘AltactRetainer1"Hex

irae ‘76263-0402 "| Ski. Screw action Ste Ua" Foam Tape | (3 places) ston Bee 76014-3040 ‘Atvaston Decal fc Fat Washer 046579-01 046600-01 places)

vpEYonealpataa,(See

A ‘@ places)

046817.01AeMonitor & Atract Retainer
Let tract CleatBae2048849-01j

46617-02 Genter Retainer Decal Fight Atvact Cleat ‘75014-3040 76020-229| #10 Fiat Washer soxt ex (places) x1 8" xRee Seren roost 36 reonoe9 Hodes tampee ox1 ue PW cron Foal Su Hd, Seow places) 263-0402 o4ss49.01 'W.x 118 Thk, Foam Tape Center Retainer Decal o46625-01 Video Display & 046615-01, Niet ain paces) 476015-110 eaonee 0x si Pant, Scrow +#10-32 x 1/2" Flat-Hd. Screw (8 places) (places)

046528-01 Video Display Boze! 946625.01 Front Sez 0ae619-02 4007-003 \ | Monier Bracket Speaker 75-0159, (2 places) 14" pit Lack Whe 176015-\12 “Plzces) aro a1d" Pane sFroog-8e Hd, Scrow 14:20 Hex Nut (Gplaces) ‘@ places) 75014-1050 vat Fat Washer (places)

  • 75.8520, 096627-01 h2oxt 8" Video Display Stietd Cariage Bolt 6 @ places) 12 stoning Wee 4, i) (046459-01 oss Steering Wheel Decal D eee 046655-01, Mirror Retainer Seeing nel Covet Pate places) 1750143050 176020-208
‘va Bat Washerzossaali332" PW Seow

weet) wrt paces 118-20 +" Tamper Prod Seren 75.0858 Yew x18" Tk Foam Tape

famper-ProglSciow'|4" Spli-Lock Washeres

7507002 1V8" Fonder Washer

7555208apassat-o1— hajustabie cide

1¥4-20 x1 114 Cartage Bat | ControiPanel Assy, places) 1086642.01 75,5528B) Steering FEB PUley Assy. “14-20. 1318" Carriage Bott 75014-3050 (places) 114 Pat wash 75.055 (é places) 114" Internal Tooth Washer crert 048846.01 (4places) seed Locinat Seat Book Decal

Tae ee(8 places)‘n046916-01
Foam TapeauraSee Sake Peta sy.
7+14" Push-on SpringNut|ait
va" Fender Washor‘Binttoas)ansenieos‘a-20 x 1" Bin-Hd, Sorew
(S places)17024-0144Clutch Pedal Sssy.(2places)
1790441050 |174-20 Low-Crown Bik Nut1750143050176025-4116
‘a Fat aie‘4 places)sua" Fat Washer114-20 x 1" But Hd, Tamper-Proo! Screw
@plnces!(4 places)@ places)

5285168 {75014-3050 #8 Bik X-Rec Screw Ua" Fat Washor 176025-8116 (places) 1420.1" Bur. Tampor Prot Srey places)

Figure 4-1 Cabinet-Mounted Assemblies, Front View A048840-01 B

Page 59

Illustrated Parts Lists

NOTE: Steering Assembly Is rotated for clarity. 04994201 ee ‘Cabinet Assy.

A046642.01 , 1g Assy. 048845-02 Stootng Assy 21 Decal " Right Side Pane! Dec: : 142028001 “Ua Fender Washer GO0Hz Baliast Transformer ~~) 17010-2446 7ossi816P Locknut Wire Nut (places) #0 x 18" Pan-Hd, Screw Motor Amp PCB Assy.

Potces)|‘ratan-soe

oth S (enieoos)

ve care Es\|ossass.o1
~.iRibbon Cable Motor Assy.

| 046679-01 Hi Power Supply Assy.

4.|{76015-112

NI HO x314" Pants, Screw ‘A046901-04 (2 places) Mulisyne PCB Assy. 725116 1027001 oats Hoxts Seren Goin Door 75-0408 s76015-112 “Leck We #0314" Pen-Ha, Screw Gab Soke ack Washer Te-eHo02 | o46596-01 Floor Mat Back Service Door a Decal 476015-112 Service Dsor 0 Ree Seren <—__ 620.220 fas Ue Lew Seow x048864.01 paces) Face Divi Compact . ‘sr351 Board Set Assy. ‘Solt-Test Label sound PS Ay, posasi0.1 is ‘Orv Switch Assy. ‘A04S889-01 y ADSP PCB Assy 176015-110 y. #0 x 5/8" Pan-Hd. Screw +175008-706 aoxee Fiber Washor (2 places} 175004-708, Fer Washor items Not Shown: (2 places)

178033-1610-8046396-01176015-112177000-144086620.01
6x 5/8" Pan-H. ScrewMotor Ripoon Cable Assy,#10 3/4" Pan-He. Screw114-20 Hex NutLeft Foor Trim
(2 places)Anss6s0-01(2places)2 places)176015-112
A76015-112Main Harness Assy.A046341-01175014-1050#10 x 3/4" Pan-Hd. Screw
‘#10 x 3/4" Pan-Hd. Screw:Coin Counter Assy,1/4" Flat Washer(5 places)
TaniAs11906-1038,(2 places)0411008
‘ealAudio Potentiometer‘78-5520BLight Starter Sckt
noteseagyaaen118-20 x14 Cartage Bot pons

5 places) 3

‘ansessnorvote Sac(places)Up seer
Video Harness Assy.160088-00:here
178126-002Auxillary Soin Credit Switen Lett Seat DecalSocpact Race Diver ‘Schematic Package
Camper Froct Hex Key Divan ineeUnk DecalGompact Face Drivin’ Salt-Test Lael

i 048845.01 y

Lat Monitor Bracketplaces)Lok'Side Panel Decalonsact Race Drv Operators Maral
noss340.01Te 085S oswaher(70a 200sesso
Component Bracket Assy.74 Splitock Washergg114" LPW Serew_Well-Gardner 25" St-Res. Video Display Manual
Ansige seat). Pars:(2placas)fanaces)

Figure 4-1 Cabinet-Mounted Assemblies, Rear View A048840-01 B

Page 60

Illustrated Parts Lists

4-4 Items Not Shown: A046666-01 Start Hamess Assy A046667-01 Shitter Harness Assy A046668-01 Abort Harness Assy

75-55288 Caniage Bot

160052-001 Pushbutton Switch 036895-01 Switch Bezel

046655-01 ‘Steering Wheel Center Cover

046459-01 Steering Whee! Decat

75.0558 Lock Washer 176025-4416 Tampor-proof Sorew Bik Flat Washer 47024-0144 Low Crown Nut

046621-01 Control Panel ms \ 17014-3050 i

046682-01 ‘75-5520B Control Panel Decal | 1/4" Bik Carriage Bolt 17012-4111 Spring Nut 75-07002 Fender Washer 17010-2484 Locknut

‘4047000-01 Key Switch Assy. 7551128 18" Carriage Bolt 17010-240 #10-24 Hex Locknut

‘A049936-06 Shifter Assy. 005255-06 Shift Bezel 039154.01 Shitter Spacer 75-5124B| 7555208 ‘ #1024 x1 1/2" i packited 1/4" Blk Carriage Bolt —| __ 175014-1043 | 178089-005 Flat Washer Steering Wreet 477010-240 Locknut

Figure 4-2 Dashboard Assembly A046567-01 D

Page 61

N Illustrated Parts Lists

S

Page 62

Illustrated Parts Lists

72-5432 318-16 x 2" 1750141070 Hex Bolt 177010-248 2/8 Lock Nut \ 7/16 Fit Wshr

041787-02 106007-001 Encoder Disk Adhesive

046650-02 Encoder Disk Collar

Pivot Plate

#8 Skt-Hd Screw 75-0488 #8 Split-Lock Wshr 175014-1032 #8 Fit Wshr

  • fs oe a

72-5416 Items Not Shown: Hex Bol 72-8406 4#4-40 Sckt-Hd Screw 75-0448 #4 Split-Lck Wshr

046644-01 Strg Whi Mnitg Shaft Steering Wheel and Mounting Hardware: 176022-3806 #8-32 Skt-Hd Screw

Steering Wh! Decal (046655-01 Steering Whl Center Cover 176025-4416 1/4-20 Blk Tamperproot Screw 178099-005 Steering Whee! ‘75-055B 1/4 Bik Lock Wshr 046650-01 Centering Disk 175014-1063 177010-248 3/8 Fit Wshr 3/8 Lock Nut / 178012-010 1” Clip Ring

178268-001 Ball Bearing

046647-01 PCB Mtg Brkt

72-CT604 #6-32 Hex Wshr Hd Screw

‘A046691-01 Centering Disk Collar PCB Assy

043807-02 Centering Disk

Figure 4-3 Steering Assembly, Front View A046642-01 D

4-6

Page 63

Race Drivin’ Compact Illustrated Parts Lists

107013-001 Oil 178269-001 Bronze Bearing

107013-001 oil ‘A046665-01 . Motor-Opto we Hamess Assy 046648-01 ae 72-CT604 Disk Stiffening a #6-32 Hex Wshr Hd Sorew

A046689-01 Encoder Disk PCB Assy

106007-001 Penetrating Adhesive

178270-002 6" Pulley

72-5416 9/8-16 x 1" Hex Bolt 17827-1046 Pulley V-Belt : oar Motor Assy

175014-1077 1/2 Flat Wshr | 178012-006 016545-01 112" Cip Ring Pivot Shaft 78270-0038 2" Pulley

Figure 4-3 Steering Assembly, Rear View A046642-01 D

Page 64

Illustrated Parts Lists Race Drivin’ Compact

75-5124B #10-24 Bik Carriage Bolt 178027-001 Lithium Lubricant 005255-02 a Shifter Bezel

039154-01 Shifter Spacer NN

A000610-02 Handle Assy

039705-01 Compression Spring

178219-001 3/8" Ball

177010-240 e.00 #10-24 Locknut onoeoeia 175014-1043 Flat Washer

000611-02 H-Pattern Detent 043711-01 Return Spring rsraot

  • 177010-232 72489608 4-40 Hex Nut ee Wshr-Hd Screw Switch 7214128 049712-01 #4-40 X-Rec Screw ‘Switch Spacer

Figure 4-4 Shifter Assembly A043936-06 A

Page 65

046450-01 176008-110 4 107029-001 ‘Actuator #10 Sckt-Hd Screw Lithium Grease 75-0408

#10 Split- 175009-364 Lock Wshr Nylon Washer

sott-ooa 178256-001 178001- Spring 1/2" Retaining Ring 178001-004 1/2" Retaining

160045-003 Switch

NOTE The switch is installed in the 046999-01 game rotated 180° from the Housing position shown here.

177010-232 #4 Hex Locknut 7214128 +#4-40 Screw 75-0145 #4 Flat Wshr

Figure 4-5 Key Switch Assembly A047000-01 A Illustrated Parts Lists

Items Not Shown: 172020-0814 Spring Pin

Page 66

Illustrated Parts Lists

Details of transparent side panels below

72-8810 #8 Skt-Hd Screw 177000-138 #8 Hex Nut

99-215008 72-8810

¢Install two screwsInstall two screws

bite fifa through the bumpers | through the bumpers

107027-001ed7into these holes,into these holes

Lithium Grease boned Lower Link 1700-138 #8 Hex Nut

99-215009 Right-Wound Left-Wound Spring Brake side panel Gas side panel

047210-01 Upper Link 047217-01 Bumper Sleeve 047218-01 val 11908-1001

Rubber Bumper|:7Potentiometer

‘A047085-01 Brake Pedal Replacement Kit Assy

82-8516B Button Hd Screw 175014-3050 Flat Bik Wshr

NOTE When links, set the upper link 22° clockwise from vertical. All parts not called out in this illustration are part of the Front and Sides Assembly, reassembling the

part number 171092-001.

176012-220 99-215006 176025-4416 Wood Screw Gas Pedal Tamperproof Screw 175014-3050, Flat Bik Wshr

Items Not Shown: A046669-01 Gas Harness Assy

Figure 4-6 Brake and Gas Pedal Assembly A046916-01 B

Page 67

Race Drivin’ Compact Illustrated Parts Lists

4 107027-001 Lithium Grease

install two screws through the bumpers 047210-01 Upper Link 175012-0125 177000-138 Flat Washer 047211-01 #8 Hex Nut into these holes Ae Lower Link 72-6610 177000-138 #8-32 Sckt- 149008-1001 #8 Hex Nut Potentiometer 99-215009 72-8810 Left-Wound #8-32 Sokt-Hd Screw

Detail of transparent clutch side panel below

176025-4416 ‘Tamperproof Screw 175014-3050 Flat Bik Wshr

99-215006

NOTE Clutch Pedal All parts not called out in this illustration are part of the Front and Sides Assembly, part number 171092-001.

82-8516B Button Hd Screw 175014-3050 Fit Blk Wshr

Item Not Shown: ‘A046671-01 Clutch Harness Assy

Figure 4-7 Clutch Pedal Assembly A046915-01 B

Page 68

Illustrated Parts Lists Race Drivin’ Compact

99-1513 Key Hook

75-9448 Locknut

99-10152 Right Coin inlet

171006-035 25 Cent NORYL Acceptor

99-10104 AP.F. Bar Keoper|

99-10105 99-10154 | APF. Bar ‘Switch & C.R.EM. Bracket

‘99-10075 thru 99-10078 ‘Switch Wires,

99-10150 ‘Switch Cover

'98-10042 thru 99-10045 Coin Switch Assy.

Figure 4-8 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

4-12

Page 69

99-10161 | Side Entry Button Asay. 99-10158, 99-10160 Coin Inlet, Illustrated Parts Lists

99-0117 Coin Return Door

Coin Door

99-10149 Service Door 99-10169 1.0. Labeil

99-10143} Die Cast Frame T2HA1404C Frame Hinge Screw| Bezel! , Button Cover 99-10159 199-10141 Coin Retumn Bezel 26 Cent Decal 99-1013 Token Decal!

99-1015, Spring for Button

99-10744 Slide Mounting Clip

99-10170 | Frame Clamp Screw

99-10166 4 7/8" Flat Key Lock

NOTE The acceptable substitute for this door (and the one used in games manufactured in Ireland) is the Coin Controls Ltd. Coin Door Assy., part no. 171034-001. You can obtain a tree Coin Controls Ltd. supplement (part no. CO-305-01) that has illustrations and a parts list. Write to Atari Games Ireland Limited, Tipperary Town, ireland. Telephone 062-52155. 99-10167 Cam Lock

Figure 4-8 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A

4-13

Page 70

Mlustrated Parts Lists

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description Part No. Description

160057-001Coin Switch99-10081Key Holder
70-11-47Miniature Bayonet Lamp99-10096Fastener
72-9406S#4-4) x 3/8-Inch Truss-Head Screw99-10104Bar Retainer
72-HA1404C_#4-40 x 1/4-Inch Pan-Head Screw99-10105Bar
72JA1405B-#4-40 x .31-Inch Pan-Head Screw99-10115Spring
75-14128#4-40 x 3/4-Inch Pan-Head Screw99-10116Plastic Coin Return Lever
75-9948#4-40 Locknut99-10117Steel Coin Return Door
99-10008Retainer99-10139Coin Door
99-10042Coin Switch Assembly for Belgian 5 Fr and99-10140Coin Door Inner-Panel Assembly
US. 25¢99-10141Die-Cast Coin Return Cover
99-10043Coin Switch Assembly for German 1 DM,99-10143Coin Door Frame
Japanese 100 Yen, Swiss 1 Fr99-10144Channel Clip

99-10044 Coin Switch Assembly for German 2 DM, Ital-

ian 100 L, U.S. $1.0099-10147Hamess
99-10045,Coin Switch Assembly for Australian $.20, Ger-99-10148Lock Assembly
man 5 DM, British 10 P99-10149Service Door

99-10150 Switch Cover 99-10068 Coin Return Chute

99-10075Switch Wire (included in coin switch assembly99-10151Left Coin Inlet
99-1043)99-10152Right Coin inlet
99-10076Switch Wire (included in coin switch assembly99-10153Coin Return Box
99-10042)99-10154Bracket Assembly

99-1007 Switch Wire (included in coin switch assembly

99-10044)99-101601-Inch Wide Die-Cast Coin Inlet Housing
99-10078Switch Wire (included in coin switch assembly99-1016125¢ Amber Side-Entry Coin Button Assembly
99-10045)99-15066Screw for Clamp
99-10080Lamp Socket171006-035Metal Coin Mechanism for U.S. 25¢
Page 71

Race Drivin’ Compact Ilustrated Parts Lists

179231002 AQ46346-02 A046346-01 149005-002 2-Position 1S" Wht 18"Bik —_A043367-01 ‘Switching Power Suppiy Terminal Block Jumper Assy Jumper Assy Jumper Assy

A042384-01 Line Fitter Assy

179225-2205 5-Position Fuse Block 034544-01 Fuse Block Cover

146008-3022 3 Amp, 250V Fuse

14608-2022 APU PCB 2 Amp, 250V 142051-001 Assy Fuse Transformer

Figure 4-9 Power Supply Assembly A046673-01 A

4-15

Page 72

Illustrated Parts Lists

Power Supply Assembly Parts List

Part No.DescriptionPart No.Description

A042384-01 _ Line Filter Assembly 146008-2022 2 Amp, 250V Slow Blow Fuse

‘A043367-01Jumper Assembly14608-3022 3 Amp, 250V Slow Blow Fuse
‘A044431-02“APU PCB Assembly (See Figure 4-11)149005-0025 Volt, 15 Amp Hitron Switching Power
‘A046346-0115-Inch Black Jumper AssemblySupply Gee Below)
A046346-0215-Inch White Jumper Assembly179225-2205 5 Position Fuse Block
034544-01Fuse Block Cover1792310022 Position Terminal Block

142051-001 Transformer

Hitron 5 Volt, 15 Amp Power Supply Sub-Assembly Parts List

Part No.DescriptionPart No.Description
‘Transistors99-211026Resistor, Carbon Film, 330 Ohm, 5%, 1/4W
2ti002TyatisitoeeNPNS25C14199-211027Resistor, Carbon Film, 5.6 Ohm, 5%, 1/4W
ap aiitosTansee NPN, FESSOR99-211028Resistor, Carbon Film, 8.2 Ohm, 5%, 1/4W
99-211004Transistor, PND, PE8S50B99-211029Resistor, Carbon Film, 10 Ohm, 5%, 1/4W

-211062 Transistor, 28D72!

atlqa ae eeecoon99211030Resistor, Carbon Film, 39 Ohm, 5%, 1/4W
*99-211031Resistor, Carbon Film, 56 Ohm, 5%, 1/4W
Diodes99-211032Resistor, Carbon Film, 1K Ohm, 5%, 1/4W
2110;Resistor,Metal Film,2K Ohm, 2%, 1/4W
99-211005Diode, Schottky, $10SC4Maie?esistor,MetalFilmana
99-211006Diode, Fast Recovery, 30DF199-211034Resistor, Carbon Film, 180K Ohm, 5%, 1W
99-211007Diode, Zener, IN752A99-211035Resistor, Carbon Film, 2K Ohm, 5%, 1/4W
99-211008Diode, Rectifier, 1N400699-211065Resistor, Wire Wound, 27 Ohm, 5%, 2W
.99-211066Resistor, Carbon Film, 6.8 Ohm, 5%, 1/2W

99-21:1009 Diode, Fast Recovery, Rpgl0B

99-211010Diode, Fast Recovery, Rpgl0K99-211067Resistor, Carbon Film, 12 Ohm, 5%, 1/4W
99-211011Diode, Fast Recovery, Rpgi5B99-211068Resistor Carbon Film, 2.4 Ohm, 5%, 1/2W
99-211012Diode, Switching, 1N414899-211077Resistor, 470 Ohm, 1/2W, 5%
-2111i12IW, 5%
99-211064Diode, $15SC4MiaResistor120% Ohm,17258
99-211076Diode, 31DQ04Capacitors

-21101 Rectifier, Sili led,

-3petines, Sioa Comune 2280099-211036Capacitor, Metal Film, 0.047 HF, 250V
Resistors99-211037Capacitor, Metal Film, 0.22 UF, 100V

99-211038 Capacitor, Metal Film, 0.1 LF, 400V

99-211014Potentiometer, Trimming, 3K Ohm-2110:ital Film,0.022 LF, 100V
99-211015Resistor, Wire Wound, 50 Ohm, 5%, 2W99211039Capacitor, MetalFilm,Me,
99-211016Resistor, Wire Wound, 150 Ohm, 5%, 2W99211040Capacitor, Ceramic, 1800 PE, 2KV. Z5V
99-211017Resistor, Wire Wound, 33 Ohm, 5%, 2W99-211041Capacitor, Ceramic, 0.01 KF, IKV, 25U
-211042Capacitor, Ceramic, 0.001JF, 2KV
99-211018Resistor, Wire Wound, 0.47 Ohm, 5%, 2WeenCpscice Ceramic. 470 paieas 75P
99-211019Resistor, Wire Wound, 120 Ohm, 5%, 2W’°a
29211020Thermistor, 0.5 Ohm, 5%, 5W99-211044Capacitor, Electrolytic, 470 UF, 25V
99-211021Resistor, 2.2K Ohm, 2%, 1/4W99-211045Capacitor, Electrolytic, 220 uF, 25V
99-211046Capacitor, Electrolytic, 100(UF, 200V
99-211022Resistor, Carbon Film, 330 Ohm, 5%, 1/2W9.211047Capacitor Hleauohnic 00025
99-211023Resistor, Carbon Film, 270 Ohm, 5%, 1/2W,,,
99-211024Resistor, Carbon Film, 470 Ohm, 5%, 1/4W99211048Capacitor, Electrolytic, 2200 UF, 16V
99-211025Resistor, Carbon Film, 47 Ohm, 5%, 1/4W99-211049Capacitor, Ceramic, 4700 UF. 400V

4-16

Page 73

Illustrated Parts Lists

Hitron 5 Volt, 15 Amp Power Supply Sub-Assembly Parts List

Part No. Description Part No. Description _

99-211069Capacitor, Electrolytic, 2200 HF, 16V99-211088Inductor, 60 MH

99-211070 Capacitor, Electrolytic, 220 WF, 25V 99-211079 Capacitor, De7100F22M Transformers

99-211080Capacitor, 1000 pF, 35V99-211075‘Transformer, Power

; 99-211083 Transformer, Power

99-211081Capacitor, 470 UF, 25V99-211089Transformer, 4.75 MH
99-211082Capacitor, 220 UF, 16V99-211092Transformer
99-211090Capacitor, Ceramic, 1000 PF, 2KV.99-211055Transformer

99-211091 Capacitor, Electrolytic, 2200 UF, 10V Miscellaneous Inductors 99-211001 Regulator, UA431AWC

99-211050Inductor, 7 HH99-211056Fuse, 2A, 250V
99-211051Inductor, 7 HH, 35MM.99-211057Terminal Block, 8CKT
99-211052Inductor, 15MH99-211058Fuse, 2A, 250V, Semko

99-211053, Inductor, 1.5MH 99-211059 Heatsink

99-211054Inductor, 2.2 WH99-211060Fuse Holder, 6.35MM
99-211071Inductor, 9.8 Hi99-211061Heatsink, 1.5MM
99-211084Inductor, 8 HH99-211072Fuse Holder, 5.2X20

99-211085 Inductor, 9.8 WH 99-211073 Fuse, 2A, 125V

99-211086Inductor, 0.75MH99-211074Terminal Block, 9CKT

99-211087 Inductor, 2.2 WH

4-17

Page 74

4-18 Figure 4-10 Race Drivin’ Compact Multisync PCB Assembly A046901-04 B is 8 is s eT sous irom

~* Stare, Haag ie dere ag)

437199-002 Boy wer 0S aT 137199-02 p= 20: i) £0) 1g02 ss) ol

30x El

eee ee

SP says Spa 137199-002 ] {02s} ae §

ose 40 MISO

tass73 puss74

i = ] $C r spp prs

i op 4137993-002 q B 437593-007 op dog of 30 40 50

Ne A908 Os] sarsoa-o02 om job 137553-002 7 137553-00: ik Roses

Tse

137553-002 oe lof

ease sme] 137553-902 &

137s53-002 EQS “mn

Ser ford 1380S ame shiz b

OSes] S es eee ° of oe. 08 oy uate

z 14 $051) 805 a 7)

8573 ri ge 12805 sa] Reggae)

1205“

soo 2, 88573 ] S805" seo FR fs32 & goss] Ogos] ee _ OD i

p= ros pore p59 g LP g

got] o $00]

Ls74 a 5 aa7ssa-o01 S06 u

Lee] a LST Boe Fe 530:

We Ha

437538-002 =

Pa

‘OSL aw sory smog foe

4 g g sorts ox Saw Josten) Lsare pooh B aes Fou, Lsz0 £09 58] we Freceeee]

Ausi36 Lay

305s ]g05 ee) 809s San

SP

160 170 18! “=e J

K L 32 Md| apcAtSten S05n an] = Ls2ugre Ls24s,

sae

905s] ] 05s —] £0: TH Ausi39 i 205 ame] gos 8

Asoo ; op, 45388 g022e] §0 21%)

g Sosa GEE) gosta zB coc CH HO BD

i x s z SS fog {og fog fog naw 0g of

by a a: 40, fos ausi98 (to ¢08

sm Ls2us P [#208 om sews (one 203 an a TaraN-00e a [x30 B32 Staaraxz-317 Ls2uy (08 uszw (sa 20 Hs ‘08 Ls2us, ay 137580-150 i 197942-150 137535-00% Illustrated Parts Lists

Page 75

Race Drivin’ Compact Illustrated Parts Lists

Race Drivin’ Compact Multisync PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
Integrated CircuitsJOYIntegrated Circuit, 74AS08137484-001
SKIntegrated Circuit, 4464, 64K x 4,137546-00375CIntegrated Circuit, 74L$259137137-001
DRAM75HIntegrated Circuit, 741814137056-001
5MIntegrated Circuit, 74F244137502-00180MIntegrated Circuit, 74ALS138137517-001
15BIntegrated Circuit, AD711KN137614-001
15KIntegrated Circuit, 4464, 64K X 4,137546-003ascIntegrated Circuit, 7418374137144-001
DRAM85P, 85SIntegrated Circuit, VRAM, 64Kx4,137553-002

150 nsec (Acceptable substitute is part

15MIntegrated Circuit, 74ALS245137440-001no. 137553-001, Integrated Circuit,
20PIntegrated Circuit, 74ALS574137548-001VRAM, 64Kx4, 120 nsec.)
20S, 20U Integrated Circuit, 74BCT29823137513-00385U, 85W Integrated Circuit, VRAM, 64Kx4,137553-002
20WwIntegrated Circuit, 74BCT29823137513-003150 nsec (Acceptable substitute is part

no. 137553-001, integrated Circuit,

25KIntegrated Circuit, 4464, 64K x 4,137546-003,VRAM, 64Kx4, 120 nsec.)
DRAM90MIntegrated Circuit, 74ALS08137460-001
25MIntegrated Circuit, 7448573137547-001
30BIntegrated Circuit, 7418374137144-00195CIntegrated Circuit, 7418374137144-001
30PIntegrated Circuit, 74LS245137134-00195P, 95SIntegrated Circuit, VRAM, 64Kx4,137553-002

150 nsec (Acceptable substitute is part

30S, 30U Integrated Circuit, 2149, 45 nsec137199-002no. 137553-001, Integrated Circuit,
30WIntegrated Circuit, 2149, 45 nsec137199-002VRAM, 64Kx4, 120 nsec.)
30YIntegrated Circuit, 7418245137134-06195U, 95W Integrated Circuit, VRAM, 64Kx4,137553-002
35KIntegrated Circuit, 4464, 64K x 4,137546-003150 nsec (Acceptable substitute is part

DRAM no. 137553-001, Integrated Circuit, VRAM, 64Kx4, 120 nsec.)

35M.Integrated Circuit, 74ALS245137440-001100MIntegrated Circuit, 74415161137470-001
40HIntegrated Circuit, 74L$123137268-001
40S, 40U Integrated Circuit, 2149, 45 nsec137199-002i10¢Integrated Circuit, 7406137052-001
40wIntegrated Circuit, 2149, 45 nsec137199-002110KIntegrated Circuit, 74ALS138137517-001
120HIntegrated Circuit, 74F74137436-001
40YIntegrated Circuit, 7418245137134-001120KIntegrated Circuit, 7418393137146-001
45BIntegrated Circuit, ADCO809137243-001
50HIntegrated Circuit, 74L$123137268-001120MIntegrated Circuit, 74ALS574137548-001
50S, 50U Integrated Circuit, 74ALS574137548-001120PIntegrated Circuit, 74AS573137547-001

120S-PSP Integrated Circuit, 34012-50 137559-001

50wIntegrated Circuit, 74ALS574137548-001120UIntegrated Circuit, 74F244137502-001
50YIntegrated Circuit, 744$573137547-001
55L-MSPIntegrated Circuit, 34010-50137538-002120W, 120Y Integrated Circuit, 744S573137547-001
60BIntegrated Circuit, 7418244137038-001135C, 135H Integrated Circuit, 74F74137436-001
135KIntegrated Circuit, 74AS32137487-001
GOP, 60SIntegrated Circuit, VRAM, 64Kx4,137553-002135MIntegrated Circuit, 741874137023-001

150 nsec (Acceptable substitute is part

no. 137553-001, Integrated Circuit,135PIntegrated Circuit, 7448573137547-001
VRAM, 64Kx4, 126 nsec.)135UIntegrated Circuit, 74AS00137480-001
60U, 60W Integrated Circuit, VRAM, 64Kx4,137553-002135WIntegrated Circuit, 744S573137547-001
150 nsec (Acceptable substitute is part135YIntegrated Circuit, 7418259137137-001

no. 137553-001, Integrated Circuit,

RAM, 64Kx4, 120 nsec.)140CIntegrated Circuit, 741S244137038-001
6OYIntegrated Circuit, 74AS138137522-001140HIntegrated Circuit, 7418393137146-001
65CIntegrated Circuit, 741S259137137-001140KIntegrated Circuit, 74F11137583-001
140MIntegrated Circuit, 74ALS74137156-002
7OP, 70SIntegrated Circuit, VRAM, 64Kx4,137553-002
150 nsec (Acceptable substitute is part140PIntegrated Circuit, 7418244137038-001
no. 137553-001, Integrated Circuit,1400Integrated Circuit, 74AS08137484-001
VRAM, 64Kx4, 120 nsec.)150CIntegrated Circuit, 7418245137134-001
70U, 70W Integrated Circuit, VRAM, 64Kx4,137553-002150EIntegrated Circuit, 7418244137038-001

150 nsec (Acceptable substitute is part

no. 137553-001, Integrated Circuit,150HIntegrated Circuit, 741874137023-001
VRAM, 64Kx4, 120 nsec.)150KIntegrated Circuit, 741$20137069-001

4-19

Page 76

illustrated Parts Lists

Race Drivin’ Compact Multisync PCB Assembly, Continued. Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
1508-GSP Integrated Circuit, 4010-50137538-002200YIntegrated Circuit, EPROM136078-1016
150UIntegrated Circuit, 7448573137547-001205BIntegrated Circuit, 40668137580-001
150WIntegrated Circuit, 74F04137437-001
150YIntegrated Circuit, 74F161137343-001210A _ Integrated Circuit, MC1488137403-001

210B _ Integrated Circuit, MC1489AL 137263-001

160CIntegrated Circuit, 7418244137038-001210C, 210D Integrated Circuit, RAM, 8Kx8,137535-006
160E‘Integrated Circuit, 74A1S161137470-001150 nsec
160HIntegrated Circuit, 74A1832137464-001210EIntegrated Circuit, 48Z02-15, RAM137442-150
160KIntegrated Circuit, 7418138137517-001
210FIntegrated Circuit, 7418245137134-001
160MIntegrated Circuit, 74F04137437-001210H, 210} Integrated Circuit, 7418244137038-001
160U_Integrated Circuit, 744832137487-001210KIntegrated Circuit, 7418244137038-001
160WIntegrated Circuit, 741874137023-001210L, 210M Integrated Circuit, 7418245137134-001
170C_Integrated Circuit, 7418245137134-001

210N _ Integrated Circuit, 741.8244 137038-001

170EIntegrated Circuit, 7418244137038-001210P—_Integrated Circuit, 741.8245137134-001
170KIntegrated Circuit, 7418148137417-001210R —_ Integrated Circuit, EPROM136078-1001
170KIntegrated Circuit, 74ALS161137470-001210SIntegrated Circuit, EPROM136078-1003
175UIntegrated Circuit, 741874137023-001
210TIntegrated Circuit, EPROM136078-1005
180C _ Integrated Circuit, 74ALS138137517-001210UIntegrated Circuit, EPROM136078-1007
180EIntegrated Circuit, 74418139137467-001210V.Integrated Circuit, EPROM136078-1009
185RIntegrated Circuit, 7419374137144-001210WIntegrated Circuit, EPROM136078-1011

185T —_ Integrated Circuit, 7418193 137128-001

210XIntegrated Circuit, EPROM136078-1013,
185U _ Integrated Circuit, 7418374137144-001210Y_Integrated Circuit, EPROM136078-1015
185WIntegrated Circuit, 741814137056-001Capacitors
190CIntegrated Circuit, 7418393137146-001clCapacite
reatpacitor, 100 HE, 35 V, Electrolytic124000-107
190EIntegrated Circuit, 74AS00137480-001@Capacitor. 01 AE, 30V; Gece10088108
—_C3-C14Capacitor, .1 WF, 50 V, Ceramic122002-104
190KIntegrated Circuit, 68010137414-002cisCapacitor, 1 Ur, 30 V, Ceramic427002-104
190NIntegrated Circuit, 7418245137134-001oAote
195R _ Integrated Circuit, 7418138137177-001Ci9-cx1Capaci
“aepacitor, .1 WF, 50 V, Ceramic122002-104
195T —_ Integrated Circuit, 741819317128-001C24-C43.Capacitor, .1 UF, 50 V, Ceramic122002-104
_—C44-C63_Capacitor, .001UF, 50 V, +10%122015-102
195U__Integrated Circuit, PROM, 825123136068-1168isangah Stor 1 ws V. Ceramic122000104
195WIntegrated Circuit, 74H1C14137605-001—_
200A _ Integrated Circuit, 68681137543-001oo:‘2
aieCapacitor, 10 pF, 100 V, Ceramic122016-100
200C, 200D ee Circuit, RAM, 8Kx8,137535-006C80-C82Capacitor, .1 UF, 50 V, Ceramic122002-104

= C83, C84 Capacitor, 100 pF, 100 V, Ceramic —_-122016-101

200EIntegrated Circuit, 48702-15, RAM137540150C8087Capacton, 1 MF, 50V, Ceramic122002-104
200F oy mlegrated Circuit, 7418245157134001€94-C106 Capacitor, .1 HF, 50 V, Ceramic122002-104
200H, 200 Integrated Circuit, 7418244137038-001114-C117 Capacitor, 1 UF, 50 V, Ceramic122002-104
200KIntegrated Circuit, SLAPSTIC137412-117C423, C124 Capacitor, 1p 50 V. Ceramic120002104

; ; 7

200%_inregested Circat, 74K1533157464002C125-C128 Capacitor, 10 HF, 35 V, Electrolytic124000-106
SoneIntegrated Circuit, HaIss8137517-001129-C137 Capacitor, .1 LF, 50 V, Ceramic122002-104
2 oN, 200P Integrated Circuit, raise 5137134-001C138, C139 Capacitor, 1000 pF, 100 V, Ceramic122016-102
Integrated Circuit,EPROM136078-1002140, C141 Capacitor, .1 UF, 50 V, Ceramic122002-104
2008Integrated Circuit, EPROM136078-1004C142Capacitor, .22 WF, 50 V, Ceramic122015-224
FatsLites dae ar EPROMetc anneC143, C144 Capacitor, .1 pF, 50 V, Ceramic122002-104
oe cue EenoM136078-1008C145.__Capacitor, 10 UF, 35 V, Electrolytic124000-106
VIntegratedCircuit, EPROM136076-1C146-C189 Capacitor, .1 HF, 50 V, Ceramic122002-104
5it.ic10:
200W _ Integrated Circuit, EPROM136078-1012€195-C202 Capacitor, .1 HF, 50 V, Ceramic122002104
200XIntegrated Circuit, EPROM136078-1014904.997 Capacitor, 1 HF, 50 V, Ceramic122002-104

4-20

Page 77

Illustrated Parts Lists

Race Drivin’ Compact Multisync PCB Assembly, Continued Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
C228Capacitor, .001 UF, 50 V, £10%122015-102Crystals
C229Capacitor, 47 pF, 100 V, Ceramic—122016-470XOSC1Oscillator, 32 MHz144008-002
230-238 Capacitor, .1 UF, 50 V, Ceramic122002-104XOSC2Crystal, 48 MHz, Oscillator Module144008-003
XOSC4Oscillator, 32 MHz144008-002
243-249 Capacitor, .1 UF, 50 V, Ceramic122002-104XTALL — Crystal, 3.6864, Standup144000-011
250 aso Capacitor, 47 pF, 100 V, Ceramic_-122016-470Diodes
5251-2:pacitor, .1 UF, 50 V, Ceramic122002-104,ai
€264273 Capacitor, .1 MF, 50 V, Ceramic122002-104oe = pod 033. Light Emittingieioie-002
274Capacitor, 47 pF 100 V, Ceramic——-122016-470- _ Boe sie le Light Emittingeiode-002

cz15-293 Capacitor, .1 UF, 50 V, Ceramic 122002-104 , ©

C298, C299 Capacitor, .1 UF, 50 V, Ceramic122002-104>Di‘‘7
€306-309 Capacitor, .1 [IF, 50 V, Ceramic122002-104oo Diode! ee Right malting.adn 002
€315-320 Capacitor, .1 LF, 50 V, Ceramic122002-104.pe wee Light Emittingtenn

C323-326 Capacitor, 10 pF, 100 V, Ceramic 122016-100 °

330-333 Capacitor, .1 UF, 50 V, Ceramic122002-104':
335, C336 Capacitor, 100 pF, 100 V, Ceramic122016-101esBide isos tiger eating{102002
C341, C342 Capacitor, .1 UF, 50 V, Ceramic122002-104R23Diode, 1N4002131048-002
C349-352 Capacitor, .1 UF, 50 V, Ceramic122002-104Transistors
€354,C355 Capacitor, .1 UF, 50 V, Ceramic122002-104Ql, Q2_Transistor, 2N6044133042-001
C358Capacitor, .1 LF, 50 V, Ceramic122002-1043Integrated Circuit, 7905137581-001
4Integrated Circuit, 7812137597-002
C359, C360 Capacitor, .001 uF, 50 V, +10%122615-102rep)Transistor, 2N3904133041-001

361-363 Capacitor, 1000 pF, 100 V, Ceramic 122016-102

€364,C365 Capacitor, .1 UF, 50 V, Ceramic122002-10426Transistor, 2N3906133040-001
C366Capacitor, 470 UF, 16 V, Electrolytic, 123004-477QqTransistor, 2N3904133041-001
Radial98Transistor, 2N3906133040-001
Q9Transistor, 2N3904133041-001
C367Capacitor, .1 UF, 50 V, Ceramic122002-104
C368Capacitor, 10 WF, 20 V, Tantalum127002-106Q10‘Transistor, 2N3906133040-001
369-377 Capacitor, .1 UF, 50 V, Ceramic122002-104Q11-Q13 Transistor, 2N3904133041-001
378Capacitor, .001 F, 50 V, +10%122015-102Resistors
C379Capacitor, .1 uF, 50 V, Ceramic122002-104RLR26Resistor, 100 Q, +5%, 1/4 W110000-101
ConnectorsR29-R45Resistor, 1 K Q, +5%, 1/4 W110000-102
BCLKConnector, Rept, 2 Ckt179178-002R46-R48_Resistor, 470 2, +5%, 1/4 W110000-471
BCLKConnector, 4 Ckt, Header, .100 Ctr.179177-004R49-R54Resistor, 4.7 K Q, +5%, 1/4 W110000-472

jl Connector, 12 Circuit, Header .250 Ctr179069-012

J2J6Connector, 11 Circuit, Header, 100 Ctr 179118-011RSSResistor, 100 Q, 45%, 1/4 W110000-101
R57-R6OResistor, 1 K Q, +5%, 1/4 W110000-102
yvConnector, Card Edge Header, 60179153-060ROLResistor, 4.7 K Q, +5%, 1/4 W110000-472
Circuit, .2 CtrR62, R63 Resistor, 220 O, +5%, 1/4 W110000-221

J8-J10 Connector, 11 Circuit, Header, .100 Ctr 179118-011

y12Connector, 9 Circuit, Header, .250 Ctr 179069-009R68Resistor, 1 K Q, #5%, 1/4 W110000-102
yi3Connector, 11 Circuit, Header, .100 Ctr 179118-011R70-R73_—Resistor, 220 Q, £5%, 1/4 W110000-221
R74, R75.Resistor, 10 K Q, +5%, 1/4 W110000-103
y4Connector, 26 Circuit, Header, .1 x .1 179261-026R76Resistor, 220 Q, +5%, 1/4 W110000-221

Dual

ysConnector, 16 Circuit, Header, .1 x .1 179261-016R77, R78 Resistor, 4.7 K Q, +5%, 1/4 W110000-472
DualR79Resistor, 47 K Q, $5%, 1/4 W110000-473
SPEEDConnector, Rept. 2 Ckt179178-002R80, R81Resistor, 1 K Q, +5%, 1/4 W110000-102
SPEEDConnector, 6 Ckt, Header, .100 Cir.179177-006R82, R83_ Resistor, 470 Q, +5%, 1/4 W110000-471
VCLKConnector, Rept, 2 Ckt179178-002R84-R88-_Resistor, 10 K Q, +5%, 1/4 W110000-103
VCLKConnector, 6 Ckt, Header, 100 Ctr179177-006R89-RO%Resistor, 33 O, +5%, 1/4 W110000-330

4-21

Page 78

Illustrated Parts Lists Race Drivin’ Compact

Race Drivin’ Compact Multisync PCB Assembly, Continued Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
R9B-101Resistor, 100 0, 45%, 1/4 W110000-101R187 _ Resistor, 330 2, £5%, 1/2 W110001-331
R102-107 Resistor, 33 Q, £59, 1/4 W110000-330R188Resistor, 1 K Q, +5%, 1/4 W110000-102
R109-111 Resistor, 100 Q, +5%, 1/4 W110000-101R189Resistor, 2.2 M Q, +5%, 1/4 W110000-225
R113-115 Resistor, 100 Q, £5%, 1/4 W110000-101RI90Resistor, 10 K Q, +5%, 1/4 W110000-103
R116-123 Resistor, 33 , 45%, 1/4 W110000-330R191Resistor, 1 K @, #5%, 1/4 W110000-102
R124Resistor, 220 2 £5%, 1/4. W110000-221R192 __ Resistor, 270 K Q, 45%, 1/4 W110000-274
R125-131 Resistor, 1 K Q, $5%, 1/4. W110000-102R193, R194 Resistor, 1 K Q, £5%, 1/4 W110000-102
R132Resistor, 4.7 K Q, £5%, 1/4 W110000-472R197Resistor, 1 K Q, +5%, 1/4 W110000-102
R134_—_Resistor, 1 K Q, 45%, 1/4 W110000-102RN1, RN2_ Resistor Network, 470x9, +5%, 1/8 W,118010-471
R145, R146 Resistor, 10 K Q, 45%, 1/4 W110000-103.SIP (40 Pin)
R147, R148 Resistor, 100 K 2, +59, 1/4 W110000-104RN3-RNS Resistor Network, R2R Ladder118015-001
R149, R150 Resistor, 10 K Q, 45%, 1/4 W110000-103RNGResistor Network, 4.7Kx9, +5%,118010-472

1/8 W, SIP (10 Pin) R151, R152 Resistor, 220 Q, 45%, 1/4 W 110000-221 sockets

R155Resistor, 0, +5%, 1/4 W110005-001'a179259-
R160, R161 Resistor, 10 K Q, £5%, 1/4 W110000-103Socket, 20 Pin, 300"eegerinat
R162, R163 Resi150 2. 45%,4 W151Socket, 24 Pin, .600'179257-024
2, KiesResiator, 150 05%, 1120090-19'Socket, 28 Pin, .600"179257-028

ca Boe 4

R168-171 Resistor, 10 K Q, £5%, 1/4 W110000-103Socket, 40 Pin, .600a i
R172, R173 Resistor, 10 Q, +5%, 1/4 W110000-1004 Piio12!
R177, R178 Resistor, 100 Q, 45%, 1/4 W110000-101aepa 900ee ies

R182-184 Resistor, 10 K Q, 45%, 1/4 W 110000-103 , Miscellaneous

R185Resistor, 1 K Q, +5%, 1/4 W110000-102swiSwitch, 8-Position DIP160031-008
R186Resistor, 82 Q, +5%, 1/4 W110000-820Test Point179051-001

4-22

Page 79

Race Drivin’ Compact Iustrated Parts Lists

N O T E S

4-23

Page 80

Illustrated Parts Lists Race Drivin’ Compact

i I

TDAZO30 VER APU ATARI GAMES|GPAB

FJ nn

Figure 4-11 Race Drivin’ Compact APU PCB Assembly A044431-02 D

4-24

Page 81

Illustrated Parts Lists

Race Drivin’ Compact APU PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.

Capacitors Transistors

C1Capacitor, .1 HF, 50 V, Ceramic122002-104Ql, Q2Integrated Circuit, TDA2030137301-001
c2Capacitor, .22 UE, 50 V, Ceramic122015-224Q3Integrated Circuit, 7815, Standup——-137598-001
C3Capacitor, .1 WF, 50 V, Ceramic122002-104Resistors
4Capacitor, .001 HF, 50 V, Ceramic122002-102RIResistor, 10 K Q, 45%, 1/4 W110000-103
éaa.R2Resistor, 1, +5%, 1/4 W110000-010
3Capacitor, .22 uF, 50 V, Ceramic-122015-224R3,R4_—_Resistor, 22 K Q, $5%, 1/4 W110000-223
C6Capacitor, 22 UF, 35 V, Electrolytic124000-226RSResistor,1K ©. 45%, 1/4 W110000.102
C7-Cl4_—Capacitor, .1 UF, 50 V, Ceramic122002-104,°
CIECISCapacitor 3300 UF, 25 V, Electrolytic, 123003238R6Resistor, 10, 45%, 1/4 W110000-100
RadialR7Resistor, 1 K Q, 45%, 1/4 W110000-102
,.R8,R9Resistor, 22 K Q, 45%, 1/4 W110000-223
cioCapacitor, .1 IF, 50 V, Ceramic122002-104eenResistor, 1, 459 1/4 W110000-010
C20, C21 Capacitor, 3300 UF, 25 V, Electrolytic, 123003-338r?.

Radial . 110000-10:

22Capacitor, 22 UF, 35 V, Electrolytic124000-226saeResistor, 10K Q, $5%, 1/4 W3
23Capacitor, .22 uF, 50 V, Ceramic122015-224Miscellaneous

Connector, 2 Ckt, Header, 156 Ctr 179213-002

C24Capacitor, 1 UF, 50 V, Ceramic122002-104Connector, 3 Ckt, Header, 156 Ctr179213-003
C25,Capacitor, .001 LF, 50 V, Ceramic122002-102Connector, 6 Ckt, Header, .156 Ctr179213-006
C26Capacitor, .22 HF, 50 V, Ceramic122015-224Connector, 9 Ckt, Header, 156 Ctr179213-009
C27Capacitor, .1 UF, 50 V, Ceramic122002-104

Dt HS1, HS2 Heatsink, TDA2030 178190-032

i1:1)-124
CRI-CR6Diode, 1N40011104-001—«“HS3_——_Heatsink, 7815ai

CR7-CR12 Diode, 1N5401 131051-002

4-25

Page 82

4-26 Figure 4-12 Race Drivin’ Compact Motor Amplifier PCB Assembly A046640-01 A Taito Tapas Illustrated Parts Lists

Page 83

Illustrated Parts Lists

Race Drivin’ Compact Motor Amplifier PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.

Capacitors

C1-C4Capacitor, 4700 UF, 25 V, Electrolytic, 123021-478QsTransistor, MPSU57133008-002
RadialQ9Transistor, IRF630133039-001
csCapacitor, 100 UF, 16 V, Electrolytic124008-107Q10Transistor, IRF9640133037-001
©6,C7Capacitor, .1 BE 50 V, Ceramic122002-104Sesistors
C8,C9Capacitor, 1000 pF, 100 V, Ceramic122016-102R1,R2Resistor,1KQ, 18sion30-02
cioCapacitor,-v,R3Resistor, 4.7 KQ, £5%, 1/4 W110000-472
cuCapacitor abe 50 oe CeramiceanR4,R5Resistor, 1.2 KQ, 15%, 1/4 W110000-122
C12-C18Capacitor, 1 uF, 50 V, Ceramic122002-104R6Resistor, 2.4 KO, $59, 1/4 WLOGO} 242
€24-C26Capacitor, .01 UF, 50 V, Ceramic122002-103R7,R8Resistor, 2.2 KO, 4596, 1/4.110000-222
i‘.ROResistor, 1 KQ, 45%, 1/4 W110000-102
,wee:R11Resistor, 100 KQ, +5%, 1/4 W110000-104

Diodes

CR1-CR4_Diode, 1N5401131051-002R12Resistor, 15 KQ, 45%, 1/4 W110000-153
CRS, CR6 Diode, 1N5352B, +5%, Zener131049-220R13, R14 Resistor, 10 2, £5%, 1/4 W110000-100
CRTDiode, 1N4148131033-001RISResistor, 100 Q, +5%, 1/4 W110000-101
‘CRB, CRO Diode, 1N4747, Zener131009-220RI6Resistor, 10 KQ, +5%, 1/4 W110000-103
CR10, CRI1 Diode, IN5362, 45%, Zener131049-230R18-R20Resistor, 2.2 KO, 45%, 1/4 W110000-222
CR12, CR13 Diode, 1N5401131051-002R24, R25 Resistor, 100 Q, 45%, 1/4 W110000-101
CR14, CRIS Diode, 1N914131052-001R26Resistor, 0.5 Q,5 W, Wirewound—_116029-5000
R37Resistor, 5.6 KQ, +5%, 1/4 W110000-562

Fuses

FULFuse, 4AMP, 250 V146007-4022RagResistor, 2.2 KQ, +5%, 1/4 W110000-222
#2Fuse, 4AMP, 250 V14607-4022RagoResistor, 100 Q, +5%, 1/4 W110000-101
HeatsinksR41-R44_Resistor, 150 Q, $5%, 1/4 W110060-151
HTS1, HTS2 Heatsink, TDA2030178190-032R45,Resistor, 100 Q, +5%, 1/4 W110000-101
HTS3Heatsink, Power Supply047084-01
R46, R47Resistor, 10 KQ, +5%, 1/4 W110000-103

Integrated Circuits

ICc1Integrated Circuit, DAC-08137159-001Miscellaneous
1C3, IC4Integrated Circuit, 7418174137122-001FU2, FU2-FU1Fuseclip179050-002
Ic5Integrated Circuit, 7406137052-001FB1, FB2 Ferrite Bead141003-001
1C6Integrated Cireuit, ADOPO7CN137523-001

ji Connector, 3 Circuit, Header, .156 Ctr 179213-003

Transistorsj2Connector, 2 Circuit, Header, .250 Ctr 179069-002
QlTransistor, 2N3904133041-001J6Connector, 16 Circuit, Header,179261-016
3Transistor, TIP145133046-0011X .1 Dual
QtTransistor, TIP140133047-001OPT1Connector, 6 Ckt, Header, .100 Ctr179177-006
for)‘Transistor, MPS-U07, 100 V, 2 A133003-001

4-27

Page 84

Illustrated Parts Lists

Figure 4-13 Encoder Disk PCB Assembly A046689-01 A Figure 4-14 Centering Disk PCB Assembly A046691-01 B

Encoder Disk PCB Centering Disk PCB Parts List Parts List

Designator Description Part No. Designator Description Part No.

R1150Q, 1/4 W, 5% Resistor110000-151RL220Q, 1/4 W, 5% Resistor110000-221
OSR1NPN Out, Dual Slotted Opto-Sensor—138000-001OSR1NPN Out, Single Slotted Opto-Sensor138000-001
ju4-Ckt., 156 Ctr., Locking Connector—79-58356ji4-Ckt., .156 Ctr., Locking Connector _ 79-58356

4-28

Page 85

Ak, Race Drivin” Statistics Sheet ATARI GAMES Location: Date Recorded:

Meter:

Super

OriginalAutocrossStuntOriginal© AutocrossStunt
Left Coins:Laps by Track:Free Games by Track:

Right Coins:

Aux Coins:—No X Games by Track:Total Games by Track:
Idle Min:——
Active Min:1X Play Games by Track:Total Time by Track:

Auto Games: —

Error Count:2X Play Games by Track:‘Avg Time by Track (sec):
Total Games:——_—

3+ X Play Games by Track: Games by Car:

Champ Laps by Track:

2 Player Games by Track: inst Rel:

2 Player Time by Track:Rpl Abrts:—
_Rpl Secs:—__

Total Credits: ——_——_ Avg Time/Credit:

TimeTimeNo. of Games”TimeNo. of GamesTimeNo. of Games
0-99_180-199280-299380-399
100-119_200-219300-319—_—400-419
120-139220-239320-339420-439
140-159240-259340-359440-459
160-179260-279360-379460 & UP

Watch Dog Resets Bad Poly Buff Error ‘Bus Error MSP Timeout Error ‘Address Error ADSP Timeout Error IMlegal Inst Error GSP Timeout Error Divide by Zero Er Generic Error Chk Inst Error NMI Error (Trap Error Spur Exptn Error Piv Vio Error ASIC 65 Timeout Error GSP Handshake Error Illegal Error Code

Page 86

Race Drivin’ Statistics Sheet

Location: Date Recorded:

Meter:

Midnight 1:00 a.m. 2:00 am. 3:00 a.m.

4:00 a.m. 5:00 an. 6:00 am.

7:00 a.m. 8:00 a.m. 9:00 a.m.

10:00 a.m. 11:00 a.m,

Noon 1:00 p.m. 2:00 p.m. 3:00 p.m.

4:00 p.m. 5:00 p.m. ....., 6:00 p.m.

7:00 p.m. 8:00 p.m. 9:00 p.m.

10:00 p.m. 11:00 p.m.

Page 87

feel fell pel el fel fel feted pele pele pel fel pele feted peeled feted pelfelelfelred [ca]

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displ: and video-dise players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse. neglect. alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Excepl for any express warraity set forth in a written contract between Seller and Buyer which coutract supersedes the terns berein, this warranty is expressed in liew of all otber warranties expressed or implied. including the implied warranties of mercbantability and fitness Jor a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor autborizes any otber person to assume for the Seller any other liabilities in connection with the sale of products by Seller. Pree eee eee ele elele ele elrelel elated ele elated ele pele federal feted

lela pled pel el pel pel ed pel ped pele pele pel el pele pel fel pelea el fel el felelfelrel fel [ca)

The use of any non-Atii parts may void your warranty, according to the terms of the Warranty. The use of ny non-Atui parts may also adversely affect the safety of your oth Be very cautious in using non-Atiri-supplied arder to en your safety game and cause injury (0 you components with our games. Atari distributors are indep tely owned and operated. In their judgan Atari parts or accessories. Atari Games © quality, suitability. or safety of any: non-Atari labor which is performed by such distributor ment they may’ sell parts or accessories other Corporation cannot be responsible for part or any modification includi

Page 88

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.