CATHODE RAY TOMES

Bally Midways MCR II System Games Standardized General Instructions (M051-00986-A025)

MCR II System Games (Bally/Midway, 1983) · Manual · 65 pages · 50 sections · original scan

Page 1

) s

MCR I

System Games

Bally/Midway

We 4075 é ahklih- Park;

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment generates. uses. and can radiate radio frequency energy and if not and used in accordance with the instructions manual. may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated in acommerical environment. Operation of this equipment in a residential area 1s likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

ee pSeOne” BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF S! LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

CStallly|MIDWAY

OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497

® COPYRIGHT MCMLXXxXIII BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL iS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

DESCRIPTION

Vi. TABLE OF CONTENTS

Location and Setup .. Inspection .... Installation . Self-Test .... Game Volume Adjustment Control . Option Settings

Self-Test Mode ..

Maintenance and Repair Cleaning .......... Fuse Replacement . Opening the Control anel . Removal of the Main Dispiay Glass & TV. Bezel 13-4 TN. Monitor Replacement.......... 3-5 Printed Circuit Board Replacement. .3-8 Opening the Attraction Panel . -3-10 Servicing the Control Panel BI 23-12

Technical Troubleshooting .. Introduction . General Suggestions . : Harness Component Troubleshooting Transformer and Line Voltage Problems A Glossary of Microprocessor Terms . Introduction to the Z80 CPU.. General Purpose Registers .. Arithmetic and Logic Unit (ALU) . Introduction Register and CPU Control Z80 CPU Pin Description ............. MCR II System P.C. Board Jumper Options = peEEbR EERE E NREBRROONSI 4

Coin Door Maintenance -.5-1 Metal Coin Acceptor Mechanisms 5-1 Plastic Coin Acceptor Mechanisms... 25-3

TV. Monitor Manual ......... 0.0... cece cere eee ete tere bette better teens Introduction : Symptom Diagnosis .. Guide to Schematic Symbols . Troubleshooting...... Theory of Operation.. Differences Between Monitors Controls You May Not Touch . Parts Interchangeability .... Picture Tube Interchangeabiltty . Wells Gardner Monitor Schematic — 19” . Wells Gardner Monitor Replacement Parts List Eiectrohome Monitor Schematic — 19”..... Electrohome Monitor Replacement Parts List . Electrohome Monitor Schematic — 13”..... Electrohome Monitor Replacement Parts List . Zenith Monitor — Sweep Board Schematic . Zenith Monitor — Sweep Board Repiacement Zenith Monitor Main Board Schematic .............. Zenith Monitor Main Board Replacement Parts List .. Zenith Monitor — CRT Socket Board Replacement Parts List . Zenith Monitor — CRT Socket Board Schematic Zenith Monitor Width Step Assy. Schematic .. Zenith Monitor Interconnect for Video Game Schematic

Page 4

TABLE OF FIGURES

FIGURE PAGE

Location of Serial No., Interlock Switch, On/Off Switch, and Major Sub-Assemblies ..... Major Sub-Assemblies (Cont. from Fig. 1-1) . Interlock Switch Operation . Location of Volume Control Location of Option Switches Option Switch Settings ... Self-Test — Menue... Self-Test — Sounds .. Self-Test — Player Inputs . Self-Test — Bookkeeping. Self-Test — Time Report . Self-Test — Score Report. Self-Test — Set-Up Options . Self-Test — Channel Test...............5 Location of Hardware Master Reset Switch Location of FUSES ........--. eee c eee e eee Opening the Control Panel — Upright & Min Opening the Cocktail Game .......... Removing the Control! Panel — Cocktail Removing the Main Display Glass & T.V. Bezel — Uprig Removing the Main Display Glass & T.V. Bezel — Mini . Removing the Top Glass & T.V. Bezel — Mini Removing the Monitor — Upright .. Removing the Monitor — Mini . Opening the Cocktail Game ... Removing the Monitor — Cocktail . Removing P.C.B.'s.........-:e eee Removing P.C.B.'s from Card Rack . Opening the Attraction Panel — Upright . Replacing Fluorescent Light Fixture . . Opening the Attraction Panel — Mini. Servicing Control Panel Black Light — Upright Removing Black Light Tube Mtg. Brkt. — Upright Removing and Replacing the Coin Acceptor Cleaning the Metal Coin Acceptor . Lubricating the Metal Coin Acceptor . Opening the Plastic Coin Acceptor .... Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters .. Q

PP Se TI rare PYM opoos BOOOVMYNYAGKRAGON @a@>oa0c

Oona Oda SoUNOHAONADSSASALAAGDGRORA SEOYOHOKYOONNY NNN ND

AAADAALEEOYLEY Ghowms sti biltiin ~ PEE SYSHROVAIGS on

p ALLALe yVN>A50 PRLPE SLE SELL PE LES EEE PE PNNNHD

Kodnwws

Page 5

I. Location and Setup

INSPECTION: 1, Remove the game from its shipping crate.

  • Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? D Any broken controls? 0 Any broken glass or plastic? D Just look it over closely and make a note of any signs of damage.
  • Remove the shipping cleats from the bottom ofthe cabinet.
  • Install the four levelers, one at each corner of the cabinet. Level the cabinet.
  • Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 1-1. O Also check to make sure all plug-in connectors on the wire harness are firmly seated.
NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are properly lined up.

Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO GONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. Make sure ail printed circuit boards (P.C.B.’s) are firmly seated in their connectors. These connectors are a!s0 keyed. The P.C.B.’s willonly go into them one way without being damaged. TD Note the location of the game's serial number. See Figure 1-1. O Check all major subassemblies to be sure they are mounted securely. These are called out in Figures 1-1 & 1-2. Power supply. Control panels(s). T.V. monitor Other P.C.B.’s and/or P.C.B. rack, etc. Power supply cha$sis assembly. . Make a note of any problems that can't be easily corrected. Call your distributor and/or service man about your problem (ist.

1-1 INSTALLATION:

  • Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) O Humidity: Not over 95% relative O Space required: Upright 25" x 32” (63 x 81cm) APPROX. Mini 20” x 24” (50 x 60cm) Cocktail 32” x 22” (81 x 55cm) DO Game height: Upright 70" (175cm) APPROX. Mini 61" (153cm) Cocktail 29" (73cm)

Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main

power supply transformer on your game to be sure

they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps.

If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem, Otherwise you could damage your game.

Interlock and power ON/OFF switches. See Figure 1-1. To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models). O When any access door is opened, the interlock switch installed there turns off all power to the game.

Page 6

SERIAL NUMBER

ON/OFF SERIAL SWITCH NUMBER TY. MONITOR

TV. MONITOR

INTERLOCK SWITCH

Loaic INTERLOCK : | / BOARDS SWITCH POWER SUPPLY P.C.B. POWER q CHASSIS POWER

SUPPLY ‘NOT SEEN POWER SUPPLY CHASSIS ‘ ; P.C.B. (NOT SEEN)

ON/OFF SWITCH

TW. MONITOR

POWER SUPPLY SERIAL NUMBER CHASSIS (MAY BE LOCATED ON ANY CORNER) POWER SUPPLY P.C.B. Loaic BOARDS

CONTROL PANEL (PLAYER 2) CONTROL PANEL (PLAYER 1)

ON/OFF SWITCH

evict UNDER TABLE

ON PLAYER 2 (INSIDE DOOR) COCKTAIL SIDE

Figure 1-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies

1-2

Page 7

UPRIGHT CONTROL PANEL

Figure 1-2 Major Sub-Assemblies (cont. from Fig. 1-1)

O Check each operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 1-1. Turn the game on and allow it to warm up a few minutes.

Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). interlock switch for proper

As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). lf this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wait outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 1-3.

Figure 1-3 Interlock Switch Operation

Page 8

SELF-TEST: Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. See the SELF- TEST section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

GAME VOLUME ADJUSTMENT CONTROL: See Figure 1-4. The game volume control pot is located just inside the cabinet coin door frame. There is only one pot. For adjustment, it may be reached through the coin door on ALL models. To make the sounds louder, turn the pots clockwise as you face them (7A). To make the sounds less loud, turn the pots counterclockwise as you face them (47 ).

OPTION SETTINGS: To change the most common option settings, you DO. NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self- Test mode. The Self-Test switch is located just inside the cabinet coin door frame as you face it. When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you

OPTION SWITCH 3 SERVICE CREDIT SWITCH

SELF-TEST SWITCH

VOLUME ADJUSTMENT

Figure 1-4 Location of Volume Control

must change one of the switches that is located on one of the game's P.C. boards, it is also recommended that you perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The P.C. Board option switch settings, and what they will make the game do are shown in Figure 1-6. These switches are MAINLY INTENDED for use bya technician who is checking and/or performing tests on the game. See Figure 1-5 for option switch locations.

NOTE: In order to set the option switches located on the game's P.C. Boards, these Boards need not be removed from their card rack.

OPTION SWITCH 1

Figure 1-5 Location of Option Switches

1-4

Page 9

Il. Self-Test Mode

The Self-Test mode is a special mode for checking game play statistics as well as garne switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test WILL NOT cause the game to erase any CREDITS it has in its memory when the Self-Test mode is entered. You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on (the Self-Test switch is located just inside the cabinet coin door frame as you face it). When this is done, the game will react as follows:
  • If the game is in the Attract mode when the Seif- Test switch is moved to the “ON” position, it will finish the sequence and then go into the Self-Test mode. This is illustrated by the display of the Self- Test Mode Menue on the monitor screen, . If the game is in the Ready-To-Play mode or the Play mode when the Self-Test switch is slid to the “ON” position, it WILL NOT go into the Self-Test mode until AFTER the game is over. At this point, the game will go into the Self-Test mode. Again, this is illustrated by the display of the Self-Test Mode Menue on the monitor screen. The fastest way to enter the Self-Test mode is to slide the Self-Test switch to the “ON” position and then activate the “TILT” switch located on the back side of the coin door just below the lock mechanism. The game will then IMMEDIATELY go into the Self-Test mode. The Self-Test mode has eight (8) major categories as illustrated by Figure 2-1.
  • It is easy to select what category you want to enier. By following the ON SCREEN instructions, the Cursor at the left of the screen can be moved UP or DOWN until it is in front of the category you want to test. . After the Cursor has been positioned, follow the ON SCREEN instructions again, and the monitor screen will display the test category you have selected.
NOTE:There is one exception to this. If you select the “PRE-SET” category on the Self-Test Mode Menue, EVERYTHING, | repeat — EVERYTHING
  • including ALL information in the “BOOKKEEP- ING” mode, and ALL operator selected options, wili be set back to zero (“0”) and to the factory recommended settings — respectively.

SELECT DESIRED TEST

1 SELF DIAGNOSTICS 2 SOUNDS 3 PLAYER INPUT 4 BOOKKEEPING 5 MACHINE SETUP 6 CHANNEL TEST 7 PRESET 8 GRID DISPLAY

POSITION CURSOR BY ....

Figure 2-1 Self-Test — Menue

O Once you are IN one of the Self-Test mode categories, FOLLOW THE ON-SCREEN IN- STRUCTIONS TO COMPLETE THE TEST.

  • The next group of Figures show the CORRECT screen presentation for EACH category of the Self-Test mode. During the SELF DIAGNOSTICS section of the Self-Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you will see a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from the top down. Third, you will see the screen painted Red, Blue, and Green in bars from the top down. Fourth, all the different colored bars you saw “Second” are displayed again. And fifth, the different colored bars are replaced by an exit message. If you do not exit, the test will repeat itself. This feature was designed into the game to enable over-night testing for an intermittent hardware problem. If the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through what is described above, the game will give you a written message as to which parts are bad. This message includes their 1.D.’s and their P.C. Board locations.
Page 10

During the SOUNDS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1a. Cin this category, each of the game's separate sounds can be checked individually in any order — or — you can tell the game to check them ail in order. During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1b. CO In this category, each of the game's player operated controls —- including the coin switches on the back side of the coin door — may be checked individually. A game sound will be heard as each switch/control is actuated. If no game

: SELECT A SOUND 1 ALL SOUNDS 2 EXIT

REMAINDER OF GAME SOUNDS

CALLED QUT IN

ORDER

POSITION CURSOR BY... Figure 2-1a Self-Test — Sounds

PLAYER INPUTS

PLI FIRE

h of Bevice activated Js. spelled oat in the space | As the Player Inpui Switches and Devices are activated. the Si indicated.

MINE UPRIGHT

1 COIN METER

ACTIVATE ALL PLAYER (NPUT SWITCHES AND DEVICES

HIT TILT TO EXIT

Figure 2-1b Self-Test — Player Inputs

2-2 sound is heard, that switch/control is either not working, miswired, or disconnected. Check it out thoroughly. During the BOOKKEEPING section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1c. D In this category a basic bookkeeping function is performed. And with the selection of the “TIME REPORT” and the “SCORE REPORT”, detailed breakdowns of game times and scores may be obtained. In the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like those shown in Figures 2-1d and 2-1e respectively.

SELECT A REPORT OR EXIT CHUTE 1 COINS CHUTE 2 COINS LONGEST GAME

SHORTEST. GAME HIGHEST SCORE 36)

05.18 00 43. - 86310 LOWEST SCORE 120 TIME REPORT SCORE REPORT EXIT

POSITION CURSOR BY...

Figure 2-1c Self-Test — Bookkeeping

TIME REPORT 0 10.30 SEC 30 T0 60 “SEC 60 70.90 SEC 90 10 120 SEC 120 TO 150 SEC 150 10 180 SEC 3 10.4 MIN 4705 MIN 5 70 6 MIN OVER 6 MIN

Figure 2-1d Self-Test — Time Report

Page 11

SCORE REPORT

0 TO 5000 PTS © 5000 TO 10000 PTS 10000 TO 20000 PTS 20000 TO 40000 PTS 40000 TC 70000 PTS 70000 T@ 100000 PTS 100000 T0.150000 PTS 150000 TO 200000 PTS 200000 TO 250000 PTS OVER 250000 PTS

Figure 2-1e Self-Test — Score Report

During the SETUP OPTIONS section of the Self-Test

mode, the game will give a display which looks similar to that shown in Figure 2-1f. O In this category, all common game options may be changed from the control console: coins per credit, credits per base, bonus base(s) awarded at, difficulty level - -, and so on.

SETUP OPTIONS

COIN CHUTE 1 *T COINS FOR “TL GREDITS

COIN CHUTE 2 “T COINS FOR “TP CREDITS

“| GREDITS FOR *3 BASES IST EXTRA BASE AT *20000 POINTS

ADDITIONAL BASE EVERY *20000 POINTS

*3 DIFFICULTY LEVEL

  • = Factory recommended setting: Figure 2-1f Self-Test — Set-Up Options

DIFFICULTY LEVEL EXPLANATION: The Difficulty Level setting has a range of 1 to 9. With 1 being the easiest level of play and 9 being the most difficult level of play. We recommend that a setting of 3 be used as a beginning point.

2-3 Game play can then be made MORE difficult or LESS difficult, according to the skill levels attained by the players in your area. CHANNEL TEST: During the CHANNEL TEST section of the Self-Test mode, the game will give a display which looks iike that shown in Figure 2-1g. C In this category, the game conducts a test of its SOUND SYSTEM. Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until exited. It then goes back to the Self-Test Mode Menue. During the GRID DISPLAY section of the Self-Test mode, the game shows awhite cross hatch pattern on the monitor screen. This is for alignment and/or test purposes. This pattern will remain on the monitor screen until exited. The game will then go back to the Self-Test Mode Menue. To leave the Self-Test mode, simply slide the Self-Test switch to the “OFF” position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will return to the monitor screen.

CHANNEL TEST

CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 CHANNEL 5 CHANNEL 6

Figure 2-1g Self-Test — Channel Test

RACK ADVANCE: The game can be made to advance through the various racks by beginning a game and THEN sliding the Self-Test switch to the “ON” position. After this has been done, each time you depress the ONE PLAYER BUTTON the game will advance one rack. When you reach the desired rack, slide the Self-Test switch to the “OFF” position. (If you leave the Seif- Test switch in the “ON” position, the game will gointo the Self-Test mode when you are finished playing.)

Page 12

CROSS HATCH PATTERN:

A cross hatch pattern is shown on the screen when power is first turned on to the game, when the TILT Switch is actuated, and during the “SELF DIAGNOS- TIC” portion of the Self-Test mode, and during the “GRID DISPLAY” portion of the Self-Test mode. This pattern may be kept on the screen for adjustment purposes as described earlier.

When you are finished using the cross hatch pattern, simply exit at the GRID DISPLAY to return to the Seif- Test Mode Menue. HARDWARE MASTER RESET SWITCH: There are two of these little red switches, one on the Sound I/O Board and one on the CPU Board, located as shown in Figure 2-2. The function of each of these switches — when pressed -- is to make the game think it has JUST been turned on. They set up an “initial power-up” condition. We DO NOT recommend that you indiscriminately press EITHER of these switches. They should ONLY be used if there is a major problem encountered while testing the P.C. Boards.

HARDWARE MASTER RESET SWITCH

Figure 2-2 Location of Hardware Master Reset Switch

2-4

Page 13

Ill. Maintenance and Repair

Your NEW game needs Certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece ot plastic.

FUSE REPLACEMENT This game contains several fuses located as shown in Figure 3-1.

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Supply Chassis and Power Supply P.C. Board.
  • MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Supply Chassis and Power Supply P.C. Board.
  • COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Supply Chassis and the Power Supply P.C. Board. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of your game manual. See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of your game manual for information on these fuses.

FUSES LOCATED ON POWER SUPPLY BOARD AND POWER SUPPLY CHASSIS

Figure 3-1 Location of Fuses

Page 14

OPENING THE CONTROL PANEL

  • UPRIGHT MODEL: See Figure 3-2. O The control panel is held in place by two or three latches, one on the left side and one on the right side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their jatch plates. 0 To remove the contro! panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap. The control panei is now free and can be removed. O To reinstall the control panel, reverse this procedure.

MINI 2, MINI MODEL: See Figure 3-2. O The control panel is held in place by two latches, one on the right side, and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the controi panel. Once they are released, unhook them from their latch plates. 0 To remove the controi panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the contro! panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap. The control panei is now free and can be removed. O To reinstall the control panel, reverse this procedure.

UPRIGHT

Figure 3-2 Opening the Contrel Panel — Upright & Mini

Page 15

CLAMPS

Figure 3-3 Opening the Cocktail Game

  • COCKTAIL TABLE MODEL: See Figure 3-4. O Each control panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 3-3.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!!

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 3-3.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in place. See Figure 3-4. O To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. O To reinstall the control panel, reverse this procedure. LIFT CONTROL UP

REMOVE

  • SCREWS , EACH SIDE

REMOVE(3) SCREWS

Figure 3-4 Removing the Control Panel — Cocktail

Page 16

REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE TV. BEZEL ASSEMBLY

1. UPRIGHT MODEL: See Figure 3-5.

NOTE: In order to do this, the control panel MUST be removed first. See the “Upright Model” procedure. D Turn the power to the game off and remove the control panel. This gets the control panel stick out of the way so the main-display-glass can be removed. Remove the screws securing the main-displayglass retainer and the main-display-glass in place as shown in Figure 3-5 and lift out the main-display-glass. (Certain models only.) 1 Remove the screws which secure the T.V. bezel assembly in place. O The T.V. bezel assembly is now free and can be slid out of the cabinet. G To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure.

DISPLAY GLASS

GLAss CLAMPING PLATE (CERTAIN MODELS)

Figure 3-5 Removing the Main Display Glass & T.V. Bezel — Upright

  • MINI MODEL: See Figure 3-6.

3-4

NOTE: In order to do this, the control panel MUST be removed first. See above “Mini Model” procedure. Turn the power off to the game and remove the control panel. O Remove the screws which secure the glass clamping plate. See Figure 3-6. C Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. Q By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out.

Remove the screws which secure the T.V. bezel assembly and lift it out.

NOTE: Use the hole in the center of the maindisplay-glass support to grasp it. O Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.

DISPLAY GLASS

GLASS CLAMPING PLATE

Figure 3-6 Removing the Main Display Glass & T.V. Bezel — Mini

Page 17

. COCKTAIL TABLE MODEL: See Figure 3-7.

NOTE: This may be done with the table top in the closed or the open position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST. O Remove the screws which secure the table top glass Clamps in place. O Remove the table top glass. C1 Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed. O To reinstail the T.V. bezel assembly and the table top glass, reverse this procedure.

Figure 3-7 Removing the Top Glass & T.V. Bezel

  • Mini T.V. MONITOR REPLACEMENT
CAUTION: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands? In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.
  • UPRIGHT MODEL: See Figure 3-8. 0 Turn power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. O Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Upright Model” procedure. 0 With the removal of only four bolts, the T.V. monitor and its mounting bracket will be loose. O The monitor mounting bracket slides on top of and against two metal guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. O To reinstall the T.V. monitor, reverse this Procedure. C After replacing the T.V. monitor, be sure to run the game Self-Test. . MINI MODEL: See Figure 3-9. Q Turn the power off to the game. Open the rear access door. © Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. O Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Mini Model” procedure. O With the removal of only four bolts, the T.V. Monitor will be loose.
CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fal! out of the cabinet.

3-5

Page 18

O The monitor is removed by supporting it and pulling straight back. (BE CAREFUL not to hit monitor on its rear support bracket.) O To reinstall the T.V. monitor, reverse this procedure. D After replacing the T.V. monitor, be sure to run the game Self-Test.

  • COCKTAIL TABLE MODEL: See Figure 3-11. O Turn the power off to the game. O Open the ccin box door and release the two latches indicated in Figure 3-10.

REMOVE (4) BOLTS

Figure 3-8 Removing the Monitor — Upright

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!!

O Once the latches are released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 3-10.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

REMOVE (4) BOLTS

Figure 3-9 Removing the Monitor — Mini

3-6

Page 19

Figure 3-10 Opening the Cocktail Game

O Remove the screws which hold the table top glass clamps in place. G Remove the table top glass. O Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor fromall its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. C Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 3-11. O Close the Cocktail Table and re-latch it.

O Remove the screws which secure the T.V. moni~ tor mounting brackets to the edges of the slot cut in the table top. See Figure 3-11. Q Pry up the end of each monitor mounting bracket with a screwdriver or similar tool untii you can grasp them both. C Lift the T.V. monitor straight up and out of the table top being very careful not to bump the neck of the picture tube. O To reinstall the T.V. monitor assembly, reverse this procedure. Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. C After replacing the T.V. monitor, be sure to run the game Self-Test. REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR STRAIGHT UP

ae 4 SCREWS (2 EACH SIDE)

Figure 3-11 Removing the Monitor — Cocktail

Page 20

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT

  • UPRIGHT MODEL: See Figure 3-12. O Turn the power to the game off. O Unlock and open the rear access door. O To reinstall the above P.C.B.’s, reverse this procedure.

O Disconnect all cabling from the P.C. boardsand ToT: B.¢.B.s are all keyed and will ONLY fit into lift them out of their card rack. | | their connectors one way without forcing them. O Disconnect the linear power supply board from The plugs on the cable harness which connectit to all its cabling, remove the P.C.B. supports indi- the P.C.B.’s are also keyed and will ONLY go onto caied in Figure 3-12, and slide the linear power their connectors one way without forcing them. supply board out the back of the cabinet.

REMOVE (2) SUPPORTS

COCKTAIL REMOVE REMOVE SUPPORT SUPPORT

ae

iS)

UPRIGHT

Figure 3-12 Removing P.C.B.’s

3-8

Page 21

REMOVE SCREWS FROM SIDE OF CABINET TO REMOVE LOGIC BOARDS

Figure 3-13 Removing P.C.B.’s from Card Rack

  • MINI MODEL: See Figure 3-12. O Turn the power off to the game.

O Unlock and open the rear access door.

Q Disconnect all cabling from the P.C. boards and lift them out of their card rack.

O Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 3-12, and slide the linear power supply board out the back of the cabinet. O To reinstall the above P.C.B.’s, reverse this procedure.

  • COCKTAIL TABLE MODEL: See Figure 3-12. O Turn the power off to the game.

O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 3-10.

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!

3-9 Once they're released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 3-10.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

O To remove the linear power supply board. See Figure 3-12. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports Once these are removed, the linear power supply can be lifted out the top of the cabinet. To reinstall the linear power supply board, reverse this procedure. G To remove the P.C. boards from the card rack. See Figure 3-13. Disconnect them from ALL their cabling. The P.C. boards are now free and can be slid from their rack.

O To reinstall the P.C. boards, procedure. reverse this

Page 22

OPENING THE ATTRACTION PANEL

  • UPRIGHT MODEL: See Figure 3-14. O Turn the power to the game off. O Opening the attraction panel: REMOVE SCREWS ON TOP Remove the screws which secure the top

bracket in place. (They are on its top side.) See PANEL

Figure 3-14, Remove the top bracket and slide up the attrac- | ition panel. This exposes the attraction panel fluorescent light tube and its mounting bracket + a ad assembly. To reinstall the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

I

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube. C Replacing the fluorescent tube starter. See Fig- > ure 3-15, = = Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure.

O Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game.

Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out of the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure.

O Replacing the speaker. Figure 3-14 Opening the Attraction Panel — Upright Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. 2. MINI MODEL. See Figure 3-16. Remove the nuts and bolts which secure the a n hi a speaker and speaker grill in place and set them O Turn the power off to the game and the speaker grill aside. O Remove the screws which secure the top Once the bolts which secure the speaker in Dracketin place. (They are on its top side.) See place are removed, the speaker may be re- Figure 3-16. moved through the opening where the attrac- O Remove the top bracket and slide up the attraction panel was. tion panel. This exposes the attraction panel Reverse this procedure to reinstall the speaker. light bulbs and their mounting board.

3-10

Page 23

FLUORESCENT TUBE STARTER

1/4 TURN TO REPLACE

Figure 3-15 Replacing Fluorescent Tube Starter

O To service the light bulbs and their mounting board: REMOVE TOP Turn the power to the game back on so you can BRACKET AND see which bulbs are burnt out. SLIDE HEADER UP. Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new buibs are gently pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unpiug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reverse this procedure. O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.

  • THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL. Figure 3-16 Opening the Attraction Panel — Mini

3-11

Page 24

SERVICING THE CONTROL PANEL BLACK LIGHT (CERTAIN UPRIGHT MODELS ONLY)

  • Be sure the power is off to the game.
  • Remove the control panel as described previously. This exposes the bottom row of screws which secure the control panel support bracket and the black light protector in place. See Figure 3-17.
  • Remove ail the screws which secure the above items in place and set them aside. O The black light tube may be replaced at this time by reaching through the space where the light protector was before you removed it.
WARNING: If you drop a black light tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any black light tube.
  • Replacing the black light tube starter. See Figure 3-15. © Remove the black light tube. 0 Rernove the screws which secure the black light tube mounting bracket to the cabinet. See Figure 3-18. The mounting bracket is now loose and can be pulled out and slightly to one side until you can see the black light tube starter.

REMOVE THESE SCREWS O Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the black light tube starter, reverse this procedure. . The black light tube mounting bracket assembly may be replaced at this time by simply disconnecting it from its power cable and removing it from the game. . To reinstall any of the above removed items, simply reverse this procedure.

  • Upright

BLACK LIGHT PROTECTOR

CONTROL PANEL SUPPORT BRACKET

Figure 3-17 Servicing Control Panel Black Light — Upright

Page 25

IV. Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual.

As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as weil. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet

After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedutes. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanieéal failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is. making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will teli you if there is a continuous line all the way to the credit circuit

Page 26

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and Credit Circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. !f not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to Operate properly. if the line voltage drops too low, a Circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly wnen starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes iocation owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wail receptacle. \f it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occurin areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scaies. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one byone until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typicaily, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. if a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of inputit is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND orto pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 27

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM’s contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LS! microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors: The Z-80 is fully software compatible with the popular 8080A CPU. Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:

  • CPU (Central Processing Unit)
  • Memory
  • Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it outto another peripheral device. Note that the Zilog component set includes the CPU and various general purpose |/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic. n
Page 28

General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt responseis required, one set of general purpose registers andan accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internaily the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)

Subtract Increment

Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.

_2730
mww=-——> A,

Ls AY

a1932

MREQ «<¢——_+| >——™ A,

system _/ ond|pS A,
CONTROL \ 552cy
wRaw———

36 Ae RSH 2% [Ze a, | 33. a, ADDRESS __ BUS

rat«|Z-80 CPUae a,

| # a,,

cpuwar—% olae An

CONTROL [.*

int=-—8_ 9—e
ro7J 4. Ane

bd _ [>-—— A, RESET = ye

CPU < oom a | BUS ausak «2 CONTROL ~ 14 jet 0, 15, D.

o6| Pane O,

—| 2

svSsae DaDATA
GND—=beim 0,BUS

be Ds fet Z-80 PIN CONFIGURATION is

4-4

Page 29

Ao-Ais (Address Bus) Tri-state output, active high. Ap-A;s constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. A, is the least significant address bit. During’ refresh time, the lower 7 bits contain a valid refresh address.

Dy-D, (Data Bus) Tri-state input/output, active high. Do-D, constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.

M, (Machine Cycle one) _ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid I/O address for a I/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) _ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.

4-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.

HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.

INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the interna! software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT. and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 30
  • Set Register | = 00H
  • Set Register R =00H
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signa! is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.

CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.

Page 31

MCR II SYSTEM P.C. BOARD JUMPER OPTIONS

VIDEO GENERATOR P.C. BOARD

[* | * | | * | * | f+ | # | p# [| Pe [*[*[#[e[e) ee Pree zroe we Te [Le te |e [|

MANUFACTURER | EPROM NO.

NOTE: JUMPER OP- NUMEROUS MFR'S | 202 |e | a | TION FOR PROGRAM NUMEROUS MFR'S | 2732] we | # ROMs ONLY.

MANUFACTURER [EPROM NO. | swt swe? | NUMEROUS MER'S

NUMEROUS MER'S

# = LEAVE JUMPER WIRES WHERE THIS SYMBOL “#” APPEARS

%* = CUT JUMPER WIRES WHERE THIS SYMBOL “*” APPEARS.

The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the C.P.U. P.C. Board used in the MCR || System has 6 jumper wires, and the Sound I/O P.C. Board used in the MCR II System has 2 jumper wires. All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut.

The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wires number. If there is a “#" under a jumper wires number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.

Page 32

V. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150

COIN DOOR MAINTENANCE

METAL COIN ACCEPTOR MECHANISMS Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

1, Make sure the power to the game is off.

  • Unlock and open the coin door.

TO REMOVE PUSH LATCHES DOWN

PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781

  • Remove the coin acceptor mechanism as shown in Figure 5-1. O Push down on the two spring loaded latches. 0 While holding the latches down, pull the top of the coin acceptor mechanism toward you. O Release the latches and lift out the coin acceptor mechanism.

5 ata pears

PUSH MECHANISM IN

Figure 5-1 Removing and Replacing the Coin Acceptor

Page 33
  • Clean the magnet of all foreign particles. See Figure 5-2. O This may be accomplished by swinging the gate open as shown in the above figure.
  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) D Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.

O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. D Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 5-2 Cleaning the Metal Coin Acceptor

  • To lubricate the coin acceptor: Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 5-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
  • WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 5-1. C Place the two pegs at the coin acceptor's base into their retaining slots. 1 Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

UNDERSIZE LEVER

“E” RINGS

CRADLE

Figure 5-3 Lubricating the Metal Coin Acceptor

5-2

Page 34

SQUEEZE PINS TOGETHER TO UNLOCK

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 5-4 Opening the Plastic Coin Acceptor

PLASTIC COIN ACCEPTOR MECHANISMS

The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanisms(s) as shown in Figure 5-1. Push down on the two spring loaded latches. O While holding the latches down, puli the top of the acceptor mechanism toward you. 0 Release the latches and iift out the mechanism. 4, Squeeze the two pins indicated in Figure 5-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry.

5-3 O Reassemble the mechanism (it never needs lubrication).

  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 5-5. O Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 5-6 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.
Page 35

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

MAGNET

SS?

SLIDE MAGNET TO EXTREME RIGHT (AS. SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

$e

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT,

Figure 5-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters

5-4

Page 36

PLEASE NOTE:

THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

Introduction: (How to use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but a more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, itwould be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings

6-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYMPTOM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it. Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part. . Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is ail there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Bally Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 37

Symptom Diagnosis

|. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). C Bad yoke. C Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. 0 Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. O Open width coil. O Open part in horizontal output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad Component in output circuitry. C. Vertical linearity or damper contro! needs adjustment. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: Interface color transistors. Color output transistors. Cracked printed circuit board (neck Board). Color circuits. Video input jack. Defective picture tube. ™mMODOD>

. Picture not bright enough: A. Weak emission from picture tube. . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit). B. Bad component in monitor's power supply.

6-2 10.

11.

12.

13.

14,

15.

16.

17.

18.

19,

20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator in the IC, vertical sync. transistor, or circuit. B. No sync from logic board. C. Three pin sync. jack is loose or plugged in wrong. Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal syne needs adjusting. B. Magnetic or electromagnetic interference. Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke. No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizonta! amplifier and output. C. Flyback transformer (high voltage unit). No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.

No as voltage; check:

For AC input to the “flyback” Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moom>

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 38

|. Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).

. Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts’ peak to peak, the picture tube has weak emission.

. Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor. B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

  • Can't adjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. B. Picture tube defective. C. Nearby equipment is electromagnetically inierferring. OD. The poles of the earth are pulling off the purity — see “A” above. E. Poor focus or width of picture. Make sure you have the correct CRT number for that brand of monitor. mm

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

ALYY YW INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

OL

FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 39

COLLECTOR Te COLLECTOR Ko BASE ———~ BASE————- EMITTER es EMITTER me

NPN TRANSISTOR PNP TRANSISTOR

“VW

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+ +

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

rh gw GROUND

Page 40
  • Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
  • Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 voits’ peak to peak, the picture tube has weak emission.
  • Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor. B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
  • Can't adjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. Picture tube defective. Nearby equipment is electromagnetically interfering. The poles of the earth are pulling off the purity —— see “A” above. Poor focus or width of picture. Make sure you have the correct CRT number for that brand of monitor. ™m 0 OD

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SYY OW INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(4+) ANODE

ZENER DIODE \| U1 i

IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

nO a FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 41

COLLECTOR a COLLECTOR a

BASE ———— BASE ————-

EMITTER Tl EMITTER TY

NPN TRANSISTOR PNP TRANSISTOR

WW

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+ +

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

rh 4g & GROUND

6-4

Page 42

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad: 1, Semiconductors (like transistors, diodes, and integrated circuits).

  • Fusible resistors.
  • Electrolytic capacitors.
  • Resistors.
  • Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 23,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors) or ICs, yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first it implodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in ail directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole.
IMPORTANT! The side brackets of the monitor are chassis ground as is the aquadag, the picture tube’s dark conductive coating. BUT, on the ZENITH MONITOR there are metalic mounting parts which ARE NOT chassis ground. Discharging the CRT to these will damage the monitor!

6-5 Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube. To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.

Page 43

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite it it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on abad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the

voltage goes up and so does the resistance. If you are

sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice,

constant, smooth voltage so that the monitor circuits

don't jump around. And this is what happens when you see a wavy picture. There is AC creeping

6-6 through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or none atall. Some circuits receive voltages that are higher than what the power supply should put out. But they come irom the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 44

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, {ike a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 23,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors) or ICs, yoke terminals, and other high power components when the monitor is on,
WARNING: That picture tube is a bomb! When it breaks, first itimplodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the !ong, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole.
IMPORTANT! The side brackets of the monitor are chassis ground as is the aquadag, the picture tube’s dark conductive coating. BUT, on the ZENITH MONITOR there are metalic mounting parts which ARE NOT chassis ground. Discharging the CRT to these will damage the monitor! as en Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personne!. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube. To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. if the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voitages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. if everything (ooks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.

Page 45

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. Anormal transistor wili read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistanily infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. tis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuitin case some componentis messing up the ohmmeter reading.

NOTE: DONOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up Current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be maljunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. Buithey come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 46

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an Orderly jigsaw puzzle, but so fast that you can’t see the electron beams for each color Painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its sync section. The Zenith monitor (CD19MXRF06) also uses an |C for the sync processing. Wells Gardner uses HA11423, Electrohome uses HA11244, and Zenith uses 221-175 (their part number). These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second.

Aiong the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the veriical and horizontal of all monitors, there are variable resistors that change the speed of the oscitlators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acarand next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn't appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer, THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can't meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 24,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply. COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green on

Page 47

Wells Gardner and Electrohome monitors. Zenith monitors have all three: red, blue and green. The Wells Gardner and Electrohome monitor have another variable resistor in their emitter part of their color output transistors. These “cutoff controls” vary the amount of A.C. signal that the transistor amplifies and sends to the cathodes of the picture tube. The Zenith monitor has its cutoff controls in the interface section to vary the amount of signal going to the output transistors. The more signal, the more color. If you think this is confusing, here is another little hitch. The Electrohome and Zenith monitors both have the actual A.C. picture information signal going through the emitters of the color output transistors. The Wells Gardner has the A.C. signal going to the base of the transistors. The blanking and beam limiting signals which come from the blanking and beam limiting transistors in the interface section go into the color output transistor base in the Electrohome and Zenith monitors, but enters into the emitter of the Wells Gardner monitor's color output transistor. Should you feel adventurous enough to look at this signal on an oscilloscope, it should look like a square. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture. PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage and turns off the horizontal oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don't be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's C501 and emitter of X04 for the Electrohome monitor. Check the $5 volt test point (located near the “flyback”) for the Zenith monitor. The Wells Gardner monitor doesn't use this circuit, but an open in the horizontal section could cause the monitor to appear off, yet still have power supply voltage flying around. Here are the voltages you should receive: Wells Gardner = 130VDC Electrohome 120VDC Zenith = VDC The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO7-FBO or GO07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.

6-8 THE PICTURE TUBE (OR CRT) —

ATTENTION! For information on picture tube replacement types, go to the last section, “PICTURE TUBE INTERCHANGEABILITY”.

The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. A defective cathode may cause the particular color it handles to be missing. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with is to find the manufacturer's name or model number printed on the chassis or chassis base. But what if the monitor was in a Texas dust storm or buried in volcanic ash and this information is no longer there? Fear not! Each monitor has its own peculiarities and the following should help to identify them: The ELECTROHOME G07-904 (19”) and G07-902 (13") have their horizontal and vertical processing IC hidden under a silver can. A shiny metal top behind the “VERTICAL HEIGHT” and “HORIZONTAL FRE- QUENCY” control prove this is an Electrohome monitor.

Page 48

The WELLS GARDNER K4906 (19"’) and K4806 (13”) have their horizontal and vertical processing !C out in the open directly behind the “VERTICAL HOLD” control, The ZENITH CO19MXRFO6 (19") monitor has its horizontal and vertical processing {C way in back by the picture tube. The monitor also has large white cables going from the main board to the neck board.

K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as anormai T.V. would be) for any video game that may need these lines to fit the picture on the screen. Moving the Control may distort the top part of your picture (or the side, depending onthe game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electronome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the * controls. The Zenith monitor has a 95 volt adjustment control. It is green and located behind the jack labeled 3D3. To discourage you from moving it, Zenith has placed a little glue on top of this control.

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance.
  • You CAN swap any capacitor between monitors that has the same capacitance and voltage rating.
  • You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.
  • You MAY BE ABLE to swap picture tubes between monitors. in the past you could swap any picture tube, but due to rampant engineering changes and new monitor models being introduced, you would need a computer to keep track of what could be swapped. For more information on this subject, go to “PICTURE TUBE INTERCHANGEABILITY”.
  • You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-802) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTER- CHANGEABLE!
  • You CAN change any of the parts between the GO07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube.
Page 49

If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.

Picture Tube Interchangeability

13" MONITORS

There are currently two 13” monitors being used: the Wells Gardner K4806 and the Electrohome G07-902. The picture tubes used are NOT interchangeable. The pins on the neck of the CRT will not fit in the socket should you use the wrong CRT.

Here is a chart for all the 13” color monitors Bally Midway uses. ELECTROHOME — G07-902 — 370ESB22 WELLS GARDNER K4806 —370KSB22

19” MONITORS Here it gets a little tricky. All of the picture tubes will fit no matter which is used. But if you use the wrong one, you will have problems with purity and/or dynamic convergence. Purity trouble means that the color won't be true. If you turn up the color control for one color, instead of seeing that solid color it will show blotches or blobs of other colors on the screen.

Trouble with dynamic convergence means that there will be color fringing around solid lines at the edges of the screen.

The only way to ensure that you avoid these problems is to get the right picture tube or the right substitute.

Here is a list of the 19" monitors and the CORRECT CRT numbers.

ALL ELECTROHOME G07-904 — 19VMNP22 RCA 19VMJP22 RAULAND 510UJB22 HITACHI

WELLS GARDNER K4906 — 19VLTP22 RCA 19VMLP22 ZENITH 19VMKP22 PHILLIPS

ZENITH CD19MXRFO6 — 19VMLP22 ZENITH 19VLTP22 RCA 19VMKP22 PHILLIPS The factory recommended CRT type could change in the future for one reason or another, but the listed picture tubes will work. As a matter of fact, you can call another picture tube company to see if they have a replacement number to recommend...but caveat emptor — let the buyer beware.

Page 50

Monit

Page 51

Power Supply Voltage and Symbols

Symbol | Voltage Operating Circuit ® 15V | Vert. Osc. Syne Blanking CRT Cut-Off

e 130V_ | Horiz. Ose Horz. Drive Horz. Output Vert. Output

© 175V_ | Video Output

AVIDIV 200uSECIDIV 20VIDIV 10USECIDIV

TP-31 DC COUPLED 402-3 BOTTOM LINE =0 VOC

2V/DIV 200MSECIDIV SVIDIV 26uSECIDIV

LC. 301, PINS F

soon

AVIDIV SMSECIDIV AVIDIV 20u SECIDIV

TP-82 ‘TP-31, AC COUPLED

20VIDIV SMSECIDIV 1VIDIV 200uSECIDIV

LC. 301, PIN 13, NEGATIVE SIDE OF C303

1VDIV 200uSECIDIV 2VIDIV SMSECIDIV

6-12 351 COLLECTOR

SASAALRLALLLAMLL 18° 9 19” COLOR MONITOR SCHEMATIC DIAGRAM MODELS 19K 4901, 19K 4906, 19K4951, 19K4956

SERVICE TECHNICIAN WARNING X-RAY RADIATION PRECAUTION:

THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS

4 ESSENTIAL FOR X-RAY RADIATION

_ PROTECTION. f FOR REPLACEMENT PURPOSES, USE | ONLY TYPE PARTS SHOWN IN THE bit ‘

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM PONENTS ONLY WITH MANUFAC- TURER'S RECOMMENDED PARTS. AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L’APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.

rosser | “coo WEF gh See boat LF

eons Shey th 9

  • 2scil vat ages) 28 B48 [Hele p O.S/DIV SMSECIDIV 2gciaise/ aR 22 __ 2SASBavT™M pw

O.S/DIV 20u SECIDIV

1.C. 301, PIN 15,

180." \780v

FB anasy a Rae isk) Sk SP 2) SPIE ATS OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. If the waveforms are observed on the oscilloscope with @ poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.

be bur 28C2068.8/L8eK 25020681 8/. 8K 25C20688/.55K| 2SCISIABVE/CVE 2SCIBISBVELVE 28CISI4BVC/CVC

ak weve)

Rats 2aincva)

[R.CUTOFF} [G.CUTOFF)

R358

eaxusrs) odeoaea . | BIOBK case

SYNC AMP VOSC HOSc wana23

aa ey 151888 2VIDIV 10uSECIDIV A

F

ypeswscecmmmnemmneeage|

co etomsermnnnnnmnenne

1VDIV 2MSECIDIV Da0oaigur HORCENTERING]

TEi808 foes ay unt Lie a 382 (HOR.SIZE)

K4901D, K4906D, K4951D 5833 K4956B .

Page 52

REPLACEMENT PARTS LIST MAIN BOARD (CONT.

This monitor contains circuits and components included specificallyRef. No.Part No.DescriptionRet. No.Part No.Description

for safety purposes. ~

For continued protection no changes should be made to the origina!CAPACITORS (CONT.)SEMICONDUCTORS (CONT.)
design, and components shown in shaded areas of schematic, or A ®A oemae470 uf, 500V Ceramic308FacetedTanelstor NEM zecietsga
fiC501203X1810-10.1 uF, 125V Mylar73181-523ransistor (NPI
On parts list should be replaced with exact factory replacement parts.4 502202X7050-2821800 pF, 500V Cerantic208200x3181-523Transistor (NPN) 28C1815GR
The use of substitute parts may create a shock, fire, radiation or other4.503202X7810-2142200 pF, 125V Ceramic0209200X3181-523Transistor (NPN) 28C1851GR
hazard. Service should be performed by qualified personnel only.Ac504202X7810-2142200 pF, 125V CeramicQ210200X3181-523Transistor (NPN) 28C1851GR
505203X0220-075560 uF, 200V ElectrolyticQ301200X3181-523,Transistor (NPN) 2SC1851GR
C508203x0040-03422 uF, 160V ElectrolyticQ302200X3207-306Transistor (NPN) 28C2073LBGi.i
507203X0041.05747 uF, 160V ElectrolyticQ303200x3207-306Transistor (NPN) 28C2073LBGL:
MAIN BOARD701203x0019.0921000 UF, 25V Electrolytic351200X3248-217Transistor (NPN) 28C24828K
C702203X0634-06140 uF, 100V ElectrolyticQ352200X4589-802Transistor (NPN) 2SD898B
hot.art NoDesziptienapan NescrionC703202X7050-248,1000 pF, 500V Ceramic4020200X2300-033,IC HA11423
jet. No.;2.No.artNo.scription.10501200X2600-183,IC STR381
  • SEMICONDUCTORS
203201X2010-159Diode, 1S2076-27
RESISTORSRESISTOHS (CONT)bao2orxeoto 189Diode 207627a,GANSEORMERS & COILS,
203X6500-645,1K Ohm, 5%, 1/4W CarbonR369203X5602-329680K Ohm, 5%, 1/2W Comp.205201X2010-159Diode, 1$2076-27352201%5000.083Coil, Nene coe
203X6500-52330 Ohm, 5%, 1/4W CarbonR370203X6501-00233K Ohm, 5%, 1/4W Carbon0206201X2010-159Diode, {$2076.27L701614X0004.007Coil, Adg.
203X6500-405100 Ohm, 5%, 1/4W CarbonR371203X9014-584Ohm, 5%, 1W Metal Oxide0207201X2010-159Diode, 1S2076-27735BpaKts00 80.Trankiomier, Hor rive
203X6700-327100 Ohm, 5%, 1/2W CarbonR372203X9101-11912K Ohm, 5%, 1W Metal Oxide208201X2010-159Diode, 1$2076-27Aw 1382200X9720.301HVUnit Mal
203X6700-421270 Ohm, 5%, 1/2W CarbonR375203X6700-7636.8K Ohm, 5%, 1/2W Carbon208201X2010-159Diode, 1$2076-27
203X6500-540390 Onm, 5%, 1/4W CarbonR376203X9104-404270 Ohm, 5%, 2W Metal OxideDaas201X2010-165Diode, 1SS81MISCELLANEOUS
340X2201-934200 Onm, 5%, 1/4W CarbonR377203X6500-447150 Ohm, 5%, 1/4W Carbon0302201X2010-159Diode, 1$2076.27
203X6500-540380 Ohm, 5%, 1/4W CarbonF378203X6500-88640K Ohm, 5%, 1/4W Carbon0303201X2010-159Diode, 1S2076-27AF501204X7120-073Fuse, 4 Amp. 125V
340%2201.934200 Ohm, 5%, 1i4W CarbonR979203X6500-88610K Ohm. 5%, 1/4W CarbonD304201K2120-009Diode, RHVsa0n206X5008-632Recep W Wire 3P-M-BG
203X6500-540390 Ohm, 5%, 1/4W CarbonR380203X6500-865,8.2K Onm, 5%, 1/4W Carbon0305201X2120-009Diode, RH-IVP20t204X9600-466Plug, PWB 3P-J
340X2201-934200 Ohm, 5%, 1/4W CarbonR381203X6500-7242.2K Ohm, 5%, 1W Metal Oxide0306201%2010-159Diode, 182076-27202204X9601-477Plug, PB 6P-0
203X6500-6451K Ohm, 5%, 1/4W CarbonR383203X9014-387150 Ohm, 5%, 1W Metal Oxide40501201X3120-216Diode, RM-1AVPaot204X9600-298Plug, PWB 4P-B
203X6501-126100K Ohm, 5%, 1/4W CarbonR502203X6500-88640K Ohm, 5%, 1/8W Carbon40502201X3120-216Diode, RM-1AVP501204X9600-249Plug, PWB 2P-8
203X6500-6451k Ohm, 5%, 1/4W CarbonR503204X 1700-535150 Ohm, 5%, 15W Metal Oxide40503201X3120-216Diode, RM-1AVP601204x9800-304Plug, PWB 4P-C
203X6500-405100 Ohm, 5%, 1/4W CarbonR504203X9014-26747 Ohm, 5%, 1W Metal Oxide0504201X3120-216Diode, RM-1AVTHE01201x0100412Thermistor
203X6500-6451K Ohm, 5%, 1/4W CarbonR505203X6501-2092.2K Ohm, 5%, 1/4W CarbonBoreParpiowes oa
203X6501-126400K Ohm, 5%, 1/4W CarbonR506203X9104-10515 Ohm, 5%, 2W Metal Oxide‘iode,RM-
203X6500-6451K Ohm, 5%, 1/4W CarbonR507203X5602-185330K Ohm, 5%, 1/2W Comp.0701201X2130-234Diode, RU-2VFINAL ASSEMBLY PARTS
203X6500-405100 Ohm, 5%, 1/4W CarbonA*R601204X 1625-0583.3 Ohm, 5%, 10W WW.0702201X2120-009Diode, RH-VAk 88X0138-50619VLTP22 Pix Tube
209X6500-7623.3 Ohm, 5%, 1/4W CarbonR701203X9105-1412.2 Ohm, 5%, 2W Metal Oxide201200X3181-523205X9800-158Lateral/Purity Assembly
203X6500-6940 Ohm, 5%, 1/4W CarbonR702203X6206.4412.2 Ohm, 5%. 1/2W CarbonQ202200X3181523Transistor (NPN) 2SC1815GRA ee 202K1111-201Yoke Deflection
203X6500-16910 Ohm, 5%, 1/4W CarbonVR201204X2070-0722K Ohm-B Semi-Fixed203200X4056-260Transistor (PNP) 2SA562-V-TM204X9301-255CRT Socket
203X6500-16940 Ohm, 5%. 1/4W CarbonR301304x2070-0845K Ohm-B Semi-Fixed204200X4056-260Transistor (PNP) 2SA562-Y-1M281X5004-262Automatic Degaussing Coil Unit
203X6501-04447K Ohm, 5%, 1/4W CarbonVR303204X2070-055500 Ohm-B Semi-Fixed0205200X4056-260Transistor (PNP) 25A562-Y-TM
203X6500-6454K Ohm, 5%, 1/4W CarbonR351204x2070-0722K Ohm-B Semi-Fixed
203X6700-421270 Ohm, 5%, 1/2W CarbonR352204X2070-0722K Ohm-B Semi-Fixed

203X6500-863 8.2K Onm, 5%, 1/2W Comp. 203X6500-863 8.2K Ohm, 5%, 1/2W Comp. 203X6500-863 8.2K Ohm, 5%, 1/2W Comp. 203X6500-468 180 Ohm, 5%, 1/4W Carbon 3402820934 82 Ohm, 5%, 1/4W Carbon CAPACITORS

340%2820-93482 Ohm, 5%, 1/4W Carbon201203x0014-0881000 uF, 16V, ElectrolyticNECK BOARD
340X2820-93482 Ohm, 5%, 1/4W CarbonC202202X7200-084330 pF, 500V, Ceramic
203X6500-508270 Ohm,5%, 1/4W CarbonC203202X7200-043220 pF. 500V, Ceramic
203X6500-8638.2K Ohm, 5%, 1/4W CarbonC204202X7200-043220 DF, S00V, CeramicRESISTORSCAPACITORS
203X6500-8638.2K Ohm, 5%, 1/4W CarbonC205203X0014-076470 UF, 16V, ElectrolyticR401203X6000-729220 Ohm, 5% 1/4W CarbonC401202X7050-2691200 pF, 500V Ceramic
203X6500-7242.2K Ohm, 8%. 1/4W Carbon206203x1810-1490.1 uF, 125V MylarR402203X6500-540390 Ohm, 5% 1/4W Carbon402202X7050-248,1000 pF, 500V Ceramic
203X6500-8426.8K Ohm, 5%, 1/4W CarbonC207349X2232-109(022 uF, 100V MylarR403203X6000-661820 Ohm, 5% 1/4W CarbonC403202X7050-248,1000 pF, 500V Ceramic
203X6003-2017.5K Ohm, 2%, 1/4W Carbon6301203x0014-065320 uF, SOV ElectrolyticR404203X6000-729220 Ohm, 5% 1/4W CarbonC404202X7050-2821500 pF, 1.5KV Ceramic
203X8500-8255.6K Ohm, 5%, 1/4W Carbon302203x 1600-5630.033 uF, 50V MylarR405203x8500-540390 Ohm, 5% 1/4W CarbonC405202X7050-483,0.01 uF, 500V Ceramic
203x650096522K Ohm, 5%, 1/4W Carbon6303203X0629-0373.3 uF, 50V Electrolytic406203x6000-661820 Ohm, 5% 1/4W Carbon
203X6500-98839K Ohm, 5%, 1/4W CarbonC304203X1600-3660.068 pF, 50 MylarR407203X6000-729470 Ohm, 5% 1/4W Carbon
203X6500-7623.3K Ohm, 5%, 1/4W CarbonC306203x0412-01222 uF, 16V TantalR408203X6000-998270 Ohm, 5% 1/4W CarbonSEMICONDUCTORS
203X9014-7414.7K Ohm, 5%, 1/4W Carbonc307203X 1600-6340.033 uF, 50V MylarR409203X6000-661820 Ohm, 5% 14W Carbon401200%3206-800Transistor (NPN) 2SC2068LB
204X 1450-5371K Ohm, 5%, 5W CarbonC308203X0025-1743.3 uF, 50V ElectrolyticR410203X9104-82415K Ohm, 5% 2W M.O. Forming402200X3206-800Transistor (NPN) 2SC2068LB
203X6500-481220 Ohm, 5%, 1/4W Carbon309203X1207-1000.068 uF, 100V PPRatt203X9104-82415K Ohm, 5% 2W M.O. Forming403200X3206-800Transistor (NPN) 2SC2068LB
203X6500-16910 Ohm, 5%, 1/4W Carbon310203x0629.06140 uF, 100V ElectrolyticR412203X9104-82415K Ohm, 5% 2W M.O. Forming
203X6500-7623.3K Ohm, 5%, 1/4W CarbonC311203X0041.02510 uF, 160V ElectrolyticRa13203X6000-9982.7K Ohm, 5% 1/2W Comp.
203X6700-10712 Ohm, 5%, 1/2W CarbonC312202X7050-2484000 pF, 500V CeramicRata308x6000-9082.7K Ohm, 5% 12W CompMISCELLANEOUS
2036500-540390 Ohm, 5%, 1/4W CarbonC313203x0040-05247 vF, 160V ElectrolyticR415,(6000-998.7K Ohm, 5% 12W Comp.:
203X6500-6454K Ohm, 5%, 1/4W Carbon314303X1201.2650.033'uF 200V PP”R416203X9105-1542.2 Ohm, 5% 2W Metal OxideoepeeredLiga
203X6501-00233K Ohm, 5%, 1/4W CarbonC315203x0629.0231 uF, 50V ElectrolyticR419203X6500-7412.7K Ohm, 5% 1/4W CarbonPaes04x oe00 DaTPl Pine
203X6501-224270K Ohm, 5%, 1/2W CarbonC351203x0629-0231 UF, 50V ElectrolyticR420203X6500-7412.7K Ohm, 5% 1/4W Carbonratooxoeot 020Bik BWe ee
203X6500-88640K Ohm, 5%, 1/4W CarbonC352203X0619-04547 uF, 25V ElectrolyticR421203X6500-7412.7K Ohm, 5% 1/4W CarbonUg,|
203X6500-88640K Ohm, 5%, 1/4W CarbonC353303x1190.0180.0082 pF, 50V Mylar-PPR401204X2115-014500 Ohm, -B Semi-Fixed
203X6500-7853.9K Ohm, 5%, 1/4W CarbonC354203X0619.04547 uF, 25V ElectrolyticR402204X2115.01400 Ohm, -B Semi-Fixed
203X6501-08668K Ohm, 5%, 1/4W CarbonC355,203X1600-3660.0068 pF, S0V MylarVR403204X2115-0065K Ohm, -B Semi-Fixed
203X6500-7623.3K Ohm, 5%, 1/4W Carbon356202X7050-4830.01 uF, S00V CeramicvRa04204X2115-0065K Ohm. -B Semi-Fixed
203X9205-1436.8K Ohm, 5%, 3W Metal OxideC359202X8065-606100 pF. 500V CeramicVR405204X2115-0065K Ohm, -B Semi-Fixed
203X5601-87856K Ohm, 5%, /2W Carbon360202X7050-3660.0033 pF, 500V Ceramic
203X6500-561470 Ohm, 5%, 1/4W CarbonC361202X7050-483,0.01 uF, 500V Ceramic
203X6500-48610K Ohm, 5%, 1/4W CarbonC362202x7203-0320.01 uF, 50V Ceramic
203X9014-6451.8K Ohm, 5%, 1W Metal OxideD%C363203X1270-9118700 pF, 1.5 KV PP
204X1527-7513.9K Ohm, 5%, 7W Metal OxideC365203X1201-2650.33 uF, 200V PP
203X6500-24622 Ohm, 5%, 1/4W Carbon6366203X0019-02622 uF, 28V Electrolytic
203X6501-00233K Ohm, 5%, 1/4W Carbon367202X8065-1626 pF. 500V Ceramic
203X6500-88610K Ohm, 5%, 1/4W CarbonC368202X7203-0320.01 UF, 50V Ceramic
203X5602-185330K Ohm, 5%, 1/2W Comp.C372203X1207-1250.1 uF. 100V PP
Page 53

Blue 2MUeN RED XI01.XIO3 ond XI05 VIDEO AMP. 25C454C ; Xbeckton ong koe VidEO_ AME g8u6r3e Sa SEEE STE

—_Bezel or ascisiav:

fr201x302,x500,x306 | wel F SYNC AMi | j2SC454C or 98CI68S |

X901 POWER DRIVE 25¢ 2688 X902 ERROR AMP —2SC1890 | Sdoca, asciasa | | Bas R REGULATOR ro

eo, nue Ber owe

Pree:midBH»-

wor | rT] aie bie Tae PPPOE 9D) Fite] ei ic caw cu ar ae waar were] f ws anf i fr — fraase Det] [onc] feave Format ry m=O Kota Pn bee) Yond’ Hav Sc] | xso1 mu

Laaxfresco)Schematic Notes
|338)s4aUnless otherwise specified
ng0°sey)etaResistance: (1) (K-*KQ, M*MQ), 1/4 (W) carbon resistor
2M ome|Capacitance: 1 or higher-» (pF), less than 1-> (yF)
| ret 888% ure| ihworking voltage -» 50 (V)
ean|ceramic capacitor

t Inductance: (v H)

ae=Yor erin YOKE!Electrolytic Cap: Capacitance Value (y F)/working voltage (V),
roSra.pared taeae|te aeNP — non-polar (or bipolar) electrolytic cap.

Ba BS ASSY bat er Tar BB EP icn *— Refer to the parts list for additional component information.

4701 XRAY PROTECTORBeeisd7 BE, ascasrv SSb8e0 oru-n038i=indicates test Point connectionF
algams28C454C or 251685B5c26ii or 28¢z6.08K 250869 w“memes7hindicates chassis ground unless otherwise specified

Lead 280620 ee hae Hz indicates cycles per second wom For safety purposes (and continuing reliability) A replace all components marked with safety syrnbol with identical type.

NOTE: FR — fusible resistor ie 00-4147-04 Parts identification on circuit boards: Go7-CBO e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)
Page 54

REPLACEMENT PARTS LIST—ELECTROHOME 19" MONITOR oe

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics

DO N | important to safety. i i L T degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CRCarbon ResistorC Cap.
Comp. RComposition ResistorM Cap
OMROxide Metal Film ResistorE Cap.
VRVariable ResistorBP E Cap.

MFR Metal Film Resistor

CMF RCoating Metal Film ResistorMM Cap.
UNF R:Nonflammable ResistorPP Cap.
FR:Fusible ResistorMPP Cap.

PS Cap. Tan. Cap.

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, ail parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbo! Description Main PC.B. Assy CRT Socket PC.B. Ass'y Purity Shield Ass'y

Outside of the P.C.B. Ass'y Symbo! Description Picture Tube 19" A A\Deflection Yoke PC Magnet A A\Flyback Transf. Aa AHVR ROS UNF Resistor 2202,25W K Co4 C Capacitor 150pF, AC1.5KV X01 Si. Transistor X02 Si. Transistor sc Screw #8-% Sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip—P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3) Part Number SU-7133A SU-3032A 07-220083-03

Part Number 17-7198-03 A29779-D=21-141-07 A75034-B=29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005, 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 98-449-02 39-1233-01 Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Ner-Polar) Electrolytic Capacitor Metalized 'ylar Capacitor Polypropyiens Capacitor Metalized PP Capacitor Polystyro! Capacitor Tanta! Capacitor

Purity Shield Ass’y. Parts List

Symbol

D911, D912

cet R921 Description Part Number Degaussing Coil 21-1007-30

Rectifier 1 Amp 600V (2) 28-22-27 Pin Terminal (2) 34-708-01 Pin Termina! Housing 34-709-01 Purity Shield (2 pes.) 35-3847-01 Purity Shield (2 pes.) 35-3847-02 Capacitor 100nF 10% 400V Resistor, Wirewound 332, 4W Fire Retardant Term. Strip 4 Lug 48-171544-62 42-113301-03 34-492-09

CRT Socket P.C.B. Ass'y (SU-3032A) Parts List

Resisiors Symbol R3105 R3106 R3113 R3114 R3115 R3116 R3117 R3118 R3119 R3120 R3121

Capacitors Symbol C3107 C3108 Description Part Number

vR200QVZ3234-022
vR200QVZ3234-022
VvR5KQVZ3234-053
VvR5KQVZ3234-053
VvR 5KQVZ3234-053
OMR10K22W JQRGO29J-103
OmR10K22W JQRGO29J-103
OMR10KQ2WJQRGO29J-103
Comp.R3.3KQ%W KQRZ0039-332
Comp.R3.3KQ%W KQRZ0G639-332
Comp.R3.3K2%W KQRZ0039-332

Description Part Number

ECap.10uF 250VAQEWS53EA- 106
CCap.1000pF DC1400VPQCZ9001-102M

CRT Socket P-C.B. Ass'y (SU-3032A) Parts List (Cont.)

Coils Symbol 13101

Semiconductors Symbol 3101 X3102 X3103

Miscellaneous Symbol A Description Peaking Coil

Description Si. Transistor Si. Transistor Si. Transistor

Description ACRT Socket

Main PCB Ass’y (SU-1133A) Parts List Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AR1503 R1504 R1509 R1512 R1514 R1515, R1522 R1523 R1528 R1534 VR1501 A\R1703 AR1704 AR1901 R1902 R1903, R1904 R1905 AQ1908 AR1909 R1910 AFR1901

Capacitors Symbol C1301 C1402 C1407 C1444 C1412 C1508 Ac1512 AC1513 Aci514 C1515 C1520 C1523 C1524 AC1531 AC1532 C1904 C1905 Description

VvR2002

VR 2002

CMFR6821WJ
OMR3.3KQ1WJ
OMR27KQ1WJ
OMR12ke2WJ

VR 10KQ AF = R 6822WK

ACMFR=11.8KQY%W+1%
VvOR5KQ
OMR10K22WJ

OM R 62KQ2WJ

OMR82022WJ
CMFR8201WJ
CMFR4701WJ
OMR68Q2WJ
OMR39021WJ

ZN oR ZN OR

ACMFR392%W+1%
ACMFR7.68KQY4W+1%

AsPosistor

UNFR207WK
CMFR4.703WJ
OMR10KQ2WJ
OMR18K21WJ
ACMFR472%W+1%

VR 2ka

ACMFR2.74KQYW+1%

AF = -R 22024WK

Description BPE Cap. 3.3uF 50V A Tan Cap. 2.2uF 16V K E Cap. 4.7uF 6.3VA E Cap. 100uF 160V A E Cap. 3.3uF 160V A PP Cap. 5600uF 50V J APP Cap. 2000pF DC1500V J APP Cap. 2000pF DC1500V J APP Cap. 2000pF DC1500V J PP Cap. 0.53uF DC1200V J BPE Cap. 3.3uF 50V A E Cap. 1uF 160VA M_ Cap. 0.1UF 200V K APP Cap. 2000pF DC1500V J APP Cap. 1500pF DC1500V J E Cap E Cap. 10uF 250V A Part Number QQL043K-101

Part Number 2SC1514VC 2SC1514VC 2SC1514VC

Part Number A76068

Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRGO19J-332 QRGO19J-272 QRGO26J-123Z QVZ3230-014 QRHO024K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRGO26J-822Z QRGO26y-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO19J-391 ERZ-CO5ZK471 ERZ-C05ZK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRGO26J-1032Z QRGO19J-183 QRV122F-470Z QVPS5A0B-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-3352 QEES1CK-225B QEW51JA-475 QEWS52CA-107 QEWS2CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS2EA-106 Main PCB Ass'y (SU-1133A) Parts List (Cont.)

Coils Symbol L1502 11503, 1504

Transformers Symbol T1501 T1503

Semiconductors Symbol 1C1501 X1101 X1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 x1402 X1501 X1901 X1902 D1101 D1102 D1103 D1301 D1401 B1402 D1503 01504 D1505 D1506 D1507 D1508 A\D1701 AD1901 AxD1902 4A\D1903 A\D1904 AD1905

Miscellaneous Symbol AAF1901 AF1902 Description Linarity. Coil Width Coil Heater Choke

Description Hor. Drive Transf. Side Pin Transf.

Description Ic Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Diode Si. Diode Si. Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AZener Diode ASi. Diode ASi. Diode ASi. Diode ASi. Diode AdZener Diode

Description AsFuse 1.25A AUL Fuse 3A Part Number A39835 C30380-A C30445-A

Part Number A46022-BM C39050-A

Part Number HA11244 2SC1685(R) 2SA673(C) 2$C1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2$C1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SD478 2SD478 28C2610BK 2802688 (K.L.M.) 2SC1890A (E.F) WosA WO6A WO6A 1SZ473H 1S8Z473H RD10F(C) HF-1 VOSE RD11E(B) WO6A 18881 1$Z473H RD20EV2 181887A 1S81887A 1$1887A 181887A RD6.8EV3

Part Number QMF53U1-1R25S QMF66U1-3R0S

6-15

Page 55

MEE 40tty ait IG! XIOS and XIO$ VIDEO AMP 2SC454C a, 28¢ 1685, L 1 xi02.x106 and Xi06 ViIOEO_AMP_2SA673C

  • (cu-s016 A | | leet Socker | pce Assy

ICO! POWER REGULATOR STR3B3 SU-I103A MAIN PCB ASSY

add. nd he om an ae ware | i co Tone Wav osc]

Schematic Notes Unless otherwise specified Resistance: (2) (K-KQ, M--MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1-> (yF) working voltage > 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), 7 i X70! X-RAY PROTECTOR X50) HORE. xO! WOT var wave NP - non-polar (or bipolar) electrolytic cap. 1 be 25CABAC or 2501685 B8cSer or BSeSSe seman —_ Refer to the parts list for additional component information.

  • i i con neerton : aci2ov cons/sone 2 indicates test point connection slow hn indicates chassis ground unless otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) a replace all components marked with safety symbol with identical type.
NOTE: FR - fusible resistor -—e—

G07-FBO Parts identification on circuit boards: 00-4147-03 e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 56

REPLACEMENT PARTS LIST—ELECTROHOME 13" MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have specia! characteristics

important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor

CR:Carbon Resistor

Comp. R Composition Resistor

OM R:Oxide Metal Film Resistor
VR:Variable Resistor

MFR Metal Film Resistor CMF R Coating Metal Film Resistor UNF R Nonflammable Resistor

FR:Fusible Resistor
NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and Capacitor

C Cap. M Cap. E Cap. BP E Cap.

MM Cap. PP Cap. MPP Cap. PS Cap. Tan. Cap.

model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Main PC.B. Assy CRT Socket PC.B. Ass'y

Ouiside of the P.C.B. Ass'y

Symbol Description Avot — Aicture Tube 13" Adyo1 ADeflection Yoke PC Magnet Wedge A\Flyback Transf. ArR1i1 AFocus VR AROS UNF Resistor 220.2,25W. K Aco4 = AC Capacitor 150pF, A C1.5KV xo1 Si. Transistor ICO1 IC Regulator Lot Degaussing Coii Degaussing Coil Pin Terminal (2) Degaussing Coil Pin Terminal Housing Groundstrap Ass'y Groundstrap Wire Terminal Groundstrap Spring (2) BR Support Bracket RH BR Support Bracket LH sc SCREW 10-% Pix Tube Mtg. (4) WA Pyramidal Lockwasher (4) Clip PC.B. Support (2) Ground Lug CH Chassis Base Part Number SU-1103A SU-3016A.

Part Number 370ESB22(E) €29123-V A76366-A 30006 A19183-A A46606-A QRF258K-221 QCZ0101-005 28D869 STR383 21-1007-31 34-708-01

34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Main P.C.B. Ass’y (SU-1103A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AR1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 AR1703 AR1704 AR1901 R1902 R1903 R1904 AFR1901 Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypronylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

Description

vR2002
vR2002
CMFR6.821WJ
OMR3.3KQ1WJ
OMR2.7KQ1WJ
OMR12KQ2W J
vR10KQ
AFR6822W K
ACMFR_11.82%W +1%
vR5KQ
OMR10KQ2WJ
OMR5.6KQ22W J
OMR68022W J
CMFR8.221WJ
CMFR4.721WJ
OMR5622WJ

OM R 39021WJ ZN OR ZN OR

ACMFR39KQ¥%W +1%
ACMFR7.68KQ%W +1%

A’Posistor

UNFR2Q7WK
CMFR5.623WJ
OMR10K22W J
AFR2202%W K

Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRGO19J-332 QRGO19J-272 QRGO29J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO29J-103 QRGO029J-562 QRGO29J-681 QRX019J-8R2 QRX019J-4R7 ORGO029J-560 ORGO19J-391 ERZ-CO5ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRGO26J-103Z QRH124K-221M Main P.C.B. Ass'y (SU-1103A) Parts List Capacitors Symbol C1402 C1414 C1412 C1508 C1511 AC1512 Description Tan. Cap. 2.2uF 16V K E Cap. 100uF 160V A E Cap. 3.3uF 160VA PP Cap. 5600pF 50V J E Cap. 47uF 160VA A\PP_ Cap. 2000pF DC1500V J AC1513 APP Cap. 2000pF DC1500V J ACc1514. APP Cap. 2500pF DC1500V J

C1515PPCap. 0.53uF DC1200V K

C1520 BPE Cap. 1uF 50VA

C1524M_Cap. 0.1uF 200V K
C1904ECap.
C1905ECap. 10uF 250V A

Aci1907_ AMM Cap. 0.1uF AC150VZ

Coils Symbol Description L1501 Peaking Coil L1502 Liniarty Coil L1503 Width Coil L1504 Heater Choke L1901 Line Filter

Transtormers Symbol Description T1501 Hor. Drive Transf. T1503 Side Pin Transf.

Semiconductors Symbol Description 1C1501 Lc. X1101 Si. Transistor X1102 Si. Transistor X1103 Si. Transistor X1104 Si. Transistor X1105 Si. Transistor X1106 Si. Transistor X1301 Si. Transistor X1302 Si. Transistor X1303 Si. Transistor X1304 Si. Transistor X1305 Si. Transistor X1401 Si. Transistor X1402 Si. Transistor X1501 Si. Transistor X1701 Si. Transistor D1101 Si. Diode D1102 Si. Diode 01103 Si. Diode D1301 Si. Diode D1401 Si. Diode D1402 Zener Diode D1503 Si. Diode D1504 Si. Diode D1505 Zener Diode D1506 Si. Diode D1507 Si. Diode D1508 Si. Diode AD1701 AZener Diode 4\D1901 ASi. Diode Ap1902_ = ASi. Diode A\D1903 ASi. Diode Ap1904_ — ASi. Diode

Miscellaneous ‘Symbol Description AF1901 AFuse 1A A\F1902 AXUL Fuse 3A Part Number QEES51CK-225B QEWS52CA-107 QEWS2CA-335, QFP31HJ-562 QEW52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS52EA-106 QFZ9008-104

Part Number A75360-6 A39934 C30380-A C30333-A A39475-J

Part Number A46022-BM C39050-A

Part Number HA11244 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 28A673(C) 2SC1685(R) 2SC1685(R) 28D478 2S8D478 2SC2610BK 2SC1685(P-S) WO6A WO6A WO6A 1$2473H 182473H RD10F(C) HF-1 VO9E RD11E(B) WO6A 18881 182473H D20EV2 181887A 1S1887A 181887A 181887A

Part Number QMF53U1-1ROS QMF66U1-3ROS Resistors Symbol Description R3105 VR 2002 R3106 VR 2002 R3113 VR 5KQ R3114 VR 5KQ R3115 VR 5KQ R3116 OM R 10K22W J R3117 OM R 10KQ22W J R3118 OM R 10K22W J R3119 Comp. R 3.3KQ%W K R3120 Comp. R 3.3KQ%W K R3121 Comp. R 3.3KQ%W K

Capacitors Symbol Description C3107 E Cap. 10uF 250VA C3108 C Cap. 1000pF DC1400V P

Coils Symbol Description L3101 Peaking coil

Semiconductors Symbol Description X3101 Si. Transistor X3102 Si. Transistor X3103, Si. Transistor

Miscellaneous Symbol Description A CRT Socket CRT Socket P.C.B. Ass'y (SU-3016A) Parts List

Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053, QVZ3234-053 QVZ3234-053 QRGO29J-103 QRGO029J-103 QRGO29J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS2EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 2802611 2802611 2S8C2611

Part Number A75522

Page 57

veer. tom THIST CABLE | [ asst |

[sven ng veRr._ Ht

douy Tye xt veut |

Benger “Seay 88

6-18

rcL_~
/[eensweaaee
|;a
gerstengsy2oy'
|seroa ee ieLeggs:Bae B5e5|
32284+|

| L_ise >] 4 gst

seaweEr |ty,|

j lie A a

13204 | SWEEP t, a : ones | pe +3} Lag Pea 2exy t J % H High r i “VOLTAGE

ORS ane Ve warn Flu 9% TOLE RAN TRESS STRBAEE MEST —_ 2 ALL sabECICLIORS bE Ww MiOPANEDS UNLESS Sree SCTE, Yq ae 82, 29 '

cxazea \

A-9740-05

REFERENCE ONLY

SCHEMATIC FOR

Y- 186-0 SWEEP BOARD RGB COLOR MONITO ZENITH | ‘* RADIO CorP..! B | CHICAGO. ILL.

Pi.» SEE PARTS UIST FOR APPLICABLE USAGE. fo sumben wine usto iste: ©. -# # @— PROVISION ON PRINTEE CIRCUIT SouRD.

Page 58

Ref. No.

C2131 C2152 63201 Cx3202 3203 CX3204 CX3205 3206 3207 ©3209 3211 3212 C3213 c3214 C3216 3217 3218 c3222 Cx3228 Cx3229 63233 C3244 C3261

CR3202 CR3203 CRX3204 CR3205 CR3206 CR3207

CR3208 CR3209 CR3210 CR3211 Qx3202 QX3204 Q3206 QX3207 Q3209 SWEEP BOARD (9-186-03)

Part No.DescriptionRef. No.Part No.Description

CAPACITORS TRANSFORMERS & COILS

22-780847 MF, 35V, +20% ElectrolyticL3207140-454Core, Ferrite Bead
22-7508-01022 MF, 38V, +20% Electrolytic13220F-13834Core & Sleeving Assy. (148-509-01)
22-7410-0510 MF, 100V, +20% ElectrolyticiX326120-3976Coil Width
22-7710-01C1 MF, 50V, +50%—10% ElectrolyticLXx326220-3975Coil, Linearity, with 205-271 Hot Meit
22-7711-08C47 MF, 63V, +50%-10% Electrolytic7320595-3344Transformer, Horizontal Driver
22-7773-2440.1 MF, 100V, +5% PolyesterTX320495-3581-01Transformer, Sweep

22-7523-01 0.01 MF, 2KV, +20% Disc 22-7708-04C 4.7 MF, 25V, +50%—10% Electrolytic RESISTORS

api)330 PF, 1000V, +10% DiscR210563-9921-948.2K Ohm, +5% 1/4W Film
22-72420.0018 MF, 200V, +10% DiscR211063-9921-64470K Ohm, +5% 1/4W Film
22-7777-20B0.047 MF, 200V, +10% PolyesterRot63-9919-833K Ohm, +2% 1/4W Film
po-rea4560 PF, 500V, 210% DiscR211263-9919-9610K Ohm, +2% 1/4W Film
22-7775-16A0.022 MF, 100V, +20% PolyesterAXg20463-9921-802.2K Ohm, +5% 1/4W Film
22-7775-10A0.0068 MF, 100V, +20% PolyesterAX320663-78053.3K Ohm, +5% 1/2W Carbon
22-5664470 BE, S00V.220% DiscRX320763-9921-3222 Ohm, +5% 1/4W Film
oo eeed470 PF, 500V, +20% DiscRX320863-10235-802.2K Ohm, +5% 1/4W Film
22-7774-15C0.018 MF, 100V, +10% PolyesterRX320963-10235-721K Ohm, +5% 1/4W Film
22-7742-10,(0.001 MF, SOV,£10% AxialRX321063-78053.3K Ohm, +5% 1/2W Carbon
22-6466530 PF. 3KV, +10% DiscRX321163-10810-073K Ohm, #1% 1/2W Film
22-7672-070.013 MF, 1.6K V, +5% PolypropyleneRX321463-10233-812.4K Ohm, +2% 1/4W Film
22-77280.68 MF, 200V, =10% PolyesterRX321663-10810-061.2K Ohm, +1% 1/2W Film
22-7566-240.1 MF, 250V, +10% PolyesterRX321763-7760270 Ohm. +5% 1/2W Carbon
22-7683-010.68 MF, 200V, +5% PolypropyleneRRX3215,63-10235-9812K Ohm, +5% 1/4W Film
X32 1863-10235-822.7K Ohm, +5% 1/4W Film
SEMICONDUCTORSAX321963-10235-884.7K Ohm, +5% 1/4W Film
103-142-01Diode, Low Voltage322463-9946-884.7K Ohm, +5% 1/2W Film
103-330ADiode, Low Voltage322563-10836-68680 Ohm, +5% 2W Wire Wound
103-308ADiode, Zener322663-10235-741.2K Ohm, +5% 1/4W Film
103-305Diode, Damper322763-10235-802.2K Ohm, +5% 1/4W Film
103-284ADiode, Low VoltageRX3235,63-10810-061.2K Ohm, +1% 1/2W Film
103-295-01ADiode, Low VoltageRX324053-10857-0410 Meg Ohm, +20% 1/2W Carbon
(used with 149-454)324263-10243-802.2K Ohm, +5% 1/2W Film
103-295-01ADiode, Low Voltage324363-10243-802.2K Ohm, +5% 1/2W Film
103-142-01Diode, Low Vaitage324463-7868100K Ohm, +5% 1/2W Carbon
103-142-01Diode, Low VoltageR326163-10444-86390 Ohm, +10% SW Wire Wound
103-142-01Diode, Low VoltageR326263-10565-65510 Ohm, +10% 1/2W Film
121-975Transistor, NPN326363-10565-65510 Ohm, +10% 1/2W Film
121-973Transistor, PNP, ShutdownR328263-10235-9610K Ohm, +5% 1/4W Film

121-1037 Transistor, NPN, Forward Driver 121-975, Transistor, NPN, Shutdown 121-1040 Transistor, NPN, Reverse Driver ZENITH MONITOR — SWEEP BOARD REPLACEMENT PARTS LIST

6-19

Page 59

340! Se sacs 2188"

rs i Rsaes ' me

Ce)

3467 i tae of im (99 Lega a ‘57K

ro alt

ost04

e329 29 93421 Teo 2K

VERT HIGH

92506 REQ ORE, lero $ es

6-20 2507 i r ry | ee L2s04 aH ga28 Sax

a _ typd zt DeGAUSSER ng28 ae i i” aa

  • Lit 4. -i_.J

SCHEMATIC FOR 9-227-01 RGB COLOR MONITOR

(MAIN BOARD)

ORP. c 9-227 M051-00087~-A024

Page 60

ZENITH MONITOR — MAIN BOARD REPLACEMENT PARTS LiST

Board Board 9-227 9-227

9-227-01Aet.No. PartNo.Description9-227-01

RESISTORS

xXRX2i01 63-10568-3222 Ohm, +5%, 1/2W Filmx
xX210263-10243-56220 Ohm, +5%,1/2W Filmx
xX210363-10235-88 4.7K Ohm, +5%, 1/2W Filmx
xXRX2104 63-10243-113 Ohm, +5%, 1/2W Filmx
xX — AX21053 Ofim, +5%, 1/2W Filmx
xXR21061K Ohm, +5%, 1/4W Filmx
xX2107560 Ohm, +5%, 1/4W Filmx
xXR210863-10235-66560 Ohm, +5%, 1/4W Filmx
xXR210963-105651 Ohm,+5%, 1/2W Filmx
xX211063-10565= 1 Ohm, +5%, 1/2W Filmxx
xXR211163-105651 Ohm, +5%, 1/2W Filmx
xX214263-105651 Ohm, +5%, 1/2W Filmx
XxXR211363-10243-60 330 Ohm, +5%, 1/2W Filmx
xXR211463-10235-721K Ohm, +5%, 1/4W Filmx
xXR211563-10235-88 4.7K Ohm, +5%, 1/4W Filmx
XxXR211663-10235-60 330 Ohm, +5%, 1/4W Film
xX211763-10235-802.2K Ohm, +5%, 1/4W Filmx
xXR211863-10235-88 4.7K Ohm, +5%, 1/4W Film
xX211963-10235-54180 Ohm, +5%, 1/4W Filmx
xX212063-10565-08 2.2 Ohm, +5%, 1/2W Film
xX212163-10243-52150 Ohm, +5%, 1/2W Filmx
xX2122§3-10243-52150 Ohm, +5%, 1/2W Film
xXR212563-9023-02550 Ohm, +20%, Control-x

Rotary Single-GRA x

X212663-10243-66560 Ohm, +5%, 1/2W Filmx
xR212663-10243-53160 Ohm, +5%, 1/2W Filmx
XR212763-10243-69 750 Ohm, +5%, 1W Carbonx
xR2128—63-10243-66560 Ohm, +5%, 1/2W Filmx
XR212863-6058510 Ohm, +5%, 1W Carbonx
XR212963-10243-65510 Ohm, +5%, 1/2W Carbonx
xR250163-10236-28220K Ohm, +5%, 1/4W Film
XR250163-10236-522.2 Meg Ohm, +5%, 1/4W Filmx
xX250263-10235-905.6K Ohm, +5%, 1/4W Filmx
xR250363-10235-56220 Ohm, +5%, 1/4W Filmx
X250363-10235-58270 Ohm, +5%, 1/4W Filmx
xR250463-10235-802.2K Ohm, +5%, 1/4W Filmx
X250463-10235-69750 Ohm,+5%, 1/4W Filmx
xR250563-10857-11_5K Ohm, Control-Rotaryx

Singie-RED x

X250563-10857-27800 Ohm, Control-Rotaryx

Single-Red Cut-Off x

xR250663-10857-301K Ohm, Control-Rotaryx

Single-Yellow x

X250663-10857-27800 Ohm, Control-Rotaryx

Single-Red Drive x

xR250763-10285-761.5K Ohm, +5%, 1/4W Filmx
XR250763-10235-755%, 1/4W Filmx
XR250863-10235-93,£5%, 1/4W Filmx
xR250863-10235-82, +5%, 1/4W Filmx
xR250963-10235-80, +5%, 1/4W Filmx
xR251063-10235-50120 Ohm, +5%, 1/4W Filmx
X251063-10235-48100 Ohm, +5%, 1/4W Filmxx
xR251163-10235-741.2K Ohm, +5%, 1/4W Filmxx
XR251163-10235-67 620 Ohm, +5%, 1/4W Filmxx
xR251263-10236-28220K Ohm, +5%, 1/4W Filmxx
XR251263-10236-522.2 Meg Ohm, +5%, 1/4W Filmx
xXR251363-10235-90 5.6K Ohm, +5%, 1/4W Film
xR251463-10235-56 220 Ohm, +5%, 1/4W Filmx
X251463-10235-58 270 Ohm, +5%, 1/4W Film
xR2515§3-10235-80 2.2K Ohm, +5%, 1/4W Filmxx
251563-10235-71910 Ohm, +5%, 1/4W Filmxx
xR251663-10857-325K Ohm, Control-Rotaryx

Single-Green x

X251663-10857-25800 Ohm, Control-Rotaryxx

Single-Green Cut-Off x

x251763-10857-301K Ohm, Control-Rotaryx
Single-Yellowxx
X251763-10857-25 800 Ohm, Control-Rotaryxx
Single-Green Drivexx
xR251863-10235-761.5K Ohm, +5%, 1/4W Filmx

MAIN BOARD (Continued)

Board 9-227

Ref.No. PartNo.Description9-227-01Ret.No. PartNoDescription

RESISTORS (Continued) RESISTORS (Continued)

R251863-10235-731.1K Ohm, +5%, 1/4W FilmxX322263-10235-40 47 Ohm, 15%, 1/4W Film
R251963-10235-937.5K Ohm, +5%, 1/4W FilmxX323163-99821 Ohm,+10%, 2W Wirewound
R251963-10235-822.7K Ohm, +5%, 1/4W FilmxX323363-10565-143.9 Ohm, +5%, 1/2W Film
R252062-10235-802.2K Ohm, +5%, 1/4W FilmxXR323463-10565-143.9 Ohm, +5%, 1/2W Film
R252163-10235-50120 Ohm,+5%. 1/4W FilmxX323963-10244-20100K Ohm, +5%, 1/2W Film
252163-10235-48100 Ohm,+5%. 1/4W FilmxX-R324%63-82464 Ohm, 10W Wirewound
R252263-10235-741.2K Ohm, +5%., 1/4W FilmxXR324463-10840-4047 Ohm, +5%, 3W Film,
R252363-10236-28 220K Ohm,+5%, 1/4W FilmTin Oxide
R252363-10236-82 2.2 Meg Ohm,+5%, 1/4W FilmxXR324563-10710A_—Thermistor
R252463-10235-90 5.6K Ohm, +5%. 1/4W FilmxXRX3246 63-10857-031.2 Meg Ohm, +20%
R252563-19235-56 220 Ohm, +5%, 1/4W Film1/2W Carbon
R252536.%, 1/4W FilmXR326063-10243-9610K Ohm, +5%, 1/2W Film
R25262.2K Ohm, +5%, 1/4W FilmXR326163-10244-24150K Ohm,+5%, 1/4W Film
R2526750 Ohm, +5%, 1/4W FilmXR326263-10235-68680 Ohm, +5%, 1/4W Film
R252763-10857-315K Ohm, Control-RotaryxXR340163-10236-461.2 Meg Ohm, +5%, 1/4W Film
Single-BiueXxX340263-10236-22120K Ohm, +5%, 1/4W Film
R252763-10857-26 800 Ohm, Control-RotaryxXR340363-10235-863.9K Ohm, +5%, 1/4W Film
Single-Blue Cut-OttxX3404 — 63-10235-863.9K Ohm, +5%, 1/4W Film
R252863-10857-301K Ohm, Control-RotaryXxXR340563-10236-0833K Ohm, +5%, 1/4W Film
Single-YellowxX340663-10235-68680 Ohm, +5%, 1/4W Film
R252863-10857-26 800 Ohm,Controi-RotaryxX340763-10236-1882K Ohm, +5%, 1/4W Film
Sing!s-Blue DrivexXR340863-10236-0422K Ohm, +5%, 1/4W Film
R252963-10235-761.5K Ohm, +5%, 1/4W FilmxX340963-10857-17100K Ohm, Control-Rotary
252963-10235-751.3K Ohm, +5%, 1/4W FilmSingle-Green
R253063-10235-93 7.5K Ohm, +5%, 1/4W FilmxXR341063-10236-31300K Ohm, +5%, 1/4W Film
R253063-10235-822.7K Ohm, +5%, 1/4W FilmxXR341163-10236-0320K Ohm, +5%, 1/4W Film
R253163-10235-80 2.2K Ohm, +5%, 1/4W FilmxXR3412_63-10236-1351K Ohm, +5%, 1/4W Film
R253263-10235-50120 Ohm, +5%, 1/4W FilmxXR3413_63-10236-0730K Ohm, +5%, 1/4W Film
R253263-10235-48100 Ohm,+5%, 1/4W FilmxX341463-10235-9812K Ohm, +5%, 1/4W Film
R253363-10235-741.2K Ohm, +5%, 1/4W FilmxX341563-10236-0218K Ohm, +5%, 1/4W Film
R253463-10235-52150 Ohm, +5%, 1/4W FilmxXR3417_63-10243-60 330 Ohm, +5%, 1/2W Film
R253563-10235-52150 Ohm, +5%, 1/4W FilmXxX341863-10857-082K Ohm, Control-Rotary
R253663-10235-52150 Ohm, +5%, 1/4W FilmSingle-Yellow
253763-10235-52150 Ohm,+5%, 1/4W FilmxX341963-10235-84 3.3K Ohm, +5%, 1/4W Film
R253863-10235-56 220 Ohm, +5%, 1/4W FilmxX342063-10236-10 39K Ohm, +5%, 1/4W Film
R253863-10235-48100 Ohm, +5%, 1/4W FilmxX342163-10235-731.1K Ohm, +5%, 1/4W Film
R253963-10235-56220 Ohm, +5%, 1/4W FilmxX342263-10243-60 330 Ohm, +5%, 1/2W Film
253963-10235-48100 Ohm, +5%, 1/4W FilmxXR342363-10243-60 330 Ohm, +5%, 1/2W Film
R254063-10235-56 220 Ohm,+5%, 1/4W FilmxX342463-10235-721K Ohm, +5%, 1/4W Film
254063-10235-48100 Ohm, +5%, 1/4W FilmxX342563-10235-88 4.7K Ohm, +5%, 1/4W Film
R254163-10235-545%, 1/4W FilmxX342863-10235-82 2.7K Ohm, +5%, 1/4W Film
254263-10235-53_160 Ohm, +5%, 1/4W FilmxXR342963-10235-761.5K Ohm, +5%, 1/4W Film
R254363-10235-54180 Ohm, +5%, 1/4W FilmxXR343163-10235-80 2.2K Ohm, +5%, 1/4W Film
254463-10235-54180 Ohm, +5%, 1/4W FilmxR3432_63-10235-55 200 Ohm, +5%, 1/4W Film
R254563-10235-54180 Ohm, +5%, 1/4W FilmXR343263-10235-79 2K Ohm, =5%, 1/4W Film
254663-10235-53160 Ohm, +5%,1/4W FilmxXR3433°63-10236-20100K Ohm, +5%, 1/4W Film
R254863-10235-67 620 Ohm, +5%, 1/4W FilmxX343463-10236-22120K Ohm,+5%, 1/4W Film
R254963-10235-67 620 Ohm, +5%, 1/4W FilmxX343563-10235-63 430 Ohm, +5%, 1/4W Film
R255063-10235-32 22 Ohm, +5%, 1/4W FilmxX343663-10235-721K Ohm, +5%, 1/4W Film
R255263-10235-3222 Ohm, +5%, 1/4W FilmxX343963-10243-79 2K Ohm, +5%, 1/2W Film
R255463-10235-3222 Ohm, +5%, 1/4W FilmxXR344063-10235-86 3.9K Ohm, +5%, 1/4W Film
R320163-10235-59 300 Ohm, +5%, 1/4W FilmxR344i63-10857100 Ohm, Control-Rotary
R320263-10235-44 68 Ohm, +5%, 1/4W FilmSingle-Horizontal Center
R320363-10235-52150 Ohm, +5%, 1/4W FilmXR3441_63-10857-02250 Ohm, Control-Rotary
R320583-7781820 Ohm,+5%, 1/2W CarbonSingle-Horizontal Center
R3206F-1185112 Ohm, +10%, 10W ResistorxXR3442_63-10235-863.9K Ohm, +5%, 1/4W Film
& Splice Assy.xR3443_63-10235-65510 Ohm, +5%, 1/4W Film
R320663-10460-5012 Ohm, + 10%, 10WXR3443_63-10235-802.2K Ohm, +5%, 1/4W Film
WirewoundxX344463-10235-60330 Ohm, +5%, 1/4W Film
321063-10420-312 Ohm, +5%, 2W WirewoundxX344563-10235-802.2K Ohm, +5%, 1/4W Film
321263-10235-761.5K Ohm, +5%, 1/4W FilmX344663-10235-721K Ohm, +5%, 1/4W Film
R321363-10235-833K Ohm, +5%, 1/4W Filmx344963-10235-761.5K Ohm, +5%, 1/4W Film
R321363-10235-86 3.9K Ohm, +5%, 1/4W FilmxR345163-10235-82 2.7K Ohm, +5%, 1/4W Film
R321463-10235-741.2K Ohm, +5%, 1/4W FilmX345163-10235-88 4.7K Ohm, +5%, 1/4W Film
R321563-10244-38560K Ohm,+5%, 1/2W FilmxXR345263-10235-92 6.8K Ohm, +5%, 1/4W Film
321563-10244-40XR3453_63-10235-754.3K Ohm, +5%, 1/4W Film
R321663-10244-25xXR346163-10236 = 15K Ohm, +5%, 1/4W Film
R321763-10244-33,xXR346263-10236-13_ 51K Ohm, #5%, 1/4W Film
R321863-10235-802.2K Ohm, +5%, 1/4W Film

3219 63-10244-38 560K Ohm, +5%, 1/2W Film

Ref. No.Part No.Description

CAPACITORS

C210122-7775-10A0.0068 MF, 100V +20% Polyester
210222-7775-24A0.1 MF, 100V +20% Polyester
210322-7709-09C100 MF, 35V +50%—10% Electrolytic
C210422-7613-24D0.01 MF, SOV +10% Disc
C210522-7390-020.47 MF, 50V +20% Electrolytic
210622-7710-07C33 MF, 50V +50%~10% Electrolytic
C210722-7615-03D0.0033 MF, 50V +80%~10% Disc
C211022-7742-100.001 MF, 50V +10% Polyester
c2itt22-7774-17A0.027 MF, 100V +10% Polyester
C217622-7725680 MF, 50V +100%-10% Electrolytic
C250122-7621-42C220 PF, SOV +5% Disc
250222-7621-42C220 PF, SOV +5% Disc
C250322-7621-42C220 PF, 50V +5% Disc
320122-7775-24A0.1 MF, 100V +20% Polyester
320422-76034.7 MF, 315V +100%-10% Electrolytic
C320522-35120.01 MF, 1KV +40%-20% Disc
C320622-7603-01A10 MF, 315V +100%-10% Electrolytic
320722-7742-100.001 MF, SOV +10% Axial
320822-7742-100.001 MF, 50V +10% Axial
320922-7395470 PF, 500V +5% Disc
323422-7395470 PF, 500V +5% Disc
C323622-7861-142200 MF, 35V +20% Electrolytic
C324622-7603-01A10 MF, 315V +100%~10% Electrolytic
C324722-7860-12470 MF, 25V +20% Electrolytic
324922-7431-060.0047 MF, +20% Disc
CX325022-7431-060.0047 MF, +20% Disc
325122-78110.001 MF, 1KV +10% Disc
©325222-78110.001 MF, 1KV +10% Disc
C325322-78110.001 MF, 1KV +10% Disc
C325422-7404-0622 MF, 16V +20% Electrolytic
C325622-7508-05B2200 MF, 35V +50%~10% Electrolytic
325722-7395470 PF, 500V +5% Disc
340122-7613-24D0.01 MF, 50V +10% Disc
340222-7406-011.0 MF, 35V +20% Electrolytic,
6340322-7773-18A0.033 MF, 100V +5% Polyester
C340422-7773-17A0.027 MF, 100V +5% Polyester
340522-7775-10A0.0068 MF, 100V +20% Polyester
c340722-7710-01A1.0 MF, SOV +50%—10% Electrolytic
C340922-7709-08C100 MF, 35V +100%-10% Electrolytic
C341022-7404-06A22 MF, 16V +20% Electrolytic NP
341122-7708-09100 MF, 25V +50%~10% Electrolytic
C341222-7710-01C1.0 MF, SOV +50%~10% Electrolytic
0341322-7562-320.47 MF, 100V +8% Polyester
341422-T774-16A0.022 MF, 100V +10% Polyester
C341922-7751-39180 PF, 50V +5% Axiai
C3420,22-7710-01C1.0 MF, 50V +50%~10% Electrolytic
342122-7773-18B0.033 MF, 100V +5% Polyester
342222-7613-24D0.01 MF, 50V +10% Dise
©342322-7613-08D470 PF, 50V +10% Disc
C342422-7742-05390 PF, 50V +10% Axial
C342522-7742-100.001 MF, SOV +10% Axial
C342622-7742-100.01 MF, SOV +10% Axial
C342722-7647-35C150 PF, +10% Axial
6342822-7774-120.01 MF, 100V +10% Polyester
C342822-7774-20A0.047 MF, 100V +10% Polyester

(on-0t version)

342922-7405-044.7 MF, 25V +20% Electrolytic NP
342922-74060.47 MF, 35V +20% Electrolytic NP

(on-01 version)

343022-7613-24D0.01 MF, 50V +10% Disc
C343122-7774-16A0.022 MF, 100V +10% Polyester
C343422-7742-06470 PF, 50V +10% Axial
C343622-7613-24C0.01 MF, 100V +10% Disc
C345022-7739-29A0.27 MF, 100V +10% Polyester
C345022-7619-41C200 PF, 50V +5% Disc

(on-01 version)

346122-7710-01C1.0 MF, SOV +50%~10% Electrolytic
C346222-7710-01C1.0 MF, 50V +50%~10% Electrolytic
C346222-7739-090.0056 MF, 100V +10% Polyester

(on-01 version)

C346322-750847 MF, 35V +20% Electrolytic

6-21

Page 61

ZENITH MONITOR — CRT SOCKET BOARD MAIN BOARD (Continued) REPLACEMENT PARTS LIST

Ref. No.Part No.Description

SEMICONDUCTORS CRT SOCKET (9-155-10)

cR2104103-142-01Diode, Low Voltage
CR2105103-254-01Diode, Low VoltageRef. No.Part No.Description
CR2106103-254-01Diode, Low Voltage
CR2107103-254-01Diode, Low VoltageCAPACITORS
cR2501103-142-01Diode, Low Voltagecs10122-46710.01 MF, 1.5KV, +80%-20% Disc
cR2502103-142-01Diode, Low VoltageC510222-38120.01 MF, 1KV, +40%-10% Disc
CR2503103-142-01Diode, Low Voltage
CR3202103-330ADiode, Low VoltageTRANSFORMERS & COILS
CR3205103-309-01Diode, Zener 10V 1WL510220-3887-28E220MH Peaking
CR3206103-254-01Diode, Low Voltage510320-3887-28E220MH Peaking
CR3208103-326ADiode, Low Voltage510420-3887-28E220MH Peaking
CR3210103-254-01Diode, Low Voltage
CR3211103-254-01Diode, Low Voltage
CR3214103-284-ADiode, Low VoltageSEMICONDUCTORS
CR3217103-326Diode, Low VoltageQs5101F7510Transistor, NPN, Video Out, Blue
CR3219403-330Diode, Low Voltage5102F7510Transistor, NPN, Video Out, Red
CR3223403-330ADiode, Low VoltageQ5103F7510Transistor, NPN, Video Out, Green
CR3224103-330ADiode, Low Voltage
CR3231103-315-06ADiodeRESISTORS
CR3232103-315-06ADiodeR510163-10840-884.7K Ohm, +5%, 3W Film
CR3233,103-315-06ADiode510263-77851K Ohm, +10%, 1/2W Carbon
CR3234103-315-06ADiode510363-77851K Ohm, +10%, 1/2W Carbon
CR3235103-2840Diode, Low VoltageR510463-10235-54180 Ohm, +5%, 1/4W Film
CR3401103-142-01Diode, Low VoltageR510563-10235-48100 Ohm, +5%, 1/4W Film
R3404103-143-01Diode, Low Voltage510663-77851K Ohm, +10%, 1/2W Carbon
CR3405103-142-01Diode, Low VoltageR510763-77851K Ohm, +10%, 1/2W Carbon
CR3408103-142-01Diode, Low Voltage510863-77851K Ohm, +10%, 1/2W Carbon
CR3408103-279-14Diode, Zener 6.8V 1/2WR510963-77851K Ohm, #10%, 1/2W Carbon
Q2101F-10896Transistor & Heat Sink Assy.R511063-7785,1K Ohm, 10%, 1/2W Carbon
2102F-10896Transistor & Heat Sink Assy.R511163-77992.2K Ohm, +10%, 1/2W Carbon
Q2103421-975Transistor NPN511263-10840-884.7K Ohm, +5%, 3W Carbon
Q2104121-1064Transistor PNP511363-10840-884.7K Ohm, +5%, 3W Carbon
Q2501121-1019Transistor PNPR511463-10235-54180 Ohm, +5%, 1/4W Film
2502121-895Transistor NPN511563-10235-54180 Ohm, +5%, 1/4W Film
2502121-551Transistor NPN

(on-01 version) MISCELLANEOUS

o2609Teh 1eteTranslator PRE5A286-799Stake Connector 4/.156
92604121-895Transistor NPN5C286-799Stake Connector4/.156
2504121-551Transistor NPN5H386-799Stake Connector 2/.156
(on-01 version)|5X786-799Stake Connector 1/.312
2505121-1019Transistor PNP‘A-10008CRT Socket
2506121-895Transistor NPN
Q2506121-551Transistor NPN

(on-01 version)

Q2507121-1019Transistor
2508121-1019Transistor
Q2509121-1019Transistor
Q3200F-12737Transistor & Heat Sink Assy.
3201121-499-01Transistor NPN Regular Feed Back
Q3202121-1034Transistor NPN
Q3203121-1059Transistor PNP
93401123-895Transistor NPN
3402121-986Transistor PNP
Q3403121-985Transistor NPN
3404121-895Transistor NPN
3405121-895Transistor NPN

TRANSFORMERS & COILS

L.250220-3887-01Coil Peaking 1.2 UH
1250320-3887-01Coil Peaking 1.2UH
1250420-3887-01Coil Peaking 1.2 UH
1320120-2021Coil Peaking 100 UH
Lx320295-3501-01Transformer Choke 60 UH
1340120-3831Coil Peaking 663 UH
L240220-3998Coil Peaking 39 UH
1340220-4026Coil Turnable 39 UH

(on-01 version)

6-22

Page 62

FIL

FIL

9-155-10 | (204-980) |

\

RS110

|1KI
I101E5103|

4.7K 3H

Ls102 2200H

! I +

S113 15104 315103 i 220UH 3220UH

' | RS113 $RS112

H4Q5103.4.7K7K!

Lsio1 121-1034} 3H

+ +

Q5102

'+121-1034 |

H RED OUT | " c5102

Teet c B 01 al RS115

iace180\
iTe74Hi
  • RS114 R5105 180
1/4Hwe1/44
IAB|
HrmI
'|iSR2|

+156 CENTERS

SA2

I Lea L Ne GROUND RED \ ot — GREEN

Lgase — BLUE

© 140 voc “— GROUND

DAS ‘ROUND

NOTE: ALL RESISTORS ARE 1/2WATT UNLESS OTHERWISE ‘SPECIFIED.

NOTES: (USED WITH CIRCUIT REFERENCE DESIGNATORS) P/L = SEE PARTS LIST FOR APPLICABLE USAGE. oo = JUMPER USED INSTEAD. + —® = @ = PROVISION ON PRINTED CIRCUIT BOARD.

th SIONAL (GROUND M05 1-00087-A022

SCHEMATIC FOR 2-15S-1u0 AUR MONITOR cuLkET 4

6-23

Page 63

p-—TO H.0.7. ASSY

A-I0530

Re La 30 2 | 20H iE:

SWEEP MODULE M05 1-00087-A023

sc FOR

HEMAT IC

A-10539 WIDTH STEF ASSY.

ZENITH

RADIO CORP. ISSUE

CHICAGO. ILL.

Page 64
poeaeeoe ao_—|F-13473
ee_fa}7
3v3i|
|foo|sooe |, |
|MAIN MODULEom||TeoWy ees |
|{SEE CHART}\|
| fel(2hes~

| ofaly |

| |e7peltas-o1oe
°ts]
| olo3\
L_Ls}ro
|aB.C. GROUNG
alc|OAG |ry
a|Ww‘
|SWEEP MODULE|

(SEE CHART) |

xi||
poo|i3S33R3

[ae eco | 18 .? i H | rT] |

=zee7ae38ae[iaa]Heme RASC ge earth ant cea
j{eace] [ooess] [ooo |[soooo o|fo o oae++ 4CORATICH Se FUMRONERTS SHOULD, BE RE
L.7~;I‘see ee ean eeat oa ahh ao
|HV POWERTHE UI Ye uu4
L.=|Tene ake S— AUST” SONFORM” TC_ORTSINAL
Ls}|||1°pSUPPLYPEEoNCMe ET TUN OF REPAIRS.

| SPECIAL ZIRGJITS ARE ALSC USEL 0 FRE

rh|| YoKe(SEE CHART)| GENT SHCZR ANE FIRE HADARO, THECC AREAS
|aispa1 TeErteTenricws we cevreR 2<°" INL HOE
AIR|1| Te THE, LTE NUMBERSrerTAL

i

ley||| BHICH ARE REGIIREL TU MRINTAIN CAFE PER-
|To DEGAUSSERaa| A SEE A Pehl RE
i205Shel €unMEN oes ome

AC \ | SAFETY A.C FERFURMANCE IMPROVEMENT

HionlCHANGES [NTC THE SET 12 NCT Ut. AEC
\[Fee eee sree Htatice
1~a.7I |[aaPRINieC
|363[>]

a | | |

srz/oe os]:+ ASSeHBLY
l| =a|WIDTH STEP
ig_|/|(SEE CHART) |
——a2}--— a a\ |i
3la. /hi

| } ||

562 |)|

VIDEO OUT (SEE CHART) |

[e |sxa.fn|

M05 1-00087-A025

RCUNNECT

GAME

FOR MONT TOR

a@ar

Page 65

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.