CATHODE RAY TOMES

Meadows Lazer Command

Lazer Command (Meadows Games, Inc., 1976) · Document · 17 pages · 7 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

LAZER COMMAND

Model LC-1

Page 3

TABLE OF CONTENTS

1- INTRODUCTION

2- WARRANTY INFORMATION

3- SETUP AND CHECKOUT

4- GAME SEQUENCE

5- CABINET ENTRY

6- COIN ACCEPTOR T- ADJUSTMENTS /MAINTENANCE

4-WAY CONTROL HANDLES

DRIVERS EJECT BUTTONS

NOVICE/EXPERT SWITCHES

COINS PER GAME

GAME TIMER

DISPLAY MONITOR

PCB REMOVAL

8- TROUBLE SHOOTING HINTS

ILLUSTRATIONS

FIGURE #1 COIN MECHANISM

FIGURE #2 LOGIC PCB

FIGURE #3 4-WAY CONTROL HANDLE

FIGURE #4 WIRE HARNESS

FIGURE #5 MONITOR MANUAL

Page 4

INTRODUCTION

LAZER COMMAND, a game of skill and strategy, is a game that depicts

a futuristic battle between two groups of nuclear powered lazer tanks.

The object of the game is to blow up all 15 enemy tanks while trying

to evade being hit by opponent's shooting lazers. The two opposing

tanks are separated by either a simple "NOVICE" maze or a complex

"EXPERT maze. Only one of each player's tank can move or shoot its

lazer at a time, and this tank must be occupied by its respective

driver. "For strategic purposes" the driver can be moved at any-

time from tank to tank. (See Section "DRIVERS EJECT BUTTON," page 3.)

WARRANTY

PRINTED CIRCUIT BOARDS: Contact the distributor from whom the game

was purchased for warranty repair and/or replacement information.

NOTE: Any PCB repair attempted by anyone other than factory

authorized service people, or any damage due to improper

handling or use shall void any existing warranty. Proper

procedures for removal and replacement, as outlined in

manual, must be adhered to.

DISPLAY MONITOR: Contact the distributor from whom the game was

purchased for warranty repair and/or replacement information.

NOTE: Any monitor repair attempted by anyone other than factory

authorized people, or any damage due to improper handling

or Use, shall void any existing warranty.

ALL EQUIPMENT RETURNED TO THE FACTORY MUST HAVE RETURN AUTHORIZATION NUMBER AND TRAVEL FREIGHT PREPAID. PLEASE LIST SYMPTOMS OR PROBLEMS TO EXPEDITE REPAIRS.

Page 5

LAZER_COMMAND SETUP AND CHECKOUT

When the game is received and unpacked, save all packing materials

in the event that it was damaged and must be returned. After reading

"CABINET ENTRY'' section, proceed to inspect the interior of the cabinet

for loose or damaged connectors, wires, hardware, etc. If everything

seems in satisfactory condition, plug the game in and play it as de-

scribed in the section "GAME SEQUENCE.'' For questions about length

of play time, coins per game, sound level, or anything relating to

picture image, see the section 'ADJUSTMENTS/MAINTENANCE,'!

GAME SEQUENCE

CONTROL AND SWITCH FUNCTIONS

COIN: Operator selectable:

1 coin, 25¢, per play

2 coins, 50¢, per play

START NOVICE/START EXPERT: Generates a simple or a complex maze on

the display monitor and starts the game.

4-WAY CONTROL HANDLE: Allows manuevering in any one of 4 directions

at atime. UP, DOWN, LEFT, RIGHT. .

Page 6

DRIVERS EJECT BUTTON: Momentarily pressing EJECT BUTTON while actu-

ating the control handle ejects the driver out of his tank. NOTE: !t

is not necessary to keep the EJECT BUTTON constantly depressed - only

long enough to get driver out of tank he jis presently in. To enter

another tank, after ejecting of after being blown up, a driver simply

moves into another of his own tanks by moving the control handle. The

driver from one side will not operate tanks of the opposing player.

DISPLAY MONITOR: The upper left hand corner shows the time remaining

during or at the end of game, and the upper middle section indicates

coin credits. The lower left and right corners depict the number of

enemy tanks ''blown up'' by the respective left and right player. The

central area of the display shows the maze battlefield. The game ends

when either all tanks of one player are blown up or if the time clock

has run out. When the game has ended the word WINNER will be displayed

on the side having blown up the largest number of enemy tanks. In the

case of a tie, the word DRAW will appear in the center of the screen.

CABINET ENTRY

Entry into the LAZER cabinet is at three points: the coin door, the

back door, and the control panel.

COIN DOOR

The coin door is hinged to open from right to left giving access to

the following:

Coin Box Coin Mechanism Control Panel Wing Nuts

Page 7

BACK DOOR

The back door tilts out from the top and lifts up for removal. This

allows access to the following:

Display Monitor Harness Logic PCB

CONTROL PANEL

To open the control panel open the coin door first. Remove the two

wing nuts located up towards the control panel to the left and right.

Finally, swing the control panel away from the cabinet. This will

give access to the following:

Cleaning Monitor/Inner Plexiglass 4-Way Control Handles Plexiglass Removal (for instruction cards) Left Eject Switch Right Eject Switch Speaker Start Expert Switch Start Novice Switch

COIN ACCEPTOR OPERATION, ADJUSTMENT AND MAINTENANCE

SEE FIGURE |

The detection and rejection of undesired or counterfeit coins are

determined by size (both thickness and diameter), weight and metallic

composition.

The transfer cradle (#9) is used to test both the size and weight of

the coin. The coin must first pivot an "undersize' lever (10) to

Page 8

unlock the transfer cradle and can be returned by actuating the wiper

operating lever (17). Oversize diameter coins will fail to pass

between the transfer cradle and the wiper and can be returned by

operating the wiper lever. Coins that are oversize in thickness will

fail to pass between the magnet gate (11) and the main channel (5)

and will have to be dislodged by actuating the wiper operating lever.

Underweight coins will fail to overcome the transfer cradle counter-

weight and can be returned by operating the wiper lever.

A magnet is used to test the metallic composition of the coin. Highly

magnetic coins, such as steel or iron, will be retained by the magnet

and can be returned by actuating the wiper operating lever. Coins

having comparatively high magnetic properties will be slowed down by

the magnet and will drop off the rail short of the accept entrance and

will be returned. Coins having little or no magnetic properties, such

as brass or zinc, will pass through the magnetic field so fast they

will overshoot the accept entrance and will be returned.

ADJUSTMENT

All coin acceptors leave the factory adjusted for maximum performance.

If, however, more critical adjustment is desired, or if the unit has

been disassembled for cleaning, the following adjustment procedure is

suggested.

Page 9

KICKER AND SEPARATOR

Set the acceptor on a level surface with the back of the unit

facing you (the kicker and separator are on the back).

Loosen the screws holding the kicker (1) and the separator (3)

and move both the kicker (2) and the separator (4) as far to

the right as they will go. Tighten the screws lightly.

Insert several test coins (both old and new) and note that

some are returned by striking the separator.

Loosen the separator screw and move the separator a slight

amount to the left, Retighten the screw.

Insert the test coins again, and if some are still returned,

repeat Step d until all coins are accepted.

Loosen the kicker screw and move the kicker a slight amount to

the right.

Insert the test coins again and, if some of them are returned,

repeat Step f until all coins are accepted.

Be sure that both screws are tight after the adjustments have

been made.

THE MAGNETIC GATE

Set the acceptor with the front of the unit facing you in the

test position.

Turn the magnet gate adjustor (12) out (counter-clockwise)

until none of the coins will fit through.

Page 10

c. With a coin resting in the transfer cradle, turn the adjustor in (clockwise) until the coin barely passes through the magnet gate.

d. Test this adjustment using several coins, and if any fail to pass

through the magnet gate, repeat Step c until all coins are accepted.

e. Fix the gate adjustor in this position with a drop of glue or

Loctite, if necessary.

ACCEPTOR MAINTENANCE

Depending on the environment in which the acceptor is used, periodic

preventative maintenance should be performed.

The mainplate (5) may be cleaned with any liquid household cleaner.

Thorough rinsing and drying are necessary to remove deposits and/or

film. Remove all metal particles from the magnet by guiding a screw-

driver along the edges of the magnet. Remove the transfer cradle and

undersize lever and clean the bushings and pivot pins and re-assemble.

Spray the entire unit lightly with WD-40, a silicone lubricant.

4-WAY CONTROL HANDLES, ADJUSTMENT AND MAINTENANCE

These controls are factory set and need no adjustment. However, if

switch replacement is necessary, simply remove connector and two screws

holding switch to plate. For fire button removal, unscrew with appro-

priate tool or with a pair of regular pliers. Then remove slide on

terminals.

Page 11

DRIVERS EJECT BUTTON SWITCHES, ADJUSTMENT AND MAINTENANCE

If access to these switches is required see the section, ''CABINET ENTRY."

To remove either of these switches, disconnect the slide on terminals

and undo the 9/16'' nut holding the switch to the contro] panel.

NOVICE/EXPERT SWITCHES

In the event these switches need to be removed for replacement, gain

access to them by following directions under the section, "CABINET ENTRY."

Continue by removing the 9/16" nut holding the switch to the control

panel.

COINS PER GAME, ADJUSTMENT

The number of plays per coin is switch adjustable to either | coin per

game or 2 coins per game. See the illustration of the Logic PCB for

switch details.

GAME TIME, ADJUSTMENT

Length can be set to either 1, 1.5, 2, or 3 minutes. See illustration

of Logic PCB for switch details.

Page 12

DISPLAY MONITOR, ADJUSTMENT AND MAINTENANCE

The display monitor contains the following adjustments from left to

right:

Contrast: Adjustment for clear picture

Brightness: Adjustment to suit location

Vertical Hold: Adjustment if picture flips

Horizontal Hold: Adjustment if picture has diagonal lines

or is distorted

Volume: Adjustment to suit location noise level

For any maintenance see your "DISPLAY MONITOR MANUAL."

For access to display monitor see ''Back Door'' section under ''CABINET

ENTRY.''

PCB REMOVAL

Before removing PCB's, power cord should be disconnected. Note the

position of PCB to the connector to ensure proper connection upon

replacement.

Page 13

TROUBLE SHOOTING HINTS

TESTING COMPONENTS OF GAME

BUTTONS & COIN SWITCH are normally closed. When pushed they are open.

The buttons can be by-passed by pulling off one of the terminals.

HARNESS can be tested by an ohm-meter or continuity checker.

FUSES are checked by visual inspection or continuity checker.

LOGIC PCB & TV MONITOR can be checked by substitution of a good replace-

ment. Repair of logic PCB & monitor should only be serviced by experi-

enced technicians.

NO PICTURE: Check if back of picture tube is lit, if not, inspect fuses,

power cord, and power outlet. If these are good and tube is not lit,

repair of monitor is necessary.

1f the tube is lit, check adjustments of brightness and contrast. Test

continuity of logic board pins #1 and #3 (5 volt dc power supply), and

pin #5 (video output). If all check out, the problem is either the

logic PCB or the monitor.

NO SOUND: Check the adjustment of the volume control on the TY monitor.

Test the continuity of the logic PCB J2-Pin 11 (audio signal), and the

monitor pins #5 and #8 (speaker wires). Check the speaker, logic PCB,

and TV monitor.

Page 14

. < 5 ~

REVISIONS

KICKER SCREW DESCRIPTION DATE APPROVED:

KICKER SEPARATOR SCREW SEPARATOR MAINPLATE ASSEMBLY GATE ASSEMBLY COVERPLATE ASSEMBLY RAIL CRADLE ASSEMBLY UNDERSIZE LEVER MAGNET GATE ASSEMBLY MAGNET GATE ADJUSTER SCREW LOWER GATE PIVOT SPRING UPPER GATE PIVOT SPRING GATE PIVOT PIN WIPER LEVER SPRING WIPER LEVER WIPER

FIGURE 4 COIN ACCEPTOR — EXPLODED

FrOLERANCES UNLESS A OTHERWISE SPECIFIED FRACTIONS DEC ANGLES Mleakows Ga Wies, r nNe-

+ * + ari PEP tor

a A DRAWING NO. FIGURES COIN FACE PLATE [G-O004

  • DO NOT SCALE DRAWING |sHEET /OF | ‘BISHOP GRAPHICS, INC. REORDER NO. 20520
Page 15

REVISIONS DESCRIPTION

COMPONENT

SIDE

he THIS POSITION NOTUSED

7 FUNCTION

\8O SECONDS it 20 SECONDS ITOLERANCES UNLESS 90 SECONDS OTHERWISE SPECIFIED WN CAM mavens oe DEC. ANGLES| SUNNYVALE, CA. 94086 6O SECONDS _ SWITCH gt Vy amie LoGic

2 COIN GAME Bere LAZER COMMANDO

co = be /zzhe| oe DRAWING NO. CTT coro a ons ar 7377] BISHOP GRAPHICS/ACCUPRESS REORDER NO. A-7071.

Page 16

Lev WwW BWA OY DY.

  • wes EL Map £-70yes ir over —'wag 7-80 33-9 wy

—*oin tf - 3

LAZER COMMAND WIRE HARNESS D/AGRAM —79k IN tIS [Phin 2w-915

  • "N10 2-5 “Min was ies IN-ES — 22% ov-11s — ane 24S — Lem ormtp 2s tglgy: 9

‘SIZE | CODE IDENT NO. | DRAWING NO. “19k 94-1S—J 2854 /e-1p “A 2N-0f 5 —— ° Pen ie Gm 9-9 S — 5 W251 —

24m BW-£15 ——|

DO NOT SCALE DRAWING “og av 8S ——t Wad 1/-1r

pm DN-4S—} oxy WN FINE RIGHT CONTROL

%

wre im AP a fae sing WODLS rg "WD-5 S— Sinem BU 1g OD 15-

"UNLESS OTHERWISE SPECIFIED

BREAK AND DEBURR ALL SHARP EDGES, or a e ae woes 24h 8-10 RIGHT RUN

SWITCHES

Jw “fm wrog-e > id yr a1- 10°

Te]? [a5 ]ar COIN EXPERT

wpe Tale 3 [F228 woes — ° YBig Hoa -£S

MaO $1 -1°-

\—"w10 ow -§ S —~ COIN COUNTER ry bod ° p29 6-1 0 a lym g1=10-

‘NID 9 E Diy on LEFF RUN a ° / J St Yer wosrs ‘oiN /- IP,

ae YEL. LEFT CONTROL

‘M39 OF-IP re 3-Ir

UL __) Ri str com ny,

Jie

® aay, |

Page 17

a) 9) IDE, 2 PLACES ; UO Bras 27 ei

/ '

L COMMON GND)

SECTION A-A (T&M | NOT SHOWN FOR CLARITY.

2 PLACES (// es

SECTION D-D

NOTES: REMOVE THE N.O. (A) CONTACT PIN FROM 1TEM 6 eae /TEM 18 ONTO 1TEN1 10 € SHRINK BEFORE ASSY BY CUTTING, BEFORE INSTALLING /7EM 10 INTO ITEM 1. FEED THE Z WIRES FROM HARNESS 027-0025 {[T-> SEAL ALL THREAD JUNCTIONS W/TH REF THRU. ITEM 1, INSTALL TWO ITEM I PIECES, 17TEM 20 AS REQ'D. CONNECT WIRES TO. 17EM 6, SHRINK ITEM, 16 4 INSTALC /TEM 11 PIECES Ateted THE CORNER THREAD ITEM © (NTO 17EM 1, TIGHTEN USING RADIUS TOWARD ITEM 17,2 PLACES. SPECIAL TOOL B/N o INSTALL /TEM 15 WITH CURVATURE AS SHOWN. Séé LIST OF MATERIALS 112-0083 TEM THE HOS OF THE ITEM 4 PIECES AS SHOWN INSTALL ITEM 12 WITH CORNER RADIVS

INSTALL THE ITEM 4 PIECES WITH. THE HOOKS ASAWAY FROM 1TEM 17.mere
SHOWN #€ 7O THE DIMENSION SHOWN.PECOAT (TEM 17 ALE OVEE WITH bTEM 21 BEFOREeX*X
COAT THE HOLE IN ITEM 3 # THE WHEEL OFINSTALCATION (NTO (TEM 2.WVIPE AWAY EXCESS{[ wma | pare |
THE ITEM § PIECES WITH / TEM /9, AS REQD.(TEM 21 AFIER ASSEMBLY 13 COMPLETED,VD: 0/071