Super Hang On
Super Hang-On (Mega-Tech) (Sega, 1989) · Manual · 44 pages · 20 sections · original scan
UPRIGHT TYPE
OWNER’S MANUAL
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CONTENTS
INTRODUCTION TO THE OWNER'S MANUAL.........000:0..ccccseseeeeeeeeaee HANDLING PRECAUTIONS ...........ccecccsseceseecceeneeeeeeeeeueee PREVENTION OF COUNTERFEITING AND CONVERSION ... PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION .. EXTERIOR VIEW OF THE GAME 1. INTERIOR VIEW OF THE GAME 2.. ADJUSTING THE "SERVICE" SWITCH . DIP SWITCH SETTING............ GAME DIFFICULTY SETTING.. REMOVING THE HANDLE COVER. REMOVING THE HANDLE UNIT...........
- HANDLE'S CENTERING ADJUSTMENT...
- ADJUSTING THE ACCELERATOR AND BRAKE CONTROL ("VOLUME"
- REPLACING THE ACCELERATOR RELATED PARTS..
- REAR ASSEMBLY 14, EPROM/ROM LOCATION .. 15, SELF-TESTING
- PARTS CATALOG...
- SCHEMATIC DIAGRAM... bale ae) COUDANRWWNHNHE $0 90 Soy
SPECIFICATIONS
INSTALLATION SPACE : 30.7 in. (78 cm) W x 35.4 in. (90 cm) D HEIGHT : 65 in. (165 cm) POWER : 190W WEIGHT : 90 kg (198 Ibs)
INTRODUCTION TO THE OWNER’S MANUAL
SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSI, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the SUPER HANG-ON, a new SEGA product. The manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system.
-l-
- HANDLING PRECAUTIONS
When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely.
- Be sure to turn the power off before working on the machine. ¢ To insert or pull out the plug quickly is dangerous.
- It is necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc. in a manner so as to be dangerous. Make sure that grounding connections are made safely at the position where so specified.
- Do not use any fuse that does not meet the specified rating. + Make complete connections for the IC board and other connectors. Insufficient insertion is very dangerous.
Also, for the IC board circuit inspections, only the logic tone is allowed. The use of a tester is not permitted, so be careful in this regard. After confirming that there are no irregularities, turn the power ON.
- PREVENTION OF COUNTERFEITING AND CONVERSION LABELLING To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or by converting, selling or using such products or printed circuit boards.
ORIGINAL SEAL LICENSE SEAL The following seal is put on the The following seal is put on the kits, such as machines manufactured by SEGA. the printed circuit boards, of SEGA products.
SEGA
+ (FUP NE) + [ORIGINAL SEAL)
ORIGINAL = SUPER HANG-ON No Fide taT uBR TI
COPYRIGHT NOTICE This SEGA product has the copyright notice as follows: © SEGA 1987
This signifies that this work was disclosed in 1987 and is the property of SEGA ENTERPRISES, LTD.
- PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION
The SUPER HANG-ON is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing it in places mentioned below so as to ensure proper usage: + Places subject to rain or water leakage, or condensation due to humidity.
- In the proximity of an indoor swimming pool and/or shower.
- Places subject to direct sunlight. + Places subject to heat sources from heating units, etc., or hot air. + Vicinity of highly inflammable/volatile chemicals or hazardous matter. ¢ Sloped surfaces. + Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. + Places subject to any type of violent impact.
- Dusty places.
- EXTERIOR VIEW OF GAME 1
TOP HOOD REAR
Crecente SPEAKER speaxeh_——@ Fe rim (130-5018) ASSY CLR DISPL "20" (200-5095)
ASSY HANDLE (HG-50001)
COIN CHUTE DOOR
CASH BOX DOOR
- INTERIOR VIEW OF GAME 2
- ADJUSTING THE "SERVICE" SWITCH
The layout as shown can be viewed by opening the service door.
SERVICE DOOR SERVICE SW.
TEST SW.
@) VOLUME
|~—+—. ASSY COIN CHUTE 2 DOOR USA 25¢ TWIN
COIN METER
INSTRUCTIONS
1, VOLUME ADJUSTMENT The volume of the speaker inside the cowl can be adjusted.
- SERVICE SWITCH Used for the purpose of servicing and increasing the credits without registering on the meter (this allows you to check the game).
- TEST SWITCH For operating this switch, see SELF-TESTING.
- DIP SWITCH SETTING
+ GAME PRICE SETTING
DIP SWITCH #A COIN SWITCH #1
COIN SWITCH #2 OPTION r1f2e{[s|]4f{s|{e6f]7]e
| 1COIN | 1 CREDIT | oFF| | oFF| OFF} OFF| OFF] OFF| OFF | OFF |
| 1COIN | 2 CREDITS | ON | OFF| OFF] OFF| ON | OFF| OFF | OFF | |
| 1COIN | 3 CREDITS | OFF | ON | OFF] OFF| OFF| ON | OFF | OFF | |
| 1COIN | 4 CREDITS | ON | ON | OFF! OFF| ON | ON | OFF| OFF | |
| 1COIN | 5S CREDITS | OFF | OFF| ON | OFF| OFF| OFF] ON | OFF | |
| 1 COIN | 6 CREDITS | ON | OFF] ON | OFF] ON | OFF| ON | OFF | |
| 2COINS. | 1 CREDIT | OFF | ON | ON | OFF| OFF| ON | ON | OFF | |
| 3.COINS | 1 CREDIT | ON | ON | ON | OFF] ON | ON | ON | OFF | |
| 4COINS | 1 CREDIT | OFF | OFF | OFF] ON | OFF] OFF} OFF] ON | |
| 2COINS | SCREDITS | ON | OFF] OFF} ON | ON | OFF} OFF] ON |
2COINS 1 CREDIT 4COINS 2CREDITS
| Scone | py | OFF | ON | OFF} | ON | OFF} ON | OFF| ON |
COINS 4 CREDITS 2COINS + CREDIT
| scons | BCREDITS | ON | ON | OFF] ON | ON | ON | OFF] ON |
1COIN 1 CREDIT 2COINS 2CREDITS
| 3COINS | CREDITS | oFF | OFF| ON | ON | OFF| OFF! ON | ON |
4COINS: 4 CREDITS S5COINS 6 CREDITS 1COIN 1 CREDIT 2COINS 2 CREDITS
| COINS | Seacbae | ON | OFF| ON | ON | ON | OFF| ON | ON |
4 COINS SCREDITS 1COIN 1 CREDIT
| Scone | SCREDITS | oFF| ON | ON | ON | OFF] ON | ON | ON |
FREE PLAY ON | ON | ON | ON | ON | ON | ON | ON COIN SW. #1 COIN SW. #2
+ OPTION SWITCH SETTING
DIP SWITCH #B
| OPTION | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| ADVERTISE | OFF | OFF | ||||||
| SOUND | ON | ON |
NORMAL OFF | OFF
| GAME | EASY | ON | ‘OFF | OFF |
| DIFFICULTY | HARD | OFF | ON | |
| HARDEST | ON | ON |
NORMAL oFF | OFF
| TIME | EASY | ON | OFF |
| ADJUST | HARD | OFF | ON | |
| HARDEST | ON | ON |
- GAME DIFFICULTY SETTING
In this game, by using the DIP SWITCH B on the CPU BOARD, the 4 difficulty levels can be set for each of the following: 1 Other bikes' appearance frequency 2 Play Time adjustments. When shipping, the difficulty level of 1 is setat HARD, 2 is set at NORMAL. In actual play, however, a setting to a more difficult or easier level depending on the player's skill levels can be made.
- OTHER BIKE'S APPEARANCE FREQUENCY (SWITCH 2,3)
SWITCH NO. | OTHER BIKE'S DIFFICULTY
| 2 | 3 | APPEARANCE FREQUENCY| | LEVEL |
OFF | OFF NORMAL *
| ON | OFF | 30% less than normal | EASY |
| OFF | ON | 40% more than normal | HARD |
| ON | ON | 80% more than normal | HARDEST |
- When Shipping
- PLAY TIME ADJUSTMENT SWITCH (SWITCH 4, 5)
TT CLASS. PLAY TIME PER STAGE (SEC) teva
| 1J2]a]4]sle | 7 | |e] | 9 | 10]1|12] 19] 4] 15] 16] 17 ]18 |
BEGINNER 50| 25| 32) 32] 30| 32 JUNIOR 50| 25| 32) 32| 30| 32) 32] a2 32) 30 NORMAL 2k OFF | OFF) SENIOR 50} 25} 32/ 32) 30/ 32] 32) 32] 92| 30 | 92/32] 92) 92 EXPERT 50} 25| 32/ 32] 30/ 32] 32] 32) 32| 30 | 32/32] 32 | 32] 30] 32 | 32 |22 BEGINNER §5| 25| 33] 33] 30] 33 | JUNIOR: 55] 25) 33) 33} 30) 33) 33] 33] 33) 30
| OFF | ON | seNioR | 85| 25] 33] 33| 30| 33| 33] 33] 33] 30 | 33/39 | 33] 23 | EASY: |
EXPERT 55] 25| 33) 33| 30/ 33) 33] 33) 33) 30 | 33/33] 33 | 33] 90/33 | 33 | a3 BEGINNER 45| 25/ 31| 31) 30| 31 JUNIOR: 45) 25) 31] 31] 30) 31] 31] 31/ 31/ 90
| ON | OFF] SENIOR | 45| 25] 31| 31) 30] 31] 31} 31] 31] 30 | 31] 31| 31 | 31 | HARD |
EXPERT 45) 25) 31) 31) 30) 31] 31/ 31] 31) 30 | 31 | 31 | 31/31 | 30] 31 | 31 [31 BEGINNER 40| 25/ 30/ 30) 30) 30 OR x 30,
| ON] ON | ENON | 40] 28| 20] 30] 20| 20] 30] 20] 20] 20 |20| 20) 20] 20 | HARDEST: |
EXPERT 40| 25{ 30| 30| 30| 30| 30} 30} 30} 30 | 30 | 30} 30 | 30| 30} 20 | 20 | 20
- When Shipping
DIE SW-NO: DIFFICULTY LEVEL
| 5 | 4 | 3 | 2 |
OFF | ON | OFF | ON | 1 OFF | OFF | OFF | ON | 2 EASY
| ON | OFF | orF | [ON | 3 | ft |
| ON | |-ON | OFF | [ON [| 4 |
OFF | ON | OFF | OFF | 5 OFF | OFF [| OFF | OFF | 6 ON | OFF [ OFF | OFF | 7
| ON | [ON | OFF | OFF | | 8 | ||
| OFF | |ON | [ON | | OFF | 9 | | - |
OFF | OFF | ON | OFF | 10 * When Shipping
| ON | OFF | [ON | OFF | | 11 | |
| ON | |-ON | [ON | OFF | | 12 |
|__ OFF [ ON | ON | ON [ 13
| OFF | OFF | ON | | ON | 14 | HARDEST | ||
| ON | | OFF | [ON | ON | | 15 | u |
| ON | | ON | | ON | | ON | | 16 |
“Je
- REMOVING THE HANDLE COVER
- When adjusting the ACCELERATOR, BRAKE, etc., remove the HANDLE COVER by using the following procedure:
TAMPERPROOF WRENCH 540-0009-01
HANDLE COVER HG-5050
SCREW B SCREW B
SA \«— SCREWA ‘ey = (TAMPERPROOF SCREW) Les ees \ BRACKET B BRACKET A % _ HG-5049 be LIMES ES
SCREW A
(TAMPERPROOF SCREW) ‘screw B (TAMPERPROOF SCREW)
M5 x 12
DISASSEMBLING PROCEDURE
- Remove 4 SCREWS A which fasten BRACKET A and BRACKET B by using the TAMPERPROOF WRENCH (M5).
- Remove 4 SCREWS B which fasten the HANDLE COVER by using the TAMPERPROOF WRENCH (M5).
- The HANDLE COVER can be detached from the HANDLE UNIT in accordance with
the above procedures 1 and 2 . It is completely removable from the MAIN CABINET
by pulling out the CONNECTOR (WHITE 4P).
- REMOVING THE HANDLE UNIT
SCREW "A" © __, = SCREW "A"
TAMPERPROOF WRENCH 540-0009-01
- HANDLE'S CENTERING ADJUSTMENT
- Display the following SELF-TEST MODE screen.
[e) o) DIAGNOSTIC. INPUT TEST COIN#1 START & e+ 6
COIN #2 SERVICE y SPUR GEAR
S.C. SW. VARIABLE cs ‘ =ANGLE DATA VALUES ACCEL DATA BRAKE DATA _ / PINION GEAR
Secure the set screws when the on-screen ZG
variable value becomes 80H (+4 steps). we a
sf Pi) “re VOLUME 7CH 7DH 7EH 7FH 80H 81H 82H 83H 84H BRACKET SCREW "A"
DISASSEMBLING AND ADJUSTMENT PROCEDURES
Loosen 2 SCREWS A and horizontally move the VR BRACKET to make the backlash adjustments between the pinion gear and the spur gear.
Manually turn the pinion gear to ensure that the variable value in the TEST MODE becomes approximately 30H, make the backlash adjustments and then fasten 2 screws A.
- ADJUSTING THE ACCELERATOR AND
BRAKE CONTROL ("VOLUME")
VOLUME 5K B TYPE a" 290-5130 VOLUME (FOR ACCELERATOR) ACCELERATOR WIRE HOLDER
ACCELERATOR WIRE
AVe \e\e\t CD tb ail Wah = & Ww)
STOPPER , on t=
VOLUME SHAFT PINION GEAR (FOR BRAKE) BRAKE WIRE
Make the VOLUME adjustments as follows:
BRAKE
1, When the brake lever is operated, the brake wire is pulled and the pinion gear turns approximately 180 degrees.
Return the brake lever, fully turn the VOLUME shaft clockwise at the position where the brake wire comes into contact with the stopper and secure the pinion gear with the 2 M4 x 4 screws.
Adjust the length of the brake wire with the adjustment nut to ensure that the pinion gear turns 180 degrees.
ACCELERATOR
1. When the accelerator grip is operated, the accelerator wire turns to cause the VOLUME SHAFT to rotate approximately 180 degrees.
At the position where the accelerator grip is retuned, fully turn the VOLUME SHAFT clockwise and secure the accelerator wire holder with 2 M4 x 4 set screws.
-ll-
- REPLACING THE ACCELERATOR RELATED PARTS
CASE A (HG-5015) RIP CASE CAP NUT 7 (M5) i; @ (HG-5012) CASE RETAINER (HG-5017)
as SPACER
\ (HN-1045)
« ~ | TAPPING SCREW (M3 X 8) eq
GRIP (107-0009X)
TAMPERPROOF SCREW SPRING ® ff (HG-5018X) (M5 X 25) CASE B (HG-5016)
- To replace the grip, remove it in the direction of X. (It can be easily taken out by partially cutting it with a cutter.)
- To replace the spring inside the accelerator case, remove the case, the 3 M3 x 8 tapping screws that secure the case retainer and then the 2 MS x 25 tamperproof screws, in a manner to ensure disassembly as shown above.
- When the spring has been completed, display the following SELF-TEST MODE screen.
When the accelerator is returned, make sure that the DIAGNOSTIC variable value becomes OOH at the set position. The INPUT TEST allowable range of the variable values is OOH - 04H. COIN #1 START COIN #2 SERVICE S.C.SW. VARIABLE = ANGLE DATA _ VALUES ACCEL DATA BRAKE DATA
- REAR ASSEMBLY
Pow TAMPERPROOF WRENCH 540-0009-01
SCREW "A" AN
14, EPROM/ROM LOCATIONS
oS rap
L/ LUTTT), LT va (A) 7 (B)
GAME BD SUPER HANG-ON (834-6277-01, 834-6277-03, 834-6277-05)
A. CUP BD SUPER HANG-ON (837-6278-01, 837-6278-03)
Tce
Ci} [ica7]
ics8] [ic7e ici) ficisa 1C57] 1¢75) 10117] 1 132! ms i t aed teed bana Gees
B. VIDEO BD SUPER HANG-ON (837-6279, 837-6279-01, 837-6279-02)
os cas g RRREE
A titi [icieyic 6
Ls
GAME BD 834-6277-01 834-627-038 834-6277-05 SECURITY WISECU WiSECU WISECU CPU BD 837-6278-01 (U/R) 837-6278-01 (U/R) 837-6278-01 (UR) Ic 118 EPR-10788 EPR-10788 EPR-10788 MAIN I 117 EPR-10635A EPR-10635A EPR-10635 A PROGRAM Ic 133 EPR-10789 EPR-10789 EPR-10789 Ic 132 EPR-10637A EPR-10637A EPR-10637A suB 1c58 EPR-10790 EPR-10790 EPR-10790 PROGRAM IC57 EPR-10791 EPR-10791 EPR-10791 IC 76 EPR-10792 EPR-10792 EPR-10792 1075 EPR-10793 EPR-10793 EPR-10793 Ic47 EPR-10642 EPR-10642 OPR-10642 ROAD eit Ic66 EPR-10643 EPR-10643 OPR-10643 s \c67 EPR-10644 EPR-10644 OPR-10644 © | paral 1o68 EPR-10645 EPR-10645 OPR-10645 U Ic69 EPR-10646 EPR-10646 OPR-10646 N Ic70 bY to71 PROGRAM Icas EPR-10649A EPR-10649A EPR-10649 A 837-6279 837-6279-01 837-6279-02 VIDEO BD (EP-ROM TYPE) (MASK ROM TYPE) (ONE TIME ROM TYPE)
IC 56 EPR-10650 EPR-10650 OPR-10650 SCROLL 155 EPR-10651 EPR-10651 OPR-10651 Io54 EPR-10652 EPR-10652 OPR-10652 Ics EPR-10675 MPR-10794 OPR-10675 Ic7 EPR-10676 OPR-10676 Ic6 EPR-10677 MPR-10795 OPR-10677 Ic5 EPR-10678 OPR-10678 Io4 EPR-10679 MOR-10796 OPR-10679 Ic3 EPR-10680 OPR-10680 Ic2 EPR-10681 MPR-10797 OPR-10681 Ic1 OBJECT Ic 16 EPR-10682 MPR-10798 OPR-10682 Ic 15 EPR-10683 OPR-10683 ic14 EPR-10684 MPR-10799 OPR-10684 Ic 13 EPR-10685 OPR-10685 Ie12 EPR-10686 MPR-10800 OPR-10686 ict EPR-10687 OPR-10687 Ic 10 EPR-10688 MPR-10801 OPR-10688 Ico
(EP-ROM (MASK- ROM (ONE TIME
TYPE) TYPE) ROM TYPE)
- SELF TESTING
The main purposes of these tests are to check the operations of the game boards, to find the defects if any, to adjust the monitor colors properly, and to make sure the sounds are produced satisfactorily. It is also performed to indicate the assignments of the dip switches, check bookkeeping functions, etc.
KIND OF TESTS
1.
2.
1. Memory Test:
Input Test:
Output Test:
Sound Test:
CRT Test:
Dip Switch Assignment:
Bookkeeping:
Backup RAM
Clear:
EXIT To check the EPROM programs and the map area of the RAM's.
To check the machine's inclining angle and to test the operation of the accelerator, brake, supercharger switch, coin switches, etc.
To test the operation of the lamps.
To check the quality of the sounds produced by the PCB and the video disc, and to adjust the balance of the speakers.
To check if the colors on the monitor are displayed correctly.
To indicate each dip switch assignment.
To indicate information data on average score, average play time, etc.
When the power is turned off, a backup battery system automatically takes over, thus allowing the continuous storage of all bookkeeping data. Using this item will enable you to clear said data.
See page
TEST OPERATION
- Push the test switch and Fig. 1 will be shown on the screen.
- Select CONTINUE or INDIVIDUAL by using the START button.
DIAGNOSTIC [INDIVIDUAL]
- Move the accelerator to bring the arrow to the desired position.
MEMORY TEST SELECT BY ACCELERATOR PUSH TEST INPUT TEST OUTPUT TES SWITCH (Select the desired test item by using T the accelerator and push the test switch button.) SOUND TEST C.R.T. TEST DIP SWITCH ASSIGNMENT BOOKKEEPING BACK UP RAM CLEAR EXIT SELECT BY ACCELERATOR PUSH TEST BUTTON! FIG 1
[CONTINUE]:
¢ _ Bring the arrow sign (by operating the ACCELERATOR) to CONTINUE first, and move it to one of the tests to start. Push the TEST button, and the tests will be performed in order, one by one, starting from the test where the arrow was originally set to the EXIT.
¢ — Ifthe START button is pushed when the arrow is at CONTINUE, it will change to INDIVIDUAL. Pushing it again returns it to CONTINUE.
[INDIVIDUAL]:
¢ _ If the arrow is at INDIVIDUAL first and brought to a certain test which you want to conduct, only that test is performed by pushing the TEST button.
- When each test is finished in the case of CONTINUE, push the TEST button, and it will automatically go into the following test. If the TEST button is pushed in the
case of INDIVIDUAL, Fig. 1 is shown. If you want to end the test mode at this
time, bring the arrow to EXIT and push the TEST button, and it will return to the ADVERTISEMENT mode.
- TEST ITEMS
- Memory Test:
DIAGNOSTIC MEMORY TEST ROMS TEST **RAMS TEST **
| IC.133 GOOD | IC. 29 | GOOD | 1C114 |
| IC.132 GOOD | IC. 30 GOOD | 1IC129 | |
| IC.118 GOOD | IC. 63 GOOD | IC. 55 | |
| IC.117 GOOD | IC. 50 GOOD | IC. 73 | |
| IC. 76 GOOD | IC. 64 GOOD | IC. 54 | |
| IC. 75 GOOD | IC. 51 | GOOD | IC. 72 |
| IC. 58 GOOD | IC. 75 | GOOD | IC. 20 |
| IC. 57 GOOD | IC. 74 | GOOD | IC. 21 |
| 1C.115 | GOOD | IC. 38 | |
| IC.130 | GOOD | IC. 39 |
Indication of "GOOD" following the IC No. means the IC is all right. Push the TEST button to proceed to the following test item.
- Input Test:
DIAGNOSTIC INPUT TEST
COIN #1 START COIN #2 SERVICE S.c. SW.
= ANGLE DATA 80H $.C. SUPERCHARGER ACCEL DATA 00H BRAKE DATA 00H
- Operate the dip switches. When "ON" is indicated at the right side of a certain tested item, the item is "OK".
. If the data value decreases when the bike is inclined to the right, or increases when it is inclined to the left, the testing is OK (the data is indicated in the form of hexadecimal values). Make the adjustment in a manner so that in the static condition the value shows 80H (within 7CH - 84H). (Mininium value: To clear 3C. Maximum: To be in excess of BE).
¢ If the data value increases when the accelerator/brake is applied and the value ranges between 00H and 04H when it is returned to its original position, then the item test is OK. (In the case of the accelerator, make sure that the maximum value is in excess of 91H.) (In the case of the brake, make sure that the maximum value is in excess of A7H.)
When the test is ended, push the TEST button.
- Output Test:
DIAGNOSTIC OUTPUT TEST
START LAMP
If the start LAMP lights up, it is functioning properly. Push the TEST button when the testing has been completed.
- Sound Test:
DIAGNOSTIC SOUND TEST MUSIC 1 10. SAFETY ZONE MUSIC 2 11. CRASH MUSIC 3 12. ALARM 1 MUSIC 4 13. ALARM2 MUSIC 5 14. ALARM3 MUSIC 6 15. ALARM4 MUSIC 7 16. MY BIKE COIN IN 17. OTHERBIKER REBOUND 18. OTHERBIKEL
SELECT BY ACCELERATOR PUSH START BUTTON! 1. 2. 3. 4. 5. 6. 7. 8. 9.
When the test has been completed, push the TEST button.
- C.R.T. Test:
YELLOW
GREEN
DIAGNOSTIC LIGHT BLUE
C.R.T.TEST RGB COLOR BAR
BLACK FT Reo] NS [tue [Pink] 7 [WHITE
= Copy C.R.T.POSITION CHECK
When the test has been completed, push the TEST button.
- Dip Switch Assignments:
DIAGNOSTIC DIP SWITCH ASSIGNMENTS
| 1 | 2 | 3 | 4 | #5 | 6 | 7 | 8 | |
| DIPSW.A | OFF | OFF | OFF | OFF | OFF | OFF | OFF | OFF |
DIPSW.B = OFF OFF OFF OFF OFF OFF OFF OFF
| A 1234 COIN SW#1 | 1 COIN | 1 CREDIT |
| A 5678 COIN SW#2 | 1 COIN | 1 CREDIT |
| Bi | ADVERTISE SOUND | OFF |
| B23 | GAME DIFFICULTY | NORMAL |
| B45 | TIMEADJ. | NORMAL |
- Bookkeeping:
DIAGNOSTIC BOOKKEEPING
COIN CHUTE #1 0 Usage frequency of coin chute 1
| COIN CHUTE #2 | 0 | Usage frequency of coin chute 2 | ||
| COIN CREDITS | 0 | Number of coin credits | ; | ; |
| SERVICE CREDITS | 0 | Usage frequency of service switch |
Number of credits
| pee CHE | TS | 6 | Operating time (hour-minute-second) |
ToTaLTiIMe OHOmOs PUSH START BUTTON!
- — Only the data that falls within the range of up to999H 59M 59S can be memorized. The above screen indication is for testing. When the tests are finished, push the START button and the following will be shown:
DIAGNOSTIC BOOKKEEPING
NUMBER OF GAME AVE. SCORE TOP SCORE LOW SCORE ** GAME TIME ** TOTAL AVERAGE LONGEST PUSH START BUTTON!
DIAGNOSTIC. BOOKKEEPING TIME REPORT TO MIN. TO MIN. TO MIN. TO MIN. TO MIN. TO MIN. TO MIN. TO MIN. MIN. ONOMNSRWONM=AO0 OCONDAMAWNY < m D COCO OADWO
PUSH START BUTTON!
Every time the start button is pressed, the bookkeeping test display is repeated. When the test is finished, push the TEST button to end the test (in the case of "INDIVIDUAL", however, the test mode returns to Fig. 1 first).
+ If any data exceeds the bookkeeping function's capacity, "OVERFLOW" will be indicated on the screen and result in the stoppage of said function. At this time, turn the power OFF and tur it back ON again for reuse.
- Backup RAM Clear:
To clear the data, bring the arrow to "YES" and push the TEST button.
DIAGNOSTIC
BACKUP RAM CLEAR > NO YES
SELECT BY BRAKE PUSH START BUTTON!
When the test is finished, push the TEST button to end the test (in the case of "INDIVIDUAL", however, the test mode returns to Fig. 1 first).
- EXIT:
In the state as shown in Fig. 1, operate the steering to bring the arrow to EXIT and push the TEST button. The self-testing will then end and return to the ADVERTISEMENT mode.
- PARTS CATALOG
1 TOP ASSY SUPER HANG-ON U/R USA (HG-00001)
2 ASSY CABINET U/R USA (HG-10001)
OO
4 ASSY SUB CABINET (HG-1600)
SC) VOLUME/ TEST/ SERVICE
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
6 ASSY PWR SPLY EXPORT (HG-40001)
REC# PARTS. NO. DESCRIPTION
| 1 | HGI-10001 | ASSY, SUPER HANG ON | |
| 2 | 001-0410B | 4MM x 10MM BHSC | |
| 3 | 0001-0410P | 4MM x 10MM PPH | |
| 4 | 0001-0612S | 2 | #6 x 3/4 PH SQ SMS TYPE ABLK |
| 5 | 0601-0004 | 4MM SL WASHER | |
| 6 | 0601-0612 | 2 | WASHER, #6 TYPE B 5/16 OD BLK |
| 7 | 0611-0004 | 4MM LOCK WASHER | |
| 8 | 1050-0064 | MAIN SWITCH BKT | |
| 9 | 1170-0184 | TERM PLATE, 8P | |
| 10 | 1170-5131 | TERM PLATE, 5P | |
| onl | 1170-5131A | TERMINAL |
12 1500-0173 13 1500-01734 14 1500-0265 15 1500-02654 16 2000-5090 17 2200-0000 18 2200-5179 19 2600-0011-1 20 2800-0418 21 4200-5372-01 22 4211-1036-01 23 4211-1036-02 24 4211-1036-03 25 4211-1036-04 26 4211-1037-01 27 4211-1037-02 28 4211-1037-03 29 4211-6481 30 4211-6671 31 4211-6672 32 4211-6690-01 33 4211-6835 34 4810-0157 35 4810-0157A 36 5090-0039 37 5090-5028 38 5140-0034 39 5140-0040 40 5140-0043 41 5140-0064 42 5601-5106 43 6000-0078 44 6010-0001 45 6010-0042 46 6010-0429 47 HGO-1018 48 HGO-1027 CAP, 4700UF 50VOLT CLAMP, 4700UF SIZE CAP, 13000UF 25 VOLT CLAMP, 13000UF SIZE MONITOR, 19" RGB ASSY, COIN DOOR W/HARN. VOLUME CNTRL B-5K OHM AXIAL FLOW FAN BUSHING, STRAIN RELIEF OWNERS MANUAL SUPER HANG ON STICKER, US #1 RACING TEAM STICKER, US #2 SEGA EQUIPMENT STICKER, US #3 PY MANAGEMENT STICKER, REAR BLK STICKER, BLUE FRONT LEFT STICKER, BLUE FRONT RIGHT STICKER, BLUE FRONT TOP STICKER, SWITCH UNIT
| 49 | HGO-1036A | TOP HOOD REAR | |
| 50 | HGO-1036B | 1 | NUT PLATE |
| 51 | HGO-1036C | BACK PLATE | |
| 52 | HGO-1036D | NUT PLATE R | |
| 53 | HGO-1037A | TOP HOOD FRONT | |
| 54 | HGO-1042 | HINGE 186, CONTROL PANEL | |
| 55 | HG1-0001 | SHIELD BASE |
REC# PARTS. NO. DESCRIPTION
56 HG1-0005 57 HG1-1016D BKT, RF INTERFACE HOLDER NUT PLATE, DENOMINATION
| 58 | HG1-1037B | GLASS HOLDER BKT A |
| 59 | HG1-1037C | GLASS HOLDER BKT B |
| 60 | HG1-1037D | GLASS HOLDER BKT C |
| 61 | HG1-1038 | MOUNTING BKT HOOD REAR |
62 HG1-1039 63 HG1-1040 64 HG1-1601 65 HG1-1608 66 HG1-1609 67 HG1-1611 68 HG1-1612 69 HG1-1613 70 HG1-1614 71 HG1-1615 72 HG1-1616 73 HG1-1622 74 HGP-0001 75 KRO-1721 76 M00-1215Y 77 MX-1103-01 MOUNTING BKT, HOOD SIDE GLASS, 14 9/16 x 18 1/8 x 9/16 ASSY, CABINET HOLDER BKT, CONTROL PANEL CORNER PROTECTOR A, TRIM CORNER PROTECTOR REAR LEFT CORNER PROTECTOR REAR RIGHT CORNER PROTECTORE, TRIM ORNAMENT SASH RIGHT ORNAMENT SASH LEFT CORNER PROTECTOR FRONT, TRIM HINGE 148, DOOR ASSY. PACKAGE SW BKT A.C. CORD COVER 1x25 PRINTED
| 78 | MX-1103-02 | 2x25 PRINTED |
| 79 | MX-1103-03 | 3x25 PRINTED |
| 80 | NR1-1078 | AIRVENT |
| 81 | SGMO-2675 | POLYETHYLENE BAG |
| 82 | SGMO-3640 | POLYETHYLENE COVER |
| 83 | TBO-3003 | T.V. MASK 20 |
| 84 | 008-0416 | TMP PRF SCR TH BLK M4 x 16 |
| 85 | 008-0516 | TMP PRF SCR TH BLK M5 x16 |
| 86 | 009-0825 | TMP PRF SCR BH BLK M8 x 25 |
| 87 | 107-0009X-1 | GRIP ACCELATOR (SPARE) |
| 88 | 117-5123 | NAME PLATE |
| 89 | 130-5018 | SPEAKER 8 OHM 10 W, SHIELDED |
| 90 | 211-5212 | CONN FEM 20P |
| 91 | 211-5216 | CONN FEM 12P |
| 92 | 211-5220 | CONN FEM 25P |
| 93 | 220-5130 | VOL CONT B-5K OHM (SPARE) |
94 350-5104 95 390-0116 96 400-5058 MOTOR DC12V 4500 RPM (SPARE) LAMP WEDGE BASE 14V (SPARE) SW RGLTR 90-130V 5V 10A MOANNNNNAAN BABB ee eens asa N OMe anaanns ssa Nasa Naan asanNaAaaaa
| 97 | 421-5800-59 | ORIGINAL SEAL |
| 98 | 421-6119-91 | STICKER FCC |
| 99 | 421-6120 | STICKER SEGA USA |
| 100 | 421-6709 | STICKER SERVICE INFO |
| 101 | 421-6799 | STICKER HGL |
| 102 | 421-6801-S | STICKER HGS |
| 103 | 421-6806-S | STICKER HGM |
| 104 | 421-6826-01 | STICKER BS |
| 105 | 421-6826-07 | STICKER RK |
| 106 | 421-6826-08 | STICKER SPC |
| 107 | 421-6826-09 | STICKER KEIHIN |
| 108 | 421-6826-10 | STICKER HU TEK |
| 109 | 421-6827 | ADJ INSTR SH SUPER HANG ON |
| 110 | 421-6836-S | SIDE STRIPE STICKERL |
| 111 | 421-6837-S | SIDE STRIPE STICKERS |
REC# PARTS. NO. QTy DESCRIPTION
| 112 | 421-6838 | STICKER HG SEGA 80 |
| 113 | 421-6839-S | STICKER HG SEGA 26 |
114 421-6954 115 422-0191-01 116 509-5003-03 117 540-0006-01 118 §40-0007-01 119 54-0009-01 120 540-0015-01 121 600-5463 122 600-5464 123 600-5465 STICKER SER NO. INFO PLAY INSTR SH HG ENG SW PB 1T (SPARE) WRENCH FOR TAMP SCR M4 (SPARE) WRENCH FOR TMP SCR M5 (SPARE) WRENCH FOR TMP SCR M8 (SPARE) WRENCH FOR TMP SCR M6 (SPARE) CONN FEM 20P FEM 10Px2 CONN FEM 50P FEM 25P, 21P CONN FEM 12P FEM 4P, 6Px2
Br er
| 124 | 600-5472 | ASSY, EXT 21P |
| 125 | 834-6277-06 | GAME BD SUPER HANG ON U/R |
| 126 | 839-0035-01 | POWER AMP |
| 127 | 839-0048 | SSR BD MOTOR |
| 128 | 839-0079 | FILTER BD SUPER HANG ON |
| 129 | HG-50001 | ASSY HANDLE |
| 130 | HG-5018X | TORSION SPRING (SPARE) |
| 131 | HG-5042 | BRAKE WIRE S (SPARE) |
| 132 | HG-5051 | EXT SPRING (SPARE) |
| 133 | SGB-1035X | KEY BAG |
® Ko © ® ® © ©
) ©® © Fy eS Wy: o—_
ae 7 ASSY HANDLE (HG-50001) (D-1/3)
aH =f BO oddoes aoa
addeosvo®
7 ASSY HANDLE (HG-50001) (D-2/3)
ITEM NO. PART NO.
1 HG-5020 2 HG-5031 3 HG-5032 4 HG-5033 5 HG-5034 6 HG-5035 7 HG-5036 8 HG-5037 9 HG—5038 10 HG-5043 11 HG-5044X 12 HG-5045X 13 HG-5046 14 HG-5012 15 HG-5015 16 HG—5016 17 HG-5017 18 HG-5009 19 601-5780 20 HN-5024X 21 HN-5065 22 HG-5050 23, HG-5047 24 HG-5048 25 TB-2007 26 MX-2019 27 HN-5042 28 HG-5049 29 HN-5044X 30 HN-5045 31 HN-5046 32 107-0009X 33 601-5419 34 MX-2020 35, MX-—2021 36 HG-5100 37 HG-5018X 38 421-6103
101 509-5050 102 310-5009 103 280-5092 104 220-5130 105 601-5003 106 280-5008 107 214-0081 108 390-0116 109 280-0400 110 509-5003-03
201 000-0308-FS 202 029-0130 203 029-0044 204 010-0306-F 205 010-0408-F DESCRIPTION
ASSY CENTERING WOODEN BASE FRONT PANEL HANDLE BASE SLIDE PLATE OUTER SLIDE PLATE INNER BUMPER HOLDER A BUMPER HOLDER B ASSY BRAKE CONT ACCLERATOR WIRE S REAR LID PROTECT TUBE HLDR PROTECTOR TUBE ASSY GRIP CASE ACCELERATOR CASE A ACCELERATOR CASE B CASE RETAINER VR JOINT GEAR 16 BUMPER SLIDE HOLDER MECHANISM COVER METER PLATE A METER PLATE B LAMP HOLDER BOARD SWITCH CASE STOPPER RING COVER A COVER B SPACER SPACER TUBE GRIP LEFT & ACCELERATOR ASSY LEVER TUBE HOLDER PROTECTOR W/TUBE ASSY VIBRATION TORSION SPRING STICKER START
PUSH BTN SWITCH IT YELLOW W/LAMP. INSL SPIRAL TUBE ID 99 RUBBER GROMMET 13x21x7 TAKIGEN NG—-79-K VOL CONT B-5K OHM FREE BUSH CORD CLAMP 215 WEDGE BASE SOCKET ASSY LAMP WEDGE BASE TYPE 14V 0.24A CLAMP CORD PLASTIC ID 15 PUSH BTN SWITCH IT 14.2? RED
M SCR PH W/FS M3x8 M SCR FH M6x12 M SCR FH M6x25 S-TITE SCR PH W/F M3x6 S-TITE SCR PH W/F M4x8
7 ASSY HANDLE (HG-50001) (D-3/3)
ITEM NO. PART NO. DESCRIPTION
| 206 | 028-0001 | SET SCR HEX SKT CP UNBR M3x4 |
| 207 | 028-0014 | SET SCR HEX SKT CP UNBR M4x4 |
| 208 | 028-0036 | SET SCR CONE POINT M4x8 |
| 209 | 008-0525 | TMP PRF SCR TH M5x25 |
| 210 | 008-0516 | TMP PRF SCR TH M5x16 |
| 211 | 010-0420-F | S-TITE SCR PH W/I M4x20 |
| 212 | 029-0121 | TAP SCR FH M3x8 |
| 213 | 054-0006 | U-NUT M6 |
| 214 | 050-0008 | HEX NUT M8 |
| 215 | 031-0860 | CRG BLT M8x60 |
| 216 | 059-0029 | CAP NUT TYPE 3 BLK M5 |
| 217 | 061-0008 | SPR WSHR M8 |
| 218 | 060-0008 | FLT WSHR M8 |
| 219 | 000-0516-S | M SCR PH W/S M5x16 |
| 220 | 006-3520 | W SCR FH 3.5x20 |
| 221 | 005-3516 | W SCR RH 3.5x16 |
| 222 | 008-0512 | TMP PRF SCR TH M5x12 |
| 223 | 008x0412 | TMP PRF SCR TH M4x12 |
| 224 | 054-0004 | U-NUT M4 |
| 225 | 030-0612 | HEX BLT M6x12 |
| 226 | 061-0006 | SPR WSHR M6 |
WIRE HARN EXT VR & START CONN PLUG AMP 9P WHITE CONN CAP AMP 4P RED CONN CAP AMP 4P WHITE TIE BELT 8mm WIRE HARN START SW CONN PLUG AMP 4P WHITE FASTON RCPT 110 TIE BELT 85mm WIRE HARN EXT TURBO CONN PLUG AMP 2P RED CONN CAP AMP 2P RED TIE BELT 85mm WIRE HARN TURBO CONN PLUG AMP 2P RED FASTON RCPT 110 TIE BELT 85mm CONN PIN AMP CONN SOCKET AMP WIRE HARN LAMP CONN PLUG AMP 2P YELLOW WIRE HARN EXT HANDLE LAMP CONN CAP AMP 2P YELLOW CONN PLUG AMP 2P YELLOW WIRE HARN EXT HANDLE MOTOR CONN CAP AMP 2P WHITE CONN PLUG AMP 2P YELLOW CLAMP CORD PLASTIC ID 10mm CORD CLAMP £10
8 ASSY CENTERING (HG-5020)
em Qe) TO)
OO © © © ©8®
8 ASSY CENTERING (HG-5020) (D-2/2)
ITEM NO. PART NO. DESCRIPTION
| 1 | HG~5021 | PILLOW BRACKET |
| 2 | HG-—5022 | CLICK ARM A |
| 3 | HG-5023 | CLICK ARM B |
| 4 | HG—5024 | SLEEVE |
| 5 | HG-5025 | SPACER |
| 6 | HG-5026 | CENTER ARM |
| 7 | HG-5027 | SHOULDER STUD |
| 8 | HG—5028 | EXT SPRING |
| 9 | HG-5029 | STOPPER |
| 10 | HG-5030 | VR BRACKET |
| rr | HN-5017 | HANDLE SHAFT |
| 12 | HN-5031 | GEAR BRACKET |
| 13 | 601-5423 | GEAR 1/6 |
| 14 | 601-5424 | GEAR 30 |
| 15 | CY-2307 | ROLLER |
| 101 | 100-5035 | BEARING #20 |
| 102 | 220-5130 | VOL CONT B-5K OHM |
| 104 | 601-0485 | ONE TOUCH COLLAR £=10 |
| 201 | 000-0420-FS | M SCR PH W/FS M4x20 |
| 202 | 030-0410 | HEX BLT M4x10 |
| 203 | 000-0514 | M SCR PH Msx14 |
| 204 | 031-0860 | CRG BLT M8x60 |
| 205 | 029-0129 | HEX SKT H CAP SCR BLK M6x25 |
| 206 | 054-0006 | U-NUT M6 |
| 207 | 050-0010 | HEX NUT M10 |
| 208 | 060-0010 | FLT WSHR M10 |
| 209 | 061-0010 | SPR WSHR M10 |
| 210 | 060-0004 | FLT WSHR M4 |
| 211 | 061-0004 | SPR WSHR M4 |
| 212 | 065-0008 | E RING 8mm |
| 213 | 069-0038 | FLT WSHR 12.2~22x0.5 |
| 214 | 059-0016 | HEX NUT M14 |
| 215 | 069-0019 | SPR WSHR M14 |
| 216 | 069-0045 | FLT WSHR M14 |
| 217 | 061-0008 | SPR WSHR M8 |
| 218 | 054-0005 | U-NUT M5 |
| 219 | 000-0406-S | M SCR PH W/S M4x6 |
| 220 | 028-0014 | SET SCR HEX SKT CP UNBR M4x4 |
| 221 | 050-0008 | HEX NUT M8 |
| 222 | 060-0008 | FLT WSHR M8 |
WIREHARN ANGLE CONN PLUG AMP 3P WHITE TIE BELT 85mm
9 ASSY BRAKE CONT (HG-5038)
ITEM NO.
OIA RwDe PART NO.
HG-5039 HG-5040 HG-5041 HG-5042 HG-5051 HN-5103 601-5251 601-5415
220-5130
000-0408-FS 010-0408-F 030-0525 054-0005 060-0005 069-0005 045-0005 000-0408-S 028-0014 DESCRIPTION
BRAKE CONT BRACKET STOPPER BRAKE WIRE STOPPER BRAKE WIRE S EXTENSION SPRING LEVER SHORT GEAR 1/8 GEAR 20
VOL CONT B-5K OHM
M SCR PH W/FS M4x8 S-TITE SCR W/F M4x8 HEX BLT M5x25 U-NUT M5 FLT WSHR M5 FLT WSHR 8.3-14.3x0.5 COT PIN 2x15 M SCR PH W/S M4x8 SET SCR HEX SKT CP UNBR M4x4 WIRE HARN ACCEL & BRAKE CONN PLUG AMP 4P RED TIE BELT 85mm CONN PIN AMP
10 ASSY VIBRATION (HG-5100) (D-1/2)
10 ASSY VIBRATION (HG-5100) (D-2/2)
ITEM NO.
wrm® HA RweNYH PART NO.
HG-5101 HG-5102 HG-5106 HG-5107 HG-5108 HG-5109 350-5104 HG-5110
100-5041 280-5078 280-5056
000-0408-S 000-0420 069-0007 054-0004 028-0001 029-0131 001-0410 DESCRIPTION
BRACKET ASSY VIBRATION CAM MOT HOLDER JOINT SPRING BOSS CLAMP MOTOR DC 12V 4500rpm HOLDER BRBCKET
BEARING NSK F6882Z RUBBER GROMMET 8x 14x8 ONE TOUCH COLLAR £=7.5
M SCR PH W/S M4x8 M SCR PH M4x20 F WSHR 4.4-16x1.6 U-NUT M4 SET SCR HEX SKT CP UNBR M3x4 M SCR PH W/S M2.6x10 M SCR FH M4x10 WIRE HARN MOTOR CONN PLUG AMP 2P WHITE TIE BELT 85mm
THsee “4 TET
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
SEGA ENTERPRISES, INC. (USA) 2149 Paragon Drive San Jose, CA 95131 Tel. (408) 435-0201 ©SEGA 1987