CATHODE RAY TOMES

Turtles In Time

Teenage Mutant Ninja Turtles: Turtles in Time (4 Players ver UAA) (Konami, 1991) · Manual · 20 pages · 43 sections · original scan

Page 1

a KONAMI:

nis

INSTRUCTION MANUAL

a Kowamr® is a trademark of Konami Industry Co., Ltd.

Page 2

T.M.N.T. Il PARTS LIST

Part #

063003

063100

063101

063200

063300

063301

063302

063303

063304

063305

063306

063400

40905

40901

40605

40615

# NIA

# NIA

# NIA

# NIA

30263

30264

30265

30266

30269

30270

30267

30268

30261

30262 Description T.M.NLT. I PCB. T.M.NT. t1 C.PO. T.M.N.T. Il Player Instruction T.M.N.T. Il Marquee T.M.N-T. Il Upper Right Side Decal T.M.N.T. Il Upper Left Side Decal T.M.N.T. Il Middle Right Side Decal T.M.N.T. Il Middle Left Side Decal T.M.NT. Il Lower Right Side Decal T.M.N.T. ll Lower Left Side Decal

T.M.NLT. Il PO.P. Advertiser

T.M.NT. Il Manual (4P) 3 & 4 Player Harness Speaker Harness FCC Cage Kit Box

Red Joy Stick (Microswitch) Blue Joy Stick (Microswitch) Violet Joy Stick (Microswitch) Orange Joy Stick (Microswitch) Red Jump Button Red Attack Button

Biue Jump Button Blue Attack Button

Violet Jump Button Violet Attack Button

Orange Jump Button Orange Attack Button Microswitch

Palnut (Plastic)

Page 3

PUTTING YOUR BEST GAME FORWARD

PREPARATION: For best results, all old graphics should be removed completely from the cabinet. “‘Stick-on”’ graphics can be removed by using a hairdryer or hot air device. The heat from the dryer will loosen the adhesive, allowing you to easily peel them off—any adhesive residue can be cleaned off with acetone and a soft dry cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT.) TOOLS YOU NEED:

  • Foaming Aerosol (such as “Windex’’).
  • Soft Squeegee.
  • X-Acto Knife. SIDE PANEL DECALS
  • Spray area of cabinet where Side Panel decals are to be applied with foaming aerosol or a mild soap solution.
  • Remove protective backing from decals. . Position decals into place.
  • With a soft squeegee, beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish.
  • Allow to set approximately 2 to 3 hours before handling. Maximum adherence is achieved in 48 to 72 hours. fon
  • Trim side decal to fit your cabinet. CONTROL PANEL OVERLAY:
  • Drill any new holes needed,
  • Plug any holes that will not be used. (A permanent @poxy-filler works well for this step.)
  • Pre-position the Overlay prior to removing the backing.
  • Slowly apply the Overlay — inch by inch on the control Panel, removing the backing as you apply it.
  • Once it’s in place, by using an X-Acto knife, cut around the button and joystick placements. INSTRUCTION/BUTTON DECALS: Apply the Player Instruction, Button and 1 Player/2 Player decals in their respective Positions. Apply pressure fiberally. Allow to set as long as Possible before putting game on location.
NOTE: Maximum adherence is achieved in 48 to 72 hours.

MARQUEE

(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE) 1/8” Acrylic Marquee should be Cut to fit your game. DO NOT remove protective mask until this is done. One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish). CUTTING WITH A KNIFE OR SCRIBER: Acrylic sheet up to 3/16" thick may be cut by a method similar to that used for Cutting window glass. Use a scriber of some kind—a scribing knife such as the one pictured, a metal scriber, an awl, or even a sturdy craft knife —to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts Carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then clamp the acrylic sheet or hold it rigidly under a Straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.

‘Always draw the scribing knife along a straight edge. Break sheet over edge of table after scribing.

P.C.B. CAGE INSTALLATION

Konami, Inc. now supplies a new style PC.B. cage which is superior to old Style cages because of ease of installation. The cage is made of a 32 Point stem-stock which is fire retardant. TO INSTALL THE CAGE:

  • Open cage bottom and secure to desired PC.B. position.
  • Install printed circuit board inside cage using wood Screws, screwed through the cage bottom into cabinet side.
  • Close the cage over printed circuit board and secure with latch on cage.
Page 4

T.M.N 1 TECHNICAL INFORMATION

T.M.NT. Il requires horizontally mounted monitor. It also generates composite negative sync. If your monitor is composite positive sync, you will have to change to composite negative sync.

To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the output pin from the PC.B. is a combination of H-sync and V-sync.

NOTE: Please refer to Figure 2.

FIGURE 2:

FROM P.C. BOARD

NEGATIVE COMPOSITE SYNC. (PIN P on P.C.B. EDGE) (+5V and GND should be taken out of the PC. Board.)

TROUBLE SHOOTING GUIDE

OUTPUT TO MONITOR POSITIVE COMPOSITE SYNC.

PROBLEM: POSSIBLE SOLUTION

No Screen or 1). Check +5V line at the P.C.B. Adjust if necessary. Constant Reset 2). Make sure all socketed eproms and custom IC’s are seated securely. Apply light pressure to secure. 3). Check harness to be sure it is not on backwards.

No Sound 1). Check +12V line at the PC.B. 2). Make sure both speaker out wires are connected to the speakers. (DO NOT CONNECT A GROUND.)

Distorted Sound 1). Replace cabinet speaker.

VO Problem (coin 1 1). Do not hook a coin counter to the coin 1 or coin 2 outputs. This doesn’t work or Joystick will cause damage. Up doesn’t work, etc.) 2). Check your schematic for the 74LS253 IC that corresponds to your VO problem. Check the appropriate pin with a scope or multimeter for a high output (5V), if output is low replace the 74LS253.

CAUTION

DO NOT WIRE COIN COUNTERS TO THE COIN 1 OR COIN 2 OUTPUTS. THIS WILL CAUSE DAMAGE TO THE I/O MICROCHIP 74LS253. COIN COUNTERS CAN ONLY BE WIRED TO COIN COUNTER OUTPUTS.

Page 5

Se —_e- . ——_

3.0

4.0

5.0

6.0

7.0

8.0 T.M.N.T. lt MONITOR INFORMATION

SERVICE INSTRUCTIONS

NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every time the monitor is turned on after being off for a minimum of 5 minutes. Should any part of the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT face and all surrounding metal parts. Then slowly withdraw for a distance of 6 feet before turning off.

BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished). VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions. CIRCUIT PROTECTION A 400A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit. FOCUS Adjust the focus control, located on the HV unit (1352), for maximum over-all definition and fine picture detail. HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short. HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control. VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions ““U” or “D”. HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions “R” or “L”. 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning tool adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.

  • KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MONITOR.

= RED 19°—orive GRN DRIVE REO CUTOFF GRN CUTOFF’. BLU CUTOFF

*NEG H SYNC *NEG V SYNC WHEN USING COMPO: «GND. fi ee C_] ire syne use woriz. SYNC INPUTS, POS H SYNC POS V SYNC. GuD Buu GRN RED HORIZ HOLD BLK LEVEL

MORIZ VERT VERT VERT HORIZ CENTERING SIZE HOLD RASTER RASTER SHIFT = SHIFT FIGURE

Page 6

TECHNICAL INFORMATION

  • Required power capacity GND-Vcc 5V 4A or more GND-(+12V) *See the Wiring Diagram.
  • Output R (red) analog, positive G (green) analog, positive B (blue) analog, positive SYNC. H-V complexed, negative
  • The monitor should be horizontally installed.
  • Use the volume knob on the PCB to adjust sound level. Turn the knob clockwise for increased volume. In monaural output mode, use the left volume knob.
  • Handle with care.

PLAY INSTRUCTION

*1 to 4 players can play at the same time.

  • Choose the character you want to control out of the four individual Ninja Turtles: LEONARDO (Weapon: Katana), MICHAELANGELO (Nunchaku), DONATELLA (Bo staff), or Raphael (pair of sai).
  • Deposit coins into the coin slot of the character you want and press ATTACK or JUMP button to start. ¢ Control your character’s movement using the 8-way joystick and attack enemies with ATTACK button. Press ATTACK button repeatedly to slice, slash, hurl, kick, thrust the enemies. Use JUMP button to avoid enemy attack or defeat enemies in the air. Pressing JUMP button longer makes higher jump.
  • Press ATTACK and JUMP buttons simultaneously for a powerful Special Attack according to the individuality of each character.
  • Press JUMP button while in the air for a flying kick or slash.
  • Keep pressing JOYSTICK to run left or right. Press ATTACK button while running to tackle enemies or make a sliding attack.
  • Pick up a piece of pizza to fully restore your energy or to make a revolving attack.
  • Your energy will be consumed when attacked by enemies. When it is used up, you will lose one life. The game is over when you have lost all the lives.
  • There are 9 stages in all. You can continue the game as many times as you want. Any player can join at any time.

Il TECHNICAL INFORMATION

CABINET INFORMATION

  • Use a multi contro! upright cabinet with four sets of an 8-way joystick and two function buttons.
  • Four independent coin slots are necessary. Start buttons are substituted by the function buttons for each player.

8-WAY ATTACK JUMP JOYSTICK BUTTON BUTTON

Page 7

T.M.N.T. IL TECHNICAL INFORMATION (cont.)

SELF TEST

Normal: ‘‘OK”’ will be displayed. Then the game will

Abnormal: “BAD” will be displayed and self test will repeat. If “15B BAD” is displayed, switch off and switch on again with TEST SWITCH (on the PCB) pressed.

MANUAL TEST

  • HOW TO START After switching on the power, press the TEST SWITCH on the PCB or on the cabinet, and you will get the MAIN MENU of the Manual Test.
NOTE: Switching on with TEST SWITCH pressed causes the program in the EEPROM to be initialized to default.
  • HOW TO RETURN TO THE GAME MODE Select “GAME MODE” on the MAIN MENU then press player 1 ATTACK button to return to the game mode.
  • ITEMS AND HOW TO SELECT Use player 1 JOYSTICK to move arrow to desired test and press 1 ATTACK button to initiate testing. Press player 1 ATTACK button during or at the end of each test to return to the MAIN MENU.

VO CHECK SCREEN CHECK COLOR CHECK SOUND CHECK MASK ROM CHECK GAME OPTIONS COIN OPTIONS GAME MODE

1PLYR JOYSTICK = SELECT ITEM 1PLYR ATTACK=DO CHECK

  • EXPLANATION OF THE ITEMS 1.0 CHECK Check all the joysticks and buttons to see “1” when switched on. Press player 1 and 2 ATTACK buttons at the same time to return to MAIN MENU. 2, SCREEN CHECK Adjust focus, alignment, size, etc. using the crosshatch screen.
  • COLOR CHECK Adjust color brightness so that the specified area will be colorless. 4, SOUND CHECK When “SOUND SCALE CHECK” is selected, a music scale sounds. At “SOUND CODE,” push player 1 JOYSTICK right/left to change sound code.
  • MASK ROM CHECK Roms will be checked one after another, and the message ‘‘OK”’ or “BAD” will be displayed on the screen.
  • GAME OPTIONS Following screen will appear. Use player 1 JOYSTICK up/down to select the item and push JOYSTICK right/left to modify setting. Factory settings are shown in green, and modified results in ted. (Settings below are not always the factory settings.)
Page 8

T.M.N 1! TECHNICAL INFORMATION (cont.)

After modification is completed, select “SAVE AND EXIT” and press player 1 ATTACK button to save and return to MAIN MENU.

GAME OPTIONS

PLAYER'S LIFE1 CREDIT 2 LIVES..-Select from 1 to 8 lives.
DIFFICULTY LEVEL2/MEDIUM.. Select out of 4 levels.
VIDEO SCREEN FLIPNORMAL... “NORMAL” or “UPSIDE DOWN”
SOUND OUTPUTMONAURAL,. “STEREO” or “MONAURAL”

©. "ON" or “OFF” ..“GAME OVER AFTER FINAL STAGE” or “GAME LOOPS ENDLESSLY” SOUND IN ATTRACT MODE ON LOOP SETTING GAME LOOPS ENDLESSLY

FACTORY SETTINGS SAVE AND EXIT EXIT ...All the settings return to default. . Save the modified settings.

1PLYR JOYSTICK UP/DOWN=SELECT OPTION 4PLYR JOYSTICK RIGHT/LEFT=MODIFY SETTING

*If you select “EXIT” instead of “SAVE AND EXIT” after modifying some settings, the message appears: “YOU DID NOT SAVE. DO YOU WANT TO SAVE? YES/NO.’ When you choose “YES,” the screen shows “NOW SAVING” and returns to MAIN MENU. If you select ‘‘NO,” “NO MODIFICATION” is shown and then MAIN MENU appears.

  • COIN OPTIONS Selecting this item, the screen shows following options.

COIN OPTIONS

PREMIUM STARTYES 1.. “NO” or “YES 1” to “YES 3”

(The number means the EXTRA coins necessary) STARTING 2 COINS 1 CREDIT

CONTINUATION 1 COIN 1 CREDIT

FACTORY SETTINGS SAVE AND EXIT \ Same as above “GAME OPTIONS” EXIT

1PLYR JOYSTICK UP/DOWN=SELECT OPTION 4PLYR JOYSTICK RIGHT/LEFT=MODIFY SETTING

When you want “PREMIUM START” setting, choose the number of extra coins necessary for starting, then decide the coin setting for continuation. The number of coins for starting will be the sum of both numbers. If you do not want premium start setting, the number of coins necessary for starting and continuation will be the same. *COIN SETTING OPTIONS

Page 9

T.M.N.T. Il SUB HARNESS FOR 3 PLAYERS & 4 PLAYERS SS

1 | Coin 3 Blue/White 2 | Empty 3 | 3P Left White/Red 4 | 3P Right White/Yellow 5 | 3P Up White/Black 6 | 3P Down White/Blue

CN37 | 3P JumpWhite/Brown
3P8 | 3P AttackWhite/Orange

CONTROLS 9 | Empty 10 | Empty 11 | Empty 12 | Empty 13 | Empty 14 | Empty 15 | Ground Black

1 | Coin 4 Red/Green 2 | Empty 3 | 4P Left Yellow/Black 4| 4P Right Brown/Black 5 |} 4P Up Green/Yellow _ 6 | 4P Down Yellow/Red

CN47 | 4P JumpYellow/White
4P8 | 4P AttackYellow/Blue

CONTROLS 9 | Empty 10 | Empty 11 | Empty 12 | Empty 13 | Empty 14 | Empty 15 | Ground Black

Page 10

T.M.N.T. I] WIRING HARNESS

*JAMMA HARNESS NOT SUPPLIED

Solder Side rn Parts Side

GND GND

GND GND

+5V DC +5V DC

+5V DC +5V DC

NOT USED NOT USED

+12 DC +12V DC *xey| H | 7 | “KEY cempty)| J | 8 | COIN COUNTER (empty) | kK | 9_| (EMPTY) SPEAKER (-)| L | 10 | SPEAKER (+) (empty) | mM | 11_| (EMPTY) VIDEO GREEN | N | 12 | VIDEO RED VIDEO sync |_P VIDEO BLUE

(EMPTY) VIDEO GROUND

(EMPTY) TEST SWITCH

COIN 2 COIN 1

NOT USED NOT USED

2P UP 1P UP

2P DOWN 1P DOWN

2P LEFT 4P LEFT

2P RIGHT 1P RIGHT

2P ATTACK 4P ATTACK 2p sump | a | 23 | 1P JUMP Not UsED| b | 24 | NOT USED NOT USED NOT USED

NOT USED NOT USED

GND GND

GND GND

(BASE COLOR/LINE COLOR)

Page 11

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 12

CONTROL PANEL DRILLING TEMPLATE

Use this Template for All 4 Players Controls

Player 1 Blue Player 2 Orange Player 3 Purple e @ Player 4 Red

MOILSAOr

dwar

MOVLLY

Page 13

HOW TO. PLAY

CONTROL n= ¢ F: ‘SS

  • Each Turtle has a —. attack method. ‘ Press JUMP & ATTACK buttons at the same time for SPECIAL ATTACK !
  • Press JUMP button longer to jump higher.
  • Press ATTACK button while jumping for a flying kick or weapon attack.
  • Press ATTACK button while running to tackle enemies or make sliding attack.
  • Pick up pizza for more energy or to make a Tevolving attack.
  • Hit button and wiggle the joystick to escape when caught by enemies.

INSERT MORE coms TO CONTINUE | THIS EQUIPMENT COMPLIES ‘ WITH THE REQUIREMENTS IN PART15OFFCCRULESFORA CLASS A COMPUTING DEVICE. | OPERATION OF THIS EQUIPMENT INA RESIDENTIAL AREA MAY CAUSE | UNACCEPTABLE INTERFERENCE TO RADIO & TV RECEPTION REQUIRING THE OPERATOR TO TAKE WHATEVER | STEPS NECESSARY TO CORRECT THE INTERFERENCE. ; # 063101

ov a a

ATTACK

« Each Turtle has a different attack method. ‘¢ Press JUMP & ATTACK buttons at the same time for SPECIAL ATTACK !

  • Press JUMP button tonger to jump higher.
  • Press ATTACK button while jumping for a flying kick or weapon attack. ‘« Press ATTACK button while running to tackle enemies or make sliding attack
  • Pick up pizza for more energy or to make a revolving attack.
  • Hit button, and wiggle the joystick to escape when caught by enemies.

INSERT MORE COINS TO CONTINUE !

Page 14

WVYDVIC DNIMIM

PROPRIETARY AND CONFI

Reproduction forbidden without the . spesilfe written permission of Konami Co, fers or transfers any right ino use the printog ctuit boards this drawing of ether subject matter of the .srawing of any desigr’or technical infr-

‘mation shown thereon. Except

Lig, and for maniutacture under Konam’s,

write license, No sight is granted 10

4] reproduce, make, have made, use or sell

-] this crawing or the subject mater there-

  • without limitation, the print Konami Co., Lid, All rights. reserved. CONTROL FOR 1P°

CONTROL FOR 2P

CONTROL FOR 3P CONTROL FOR 4P NOT APPLICABLE 28 1A G12V REQUIRED POWER CAPACITY | STEREO |

7 808y 7 _8o8¥ LEFT ‘SPEAKER(+) SPEAKER(-) SPEAKER(-) ‘SPEAKER( +)

GNO

  • U RIGHT POWER +5v suppLy He

+12V

tranulactufety vendors of Konami Co. |-" P

  • _ TEST goBy gosv peasy TEST fp.cone Toe PARTS SLOE SOLDER SIDR

i I ‘OND ov +8V +v +8v +120 +12V

  • COIN COUNTER2 J wow LP —-

‘COLOR MONITOR COINT SERVICE! _

ot

slo

t TP=ATTACK

= TP= JUMP COIN2 SERVICE2 lod |t & o— los | 1 a

rs O SERVICES ah COUNTER COIN COUNTER SPEAKER( +) SPEAKER(-) RED 1P-RIGHT J2P-RIGHT IP-ATTACK J2P-ATTACK 1P-JUMP. [2P- JUMP SERVICE2

oat |

He) |, a | ral it L_ 3P-LEFT. 3P=RICHT j

[Ff \} O 3P= JUMP

= ARARPAR i BI

SERVICE4 ' [ [COINS SP-LEFT }3P-REGHT 3P-UP /3P-DOWN /3P-ATTACK 3P- JUMP SERVICES GNO (GND. [ele | T ill

a

| E (aP=-RIGHT [4P=uP 4P-DOWN iif

4P-ATTACK 4P—JUMP

IO! 7c i

  • NOTE —
  • 1P:NO. 1 PLAYER 2P:NO. 2 PLAYER, 3P:NO, 3 PLAYER 4P:NO. 4 PLAYER
  • SURGE KILLER DIODES FOR COIN COUNTER INSTALLED ON THE PC.B.
  • YOU CANNOT USE BOTH STEREO AND MONAURAL OUTPUTS AT THE SAME TIME. COING AP-LEFT }4P-RIGHT |aP-uP |4P-DOWN |4P-ATTACK 4P-JUMP SERVICES }GNO [GND SPEAKER QUTPUT 4P NH CONNECTOR B4P-SHF-1AA J.S.T. Na JAMMA SEPIN EDGE CONNECTOR 8/32 INCH PITCH GX063 PWB 352359C

EXTENSION 1/0 15P NH CONNECTOR BISP-SHF~1AA cna. EXTENSION 1/0 15P NH CONNECTOR BISP-SHF-1AA Na

TIystyy

a,

Page 15

are Dea Uli U1__68000 -16mHz

wove 2bewo ut Gi

Bie OBe aie CSISRES. cose QUOTACK osc OBS. taoe BGA esac ak yas.

oss DAEE 570 (>QE2___________________}_18 72 e570 OM Feunre

uio 1 2 a, D2 —-yres cunre oP qi alee B.1Mesch FZ geeseee

care DR, leu t— i T cunrs 2 buys cunts le Ro be : Sipma O08 otc COUNT? Moss5 fo COUNT gg DESIGN K. FURUKAWA TITLE

SCHEMATIC SUBTITLE

DRAW K. FURUKAWA

CHECK

beri

PAGE

APPROVE

CODE NO. 352995

POAT

SCALE

i Aine REG. TYPE Gx063

KONAMI CO..LTD. TOLERANCE SECURITY LEVEL CONFIDENTIAL

DATE 1991/09/18 °

Page 16

so 7 oes > — iste 0?

WELK ces cosy DML cae CoStSRES ro aR BEEECGoue

o1ek DME ura. 23

By a SR1I6KSL4 BLUE este

essen GREEN opie

czoe DOL o2ec 280! caac DSO SSRSe DD os1 INC osiF DRAWING DESIGN K. FURUKAWA TITLE SCHEMATIC.

PROPRIETARY ANO CONFIDENTIAL: ]

FEPRODUCTION FORGIOOEW WITHOUT THE SPECIFIC WRITTEN PERMTSSION OF KONAMI CO.-LYD. 7-3-2, eM OTKU, KOBE 860. JAPAN. THIS ORAVING 1S ONLY Ct DRAW K. FURUKAWA ‘SUBTITLE 04

‘OF THIS ORAVING OR ANY OPERATING MANUAL RELATING T( ‘A

eee eS RRVING CONFERS. OR TRANSFERS. ANY RIGHT IN OR LICENSE TO USE THE PRINTED CIRCUIT ansses CHECK qekina. PAGE

RT MATIER OF THE. ORAVING @8 ANY OESIGN OR TECHNICAL TNFOnHATICN

i oe Ot chien se APPROVE Rlom- CODE NO. || 352995

BES THEREON EXCEPY FOR MANUEACTURE BY VENOCRS CF KONAMI CO..LTD. ANO FOR MANUFACTURE UNDER SCALE, REG, TYPE GX063

SAO THEREON. EXCEPT FOR WAMEACTURE Bh EMCO CEpmaMuce. DUNE. AVE MAGE. USE Gk SELL HS 0 Fe Eee ee aN aie aGReEveNT WITH OR ARITTEN PERPLOSION PROM RELSME “0, K@NAMI C@..LTD. TOLERANCE secontty vevet || CONE LDENTIAL

Hea eee er tatTER THEREOC INCLUDING. WITHOUT LIMITATIN. THE PRINTED CIRCUIT BOARD OR 3

COPYRIGHT 199! KONAMI C8..LTD. ALL RIGHTS RESERVED. DATE 1991/09/18 T 2 T 3 T a T z 1 a : = : =

Page 17

fa

Ch vm ALSO4 SIN 06. Ter

$22 EVQ-QS5-07K 1 3 LS oat aa a0 _lao segtset oss appa

S TT vec. GND 1, 86 05273 ine va ns ¥3| ke v2 Inti Ive GNO

ypLert ([20} spatcu [27] 1psHaeT! spseor2 23} ypsHeeT3 24} Saaasey 1PSHOOTZ pose [22SHOOTZ pose 1PSHOOTS FP nese BPSHODTS Fosse

cOINa eB =~ err Cala FRc = C3 cir Shen

3PLEFT PRIGHT 88] ona B15P-SHF-1AA

3PuP focal) [18 2CBNK2_- 9399 88. [16 ecankt 5 9388 cN4 [13 —DCBNKO = ose0 B15P-SHF-1AA

seoow [3h oom (Shaw

seskoot), 7} apor! Thee

sesroore 3} aoe CBhaye

aeshoers C3} COIN, tor COIN roo ho

Saar Syes] i Sats CFeity OFF14

‘PSTART bi

SERVICES ry ls i cose D-REREK. jax Rafe “to0 cto | 7 xo | 38 88] ont

JAMMA

ee)

Oo al ~ PROPRIETARY AND CONFIDENTIAL: } = = We K. FURUKAWA SUBTITLE 05

Lb ORAM | fe =

af

SEPRODICTION FORBIOOEN WITHOUT THE SBECIFIC WATT aFagine

APPROVE Los CODE NO. 352995

WA-NAKAMACHT. CHUC-KU. KOBE 650. JAPAN.

SCALE. REG, TYPE GX063

2 THIS ORAVING. OF” ANT 0° | CO..LTD. TOLERANCE security tevee |] CONFIDENTIAL ps DRAWING DESIGN K. FURUKAWA TITLE. SCHEMATIC

i I i i KONAMT DATE 1991/09/18 1 T ? i 3 ” 4 T R T G T 7 T a

Page 18

PROPRIETARY AND CONFIDENTIAL :

THE SPECIFIC WRITTEN PERMISSION OF KONAMI CO. LTO. .7-3-2.

KOBE 650. JAPAN. THIS ORAVING IS ONLY CONDITIONALLY ISSUED. NEITHER

(ANURL, RELATING TO KCNAMT'S GAMES OR PRODUCTS:

BR LICENSE TO-USE THE PRINTED CIRCUIT BOARDS

RELATING THERE TSOEVER. UNLESS 8Y WRIT COPYRIGHT 1991 KONAMI CO, LTD. ALL RIGHTS RESERVED Lp KORA UD KONAMI CO.,LTD. DRAWING

DESIGN

K.FURUKAWA TITLE,

SCHEMATIC SUBTITLE

ORAW K. FURUKAWA

07,

CHECK

ane PAGE

APPROVE Bran E-Lino. CODE NO. 352995

SCALE REG. TYPE GX063

TOLERANCE SECURITY LEVEL CONFIDENTIAL

DATE 1991/09/18

Py T Ey a a T °

Page 19

0588. U59 MS8M16. OH

cnc) asfestceitasddalelsts 52885 Ree

0808 O.1M25CA X22 330M16E X2

PROPRIETARY ANO CONFIDENTIAL:

REPRODUCTION FORBIDUEN WITHOUT THE SPECIFIC WRITTEN PERMISSION OF KONAAI CO. LTD. .

HINATOOTHA-NAKAMACHI. CHUO-KU. KOBE 650. JAPAN. THIS ORAVING IS CMLY CONDITIONAL

NOR POSSESSION CF THIS DRAVING OR ANY OPERATING MANUAL RELATING TO KONAD

NG THIS ORAVING CONFERS OR TRANSFERS ANY RIGHT IN OR LICENSE TO USE THE PRINTED CIRCULT BOARDS To THIS DRAWING OF OTHER SUBJECT MATTER OF THE DRAWING OR ANY DESIGN GR TECHNICAL INFORMATION SHOWN THEREON. EXCEPT FOR MENUFACTURE BY VENOORS OF KONAMI CO..LTD. AND FOR MANUFACTURE UNDER RONAMT'S VALTIEN LICENSE, NO RIGHT [S GRANTED TC REPRODUCE. MIXE. HAVE MADE. USE OR SELL THIS ORAVING OR THE SUBJECT HATIER THEREOF INCLUDING. VITHOUT LIMITATION. THE PRINTED CIRCUIT BOARD OR OPERATING MANUAL PELATING THERETO. WHATSOEVER. UNLESS QY WRITTEN AGREEMENT VITH OR WRITTEN PERMISSION FROM KONAMI

COPYRIGHT 1931 KONA CO, .LTD. ALL RIGHTS RESERVED. Lb IORUAIAM KONAMI CO.,LTD.

ORAWING

DESIGN K. FURUKAWA

TITLE

SCHEMATIC

ORAW K. FURUKAWA SUBTITLE

CHECK TIA, PAGE

APPROVE Linh CODE NO. 352995

SCALE REG. TYPE GX063

TOLERANCE SECURITY LEVEL CONFIDENTIAL

OATE 1991/09/18

2 1 3 T 4 T ] 7

Page 20

THIS EQUIPMENT COMPLIES WITH THE REQUIREMENTS IN PART 15 OF FCC RULES FOR A CLASS A COMPUTING DEVICE. OPERATION OF THIS EQUIP- MENT IN A RESIDENTIAL AREA MAY CAUSE UNACCEPTABLE INTERFERENCE TO RADIO AND TV RECEPTION REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

a” ~ KONAMI"

900 Deerfield Parkway, Buffalo Grove, 60089-4510 Telephone: (708) 215-5100, Telex: 6871385 KONAM UW, Fax: (708) 215-5122