CATHODE RAY TOMES

xStation Installation Guide (PU-18)

PlayStation (Sony, 1994) · Installation Guide · 11 pages · 1 sections · original scan

Page 1

» <Station

© installationGuide ©

PU-18

Page 2

xStation ODE installation guide for the PU-18 Playstation 1 motherboard

PU-18 Mainboards can be found in: All SCPH-5001 All SCPH-5501 — 5503 All SCPH-5552 (very rarely) SCPH-7001 — 7003

  • You have to disassemble the Playstation 1 completely to get to the mainboard. PLEASE REMOVE ALL CABLES FROM THE POWER SUPPLY. MAKE SURE THAT THE POWER CORD IS DISCONNECTED!
  • Search for IC701
  • 1C701 is labeled CXD2545Q. You will find it in the lower right corner. See picture below

Guide by: Dev: Production and Sales i ._ www.castlemaniagames.com +s seewood

Page 3
  • From IC701 (CXD2545Q) you have to lift the following pins: 45, 46, 47, 56, 74, 77,78 and 80. Please make sure that only the shown pins are lifted 1C: 666: :

80 78 77 74 35 Lift Pins / Pins anheben 48

  • Please be careful not to damage the mainboard when lifting pins. Use a needle or x-acto knife and a fine soldering tip to simply touch the pin and apply some heat, then gently lift it from underneath using the needle or blade. (In the picture | have turned the mainboard to get easier access to the pins

Dev: Production and Sales SG Guide by: rama ._ www.castlemaniagames.com < seewood

Page 4
  • Please make sure that you have lifted the pins completely. They should have no contact with the motherboard =“ (20z51
  • We are now finished with the top of the mainboard; turn it bottom side up. Now you have to solder the Quick Solder Board (QSB). Focus on the area marked below.

Dev: Production and Sales SG Guide by: rama ._ www.castlemaniagames.com < seewood

Page 5
  • The positioning is kept very simple and can already be seen at the solder pads of the QSB. Simply place the QSB on the mainboard as shown, the yellow markings make it clear again. if y 5

X-Station °°» S50X QSB vi

  • Before soldering, the via pads on the left and on the right (yellow circle marked in the picture above) need to be lightly scratched.

Left Side Right Side

Guide by: Production and Sales “ ._ Www.castlemaniagames.com oye seewood

Page 6

After preparing it should look like this:

  • on the left

Before

  • on the right:

Before After applying some solder

  • Now you have to desolder/remove one small resistor, which is located next to the OSC V67.737 KDS813 in the purple box.

Puree cy te 3

Guide by: © seewood

Page 7
  • The small resistor (marked in violet) has to be removed.

>

re] o.

Q

x Ci

o

resistor was here

Dev: Production and Sales ee Guide by; rama www.castlemaniagames.com “ois seewood

Page 8
  • The difficult part is now finished, but the lower part of the PS1 case still needs to be prepared. Cut off the small plastic pin marked below in red. This is necessary to prevent the flex cable from breaking during installation.
  • Now you have to connect the flex cable to the cable holder on the QSB. (blue side up) and close the cable holder. When this is done you can lead the flex cable outside X-Station 550X QSB vi

Production and Sales Guide by: ._ Www.castlemaniagames.com Sis seewood

Page 9
  • To ensure that the cable sits correctly route it through the slot on the top shield.
  • Prepare the PCB and push all 3 spacers into the xStation board. If you look at it from above they can be found in:
  • the lower right corner
  • the upper right corner
  • the upper left corner.

Production and Sales Si Guide by: . Www.castlemaniagames.com ( phe seewood

Page 10
  • Now grab the other side from the flex cable and carefully connect it to the cable holder on the xStation. When it is done you have to fold the flexcable a bit. Folding it like this is best:
  • Mount the xStation on the posts of the original Disc Drive. It should look like this:

Dev: Production and Sales i < Guide by: fama . WWw.castlemaniagames.com ‘Sys, seewood

Page 11

When everything is ready, you have to reassemble the Playstation 1 in reverse order.

A freshly installed xStation:

recommended adaptation of PCB and SD card adapter

  • You can use the rubber spacer to clamp 2. Use a 3D printed mount to the xStation in place. fill the drive gap.

Dev: Production and Sales i < Guide by: fama . Www.castlemaniagames.com “9s seewood