CATHODE RAY TOMES

Guardians of the Hood TM-375 1st Printing

Guardians of the 'Hood (Atari Games, 1992) · Technical Manual · 64 pages · 54 sections · original scan

Page 1

Ast printing -

QPERATOR’S

MANUAL

Page 2

7 ‘This cover was printed on recycled paper ‘made from 100% post-consumer waste that thas not been de-inked.

Page 3

erator’s Manual — with Schematics A

ATARI

GAMES

Page 4

INTRODUCTION @ GUARDIANS OF THE HOOD

Copyright © 1992 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, ‘without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95036 Printed in the U.S.A. 2/92 Produced by the Atari Games Technical Publications Department. Writing & Editing: Andrea Dencker Illustration & Design: Mary Ohanessian Sumner

ia NoTIceE RE.

NoOoN-ATARI

PARTS

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

GUARDIANS OF THE "HOOD % INTRODUCTION

SAFETY

SUMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. ‘ Use Only Atari Parts. To maintain the safery of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions. ‘WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

tit

Page 6

INTRODUCTION 4 GUARDIANS OF THE "HOOD

1 Set-Up How to Use This Manual Operating the Game Inspecting the Gam« Control and Switch Locations Installing the Control Panel... Setting the Coin and Game Options. Game Play

2 Self-Test

Entering and Exiting the Self-Test. RAM and ROM Test Select Test Menu .. Switch Test... Volume Adjust. Sound Test ... Coin Options. Game Options.. Game Statistics Alphanumeric Test .. Motion Object Test. Playfield Test Color Test... Convergence Test

iv 3 Troubleshooting and Maintenance

Maintaining the Coin Mechanism... Repairing the Video Display .. Repairing and Replacing the Joystick Contro! ROMs and RAMS .......seccecsceseeseeessetecseeeeesies

4 Parts Illustrations

Part Ordering Information 4-1 For figure and page numbers, see the List “Of Mlustrations that follows.

5 Schematics

See the List of Illustrations that follows.

Statistics Sheet

After the end of Chapter 5

Warranty Inside back cover praurii

Page 7

GUARDIANS OF THE "HOOD * INTRODUCTION

ILL

Figure 1-1

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12

Figure 3-1

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4

Figure 4-5 Figure 4-6

Figure 4-7

Figure 5-1

Figure 5-2

Figure 5-3

Figure 5-4

Figure 5-5 Figure 5-6

Figure 5-7 TRATION

Self-Test Switch Locations

Select Test Menu Screen.. Switch Test Screen. Volume Adjust Screen. Sound Test Screen... Coin Options Screen Game Options Screen Statistics Screen... Alphanumeric Test Screen Motion Object Test Screen Playfield Test Screen. Color Test Screen. Convergence Test Screes

Maintaining the Joystick Assembly..... 3-5

Cabinet-Mounted Assemblies Control Panel Assembly... Joystick Assembly... Coin Controls, Inc. Coin Door Assembly ... Power Supply Assembly... Guardians of the "Hood Game PCB Assembly ... JSA Audio III PCB Assembly.

Guardians of the "Hood Game PCB Assembly Schematic Diagram Hitron 5V, 7A Switching Power Supply Schematic Diagram... . Peter Chou Power Supply Schematic Diagram (optional) " JSA Audio III PCB Assembly Schematic Diagram Game Main Wiring Diagram... Over/Under Coin Door Wiring Table 1-1

Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5

Table 3-1 Table 3-2

Table 3-3 Table 3-4 Game Specifications

Summary of All Self-Test Screens .... Bad RAM Location by Error Addres: Bad ROM Location by Error Address. Coin Option Settings .. Game Option Settings

Troubleshooting Table... Voltage Inputs and Test Points on the PCBs..... What ROM Problems Look Like. Screen Colors Indicating Bad RAMs

Page 8

INTRODUCTION * GUARDIANS OF THE 'HOOD

Page 9

CHAPTER 1

Set-Up

How to Use This Manual

t, HIS MANUAL IS written for

operators and service person- S Mm nel. It provides information for setting up, playing, testing, and maintaining your Guardians of the *Hood™ (neighborhood) game. Guardians of the "Hood is a oneor two-player fighting game with two sets of controls and 3-D digitized video, The game provides photographically real views of a seedy inner city. ¥ Chapter 1 contains set-up and game play information. vx Chapter 2 contains a description of the self-test procedures. The self-test is important in the Guardians of the "Hood game. You can trouble-

shoot the PC boards, main circuits, and controls using the more than 11 screens in the self-test. You should regularly test the boards and controls with the selftest to keep your game in peak condition and at top earnings. x Chapter 3 contains several troubleshooting tables, plus maintenance and repair procedures for the coin mechanism, video display, joystick, ROMs and RAMs. If you have problems with your game, use this chapter to troubleshoot and to repair it. Be sure to perform the preventive maintenance tasks to keep your game in good condition. % Chapter 4 contains the illustrations and PCB parts lists. vx Chapter 5 contains the schematics for the game and audio PCBs and the game wiring diagram.

Page 10

CHAPTER 1 ~ Set-Up % GUARDIANS OF THE "HOOD

Operating the Game

To operate your game for maximum income, you should regularly do the automated self-test and check the controls with the Contro/ Inputs screen in the selftest. By using the self-test regularly, you can find and fix problems immediately. This lets you keep your game in top condition.

Inspecting the Game

WARNING To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded. Inspect your Guardians of the "Hood game carefully to ensure that the game is complete and was delivered to you in good condition. Inspect the cabinet and seat as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Open the upper and lower rear access panels. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed So they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are in- 4 Characteristic Power Consumption — 150 W maximum Line Fuse Rating 3 Amps Line Voltage 102 to 132 VAC Temperature 5° to 38° C (37° to 100° F) Humidity Not to exceed 95% relative Width 33.25 inches (84 cm) Depth 38.25 inches (97 cm) Height 71.75 inches (182 cm) Weight 325 Ibs, (148 kg)

Table 1-1 Game Specifications

stalled. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wifes are connected. e. Inspect other sub-assemblies, such as the video display, controls, printed-circuit boards (PCBs), and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Control and Switch Locations

All of the controls are located inside the drawer or behind the coin doors (see Figure 1-1). The following describes the locations in more detail:

Power On/Off Switch

The power on/off switch is located at the upper rear panel of the cabinet, above the rear door. Volume Control

There is no volume adjustment knob on this game’s PCB, Instead, volume is adjusted in the self-test. Refer to Chapter 2 of this manual for more information.

Page 11

GUARDIANS OF THE HOOD “ CwapTER 1 — Set-UP

Secondary Self-Test (2-pin header labeled “STEST”). Must be jumpered together to activate the self-test mode.

Primary Self-Test Switch

Figure 1-1 Self-Test Switch Locations

Self-Test Switch

The primary self-test switch is conveniently located inside the upper coin door (inside the left edge of the Opening).

Coin Counter

The coin counter is located on the bottom right edge of the coin box, inside the lower coin door.

Installing the Control Panel

Make sure the game power is turned off. To install the separately packaged control panel, you need the following tools:

  • Hex driver or wrench
  • Four flat washers (provided with game)
  • Four nut/washer assemblies (provided with game)
  • Reach in through the openings on the front of the drawer, and open the spring draw latch on each side. Pull the drawer out partly (see Figure 1-1).
  • Hold the contol panel up to the front of the drawer, and match up the four threaded studs with the four small holes (one in each comer). 3, Install one flat washer and nut/washer assembly onto each threaded stud.
  • Plug the two control panel harness connectors into the game harness inside the drawer. These connectors are keyed, so you should be able to determine which ones connect together.
  • Close the drawer and snap shut both latches.
  • Tum on the game power. Check that the video display and the attraction lamp have power.

Setting the Coin and Game Options

The Guardians of the ‘Hood coin and game options are set in the self-test. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This section describes the features and play of the Guardians of the "Hood game.

Page 12

Carter 1 -- Set-Up “ GUarbiaNs oF THE "Hoop.

Introduction

The place is Center City. An escalating crime rate has converted a once-peaceful town into a seedy hangout for gangs and hoodlums. Three gangs have taken over the town — the Dreads, the Shavers, and the Dragons. Each gang has an evil boss that rules over them. The plan for the Guardians of the ’Hood is to break up the gangs and convert the bosses to their side. Only this way can they turn the tide and regain the city. In the end, the secretive “Mr.. Big” unveils his true identity, that will surely surprise every player. The local gym has become a meeting spot for a band of young citizens called the Guardians of the "Hood. Here they work out and train with each other to keep their fighting skills razor sharp and instincts cat-like keen. Each could be registered as a lethal weapon, and united their fires burn hotter than boiling lava and pump up to the strength of one hundred men.

Game Characters

The characters in Guardians of the "Hood are:

  • CONNER — An all-around good fighter. Trained in both boxing and Karate, he possesses amazing quickness for his size. Graduating with honors from Center City University in medicine, he is considered the most eligible bachelor of the town.
  • CHIEF — Tough as a truck and the size of three men. After losing his family in a batle between two rival gangs, he pledged to bring back peace to the city. He is so devoted to the cause, that he passed up a multi-million-dollar football offer.
  • TANYA — She is the tall statuesque cat. When not securing the peace in Center City, she can be found adorning the covers of major fashion magazines. Her father’s duty in Special Forces influenced her interest in the martial arts. She possesses black belis in Tai-Chi, Tae Kwon Do, and Kung Fu. « JAVIER — He is a gold-medal winner in kickboxing. His natural speed and agility aided his ability to be a multi-sport athlete. After the Guardians of the ‘Hood clean up the city, he plans to return to his shortstop position on the Center City Bashers.

Game Play

Guardians of the "Hood is a two-player game full of hard-hitting action. Players wage the war against crime with four powerful fighters. As players punish rival gang bosses and convert them to their side, the selection of player characters increases. There’s seven in all! From closed-in Gym Waves to wide-open street scenes, Guardians of the "Hood gives players the best of both worlds ... head-to-head and side-scrolling game play. Meet head-on with gangs who make bad streets, back alleys, and subway stations their domain to prey on the weak! Players can even pick up and use street junk like garbage cans, parking meters, newspaper stands, and even car fenders! The unique five-button/joystick control arms each fighter with many devastating fighting moves. There are lots of hidden moves for players to discover! The new power-perfect 3-D digitized graphics make the action almost too close for comfort! But you be the judge of that! Don’t turn your back on those that need you ... help save the city! Who knows, hero, you may see yourself on the front page!

Page 13

CHAPTER

Self-Test

Introduction

‘ f; SE THE Guardians of the "Hood self-test when you first set up the game,

: ; self-test to check the condition each time you collect the money, or eA, . of the game circuitry and con- when you suspect game problems. This

trols. You will see the self-test information chapter shows the screens in the self-test

on the video display and hear the sound and explains each of the tests. The screens test information through the speakers. You and explanations are arranged in the order do not need any additional equipment they appear in the self-test. Table 2-1 lists

to perform the self-test. Perform the all the self-test screens.

Page 14

Cuapter 2 — Ser-Test “ GUARDIANS OF THE "HOOD

Entering and Exiting the Self-Test

This game has two self-test switches. The primary one is conveniently located inside the upper coin door (inside the left edge of the opening). The secondary selftest switch is located on the JSA Audio III PCB, in the drawer behind the control panel. To enter the self-test, turn on the self-test switch inside the upper coin door. Doing so displays the Select Test menu (entitled “Self Test”); see Figure 2-1. Exit the self-test by turning off the self-test switch at any time.

RAM and ROM Test

When you turn on the power, the game automatically runs through the random-access memory (RAM) and read-only memory (ROM) test. This test is not part of the self-test procedure. Regardless of whether or not the game has a problem, it will always advance to the attract mode. The game will stop only if you power it

Self Test (Select Test Menu)

‘Switch Test

Volume Adjust Sound Test

Coin Options Game Options Game Statistics

Alpha(numeric) Test Motion Object Test Playfield Test Color Test First Color Test Second Color Test Red Color Purity Green Color Purity Blue Color Purity White Color Purity Grey Color Purity Convergence Test White Convergence Violet Convergence Blue Convergence Yellow Convergence

Table 2-1 Summary of All Self-Test Screens

2-2 up and the self-test switch has been previously turned. on,

Game RAM Test

No message appears while the test is checking the RAMs. If more than 30 seconds elapse and the self-test menu doesn’t appear, the game has a problem. See Table 2-2 for the locations of bad RAMs. If the test finds no RAM errors, no message appears and the program goes to the ROM test after 15-20 seconds.

Game ROM Test

If the test finds no ROM errors, no message appears and the program goes to the title screen in the attract mode. If a ROM fails, a message is displayed. Furthermore, if the failed ROM is a program ROM, then the error number with checksums is shown in the center of the screen. The ROM error test takes a few seconds. See Table 2-3 for the location of bad ROMs. If you think you have a ROM error, but the screen shows no messages, see Table 3-3 for information about the locations of various ROM functions. Depending on how bad the ROM error is, you may not be able to enter the self-test.

Select Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the menu using any joystick. Start the selected test by pressing any Defend button.

RAM Location

Error AddressHighLow
FE8000 (Color RAM)3C2c
FFO000 (Video RAM)17N15N

Table 2-2: Bad RAM Location by Error Address

ROM Location

Error AddressHighLow
0000008D8c
0200009D9c

Table 2-3 Bad ROM Location by Error Address

Page 15

GUARDIANS OF THE 'HOoD “ Cuaprer 2 — SELF-TEST

SWITCH TEST

DEF=DO TEST senescent pomamemmna

Figure 2-1 Select Test Menu Screen

Switch Test

The switch test screen for a two-player game is shown in Figure 2-2. Test the joysticks and pushbutton switches. As you use each control, the pink Xs for the pushbuttons change to 0s, or the joystick switch markers (small yellow dots) are highlighted. If the changes do not appear on the screen, check the switch wiring and the switches.

NOTE The coin mechanisms are checked in the Sound test. See the section that follows.

Press the Punch and Kick buttons simultaneously to return to the select test menu.

ea a I SS SS TTT TE SWITCH TEST ji ADDRESS DATA ' £00000 i £00002 ‘ £00010 £00012 LABEL SWITCHO SWITCH1 STATUS 0 STATUS 1

00000000 00000000 i DEPRESS PUNCH & KICK TO EXIT i [_Dernss PuNcHts zm a

Figure 2-2 Switch Test Screen

Volume Adjust

Adjust the volume of the game using this screen, shown in Figure 2-3. Follow the instructions at the bottom of the screen to change the volume, to restore the old volume level, and to save the new volume and return to the select test menu.

E e

USE JOYSTICK TO CHANGE VOLUME PUSH KICK TO RESTORE OLD VOLUME | PUSH DEF TO SET NEW VOLUME AND EXIT Somes TEST

Figure 2-3 Volume Adjust Screen

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-4. : Use one of the joysticks to select from the sounds; press one of the Punch buttons to listen to it. (You can have numerous sounds playing simultaneously, or you

pepe sm RSE ET SOUND TEST casera

4 MUSIC CHIP TEST

NUMBER OF SOUNDS : 158 SOUND CPU STATUS : GOOD PUNCH=PLAY. KICK=STOP DEF=EXIT

COIN MECH SWITCHES: LEFT Load

° RTL ro

Figure 2-4 Sound Test Screen

Page 16

(CHAPTER 2 — SELF-TEST “ GUARDIANS OF THE "HOOD

Option ble Settings Explanation

Free PlayNow YesLets you choose free play to demonstrate the game.

Discount to Continue Now Yes If set to Yes, this option reduces by 50% the player's cost to continue a game (always rounded up to the next full coin).

Game Cost1 coin 1 creditvThe number of coins required for one credit.

2coins 1 credit

8 coins 1 credit

Bonus for Quantity None v Lets you choose from various kinds of bonuses or no bonus. Buy-in 2 coins give 1 3 coins give 1 3 coins give 2 4 coins give 1 9 coins give 2 9 coins give 3

Right Mech Value1 coin counts as 1 coinwThe number of coins each coin counts as in the right coin

1 coin counts as 2 coins mechanism,

1 coin counts as 7 coins 1 coin counts as 8 coins

Left Mech Value1 coin counts as 1 coin”The number of coins each coin counts as in the left coin

1 coin counts as 2 coins mechanism.

1 coin counts as 7 coins 1 coin counts as 8 coins

v Manufacturer's recommended settings

Table 2-4 Coin Option Settings

can have silence, depending on which ones you select.) Pressing any Defend button returns you to the select test menu. COIN OPTIONS

Free Play:

Coin Opti

oin Options Discount to continue:

Check and select the coin options on this screen, i Game cost: shown in Figure 2-5. The screen shows the factory de- i fault settings in green. Bonus for quantity buy-in: To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The i Left Mech Value: coin option settings, with defaults, are shown and ex- " plained in Table 2-4. Right Mech Value:

UP-DOWN SELECTS OPTION RIGHT-LEFT MODIFIES OPTION KICK RESTORES FACTORY SETTINGS START TO SAVE & EXIT

Figure 2-5 Coin Options Screen

Page 17

GUARDIANS OF THE "HOOD @ CHAPTER 2 — SELF-TEST

Option Available Settings

Difficulty Level Scale of 1 to8 (where 1 = Easy and 8 = Hard) Sv Explana

Sets the game difficulty.

Music in Attract (Mode) Yes vNoLets you turn the sound on or off in the attract mode.
Cabinet ConfigurationTwo-PlayervThree-PlayerSets the number of players who can use the game,
Auto Clear High Scores Yes v¥NoAutomatically clears the high score table periodically.
Clear High Scores Now YesNowImmediately clears the high score table in the self-test.
Display EPA ScreenYesvNo.Periodically displays the U.S. Environmental Protection

Agency (EPA) emblem and the message “Recycle, Don't Trash It!” in the attract mode. If this game is used outside of the U.S., we recommend you set this option to “No.”

v Manufacturer's recommended settings

Table 2-5 Game Option Settings

Game Options

Check and select the game options on this screen, shown in Figure 2-6. The screen shows the factory default settings in green. To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The game options, with defaults, are shown and explained in Table 2-5.

GAME OPTIONS |

DIFFICULTY LEVEL:

1USIC IN ATTRACT:

CABINET CONFIGURATION:

AUTO CLEAR HIGH SCORES:

LEAR HIGH SCORES NOW:

ISPLAY EPA SCREEN:

UP-DOWN SELECTS OPTION RIGHT-LEFT MODIFIES OPTION KICK RESTORES FACTORY SETTINGS START TO SAVE & EXIT '

]

Figure 2-6 Game Options Screen

Game Statistics

Use the information shown in the four statistics and histogram (bar graph) screens to keep track of your game use and maximize your profits. Record the information on the Guardians of the ‘Hood statistics page in the back of this manual. The first of the screens is shown in Figure 2-7. The game statistics are collected from the last time the statistics were cleared. You can clear the statistics by pressing the Punch button. Press any Defend button to advance to the next statistics or histogram screen, or to go back to the select test menu.

prc SRNR STATISTICS

LEFT COINS:

3 PLYR MINS: SESSIONS: NEW GAMES: CONT GAMES: NEW MINS: CONT MINS: ERROR COUN’ TOTAL CREDITS: 26 AVG TIME/CREDY AVG TIME/NEW GAME: 60 SEC AVG TIME/CONT GAME: 90 SEC O2MAR1992 03:28:15 O2MAR1992 06:56:04 PUNCH TO CLEAR STATS START FOR NEXT SCREEN asses Estas 78 SEC

Figure 2-7 Statistics Screen

Page 18

Cuarter 2~ SELF-Test % GUARDIANS OF THE HOOD

First Statistics Screen

The first statistics screen lists the following information:

  • Left Coins shows the number of coins counted in the left coin mechanism.
  • Right Coins shows the number of coins counted in the right coin mechanism.
  • Auxiliary Coins shows the number of coins counted on the auxiliary service coin inputs.
  • 0 Plyr Mins shows the number of minutes that the game was idle.
  • 1 Plyr Mins shows the number of minutes that the game was played by one person only. ° 2 Plyr Mins shows the number of minutes that the game was played by two people.
  • Session is measured from when the first player starts a game until the Game Over message appears.
  • New Games shows the number of unique games played. A unique game is counted every time a player starts a new game (not a continued game).
  • Cont Games shows the number of games that players continued.
  • New Mins shows the number of minutes that the game was played as new games.
  • Cont Mins shows the number of minutes that the game was played as continued games. ¢ Error Count shows the number of errors counted. in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 30E on the Guardians of the ‘Hood game PCB.
  • Total Credits is the number of credits accumulated by the game. « Average Time per Credit is displayed in seconds. This item is tabulated for all games played since the statistics were cleared. If there are no credits, this line will not be displayed.
  • Average Time per New Game is also displayed in seconds. ° Average Time per Continued Game is also displayed in seconds. Statistics 2 Screen

The next statistics screen (titled “Round Counts and Average Times”) lists the locale of each round. After the 13 locales, the screen shows how many players achieved those rounds and their average times playing those rounds.

New Game Time Screen

The next statistics screen (titled “New Game Time in Seconds”) lists the length of time for all new games, grouped in 20-second increments (except for the shortest games lasting 0-39 seconds).

Continuation Game Time Screen

The next statistics screen (titled “Continuation Game Time in Seconds”) lists the same information as the previous screen, except for continued games.

Session Time Screen

The next statistics screen (titled “Session Time in Minutes”) lists how long each session lasted. The bottom of the screen displays the median point for all session times. The median point represents half of all players above this point and half below.

Segment Screen The next statistics screen (titled “Segment at Which Player Quit”) lists which game segments players reached. The bottom of the screen displays the median point for all attained game segments.

Wave 1-4 Screens The remaining four statistics screens (titled “Who’s the most popular — Wave 1-4”) lists which characters were most often chosen by players at the start of each wave.

Alphanumeric Test

The alphanumeric test, shown in Figure 2-8, checks the condition of the alphanumerics in the game. If you see an error on the screen, check the EPROM at 15L. Moving any of the joysticks up or down scrolls the screen up and down. Press any Defend button to go to the select test menu.

Page 19

GUARDIANS OF THE "Hoop CHaprer 2 - Srir-Test

Figure 2-8 Alphanumeric Test Screen

Figure 2-9 Motion Object Test Screen

Motion Object Test

The motion object test screen, shown in Figure 2-9, tests the movement and color of various game objects. The most important part of this screen is the ROM status squares on the right side. The squares should all be green (indicating good motion object ROMs); red squares indicate bad ROMs. The squares are displayed the same way as the ROMs are installed on the game PCB — columns S and P and rows 9 to 2. Choose an object and move it or change it as follows: Control: This action results: Left joystick Left/right and up/down moves the object around on the screen. Up/down enlarges/shrinks the object. Right joystick Figure 2-10 Playfield Test Screen

Left Punch, Kick Selects one of the three motion objects (called 0, 1, and 2). Right Punch, Kick Selects a picture that will be displayed and manipulated as the motion object. Press any Defend button to go to the select test menu.

Playfield Test

The playfield test screen, shown in Figure 2-10, tests the movement of the playfield. Move the left joystick up, down, left, and right to check whether the whole picture moves accordingly. Press any Defend button to go to the select test menu.

Figure 2-11 Color Test Screen

2-7

Page 20

CHAPTER 2 — Seir-Test % GUARDIANS OF THE 'HooD

Color Test

This test has seven screens, the first of which is shown in Figure 2-11. Advance to each screen by pressing the Kick button. ¢ The first color test Gabeled “O-RGB”) indicates the dynamic range of the video display color circuit. The screen should show four bands (red, green, blue, and white, from top to bottom), ranging from bright to dark, left to right. The red, green, and blue bands are produced by only one color gun being turned on in each band. At the bottom is a white band, in which all three color guns are turned on.

  • The second color test (labeled “1-YCP”) shows the same as the first color test, but with two color guns being turned on in three bands — a yellow band (red and green guns), cyan band (blue and green _ guns), and purple band (blue and red guns). At the bottom is a white band.
  • The remaining screen numbers 2 through 6 are color purity tests. The rectangles of color shown are red, green, blue, white (“GREY Purity 1”), and grey (‘GREY Purity 2”). Each screen should display a straight rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If any of these screens are not correct, adjust the video display as described in the video display manual. Return to the select test menu by pressing any Jab button.

Convergence Test

The convergence test has four screens — white, violet, blue, and yellow grid lines. The white screen is shown

2-8 Figure 2-12 Convergence Test Screen

in Figure 2-12. To see the remaining screens, press any Kick or Jump button. Press any Jab button to go to the select test menu. Check the following on the screens:

  • The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel.
  • The convergence of the lines on the violet and black screens should be within 2.0 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manual.
Page 21

CHAPTER. 3

Troubleshooting and Maintenance

Introduction

{; HIS CHAPTER con- the game printed-circuit board,

tains troubleshooting tables and a list of ROM-caused problems

and repair procedures for your with specific ROMs to check and replace.

Guardians of the Hood” game. The chapter The chapter also has instructions for

includes several troubleshooting tables. The removing and replacing the video display, tables contain general troubleshooting infor- in addition to repair information for the

mation, the voltage levels and test points on joystick control.

Page 22

CuapTER 3 — TROUBLESHOOTING AND MAINTENANCE % GUARDIANS OF THE 'HOOD

Problem iggested Action

Coin Mechanism Problem

  • Check the wiring to the coin mechanism.
  • Check the voltage to the + side of the mechanism.
  • Test the coin mechanisms with the sound test screen in the self-test.

Game Play Problem

  • Check the harness and connectors.
  • Perform the self-test.
  • Check the voltage levels on the PCB. See Table 3-2, Voltage Inputs and Test Points.
  • Check What ROM Problems Look Like, Table 3-3, for specific ROM problems.

Control Problem

  • Check the harnesses and connectors.
  • Check the switches on the control.
  • Ifyou took the control apart, have you reassembled it correctly? 4, Make sure all the parts on the control are in good repair. Repair or replace parts.
  • Is the “Cabinet Configuration” option in the self-test game options set correctly?
NOTE: The joysticks and pushbutton switches do not require lubrication.

Sound Probiem

  • Is the speaker volume turned up? (Volume is adjusted digitally in the self-test.)
  • Check the voltage on the PCB edge connector.
  • Check the wiring from the PCB to the speaker.
  • Check the voltage level to the PCB. See Table 3-2, Voltage Inputs and Test Points.
  • Replace the speaker.

Video Display Problem Screen is dark. Is the game plugged in? Is the game turned on? . Are the connections good? . Is the line fuse good? . Is the display brightness turned up? . Are the solder connections on the line filter and transformer good? . Is the edge connector on the PCB tightly connected? . Check all of the items below. If you answer no to any question, you have a problem with the video display, not with the game circuitry. See your video display service manual. a. Do you have power to the video display? b. Are the video displays filaments lit? c. Do you have high voltage to the video display?

  • Are the voltage levels to the video display PCB correct? (Power voltage is 110 VAC. Video signal voltage is 0.5 to 3.5 Volts.) 10.If the level is not correct, check the connectors and the harness. OPNOMAWNH

Only a colored screen appears. You probably have a serious RAM problem.

Display area wavers or is too small.

  • Do you have correct power voltage to the video display PCB?
  • Do you have correct high voltage to the video display?

Picture is wavy.

  • {fs the monitor ground connected to the monitor?
  • Are the sync inputs connected properly?

Picture is upside down. When you serviced the display, you connected the wires incorrectly. Switch the horizontal or vertical yoke wires on the display.

Convergence, purity or color probiems. Use the screens in the self-test (see Chapter 2) to adjust the video display. Use the adjustment procedures in your video display manual.

Picture is not centered. Use the centering procedures in your video display manual.

Table 3-1 Troubleshooting Table

Page 23

GUARDIANS OF THE'HOOD *% CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

Voltage Test Point or LED

+5 + 0.25 VDC +5V1 Source and Purpose

Logic power from the switching power supply. CR3 LED (Game PCB) open. Lights when 5 V is applied to the PCB and the reset (RST) jumper is

CR9 LED (JSA Audio tll PCB) CR3 LED (JSA Audio Ili PCB) Lights when the +12 V supply is good. Lights when the -5 V supply is good. +12V +VOP (pin 4 of LM324) +12 V from the switching power supply. Positive supply for the analog circuitry. -5V -VOP (pin 14 of LM324) -5V from the switching power supply (if connected). Negative supply for the analog circuitry.

Table 3-2 Voltage Inputs and Test Points on the PCBs

Maintaining the Coin Mechanism

The coin mechanism should be cleaned every three months. For detailed parts information on the coin door, see Figure 4-3. To maintain the coin mechanism:

  • Turn power off to the game. Open the upper coin door.
  • Open the gate on the door covering the magnet. Use the blade of a screwdriver to scrape away any metal filings collected on the magnet.
  • Fora thorough cleaning, wash the coin mechanism in hot soapy water. Use a toothbrush to remove any stubborn build-up of residue in the coin path.
  • Dry the coin mechanism with compressed air.
  • If you do not want to use water, brush the loose dust off with a soft brush and scrub the residue in the coin path with a toothbrush. Blow out all the loose dust and dirt with compressed air.
NOTE Never lubricate the coin mechanism with oil or grease.

Repairing the Video Display

The video display frame in this cabinet is designed to be used with both horizontal- and vertical-mounting displays, as well as 19- and 25-inch displays.

Removing the Video Display

If you have a problem with the video display, first run the self-test procedure to narrow down the cause. To make adjustments to the video display, unlock the service door on the rear of the cabinet. If you want to repair the video display, remove it from the game by following this procedure:

  • Tum the game power off and wait two minutes. Unplug the power cord for safety.
  • While you wait, unlock the upper rear service door on the cabinet.
  • Remove the three screws that attach the attraction shield retainer, and remove the retainer, shield, and attraction film. Then remove the display shield, cardboard bezels, and cleats in front of the display.
Page 24

‘CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE % GUARDIANS OF THE "HOOD

ProblemROM Causing the ProblemCheck the ROM ai

Program works, but the motion objects objects are missing or bad Graphics Playfield: 20D-21D. Motion Object High: 28-78. Motion Object Low: 2P-7P. Alphanumerics: 22J.

Garbage on screen; program doesn’t workProcessor14C

Program ROM 0 8D, 8C

Game program is erratic.Program ROM 19D, 9C.

No sound or erratic sound Audio ROM: Audio Program 120 Audio ADPCM 19E

Table 3-3: What ROM Problems Look Like

WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not service this display unti! you observe all precautions necessary for working on high-voltage equipment. X-Radiation This video display is designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube (CRT) may implode if Struck or dropped. The shattered glass from the tube may cause injury up to six feet away. Use care when handling the display and when removing it from the game cabinet. Also, wear gloves to protect your hands from the sheet-metal edges.
  • Remove the four nuts and washers that secure the video display.
  • Discharge the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Attach one end of a solid 18-gauge wire to a wellinsulated screwdriver or wooden handle. b. Attach the other end of the wire to an earth ground. ¢. Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait two minutes and repeat part c. a Disconnect the harness connectors from the video display.
  • Pull the video display assembly out of the cabinet. Be extremely careful.

Replacing the Video Display

Perform the following procedure to replace the video display in the cabinet.

  • Carefully lift the video display into the cabinet.
  • Install the nuts that hold the video display assembly. 3, Connect the power and signal harnesses to the video display. If you replace the CRT and yoke together, adjust the brightness, size, and centering as described in the vid- €o display service manual. Check the purity and convergence according to that manual, but adjust both only if required.
  • Install the cardboard bezel, video display shield, and cleats. Replace the attraction film, attraction shield, and retainer.
  • Lock the rear service door on the cabinet.

RAM Error Loca Screen Color

Red Working RAM

Green Playfield RAM Blue Motion Object RAM Table 3-4 Screen Colors Indicating Bad RAMs

Page 25

GUARDIANS OF THE "HOOD % CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

99-215030 Black Knob and Shaft

99-215031 Pivot Cylinder

99-215018 Spring 1" Diameter

99-215011 #8 x .75 Screw (4 places)

99-215036 Microswitch Actuator

99-215015 E-Ring 160044-001 -187 Microswitch

99-215010 #4 x 75 Screw (8 places)

99-215031 Pivot Cylinder

Figure 3-1 Maintaining the Joystick Control

Page 26

‘CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE “ GUARDIANS OF THE 'HOOD

Removing and Replac-

Removing and Replac ing the Joystick Control

The joystick control is shown in Figure 3-1. If you want to repair this control, remove it from the control panel. To repair the joystick, disassemble it by removing the retaining ring at the bottom of the shaft. To replace any of the four switches, remove the two screws that secure each switch.

ROMs and RAMs

If you have think you have bad ROMs or RAMs, run the self-test. If you see only a colored screen and cannot enter the self-test, see Table 3-3. Also refer to Table 3-4 if you think you have a RAM problem.

3-6

Page 27

Parts Illustrations

Part Ordering Information

HIS CHAPTER provides in- and the serial number of your game.

formation you need to order With this information, we can fill

m parts for your game. The your order rapidly and correctly.

PCB parts lists are arranged in. alpha- We hope this. will create less betical order by component. Within A downtime and more profit from each section the parts are arranged your games. Atari Games Customer

numerically by part number. g When : Service phone numbers are listed on

you order parts, give the part number, the inside front cover of this

part name, the number of this manual, manual.

Page 28

(Cuaprer 4— Parts ILLUSTRATIONS “% GUARDIANS OF THE ‘HOOD.

046s25.011752630601| o5a152.02oas07s.c1| o3¢926-01re=
Glass Retainer 1/2" W.x 1/16"Bezel W/Black BezelUpper Retainer1OTE: peers eae
7538160Viryi Foam Tape| Graphles1¥78056-002‘reots-cta
weaaxt”— 170269-1202._|178056-002ve w.xtnet,| 48x34 $9, Dr.
FxScrewaa W.xt8T.[]a12 Wax tne.Foam aveupwscon;
Cakes)Vint oan Tepe ||Faam Tepepieces,8‘7aon3-01up
| ene)04692601ar Wx V8".171085-901

Lower Retainer || Vinyl Foam Tape Flourescent Lamp Fixture seni8-712 $76015-110, #9306 SO. #10518" Panstd, Screw LPW Seow places) (places) 7922001 ‘174269-0802 | Lamp Retaining Cin ile wex eT paces) : Vinyl Foam Tape 046928.01 aos7otten

rr Atvaction ShieldSpoater Pans! Assyen

; 50.02 (optional , 402 & 423)

\\sor!ri38x 1114"Sa, De. Scaw | optional 40%
\Aracton Fim(apiaces)a
ji“14-20 NutWasher Assy.

VV (Bplaces) 17507002 Fat Washer pieces) \

| oase27-01 Display Shee 76025-4420" oeraraot aiaz0 x ve" sii sv-375'| Bute Soew| eBcee)

set-Test LabVapaces)(2 Paces)

175014.3050° taxi 145g, +e Flat Washer Dn Sew (4 places) i | | (Places) l eres 4 Mounting Frame 728516 vazox 1 A0se17901" I en Screw Control Panel Coa) soy. 114" Exernal Lock Washer (4 Paces) 179013-007" Drawer Latch (2plces) sre0is-112" foxsie" Pant. Screw a. (eplaces| ~

paaoans.or"|:A2

Conuol Pos n050189-01 JANMA Power Supply Assy. sTa1S. 112 ° sox Sie Part. “Tapping Serew (a Places) #177026-0098 ‘8050180-01" ese Nu covaipows| J aa Aas. iain iis ra0sors71 Board Set assy.

‘apace|cuarsan PE Ass.
Pan. ScrewPatWasher17817-1612"-ao4e2e9-01
(Splaces)" (Aplaces)V6" Roundain Hares Assy
175017-2005"stand-off175004706
V4" Split-7216068"FiberWasher
Lock Waster62x38")“AOSUIEEDT(4 Paces)
:(places)Parca. Screw |Drawer Assy.*954536-15
peg(2places)|~0s0167-01Foam Visation
WUEZxZ_rsoteater’|woos DrawerDamper
joxHd. Boh#8 Fiwesher|175008002| ) g7apag-o07a72-6512
(4 places)‘2places)|NylanWasher ||222 Gorn Door Assy,fatale$6 x30Pan.
arrbap-o04e§w7sbt7-a01s |epiaces)| | Soegr 40weta, Soem
14-20 Nav#6 spi |TETSU ae screweeRoss
Washer Assy.LockWather | 0x1" Par.| Ggeiseoracre este
(places)feptces)|"Tapping Screw’| Product. Labelnce)

Figure 4-1 Cabinet-Mounted Assemblies, Front View A050190-01 D

4-2

Page 29

GUARDIANS OF THE "Hoop “ CuHapter 4 — Parts ILLUSTRATIONS

items Not Shown:

noar603-02 Display Power Harress Assy. osesa9-01 ‘A087607-01 Wood Cabinet Wea ges Assy (036086-01 ‘Shock Warring Label -A049663-01 places) ‘ONOFF Switch assy. 036158-01 $76015-110 Product 1D, Label #10x518" Pan-H, 178126-002 Tapping Screw 892" Tamper-proof places) Hexsey Driver : ‘04esst-01 ‘3050188-01 48 Grounding Jumper Assy. ‘Wood Vendor Kit List n088493-02 THs20 138° Grounding Jumper Assy. Wells Garcrer 25° Color 1770284038, Display Service Manual #8-32 NutWasher Assy. TMa75 Operator Marval

050149-01 Side Pare! Decal (e places)

047876-01 Rear Door 176020220 0x 1118" LPW Screw ‘4 places) on7985-01, cover 476010212 #8x36' Sq. Drive Screw 043938.01 (6 places) Leg Leveler Plato 176015-112 #0 x9 Pan-Hd. Sow (16 places) 178255-008, 918-36 x112" *176083-007 ‘Adjustable Gide | Fan Guard (4 places)

Figure 4-1 Cabinet-Mounted Assemblies, Front View

A050190-01 D

Page 30

(CHAPTER 4 — Parts ILLUSTRATIONS % GUARDIANS OF THE "HOOD.

176015-110 #10 x S/S" Pan-Hd. Tapping Screw (places) (Not part of Control Panel Assy.) 171099-001 &-Position Gold Joystick Assy. (3 places)

178237-008 Blue Button Assy. (S places)

050151-02 Control Panel Decat|

‘A050179-01 Control Panel Assy. 05017501 Control Panel (050181-01 Control Pane! Backup (Not part of Controy Pane! Assy.)

Control Ped Assy.

Control Mounting Bracket items Not Shown:

. 05019201 '75.5112B 1 #10-24 x 24" Carriage Bo | Comal Harnens Assy. (12 places) #10 x 9/6" X-Rec, Pan-Hd, 175014-1040 ‘Tapping Screw #10 Flat Washer (Splaces) (12 places) 177010-240 +#10-24 Hex Polymer Locknut [12 places) | 176025-4420 114-20 x 1/6" Tamper proof But-Ha. Screw (4 places) 175014-3050 1/4" Flat Washer (4 places) (hese two items are not part of the 160044-001 | Control Panel Assy.) | snap-Acfion Switch (10 places) 178237-002 | ‘Yellow Button Assy. i i Splaces) It

i! —— ' if | i | H y ! i a | 1% 1 | lA te | L I t & : raver Ase.

Figure 4-2 Control Panel Assembly

A050179-01 B

Page 31

GUARDIANS OF THE HOOD % CHAPTER 4 -- PaRTs ILLUSTRATIONS

99-215030 Black Knob and Shaft |

99-215032 Washer

99-215031 Pivot Cylinder

‘ tte

99-215033 Hub

99-215018 Spring 1" Diameter

99-215035 Z-Stop

99-215034 Bracket

99-215011 #8 x .75 Screw (4 places) 160044-001 -187 Microswitch

99-215010 #4 x .75 Screw x (8 places)

99-215036 Microswitch Actuator

99-215031 Pivot Cylinder 99-215015 E-Ring [——"<)

Figure 4-3 Joystick Assembly

171099-001

Page 32

Carrer 4 — Parts ILLUSTRATIONS % GUARDIANS OF THE ‘HOOD

99-15096. — 99-15025, Coin Inlet. Left

99-15113 Key Hook

99-15056 Screw for Bezel 1

‘Sw. Adjuster

99-15056 | Screw

99-15131 Elastic Locknut | 99-15132 Snap-on Sleeve

99-15130 ‘Snap-on Clip

99-15133 Hold Down Bracket

99-15128 NuvWasher for MWS Mounting Screw Coin Ret. Plate

(2 places)

99-15051 Lamp Holder

99-15029 Bracket

99-15042 ‘Switch 99-15086 Coin Mechanism

Mounting Stud }~ Ad eo ee \ 99-15104 Base Plate W/Pivot & Studd

99-15026 S\ Right Coin inlet N

99-15056 ‘Screw for Bezel

99-15028 Coin Ret. Box

99-15056 ‘Screw for Bezel

99-15134 - |4-40-1" Pan-Head Screw

MIS Flat-Head Mounting Screw

99-15085, Coin Door Harness

Figure 4-4 Coin Controls, Inc. Coin Door Assembly

171093-001

Page 33

GUARDIANS OF THE "HOOD “ CHAPTER 4 — PaRTS ILLUSTRATIONS

99-15038: 99-15036 Bezel for Button Cover

99-15001 thru 99-15012 Retum Button

99-15039 Bezel for Cover

99-15125 Frame Hinge Screw | | L

< Ee 99-15052 Spring for Button

S 9815110 |99-15088 Enclosure a Clamp

a 7 99-15135 > Frame Clamp Screw

a

99-1516 Upper Door [~

9915115 Lower Door

: 99-15114 ! Die Cast Frame |

\

\ : : fi

i rae i - I sg q 99-15111 1 Coin Counter

98-15089 99-15127 Lock Assy pttip ted Meter Mounting ‘Screw

Figure 4-4 Coin Controls, Inc. Coin Door Assembly, Continued

171093-001

Page 34

Cuapter 4 — Parts ILLUSTRATIONS “ GUARDIANS OF THE HOOD

NOTES

Page 35

GUARDIANS OF THE Hood * CuapTer 4 ~ PARts ILLUSTRATIONS

149014-001 179281-102 BV, 7A Switching 2 Position Terminal Block ‘TR-HAGGOES 48-22 x 2/8" K-Rec 148-92 x 3/8" X-Rec ‘Thd. Form Screw ‘Thd. Form Screw (2 places) 2 places)

a049293-07 UW, 10° 5V Jumper Assy, ‘A049295-01 6 Black AC Jumper Assy. ‘A049295-02 6° White AC Jumper Assy. A049296-01 PS Gnd Jumper Assy.

A042984-01 Filter Line Assy. ‘T2HAA606S #692 x 3/8" X-Rec ‘Tho. Form Screw (2 places)

| a049967-01 4° Black Jumper Assy.

| 937620-01 Power Suppy | Warning Label i i i i i

120V, 1.5A isolation 2 Position Fuse Block ‘Transformer ‘72HAaB0ES #8032 x 3/8" X-Rec ‘Tha Form Screw (4 places) 95-32 318 X-Rec, ‘Thd Form Screw (2 places)

Figure 4-5 Power Supply Assembly

A050193-01 A

4-9

Page 36

Figure 4-6 Guardians of the “Hood Game PCB Assembly A049757-07 A

Page 37

GUARDIANS OF THE "HOOD # Ca#arTER 4 — PARTS ILLUSTRATIONS

Guardians of the ‘Hood Game PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
Sockets2/34Integrated Circuit, 7415260137332001
2/3FSocket, 44 Pin, Plec179237-0442/3FASIC 65136092-0012
2cSocket, 24 Pin, 300179259-0242ARes, R/2R, 1K/2K118016-001
2P, 28Socket, 32 Pin, .600179257-0322BIntegrated Circuit, 74F374137420-001
3cSocket, 24 Pin, .300179259-024

2c Integrated Circuit, RAM, 2K x 8,

3KSocket, 20 Pin, .300179259-02035 ns, .3137534-001
3P, 3SSocket, 32 Pin, .600179257-0322DIntegrated Circuit, 7418374137144-001
4/5M, 4M_ Socket, Zip 28179302-0282Integrated Circuit, 74F32137486-001
4P, 45Socket, 32 Pin, .600179257-0322K“Integrated Circuit, 74F169137496-001
5cSocket, 24 Pin, .600179257-0242MIntegrated Circuit, 7418377137145-001
5MSocket, Zip 28179302-0282PEPROM, 150 ns, 512K x 8136092-0040
5P, 5SSocket, 32 Pin, .600179257-03228EPROM, 150 ns, 512K x 8136092-0041
6cSocket, 20 Pin, .300179259-0203/48Integrated Circuit, 74LS260137332-001
6P, 6S, 7P, 78, 8C, 8D, 8P, 8S3ARes, R/2R, 1K/2K118016-001
Socket, 32 Pin, .600179257-0323BIntegrated Circuit, 74F374137420-001
9/10FSocket, 68 Pin, PLCC179237-0683C.Integrated Circuit, RAM, 2K x 8,
9C, 9D, 9P, 98, 10C, 10D, 11C, 11D35 ns, 3137534-001
Socket, 32 Pin, .600179257-0323DIntegrated Circuit, 7418374137144-001
11sSocket, 20 Pin, .300179259-020
3FIntegrated Circuit, 74F02137481-001
12FSocket, 40 Pin, .600179257-0403yIntegrated Circuit, 7418377137145-001
14B/CSocket, 64 Pin, .900179256-0643KGALI6V8, 25 ns136092-0005
14FSocket, 24 Pin, .300179259-0243MIntegrated Circuit, 74LS157137029-001
15FSocket, 20 Pin, .300179259-020
3PEPROM, 150 ns, 512K x 8136092-0042
15NSocket, 28 Pin, .600179257-02838EPROM, 150 ns, 512K x 8136092-0043
177Socket, 20 Pin, .300179259-0204/5MIntegrated Circuit, VRAM, 256K x 4,
17NSocket, 28 Pin, .600179257-028100 ns137682-100
18E,18JSocket, 40 Pin, .600179257-0404ARes, R/2R, 1K/2K118016-001
20/21C, 20/21D, 20C, 20D4BIntegrated Circuit, 74HCT273137655-001
Socket, 32 Pin, .600179257-0324cIntegrated Circuit, 7418244137038-001
20PSocket, 20 Pin, .300179259-0204DIntegrated Circuit, 7418374137144001
20R/S.Socket, 68 Pin, PLCC179237-0684EIntegrated Circuit, 74F138137521-001
211, 21PSocket, 20 Pin, .300179259-020
4FIntegrated Circuit, 7415378137305-001
22C,22D,22J Socket, 32 Pin, .600179257-0324gIntegrated Circuit, 74F153137492-001
22PSocket, 20 Pin, .300179259-0204KIntegrated Circuit, 74L$153137104-001

4M Integrated Circuit, VRAM, 256K x 4, Integrated Circuits 100 ns 137682-100

1AIntegrated Circuit, 7406137052-0014PEPROM, 150 ns, 512K x 8136092-0044
1BIntegrated Circuit, 74HCT273137655-0014SEPROM, 150 ns, 512K x 8136092-0045
1cIntegrated Circuit, 7418244137038-0015cIntegrated Circuit, 28C16-200, 200 ns137648-200
1DIntegrated Circuit, 7415374137144-0015D, 5EIntegrated Circuit, 74174137023-001
1EIntegrated Circuit, 74LS244137038-001SFIntegrated Circuit, 74F32137486-001
yIntegrated Circuit, 74F260137570-001syIntegrated Circuit, 74F153137492-001
1KIntegrated Circuit, 7418378137305-0015KIntegrated Circuit, 7415153137104-001
1MIntegrated Circuit, 74LS157137029-0015MIntegrated Circuit, VRAM, 256K x 4,

100 ns “137682-100

Page 38

CuapTer 4 — Parts ILLUSTRATIONS “ GUARDIANS OF THE "HOOD

Guardians of the "Hood Game PCB Assembly

Designator Description 5P EPROM, 150 ns, 512K x 8 38 EPROM, 150 ns, 512K x 8 6/7 Integrated Circuit, 74F260 6c GALI6V8, 25 ns 6D Integrated Circuit, 74F74 6E Integrated Circuit, 74L$74 OF Integrated Circuit, 741532 oy Integrated Circuit, 74F153

6K Integrated Circuit, 741S153 6M Integrated Circuit, 7415377 oP EPROM, 150 ns, 512K x 8 68 EPROM, 150 ns, 512K x 8 7/8) Integrated Circuit. 7418273 TF Integrated Circuit, 741886 q Integrated Circuit, 74F153 7K Integrated Circuit, 7415153

7™ Integrated Circuit, 7415244 7P EPROM, 150 ns, 512K x 8 7s EPROM, 150 ns, 512K x 8 8/9 Integrated Circuit, 7418273 8A/B Integrated Circuit, 74F245 8C EPROM, 150 ns, 128K x 8 8D EPROM, 150 ns, 128K x 8 8K/L Integrated Circuit, 741S153 8M Integrated Circuit, 741$244 9/10F FPLA SA/B Integrated Circuit, 7415245 9c EPROM, 200 ns, 128K x 8

9D EPROM, 200 ns, 128K x § OK Integrated Circuit, 7497 OM Integrated Circuit, 747273 10A Integrated Circuit, 74LS257 10A/B Integrated Circuit, 7418245 10K Integrated Circuit, 74L$378 10L Integrated Circuit, 7497 11/12A/B_ Integrated Circuit, 7415174

1A Integrated Circuit, 74LS$257 MA/B Integrated Circuit, 741$174 11K, 11L Integrated Circuit, 74F169 11N Integrated Circuit, 7415377

11P Integrated Circuit, 74LS157 11S GAL16V8, 25 ns 124/B Integrated Circuit, 74F245 12¢/D Integrated Circuit, 74F244

4-12 Parts List, Continued

Desig-

Part No.natorDescriptionPart No.
136092-004612FIntegrated Circuit, SOS137550-001
136092-004712KIntegrated Circuit, 74F153137492-001
137570-00112L,12N,12P Integrated Circuit, 74F169137496-001
136092-000913D/E,13E Integrated Circuit, 74F04137437-001
137436-00113FIntegrated Circuit, 74F02137481-001
137023-00113Integrated Circuit, 74F174137532-001
137019-00113LIntegrated Circuit, 7418245,+ 137134-001
137492-00113N,13P,13R Integrated Circuit, 74F153137492-001
137104-001144Integrated Circuit, 7415257137136-001
137145-00114B/CIntegrated Circuit, 68000, 16 MHz — 137669-0001
136092-004814D/EIntegrated Circuit, 74F244137502-001
136092-004914FGAL6001, 35 ns136092-0010
137040-00114qIntegrated Circuit, 74F04137437-001
137079-00114KIntegrated Circuit, 74F00137327-001
137492-00114LIntegrated Circuit, 741S245137134-001
137104-00114NIntegrated Circuit, 74F374137420-001
137038-00114PIntegrated Circuit, 7418374137144-001
136092-005014R, 148Integrated Circuit, 74F153137492-001
136092-005115aIntegrated Circuit, 7418257137136-001
137040-00115B/C _ Integrated Circuit, 741874137023-001
137591-00115CIntegrated Circuit, 741S148137417-001
136092-002015DIntegrated Circuit, 74F20137530-001
136092-002115EIntegrated Circuit, 74F244137502-001
137104-00115FGAL1OV8, 25 ns136092-0007
137038-00115LIntegrated Circuit, 74F153137492-001
136092-000415NIntegrated Circuit, RAM, 32K x 8,
137134-00170 ns, .6137615-070
136092-002215R, 15SIntegrated Circuit, 74F163137345-001
16B/CIntegrated Circuit, 74F08137483-001

136092-0023

137090-00116CIntegrated Circuit, 74F163137345-001
137610-00116DIntegrated Circuit, 74F74137436-001
137136-00116EIntegrated Circuit, 74F32137486-001
16FIntegrated Circuit, 74F138137521-001

137134-001

137305-00116K/L _ Integrated Circuit, 74F153137492-001
137090-00116LIntegrated Circuit, 74F00137327-001
137122-00116R, 168Integrated Circuit, 74F163137345-001
17AIntegrated Circuit, 7418244137038-001

137136-001

137122-00117A4/BIntegrated Circuit, 741$197137240-001
137496-00117B/C _ Integrated Circuit, 74F32137486-001
137145-00117DIntegrated Circuit, 74F04137437-001
17E,17FIntegrated Circuit, 74F138137521-001

137029-001

136092-001117GALI16V8, 25 ns136092-0008
137591-00117kIntegrated Circuit, 741245137134-001
137502-00117NIntegrated Circuit, RAM, 32K x 8,

70 ns, .6 137615-070

Page 39

GuaRDIANS OF THE HOOD CHAPTER 4— PaRTS ILLUSTRATIONS

Guardians of the ‘Hood Game PCB Assembly Parts List, Continued

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
17R,17SIntegrated Circuit, 74F163137345-001Capacitors

C1,C2 Capacitor, 100 pF, 100 V, 45%,

184,Tategrated Circuit, 74LS257137136-001Ceramic122016-101
18A/BIntegrated Circuit, 74F0S8137483-001C3-C6Capacitor, .1 UF, 50 V, +80%-20%,
18B/CIntegrated Circuit, 7415153137104-001Ceramic122002-104
18EIntegrated Circuit, SOS137550-001C7-C10Capacitor, .01 UF, 50 V, +80%-20%,

Ceramic 122002-103

18)Integrated Circuit, PFHS137419-104C11, C12Capacitor, 1000 pF, 100 V, 10%,
18LIntegrated Circuit, 741S245137134-001Ceramic122015-102
18NIntegrated Circuit, 74F374137420-001
18P, 18SIntegrated Circuit, 741$244137038-001C13-C17_—_Capacitor, 100 pF, 100 v, +5%,

Ceramic 122016-101

19AIntegrated Circuit, 74L$257137136-001C18-C42Capacitor, .01 UF, 50 V, +80%-20%,
19CIntegrated Circuit, 74LS298137201-001Ceramic122002-103
19FIntegrated Circuit, 74F04137437-001C43,Capacitor, 100 IF, 16 V, Electrolytic,
19)Integrated Circuit, 74L$378137305-001Radial123013-107

C44, C45 Capacitor, .1 UF, 50 V, +80%-20%,

19KIntegrated Circuit, 7419163 A137114-001Ceramic122002-104
19LIntegrated Circuit, 74F86137649-001
19NIntegrated Circuit, 7419374137244-001C46Capacitor, 100 pE, 100 V, +5%,
20/214Integrated Circuit, 74FOO137327-001Ceramic122016-101

C47, C48 Capacitor, .1 UF, 50 V, +80%-20%,

20/21CEPROM, 200 ns, 128K x 8136092-0034Ceramic122002-104
20/21DEPROM, .200 ns, 128K x 8136092-0033C49-C55Capacitor, 100 pF, 100 V, +5%,
20/21FIntegrated Circuit, 74LS378137305-001Ceramic122016-101
20/21)Integrated Circuit, 74L$157137029-001C56Capacitor, .1 HF. 50 V, +80%~20%,

Ceramic 122002-104

20/21KIntegrated Circuit, 74L$377137145-001
204Integrated Circuit, 7418175137123-001C57-C60Capacitor, 100 pF, 100 V, +5%,
20CEPROM, 200 ns, 128K x 8136092-0036Ceramic122016-101
20DEPROM, 200 ns, 128K x 8136092-0035C61-C74Capacitor, .1 UF, 50 V, +80%~-20%,

Ceramic 122002-104

20FIntegrated Circuit, 7418377137145-001C75Capacitor, 1000 pF, 100 V, +5%,
20), 20KIntegrated Circuit, 741163 A137114-001Ceramic122016-102
20LIntegrated Circuit, 74F138137521-001C76Capacitor, .01 UF, 50 V, +80%-20%,
20NIntegrated Circuit, 74F163137345-001Ceramic122002-103
20PPROM, 828147136092-0001C77Capacitor, 1000 pF, 100 v, +5%,
20R/SIntegrated Circuit, CPU, PLCC137658-101Ceramic122016-102
21FIntegrated Circuit, 7415378137305-001C78-C88Capacitor, .1 UF, 50 V, +80%~20%,
2LGAL16V8, 25 ns136092-0006Ceramic122002-104

C89 Capacitor, 100 pF, 100 V, +5%,

21NIntegrated Circuit, 74F163137345-001Ceramic122016-101
21PPROM, 828147136092-000390, C91, C93-C169
22EPROM, 200 ns, 128K x 8136092-0032Capacitor, .1 uF, 50 V, +80%-20%, Cer. 122002-104
22DEPROM, 200 ns, 128K x 8136092-0031

170, C171 Capacitor, 10 pF, 100 Vv, +5%, Cer. 122016-100

22)EPROM, 200 ns, 128K x 8136092-0030C172-C200 Capacitor, .2 UF, 50 V, +80%-20%,
22LIntegrated Circuit, 74LS151137101-001Ceramic122002-104
22NIntegrated Circuit, 74F163137345-001C201, C202 Capacitor, 100 pF, 100 Vv, +5%, Cer.122016-101
22PPROM, 828147136092-0002€203-C282 Capacitor, .1 UF, 50 V, +80%~-20%, Cer. 122002-104
22RIntegrated Circuit, 7418379137374-001

4-13

Page 40

CHAPTER 4 ~ PARTS ILLUSTRATIONS “% GUARDIANS OF THE "HOOD.

Guardians of the "Hood Game PCB Assembly

4-14 : Parts List, Continued

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
DiodesR82, R83_Resistor, 470 Q, +5%, 1/8 W110027471
CR1, CR2Diode, 1N4001131048-001R84, R85_—_Resistor, 1 K Q, 45%, 1/8 W110027-102
CR3Diode, MV5053, Light-Emitting331027-002R86Resistor, 470 Q, +5%, 1/8 W110027-471
R87Resistor, 1 K Q, +5%, 1/8 W110027-102

Test Points, Connectors, and Inductors

GND1, 2Test Point179051-001R88-R90Resistor, 470 Q, 5%, 1/8 W110027-471
yuConnector, 11 Circuit, Header, .100R9I-R93_—_—Resistor, 1 K Q, 45%, 1/8 W110027-102
Ctr, Key 2179118-011R94Resistor, 220 Q, 5%, 1/8 W110027-221
J4,J9, J10 Connector, 2 Circuit, Header, .100 Ctr 179048-002R95, R96Resistor, 100 Q, +5%, /8 W110027-101
JAUDConnector, 36 Ckt, .1 Header, Long179300-036
ROV-R105Resistor, 10 K Q, 45%, 1/8 W110027-103
JPLConnector, 15 Ckt, Header, .100 Ctr 179118-015R106Resistor, 240 Q, +5%, 1/8 W110027-241
JSYNCConnector, 3 Ckt, Header, .100 Ctr.179048-003R107Resistor, 100 K , +5%, 1/8 W110027-104
STESTConnector, 2 Circuit, Header, 100 Ctr 179048-002R108Resistor, 10 K Q, 45%, 1/8 W110027-103

VCR Connector, 2 Circuit, Header, .100 Ctr 179048-002 R110-R112 Resistor, 1 K Q, £5%, 1/8 W 110027-102 -WDOG — Connector, 2 Circuit, Header, 100 Ctr 179048-002 R113, R117, R118

uInductor, 100 UH141024-001Resistor, 10 Q, +5%, 1/8 W110027-100

R119-R121 Resistor, 1 K Q, +5%, 1/8 W 110027-102

TransistorsR122Resistor, 10 Q, +5%, 1/8 W110027-100
Q1-Q3Transistor, 2N3904133041-001
Q4Q7Transistor, 2N5306133033-001R123-R125 Resistor, 10 K Q, +5%, 1/8 W110027-103
QsTransistor, 2N3904133041-001R126Resistor, 10 Q, +5%, 1/8 W110027-100
R127Resistor, 10 K Q, +5%, 1/8 W110027-103
ResistorsR128-R130 Resistor, 1 K Q, 45%, 1/8 W110027-102
RIResistor, 100 Q, +5%, /8 W110027-101
R2Resistor, 15 Q, +5%, 1/8 W110027-150R131Resistor, 100 Q, 45%, 1/8 W110027-101
R3Resistor, 100 Q, +5%, 1/8 W110027-101R132, R133 Resistor, 10 K Q, 15%, 1/8 W110027-103
R4Resistor, 15 Q, +5%, 1/8 W110027-150R134Resistor, 100 Q, +5%, 1/8 W110027-101
R135“Resistor, 470 Q, 45%, 1/8 W110027-471
RSResistor, 100 Q, +5%, 1/8 W110027-101
R6Resistor, 15 Q, +5%, 1/8 W110027-150R136Resistor, 10 K Q, 45%, 1/8 W110027-103
R7-R9_Resistor, 470 Q, +5%, 1/8 W110027-471R137, R139, R140
R10Resistor, 2.4 K Q, +5%, 1/8 W110027-242Resistor, 10 Q, 45%, 1/8 W110027-100
RMIResistor, 1 K Q, 45%, 1/8 W110027-102
RILResistor, 1 K Q, +5%, 1/8 W110027-102R143, R144 Resistor, 10 Q, £5%, 1/8 W110027-100
R12Resistor, 10 Q, +5%, 1/8 W110027-100
R13Resistor, 2.4 K Q, 45%, 1/8 W110027-242R145-R150 Resistor, 1 K Q, 45%, 1/8 W4110027-102
R14Resistor, 1 K Q, 45%, 1/8 W110027-102RIS1Resistor, 470 Q, 45%, 1/8 W110027-471
RISResistor, 10 Q, 45%, 1/8 W110027-100Crystals
RIGResistor, 2.4 K Q, +5%, 1/8 W110027-242X1Crystal, 20.000 MHz144000-003
RI7Resistor, 1 K Q, +5%, 1/8 W110027-102x2Crystal, 14.318 MHz144000-004
RIS.Resistor, 10 Q, 45%, 1/8 W110027-100
R19Resistor, 0 Q, 45%, 1/4 W110005-001
R20-R45_—_Resistor, 1 K Q, +5%, 1/8 W110027-102

R4G-R48, R50, R52-ROS Resistor, 470 Q, +5%, 1/8 W 110027-471

R66, R67Resistor, 10 K Q, +5%, 1/8 W110027-103,
R68, R6DResistor, 470 Q, 5%, 1/8 W110027-471
R70-R73_Resistor, 1 K Q, $5%, 1/8 W110027-102
R74, R77Resistor, 470 Q, +5%, 1/8 W110027-471
R78-R81__Resistor, 1 K Q, 45%, 1/8 W110027-102
Page 41

GUARDIANS OF THE "HOOD % CuarTeR 4 — Parts ILLUSTRATIONS

NOTES

Page 42

CuapTer 4 ~ ParTs ILiusTRATIONS “ GUARDIANS OF THE "HOOD

*2 ED oO a Se] g Ls74 KG} = a

Figure 4-7 JSA Audio lil PCB Assembly A048974-10 A

Page 43

GUARDIANS OF THE "HOOD “ CHAPTER 4 — PaRTs ILLUSTRATIONS

JSA II PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
Sockets16A,Integrated Circuit, 7418374137144-001
8DSocket, 16 Pin, .300179259-01617BIntegrated Circuit, 74F74137436-001
9C1Socket, 24 Pin, .600179257-024
1cSocket, 40 Pin, .600179257-04017¢GAL16V8, 25 ns136085-1038,
12CSocket, 28 Pin, .600179257-028JEEPROM, 200 ns, 128K x 8136089-1049
18BIntegrated Circuit, 741874137023-001
12ESocket, 32 Pin, .600179257-03218CIntegrated Circuit, 7415138137177-001
15CSocket, 28 Pin, .600179257-028
15ESocket, 32 Pin, .600179257-03219BIntegrated Circuit, 7415393137146-001
17CSocket, 20 Pin, .300179259-02019Integrated Circuit, 741874137023-001
19EEPROM, 150 ns, 128K x 8136092-0081
17E, 19ESocket, 32 Pin, .600179257-03220BIntegrated Circuit, 7418393137146-001
20CSocket, 20 Pin, .300179259-02020CGAL16V8, 25 as136085-2046

Miscellaneous Hardware Capacitors

++1005V1 Test Point179051-001C1,C2Capacitor, 47 UF. SOV, Electrolytic — 123015-476
AGND1Test Point179051-001C3Capacitor, .1 pF, 50 V, +80%-20%,
GND1,GND2 Test Point179051-001Ceramic122002-104
—Nut/Washer Assy.177026-0036C4Capacitor, 10 WF, 25 V, Electrolytic124009-106
HS1Heat Sink, TDA2030178190-032C5-C7Capacitor, .1 LF, 50 V, +80%-20%,

Ceramic 122002-104 JaUD Connector, 36 Ckt, .1 Bottom Entry 179299-036

sWiSwitch, Slide, SPDT160040-001C8Capacitor, 10 UF, 25 V, Electrolytic124009-106
—Nut/Washer, Zinc177026-0036C9,C10Capacitor, .1 pF, 50 V, +80%-20%,
—Screw, Pan-Head, #6-32x3/8,Ceramic122002-104
Cross-Recessed, Cadmium72-1606SC13,Capacitor, 47 UF, SOV, Electrolytic123015-476
—Thermal Compound107031-001C14-C22Capacitor, .1 [1F, 50 V, +80%-20%,

Ceramic 122002-104 Integrated Circuits

1DIntegrated Circuit, Quad Op-Amp,C23Capacitor, 10 pF, 25 V, Electrolytic124009-106
M3403137673-001C24, C25Capacitor, .22 HF, 50 V, +10%, Ceramic 122015-224
2a,Integrated Circuit, TDA2030137301-001€26-C28Capacitor, .1 UF, 50 V, +80%-20%,
3DIntegrated Circuit, 40663137580-001Ceramic122002-104
4AIntegrated Circuit, TDA2030137301-001c29Capacitor, 1000 pF, 50 V, £10%, Ceramic 122015-102
4C,5CIntegrated Circuit, 4066B137580-00130-32Capacitor, .1 HF, 50 V, +80%-20%,
6D, 6FIntegrated Circuit, Quad Op-Amp,Ceramic122002-104
M3403,137673-001C33,Capacitor, 3300 pF, 50 V, +5%, NPO,
7cIntegrated Circuit, 74LS273137040-001+80%-20%122019-332
8AIntegrated Circuit, 74LS174137122-00134, C35Capacitor, .1 HF, 50 V, +80%-20%,

Ceramic 122002-104

8DIntegrated Circuit, YM3012137402-001C37Capacitor, 2200 pF, 50 V, +80%-10%,
9c1Integrated Circuit, YM2151137401-001Ceramic122015-222
10AIntegrated Circuit, 74LS273137040-001
11¢Integrated Circuit, 6502 A137577-001C38Capacitor, .1 WF, 50 ¥, +80%-20%,

Ceramic 122002-104

12EPROM, 200 ns, 64K x8136092-008039Capacitor, .015 pF, 100 V, 45%, Poly 126009-153
12EEPROM, 200 ns, 128K x 8136089-1051C40Capacitor, 10 uF, 25 V, Electrolytic124009-106
134,Integrated Circuit, 74L$240137251-001C41Capacitor, 1000 pF, 50 V, 10%, Ceramic 122015-102
144Integrated Circuit, 7415374137144-001

“C42, C43. Capacitor, 6800 pF, 50 V, 80%-10%,

15CIntegrated Circuit, RAM, 8K x 8, 100 ns, .6 137535-004Ceramic122015-682
15EEPROM, 200 ns, 128K x 8136089-1050
Page 44

CHAPTER 4 — PaRTS ILLUSTRATIONS “& GUARDIANS OF THE HOOD

JSA Ill PCB Assembly Parts List, Continued

Desig- Desig-

natorDescription.Part No.matorDescriptionPart No.
C44, C45.Capacitor, .1 HF, 50 V, +80%-20%,R37Resistor, 160 K Q, +5%, 1/8 W110027-164
Ceramic122002-104R38.Resistor, 10 K Q, 45%, 1/8 W130027-103

C46, C47 Capacitor, 1000 pF, 30 V, +10%, Ceramic 122015-102

C48, C49Capacitor, 3300 pF, 50 V, 45%, NPO 122019-332R40Resistor, 30 K Q, £5%, 1/8 W110027-303
R41Resistor, 15 K Q, 15%, 1/8 W110027-153
50Capacitor, 10 HF, 25 V, Electrolytic124009-106R42Resistor, 150 K Q, $5%, 1/8 W110027-154
C51-C54Capacitor, .1 UF, 50 V, +80%-20%,RB,Resistor, 7.5 K Q, 25%, 1/8 W110027-752

Ceramic 122002-104

R44Resistor, 15 K Q, 45%, 1/8 W110027-153,
DiodesR48Resistor, 3.3 K ©, £5%, 1/8 W110027-332
CR1, CR2Diode, 1N4001131048-001R49Resistor, 33 K 2, 5%, 1/8 W110027-333
CR3Diode, MV5053, Light-Emitting131027-002R50Resistor, 30 K Q, £5%, 1/8 W110027-303
CRG-CR8Diode, 1N4001131048-001
CRODiode, MV5053, Light-Emitting131027-002R51Resistor, 6.2 K Q, 35%, 1/8 W110027-622
R52, R53Resistor, 12 K Q, +5%, 1/38 W110027-123
ResistorsR54Resistor, 7.5 K Q, 25%, 1/8 W_110027-752
R1,R2 _ Resistor, 10 K Q, +5%, 1/8 W110027-103RSSResistor, 560 Q, +5%, 1/8 W110027-561
R3Resistor, 33 K Q, 25%, 1/8 W110027-333
R4Resistor, 1 Q, +5%, /8 W110027-010R56Resistor, 470 Q, +5%, 1/8 W110027-471
RSResistor, 33 K Q, +5%, 1/8 W110027-333RSTResistor, 100 Q, £5%, 1/8 W110027-101
R59Resistor, 10 2, +5%, 1/8 W110027-100
ROResistor, 470 Q, 5%, 1/8 W110027-471R62Resistor, 15 K Q, +5%, 1/8 W110027-153
R7Resistor, 33 K Q, 25%, 1/8 W110027-333
R8Resistor, 1 K Q, +5%, 1/8 W110027-102R63Resistor, 10 K Q, 5%, 1/8 W110027-103
ROResistor, 33 K Q, 45%, 1/8 W110027-333R64Resistor, 15 K Q, +5%, 1/8 W110027-153
ROSResistor, 7.5 K Q, 45%, 1/8 W110027-752
R10Resistor, 470 Q, +5%, 1/8 W110027-471ROGResistor, 10 K Q, +5%, 1/8 W110027-103
RILResistor, 1 K Q, +5%, 1/8 W110027-102
R12Resistor, 470 Q, +5%, 1/8 W110027-471RO7Resistor, 3.3 K Q, +5%, 1/8 W110027-332
R13Resistor, 1 K Q, +5%, 1/8 W110027-102ROBResistor, 6.8 K Q, +5%, 1/8 W110027-682
R69Resistor, 16 K Q, 45%, 1/8 W110027-163
R14Resistor, 470 Q, +5%, 1/8 W110027-471R70Resistor, 2 K Q, +5%, 1/8 W110027-202
R15Resistor, 1 K Q, $5%, 1/8 W110027-102
R16Resistor, 470 Q, +5%, 1/8 W110027-471R71Resistor, 6.8 K Q, +5%, 1/8 W110027-682
R17, R20Resistor, 1 K Q, +5%, /8 W110027-102R72Resistor, 10 K Q, +5%, 1/8 W110027-103
R73Resistor, 20 K Q, 25%, 1/8 W110027-203
R22Resistor, 470 Q, +5%, 1/8 W110027-471
R23Resistor, 33 K Q, +5%, 1/8 W110027-333
R24Resistor, 1 K Q, $5%, 1/8 W110027-102
R25,Resistor, 1 Q, +5%, 1/8 W110027-010
R26Resistor, 1.2 K Q, 45%, 1/8 W110027-122
R28BResistor, 10 2, +5%, 1/8 W110027-100
R29Resistor, 5.1 K Q, £5%, 1/8 W410027-512
R30Resistor, 15 K Q, £5%, 1/8 W110027-153
R31Resistor, 10 K Q, +5%, 1/8 W110027-103
R32Resistor, 620 K Q, +5%, 1/8 W110027-624
R33,Resistor, 330 K &, 25%, 1/8 W110027-334
R34Resistor, 82 K Q, +5%, 1/8 W110027-823
R35,Resistor, 20 K Q, +5%, 1/8 W110027-203
R36Resistor, 39 K Q, +5%, 1/8 W110027-393<>
Page 45

CHAPTER 5

Schematic Diagrams

INTRODUCTION

W. HIS CHAPTER contains the

schematic diagrams for the

Guardians of the "Hood™

game printed-circuit board and the

JSA Audio III PCB. In addition, this

chapter includes wiring diagrams for the entire game, the coin door, and the power supply, and the Hitron and Peter

Chou switching power supplies. The

game PCB and JSA Audio III PCB

assembly drawings are illustrated in

Chapter 4, Parts Illustrations.

Page 46

Cuapter 5 — ScHematic DiaGRams * GUARDIANS OF THE OOD.

awe (30> sated C2 000 ONO) yRrWA-2 0+ 00 (eB) aRewAa Os 0 (6802 JerrR-« oo oa

  • sarees Os 50 Cev) ewsi-@ O——— ney KEY AW? O- CCONTRL? Jeewni- 8 os TOTAL. CC-LOCKLD JaewA-§ O- CSPRRA* > Jarw-20. O————a spre CAUD* > Rem 31 O————+ pups CREO) lseman-12 O— + RED. BLUE) sawe13 O————» Lue Cv10 ¢x0) J@en-1¢ 0 vino CSELFTEST) lePMR-18 9—————« SeLrTEsT COIN.) sAReA-16 0 comm. CSTARTLD seewn-i7 O— + str CUPLAD Jeee-18 Oo uP COOMMLAD JeRwR15 02 ond CLEFTLAD Yaewe-70 0+ Lr CRIOHTLAD Jaren 21, 02 RT CLeurTonn > Je¥eN-22 O———a ACTA CLOUTTONE > JAw-23 o——— ecTEL CLBUTTONS > Yeeww-24 oO———s acre CLEFTLB) uewa-23 Ow eI CRIGHTLE srewA-76 O————e acTTR: COND) Jewn-27 Os caw ONO) Jernen28 Oe

ox cHeNo cowmecten AT (OND) Reem O————* OND GO) Jeea-B o———+ oo +802 Ieawec O——$+ +50 C5v) Jneee-0 02 50. C50) drew@-e 2 “50 coagv) yawn oO te CY IRPPRH OM CONTR? Jee J 0 TERT E-LOCRR) JAM O- CSPRRL=) JareR-L O———# Par AUO ONO) wm 0+ au0-00 CCREEN) JRewA-N O————+ GREEN (SYNC) Ipewn-P G+ COPPER (SERVICE) sRwA-R O————° FERUTCER COLT) Yeas Oe TILT CCOINR) JeeR-T 0———# COIN CSTRRTR) SpepA-U O———a SIRT: CUPRA) Jieniey o———a uPz CORMNRAD IReRR-H O———* Dn CUEPTRAD leew Oa Lr CRICHTRAD IpveR-¥ O———+ AT. (ROUTTONL? JAMR-7 Oe actrz CREUTTON2 > JFeR-RA O————+ ecTB2 CROUTONS > le¥PRi-B O———+ acicz (CLEFTRB) Je¥mB-CC 0+ aT RIGHTRED JeReA-09 0+ ac COND) JAPRLEE 0+ O60 (OD) deeR-TF OO

FINGERS OMY.

PL301Re, re) 25 0 —encTTRa ty ORT, 13 0 —eactc3 32 oe acres A o—ecta3 40 o—eRra Oo 0LF3 soem 7 o— aura 6 Oe stent 5 o—ecoIns ¥ oe services toe {oon

asc 1 Oe ngync.ouT 2 O— vstNc OUT 3 Oa VION oat

ws ; wo me ft

oe : a

a oe s3ya TSTPT_NS toe

ono Jono TSTPTNS pz cD} GND oP ow 9 L,

TSTPT NE

ax ot erat ofan oles som sis Soi oe Soi sam Fernie cate) O23 Ga) 3 Cane ot amiss ott canto) ont cnt?) pet eety ott care S22 caso) on osu Ce eebae oa w oem oibe ceimted cere) oan wr am

often COOMECTED AT PINS 38 AMO 60 ONLY.

Page 47

GUARDIANS OF THE ‘OOD % CHAPTER 5 — SCHEMATIC DIAGRAMS

coon. me FRG wou

a0 "

or

‘SERVICER

” coon Ome ae * OB as

seurtest s-rest we

as

Ra

coe

SPARE GATES

ome toto

PR an Pre "

et 420/238 ” ae

zoein an

Figure 5-1 Guardians of the ’hood Game PCB Assembly Schematic Diagram 049756-06 B

Page 48

CHAPTER 5 — SCHEMATIC DIAGRAMS % GUARDIANS GF THE "HOOD,

Ayo gave feos $ a5 ay Do Eng SmhERs wma tfe _ me [ime Heres we Lez te ; — oe etn res aE ah 1 019 if = ey 2 t ce] rate 4 xoit are Tt. a ap 1 4, a tSasT PRTR PUPA pa pee Te ome

“ Rol SRE SRST Re ROT RY g RUT 308 . wo wae mes = t Tee a St am =e Le won eine rc nr ez a ACTAL “Ree we zee al ‘STRTE: ik a7 Faby 4 xD ster = 1 K rae

L J" TT see

se " wig tomer |e a 315 Si} awe ity raped sabe ERASE VCR Bt sie Ser Thame as 43 3 2Scux elf ar 33 Posi reve a1 Sot ree awe Ea gat nee 3 Hf thao sv = occ pois xs Por cap HE? p08 Fertites aE oes arf fee k sede Rage oid es e9.R021 ar) tpt fies Stee | fGen Ee | ™ ese ee " , 68.08 need R20, 6OC 13s whe 2" a ao = im a ai x07 13, i ie al amma SS oe ie fe Ee wets ew uD Ss shi testis mc = eee sereve—iiye ay 1 te rot meee aoo ‘sete —Sfe6 110s ae meer ie sooner

  • 4/R o—_—_ Cad
Page 49

GUARDIANS OF THE "OOD @ CHAPTER 5 — SCHEMATIC DIAGRAMS

xoro:151

ao Baro sre F470 oee—_18f6

senvice3)rn be3\u8
i]aBin
8=aeHe

TTL a

atte)=Slimor
acrTRSHe3415
Raioharray]

To TT" Tes

BonGaaweas
pic}iorier
ait;“*s
“onsrTzo
aeFiaah
STARTS:{PLR aroaK232
LtaLETT
|7axe

ooo

Figure 5-1 Guardians of the >hood Game PCB Assembly Schematic Diagram 049756-06 B

5-5

Page 50

CHAPTER 5 — SCHEMATIC DIAGRAMS % G¥ARDIANS OF THE

Fa : owe is reo nese cir} te 1 7 See ahs = {ie iaaye = SEE isye 3h H 000 ne? “he fqut —ine os cae 5 ¢ 330 ia Xoo | erera ~

aus

cane Tie Wa 32s LUE

= i ‘i Pesuseess Le vince

| __ensywc.our

CPST

ustnc.0UT

cz tear bes ‘10°F yt" Sorr cen vneo.

Figure 5-1 Guardians of the ‘hood Game PCB Assembiy Schematic Diagram 049756-06 B

5-6

Page 51

GUARDIANS OF THE "HOOD % CHAPTER 5 — SCHEMATIC DIAGRAMS

me Tm earn

‘Ft 20/250SDITuaw

PVT fe Tea mr

goerZe nov"‘sox|eo19

1W Oty = T 40ov r i} i [ 0s]

is0DF15
t.icaf ow
;ovga4
7HEa82sua

'

ciai“120A
soeHoe

any f 1 C20 H “= 10000

@!By

: H = 1

' f H f vA H H > A 88 4 H

Be:Z
arefaon
‘awH8

H

Figure 5-2 Hitron 5V, 7A Switching Power Supply (HSA-130) Schematic Diagram 149014-001

a a on weinv sw Pezos Val = Cer seat 002007 fHoK/SW wl le fre Y ar fo 1007200V < 100K.5W oh

DevtNat48, crova7ipRniky Reairopvi2W

Figure 5-3 Peter Chou Power Supply Schematic Diagram (optional) F102141288

Page 52

Cuarrer 5 — SCHEMATIC DIAGRAMS & GUAKDIANS OF TIE "HOOD.

[18 spr atv HS oe He os ioe seat

+ $02 Ts Soe et oe ise

ova

w = ow

rt) “47 ‘aypass Tyo cy

= oetee

mm WG HOLE, aa WG HOLE, aa WG HOLE, oe = TG Oe cores

BND AND AGND TIED INTERNALLY NEAR MSM6295

5-8

Page 53

GUARDIANS OF THE ‘HOOD “ CHAPTER 5 — SCHEMATIC DIAGRAMS

sre *5| a role

ees | SB!beo—2fsoSaL42 —S oe
Sotoop’apbettetop}ems
feo]safe—s0etofSoS — ste
cielo[3tie—tfeeofesos
soei319oeoiasot

Tr Tere

ou

rim (primera. eee

rise roe. rene

ne Grime. vem

Figure 5-4 JSA Audio Ill PCB Assembly Schematic Diagram 048973-01 C

Page 54

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 55

GUARDIANS OF ‘THE “HOOD CHAPTER 5 — SCHEMATIC DIAGRAMS:

serie] te 1706 He rest seats 170s Se

sor [so adhe wis sooedZj7> rope aur soseitje 6a core soeee}s0 © saptE—s octe: spelen do} 2 —= oreo sbee—]4 90 ao} f—- ORTRES. sore—fep ops — exe soe so} TEE SX aa] veers or ups west

ansve——2bax opt

figure 5-4 JSA Audio Il] PCB Assembly Schematic Diagram 048973-01 C

5-11

Page 56

CHarTeR 5 — SCHEMATIC DIAGRAMS“ GUARDIANS OF THE ‘HOOD

“ Lnsens)

oo ee ee ‘ Tex ze F aan ols

Sui x, z rn i rn sHe + Eu

reas | Madde eseRszazs

ied

exo} socket

5-12

Page 57

GUARDIANS OF THE "HOOD CHAPTER 5 — SCHEMATIC DIAGRAMS

Figure 5-4 JSA Audio Ill PCB Assembly Schematic Diagram 048973-01 C

5-13

Page 58

(CHAPTER 5 — SCHEMATIC DiAGRAMS @ GUARDIANS OF THE “HOOD

7 po 7 sex + [10 BY au st sR = [L betel

seane [17% up {18 {WAX

ust 5 |20b% ricer 1 | op WC stronaxick 1 |22} #28 = rastpuncH 1 [23/0 sTRoNGPUNCH 1 |24b We rasTIKick 1 2s STARTIDEFENO 1 [2a] ov | Lea sw on |27 spare | u w2ly pow 2 |w eT 2 |x wout 2 |y sTRonGKick 2 |Z FASTPUNCH 2 | a STRONGPUNCH 2 |b FASTKICK = 2 |S STARTIDEFEND 2 | d +8v [4 swonp | a

+ é < Mano >OUuTNe

5-14

Page 59

GUARDIANS OF THE ‘loop “ CHAPTER 5 — SCHEMATIC DIAGRAMS

LEFTIPLAYER 1

8848 Rk BKB TeTrrre

S10 START/DEFEND [PLAYER 2 up pow LEFT mone STRONGKICK#! FASUPUNCH ‘STRONG/PUNCH FasTKicK "| STARTIDEFEND | Hagewveasun—

RIGHT PLAYER

_CONTROL_PANEL J

Figure 5-5 Game Main Wiring Diagram 050191-01 A

5-15

Page 60

(CHAPTER 5 ~ SCHEMATIC DIAGRAMS GUARDIANS OF TUE ‘OOD.

‘SW GND RIGHT COIN SW LEFT COIN SW RIGHT LOCKOUT COIL LEFT LOCKOUT COIL +10V DC 6.3V DC 6.3V DC CHASSIS GND oR. Right Coin Switch on, ox]

Diode V 1Na007 (2 places) w, | Right Lockout Coil

+01 ONLY Coorg Haseno

Figure 5-6 Over/Under Coin Door Wiring Diagram A037542-XX F

(BN FI BN. p> BK W160) FILTER |__pu

FL

Tet)

t20V AC BNW H wicom,

COM BU 1 BK (120V) NEUTRAL UNE

| +5V/-SV/412V | SWITCHING ‘SUPPLY

Figure 5-7 JAMMA Power Supply Wiring Diagram

5-16 049289-01 A

Page 61

M. Guardians of the Hood" Game Statistics Sheet ATARI GAMES

Location: Date Recorded:

Meter:

Left Coins: Right Coins: Auxiliary Coins: 0 Player Mins: 1 Player Mins: 2 Player Mins: nn Sessions: New Games: Continued Games: New (Game) Mins: Cont'd (Game) Mins: Error Count: Total Credits: Avg Time/Credit: Average Time/New Game: Average Time/Cont'd Game: Hl

Statistics 2: Round Counts and Average Times

Intro Gym 1 Alley Movie Gym 2 Station Subway Train Gym 3 China Street Bar Gym 4 Boardwalk Funhouse Unused ORs eeeeeeeeee

Unused New Game Time in Seconds

0-39 40-59 60-79 80-99 100-119 120-139 140-159 160-179 180-199 200-219 220-239 240-259 260-279 280-299 300-319 320-339 340-359 360-379 380-399 400 & up Median MATTE Continuation Game Time in Seconds

0-39 4059 60-79 80-99 100-119 120-139 140-159 160-179 180-199 200-219 220-239 240-259 260-279 280-299 300-319 320-339 340-359 360-379 380-399 400 & up Median ATPL

Continued on back page

Page 62

Guardians of the “Hood” Game ATARI = Statistics Sheet, Continued

Location: Date Recorded:

Meter:

Session Time in Minutes

0-2

6-8 9-11 12-14 15-17 18-20 21-23 24.26 27-29 30-32 33-35 37-38 39-41 A244 45-47 48-50 51-53 5457 57 & up MEAP Median Segment at Which Player Quit

0 —_ 1 —___ 2 a 3 —_—_

6 —_— 7 a

9 ——_ 10 _ ll —

B 14+ Median Who's the most popular — Wave 1 Conner Chief Javier Tanya HI

Who's the most popular — Wave 2 Conner Chief Javier Tanya Jay-Jay

Who's the most popular — Wave 3 Conner Chief Javier Tanya Jay-Jay Boris HT

Who's the most popular — Wave 4 Conner Chief Javier Tanya Jay-Jay Boris Kwan HTT

Page 63

[a] ele ele eee eel eel eel eel ele ele

~ Seller warrants that its printed-citcuit boards and parts theteon:are free from

” :defects in material and workmanship under normal use and.service for a

period of ninety (90) days from date -of shipment. Seller ‘warrants: that its.”

“. video, displays and laser-video disc-players (in games supplied with displays

and video-disc. players) are free from defects in material and workmanship:

“under normal use-and service for a period: of thirty (30) days from’ date of

shipment.’ None of the Seller's other products or parts | thereof-are warranted. : Pk the products. described in. this manual fail to conform to. this warranty; “. Seller's sole liability shall be, at its option, to repair, replace, or credit Buyers account for such products which are yemened to Seller’ oe casa wai-° ranty period, provided: “

3 Seller is promptly. notified in witing upon discovery by Buyer that

oo . $aid, products are defective, .. (b) Such products are returned prepaid to Seller's plant; ain ‘(c) - Seller’s examination ‘of’ said products discloses to Seller's satisfaction that-such alleged defects ‘existed and were not caused by accident, o “misuse, neglect, ‘alteration, iPFODEL eae installation, or x improper testing. ” : ; In:no event shall: Seller be liable ti loss of profits, loss of use;: , incidental 0 or consequential damages. 2 Except for any express warranty Set forth ina written contract 2 ehigenys Sell- i . er and Buyer which contract.supersedes the terms herein, this warranty. is s expressed in lieu of all other warranties: expressed or implied, including the implied warranties. of merchantability and fitness for'a particular purpose, ~ » / and of all other obligations or liabilities on the Seller's part, and it neither assumes nor.authorizes any. other person to assume for the Seller any other liabilities-in connection: ee the sale of Discogs by Seller. : Es SOS

3 SERGE WESEEREEEEREUERSEROCAREERE al

“The-use of any non-Atari parts may.void your. warranty, according to the terms of the warranty, The use of any non-Atari parts-may’ also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non- ee lied compenents with our games, in order to ensure your safety. . : Atari distéibutors are independent, being privately owned and. operated. In a judg- ~ merit they may sell parts or accessories other than Atari parts or accessories. Atari Games ’ Corporation’ cannot be responsible for the quality, suitability or safety of any: non-Atari part or any modification including: labor which is performed by such distributor. . - :

Page 64

ATARI

GAMES.

ATARI GAMES CORPORATION

675 Sycamore Drive Milpitas, CA.95035-