TenPin Operating Instructions and Service Manual
Tenpin (Gremlin Industries, Incorporated) · Manual · 69 pages · 18 sections · original scan
TENPIN
an ELECTRONIC WALL GAME BY
GREMLIN INDUSTRIES, INCORPORATED
8401 Aero Drive
San Diego, California 92123
OPERATING INSTRUCTIONS
and
SERVICE MANUAL
TABLE OF CONTENTS
INTRODUCTION-------------~------------
UNPACKING & INSPECTION---------------~
INSTALLATION & CARE-------~-~---------
TENPIN GAME DESCRIPTION--------~------
PROGRAMMING & ADJUSTMENTS-
LAYOUT DIAGRAM------------------------
SYSTEM DESCRIPTION--------------------
BLOCK DIAGRAM-~--~~-~~-~-=-------~---------- Page 11
DETAILED CIRCUIT DESCRIPTION---------- Page 12
RECOMMENDED SPARE PARTS--~--~---------~- Page 18
PARTS LISTS & SCHEMATICS---~---------- Following Pages
INTRODUCTION
TENPIN is an electronic game that makes extensive use of digital integrated circuits. This manual assumes that the maintenance technician possesses a general knowledge of solid-state circuitry and TTL digital integrated circuits. Any individual not knowledgeable in this area should not attempt to repair the electronic portions of the game. IT SHOULD BE NOTED THAT ANY ATTEMPT TO REPAIR THE GAME IN THE FIELD WITHOUT THE EXPRESS CONSENT OF THE FACTORY WILL IMMEDIATELY VOID THE WARRANTY!
NEVER replace any component with anything other than an EXACT replacement part. This includes LAMPS, TRANSIS- TORS, INTEGRATED CIRCUITS, and the like.
LAMPS used in this game are #1813, which operate at 14.4 volts, 100 ma. and #756 lamps which operate at 14.4 volts, 80 ma. NEVER use a lamp that operates at a lower voltage or higher current. To do so will very likely damage the circuitry in the game.
DO NOT use metal objects (screwdrivers, pliers, etc.) around the lamp sockets with the game turned "ON". The outer shell of the sockets have voltage on them, and shorting them to each other or to other points on the game will damage the circuitry.
DO NOT replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a larger value can cause severe damage to internal components if an overload occurs.
ALWAYS consult the manual before attempting any repairs.
CORRESPONDENCE regarding this game should be addressed to:
GREMLIN INDUSTRIES, INCORPORATED 8401 Aero Drive San Diego, California 92123
Phone: 714-277-8700
UNPACKING AND INSPECTION:
The TENPIN Game is normally shipped in a single package containing the game main frame and the accessory kit, which consists of the coin box, transmitter and associated parts.
The box must be opened immediately upon arrival and inspected for freight damage. It is advisable to connect the game for operation and determine that it is operating properly, as some freight damage can occur within the main frame and not be immediately evident. during a cursory visual inspection.
If damage has occurred during shipment, the recipient should immediately file a damage claim with the carrier. Filing a claim will protect the recipient from bearing the full cost of any repairs that may arise from the damage.
Any game or accessory claimed to be defective must be returned to GREMLIN INDUSTRIES, INC., 8401 Aero Drive, San Diego, California 92123, transportation charges prepaid. The game will be repaired and returned to the customer, transportation charges prepaid, if still within the warranty period. If the game is found to be damaged by misuse, improper attempts at repair, or abuse, it will be returned to the customer with transportation and repair charges billed.
In the instance of a defect of sub-assemblies or assemblies manufactured by other than GREMLIN INDUSTRIES, every effort will be made to assist the customer in obtaining satisfaction from the original manufacturer.
INSTALLATION PROCEDURE
1.) The game is designed to be supported from two points by either hooks or chains (Refer to FIGURE l. ).
EITHER
Two (2) HOOKS OR
Two (2) CHAINS
FIGURE 1
2.) The coinbox can be mounted in any convenient location and is connected to the game by means of the 10-pin molex connector provided.
After mounting the coinbox (insuring the cable will reach the game), connect the coinbox as follows:
- Open front screen of game.
- Connect game as illustrated in FIGURE 2.
FEED THRU INTERNAL ™“ | COINBOX CONNECTOR} TO COINBOX
FIGURE 2
MAINTENANCE
The following are recommendations for the care of your GREMLIN wall game. These recommendations are of a nontechnical nature. For technical information refer to other sections of this manual.
1.)
2.)
3.) CLEANING
GREMLIN recommends using an all purpose commerical cleaner such as 409 (or equivalent) for all exterior surfaces.
LAMP REPLACEMENT
Lamps should only be replaced with exact replacements. TENPIN uses #756 and #1813 lamps (12-14 volts, 100 ma), any attempt to use lamps other than ones specified could cause electrical damage and void the game warranty.
LOGIC BOARD REPLACEMENT
If, for any reason, the logic or sound board in your game needs to be replaced the same rule applies as for lamp replacement: ALWAYS REMOVE POWER from the game!
TENPIN GAME DESCRIPTION
The TENPIN game is a single, wall-mounted unit that needs only an external coinbox and transmitter (control box) to operate. Both of the latter units are supplied with the game.
Within the main frame of the game assembly is a large (2.5 feet by 5.0 feet) printed circuit lamp board, which contains plug-in provisions for the power/sound board and the logic board. Additionally, a receiver module is incorporated on the front of the lamp board to receive and process the signals transmitted from the hand-held transmitter control.
The transmitter/controller is a standard, tone-modulated 49 MHZ transmitter. The only control necessary for its operation is the top-mounted push button that is actuated to play the game.
The coinbox provided with the game is a quarter acceptor type that causes a switch contact closure with each coin inserted. Each coin activates the circuitry in the main frame and allows a game to be played.
The game is played in the following manner:
1.) Two players normally compete in TENPIN, each taking turns at the control box that enables them to play from any place in the room. An option is incorporated to allow single player games.
2.) A coin is deposited and the game activates, allowing the transmitter control box to initiate action.
3.) A triangle indicator moving back and forth across the alley represents 15 possible ball paths which determine the number of pins knocked down on each ball roll. The first player depresses the control button, which stops the movement of the triangle and initiates the ball roll. Depending on how skillfully the player selects the ball path on the first ball, the player may be awarded a strike (20 points; one point per pin plus a 10 point bonus) or a gutter ball (zero points) or anywhere from one to nine points (one point per pin). If the player does not get a strike on the first ball, a second ball is awarded and "Roll Again" will light up. The player can then try to knock down the remaining pins. If the player is successful, he will be awarded a spare (15 points; one point per pin plus a 5 point bonus). Points are awarded for pins knocked down and any pins left standing after the second ball will not score points.
4.)
5.)
6.)
7.) When the ball is rolled a realistic sound of the ball rolling down the alley and hitting the pins is generated. If the ball fails to knock down any pins, a frog croak is generated. When a strike is rolled there is a sharp clap of thunder, Rip awakens, and the bowler is saluted by the merrymakers.
A free game is awarded when a preselected score is attained or exceeded by either player during the period of a game. This score is selected by a switch on the front of the lamp board.
TENPIN is internally programmable to allow control over the speed of the triangle sequencing and the ball roll.
The length of the game is controlled by the number of frames to be played and is selected by a rotary switch on the front of the lamp board. The switch is accessed by opening the front display panel.
TENPIN GAME PROGRAMMING AND ADJUSTMENTS
LOGIC BOARD
There are two program adjustments and two speed adjustments
on the TENPIN Logic Board, P/N 812-0001. They are:
1. THE NUMBER OF COINS NECESSARY FOR A GAME CREDIT.
For single coin credits a jumper wire must connect Pins El
and E3 (this is the factory setting). If two coins for a
game credit is desired then the jumper shculd connect Pins
El and E2. Only one jumper should be in place at a time.
THE NUMBER OF PLAYERS PER CREDIT.
For single player per credit a jumper wire must connect
Pins E4 and E5 (in this configuration one credit gives a
single player game and two credits give a two player game).
For two players per credit a jumper wire must connect
Pins £4 and E6 (this is the factory setting and in this
configuration no single player game is possible). Only
one jumper should be in place at a time.
TRIANGLE SPEED ADJUSTMENT.
The triangle speed adjustment is potentiometer R6 and it
controls the speed at which the triangle ball path indicators
oscillate back and forth across the alley. Speeding up the
triangles makes it more difficult to pick the optimum path
and therefore makes the game more difficult to play. Slow-
ing down the triangles makes the game easier.
TENPIN GAME PROGRAMMING AND ADJUSTMENTS (Continued)
LOGIC BOARD (Cont'd.)
4.
LAMP MASTER CLOCK ADJUSTMENT.
The master clock adjustment controls most of the timing/
counting functions of the game, such as the ball roll
speed, but does not change the length or difficulty of
the game. This potentiometer Rl is factory set and does
not require adjustment under normal circumstances.
BOARD
from
1. There are two game program adjustments that are accessible
the front of the lamp board and they are:
“END OF GAME FRAME" SWITCH.
This four position switch selects the last frame for the
end of the game. It selects either 10, 9, 8, or 7 frames
per game.
THE “FREE GAME FOR" SWITCH.
This eight position switch selects the minimum number of
points at least one player must have to be awarded a free
game. It selects scores of 130 points thru 190 points.
=9-
FAN HANGERS FRAME LAMP
RECEIVER
(FRONT OF BOARD)
SPEAKER
FREE GAME SELECT
SWITCH (FRONT. ADIUST) END OF GAME FRAME SELELT SWITCH may) (FRONT ADIUS
= COINBOX CONNECTOR
+4 VDC REGULATOR. ADJUST TILANSFORMER T2 3 GNODUCTOR LINE CORD
FIGURE 3 LAYOUT DIAGRAM (REAR VIEW OF GAME)
SYSTEM DESCRIPTION
TENPIN is a digitally controlled, sequentially animated game. Digital integrated circuits control the rate, interval, and sequence of events.
Figure 4 is a simplified block diagram of the game. The Credit is applied to the End of Game circuit when a valid coin drop is received by the Coin Discriminator which activates the Triangle Motion/Selector and allows it to begin cycling.
The Receiver output will now stop the cycling of the Triangle Motion/Selector circuit and select a ball path dependent upon the triangle(s) which were lit when the transmitter pushbutton was depressed.
The Triangle Motion/Selector starts the Ball Motion circuit, which rolls the ball down the alley, and inputs to the Pin Proms, which select pins knocked down, and the Score Proms, which add up proper scoring and display it. The Score Proms output to the proper player (lst Up or 2nd Up). The End of Game circuit keeps track of the number of ball rolls.
The lst Up Score and 2nd Up Score are applied to the Free Game Selector and if either score is high enough to equal or exceed the score selected by the “FREE GAME FOR" switch, a Free Game is awarded and inhibits the End of Game circuit from inactivating the Triangle Motion/Selector, but does reset Frame Counter, lst Up Score and 2nd Up Score to zero.
The End of Game Selector is activated when the Frame Counter reaches the number selected by the "END OF GAME" switch. The End of Game circuit receives this signal and resets the entire game to zero and awaits another coin drop.
The Power on Delay circuit resets the End of Game logic on initial plug in of the game power cord. This is necessary to clear all of the logic to its zero state.
~-10-
_TENPIN SIMPLIFIED BLOCK DIAGRAM
foe MOTION
END OF GAME SELECTOR
FREE | GAME FRAME COUNTER TRIANGLE MOTION/ SELECTOR RECEIVER
SELECTOR
FIGURE 4
TENPIN SOUND EFFECTS AND POWER CONTROL
The sound effects developed for TENPIN are unique and
contribute to the life-like action of the game. The four
basic sounds and power buss control are described below.
For the following discussion refer to the Power/Sound
Board Schematic.
PIN & PIN BACKGROUND SOUNDS
The Strike and Hit sounds are very similar; the basic
difference being that the Strike sound is 800 ms long and
the Hit sound is 500 ms long.
When a Strike occurs a High is applied to pins 22 and
25 of the Power/Sound Board. When a Hit occurs a High is
applied to pin 22 only. As a result, a High of appropriate
length appears at pin 3 of U2.
This one-shot action causes the following: First, the
leading edge at pin 3 is coupled to Q4 and C6 thus quickly
charging C7. The voltage on C7 decays slowly and amplitude
modulates the 200Hz noise at the base of Q16. An amplified
version then appears at pin 8 of U7 and is summed into the
audio output by R138, supplying background noise for the
pins falling. Next, the logic High from U2 enables the
escillator of U10. When the oscillator output is High, 034
and Q31 are turned on and C46 begins to charge. When the
output goes Low, Q32 is turned on and C46 begins to discharge.
The resulting waveform is buffered by Q33 and applied to the
frequency modulation pins of oscillators U12, U13, and U14.
The frequency of each oscillator is vastly different.
This fact coupled with the frequency modulation applied to
the oscillators serves to create a psuedo-random event
generator that has the cadence of bowling pins falling.
Both the leading and trailing edges of the oscillator
outputs are capacitively coupled and appear at R150 and R158.
R150 is the input to a three stage resonant filter that has
a Q of 100 and a resonant frequency of 1200 Hz. R158 is the
input to a single stage resonant filter with a Q of 10 anda
resonant frequency of 200 Hz.
Noise with a cut-off frequency of 1200 Hz is applied to
the base of Q25 and modulated by the sawtooth appearing at
the base of Q24. The resulting modulated noise is injected
into the 200 Hz resonant filter at R157.
When a resonant filter receives an impulse, it tends to
oscillate at its resonant frequency. The sharp rise and decay
of those oscillations, plus the noise applied to the 200 Hz
filter, reproduce the familiar wood sound of bowling pins
falling. The oscillations from the two filters are summed
through R162 and R164 at the summing amplifier of U6 and
summed into the final audio at R142.
BALL ROLL
The Ball Roll is reproduced by applying 200 Hz noise to
the base of the amplifier 910. Q10 is gated on and off with
Qll. A Low from the Logic Board at pin 23 turns Q10 on. A
High turns it off. R36 and R37 provide Q10 with the correct
d.c. bias. R38 and R39 set the amplifiers gain to unity. The
Ball Roll is summed with the rest of the audio through R139.
FROG CROAK
Whenever a player bowls either a Miss or a Gutter, the
Frog croaks the player's misfortune.
A Low at pin 24 of the Sound Board is inverted by Q9 and
applied to pin 10 of U4. Pin 9 of U4 produces an oscillation
which is High for 50 ms and Low for 200 ms. When pin 9 of U4
is High it enables the oscillator at pin 4 of U4. Thus, pin 5
of U4 oscillates with a frequency of about 20 Hz. R24 couples
these oscillations to the resonant filter of U7, R51, R52,
C27 and C28.
The FET at pin 13 of U7 shifts the frequency response of
the filter. When pin 9 of U4 goes High, C26 is quickly charged
and the FET turns on. As the voltage at C26 decays, the FET
gradually turns off and lowers the resonant frequency of the
resonant filter. The Frog Croak is summed with the rest of the
audio through R140.
THUNDER
The Thunder occurs during a strike and is initiated by
a High going pulse at pin 21 of the Sound Board.
The Thunder sound is created by applying very low fre-
quency noise to the base of Q29 and modulating it with a
slowly decaying exponential voltage applied to the base of
Q30. An amplified version of the signal appears at pin 1
of U5 and is summed with the rest of the audio through R141.
POWER BUSSES
In order to cut the parts count and make the game more
reliable, a buss switching system is used in TENPIN. When a
game is initiated a logic High is applied to pin 40 of the
Sound Board. This applies power to one side of the Pins uP
lamps. The individual lamps are lighted by grounding the other
side of the lamps through a transistor.
The three Ball Path busses have power applied to them by
the Triangle sequence. When the Triangle sequence is at the
top, Ball Path Buss A is enabled (a High is applied to Pin 38
of the Sound Board), when it is near the middle, Buss B is
enabled, etc.
As the Ball Path is sequenced, triplets of lamps are
grounded through a single transistor but only one lamp is
lighted because only one Ball Path power buss is enabled at any
given time.
GENERAL ILLUMINATION DIMMING
When a game is not in progress the Logic Board sends a
logic High to pin 1 of the Sound Board. This grounds the
anode of Dl through Q7. Q1 on the Lamp Board is robbed of
its gate bias and turns off.
As the rectified a.c. at pins 5 and 6 begins to rise,
Cl charges through R4. When the voltage on Cl exceeds 5V Q2
and Q3 conduct and supply gate current to Ql. Ql then con-
ducts until the voltage at Cl drops below 5V. The effect is
to drop the rectified a.c. lamp voltage and dim the General
Illumination lamps thus saving power and extending lamp life.
AUDIO AMP
The Audio Amplifier used in TENPIN is of the quasi-
complimentary type. R88, D8 and R92, D9 provide provide voltage
biasing in order to prevent cross over distortion. Q19 and
Q20 drive the two TIP 29s which are capable of delivering 10
watts to a 16 ohm load. R86 and R84 set the mid-frequency gain
to 1l while C51 gradually rolls the gain off at high frequencies.
C55 rolls off the low frequency gain and R87 insures that the
amplifier output is always zero when no signal is applied to
the input. The summing amplifier of U6 sums all of the audio
inputs while C69 blocks and d.c. component of the summed signal.
The volume control (Lamp Board R3) is externally located
in order to accommodate any ambient noise level. The summed
audio output appears at pin 11 of the Sound Board and is
electrically connected to the volume control through the lamp
board. The attenuated audio returns to pin 12 of the Sound
Board (again via the Lamp Board) and is amplified for output
to the two series connected loudspeakers.
RECOMMENDED SPARE PARTS FOR TENPIN
ITEM
CAPACITOR
RECEIVER
COIN COUNTER
COIL
CRYSTALS
INTEGRATED CIRCUIT
LAMPS
DIODES
TRANSISTORS
TRANSFORMERS
LOGIC BOARD
PWR/SND BOARD
TRANSMITTER (Per 10 Units)
DESCRIPTION
Cap, C, Var 6/25pf
K-93
Digital
Coin Lockout
T/P Xmtr 49.830 T/P Revr 49.375
NE 555 7490 7474 74193 7400 7448 7404 Prom T/P U8 Prom T/P U9 Prom T/P U10 Prom T/P Ull
Socket #756 #1813
1N4002 MR751 MR501 1N914/1N4148
2N4403 SCR 2N5060 PE8050 SCR MCR106~-1 2N4401 TIP 29 SCR 2N6400
Game T-1 Game T-2
Assy, T/P Logic Bd
Assy, T/P Pwr/Snd Bd
Assy, XMTR, T/P PART NO. QUANTITY
154-9001 1
190-9010 1
220-9008 1
220-9061 1
230-9010 2 230-9011 1
314-9001 1 314-9003 1 314-9006 2 314-9007 1 314-9009 1 314-9013 2 314-9015 2 316-9044 1 316-9045 1 316-9046 1 316-9047 1
390-9002 5 390-9004 50 390-9005 150
481-9001 2 481-9002 2 481-9004 2 481-9006 2
482-9006 2 482-9009 4 482-9010 2 482-9012 2 482-9014 10 482-9016 2 482-9024 2
560-9110 1 560-9111 1
812-9001 1
812-9002 1
812-9007 2
TENPIN LOGIC BOARD SCHEMATIC
ABBREVIATION-DEFINITION LIST
ABBREVIATION
ADV
ASE
AVS
BMC
cpc
CNA
EOG
FRL
GSE
LBD
PLR
POD
PA ff THRU 7
BEOG
1P/2P DEFINITION
ADVERTISE MODE
ADVERTISE SEQUENCE ENABLE
ADVERTISE START
BALL MOTION CLOCK
CREDIT DOWN COUNT
CREDIT NOT ADVERTISE
END OF GAME
FRAME ONE
GAME START ENABLE
LAST BALL DELAY
PROM LATCH RESET
POWER ON DELAY
PROM ADDRESS § THRU 7
BUFFERED END OF GAME
ONE PLAYER/TWO PLAYER
TITLE ASSY TENPIN LOGIC BOARD
RELEASED prawn LIP TAK,L.J. - ‘DESIGN CHECK Fi AUTH | REVISION DESCRIPTION DRAFT
OCT 13 1977 1
++ —t * omen 5 a a ne Oe Oe Se
!
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ooo 060005 i 31 BE8CCCR0O0
2° hoe}
Wan = Ss WZ SF Hay
———S LPS SERS G8 = ~SS
= WA
i? =a SSA? —_ 2 EG ESPRIN
SS (re :
WSEAS a Ze, eS e ENS ~<Ss = 00000s0sedpoooocesed
~A\CiAPLCs)
R?
ard f@ M. sec TRIANGLE esas
FLASH (ST 2)
TS Io Ga POWER Buss & ROLL ASAIN W210 POWER/sw0 HF
| fe e | eS | POWER, |
| | (7406, | XPBUSS A | Tox |
é Os -. TAS we nese pe a a sebna? |, PS, eyes 4 L
| x i | a | D2 | Ayr | cc | |||
| (acK* | inpicaton, @MS5 | A | rrr | x | as | +a | OWER BUSS |
ou & Bus naaor mn A 7TP2 GAME RESET
960. BNSe0,
Bow | BALL POSITION. mead gee
MASTER, kana SHTzsa
CREDIT Gur 3)
SCHEMATIC TENPIN PITT ldo) LOG/C BOARD APPD.
REC,
Z. CAPACITANCE VALUES ARE IN M/CROFARADS ; RESISTANCE VALUES ARE/N OHMS Ble -900]
NOTES: unress oTHERWISE SPECIFIED oe
REVISIONS, DESCRIPTION
(> BLANK
42-45 Ik: yoout T soout 46-49 ¥ TP + PS rere PINS DOWN [68m om Ppa 88 a4, 2N5060 WAKING | aIP ‘STI ENS
£06 (sar ig 3) az 2Ms060 pac d SLEEPING RIP ery GuAsSES. ON yaace a2,
2w44o! LIGHTS (TO SWE PLCS) Bod 7 as micaio6 STRIKE te: jee . (aura) LIGHTHING
/
85K
aioe MCR IDE
MASTER, cUoew (HT 3)
Leap
_ TED. (su7ay
caer eat, A $ v2 STRIKE (58143) ——F os, (To SND. ao) hoe
stKprs, Gers}
POINTS (sur)
SCHEMATIC TENPIN LOGIC BOARD
MASTER baat HTD : OE TERT WBS RO €12-0001 SEE NOTES SHEET | NOTES: uncess orHeRwise SPECIFIED
2 1
NOTES: oncess ormenwise specie ee REVISIONS
| 1 | Tone [OR | DESCRIPTION |
] x [RELEASE
u +
| af | ax | on |
iz |ha90 ye 22 ____aHEGeo D elite) pee) rekk
| + | para | Seo |
| = | ‘ | FRAME |
i __| | 27
| rare | wv | | a | Bee | |
| nie | Loy“ retaver | Re, | peas | 3 |
| “aby | g | —; | cH! | |
| |__6 3 ans SH) | SB | ae | sur | |
| —_ | ace | wl? | NS] | 38g |
| wrt | sure) | Fx | ontop |
4 Tease
L s var
3 ef 2 ais sw) | ct
woh, gle Powe:
| | | M8 | ¢ | 9, | ne | (ees) |
ye ree 2 $84} _ av?
| panes | . | ayn | aay |
(Ses
re
| G57 | aa | =H | — |
| aoa’ | 295060 | 1 | |
| - ae | nN | Ri | Z |
| cis Sh | | | . | 8 |
| TEE) | “eye | (a6 | |
| PLS) | 4004/2. teurz) | Lod. v415 | |
| rn | 2, | ’ |
res 7
| Ave. | 3yx GP 43g s]7a29) | £ (040) | urs, | |
| sey | {sur 3) | eu 4 | ae | 434g} 5 |
| 06} 2 | 2 | 7404 |
& 10. iv 8 (aot, 4 1400} 2
eA
| ONE'S, | iH | | |
. STRIKE ers. ou out 2)
| 8 | - | 7 2 | FREE | 4 |
| —_ | AME TTP TTT TI | PN |
| cm 7at3 BoD wl, ale Peer Lee OFF je 9
| Ist UP | fe | 2 |
aso. { Bu Pa0% mas
GAme ENDS ar FRAME bNUMBER
| ; | qao4 | oK |
| TENS © | Pte | hes) |
TEAM oe oeSeernon TSeoke a rane See) PaaS L__. Gremiin industries, inc. Sum Binge, Catttor nin OREN
| vs? | TEAM | 7 | A |
| >. | RES, | Seo | SCHEMATIC TENPIN |
aa Thee LOGIC BOARD
xEAme BEE SSO TERT WO DRANG WO EY
| 3, - | TEAM | TEN PIN | 2 | BOC |
| | SEE NOTES SHEETI | 2 | Sle-O60/ |
= APPLICATION, DO NOT SCALE DRAWING
TITLE ASSY TENPIN PARTS GREMLIN LIST LOGIC BOARD 812 -COOl F DWG NO REV SESIGN ee APPR Se
DESIGN CHECK APPR 4
REVISION DESCRIPTION RELEASED CHG, > PER BtNIG7 Pe@ ECN 181 CHG'D PER ECW 33 (SUPERCEDED aaa CHG'D PER ECN 200
CHG'D PER ECN 208
Sut 5 \p & fier SHT G75 1b DP flee
ASSY. TEN PIN SH2 PARTS
DESCRIPTION
1OOLM 46V . ites
CAP. CER. .O54MF SOV CAR CER. .OO1LF SOV CAP. CEB. .O1WF SOV IJAF SOV
-224MF 1OOV CAP. F-. -O1IMF SOV CAP. TANT. lO2L4F 25V CAP. TANT. 6.844F 25V JOOAUF 25V
PCB TENPIN LOGIC
CONN PIN TEST PT CONN. FEM IOPIN TPI-TPI4, E1-E6
1C NESSS DIP
TME ASSY. TENPIN sH 3 PARTS 812 -O0Ol
| GREMLIN | LIST | LOGIC BOARD | DWG NO | OF 8 | rey |
| NEM | PART NO | aly PER ASSY | DESCRIPTION | REF DES |
| 314-0007 | 1 lic 74/93 | Us! | ||
| 3/4-0008 | 1 lic 74154 | U66 | ||
| 3/4-0009° | 71//C 7400 | 12 3,27,40,97,50,58, 67 | ||
| 314-0010 | 3/10 74/0 | U82, 83, 92 | ||
| 3/4- 0012 | 7 [ic 7408 | 77, 22, 30, 35, 36,6/, 8B | ||
| 314-00/3 | 4 |ic 7448 | v6és-7/ | ||
| 3/4-0014 | [a frevans | Ue | ||
| 314- 0015 | [ | 6 [1c 7404 | U4, 29,3 8,45,57,90 | |
| 3/4-0022 | 7 [1c 7486 | U3T7 | ||
| 314-0024 | 6 lic 7402 | U/-3, 26,60, 93 | ||
| 314-0027 | 1 [1¢ 7485 | U73 | ||
| 3/4- 0028 | 3 [IC 79164 | U7, 34,49 | ||
| 3/4- 0029 | 2//C 74/57 | U72,74 | ||
| 314-0038 | } [10 74163 | U2s | ||
| 314-00 41 | 2 |/6 74/75 | U64,65 | ||
| 314-0045 | 7 | 74973 | U18,19,41- 43, 78, 91 | ||
| 314-0057 | 1 | 74147 | Us2 | |
| 316-0044 | r | 7 [1€ PROM T/P UB | Ua | |
| 316-0045 | 1 [1/0 PROM T/P US | us | ||
| 316-0046 | _| |e [re PROM T/P VIC _ | U1 | ||
| 316 -00497 | —[ | [1 fre rRom T/P UN | Uti | |
| 471-0102 | ‘| | 25|RES IK N V2W 5% | (R2,4,5,7,/7 19,20 |
wa aoe us sew stow “ 73,8¢ /12-/26,78
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTES: & 19.9.0.0....0. 0.9.9.9 2 © Sages ase 408,
48 ADDED IN TEST AS REQUIRED CONNECTORS MOUNTED ON BACK OF BOARD (4 EA)
[2=0507 | TENET NEAT PARTS LIST syryed ore SEE DETACHED co
| sea Pia SES ist
E fee ar PC.AS SY. TENPIN LOGIC BOARD “Gremlin Industries, ine. (San bine eaters 925
812-0001 [ares EV F 17,000 REF
Shion
TP ia 45M SEC TRIANGLE etoee
RID 230A,
READY isan)
rea) 1 12 [88)" Rs ht)
omc NOLES, REVISIONS ave [UR DESCRIPTION are [ APPROVED 7 wei |
(s! 7748) ves AT 2a for of pag 5 3 a PAY a
Tt— PA:
a
BALL Roe (70 swo. 00.) Ve
TES Gy POWER a BUSS B
- ToroweR/ so Bes)“ ~<Douss's
eves (REV inDicaToR) SMS ry BRS) 2naao re) Tae Bs; aut F335
READY
GAME RESET
- CAPACITANCE VALUES ARE JA) 1/CROFARADS
- RESISTANCE VALUES AREJM OHMS NOTES: uncess oTHERWISE SPECIFIED
8 7 ear 5) We
master ees Set iem 8 e N Ke}
So] Se | eotindh rm PREG, ] PARTS List Duesaoee ae eres Gremlin industries, Ine. rouenances ARE San Digs, Catfornta 9138 : aes ROM are A wae per oram tecar) SCHEMATIC TENPIN aR 47 SEE DETACHED PaRTS| T lig} LOG/C BOARD SUTI-4_ OF 8 Gad oo SE [CODE TART WS | RANE W a T2-O00T |TENPIN D Bic -OCOl F ExT ABBY USED On l APPLICATION ‘DO WOT SCALE DRAWN sea wom rect < oF
(rT ease 4Plae (sh7 8) FIR
asa . enon 1 e +3 SAT CdS
PINS DOWN
AM — Rso | aaa REVISIONS (DESCRIPTION ‘ATE | APPROVED
PLCS)
STRIKE (eure)
ges 288000
gros
MASTER chock (SHTE) PINS DOWN 10
CAST BAL (SRT 648) 2nSo6o PriFMe ols/77
&>45Vv IN
WAKING | RIP ‘STeivS UP
SLEEPING RIP STEING ON
LIGHTN ING (TO SND. : Bo) a McRI06 a7 Bak $$ w LIGHTING.
TEN PIN
MCR 106
MASTER cvoeK (sate)
LeD (THIS SHT)
STRINE (OSND ao)
porns
BRIS
SEE NOTES oWEET 6 NOTES: cncess oTHeawise SPECIFIED (Sure)
Gremiin industries, ine. fine Beage, Catitersta 9325
parE [__] SEE _deTacnen PART LIST guTi-4 oF B SCHEMATIC TENPIN LOGIC BOAKD
eared)
OER (sHT ee)
CNA a (SHT) 12
10 nov “Gate ais ses REVISIONS DESCRIPTION zee
.e. Onte
R19
5] 7109) go. |. READY 4 (aT) Ciro)
2 PLAYER wa 6 ve ee 4 pan) We\6
Zz BEDG-
te8. HTSa Dy
2 SCORE (ris SHI
TEAM SB) 2 any, o [oel_qims sun 3at3
}2—y¥—+— jeu ©] yj of IPLAYER es whee? (sar 2)
(usa) LAMP ADV
STRIKE prs. curt) TEAMZ
eso 288201 Pats as9,
1 Scene Cais SHF
1 SEE NOTES SHEET ©. NOTES: uncess oTHERWISE SPECIFIED ™ MERIO6
FREE GAME
Rios
Tscone tats Sir)
Team scone chars SH GAME ENDS AT FRAME.
Gremlin industries, Inc. San Stage, Californin OTS SCHEMATIC TENPIN L06/C BOARD
E12-O0O/
(DO NOT SCALE DRAWING
TITLE. ASSEMBLY BOWER SOUND BD. TEN PIN
DRAWN L/PTAK LJ. SREMLIN J
CHECK 2 R [AUTH REVISION DESCRIPTION. ; RELEASED 7 ECA) 145
- ECN iS]
pet 43.19IT
- | i
jt UT [
——— s & ; SHT 6-6" OD" SIZE DRAWINGS .
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
)TITLE ASSEMBLY SHI FOWER SOUND BD 812-0002 [ TEN PIN DWG NO ors REV RELEASED DRAWN L/P TAK L.J. ENGR fds DESIGN Jcneck APPR/, x. ¢, LTR | AUTH REVISION DESCRIPTION CHECK | APPR A RELEASED
B ECN 145 L&C fa ECN IS]
f
SHUT 6-6" D" SIZE DRAWINGS
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
2 | 1
Rie
ans + <I
Reo} cea} [AH ft
RO os IEP +R Riza}
'‘+{R/z2 6 + Ries} (4PLCS)
SEE DETACHED PARTS LIST 8/2-0002 REVISIONS Zone | UTR ‘DESCRIPTION DATE in [RELEASED wld TALE
So] BT watt | Ge DESCRIPTION PARTS Lust ise aTRACT NO.
| Bivens anew exes | | | “ | Gremiin Industries, Inc. | |
| FRACTIONS | DECIMALS | ANGLES | ‘Sam Diege, Colternsa 9°73 | |
| : | xe | HEROS | OnE | |
| ae | PRA, praK Lv. [0/3/77 | ASSEMBLY | ||
| rrr | TA | Niluln| | RPOWWER | SOUND |
ZX MOUNT CONN. ON CIRCUIT SIDE OF BOARD NEXT ASSY, USED ON fF TENPIN NOTES untess oTHERWISE SPECIFIED ‘APPLICATION ‘D0 NOT SCALE DRAWING. BOARD SHE | CODE TENT NO] ORAWING NO REV D 812-0002 | C [seme 2x7
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | i |
420 REVISIONS
| a7 | FROG | ar STRIKE | vey | BALL ROLL | fo} | zone | TR | DESCRIPTION | Bare | APPROVED |
| apvernse Al | 2naaor | cnon | ® |
1k RS
| ik | ye | ve |
rm 60400" O40
| - | SNe | ASS | ||
| re BY | on | are | 7 | |
| GEN. | N42 | 2N440) | i | |
| DI] “sm oe | _- | fn a cs | + | D |
| no | Fey | Posie |
M TANT vev B00! i, onus at
| Ra | a3 | +i2v | |||
| 0 | 100K | 2Na4o3 | Rel | fee | rev |
| IK | 47K | a lo | Wal | ||
| r | ; | le Lie, | |||
| © | R22 | ala | |||
| RIB cla | val Yi) | 03 | L, | Rea | |
| pe | ue | 330n o5ur | ars | pees. " | 7914 47% | ales |s| 3.3% |
2nador $4556 im
| &S | Ina002 | a | esse fo 1 | ||
| wo | os | + | zO/6 | o | 7 |
| re | CIS a | -O5uF| | cz | Ce | |
| conn | Re | omit | louie | fur | Foour |
| RS. | 47K | TANT | TANT | ||
| > | +iav | ar | v |
cé Sue] @ vie
- 5s
| c | co + | a | c |
22uF 7 TANT
| “ev | WHITE | FROG CROAK | a |
NOISE. , A 83, |s ceneraror sure) Fe
200HZ NOISE 200 He NOSE tai ?
fF 7 C37 C32 Bae Sue Blue aso 47K 1200H2 NOISE
8 aye ion iS)
PM
| 51, 77 | (sH72) | BY |
LM 348 8 we © NS kel
+ S 1280 142 NOISE Gurel
LS [woth ho. Pyare l l PARTS UST Gromiin Industries, ine. Sam Biage, Catiforuts 920s A A SCHEMATIC POWER SOUND BD.
- © EDGE CONN. 2 INTER-CONAL OW BOARD 3 Caspr REF OES, USED C80, 0/7 G39 _RIE7, UIE CAPACITANCE. VALUES ARE. IN AICROFARADS :
| PAESISHINCE Vales Re IN OHMS “PW 5% (K~ 1000) | cso,ss | Ta 9061 (TEM Pin | ||||
| NOTE Si uncess orveRwise specirren | Cae Ee er Nes | _ | ||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 |
I Ovev
= c49 soon é
‘oO ik Prone ORE
Bi pp 200HE NOISE Qs eNader REVISIONS,
(warry
D0 THUNDER }
+N 4002 © >
® PIN BUSS
> as 2NS060 Qs
azz 245060 ees c + | tev Q THUNDER MODULATOR
R143 22K DESCRIPTION | DATE | ‘APPROVED
‘Ria! THUNDER o%
[o)
ve
im {| He [Mew 14 cosore Te + cD 4016 AE us our} Ahn ul ‘our|
Ss
CONTROL R34 RIA2 ‘50K
8/2-00021C
Gremlin industries, ine. Sun Biegs, Gatiforuin See
1DO_HOT SCALE DRAWING SCHEMATIC POWER SOUND BOD. TENPIN COST RO OR RO 8/2-0002
TITLE. ASSEMBLY PARTS GREMLIN LIST POWER SOUND BD. 812-0002 ar
TENPIN Dw NO REV
RELEASED DRAWN L/PTAK L.J. DESIGN CHECK APPR i {ne ere aura | REVISION DESCRIPTION BRAF RELEASED ECN 145 ECN ISI ECN 168
ECN_ 160 ECN 163 2fela2 ECN /96A ee
SHT 6-8"°D" SIZE DRAWINGS
TITLE ASSEMBLY SH 2 acl
POWER SOUND BD. 812-0002 oe cages | TEN PIN DWG NO power te — ie 00/3 EEEEE 2|CAR.E. /OOUF 25V | [/S/- Boo) a 20\CAR CER. .OSLUF SOV Tt mc “spade + CAP.CER_ /OOPF SOV CAP.CER .O2 LF 50V CAR CER. .0O/ UF SOV CAR CER, .O/MFE SOV CAP. CER. . IMF SOV CAP. CER. .0OO3 UF /00V CAR F. IF 100V C2,/3, 20,22 CS0,64-66
CAP. F. +0033 UF 25V
-OF?MUF 2OOV -334KF /OOV FTL 100V
CAP.TANT /OLUFf 25V a 7 u " J |CAR_TANT _/dkf 25V |AR TANT 2.2. Ur 25V CAP.TANT _33LF 25V C6, 12,17, 25,33,10,57 C 9, 39,37,44 C2/, 46
TITLE ASSEMBLY SH 3
- POWER SOUND BD. Bi2 - 0002 TEN PIN DWG ———ae ors a QTY PER ASSY a DESCRIPTION i ee prs E | to 0/06
CONN. FEM 10 PIN 2l2- 0002
IC. LMI4IEN DIP 1.0, LMS66 CN DIP
- LM348 O/1P CLM 3407-72
- LM 320T7-/2 AC. LMSS6
14.0. 400/ 1 |4C. MM 5837 cH 2|RES 270M //2W 5% : S2;IRES /K V2 WwW 5s u" a at n ”
4 fO, 7 ’
1 4 7 - y4S)4 9) ! > 106,107,110, U1, 149,150, 15 4,/55,158 162, 163
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
FOWER SOUND BIZ - 0002 GREMLIN List TENPIN ae OF 68 2 Me QTY PER ASSY PTION PaRTNO' =F T TT dT DESC P| eroses RES 56K I/2W 5% RES 62K WeEW SS 6.8K //f2W 5% 68K V2ZW5% 82K J2W 5% RES 5/0 1/2W 5% RES /f [Ww 5% RES 820N //2 S% PoT /K TRIMMER PoT /00oK 50K RIS, 76,25,79
R100, 130 R90, 94 R28, 99 IN) S TPO IN Jot a pe
cTs R/I38-/42
481-000! 481- 0006 /MN F002 DIODE _/N 9/4/1N4148 01,2, DBS, 8- 13, 16,3
XISTOR 2N9403 x/STOR SCR 2N5060 X/ISTOR SCR MCR/06-1 X/ISTOR 2N 990) “a uv “ “uo Q3, 14, 20, 26,31, 32, 57, QS,6,27 Qi Q2,4, 7-13, 16-19 23-25,28-30 33,34 , 38 la@2r, 22 482- 0009 982- 00/2 9782-00/4 a aw
at 2|x/STOR TIF 29 X/STOR 2N40 93 HEATSINK 295-1 de aw 482-0016 982-0025 530- 0007
Bej—+ [Rae fs
fi R46 +faraal
R63 Ga) aa f pasap, fesoh (ard
+Rishk {C75} ais?
é REO} R83 + pokes
[reo
LAUSE ONLY NATIONAL SEMICONDUCTOR LMS6E PER ECN /96A RO
LX MOUNT CONN. ON CIRCUIT SIDE OF BOARD NOTES uncess oTHERWISE Tiz-G061__ |TENPIN NEXT ASSY USED ON [APPLICATION DO_NOT SCALE DRAWING. 5s 4 812-0002 |G
SEE DETACHED PARTS LIST 8/2-O002
TONLESS OTHERWISE SPECIFIED EN TW INCHES. FRACTIONS DECIMALS ANGLES = xe + ‘APPROVALS | om aaTERAL PRAWN TAK Lu. FERED) 7 oo Gremlin Industries, Inc. San Diege, California 92003 ASSEMBLY POWER SOUND
812-0002
FROG IN cRoay
To Gen. Luin 6 5
STRIKE IN
ve 04001 + 4
RIB cra 3302 .o5ur 2N440/
cis Joule TANT Rg 3.3K ce s, rae jet Qa + J 2N44901 Ry Ll tout TAUT FIN BACKGROUNN SOUND
lev BALL ROLL IV ge REVISIONS DESCRIPTION ‘DATE | APPROVED.
B ware FROG CROAK - 3 GENERATOR P tsi) fo LM 348
u7 tn348 “e
200HE NOISE He NOISE z I (sHTe)
<8" (saray
RS9 47K 12002 NOISE
caz Saute Film B
iV)
~<a ns) 8 Le} NX Ra
R76 68K
| oa oR NOMENCLATURE T l Be] wehhnd vo. yee l PARTS UST
- © E0GE Conn.
- SD INTER-CONAL ON BOARD. 3.LAST REF OES. USED C79, 016 G36 KIE4, UIE
- CAPACITANCE. VALUES WRE SISTANCE VALUE 5 ARE AKE IN AVC ROFARADS IN OFS NOTES oncess ormenwise srecirien
8 7 Yew Sh (K +1000) Gremiin Industries, Inc. ‘San Diege, Californie 92073,
@.35,3¢ AS0,/01, 124- 129,131 135 137 D4,7,14,15 ues 72-9001 |TENPIN C8, 70,71,74 XT ASSY USED Of UNUSED REF NOS. [APPLICATION DO_NOT_SCALE_DRAWING SCHEMATIC POWER SOUND BD. 7TENPIN
(BOGE TENT NO, DRAWING RO.
D 812-0062
[SCALE Wee
+I9VL.€,
uM Panne] —O tavoc. © ms 0 + 48 49 SautT TT ioour ‘ FILM
Rea irs AUDIO AMP. Sf 3 Add 4y—
contro. Yi css) L tout Bate avec
ese foo E
pone ih Prone Worse AUDIO OUT © ,
- C7) (ur 7)
24403
Dis INSI4
RI30, sin Q THUNDER MODULATOR
2nq4qor Te
our > BUSS A {BALL PATH)
OZ sig >i
BUSS B (BALL PATH)
or IN S14
O (sHTD PIN BACKGROUND
R43 22K
Greenbin industries, lee. Sam Deape, Cattorvan 9108 SCHEMATIC POWER SOUND BD. TENPIN SE [OOOE TOENT RO” ¥ Si2-000z2 | 6
ee
bane BOARD DWG Enea OF 3
a APPR REVISION DESCRIPTION DRAFT | CHECK | APPR RELEASED : Bciae | [8 [a7] CHG'D PER ECN 159 Sed CHG6G'D PER ECN 20/ oa?
FORM NO. 001-1500
TITLE Gremiin Industries, Ine. PARTS ASSY. TENPIN 8/2 - 0003 SH2 c an Dives, Calidormis 92rt2 LIST | ;4MP BOARD DWG NO OF 3 | REV TY PER ASSY eM PART No. +2 DESCRIPTION REF DES iSO- O00S CAP E 4700MFD 16V /SO- 0008 CAP E 2200MFD 25V 1S 2- 00/7 CAP F .3B3MF /OOV /7O0- O107 PCB T/P LAMP 2//- 00/8 CONN FEM. QUICK YB 212-0003 CONN M_ 10 PIN 7 1212-0020 CONN M RTA 10 PIN 8 |3/3-00// 1C. LM323K 9 | 390-0002 SKT LAMP
- 471-047) RES 4700. 1/2W5 h% 11 | 474- 00/0 RES /0O. SW 10% 48/-000/ DIODE /N4002 48/- 0002 DIODE MRT7SI/ ci 04,05 C2,C3
D6A- DIEC, D24- O26 DI, D2, D20- D23 /3 BRESOGRORRod 4181-0004 DIODE MRSO/ D3-05,0/7-D/9 482-0010 XSTR_ PE80SO SCR 2N6400 SW SINGLE POLE 4 POS SW SINGLE POLE 8 POS HEAT SINK
LOGIC CONN.
| 5 | 4 | 3 | 2 | 1 |
REVISIONS
| =f | DESCRIPTION | = seit |
| ” [RELEASED | Fie | LaF |
LOGIC BD CONN. SEE PUL FOR FURTHER REVISIONS _ eo
| | | "oS = | BALL. PATHS ———-—— | jou |
> > evans <SyaLann o st
| f | RECT. AC | G)BUSS A |
Les \Dauinn BUSS B apiac jixiom, [) -<euss c , PINS UI lav RECT AC ‘BUSS PINE UP BUSS
| ea | ga | 7 | - | 414 | |
| =r] | Or | Tl | RECTAL, | ||
| Hl | tony HO O | O | O | O | O |
| i] | ever mms Tai 43! | 92 | PP | PP | PR |
RED _> | 4 GEN. ILLUM,(TYPS6 LAMPS) #756 ONLY \ CATHODE. SEN WH | Eonw fat 4I9VDC._ UNREG || t2 Oe !]]560-O11A c
| LIGHTNING | RED rs | | tt | |||||||||
| = | WEATSINK | TVOe UNFEG | Sx ANODE, | ||||||||
| Fr | -— if | Tos | pie | illa38- 0001 | “> | ||||||
| 45) LS) 3 | 5 | 6 | 7 | 8 | 5 | fr | aa | ise | BRN ase | GRY | © Poy |
| 5) =) © —6) ES E65) 65) | BLK | € vio wasory | | |||||||||
| ens | Q@ Q | | | > |
+ 901
| wn | t | RED 3) || caw _ MASON | eel |
at STEINS UP] IP DOWN TEINS DOwN| | J[BRNAWHT | <)
| oe Q 4 @ | De icc |||] "°3 | | & |
PWR,
| an | RED/WHTS | | ° | |||||
| | ® g om | fe | a | ®, | H | LL | + | spre matt “ah 2 CONN |
fl =
| NSVAC. — 250v | NOTESSUNLEGS OTHERWISE SPECIFIED | GND | <9 GND |
| l25W | 2 AMP SB | LALL UMARKED LAMPS 18/3 ONLY | GND |
| ZALL GwarneD. oloDes 4002 | Re | > | |
| F | 4) BALL CAP. VALUES ARE IN) MED | on | B |
BRN] |BLK GND
| 7 | FRAME = | >——> | |||
| +5v De | Gee. | sw.! | sw2 | COINBOX CONNECTOR | U |
| }260 -0001 | FREE GAME FOR | |GAME_ENO | Ox & | ||
| es | ORO | : | |||
| IST UP SCORE | @ 2ND UP SCORE | Ne | 9 |
A Q
| HUNDREDS | HUNDREDS | a | ES SA | ma | 9 |
—a ey
| 7 | F ae fy | "12 | B | (J | |||
| rR | EM | O1 OL OL OL OL ® | 5° | ||||
| @ tens! |@)} | Q) jenits @) | WHT | LOGIC BD CONN | |||||
| < | e | = | pic fsiav SEP 1S RVR | = | Faro | SoC | = |
a Se Scar
| a) | ——*"_| 20-0010 FRY | SEE DETACHED PARTS LIST | ||
| —H | ND, | Desens sem ms | = | ‘Gromiin Industries, Ine. |
Put FOLERAnES ‘San Binge, tatttornde 9nrsl
| { | = | = | Be * | APPROVALS, | OAT | A |
| — | GROUND | arena | . | ASSY TENPIN |
©1018 BBB fa] LAMP BOARD
| CSS QO OG OO | Gaal | SE EBC WO I A | a | |||
| +5V DC | LOGIC BD CONN. | 12-2001 | Zac | D | 8l2 -O003 | G |
| APPLICATION | (DO _NOT SCALE DRAWING | SCALE NONE | swee? 3 OF | |||
| 5 | 4 | 3 | 2 | 1 |
E ASSEMBLY COINBOX UNOECALED 8/2-0005 SH/ | 4 N oF 3 | REV [LTR] DATE | [DRAFT | CHECK | APPR_| | A [ajeca] RELEASED be 44% [FF7. |
FORM NO. 001-1500 TITLE Gremlin Industries, Inc. PARTS ASSEMBLY SH2 A LIST |co/nBOX UNDECALED oF 3 | rev
QTY PER ASSY PART NO [—] DESCRIPTION REF DES
2u-ooo | | S|CONN CRIMP _CO/N BOX 2/i- OOOS 6 |CONN CRIMP LOCK
D / / 2/2- 00/6 CONN, BLOCK IOPIN FEM
220-000/ 220-0008 220-006! COIN BOX COUNTER DIGITAL, 6V COIL COIN LOCKOUT 280-0004 CL/P WIRE HOLD DOWN 280 - O006 BUSH/NG) S/REL 3//6 28O- 0073 BUSHING S/REL SPLIT 600-0006 CABLE GCNDCT (30 FT. CUT LENGTH REF, SCREW PAN HD *6-32 X 3/8 (SELF TAPPING) SCREW FLAT HD‘6- 32X 3//6 WASHER INT. TOOTH ™%& NOM.
FORM NO. 001-1501
REL EASED
}—-COIN MECHANISM REF
30 FT. (UT LENGTH)
COUNTER DIGITAL
SPARE WIRE
con COIN LocKouT
SCHEMATIC DIAGRAM
COINBOX UNDECALED
[CODE IDENT WO, DRAWING RO. 812-0005
LOOP ANT.
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES: PURER EONS ARE. Gremiin industries, Inc. FRACTIONS DeciMALs Antes eT ——— San Diego, California 92923 —as 49 MHZ TRANS/INTTER, K-92 =a (SCHEMATIC DIAGRAM) CODE IDENT NO. [DRAWING NO. KEV APPLICATION DO NOT ———_| DRAWING
2, ALL RESISTOR VALUES OHMS, 4 WAIT, 10% NOTES : (UNLESS OTHERWISE SPECIFIED)
I, ALL CAPACITOR VALUES IN MICROFARADS.
1I90-0009\ A exe ONE [wer 1 owl _|
REVISIONS: DESCRIPTION ttm
XTAL 43,3750 RI9_ACIT maz 40K] ,1
RB Clo eka Troe 84%
Re 190D- 00/0
gry | cope PART OR NOMENCLATURE REQD | {DENT IDENTIFYING NO. OR DESCRIPTION PARTS LIST. UNLESS OTHERWISE SPECIFIED DIMENSIONS Age IN INCHES Gremlin industries, Ine. ‘ARE: DECIMALS ANGLES San Diege, California 92073
- meee —leea) 49H RECEIUER, K-29 es ee (SCHEMATIC DIAGRAM)
| #2-0001 | 2, ALL RESISTOR VALUES IN OOS, V4 WATT, 10%. CODE TERT FO. [DRAWING PS
- ALL. CAPACITOR VALUES IN MICKOFARADS, 12-0001 190-0010 1 NEXT ASSY. USED ON NOTES : (Ones OTHERWISE SPECIFIED) (APPLICATION
PRIMARY WINDING HOOKUP PROCEDURE FOR WALL GAME TRANSFORMERS,
PART NUMBER 560-0110A and 560-0111A.
Brown wires to one side of line voltage cord.
Red/white wires to other side of line voltage cord.
Brown wires to one side of line voltage cord.
Black/white wires to other side of line voltage cord.
Brown wires to brown/white wires and to one side of line voltage cord (tie all five wires together).
Red wires to red/white wires and to other side of line voltage cord (tie all five wires together). FOR 230 VAC OPERATION HOOK:
A. Red wires to brown/white wires.
B.
c.
D. Cap off black wires separately.
E. Cap off black/white wires separately.
FOR 200 VAC OPERATION HOOK:
A. Black wires to brown/white wires.
B.
Cc.
D. Cap off red wires separately.
E. Cap off red/white wires separately.
FOR 115 VAC OPERATION HOOK:
A.
B.
Cc. Cap off black wires separately.
D. Cap off black/white wires separately.
FOR 100 VAC OPERATION HOOK:
A. Brown wires to brown/white wires and to one side of line voltage cord (tie all five wires together) FOR 100 VAC OPERATION HOOK (Continued)
Black wires to black/white wires and to other side of line voltage cord (tie all five wires together) .
Cap off red wires separately.
Cap off red/white wires separately.
Use wire nut type connectors for all hookups and cap offs and
make sure all connections are insulated before applying power.
TENPIN SERVICE NOTE NO. 005 COIN CREDIT Page 2 of 2
PROCEDURE: (Cont'd.)
- Return game to normal operating conditions.
9, If there are any questions concerning this service note, please contact Customer Services at the Gremlin factory.
GREMLIN INDUSTRIES, INC.
Mike Gawarecki Supervisor, Customer Service
or LeRT HHA CSKNCR Ur ids iu.
uD 7 oz §
ND 9%
qe
JUMPER WIRE 30 a PDbED connect peel? tT voe commeax 1 OuTPT Pin
ah do 4h
FRONT VIEW
Figure ¢