Championship Bowling
Championship Bowling (Seta / Romstar Inc., 1989) · Document · 22 pages · 25 sections · original scan
vailable in Upright and Cocktail Kils
UNIVERSAL JAMMA CONVERSION KIT (Vertical 4 Player Alternating, 1 Trackball, 3 Button Game) iz
I
zZ
Installing Your
CHAMPIONSHIP BOWLING
New Game Package
Table of Contents
New Game Package Contents ........ 060. e cece ence eee eet e tenn eet n eee 2
Power and Monitor Requirements
Recommended Tools and Supplies
Installation Procedures
Coin Meter Diagram... 6. eect teen ener e eee enter eee nents 10 Monitor Sync Tips 6.6... eee cece ee ee eee en een t een een ee tense nes abl
Control Pane! PositionINg..... 6... c ccc cece eee ene eet e eee teen ene eens 12
Factory Settings ........ cece cece eee ee eter nett eben tee ee eee et ennnes 16
DIP SW Diagram... 6. ec eee ene n erent ees 16
In Case Of Difficulty 0.00... ccc cece ete eee n tenn tent ne tn ntees 19
Main Harness Connections .. 1.0... cece cece ncn eee eee ne ence ene nnn nes 20
CHAMPIONSHIP BOWLING NEW GAME PACKAGE CONTENTS . oar
| DESCRIPTION | PART # || DESCRIPTION | PART # | |||
| 1 Main Printed Circuit Board (PCB). | 6301 « ff Khtarquee Ss | 6303 | |||
| 1 Monitor Bezel | ~ | 6308 | 1 Control Panel Overlay | nt | 6307 |
| 1 PCB Feet Assemble | 0524 |} 1 Set Side Graphics | 6306 | |||
| 1 Connecting Wire Harness (amma) | 0215 | 1 Set Play Instructions & Function Labels} 6304 | |||
| 1 3" Trackball | aa | 6309. |] 1 Installation Manual | | | 6302 | |
| 4 Button Holders | 0221] | 1 Metal Trackball Template .overkay* | 6309A | ||
| 2 Red Player Button | ee | “0229. |] 1 Molex 6 Pin Male Connector | 6309M | ||
| 1 Blue Player Button | Pee | 0233 | 6 Molex 22 Gauge Female Pins | 6309P | |
| 1 White Player Button | . | 0235 |
Ba A
Vertical Mount Raster Scan Negative Composite Sync Required for Jamma Compatibility 7 amp minimum | amp minimum 1 amp minimum
ROMSTAR inc.
Invites You To Use
OUR PHONE OR FAX NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER ROMSTAR GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS.
ROMSTAR, INC. 22857 LOCKNESS AVENUE ® TORRANCE, CALIFORNIA 90501 TECHNICAL QUESTIONS — SENIOR TECHNICIAN DARRYL WILLIAMS EXT. 119 RMA‘S / PARTS QUESTIONS — PARTS MANAGER AUDREY SMITH EXT. 112
PHONE (213) 539-2744 FAX (213) 539-3626
WARNING
Federal jaw provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.
The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.
Before You Get Started. . .Stop!
Does your new game package include all listed parts? (Is it complete?)
- Isthe game you have chosen to transform able to supply all the required voltages for the new game?
- Is the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
- Do you have the necessary tools? (See the recommended tool list)
Caution
F.C.C. Regulation Compliance Operation of this equipment in a residential area is likely to cause interference
- in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference.
Recommended Tools and Supplies
ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 114” © 7/16" Drill Bits 1/4" Plex Bit 1-3/16" Chassis or Sheet Metal Punch 1 1/4” Plex Hole Saw Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Patience Common Sense
Dip Switch Tables
Optimize Your Profits Painting Supplies (if you do your own painting) Paint Brush and Paint (don’t forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Nights Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” © 1/8" © 3/16” Masking Tape 3 1/2" OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapy.rs work GREAT!)
Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren’t running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!
Installation Procedures
Something To Think About Your finat product will be a mew game. You have made a wise decision to transform a game that has seen better days in the all important cash box into a mew game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that's it] We provide the rest. The end result is... anew game at 2 very low cost. Fact: Spend alittle time on the cabinet’s appearance (i.e. Marquee, contro/ panel and cabinet graphics}. With alittle paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of anew game package. The new game !ook should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary glitches do not occur. Remember: You are creating anew game . If you have any questions or just need some advice on any of your new game transformations, don’t hesitate in giving a member of our technical staff a call.
Let’s Get Our Hands Dirty
Preparing the Original Game for the New Game Remove the following:
| |, | Main logic boards) | 4. | Monitor Bezel |
| 2. | Contro! pane! | 5. | Marquee |
| 3. | Monitor plexiglass | 6. | Graphics |
( would recommend painting your cabinet to give it a fresh new look. You may consider having an auto body shop take care of your painting needs.
If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexigiass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.
Time To Install Your New Goodies
Before You Start. . .Remember DO NOT Do This Work With The Power On!
Logic PC.B. Mount the logic board securely (away from power supply). A Mark and drill pilot holes (3.32”). B Install the P.C.B. into cabinet. Use feet and spacers supplied and adjust them so that the screws will go through the holes in the cabinet.
Wire Harness
Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Ever if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.
Connecting the Wire Harness to the Existing Wires When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.
- Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
- Solder the new wire designated for that position to the original wire you just stripped.
- Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
- Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game , not a sloppy conversion.
Power Wires
- Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
- You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don't overload the edge connector pins and cause them to “burn”.
Monitor Wires
You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.
Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.
Coin Door Wires
- Connect the designated wires to the coin switches and meter. (See tech tips}
- Youcanconnect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
- Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.
GUESS WHAT?
You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.
Smoke Test
What Test?
Don’t worry. Ali this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.
- Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
- Make sure the logic board, monitor and power supply are securely fastened in place.
- Double check the connectors to be sure they are wired and connected properly.
- Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.} Also, be sure you set the dip switches for “DEMO WITH SOUND”. This will enable you to hear as weil as see that your new PC.B. is functional.
Time to Apply Power: Look and smeil for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED)
- Listen for game sounds. If after one minute you Nave not heard any sounds: A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board.
- How is the monitor image? A) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative (see tech tips section).
NOTES:
B) Now how’s your picture? © It it centered? Is it too bright or dim? @ Is it in focus? Check your monitor manual for these adjustments. If your screen looks “off”, then your new game transformation may have been in vain. So let's take the time to make the monitor look great. C) Is the picture upside-down? Refer to your monitor manual - switch two horizontal yoke wires and then switch two vertical wires. (Pull the pins in the connector on the monitor P.C.B. to switch them.) or check Dip Switch Tables
Control Panel Assembly
- Remove the buttons, joysticks and wire harness and put them aside for now. Do not remove the original panel overiay until the new holes have been drilled.
- Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the controi panel. We fee/ that yournew game investment is well worth protecting. . .and the control panel is the first place to show wear and tear. ¢ You will need to cut this piece to size. Use the control panel as a template. © Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass.
- Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes.
- Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter.
- The holes are now ail cut. Smooth them out on your panel and plexiglass with a fine toothed file.
- Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peei off the bottom half and do the same as you did for the top.
- Adhere the instruction and function labels.
- Install the Plex Control Cover over your completed new game panel.
- Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panei wiring if possible)
Marquee Installation
Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers.
Be sure the light behind the marquee works. Everything should always work on anew game. Take your time ... Don’t forget this is going to be a new game.
Side Graphic Installation
Be sure sides of game are clean and free of old adhesive, dust, etc.
- Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet).
- Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing.
- Remove any small bubbles with a pin or razor blade (pop them}
Finishing Touches
- Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware.
- Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can't get a coin into it.
- Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking.
- Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game . © Are all the player controls working? ¢ Are the game sounds present? Is the volume level proper? © Are the dip switches set properly? Well, that’s about it. Good Luck.
Coin Meter Diagram
To attach a coin meter, use following diagram:
+5VDC +12VDC or +24VDC
DIODE (iN4004)
COIN SWITCH TONAIN
HARNESS COIN OR COIN | DIODE {IN4004)— CouNTER SWITCH GROUND —= OUTPUT
Star Tech Tips We are grateful to Star Tech Journaltm for allowing us to publish the following excerpts from their journal.
- Monitor Sync {fyour monitor does not have dual polarity positions for sync, you may use one of the following methods to get your game going. CURE 1: Install a simple one I.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new |.C. and then connecting the pawer pins only to the existing chip. (See Fig. i) Next connect the sync wires as shown in Fig. 2 (Note: Figure 2 shows a hookup for either composite or separate syncs.) HORIZONTAL SYNC INPUT FROM PCB, 5S Vee SVDC [PIN 14) (OR COMPOSITE SYNC INPUT} SOLDERTO HORIZONTAL SYNC OUTPUT TO MONITOR EXISTING CHIP (OR COMPOSITE SYNC OUTPUT} VERTICAL SYNE INPUT FROM P.C.B
VERTICAL SYNC QUTPUT TO MONITOR
FIG. 2
BENT PINS NEW IC. }
FIG.1
CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85xi40B.
Cut the traces on the solder side of the board between input pins 5 & 6to the unbanded (anode) ends of diodes X201 & X202. Add MPSAS6 transistor as follows: Collector to anode leads of diodes X201 & X202. Base to pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode ZD201. Insert a IN4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3) REOI ad MPSAS6 GREEN2 ©
° ° BLUE 3 GND4 FIG.3 VERT. 5 HORIZ. 6 iN4148
CUT TRACES
X201 1
- Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”. CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radiat lead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the C303 location. CURE 2:Connect IN4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.
IN4148
NEG: SYNC INPUT
| r- | -l- | = |
tO v O1 ono ee Te
| FIG. 4 | 3 | 2 | 7 |
GND BLUE GREEN RED rc ‘ace 7o_0o_0 6}
| 6 | 5 | 4 | 3 | 2 | 1 |
IN4148
CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from W102 to either J2 or J3.
CURE 3: For Wells-Gardner K4600 series monitors Replace C 356 (4 7uf 25V} on the Horizontal vertical! board {vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune with the horizontal width pot.
Control Panel Positioning
start ia Q wn O O _/ \_ LEFT HOOK RIGHT HOOK
ILLUSTRATED
PARTS LISTS
AC GROUND
P ISOLATION t TRANSFORMER 7
NOT USED ON MOST MODELS
| JYeliow COLOR MONITOR
MONITOR CONNECTIONS
- VIDEO LAYOUT
COIN METER LAYOUT 95-4115-00 MICROSWITCH WITH GOLD CONTACTS
Exploded View
53-9212-00
56 PIN EDGE CONN. PIN-OUT CHART (JAMMA COMPATIBLE)
| WIRE COLOR | SOLDER SIDE | PARTS SIDE | WIRE COLOR |
BLACK
BLACK
RED SV
RED 75V
WHITE -5V -5V
YELLOW *12V +12V a
KEY KEY
COIN COUNTER 2 COIN COUNTER 1!
COIN LOCK OUT 2 COIN LOCK OUT 1 RED
WHITE/BLACK SPK [-} SPK (-} WHITE
OP.-BLU/BLACK N.C. z/r-lxlelx NC. BLUE-OPTION
GREEN VIDEO GREEN VIDEO RED RED
GRAY VIDEO SYNC VIDEO BLUE BLUE
RED/BLACK SERVICE SWITCH VIDEO GND BLACK
OP.-BRN/BLACK TILT SW. TEST SW. BROWN
COIN SW. 2 COIN SW. 1 WHITE
WHITE/GRAY START SW. 2 START SW. I GRAY
WHITE/VIOLET 2P XDIR iP XDIR VIOLET
WHITE/BLUE « 2P YDIR IP YDIR BLUE
WHITE/GREEN 2P XCLK IP XCLK GREEN
WHITE/YELLOW 2P YCLK 1P YCLK YELLOW
WHITE/ORANGE 2P HOOK R 1P HOOK R ORANGE
WHITE/RED 2P HOOK L 1P HOOK L RED
WHITE/BROWN PLAYER SELECT BROWN
GREEN/WHITE NC N.C. BLUE/WHITE
YELLOW/WHITE N.C. alo]ols|N|~| x) €)| <j) C}a}u/ala N.C. RED/WHITE
BLACK GND GND BLACK
OPTION-BLACK GND GND
WICO 3” TRACKBALL WIRE COLOR TABLE
| WIRE NAME | POSITION | WICO COLOR | JAMMACOLOR _ TECH. NAME | |
| 1 PL.UP | PIN 18 | BLUE | MOLET | X DIRECTION |
| 1 PL. DOWN | PIN 19 | GREEN | BLUE | Y DIRECTION |
| 1 PL. LEFT | PIN 20 | VIOLET | GREEN | X CLOCK |
| 1 PL. RIGHT | PIN 21 | YELLOW | YELLOW | Y CLOCK |
| +5 volts | pin 3 | RED | RED | 5 VOLTS |
| ground | pin! | BLACK | BLACK | GND |
BLACK-OPTION
RED + SV. 5
“Ww ca Y23AN & =\C_] Blue voi 5 = VIOLET voz yok puoi,
“WwW
y | 8 Valo] ver Hor 3 = IC GREEN HO2 | 4
BLK GND
Test Mode Procedure:
To enter Test Mode, turn Dispswitch #1 ON on the PCB. Turn power off then on, or press the small reset button beside the volume control (SW/ 2 LOC. M-13}.
Test mode screen | is a video color/crosshatch screen. To go to the next Test Mode screen, use Start button.
Screen 2 will have dipswitch setting and some ROM information. Thetrackball test is the letter in the gray box. Move the trackball to move the letter (this part of the test is useful when buildling the kit, for checking proper operation of the trackball}, Press start for the next screen.
Screen 3 is a music, sound, voice and animation test. Move the trackball to move the bowling bali pointer to the category you wish to work with. Use the left hook and right hook button to controi the category advance and activate mode. Press start to continue.
Screen 4 is a game adjustment screen. Use the trackball once again to move the bowling ball pointer to the category, then use the right hook and left hook to change the setting. More details on this category below.
Screen 4 is a highly critical screen, as it controls the actions of the game. The trackball speed setting is to adjust trackball responsiveness to the player. Move the ball to this setting and use left and right hook to change the value. We recommend a setting of 10.
The timer setting will disable the time. We recommend using the timer.
Thethrow mode affects the little animation of the player throwing the ball. If set to quick mode, the animation will occur in less than a second. In full mode, the animation of the ball throw will be a natural speed (1-3 seconds). \We recommend quick mode.
Game Difficulty is used to adjust the hardness of the game to the custom needs of your location. We recommend a setting of two (2).
The INIT backup AREA is used to clear the bookkeeping RAM. If the RAM gets bad data in it, the machine may display weird symptoms. You should also erase High Scores when you INIT backup RAM. Some possible symptoms are: screen garbage during the high score display, a “Bad ROM version” error, or very strange game settings. If the problems persist, check your battery voltage, make sure the switch by the battery is set “ON”, or your RAM may be bad, Call the ROMSTAR service department in that event.
Screen 5 is various game bookkeeping data. it shows game coins, scores, and other various bookkeeping data.
OPTION SWITCH SETTINGS
The following option switch settings were designed to allow the customizing of various game features to suit different environments. If used wisely, the flexibility they offer can maximize game performance and increase potential earnings.
DIP SW [1) Item Condition 1 2 3 4 5 6 7 8 Game > | OFF Test Mode Test ON i * OFF
Type Upright
Table Top ON
OFF * OFF Freeplay ON ON OFF =X OFF Demo Sound | ON ON NORMAL * OFF Screen REVERSE ON N/A OFF | OFF | OFF Don't Teuch N/A ON| ON| ON
- Rec, Setting
TEST MODE
TO ENTER: ADJUST DIP SWITCH 1 POSTION 1 ON / TURN ON POWER
TO EXIT: PRESS START OR READJUST DIP SW/ AND RESET POWER
SCREEN 1:
SCREEN 2:
SCREEN 3:
SCREEN 4:
SCREEN 5: VIDEO COLOR AND CROSSHATCH TEST
DIP SW, 4-16MEG ROM, COIN, PLAYER CONTROL, AND. TRACKBALL TEST
MUSIC, SOUND, VOICE, AND ANIMATION TEST RIGHT HOOK = + # INCREASE, LEFT HOOK = — # DECREASE
GAME ADJUSTMENTS; TRACKBALL SPEED (1 FAST — 19 SLOW) TIMER (ON / OFF) THROW MODE DISPLAY {FULL - QUICK) GAME LEVEL (1 EASY - 5 HARD) RESET SCORES AND REPLAY. / SCORE ADJUSTMENTS
BOOKKEEPING DATA: COIN, REPLAY, GAMEPLAY, AND SCORE DATA
TO CONTINUE: DEPRESS START BUTTON
* FACTORY SETTING PLEASE SET PCB AS FOLLOWS:
Sle} s)s]2 z 18/6/8/8) _| - & &)/5|7 a} G| a] a
zlelele 3/8/8}8/8 E(2/$/S)2) 2/2 2lelelels Ra Q)el eee
g & é = s als Bl2|8la|" 31s a E Q 6
glé alg Zz Z\5 ele E/2/°|2/3]e|° ule S
Zz elalele Olas Si2 ef al,|Fia/al® gel Fye lel aie Ziel |e/8]8|2
TOP CENTER
- To switch VERTICAL direction { 4 ], exchange the BLUE & VIOLET wires
- To switch HORIZONTAL direction {—=], exchange the YELLOW & GREEN wries.
, *
SAMPLE HOLE TEMPLATE (Not To Size)
MEDAL TEMPLATE HOLE LAYOUT {To Size}
CHECKPOINTS IN CASE OF DIFFICULTY PROBLEM / CAUSE-CURE No Raster/No Video
- Check A.C. line cord
- Check line fuse
- Check monitor brightness ~ Check power switch and/or interlock switch ~ Check all solder connections on line filter and transformer ~ Check for proper orientation of the PCB connector
Raster/No Video ~ Check all PCB to monitor connections . ~ Check power supply voltage on PCB
No Video/Game sounds can be heard ~ Check monitor brightness = Check all PCB to monitor connections
Wrong colors
- Monitor needs degaussing ~ Check for proper wiring between PCB and monitor
- Check monitor adjustment and adjust if necessary
4 Wavy picture
- Check monitor ground is properly connected to monitor : ~ Be certain sync inputs are properly connected to monitor ~ Check horizontal hoid adjustment
Horizontal/Vertical Roll ~ Check horizontal and/or vertical hold adjustments.
- Check for proper wiring of syne from PCB to monitor
No sound
- Check for -5 volts on edge connector of PCB Check volume control potentiometer adjustment ~ Check for +12 volts on edge connector of PCB
- Check wiring from PCB to speaker —Check speaker for low resistance between the “+” and -" tabs
Bad sound ~ Check wiring to speaker for bad solder connections ~ Check sound with another speaker
No switch input ~ Check ground connection to switch/es
- Check wiring between PCB and switch/es for proper connection
- Check switch/es with an ohmmeter to verify proper operation
Switch operates incorrect function
- Check wiring between PCB and switches for proper orientation
- Check wiring for shorts between switch inputs
No coin meter ~ Check wiring to coin meter
- Check that +5 volts is on "+" side of meter
- Verify a +5 volt meter is used
When coin switch is made and meter pulses, the screen blanks out and/or game resets ~ Verify that a meter with a diode is used
- If no diode is built in meter a IN4004 can be used across the meter. Cathode to “+” side of meter and anode to "-" side of meter
Trackball not working
- Check 5 volts, check gnd, check direction and clock connections Trackball position bad ~ Check trackball mounting and x or y direction and clock
nv co
JAMMA DA.BK
Ground
JAMMA SK.GR
Black
+SVDC Red Red +5VDC +SVDC Red
Red +5VDC
Red Red +5VDC +5VDC Red
White -SVDC
-SVDC White Green -SVvOC ~SVDC Green
Yellow +12VDC +12V0C Yellow Yellow +12V0C +12V0C Yellow
Post Post Post Post
Brown/White | Coin Counter 2 Coin Counter 1 Bm/wht Coin Counter 2 Coin Counter 1 Brown
Red/Black Coin Lockout Cain Lockout Red/Bik Coin Lockout TIN Ime lu} ols jojo Coin Lockout
White/Black ‘Speaker {-) Speaker (+) White ‘White ‘Speaker [-) ‘Speaker (+) White
Audio
Green Video Green Video Red Red Light Green Video Green Video Red Pink
Gray Video SyNC conemey Video Blue Biue Gray/White Video SYNC eenvmes Video Blue Sky Blue
Red/BIk Service Switch Video Ground Black Violet Service Switch Video Ground Black
Tilt Switch Test Switch Brown Gray N/A N/A Orange
Wht/Bik Coin 2 Coin 1 White Coin 2 Coin Violet/White
Why/Gry 2P Start IP Start Gray Wht/Bik 2P Start IP Start, Black/White
Whr/Vio 2P Up 1P Up Violet Brown/Black 2? Up 1P Up Brown/White
Wht/Biu | 2P Down IP Down, Blue Red/Bik 2P Down IP Down, Red/White
wht/Gm 2P Left IP Left Violet ‘Orange/Black 2? Left IP Left Orange/White
wht/Yel 2P Right IP Right Yellow. Yellow/Black 2P Right IP Right Yellow/White
wht/Ora Orange Green/Black Green/White
Wht/Red Red Blue/Black Blue/White
Wht/Bm Brown
Gm/wht Biu/Wnt N/A N/A
Yel/Wht Red/Wht N/A N/A
Black Ground
Black Black
Black
<fmlUlofwiu srr fe fs]s]2 jo je joie 5 |> |B] x |> IN] wlolelofel~
Black Ground
Black
Wire color / Stripe color
Wire color /Stripe color <€lalUlalwiu jr{a fe jo] S]Z Jo fo jo |r [D> Bx |> IN wlolejolale
Black
ROMSTAR. inc.
ROMSTAR, INC. 22857 LOCKNESS AVENUE * TORRANCE, CALIFORNIA 90504