Robocop Conversion Kit Installation and Service Manual (780-0111-00)
Robocop (World, revision 4) (Data East Corporation, 1988) · Installation · 11 pages · 17 sections · original scan
N AND SERVICE MANUAL
I By 2 DATA EAST USA. INC. = ‘ J Telephone {408} 286 7080 780-0111-07
CONVERSION KIT
MODEL NUMBER: 1US37K
INSTALLATION & SERVICE MANUAL
TABLE OF CONTENTS
- GENERAL INFORMATION
A. Specific Requirements. ..cccecreuvceserseconesescad
B. List of Materials..csccccccesecnccscrcccseccsoveed
C. Installation Instructions.......scceccerecceseeeed
- GAME INFORMATION
As GAME OPtIONSs v1. 00s ccc csvcecsoccensessrennoenes sO
B. PCB Edge Connector Pin-Out.......ee eee ceeeeeeceeeT
© 1988 DATA EAST USA, INC. 470 NEEDLES DRIVE SAN JOSE, CA 95112 (408) 286-7074
780-0111-00
| 1. GENERAL INFORMATION
. Specific Requirements
The ROBOcoPp™ game is a one or two player video game conversion kit. It is intended to be installed into an existing video game cabinet, and comes with all the necessary components to make the converted game look and play like a new dedicated game!
THE GAME TO BE CONVERTED MUST MEET THE FOLLOWING REQUIREMENTS
MONITOR Horizontal, RGB, negative Composite Sync input
POWER SUPPLY + 5vDC @ 7 amp, +12VDC @ 1 amp
List of Materials
The following items are provided with your ROBOcop™ generic kit. When ordering replacement parts, please be sure to provide the complete description and part number.
ITEM PART NUMBER QTY DESCRIPTION REMARKS o1 036~0158-02 Hrns, JAMMA - GENERIC KIT
| 02 | 180-0024-04 | Pshbtn Assy, W/Microsw, Yellow start | |
| 03 | 180-0024-02 | Pshbtn Assy, W/Microsw, Red | shoot/punch |
| 04 | 180-0024-06 | Pshbtn Assy, W/Microsw, Blue jump | |
| 05 406-0085-00 | Label set, pushbutton ID | generic |
06 406-0003-00 Label, FCC Warning
| 07 450-0014-01 | Joystick, Happ Ctrl, 8 way | w/microswitches |
08 510-0142-00 09 660-0001-00 10 660-0001-02 ai 780-0111-00 12 780-0116-00 13 800-0030-00 14 810-0035-00 15 820-0046-00 16 830-0042-00 PCB set, ROBOCOP Plex, Clear, 23.75 X 7.6 X .125 (for control pnl) Plex, Clear, 24 X 9 X .125 (for marquee) Manual, Instruction, ROBOCOP Kit Manual, Technical Support, ROBOCOP Overlay, Ctrl Pnl, Generic blue DATA EAST ea Underlay, Mon. ROBOCOP ea Decal, Side, ROBOCOP ea Insert, Marquee, ROBOCOP PNPPPRPRPPRPPNNNNE
c. Installation Instructions
When selecting a game to convert, make sure that the Power Supply, the Monitor, and the Coin Acceptors are functional. There is nothing more frustrating than installing a conversion kit and having it not operate due to a faulty Monitor or Power Supply. I know...we will all suspect that the new Logic PCB is defective, right?
It is mandatory that the cabinet be wired to conform with all National and Local Electric Code requirements before the conversion is attempted. The primary section must have adequate noise filtering on the AC line to prevent unwanted conducted radio frequency interference. "Adequate" is defined as a filter with both common mode and differential mode filtering and a minimum current capacity of 2 1/2 amperes.
According to the FCC and other regulatory agencies, every video game must be clearly labeled with the Name and Address of the Original Manufacturer, Date of Manufacture (or serial number), Voltage Rating, Current Rating, Suitability for indoor or outdoor use, and Model Number. In addition, the FCC requires that after conversion, the unit must be labeled with a suitable warning stating that radio frequency interference may result from use in a residential area. An acceptable sticker is included in this kit.
IT IS THE RESPONSIBILITY OF THE PERSON PERFORMING THE INSTALLATION TO COMPLY WITH ALL LABELING REQUIREMENTS.
TAKING IT APART...
Performing a few simple tasks when preparing a game to be converted can save you much time and effort when you are installing the conversion kit.
Find the wiring diagram of the game to be converted! You will need to identify the required DC power supply output wires and the monitor video and sync wires. Note the color coding of these wires or better yet, label them as to their function. This kit contains a new Main Harness, but you will need to splice it into the existing power supply and video wires.
Remove the existing game harness parts that will not be used in this conversion. NOTE: You are modifying only the secondary (DC from power supply) and I/O (video, speaker, and controls) section of the wiring. DO NOT MODIFY OR REMOVE THE PRIMARY AC WIRING. The primary AC wiring has been designed and built to comply with UL and Fcc regulations and must not be altered.
C. INSTALLATION INSTRUCTIONS (cont.)
Remove the original game pcb from the cabinet. Remove all exterior decals, and repair any cabinet damage. Repaint the cabinet if necessary. Remove the monitor plex (or glass). If your plex has silkscreened art work on it, you will need to strip it off, or replace it with a new piece cut to the same size. Using the old Monitor Plex as a template, cut the Monitor Underlay card, supplied with this kit, to the same size as the old plex. NOTE: Be certain that the opening in the Underlay Card lines up with the monitor screen.
Remove the Marquee Plex from the game and use it as a template to cut the new, clear Marquee Plex down to the correct size. Install the Marquee Insert (lexan overlay) to the marquee clear plex, and trim before installing. Remove the control panel from the game and remove all controls and graphics from it. Drill and/or punch any required new holes for the control panel. ROBOCOP™ requires one button for "Shoot & Punch,' and another button for 'jump' control. See the diagram below for a suggested control panel layout. You will also need a 'l player' and '2 player' start button. If you are going to cover the control panel with clear plex (one piece provided with this kit), you should carefully cut it to fit the control panel at this time. Thoroughly clean the control panel so that the new control panel overlay will adhere to it aggressively.
FIGURE 1. Suggested Control Panel Layout
JUMP SHOOT, . SHOOT, JUMP PUNCH PUNCH
ROBOCOP INSTALLATION AND SERVICE MANUAL page 3
Installation Instructions (cont.)
Install the Control Panel Overlay by peeling off the paper backing and carefully laying the overlay down onto the panel. Smooth it out starting in the center and working your way out to the edges, removing all of the trapped air pockets. If possible, cut the edges of the overlay oversize and fold the excess under the panel. cut out the button and joystick holes. Install the Control Function Labels found on the sheet of labels supplied in your kit.
Cover the Control Panel Overlay and Control Function Labels with a clear plex to protect the overlay and labels. Install the buttons and joystick at this time. Mount the completed control panel to the cabinet.
Game PCB: Mount the game PCB set to a convenient wall of the cabinet using the mounting feet and hardware supplied with the PCB.
Pwer Supply Wiring: Plug the Main Harness edge connector onto the Game PCB's edge connector. Separate the DC Power wires and route them through the cabinet to the Power Supply. Try to keep the length of these wires to a minimum for best results. NOTE: Use a minimum of 2 wires EACH for the +5 Volts and the Ground lines between the Power Supply and the PCB. Terminate them at the Power Supply as required.
THE DATA EAST MAIN HARNESS HAS LABELS ON THE EDGE CONNECTOR TO ASSIST IN IDENTIFYING EACH TERMINAL'S PIN NUMBER AND FUNCTION.
Player Control Wiring: Route the Pushbutton and Joystick wires up to their proper destinations, cut to length, and terminate as required.
REFER TO THE EDGE CONNECTOR PIN-OUT ON PAGE 7 FOR WIRE COLOR AND FUNCTION INFORMATION.
c. Installation Instructions (cont.)
Monitor Wiring: The game PCB set has outputs for Positive Red, Green, Blue, and Negative Composite Sync. If your monitor has separate Horizontal and Vertical sync inputs, hook the Composite sync to the negative Horizontal input. This method will work on most monitors; however, some model Electrohomes require that the Composite sync signal be hooked up to both the negative Horizontal and Vertical inputs. Contact your distributor for more information if you are uncertain as to how to hook up the monitor wires.
Coin Door: The Coin Counter(s) may be the 12 volt or 6 volt type as the game PCB utilizes an open collector drive circuit. Hook one coin counter wire to the required voltage (+12v or +5v) and the other wire to the coin counter signal wire from the game PCB.
Graphics: Install the Game Instruction Labels onto the Underlay Card, either in the lower portion, or on one side of the picture tube cutout. Install the Underlay Card under a clear monitor plex (or glass). Mount the new Marquee Plex, and install the Side Decals. NOTE: Install the FCC Warning label to the upper rear of the cabinet.
THE BIG TES'
REMOVE THE MAIN HARNESS EDGE CONNECTOR FROM THE GAME PCB!
Apply power to the game. Measure the +5 volts at the edge connector and adjust to +5.15 VDC using a Digital Multi-Meter. Measure the +12 and -5 vdc wire to be certain they are connected properly and are on the correct terminals. Remove power from the game.
RE-CONNECT THE MAIN HARNESS EDGE CONNECTOR!
Apply power to the game once again. The attract mode video should appear on the secreen. Adjust the picture size and colors on the monitor to get the optimum appearance. Adjust the Sync and Hold controls on the monitor for a stable picture. Coin it up and give it a try! Test all the controls and sound for proper operation.
Congratulations! You have successfully installed your Data East conversion kit! We hope that it gives you many years of successful operation.
- GAME INFORMATION |
‘A. OPERATOR SELECTABLE OPTIONS
The Rosocop™” game allows for operator adjustable pricing, bonus lives, difficulty, etc. These are accessed by the two 8 position dipswitches located on the main logic pcb. Tables 1 and 2 outline the available options.
TABLE 1 - DIPSWITCH 1
ee
| 1 | 2 | 3 | 4 | 6 | 7 | 8 |
| { Game Charge | OFF | OFF | ||||
| (right) | ON | OFF | ||||
| COIN 1 | OFF | ON |
ON ON,
Game Charge OFF OFF t Attract mode OFF i
| (left) | ON | OFF |
| COIN 2 | OFF | ON |
ON ON
| sound? | ON | 1 | |
| Flip Screen? | NORMAL = | ON | | |
| REVERSE: | ies | OFF |
Cocktail Table: = OFF
| i | Upright game: | Se | ON | ig |
TABLE 2 - DIPSWITCH 2
| 1 | 2 | z | 4 | 5 | 6 |
| | Player's | med: | OFF | OFF | ||
| energy | high: | ON | OFF | ||
| | | low: | OFF | ON | ||
| af | very high: | ON | ON | if |
Normal: OFF OFF
Game Easy: ON OFF L Hardest: ON ON J
| Difficulty | Hard: | OFF | ON |
| | | Continue | Yes: | OFF |
| Mode ? | Noz | on | |
| Player's energy in the | High: | OFF | |
| bonus stage | Low: | ON |
B. PCB Edge Connector Pin-Out
The game PCB set uses a 56 pin "JAMMA" standard Edge Connector pinout as shown below in Figure 2.
[ vane COLOR SOLDER SIDE PIN# | PIN# PARTS SIDE WIRE COLOR
| BK | GROUND Al | Bl GROUND | BK |
| BK | GROUND A2 | B2 GROUND | BK |
| RD | +5 VOLTS A3 | B3 +5 VOLTS | RD |
| RD | +5 VOLTS A4 | B4 +5 VOLTS | RD |
| BL | -5 VOLTS AS | B5 . -5 VOLTS | BL |
| OR | +12 VOLTS A6 | B6 +12 VOLTS | OR |
BLOCKING KEY A7 B7 BLOCKING KEY
| vI | COIN COUNTER 2 A8 | B8 COIN COUNTER 1 | sL |
7X) BO
| WH/BK | SPEAKER (-) A10 | B10 SPEAKER (+) | BK/WH |
GN All Bll
| GR | VIDEO-GREEN A12 | B12 VIDEO-RED | RD |
| WH | VIDEO-SYNC A13 | B13 VIDEO-BLUE | BL |
| YL | SERVICE SW. Al14 | B14 VIDEO GROUND | BK |
A15 B15 TEST SW. * BK/GN
| RD | COIN SWITCH 2 A16 | B16 COIN SWITCH 1 | GN |
| RD/WH | 2P START A17 | B17 1P START | BN/WH |
| YL/WH | 2P UP A18 | B18 1P UP | YL |
| GN/WH | 2P DOWN A19 | B19 1P DOWN | GN |
| OR/WH | 2P LEFT A20 | B20 1P LEFT | OR |
| RD/WH | 2P RIGHT A21 | B21 1P RIGHT | RD |
| BL/WH | 2P SHOOT A22 | B22 1P SHOOT | BL |
| VI/WH | 2P JUMP A23 | B23. 1P JUMP | vI |
| PK/WH | NOT USED A24 | B24 NOT USED | PK |
A25 B25 A26 B26
| BK | GROUND A27 | B27 GROUND | BK |
| BK | GROUND A28 | B28 GROUND | BK |
FIGURE 2
uath the its for a Class & comouting device oursuant to Suboart J of Part BS at
case the user, at his own
ROBOCOP Tost oPuTONt (SBS Date Cast Cornoration, Sold exciusivery in the United States of Amenca and Canada
ENVIRONMENTAL DATA
This oroduct Is intersted for use indoor use only, power requirements are ‘OS-I2S volts AC, SO-60 hz, and requires a3 wire grounded outiet.
SERVICE PROCEDURES
pM joer hat cee oh bergen require re or further technical assistance, you
the hours of 8:00 am to 5Sal0 pm Psertic Time at (408)
AAMA WARNING certification label oneach ROBOCOP POS emafackares 107 toeo caine the titan Dhak a ROBREOP PCH that does not "HAMA PROTECT” certification shoud rds not lngah and shouad contact DATG EAST USA, Ne, GF CAGE) cee on
Data East USA. inc. (“Seller”), warrants only to the original purchaser (‘Buyer’). of its
products that the items listed peiow are free trom defects in material and workmanship under nermal use and service for the period specified:
GAME LOGIC PRINTED CIRCUIT BOARD(S)
No other parts of the Seller's products are warranted,
Warranty periods are etfective trom date of inital shipment {'om Seller to Buyer. Seller's sole liabihty shall be, at its option, to repair or replace products which
are returned to Setler dur ing the warranty periods specified, provided:
1. Seller ts notified promptly upon discovery by buyer that
stated products are detective. ly packaged and then returned
- Such products are bs freight pre paid to a place spectiied by Seller.
This warranty does not apply to products damaged during shipment and/or due to improper handing, or due to improper installation or usage, or alteration, tn no event shail Seller be hable for any anucated prefits. loss of profits. loss of use, accidental or consequential dam 5, or any other jaye incurred by the customer In Gonnection with the purchase ef a Data East USA, Inc., product.
psp ony AS SPECIFICALLY PRO ) CONTRACT BETWEEN \BUYER, T ARE NO: ett noe aie pase oh MPL, POR me ares Abr elle