CATHODE RAY TOMES

Space Lords TM-380 1st Printing

Space Lords (rev C) (Atari Games, 1992) · Technical Manual · 84 pages · 78 sections · original scan

Page 1

GAMES

Page 2

_Uyviday e orice guroPe land \ amited set vw

  • Thi is entire: on recyel manud reel nares ab vessstinedt
Page 3

Operator's Manual

with Schematics

A

ATARI

GAMES

Patent is pending on several parts of the Space Lords game

Page 4

INTRODUCTION # SPACE LoRDS

Copyright © 1992 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federai copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95035 Printed in the U.S.A. 9/92 Produced by the Atari Games Technical Publications Department. Writing & Editing: Andrea Dencker Illustration & Design: Mary Ohanessian Sumner NOTICE RE

PARTS

NON-ATARI®

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EM) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end beard is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation, See the inside front cover of this manual for service in your area.
Page 5

Space LORDS INTRODUCTION

SAFETY

SUMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet, If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end. of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation,
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

iti

Page 6

INTRODUCTION % Space Loans

CONTENTS

1 Set-Up How to Use This Manual Operating the Game Inspecting the Game Control and Switch Locations Power On/Off Switch... Volume Control... Self-Test Switch and Bracket Coin Counters. “ Video Display Controls .. Setting the Coin and Game Option Game Play... 13 Introduction . 13 Game Play

2 ~~ «~Self-Test Introduction ... Entering and Exiting the Self-Test 12-2 Strip Lights ..... Select Test Menu Adjust Volume... Statistics ... Statistics Screen. System Error Counts . Remaining Histogram Screens

Sound Board Test. Link Test.. RAM Tests ROM Test . Alphanumeric Test Motion Object Tests . Motion Object Checksums.. Motion Object Growth Test Playfield Tests ... Scrolling Test Stamp Test. Monitor Tests . Video Sync Tes\ Color Test... Purity Test... Convergence Test 3 Troubleshooting and Maintenance

Introduction ... Maintenance Procedures Introduction .. Cleaning Procedure for Coin Mechanisms 3-3 Troubleshooting Procedures . Repair Procedures. Introduction .

Thruster Joysticks Pot Joysticks... System Logic Assemblies.. Video Display

4 Parts Illustrations

Part Ordering Information ve For figure and page numbers, see the list of | illustrations that follows.

5 Schematics

See the list of illustrations that follows.

Statistics Sheet

After the end of this manual

Warranty Inside back cover

Page 7

Space Lorps # INTRODUCTION

Figure 1-1

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16

Figure 4-1

Figure 4-2

Figure 4-3

Figure 4-4 Figure 4-5 Figure 4-6 L USTRATIONS

Main Control and Switch Locations....

Select Test Menu Screen. Adjust Volume Screen, Statistics Screen. Game Options Screen Coin Options Screen Controls Test Screen Sound Test Screen Link Test Screen. RAM Test Screen. ROM Test Screen Alphanumeric Test Screen Motion Object Test Screen Playfield Test Screen Video Sync Test... Color Test Screen........ Convergence Test Screen

Cabinet-Mounted Assemblies,

Pot Joystick Assembly Housing (Body, Pot Joystick Assembly Handle... Over/Under Coin Door and Cash Box.... Over/Under Coin Door and Cash Box, Continued ..... Control Panel Assembly . Power Supply Assembly... Turbo T-Handle Thruster Joystick Assembly... Figure 4-7

Figure 4-8 Figure 4-9

Figure 4-10 Figure 4-11

Figure 5-1

Figure 5-2

Figure 5-3

Figure 5-4

Figure 5-5 Figure 5-6 Figure 5-7

Table 1-1

Table 2-1 Table 2-2 Table 2-3

Table 3-1 Table 3-2 Table 3-3 Space Lords PC/Ground Plane Assembly 4-11 Power Distribution PCB Assembly ... 4-12 JSA3S PCB Assembly (EPROM Version)... CLARN II PCB Assembly Space Lords Game PCB Assembly (EPROM Version) oe

Space Lords Game PCB Assembly Schematic Diagram JSA3S PCB Assembly Schematic Diagram. . CLARN II PCB Assembly Schematic Diagram. JAMMA Filter PCB Assembly Schematic Diagram...

TABLES

Game Specifications .

Summary of All Self-Test Screens ........ 2-2 Game Option Settings . Coin Option Settings

General Troubleshooting.... ROMs and RAMs Troubleshooting Voltage Inputs and Test Points..

Page 8

Inrropuction ¢ Spacr Lorps

NOTES

wi

Page 9

CHAPTER 1

Set-Up

How to Use This Manual

HIS MANUAL IS written for operators and service person-

nel. It provides information for setting up, playing, testing, and maintaining your Space Lords™ game. # Space Lords is a one- to four-player outer-space warfare game that simulates 3D and allows players full navigational control. To maximize earnings, you can link two upright cabinets together so that as many as eight players can compete head-to-head. To do so, a separate link kit is available from your authorized

Atari distributor for a nominal fee. ¢ Chapter 1 of this manual contains set-up and game play information. ¢ Chapter 2 contains a description of the self-test procedures and option settings. The selftest is important in the Space Lords game. You can troubleshoot the printed-circuit boards (PCBs), main circuits, and controls using the screens in the self-test. You should regularly test the boards and controls with the self-test to keep your game in peak condition and at top earnings. ¢ Chapter 3 contains several troubleshooting tables, plus maintenance and repair procedures for the game components. If you have problems with your game, use this chapter to troubleshoot and repair it. Be sure to perform the preventive maintenance tasks to keep your game in good condition. # Chapter 4 contains the illustrations and PCB parts lists. # Chapter 5 contains the schematics for all the PCBs and all the wiring diagrams.

Page 10

Cuarter 1 ~ SE1-Up Space Lorps

Operating the Game

To operate your game for maximum income, you should regularly run the self-test and check the controls with the Control Test and Sound Test in the selftest. By using the self-test regularly, you can find and aracteristi Spe 3.1 Amps at 120 V 4 Amps at 120 V, slow blow 102 to 132 VAC Input Current

Line Fuse Rating Line Voltage ‘ ° ° © to 100° F) fix problems immediately. This lets you keep your Temperature 5° to 38° C (37° to 100° F) game in top condition. Humidity Not to exceed 95% relative Width 53 inches (134.6 cm) G a m Depth 34.5 inches (87.6 om)

Inspecting the e Height* 74 inches (188 cm)

WARNING Weight 580 Ibs. (263 kg)

To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets, Players can receive an electrical shock if the cabinet is not properly grounded. Make note of the power consumption when you set up this game, so that you do not overload your electrical circuit. See Table 1-1 for the power consumption and the other important specifications of this game. Inspect your Space Lords game carefully to ensure that the game is complete and was delivered to you in good condition. inspect the cabinet and seat as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Open the lower rear access panels, Unlock and. open the coin doors. Inspect the interior of the cabinet as follows: a. Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation.

d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly. Check that the green ground wires are connected.

1-2 *Including the woad attraction-sign housing

Table 1-1 Game Specifications

e. Inspect other sub-assemblies, such as the video displays, controls, printed-circuit boards, and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Control and Switch Locations

All of the controls are located on the back of the cabinet or behind the coin doors (see Figure 1-1). The following describes the locations in more detail:

Power On/Off Switch

The power on/off switch is located on the bottom right rear panel of the cabinet, below the right rear access panel.

Volume Control

There is no volume adjustment knob on any PCB in this game. Instead, volume is separately adjusted in the self-test for each side. Refer to Chapter 2 of this manuai for more information.

Self-Test Switch and Bracket

There is one self-test switch, mounted on a bracket behind the right coin door, This self-test switch controls both screens.

Although there is an additional self-test switch located on each GX2 (game) PCB, for convenience we recommend that you use the coin door self-test switch.

Page 11

)

Phaded Space Lorps “ Craprer 1 — Set-Up

PEETIEE oil Coin Counter

Figure 1-1 Main Control and Switch Locations

Coin Counters

The coin counters are located near the bottom of each coin box, inside each coin door.

Video Display Controls

This game provides convenient access to six of the most important video display controls — vertical and horizontal position, vertical hold, vertical size, black level, and contrast. These control knobs are on small PCBs that are mounted on the plywood panel inside each coin door (see Figure 1-1).

Setting the Coin and Game Options

The Space Lords coin and game options are set in the self-test. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This section describes the features and play of the Space Lords game.

Introduction

Man your battlestations! Take a journey among fields of asteroids and gaseous nebulae to the battlefields of the future. Here aliens from across the universe congregate to prove who is the most feared pilot in space.

Page 12

Cnaprer 1 — Set-Up % Space Lorps

Space Lords is a unique engineering feat that allows players a glimpse into the unknown world of space warfare. In a true 3-D universe, game players have full navigational control of their spacecraft. Armed with lasers and nukes, players engage in tactical dogfights with other players and a variety of alien spacecrafts. In a futuristic two-monitor cabinet, one to four players can play either pilot or co-pilot stations. A low-cost link kit is available to link two cabinets together for four-screen, eight-player games. This format enhances the interactive and competitive features of the game.

Game Play

Players can select from three game modes:

  • Solo — Mission-based game. Players must destroy a specified number of alien ships to advance to the next mission. In each mission players face different enemies, requiring different strategies.
  • Team — Players form red and blue teams and compete in a team format.
  • Melee — The ultimate dogfight in outer space. A free-for-all where survival of the fittest is the rule. The pilot’s controls consist of a throttle for speed/direction, flight controller to steer, and a start/hyperspace button. In addition to variable forward/backward positions, the throttle has a rear view button to see behind the ship. Players can fly in one direction, yet shoot in the other. On the flight controller are both laser (trigger/index finger) and nuke (thumb) fire buttons. Lasers are unlimited, unlike nukes. Nukes can be acquired from the “Modify Ship” screen while selecting the game mode, or collected in space through the green bonus satellites. A red Hyperspace button on the control panel serves as a quick escape when the action is getting too intense. The co-pilot, too, has a flight controller and serves as a second gunner, giving the ship double firepower. Like the pilot, the co-pilot also has a hyperspace button, A. special cloaking button makes the ship undetectable by enemy radar. Cloaking, however, consumes energy faster than usual, Pressing both the hyperspace and cloak buttons engages Turbo Cloak, making the ship undetectable and fast. As a bonus to encourage tandem play, the pilot/co-pilot’s ship is awarded extra energy, increased firepower, increased turning ability, an extra life, an extra nuke, and an extra hyperspace.

1-4 In the Game Mode select screen, players have the ability to modify their ship to their specifications. They can adjust any or all of the following: ° Nukes — Long-range high-power weapon

  • Hyperspaces — Quick boost to safety
  • Shields — Protection from enemy blasts and collisions ° Laserpower — Strength of player’s laser
  • Agility — Ship acceleration and responsiveness of the flight control
  • Speed — Top-end speed After getting some experience, players understand how to modify their ship depending on the opponent(s) they face. Eight different alien enemies are in the universe. They include the Troid, Octon, Raptor, Hydrus, Krystar, Xyclops, Nakar and Noptera. Each of these enemies flies unique-looking ships and possesses different flight characteristics. An on-screen radar identifies enemy ship locations. Dots on the screen indicate the location of enemies: the brighter the dot, the closer the enemy. Using a combination of both throttle and flight controller, a player can steer towards or away from a specific ship(s). On the instruction label, a diagram explains how to use the radar. Green satellites in space are good and benefit the player. By collecting these (flying through them), players can collect energy, nukes, hyperspaces, and even an extra life. A ‘?” satellite can award a variety of special bonuses. Players should always collect these when they are easily available. At the top of the screen, a player's “Kills” and “Kill Rating” is displayed. Kills are simply a numerical record of all ships downed by the player, In the Solo/Missions mode, it displays the number of ships left to kill. The Kill Rating is a skill rating based on the number of game credits used. ‘The strip lights go on during game play whenever a player is hit by laser or nuke shots. They are also used in the attract mode to draw players’ attention.
Page 13

CHAPTER 2

Self-Test

SE THE SPACE LORDS™ self-test to

check the condition of the game

circuitry and controls. You will see the self-test information on the video display and hear the sound test information through the speakers. You do not need any additional

equipment to perform the self-test. Perform the self-

test when you first set up

the game, each time you

collect the money, or

when you suspect game

problems. This chapter shows the screens in the

self-test and explains each of the tests. The

screens and explanations are arranged in the order they appear in the self-test. Table 2-1 lists all the self-test

screens.

Page 14

Cuaprer 2 —SetF-Trst % Space Lorps

Entering and Exiting the Self-Test

The game’s self-test switch is conveniently located behind the right coin door. Turning it on causes both screens to enter the self-test mode. Doing so displays the Select Test menu; see Figure 2-1. Exit the self-test by turning off the self-test switch at any time.

Select Test Menu

Adjust Volume

Statistics Statistics System Error Counts Time Per Life for Solo Time Per Life for Team Time Per Life for Melee Session Times

Game Options Coin Options Controls Test

Sound Board Test

Link Test

RAM Tests Video RAM Color RAM Working RAM Common RAM (2) All RAM

ROM Test

Alphanumeric Test

Motion Object Tests Motion Object Checksums Motion Object Growth Test

Playfield Tests

Scrolling Test Stamp Test Monitor Tests Video Syne Test Color Test Purity Test Convergence Test

Table 2-1 Summary of All Self-Test Screens

Strip Lights

When the right-hand side is anywhere in the Select Test menu, both lights should be on. When the righthand side enters a specific test from the Select Test menu, both strip lights should be turned off. The strip lights go on during game play whenever a player is hit by laser or nuke shots. They are also used in the attract mode to draw players’ attention.

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Note that this picture shows the full test selection screen, which only appears on the right video display in each game. The left display shows fewer tests. Therefore, the right display acts as a “master” self-test screen. Move up and down the menu by moving the left joystick forward or backward (or by pressing the thumb button). Start the selected test by pressing the tigger button.

SELECT TEST

Figure 2-1 Select Test Menu Screen

Adjust the volume of the game using this screen, shown in Figure 2-2. Follow the instructions at the bottom of the screen to change the volume, to restore the old volume level, and to save the new volume and return to the select test menu.

Page 15

Space Lorps % CHApTER 2 — SELF-TesT

ADJUST VOLUME

VOLUME: 3

Move Joystick to ADJUST volume Press Throttle Button to RESTORE oid Setting Press Thumb Button to SAVE setting and return to menu

Figure 2-2 Adjust Volume Screen

Statistics

Use the information shown in the statistics and histogram (bar graph) screens to keep track of your game use and maximize your profits. Record the information on the Space Lords statistics page in the back of this manual. The first of the screens is shown in Figure 2-3. (Make several extra copies of this form before writing on it!) The game statistics are collected from the last time the statistics were cleared. Follow the instructions at the bottom of the screen to clear the statistics or to advance to the next statistics or histogram screen.

STATISTIC. Loft Cot 2128 Right Coins

Copitot Coins. New Games Continue Games Error Count

Total Coins

Tor mare stais

Figure 2-3 Statistics Screen Statistics Screen

The statistics screen lists the following information:

  • Left Coins shows the number of coins counted in the left coin mechanism. ° Right Coins shows the number of coins counted in the right coin mechanism.
  • Idle Minutes shows the number of minutes that the game was idle and not being played. ¢ 1 Player Minutes shows the number of minutes that the game was played by one player only. ¢ 2 Player Minutes shows the number of minutes that the game was played by two players.
  • Solo Minutes shows the number of minutes that the game was played in solo mode (a mission-based game).
  • Team Minutes shows the number of minutes that the game was played in the team mode.
  • Melee Minutes shows the number of minutes that the game was played in the melee (free-for-all) mode. ¢ Pilot Coins shows the number of coins counted in the left mechanism of each coin door.
  • Copilot Coins shows the number of coins counted in the right mechanism of each coin door.
  • New Games shows the number of unique games played. A unique game is counted every time a player starts a new game (not a continued game),
  • Continue Games shows the number of games that players continued.
  • Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 13C on the Space Lords game PCB. ¢ Total Coins shows the number of coin accumulated by the game in all coin slots.
  • Average Time per Coin is displayed in seconds. This is tabulated for all games played since the statistics were cleared. If there are no credits, this line will not be displayed.
  • Percentage Play shows the percentage of time played vs. the total time the game was turned on.

System Error Counts

This screen shows several important statistics regarding system errors. You should have zero or near zero shown after all numbers.

Page 16

Cuaprer 2 - Seur-Trst Space Lorps

Remaining Histogram Screens

The remaining four screens show time per life for solo, time per life for team, time per life for melee, and session times. The first three of these screens show the number of games played, grouped in 30-second increments, but the session times are shown in minutes. The bottom of each screen shows the median game time for that mode. The median value means half the games were above that value and half below.

Game Options

Check and select the game options on this screen, shown in Figure 2-4. The screen shows the factory default settings in green. To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The game options, with defaults, are shown and explained in Table 2-2. GAME OPTIONS

Game Difficulty dium

Pifot Lives to Start?

ti for Continue?

Figure 2-4 Game Options Screen

Coin Options

Check and select the coin options on this screen, shown in Figure 2-5. The screen shows the factory default settings in green.

Explanation

Sets the game difficulty for both the left and right screens.

Opt Available Settings

Difficulty Level O-Easiest ...7—-Mediumv ... 15 — Hardest

Pilot Lives to Start? ilifev 2lives Slives 4 lives Determines how many lives are granted whenever a game is started. Pilot Lives for Continue? 1 lifew 2lives 3lives 4 lives Determines how many lives are granted whenever a game is continued.

Determines how many lives are granted whenever a game is started.

Determines how many coins are required to start a co-pilot game Copilot Lives to Start? 1 lifew 2lives 3lives 4 lives

Copilot Game Cost? 1coinw 2,3, 4,5, 6, 7, 8coins

Station Colors? Red & Green Ww Blue & Yellow Red & Green are the default colors of the players’ spaceships on the screen. If you link two games together, set this option to Blue & Yellow on the second linked game.

Attract Music Frequency No MusicFrequent ¥Lets you turn the sound off in the attract mode, or adjust how

Less Frequent Very Frequent often the attract music plays.

Auto High Score ResetYesvNoAutomatically clears the high score table periodically.
Reset High Score Table? Yes VvNoClears the high score table the next time you select the

game mode.

Restore Factory Default? YesNowReturns all the game options to the green factory defaults.

Vv Manufacturer's recommended settings Table 2-2 Game Option Settings

2-4

Page 17

Space Lorps # CHAPTER 2 — SELr-Test

COIN OPTIONS

Free Play: No Discount to continue: Yes

Game cost: 2 coins 1 credit Bonus for quantity huy-in: None

Right mech value: 1 coin counts as 1 coin v more ¥

RE Press Thumb and Tr to SAVE setting and return to menu

Figure 2-5 Coin Options Screen

To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The coin option settings, with defaults, are shown and explained in Table 2-3.

Option Available Settings

Free Play Now Yes

Controls Test

NOTE The coin switches are checked in the Sound Board test. See the section that follows in this chapter.

The control test screen is shown in Figure 2-6. This test checks all the pushbutton switches, the joystick potentiometers, and the throttle switches. As you use each control, the numbers for the joystick pots increase or decrease, or the switch names are highlighted. If the changes do not appear on the screen, check the controls and their wiring. Follow this procedure:

  • Simultaneously press the trigger and thumb buttons to reset the joystick pot limits; the center numbers will turn ced. Then push the joystick into the four corners to set the maximums and minimums. Make sure that the green numbers correspond to the changes. The upper left corner corresponds to the lower numbers.

Explanation

Lets you choose free play to demonstrate the game. Discount toContinue No Yes¥ When set to Yes, this option reduces by 50% the player's cost to continue a game (always rounded up to the next full coin). Game Cost 1 coin 1 credit 2 coins 1 credit

8coins 1 credit The number of coins required for one credit.

Bonus for Quantity None / Buy-in 2 coins give 1 3 coins give 1 3 coins give 2 4 coins give 1 9 coins give 2 9 coins give 3 Lets you choose from various kinds of bonuses or no bonus.

1 coin counts as 1 coin” 1 coin counts as 2 coins Right Mech Value

1 coin counts as 7 coins 1 coin counts as 8 coins The number of coins each coin counts as in the right coin mechanism.

Left Mech Value —_{ coin counts as 1 coinW 1 coin counts as 2 coins

1 coin counts as 7 coins 1 coin counts as 8 coins The number of coins each coin counts as in the left coin mechanism.

v Manufacturer's recommended settings

Table 2-3 Coin Option Settings

2-5

Page 18

CuapTer 2 — SeLr-Test Space Lorps

If the center numbers stay red as you move the joysticks into the four corners, this indicates the pois do not have enough range. If the minimum and maximum numbers are too close to zero or too close to 255, then the minimum and maximum numbers are displayed in red.

ine pots should be replaced if any numbers stay

red.

  • Press each button on the control panel. Make sure that the corresponding message is highlighted on the screen.

CONTROLS TEST

BLUE Button Left Thumb Left Trigger ‘Throttle Forward Throttle Button RED Button Right Thumb Right Trigger Throttle Reverse RIGHT of DOUBLE DOUBLE SYSTEM

Left Joys Right Joystick: B4 78 BA

ind Press Thumb Button to RESET Joystick Limits Press Thumb Button to SAVE setting and return to menu

Figure 2-6 Controls Test Screen

Press the left thumb button to return to the select test menu.

Sound Board Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-7.

NOTE The Audio PCB must be installed and connected in the game to perform this test.

To select a sound, to play a sound, or to return to the select test menu, follow the instructions shown at the bottom of the screen. (You can have numerous sounds playing simultaneously, or you can have silence, depending on which ones you select.) Pressing the throttle button will stop all sounds.

2-6 SOUND TEST

4 5

SOUND #4 $04 MUSIC CHIP TEST Press Trigger button to START sound Use Joystick to SELECT Sound

NUMBER OF SOUNDS § : 253 SOUND CPU STATUS GOOD

COIN MECH SWITCHES: LFT RGT LFT RGT 0 oOo o oO Press Thumb Button to return to menu

Figure 2-7 Sound Test Screen

Verify that the Sound CPU status is good. Also press the left and right coin mechanism switches: the 0 on the screen should change to a J while you press the corresponding switch. Note that the leftmost group of LFT and RGT coin mech messages will be displayed only if you have linked two cabinets together.

Link Test

The link test checks the link between two Space Lords games (see Figure 2-8).

LINK TEST 00 00 09 00 00 00 FF FE FF FF FF FF 24 22 23 24 2 01-02 03 04.05 NO sending STATION: YBGR NETWORK YBGR NEIGHBOR: YEGR

TRANSMITTED NOT SENT TOTAL NOT SENT ‘LOST TMAS:

RECEIVED :

REPEATS: Pross Trigger Button to CHANGE sending mode, Press Thumb Sutton toreturn tomenu

Figure 2-8 Link Test Screen

Once both linked games are in the Link Test, START “ASYNCHRONOUS SENDING” by pressing the pilot trigger on each cabinet. The most important numbers

Page 19

Spacr Loxps % CHaprer 2 — SELF-TesT

to look at are TOTAL NOT SENT and TOTAL LOST. Both of these numbers should be zero or a very low number, and should not be increasing,

NOTE A link problem can remain hidden and unsolved if you do not check both linked cabinets.

If incorrect data is received in any of these cable tests, the failure will appear in red. You may have a problem. with the cable, plug, harnesses, or connectors.

NOTE Do not run this test if a connected/linked game is not in Self-Test.

RAM Tests

Use this selection screen, shown in Figure 2-9, to run any of the six RAM tests. These tests check the RAM chips in various ways.

RAM TEST

Video RAM (looping) Color RAM (looping) Working RAM (looping) Common RAM (looping) Common RAM (READ looping) All RAM (re-start)

EXIT RAM TESTS

Figure 2-9 RAM Test Screen

ROM Test

Use this selection screen, shown in Figure 2-10, to see if the ROMs are OK. When you turn on the power, the game automatically runs through the random-access memory (RAM) and read-only memory (ROM) test. Regardless of whether or not the game has a problem, it will always advance to the atiract mode. The game will stop only if you power it up and the self-test switch has been previously turned on.

ROM TEST

AIP AOHs ate GK

os: fisePi992. 02:18:12 MAIN: 11SEP1992 18:55:53

Press Thumb Button to return to menu

Figure 2-10 ROM Test Screen

If the test finds no ROM errors, no message appears and the program goes to the title screen in the attract mode. If a ROM fails, a message may be displayed. However, the program may be unable to show the location of the failed ROM. The ROM error message will stay on the screen for ten seconds. If you think you have a ROM error, but the screen shows no messages, check the ROMs at 23E, 23J, 37E, and 37J on the Space Lords game PCB. Check these locations for bent pins or incorrectly inserted chips. Also see Table 3-2 for information about the locations of the ROMs and their functions. Depending on how bad the ROM error is, you may not be able to enter the self-test.

Alphanumeric Test

The alphanumeric test, shown in Figure 2-11, checks the condition of the alphanumerics in the game. If you see an error in the alphanumerics or graphics on the screen, check the EPROM at 13N on the Space Lords game PCB. To page (scroll) the screen up and down, or to return to the select test menu, follow the instructions shown at the bottom of the screen.

Page 20

Cuapter 2 — Seir-Test Spack: Lorps

ALPHANUMERIC

Figure 2-11 Alphanumeric Test Screen

Motion Object Tests

Motion Object Checksums

The first motion object test screen, shown in Figure 2-12, examines the checksums of the motion object ROMs. If the checksums match, All Motion Object ROMs OK is displayed. If the checksums do not match, either you have a defective EPROM/ROM or a chip may be installed incorrectly.

Motion Object Growth Test

The second motion object test screen shows two squares; one grows to full-screen size, while the other shrinks. Use the left joystick to control the rate of growth of these squares. Make sure the growth is smooth; any tearing of lines or pixels and/or inconsistent colors indicate a problem with the motion object circuitry.

MO CHECKSUM TEST

MOTION OBJECT ROM ‘CHECKSUM ERROR CHECKSUM ts SHOULD BE 6AFS OBES

39h, 39T OBEO © OACt 35R, 357. SE7C ERA

Press and hold thumb button to return to menu

Figure 2-12 Motion Object Test Screen

2-8

Playfield Tests

The playfield test screen, shown in Figure 2-13, tests the movement of the playfield.

Scrolling Test

To scroll the playfield continuously in a horizontal or vertical direction, move the left joystick in the corresponding direction. Make sure that the playfield screen is clean and scrolls smoothly across the screen.

Stamp Test

To view the playfield stamps, move the joystick forward/backward.

OABEARGTSIARCH SEES

Figure 2-13 Playfield Test Screen

Monitor Tests

This test has four screens. Advance to each screen to completely test the monitors.

Video Sync Test

NOTE Do not run this test if a connected/linked game is not in Self-Test.

This test is useful for both linked and single Space Lords game cabinets. The video sync test (see Figure 2-14) checks that both games are synchronized. Make sure that all screens in your system are displaying this test; then check the positions of the four blocks on the screens. They should not drift from the correct posi-

Page 21

Space Lorps CHaprer 2 — Seur-Trst

tions, which are shown in Figure 2-14. All blocks should be close to the same height. If the blocks on one screen are not in the same position as on the other screen or the blocks are drifting, you could have two causes for this problem. The CLARN II PCB could be bad, or the link harness or related connectors on it could be defective.

VSYNC TEST

Press Thumb Button to return to menu

Figure 2-14 Video Sync Test

Color Test

The color test (see Figure 2-15) indicates the dynamic range of the video display color circuit. The screen should show three bands (red, green, and blue) plus white in the right half, ranging from black to white, from left to right. The red, green, and blue bands are produced by only one color gun being turned on in each band.

COLOR TEST

Press Thumb Button to return to menu

Figure 2-15 Color Test Screen

Purity Test

The next five screens are color purity tests. The entire screen will be red, green, blue, white, and grey. Press the trigger on the left joystick to change colors. Each screen should show no unevenness of color and no lines in the display.

Convergence Test

The convergence test has three screens — white, violet, and green backgrounds with grid lines. The white screen is shown in Figure 2-16. To see the remaining screens, press the trigger button. Press the thumb button to go to the select test menu,

Figure 2-16 Convergence Test Screen Check the following on the screens:

Page 22

Cuapter 2 - Setr-TEst “ Spack Lorps

  • The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel. *
  • The convergence of the lines on the violet and black screens should be within 2.0 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manual. Return to the select test menu by pressing the thumb button.
Page 23

CHAPTER 3

Troubleshooting

& Maintenance

  • HIS CHAPTER contains maintenance,

troubleshooting and repair procedures for

your Space Lords” game, The mainte-

nance section gives informa-

tion on cleaning the parts.

The troubleshooting section

contains several tables to help

determine the source of a

problem and the steps neces-

sary to repair it. The repair

section contains the steps nec-

essary to remove and install

the serviceable parts. Togeth-

er, these three sections provide a complete guide to

servicing your Space Lords” game.

Page 24

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE % Space LORDS

Problem iggested Action

Coin Mechanism Problem

  • Check the wiring connections to the coin mechanism.
  • Check the voltage to the + side of the mechanism.
  • Test the coin mechanism with the Sound Test screen in the self-test. . 4, Check the power distribution board fuses.

Joystick or T-Handle Thruster Joystick Problem . Has the control been lubricated with the correct type of lubricant? If not, lubricate it as shown in Figures 4-2 and 4-6.

  • Check the harnesses and connectors.
  • Check the switches on the control,
  • If you took the control apart, have you reassembled it correctly?
  • Make sure all the parts of the contral are in good repair. Repair or replace parts as needed,
  • Reset the limits on the joystick using the Controls Test in the self-test.

Pushbutton Switch Problem

Check the switch using the Controls Test in the self-test . Check the wire connections and solder joints to the switch. Check the switch for continuity using an ohmmeter. Replace the switch only if it is bad. Bona

Sound Problem Check the speaker volume seiting. Check the voltage on the PCB edge connector. Check the connections from the PCB to the speakers. Check the voltage level to the PCB. Check the sound ROMs in the Sound Board Test of the self-test procedure. Check the resistance of the speakers for 8 Ohms. Replace the speaker(s) only if bad. NOARONMS

Video Display Problem

Screen is dark Check to see that the game is plugged in. . Check to see that the game is turned on. Check the line fuse, Check the display brightness. Check the solder connections on the line filter and the transformer. Check the edge connector to the PCB. Check the harnesses and connectors to the video display PCB. Check the voltage levels to the video display PCB. Run through the following checklist. If you answer no to any question, you have a problem with the video display, not with the game circuitry. In this case, refer to your video display service manual a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have the correct voltage to the video display? tPPrprgy SONOA BONS

Attemptto run a cornplete RAM/ROM test in the self-test. . Replace tne RAM. Only a colored screen appears Pst

Display area wavers or is too small . Check the voltage levels to the video display PCB. Check the B+ to the video display. (Refer to the video display manual.) po

Strip light problem Check the bulbs in the strip light. Check the Power Distribution Board fuses. . Test the strip lights in the self-test. ota

Table 3-1 General Troubleshooting

Page 25

Space Lorps @ CHAptER 3 — TROUBLESHOOTING AND MAINTENANCE,

Problem Suggested Action

Picture is wavy1.Check the connection of the monitor ground wire to the monitor.
  • Check the connections of the sync inputs.
.Picture is upside down or reversed1.Switch the horizontal or vertical yoke wire connections to the video display.
Convergence, purity or color problems1.Use the self-test mode to digitally adjust the video display.
  • Use the adjustment procedures in your video display manual
‘Picture is not centered1.Use the centering procedures in your video display manual

Electronic Game Link Problem 1, Check the harnesses and connections between both games.

Table 3-1 Generai Troubieshooting, Continued

M aint enance 1. Open the upper coin door.

  • Open the gate on the door that covers the magnet.

Troubleshooting Procedures

Use the blade of a screwdriver to scrape away any metal filings that have collected on the magnet.

  • Clean the loose dust and dirt from the coin mechanism Introduction with a lint-free rag or a soft brush. This section describes the maintenance procedures for all 4, Clean the dirt and residue from the coin path with a of the major assemblies and components of the game. The toothbrush. Hot, soapy water may be used to help dismaintenance procedures should be performed every 3-4 solve dirt and residue. months on a regular basis. 5. Blow out all the loose dirt and dry the coin mechanism with compressed air.
WARNING 6. Close the gate on the door that covers the magnet and Before performing any maintenance or repairs, please observe ail of the following safety precautions:
  • Turn the game's power off.
  • Unplug the power cord from the electrical socket.
  • Secure loose clothing such as ties and long sleeves that could get caught within the game. 4, Remove all metal jewelry such as watches and necklaces that could conduct electricity from the game's power sources. close the upper coin door.
CAUTION Never lubricate the coin mechanism with oil or grease.

This section is designed to help determine the source of a malfunction and detailed information on repairing the problem.

Cleaning Procedure for Coin

Mechanisms

Regular use of the coin mechanisms may result in a buildup of residue and dirt. If this is the case, clean the coin, mechanism by following the steps below (refer to Figure 4-5 and Figure 4-6 for detailed part information on. the coin door). Table 3-1 General Troubleshooting, is divided into two columns. The left-hand column is broken down into the general nature of problems. The right-hand column lists suggested solutions to solve the problem.

Page 26

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE @ SPACE LORDS

Table 3-2 ROMs and RAMs Troubleshooting, is designed to help determine the specific ROMs and RAMs that are the source of a game logic malfunction. The left-hand column shows some problems that may result from malfunctioning ROMs and RAMs. The middle column shows the ROMs and RAMs that may be the source of the problem and their purposes. The right-hand column shows the PCB locations of the ROMs and RAMs that may be causing the problem. Table 3-3 Voltage Inputs and Test Points, is divided into three columns. The left-hand column shows the correct voltages that should be measured. The middle column shows the physical locations of the test points or LEDs. The right-hand column shows the sources and purposes of the voltages.

Repair Procedures

Introduction

This section describes the repair procedures for all of the major assemblies and components of the game. Before performing any repairs, use the tables in the Troubleshooting Procedures section to help narrow the source of the problem. The Maintenance Procedures section may also provide a good starting point for fixing many game problems before beginning what might be unnecessary repairs.

Speakers

Each game has two speakers, one for each side. The speakers provide the music and sounds for the game and self-tests. Failure of the speakers may result in distorted or no sound. If this is the case, replace the speakets by following the removal and installation steps below.

  • Remove the attraction shield and decal by removing the retainers that secure them,
  • Disconnect the harness to the speaker,
  • Remove the four screws and washers securing the speaker housing.
  • Disconnect the hamess from the speaker; then remove the four screws securing the speaker.
  • Replace and reinstall the harness speaker.

Strip Lights

To replace the strip light bulbs, follow the removal and installation steps below. 1, Remove the plastic attraction panel ai the top of the game cabinet by removing the retainers that secure it.

  • Unfasten the screws that retain the strip light brackets. on top of the cabinet.
  • Lift the strip light bracket out of the slot on top of the cabinet and disconnect the harness to the PCB assembly. 4, Rotate the bulb 1/4 turn (90 degrees) in the lamp clips and remove it by pulling on the bulb.

Thruster Joysticks

To replace the microswitch on either T-handle thruster joystick, disconnect the wires to the switch on the joystick (see Figure 4-6). Remove the screws that hold the switch on the joystick. Remove the switch.

Pot Joysticks

The pot joystick and its handle are shown in Figure 4-2. If you want to repair the joystick control, disassemble it by removing it from the control panel. The hardware that secures the joystick assembly to the control is listed in Figure 4-4.

System Logic Assemblies

This section describes the repair and maintenance procedures for the major assemblies and components that are related to the system’s logic and electronics, including the printed-circuit boards (PCBs) and the power supply. These components are housed in the bottom of the cabinet below the video display. Space Lords Game PCB Set The Space Lords game PCB set is responsible for the display graphics and game play. Failure of the game PCB set may result in erratic or no game play. If this is the case, repair or replace the game PCB set by following the removal and installation steps below.

  • Unlock the right rear access panel of the cabinet (as you view it from the rear) and remove it. 2, Disconnect the harness connectors from the game PCB set.
  • Unfasten the screw and spacer that secures the game PCB set to the cabinet. Remove the game PCB set and its attached cover (refer to Figure 4-7).
Page 27

SPACE LORDS @ CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE,

CAUTION Before handling static-sensitive componenis, properly ground yourself to discharge buildup of static charges.
  • Re-install the game PCB set by following the previous steps in the reverse order.

Electronic Game Link

Each Space Lords game is linked internally. Electronic game fink connector are available to electronically link two Space Lords game cabinets together for up to eightperson play. Damage to the electronic game link connector may cause the eight-person play to function incorrectly or not at all. If this is the case, replace the electronic game link connector by following the removal and installation steps below.

  • Unlock the rear access panel of the cabinet and remove it,
  • Disconnect the external game link cable from the game link connector.
  • Remove the ground plane hat and disconnect the link connector from the CLARN II PCB.
  • Unfasten the 4 screws that secure the game link plate to the cabinet and remove the game link connector and attached plate.
  • Instali the new game link connector by following the previous steps in the reverse order.

Power Supply The power supply is responsible for providing power to all of the game assemblies that require it. Failure of the power supply may result in erratic game play or no power at all. If this is the case, repair or replace the power supply assembly by following the steps below.

  • Unlock the rear access panel of the cabinet and remove it.
  • Disconnect the wiring harnesses from the power supply.
WARNING The power supply can contain high voltages even after the power is turned off. To avoid injury, observe ail of the safety precautions before working on the power supply. (Refer to the Introduction in the Maintenance Procedures section.)
  • Unfasten the 4 screws that secure the power supply assembly to the cabinet, and remove the power supply assembly.
  • Re-install the power supply assembly by following the previous steps in the reverse order.

ROMs/RAMs The ROMs and RAMs contain the programming routines used by the game PCB set to control game play. Refer to Table 3-2 ROMs and RAMs Troubleshooting to determine the ROMs or RAMs that are malfunctioning. Replace the damaged ROMs or RAMs by following the removal and installation steps below.

  • Remove the game PCB set according to the procedure in the Space Lords Game PCB Set section.
CAUTION Before handling static-sensitive components, properly ground yourself to discharge buildup of static charges.
  • Remove the damaged ROMs and RAMs from the game PCB set using a chip extraction tool.
  • install the new ROMs and RAMs by plugging them in the game PCB set sockets, 4, Re-instail the game PCB set by following the steps in the Space Lords Game PCB Set section in the reverse order.

Video Display

To repair, replace or make adjustments to the video display, follow the removal and installation steps below.

Page 28

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE “ Sack LORDS

Problem ROMs/RAMs Source and Purpose ocation

ROMs

The program works, but the motionMotion Object ROMs (responsible for moving graphic31L, 31N, 31R, 31T,
objects are incorrect or non-existent,objects)33L, 33N, 33R, 33T,

38L, 35N, 37L, 37N

Garbage appears on the screen orProgram ROMs (responsible for game control)23E, 23J, 37E, 37J

game play doesn't work correctly.

The text or numbers are incorrect or Alphanumeric ROM (responsible for controlling

non-existent.graphic text and numbers)13N

The sound is incorrect or non-existent. Audio ROMs (responsible for controlling sound) Audio Program ROM 18E Audio ADPCM ROM 5A

The moving backgrounds graphics are Playfield ROMs (responsible for controlling background

incorrect or non-existent.graphics)2D, 5D

RAMs

The display color is yellow. Working RAM

The display color is green. Video RAM

The display color is white. Color RAM

Table 3-2 ROMs and RAMs Troubleshooting

VoltageTest Point or LED LocationVoltage Source and Purpose
+54 0,25 VDC+5V1Logic power from the switching power supply.

CRi LED (GX2 or game PCB) Lights when § V is applied to the PCB and the reset (RST) jumper is open.

CR1 LED (JSA3S PCB) Lights when the +12 V supply is good.

CR2 LED (JSA3S PCB) Lights should be out (connected to ground)

CR1 LED (CLARN II PCB) Lights when left GX2 is powering CLARN Ii +5V

CR2 LED (CLARN II PCB) Lights when right GX2 is powering CLARN I! +5V

CR3 LED (CLARN 1! PCB) Blinks to indicate which CLARN II is video sync master.

+12V+VOP (pin 4 of LM324)+12 V from the switching power supply. Positive supply for

the analog circuitry.

-5V-VOP (pin 11 of LM324)-5 V from the switching power supply (if connected). Nega-

tive supply for the analog circuitry (connected to ground).

Table 3-3 Voltage Inputs and Test Points

Page 29

Space Lorps % CHAPTER 3 ~ TROUBLESHOOTING AND MAINTENANCE

WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation This video display is designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube (CRT) may implode if struck or dropped. The shattered glass from the tube may cause injury up to six feet away, Use care when handling the display and when removing it from the game cabinet. Also, wear gloves to protect your hands from the sheet-metal edges.

. Unfasten the 8 square drive screws that secure the monitor doors to the cabinet and remove them. . Discharge the high-voltage from the cathode-ray tube (CRT).

NOTE The label on the video display assembly shows a circuit for discharging the high-voltage contained in the CRT to ground when the power is off. a. Secure one end of a solid 18-gauge wire to a wellinsulated or wooden handle screwdriver. b. Secure the other end of the wire to an earth ground. c. Briefly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait 2 minutes and repeat the previous step. . Disconnect all of the wire harnesses from the video display. . Unfasten the 13 square drive screws that secure the light housing assembly and remove it. . Unfasten the 10 square drive screws that secure the lower glass retainers. Remove the display shields and card-board bezels. . Unfasten the 4 flat washers and nuts that secure each video display chassis to the cabinet monitor mounting brackets. Remove the video display assembly from the cabinet.
NOTE Do not attempt to remove the video display without its chassis.

. Install the new video display by following the previous steps (excluding steps 2a.—2d.) in the reverse order.

  • If necessary, adjust the new video display’s brightness, size, centering, purity and convergence according to the video display service manual.

3-7

Page 30

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE * SPACE L

Page 31

CHAPTER 4

Parts Illustrations

Part Ordering Information

HIS CHAPTER provides information you need to order parts for your game. The printed-circuit board (PCB) parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by part number. When you order parts, give the part number, part name, the number of this manual, and the serial number of

your game, With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari

Games Customer Service phone numbers are listed on the inside front cover of this manual.

Page 32

Cuarrer 4 — Parts ILLUSTRATIONS % SPACE LORDS

05110%-01 Strip Light Bracks ASS (2 places) 476015112 05114501 0-914" Pana Red Strip Light Plex ‘Tapping Screw @ places) (places) 05114801 White Detuser Plex @ places)

051144-01 Altraction Shiold 051153-01 Attraction Decal

osre74.o1 Cleat (2 places) 176020-220 #8x1 114" X-Rec Screw (6 places)

051109-01 Left Bezet 178056-002 12x 1/16 Foam Tape ‘{t" Strip, 6 places) '051108-02 Right Bezel

051140-01 Display Shiels (2 places)

051141-01 Center Shield Retainer 1783480108 50 W. x 0327. Foam Tape

(Not Shown inthis drawing)

(places)

051187-01 PilovCo-Pilot Decal (2places)

051108-01 Coinage Label | —- (2 places)

1171093-001 or 171095-001 ‘OvertUnder Coin Door places) (03815301 (-05) Product LD. Label

051085-02 Seam-Covering Decal (2oiaces) 051143-01 Attraction Retainer (2 places) 476037-4016 #1024 x 1.00" Tampe. Prool But: Hd. SO" a7g99g,991 (apiece 12s, 1aW Flores Ug #10 Flat Washer Ua aoell i places) 18" Fluorescent Lamp Fixture f 178322-001 Lamp Retainer Ctip @ places) = 176015-110 WO x8" Xlec., Pan-Hd, “Tapping Serew (2 places)

6a)

Figure 4-1 Cabinet-Mounted Assemblies, Front View F 051132-01 Alraction Cap (2places} 1176010-220 8.x 1 1/4" Sq-Dr. Screw (4 places)

(051142-01 Loft Shiold Rotainer 051142-02 Right Shield Retainer 176019-212 #8 x 9/4" Sq, Dr. Screw (places) 178263-0402 25 Ex 1257. Foam Tape

(8049286-01 Tost Switch Assy. 176015-110 10 x 6/8" Pan-H., ‘Tapping Screw

051156-01 Instructions Decal (2 places) | 05110301 ii Panel Assy. 72-5520 4420 x1 118" Hox Hd. Sorew (3 places) _| 475014-1050 414" Flat aster places) ‘76057-4410 114"-20 Tamper Proot, Bute-He, Serew places) 475014-3050 1/4" Flat Washer (2 places) 051073-01 Lett Speaker Enclosure (051073-02 Right Speaker Enclosure 175014-1050 1/4" Flat Washer (6 places) 72-5520 114-20 1 1/4" Hex-Hd, Screw (8 places) | 051149-01 Speaker Grille (@places) ‘A050874-01 Spesker Hamess Assy. (2 places) 1148007-104 4412" Dia. ‘Speaker (2places) 17026-0040 10-24 Nuy’ Washer Assy. (8 places)

Page 33

Spacr Lops @ CHaprer 4 — Parts Litusrratrons

Items Not Shown:

051102.01 Wood Verrior Kt List 05067101 Main Hamoss Assy ‘4050672-01 ‘Speakers/Atration Hamess Assy 14050398-01 Power Hamess Assy 150081-001 Power Sunply Cord Tw-300 25" Wells Gardner, Std.-Res. Dispiay Senco Manual TM.320 Operators Manual 7126-002 5/82 Tampor Broo Brver 17e028-001 Tox key Diver 051106-01 Poster

03815801 (-10) Product ID. Label |

038158-01 (03) Product .D. Label

.8051099-01 POIGroundplane Assy. 1036158-01 (07) Product LD. Label 175008-002 Nylon Washer “76015-112 0x94" Pana, Tapping Screw

72.6608S 26x 1/2" Type AB, Pan-Hd. Sorow (4 places, 2 for each PCB) 175004-706 Flat Washer (4 places, 2 for each POB)

A050824-02 Power Distribution PCB Assy. 178265-001 L:style Nylon Stand-off (4places) 7266088 #6x 112" Type AB, Pan-tid. Screw (4 places) Hardware for ‘mounting monitor: adjusting PCB,

(8050680-01 Power Supply Assy. 176015-112 #10-9/4" Pan-Hd,, “Yapping Screw (4 places) 17026-0038 #8-32 NuvWasher Assy. 051155.01 Right Side Decal 051155-02 Lett Side Decal 199022-401 25* Color Display (2 places) (638158-01 (-07) Preduct .D. Label 725516 174-20 x 1,00" Hox-H, Bolt (8 places) 17016-0125 414 Ext. Look Washer (@ places)

099450-01 FCC Compliarce Label

042452-01 FBI Warning Label

ost121-01 Cabinet Door places) —| 038086-01 ‘Shock Warring Lebel (2 places; ¥76019-220 #8x 1 14" Sq-Dr Serew (6 places)

| 051121-01 Cabinet Door (2 places) 3086-01 ‘Shock Warning Label (2 places)

112! Staple (6 places)

|| 05115801 4 Amp Fuse Label A050348-02 4.Amp ONOFF ‘Switch Assy. 1176003-108 4 x 172" Rec, Pan-Hd. Sorow (2places) 4¥78089-001 Fon-Guard (2 places)

043999-01 Leg Leveter Piato (4 places) Wood Cabinet

778023-001 4" Dia. Rubber Caster (6places)

Figure 4-1 Cabinet-Mounted Assembiies, Rear View A051100-01 F

Page 34

CHAPTER 4 — PARTS ILLUSTRATIONS % Space Lorns

119008-1001 Potentiometer

99-215060 Pot Mounting Plate| (2 places)

‘Wires go through the nut, ball bearing, and the spacer into the Joystick shaft, !

4-4 99-215087/ Follower’

99-215055 Spacer|

99-215054 Ball Bearing

99-215053 Nut & Hook

99-215051 Use Loctite on Threads| 99-215042 ~ 99-215061 Washer Dust Skirt Rider

Extension Spring

99-215052 Harness Spring

Figure 4-2 Pot Joystick Assembly 171107-001 99-215043 Soc:Hd. Screw (4 places)

| Upper Housing

__| 99-215058 | Universal Joint

| 99-215045, Pivot Ball

99-215046 Lower Housing

99-215047 Stop Piate

99-215048 EB Paiymer tex nut (4 places)

99-215049 Monospring Housing

'99-215050 Spring Swivel Lug

Page 35

Space Lorps & Cuaprer 4— Parts Iccustrations

NOTE Asmall number of Space Lords games initially produced used an alternate pot joystick assembly — part no. A050136-01. That assembly is illustrated in the supplement 171100-003 to this manual, CO-380-02 Right Hand Grp Assy (includes all parts shown on this page, except the joystick handle and discs)

171098-001 “Trigger Switch Assembly ~ 15010 ; soatsn rion ce JS} ser rrr SOU Eley Assy.

99-215640 Sorew (4 places)

178249-104 Left Cover

99-215041 Pot Joystick Shaft

| Shatt is part of Pot Joystick Assy. (171107-001) 99-215062 Upper Washer (Part of the housing assembly, 908s 0n top of the contol panel)

178027-001 Nyogel Lubricant

Figure 4-2 Pot Joystick Assembly 171107-001

Page 36

CHAPTER 4 — PaRTS ILLUSTRATIONS SPACE LORDS

99-15104 Base Plate WIPivot & Studd 99-15025 Coin Inlet, Left | 98-15113, Key Hook 99-15086 Coin Mechanism

99-15026 Right Coin Inlet 99-15056 ‘Screw for Bezel ee

a i

if

“ S i aa Sot 99-15096 < 1 | Sw. Aduster i 99-15100 jie Lamp _ 99-15056. Le Sorew a Vy 99-15131 Elastic Locknut 99-15132 Snap-on Sieeve

99-1610 Snap-on Clip

99-1533) Hold Down Bracket

‘Screw for Bezel 99-15128 iut/Washer for’ Me Mounting pall Coin Ret. Plate | 99-15028 Coin Ret. Box

99-15056 ‘Screw for Bezel 99-15129 Mounting Stud (2 places)

99-15051 }99-15134 Lamp Holder 4-40-1" Pan-Head Screw

99-15126 99-15028 San MS Flat-Head Mounting Screw 99-15042| 99-15085 Switch Coin Door Hamess

Figure 4-3 Over/Under Coin Door and Cash Box 171093001 (171095-001 is an acceptable substitute)

4-6

Page 37

Space Lorps #% CHAprer 4 — Parts ILLUSTRATIONS

99-15038 Bezel for Button Cover

99-15001 thru 99-15012 Return Button

99-15039 Bezel for Cover

99-15125 Frame Hinge Screw

99-15052 ~ Spring for Button A

99-15110 99-15088, Enclosure

Clamp

199-15135 Frame Clamp Screw

99-15116 Upper Door

9915115 Lower Door

99-1514 Die Cast Frame

99-15111 Coin Counter

99-15127 Meter Mounting Screw

Figure 4-3 Over/Under Coin Door and Cash Box 171093-001 (171095-001 is an acceptable substitute)

~ N

Page 38

CHaprer 4— Parts ILLUSTRATIONS “ SPACE LorDs

174088-002 Turbo T-Handle ‘Thruster Joystick 177010-240 10-24 Pollock Hex-Locknut (8 places) 75-5168 10-24 x 1.00" Carriage Bott (8 places) 1750141040 #10, 219 x.500 Zine Washer (places)

051072-01 Control Panel 051152-01 Conlrol Panel Decal

178237-001 ied Horizontal Nylon Butlon Assy. (2 places) 1160044-001 SVISMA 187 Snap-Spot Switch (4 places)

178237-005 Blue Horizontal Nylon Button Assy. 1160044-001 SVISMA .187 Snap-Spot Switch 1178263-0402 1/4" W. x 118° T. Foam Tape (28) +71400-008 Right Handle Grip Assy (2 places) Sritoro03 Analog Joystick Without Grip (2 places} 1551408 026% 2 12" Cartage Bok (6 paces) 477010240 40:24 Pollock texcLocknut (8 places) {76014-1040 #10, 219 x.500 Zine Washer (6 places) 051199401 Joystick Mounting Clamp (4 places)

NOTE: To.usa the altomate joystick, replace these two items with: ‘A049009-02 Pot Joystick Assy. (2places)

Butt-Hd. Screw (2 places) 17014-3050 1/4" Flat Washer "(2 places)

‘8050673-01 Control Panel Haines Assy.

Figure 4-4 Control Panel Assembly A051103-01 B

Page 39

Space Lorps ¢ CHAPTER 4— Parts ILLUSTRATIONS

‘72-HAA606S +#6-32 x 3/8" X-Rec Screw (2 places) 179231-002 2 Position Flat-45-90 051003-01 Terminal Block Power Supply Chassis

Q

4 A ® ® a” © : afin oie iif

|®|

iyi

® ® ® im

t ® ® ® ® wi i a F Hey

050886-01 Power Supply Bracket 142059-001 149016-001 Isolation 200W, AT Power Supply Transtormer "72-HAG606S (2 places) #6-32 x 3/8" X-Rec Screw 72-HA4806S (5 places) #822918" X-Rec Screw (@ places)

Figure 4-5 Power Supply Assembly A050680-01 B

Page 40

4-10 Figure 4-6 Turbo T-Handle Thruster Joystick Assembly 171088-002 ‘99.215076 114-20 x 1/2" Screw (2 places) 99-215068 Top/Side Welded Plate Assy. 99-215067 Forward/Reverse Plate

99-215081

Gold DA3 Series Microswitch

(included with Pushbutton)

reed ih Pestinton) 99-215065

Delrin Pin

99-215080

Pushbutton with

Gold Microswitch

| 99-215063 1T-Handle Knob & Shaft 9.215048 1/4-20 Nylon Insert Nut

(4 places)

99-215070 Sleeve i.

(places) |

99215069 Bumper @ places) | 99-215074 ‘Switch Bracket 99-215079 Atari Shifter Harness (2 places) 99-215072 e 99-21 x Ring '5071 99-215073 Return Bracket 99-215075 114-20 x 1 1/2" Screw (2 places) 99-215078 2-56 x 1/2" Screw

| 99-215085 #2-56 Hex Nut

Cuaprer 4 — PARTS ILLUSTRATIONS # Spack LORDS

Page 41

Space Lorps CHaprer 4 — Parts ILLUSTRATIONS

176349-3644 #6-32 x 2 9/4" M-F ‘Alum. Standoff (2 places) 178181-6616 1/4" Round, 1" Lg. Alum. Standoff (2 places) 175015-0113 #6 Sti/Cad Ext.- Tooth Lock Washer (2 places) 172025-3622 6-32 x 1 3/8" Lg, X-Rec Pan-Hd. Screw (2 places)

178065-100 4" Wire & Cable Tie 178068-002 1" Sq. Cable Tie Mount

‘A050675-01 CLARN Il Interconnect Harness Assy.

‘A050679-01 Link PCB Hamess Assy.

051059-01 Double Board Set Hat

177018-206 # 6-32 Brass Thumbnut (10 places) A049810-03 Space Lords Game PCB Assy.) (EPROM Version) (2 places)

‘A047292-03 JAMMA Filter PCB Assy. (2 places) or

‘A050349-01 CLARN II Ribbon Assy.

‘A051092-01 CLARN II PCB Assy.

178278-616 #6-32 x 1,00" Nylon ‘Standoff 177000536 +#6-32 Nylon Hex Nut

178047-012 6" Nylon Card Guide (2 places)

‘A051096-01 Space Lords fotaeo1 8 Pitan Pe Asari

Assembiy (2 places)

A051099-01 B board set. 1 Le

Figure 4-7 Space Lords PC/Ground Plane Assembly 178349-3644 6-32 x 2.3/4" MF ‘Alum. Standoff (4 places) 175015-0113 #6 St/Cad. ExtTooth Lock Washer (4 places) 172025-3606 6-32 x 3/8" Lg, X-Reo Pan-Hd. Screw (4 places)

051060-01 Double Board Set Base “4

178171-1612 6-32 x .78", 1/4" Round Alum. Standoff (2 places) 172025-3606 6-32 x 3/8" X-Reo, Pan-Hd. Screw (4 places) 175014-2021 #6 Flat Washer (4 places) 175017-3013 +#6 Split Lock Washer (4 places)

034536-13 3x3 x 3/4" Thk. Foam Vibration Damper (hidden, place this item in center of double board set base)

‘A049954-01 JSA3S PCB Assy. (EPROM Version) (2 places) 178278612 #6-32 x .75° Nylon Standoft (places) 177000-538 +#6-32 Nylon Hex Nut (2 places)

4-11

Page 42

Cuarrer 4 — Parts ILLusTRATIONS % Space LORDS

ee : aw OO 0 cis BSB B, ¢ WARNING : Bos) BSE FOR CONTINUED PROTECTION R822 MRB22 AGAINST RISK OF FIRE,

BEADMT2 -12V+12Vpepvace ONLY WITH A FUSE
Ll oO.oOF THE SAME TYPE AND

az ELECTRICAL RATING.

ve2€e=
F2 ya/2sovCRIFB2F3 4A/250Vrea3

i ee

Fi 4As2sovFe.FY 4A/250VFey8

ee C3 C7 cH C8 Ho:

HN

e} [e)

Figure 4-8 Power Distribution PCB Assembly A050824-01 B

Power Distribution PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
C1-6,C9-C16.01 [LF, SOV, +80% -20% Cer. Cap.122002-10311,12‘N12N Ferrite Bead Inductor141003-005
c7-8100 pF, 100V, £5% Cer. Cap.122016-101RI, R2, R4,
Ji, J2Hr, Connector, 12 Ckt., .156 Ct, Key 9 179213-012ROResistor, 1.2 K Q, +5%, 1/8 W110027-122
JM1Har. Connector, 4 Ckt., !100 Ctr, Key 2.179118-004R3,R5Resistor, 470 Q, 45%, 1/8 W110027-471
JA,JBHar. Connector, 4 Ckt., .200 Ctr179310-004GND1Test Point179051-001
38,39Har. Connector, 6 Ckt., .156 Ctr179309-006Ql, Q2_—_BUZ11 Transistor133054-001
JM2Har, Connector, 9 Ckt., 156 Ctr, Key 3179213-009HS1, HS2 TO-220 Heat Sink with #4-40 Stud178063-007
JcHdr. Connector, 9 Ckt., 156 Ctr, Key 6179213-009FI-F43AG 4 Amp 250 V Slow-Blow Fuse146008-4022
CR1, CR2 MR822 Diode131019-001GAS1, HS2) #4-40 Steel/Zinc Hex Nut177000-132
CR3-CR8__MV5053 Light-Emitting Diode131027-002(HS1, HS2) #4 Steel/Zinc Internal-Tooth Washer75-054
FBI-FB43AG Fuse Block179225-4401(HSi, HS2) #4 Steel/Zinc Rect. Washer178347-001

4-12

Page 43

4-13 Figure 4-9 JSA3S PCB Assembly (EPROM Version) A049953-XX A. ” HCT273 da Fist Fr QB sa] Ri sou Ls374 §

el

° 2») a oe ae ® uses7 & 302] 1273. LS257 Ge 39°38 g957 g

ES | 0 ey 3} C56 CST , ioe a & z = g css - csq gs ia g 5g cre 02] Zz e

ceo 5,

oO 12014 dl & ¢>)ca R103 6 y, 18 19

ces Space Lorps CHaprer 4— Parts ILLUSTRATIONS

Page 44

Cnaprer 4 — Parts IiusrraTIONS & Spacr Lorps

JSA3S PCB Assembly (EPROM Version) Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
Socket, 16 Pin, .300179259-01619EIC, RAM, 8KX8, 100 ns, 6137535-004
Socket, 20 Pin, .300179259-02019)Ic, YM2151137401001
Socket, 24 Pin, .600179257-02419L.IC, YM3012137402-001

Socket, 28 Pin, .600 179257-028

Socket, 32 Pin, .600179257-032C1, C2Capacitor, 47 MF, 50 V, Electrolytic123015-476
Socket, 40 Pin, .600179257-040C3, C4Capacitor, .1 WF, 50 V, +80%-20%, Cer.122002-104
torsCapacitor, 47 F, 50 V, Electrolytic123015-476
1K, ILIC, 4066B137580-0016, C7Capacitor, .1 UF, 50 V, +80%-20%, Cer.122002-104

2A,2E,3A,3E IC, TDA2030 137301001

4K, 4LIC, Quad Op-Amp, [M3403137673-001C8,C9Capacitor, 10 UF, 25 V, Electrolytic124009-106
5AEPROM, 512KX8, 100 ns136095-0081C12~C23Capacitor, .1 UF, 50 V, +80%-20%, Cer.—122002-104
C24Capacitor, 47 UF, 50 V, Electrolytic123015-476
5DIC, 7805137596-001C25-C28Capacitor, .1 HF, 50 V, +80%-20%, Cer.122002-104
OFIC, Quad Op-Amp, LM3403137673-001
6KIC, 74HCT273137655-001C29Capacitor, .22 [F, 50 V, +10%, Cer.122015-224
OLIC, 4066B137580-001C30Capacitor, 10 wR, 25 V, Electrolytic124009-106
C31, C32Capacitor, .1 HE, 50 V, +80%-20%, Cer.122002-104
7AIC, 74HCT273137655-00133Capacitor, 10 pF, 25 V, Electrolytic124009-106
7CIC, 7418257137136-001
8EIC, MSM6295,137607-001C34-C46Capacitor, 1 pF, 50 V, +80%-20%, Cer.122002-104
8KIC, 74HCT273,137655-001C47Capacitor, .22 UF, 50 V, +10%, Cer.122015-224
48Capacitor, .1 UR, 50 V, +80%-20%, Cer.122002104
aLIC, 4066B137580-001C49.Capacitor, 47 UF, 50 V, Electrolytic123015-476
9IC, 7418257137136-001
10KIC, 74HCT273137655-001C50, C51Capacitor, .1 HF, 50 V, +80%-20%, Cer.122002-104
101.IC, 4066B137580-001C52, C53.Capacitor, 6800 pF, 50 V, #10%, Cer.—-122015-682
C54Capacitor, .1 pF, 50 V, +10%, Cer.122015-104
1AIC, 74L874137023-001C55Capacitor, 1000 pF, 100 V, +10%, Cer. — 122015-102
11CIC, 7418257137136-001
12KIC, 74HCT273137655-001C56Capacitor, 3900 pF, 50 V, +10%, Cer,122015-392
12LIC, 4066B137580-001C57Capacitor, .1 WF, 50 V, +80%-20%, Cer.122002-104
C58, C59Capacitor, 6800 pF, 50 V, +10%, Cer.122015-682
134IC, 74HCT273137655-001C60Capacitor, .1 UF, 50 V, +10%, Cer.122015-104
13CIC, 7418257137136-001
BFIC, Quad Op-Amp, LM3403137673-001C61, C62Capacitor, .1 UR, 50 V, +80%-20%, Cer.122002104
14EIC, MSM6295137607-001C63,Capacitor, 1000 pF, 100 V, +10%, Cer,122015-102
C64Capacitor, 3900 pF, 50 V, £10%, Cer.122015-392
14KIC, 741874137023-001C65-C70Capacitor, .1 UF, 50 V, +80%-20%, Cer.122002-104
14LIC, Quad Op-Amp, LM3403137673-001
15AIC, 7418240137251-001c72Capacitor, 1000 pF, 100 V, +10%, Cer.122015-102
15CIC, 7418257137136-001C73Capacitor, 2200 pF, 50 V, +10%, Cer.122015-222
C75,Capacitor, 1000 pF, 100 V, +10%, Cer.122015-102
16KIC, 7418393137146-001C76Capacitor, 2200 pF, 50 V, +10%, Cer.122015-222
WAIC, 74LS374137144-001
EFIC, 7418136137177-001C77-C81Capacitor, .1 HE, 50 V, +80%-20%, Cer.122002-104
17KIC, 7418393137146-001C83,Capacitor, 10 UF, 25 V, Elecirolytic124009-106
C85, C86Capacitor, 1000 pF, 100 V, 10%, Cer.122015-102
18AIC, 7418374137144-00187-C89Capacitor, .1 WF, 50 V, +80%-20%, Cer.122002-104
18BIC, 74F74137436-001
18EEPROM, 64KX8, 200 ns136095-0080CR1,CR2Diode, MV5053, Light-Emitting131027-002
18FGALI6V8, 25 ns136095-0082CR3,CRO-CR9 Diode, 1N4001131048-001
CRIODiode, 1N5818131025-001
19AIC, 6502 A13757-0901CRII-CR14 Diode, 1N4001131048-001
Page 45

Space Lorps CHaprer 4 — PARTS ILLUSTRATIONS

JSA3S PCB Assembly (EPROM Version), Continued Parts List

Desig- Desig-

nator _ DescriptionPart No.nator_ DescriptionPart No.
GND2Test Point179051-001ROSResistor, 15 KQ, 45%, 1/8 W110027-153
HS1, HS2_Heat Sink, TDA2030178190-024
JAUDConn, 36 Ckt, .1 Bottom Entry179299-036RO6Resistor, 30 KQ, +5%, 1/8 W110027-303
RO?Resistor, 3.9 KQ, 45%, 1/8 W110027-392
RIResistor, 1.2 KQ, #5%, 1/8 W110027-122RODResistor, 75 KQ, 45%, 1/8 W110027-752
R2Resistor, 470 Q, +5%, 1/8 W110027-471R70Resistor, 15 KQ, 45%, 1/8 W110027-153,
R3Resistor, 33 KQ, 45%, 1/8 W110027-333
Ra, RSResistor, 3.3 KO, +5%, 18 W110027-332R71Resistor, 30 KQ, +5%, 1/8 W110027-303
R72Resistor, 33 KQ, 45%, 1/8 W110027-333
R6Resistor, 33 KQ, +5%, 1/8 W110027-333R73Resistor, 5.1 KQ, +5%, 1/8W110027-512
RO, RIZ-RI5 Resistor, 1 KQ, +5%, 1/8 W110027-102R74, R77_—_-Resistor, 12 KQ, +5%, 1/8 W110027-123
RIG-RI9Resistor, 470 Q, 25%, 1/8 W110027-471
R20Resistor, 1 KQ, #5%, 1/8 W110027-102R78Resistor, 33 KQ, £5%, 1/8 W110027-333
R79Resistor, 3.3 KQ, +5%, 1/8 W110027-332
R22Resistor, 10 KQ, +5%, 1/8 W110027-103R80Resistor, 5.1 KQ, 45%, 1/8W110027-512
R23Resistor, 1 KQ, +5%, 1/8 W110027-102R81Resistor, 12 KQ, 45%, 1/8 W110027-123
R24Resistor, 33 KQ, 45%, 1/8 W119027-333
R25Resistor, 1 Q, 45%, 1/8 W110027-010R83Resistor, 3.9 KQ, +5%, 1/8 W110027-392
R84Resistor, 12 KQ, £5%, 1/8 W110027-123
R26Resistor, 33 KQ, £5%, 1/8 W110027-333R86Resistor, 3.3 KQ, +5%, 1/8 W110027-332
R27Resistor, 1 KQ, +5%, 1/8 W110027-102R87Resistor, 82 KQ, 45%, 1/8 W110027-823
R28Resistor, 33 KQ, #5%, 1/8 W110027-333
R29Resistor, 1 Q, £5%, 1/8 W110027-010R88Resistor, 5.1 KQ, £5%, 1/8W110027-512
R89Resistor, 620 KQ, +5%, 1/8 W110027-624
R30Resistor, 1 KQ, £5%, 1/8 W110027-102ROOResistor, 10 KQ, +5%, 1/8 W110027-103
R31, R32_—_Resistor, 33 KO, +5%, 1/8 W110027-333ROLResistor, 39 KO, +5%, 1/8 W110027-393
R33Resistor, 1 ©, #5%, 1/8 W110027-010
R34Resistor, 33 KQ, 45%, 1/8 W110027-333R92Resistor, 160 KQ, +5%, 1/8 W110027-164
R93Resistor, 330 KQ, +5%, 1/8 W110027-334
R35Resistor, 1 KQ, +5%, 1/8 W110027-102R94Resistor, 20 KQ, 45%, 1/8 W110027-203
R36, R37_Resistor, 33 KQ, £5%, 1/8 W110027-333R95Resistor, 82 KQ, +5%, 1/8 W110027-823
R38Resistor, 1 Q, +5%, 1/8 W110027-010
R39, R40, Ré4 Resistor, 10 Q, 45%, 1/8 W110027-100R96Resistor, 5.1 KQ, +5%, 1/8W110027-512
R97Resistor, 620 KQ, +5%, 1/8 W110027-624
RASResistor, 27 KQ, 45%, 1/8 W110027273ROBResistor, 10 KQ, #5%, 1/8 W110027-103
RAGResistor, 15 KQ, 45%, 1/8 W110027-153R99Resistor, 39 KQ, +5%, 1/8 W110027-393
RYResistor, 19 KQ, +5%, 1/8 W110027-103
R48Resistor, 2 KQ, +5%, 1/8 W119027-202R100Resistor, 160 KQ, +5%, 1/8 W110027-164
ROIResistor, 330 KQ, £5%, 1/8 W110027-334
R49Resistor, 75 KQ, +5%, 1/8 W110027-752R102Resistor, 20 KQ, +5%, 1/8 W110027-203
R50, R51_—_-Resistor, 6.8 KQ, +5%, 1/8 W110027-682R103Resistor, 470 Q, 15%, 1/8 W110027-471
R52Resistor, 10 Q, 45%, 1/8 W110027-100
R54Resistor, 27 KQ, #5%, 1/8 W110027-273R105Resistor, 560 Q, #5%, 1/8 W110027-561
R106Resistor, 10 KQ, +5%, 1/8 W110027-103
RSSResistor, 15 KQ, £5%, 1/8 W110027-153
R56Resistor, 10 KQ, +5%, 1/8 W110027-103(HS1,HS2)Thermal Compound107031-001
R57Resistor, 2 KQ, +5%, 1/8 W110027-202
R58.Resistor, 75 KQ, +5%, 1/8 W110027-752
R59, R6OResistor, 6.8 KQ, +5%, 1/8 W110027-682
R61Resistor, 10 Q, +5%, 1/8 W110027-100
RO4Resistor, 75 KQ, +5%, 1/8 W110027-752
Page 46

Cuapter 4 — Pars Intustrations ¢ Spacr Lorps

4-16

Page 47

A051092-XX D Figure 4-10 CLARN II PCB Assembly

4-17 O gMVS053 pap 2 &

#1 109 1s, si) Os* cas 2 vs2us g 2» J02_ oO Ph 5 0. ooo x N

By Sejse40 wsoss

74ALS195 Space Lords % Cnaprer 4 - Parts ILLUSTRATIONS

Page 48

Cuaprer 4 — Parts ILLUSTRATIONS ¢ Space LoRDS

CLARN II PCB Assembiy Parts List

Desig- Desig-

nator —_ DescriptionPart No.nator —_- DescriptionPart No.
ySocket, 28 Pin, .600179257-028C42Capacitor, 33 pF, 100 V, +5%, Cer. — 122016-330
2DSocket, 68 Pin, PLCC179237-068C43-C57_—Capacitor, 100 pF, 100 V, +5%, Cer.122016-101
2FSocket, 28 Pin, .300179259-028C70-C83Capacitor, .1 UF, 50 V, +80%-20%, Cer. 122002-104
SESocket, 48 Pin, .600179257-048C84Capacitor, 10 HF, 25 V, Electrolytic124009-106
SJSocket, 24 Pin, .600179257-024

C85 Capacitor, .1 MF, 50 V, +80%-20%, Cer. 122002-104

7Socket, 20 Pin, .300179259-020C86Capacitor, 10 UF, 25 V, Electrolytic124009-106
8DSocket, 68 Pin, PLCC179237-068c87Capacitor, .1 UF, 50 V, +80%-20%, Cer. 122002-104
8FSocket, 28 Pin, .300179259-028C88, C89Capacitor, 33 pF, 100 V, +5%, Cer. — 122016-330
++1005VL Test Point179051-00190, C91Capacitor, .1 UF, 50 V, +80%-20%, Cer. 122002-104
++1005VR Test Point179051-001C92-C95Capacitor, 47 pF, 100 V, +5%, Cer.122016-470
GND1-4Test Point179051-001C96-C99Capacitor, 100 pF, 100 V, 45%, Cer.122016-101

C100, C101 Capacitor, 1000 pF, 100 V, £10%, Cer. 122015-102

1cIC, 74F32137486-001
2FIC, RAM, 8Kx8, 45 ns, .3137667-045CRI-CR3_Diode, LED, MV5053131027-002
4cIC, 74F00137327-001
4D, 4FIC, 7418245137134-001nConnector, 60 Circuit, Rec, 1x .1C179303-060

j2 Connector, 60 Circuit, Header,

5CIC, 74F00137327-0014 Wall, 1x .1C179021-060
SEIC, SRAM DP, 2Kx8, 55 ns, .6137681-055J3-J5Connector, 2 Circuit, Hdr., .100 Ctr—179048-002
SJIC, Controller, Univ Lan, 2Kx8RAM — 137710-001J7Connector, 11 Circuit, Header,
6AIC, 74F32137486-001-100 Ctr, Key 5179118-011

yo Connector, 11 Circuit, Header,

6D, 6FIC, 7418245137134-001-100 Ctr, Key 2179118-011
7GALI16V8, 25 ns136095-0070
8D1020 FPGA136095-0072L1Inductor, Ferrite Bead, N12N141003-005
8FIC, RAM, 8Kx8, 45 ns, 3137667-045
R1, R2Resistor, 220 Q, +5%, 1/8 W110027-221
8F/J, 8)IC, LTC485137711-001R3Resistor, 10 Q, £5%, 1/8 W110027-100
10KIC, 74HC14137605-001R14Resistor, 470 Q, +5%, 1/8 W110027-471
11FIC, 7418259137137-001R15Resistor, 1 KQ, +5%, 1/8 W110027-102
clCapacitor, 100 UE, 16 V, Electrolytic,R16Resistor, 470 Q, +5%, 1/8 W110027-471
Radial123013-107R17Resistor, 1 KQ, +5%, 1/8 W110027-102
C2Capacitor, 47 pF, 100 V, +5%, Cer.122016-470R30Resistor, 330 Q, +5%, 1/8 W110027-331
C3Capacitor, 33 pF, 100 V, +5%, Cer.122016-330R31-R34_Resistor, 1 KQ, +5%, 1/8 W110027-102
C4, C5Capacitor, 100 pF, 100 V, +5%, Cer.122016-101
R35-R38Resistor, 100 Q, 5%, 1/8 W110027-101
C6.-C8Capacitor, 33 pF, 100 V, +5%, Cer. — 122016-330R39Resistor, 150 Q, +5%, 1/8 W110027-151
C9.-, C17Capacitor, 100 pF, 100 V, +5%, Cer.122016-101
clsCapacitor, .1 UF, 50 V, +80%-20%,X1Crystal, 14.318 MHz, Osc. Module,
Ceramic122002-1043x .3 DIP144009-001
c19Capacitor, 33 pF, 100 V, +5%, Cer.122016-330x2Crystal, 20.000 MHz144000-003

20 Capacitor, .1 UF, 50 V, +80%-20%, Ceramic 122002-104

€21-C26Capacitor, 100 pF, 100 V, +5%, Cer.122016-101

GH Capacitor, 100 UF, 16 V, Electrolytic, Radial 123013-107 €36-C41 Capacitor, .1 UF, 50 V, +80%-20%, Cer. 122002-104

Page 49

Space Lorps “% CHAPTER 4 ~ Parts ILLUSTRATIONS

NOTES

4-19

Page 50

Space LORDS CHAPTER 4 — PARTS ILLUSTRATIONS %

== tC =

  • S|

EST er OD

fe Cae a GE CC a = =O = 26 C= 9 C22 fe Ce ee

<a) = 2% a |] 0 eer =o oe = jo = (pn - a ~ Ei 6 Wjp = jp = jp = if nD = o = D = Ll | G@ = jo = DQ = F a 9 = ap p Bee 5 af 5 la oh = fe ai Cs 0 E"

eo = 20f

C0 20Te 0 = 00 = ie ra ey

Share BETS

Figure 4-11 Space Lords Game PCB Assembly (EPROM Version) A049810-04 A

4-20

Page 51

Space Lorps # CHAPTER 4 — Parts ILLUSTRATIONS

Space Lords Game PCB Assembly Parts List

Desig- Desig-

nator_DescriptionPart No.nator _ DescriptionPart No.
2D, 2)Socket, 32 Pin, .600179257-0322DEPROM, £12K x 8, 100 ns136094-0030
3LSocket, 40 Pin, .600179257-0403LIC, SOS137550-001
3NSocket, 24 Pin, .300179259-024
SD, 5JSocket, 32 Pin, .600179257-0323NGAL20V8, 25 ns136094-0019
3RIC, 7418163 A137114-001
5N,5RSocket, 20 Pin, 300179259-02038IC, 741874137023-001
5U, 5V, 5W Socket, Zip 28179302-0284BIC, 7418260137332-001
OLSocket, 40 Pin, .600179257-040
JN, 7RSocket, 20 Pin, .300179259-0205ARes, R/2R, 1K/2K.118016-001
5DEPROM, $12K x 8, 100 ns136094-0031
8D, 8)Socket, 32 Pin, .600179257-0325NGALI16V8, 25 ns136094-0010
10U, 10V, 10W5RGALI6V8, 25 ns136094-0011

Socket, Zip 28 179302-028

121,Socket, 20 Pin, 300179259-02058IC, 74F08137483-001
3cSocket, 24 Pin, .600179257-024srIC, 74F32137486-001

5U, 5V, SW IC, VRAM, 256K x 4, 100 ns 137682-100

13E, 13F — Socket, 24 Pin, .300179259-0246LIC, PFHS.137419-104
13NSocket, 32 Pin, .600179257-032
14RSocket, 20 Pin, .300179259-0207ARes, R/2R, 1K/2K118016-001
168Socket, 68 Pin, Plee179237-0687BIC, 7418260137332-001
JNGALI6V8, 25 ns136094-0009
7kSocket, 20 Pin, .300179259-0207RGALI6V8, 25 ns136094-0012
20)Socket, 24 Pin, 300179259-024
208Socket, 20 Pin, 300179259-02078IC, 741886137079-001
21A, 21E, 21J, 21M, 21N8DEPROM, 512K x 8, 100 ns136094-0032
Socket, 28 Pin, .600179257-0288LIC, 74F02137481-001
8MIC, 7418157137029-001

21S, 22R, 228

Socket, 20 Pin, 300179259-0208NIC, 74F85137685-001
23E, 23]Socket, 32 Pin, 600179257-0328R, 8SIC, 74F157137494-001
23R, 238, 25D, 25K, 27D9cIC, 748153137104-001
Socket, 20 Pin, .300179259-0209F 9KIC, 7418298137201-001
2Socket, 68 Pin, PLCC179237-068
OLIC, 7418163 A137114-001
30NSocket, 20 Pin, 300179259-0209MIC, 74F04137437-001
31L, 31N, 31R, 31T, 33L, 33N, 33R, 33TONIC, 7418244137038-001
Socket, 32 Pin, .600179257-032OR, 98IC, 74F157137494-001
34E, 35)Socket, 28 Pin, 600179257-028
35L, 35N, 35R, 351, 37E, 37), 37L, 37N, 37R, 37T10D, 10FIC, 74HCT273137655-001
Socket, 32 Pin, .600179257-03210KIC, 74F04137437-001
10LIC, 7418273137040-001
+IC, 74F163137345-00110MIC, 7418378137305-001
+EPROM, 128K x 8, 100 ns136094-002110NIC, 7418244137038-001
+EPROM, 512K x 8, 100 ns136094-005310R, 108IC, 74F157137494-001

10U, 10V, 10W IC, VRAM,

INIC, 7418163 A137114-001256K x 4, 100 ns137682-100
1RIC, 74F00137327-00111KIC, 74F153137492-001
1sIC, 74F04137437-001
1IC, 74F32137486-001LILIC, 7418273137040-001
11MIC, 7418377137145-001
2aRes, R/2R, 1K/2K118016-00111NIC, 741378137305-001
2BIC, 7406137052-00111R, 11SIC, 74F157137494-001

4-21

Page 52

CHapTer 4 ~ Parts ILLUSTRATIONS

Space Lords Game PCB Assembly, Continued Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
12KIC, 74F153137492-00119M, 19NIC, 7418245,137134-001
12LGALI6V8, 25 ns136094-000719R, 198IC, 74F374137420-001
12M.XC, 7418157137029-001
12RIC, 74F377137622-00119WIC, 74F378137012-001
20FIC, 74F138137521-001
128IC, 74F174137531-00120)GALG001, 35 ns136094-0005,
RvIC, 7418377137145-00120LIC, 74F153137492-001
13CIC, 28C16-200, 200 ns137648-200
13E, 13FIC, RAM, 2K x 8, 35 ns, 3137534-00120RIC, 74F374137420-001
20SPROM, 825147136094-0003
13NEPROM, 128K x 8, 100 ns136094-0025,20WIC, 74F163137345-001
14KIC, 74F153137492-00121AIC, ADCO809137243-061
14LIC, 7418163 A137114-001
14MIC, 7418378137305-00121B, 21)IC, RAM, 32K x 8, 70 ns, .6137615-070
21LIC, 74P153137492-001
14RGALI6V8, 10 ns.136094-0006,21M, 21N _ IC, RAM, 32K x 8, 70 ns, .6137615-070
148IC, 747163137345-00121PIC, 74F04137437-001
14VIC, 74F377137622-001
ASKIC, 74P153,137492-00121RIC, 74F374137420-001
218PROM, 825147136094-0002
15LIC, 74F20137530-00121WIC, 74F163137345-001
15M.IC, 748377137145-00122A, 22BIC, 7418257137136-001
ISNIC, 74F260137570-001
ISRIC, 74F169137496-00122LIC, 74F153137492-001
22RGAL16V3, 25 ns136094-0014
1swIC, 74F32137486-001228PROM, 828147136094-0001
16D, 16FIC, 74F374137420-001,22IC, 74F163137345-001
16KIC, 74F1S7137494-001
16LIC, 74LS163 A137114-00123BIC, 74L8244137038-001
23EEPROM, 128K x 8, 100 ns136094-0221
16M, 16NIC, 7418374137144-00123)EPROM, 128K x 8, 100 ns136094-0222
16RIC, 74F169137496-00123LIC, 74F 153137492-001
168FPLA, 20 ns136094-0004
16WIC, 74F163137345-00123RGALI6V8, 25 ns136094-0016
238GALI6V8, 25 ns136094-0015
17D, 17FIC, 7418244137038-00123WIC, 74F157137494-001
17KIC, 74L$197137240-00124BIC, 7418273137040-001
VLGAL16V8, 25 ns136094-0008
17M, 17N _ IC, 7418374137144-001241IC, 74F153137492-001
24M, 24NIC, 7AF163137345-001
DRIC, 74F169137496-00124RIC, 74F151137490-001
17WIC, 74F163137345-00125DGALI6V8, 25 ns136094-0013

18D, 18F — IC, 74LS245 137134-001

18KIC, 74FO8137483-00125FIC, 74F32137486-001
25KGAL6V8, 25 ns136094-0018
18LIC, 74F153,137492-00126BIC, 7418245137134-001
18M, 18NIC, 7415245137134-00126LIC, 74F153137492-001
18RIC, 74P378137612-001
18WIC, 74F260137570-00126M, 26NIC, 74F163137345-001
26RIC, 74F157137494-001
19D, 19FIC, 74F138137521-00127DGAL16V8, 25 ns136094-0017
19KIC, 74LS74137023-00127FIC, 74F244137502-001

4-22

Page 53

Space Lorps CHaprer 4 — Parvs ILLUSTRATIONS

Space Lords Game PCB Assembly, Continued Parts List

Desig- Desig-

nator_DescriptionPart No.nator _ DescriptionPart No.
27IC, CPU, PLCC137658-101C4, (, C7, C8 Capacitor, .01 UF, 50 V, +80% -20%,
awIC, 74F377137622-001Ceramic122002-103
28BIC. 7418245137134-001€9,C10Capacitor, 1000 pF, 100 V, +10%, Ceramic
28LIc, 74F00137327-001122015-102
28M, 28N IC, 74F163137345-001C11, C12Capacitor, 270 PFC, 50 V, EMI Filter140006-271
28RIC, 74586137649-001C13Capacitor, 100 pF, 100 V, +5%, Ceramic 122016-101
29DIC, 7404137437-001ciaCapacitor, 270 PFC, 50 V, EMI Filter140006-271
30BIC, 7418244137038-001C15, C16Capacitor, .1 UF, 50 V, +80% —20%,

Ceramic 122002-104

30LIC, 74°74137436-001
30NIC, 74F138137521-001C17-C19_—Capacitor, .01 UF, 50 V, +80% 20%,
30RIC, 74F273137610-001Ceramic122002-103
31BIC, 7418257137136-001€20, C21Capacitor, .1 UF, 50 V, +80% -20%,

Ceramic 122002-104

31DIC, 7418148137417-001€22-€29Capacitor, .01 UF, 50 V, +80% -20%,
ayIC, CPU, 68EC020, 16 MHz, 100PQFP 137691-001Ceramic122002-103
31LEPROM, 512K x 8, 100 ns136094-0040€30-C35, C36-C58
31NEPROM, 512K x 8, 100 ns136094-0041Capacitor, .1 UF, 50 V, +80% -20%,

Ceramic 122002-104

31REPROM, 512K x 8, 100 ns136094-0048
31TEPROM, 512K x 8, 100 ns136094-0049csoCapacitor, 100 UF, 16 V, Electrolytic,
32BIC, 7418244137038-001Radial123013-107
32D, 32W IC, 74F244137502-001C60-C72Capacitor, .1 UF, 50 V, +80% —20%,

Ceramic 122002-104

33BIC, 7ALS257137136-001C73Capacitor, 109 pF, 100 V, 15%,
33DIC, 74244137502-001Ceramic122016-101
33LEPROM, 512K x 8, 100 ns136094-0042C74-C248 Capacitor, .1 UF, 50 V, +80% -20%,
33NEPROM, 512K x 8, 100 ns136094-0043Ceramic122002-104
33REPROM, 512K x 8, 100 ns136094-0050CRIDiode, MV5053, Light Emitting131027-002
33TEPROM, 512K x 8, 100 ns13604-0051CR2, CR3.Diode, 1N4001131048-001
34BTC, 7ALS257137136-001
348, 35)IC, RAM, 32K x8, 70 ns, 6137615-070GND1,GND2 Test Point179051-001
35LEPROM, 512K x 8, 100 ns136094-0044JAConnector, 2 Circuit, Header, .100 Ctr 179048-002
35NEPROM, 512K x 8, 100 ns136094-0045,JAUDConn, 36 Ckt, 1 Hdr, Long179300-036
35REPROM, 512K x 8, 100 ns136094-0052JPL3Conn, 15 Ckt, Hdr, 100 Ctr179118-015,
35TEPROM, 512K x 8, 100 ns136094-0053JROMConn, 60 Ckt, Hdr, 1x .1C179291-060
36BIC, 7ALS257137136-001JSYNCConn, 3 Ckt, Hdr, 100 Ctr179048-003
36WIC, 74F244137502-001IxConn, 60 Ckt, Hdr, 1.x 1C179291-060
37EEPROM, 128K x 8, 100 ns136094-0223
37)EPROM, 128K x 8, 100 ns136094-0224QI-Q3Transistor, 2N3904133041-001
Q#+Q6Transistor, 2N5306133033-001
37kEPROM, 512K x 8, 100 ns136094-0046
37NEPROM, 512K x 8, 100 ns136094-0047RtResistor, 1 KQ, +5%, 1/8 W110027-102
ADC.VREConnector, 2 Circuit, Header, .100 Ctr 179048-002RI,R2Resistor, 470 Q, 45%, 1/8 W110027-471
RBResistor, 10 Q, +5%, 1/8 W110027-100
C1, C2Capacitor, 100 pF, 100 V, +59, Ceramic 122016-101R4Resistor, 100 Q, £5%, 1/8 W110027-161
C3Capacitor, .1 UF, 50 V, +80% -20%,RSResistor, 15 Q, +5%, 1/8 W110027-150

Ceramic 122002-104

4-23

Page 54

CHapTER 4~ Parts ILLUSTRATIONS “ Spack LORDS

Space Lords Game PCB Assembly, Continued Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
RGResistor, 1 KQ, +5%, 1/8 W110027-102R88Resistor, 470 Q, +5%, 1/8 W110027-471
R7Resistor, 24 KQ, 45%, 1/8 W110027-242RS9-R100 Resistor, 1 KQ, 45%, 1/8 W110027-102
R8Resistor, 470 Q, +5%, 1/8 W110027-471R1O1-R106 Resistor, 470 Q, +5%, 1/8 W110027-471
ROResistor, 10 Q, 5%, 1/8 W110027-100R108Resistor, 10 Q, 45%, 1/8 W110027-100
R10Resistor, 100 Q, £5%, 1/8 W110027-101R109Resistor, 1 KQ, +5%, 1/8 W110027-102
RuResistor, 15 2, +5%, /8 W110027-150R110Resistor, 10 Q, 45%, 1/8 W110027-100
R12Resistor, 1 KQ, +5%, 1/8 W110027-102R12Resistor, 10 KQ, 5%, 1/8 W116027-103
RBResistor, 2.4 KQ, +5%, 1/8 W110027-242R113, R114 Resistor, 1 KQ, £5%, 1/8 W110027-102
RuResistor, 10 Q, 45%, 1/8 W110027-100RLSResistor, 10 KQ, £5%, 1/8 W110027-103
RISResistor, 100 Q, #5%, 1/8 W110027-101RINGResistor, 1 KQ, +5%, 1/8 W110027-102
RIGResistor, 15 Q, $5%, 1/8 W110027-150RLI7Resistor, 470 Q, +5%, 1/8 W110027-471
RI7Resistor, 1 KQ, 5%, 1/8 W110027-102Riu8Resistor, 1 KQ, +5%, 1/8 W110027-102
RI8Resistor, 2.4 KQ, $5%, 1/8 W110027-242R119Resistor, 10 KQ, +5%, 1/8 W110027-103
R19Resistor, 100 KQ, £5%, 1/8 W110027-104R120, R123, R124
R20Resistor, 240 Q, 45%, 1/8 W110027-241Resistor, 10 2, £5%, 1/8 W110027-106
R21Resistor, 0 Q, +5%, 1/4 W110005-001R125Resistor, 10 KQ, +5%, 1/8 W110027-103

R126, R127 Resistor, 1 KQ, +5%, 1/8 W 110027-102

R22-R27__Resistor, 1 KQ, +5%, 1/8 W110027-102
R28-R35Resistor, 470 Q, 15%, 1/8 W110027-471R128, R130-R133
R36-R41_—_Resistor, 1 KQ, 45%, 1/8 W110027-102Resistor, 10 Q,£5%, 1/8 W110027-100
R42, R43_—_Resistor, 10 KO, 45%, 1/8 W110027-103R135-R139 Resistor, 1 KQ, +5%, 1/8 W110027-102
R140Resistor, 470 Q, 45%, 1/8 W110027-471
R44Resistor, 100 Q, 45%, 1/8 W110027-101RIAI-RI45 Resistor, 1 KQ, 45%, 1/8 W110027-102
R45Resistor, 220 Q, 45%, 1/8 W110027-221
R46, RA7__Resistor, 100 Q, +5%, 1/8 W110027-101R146Resistor, 2.2 KQ, 45%, 1/8 W110027-222

R48, R49,

R52-R59Resistor, 1 KQ, +5%, 1/8 W110027-102STESTSwitch, Slide, SPDT160040-001
R6O-RG3_—_Resistor, 470 Q, 45%, 1/8 W110027-471VCRConnector, 2 Circuit, Header, 100 Ctr 179048-002
ROG-R71Resistor, 10 KQ, +5%, /8 W110027-103WDOG — Connector, 2 Citcuit, Header, 100 Ctr 179048-002
R72Resistor, 1 KQ, +5%, 1/8 W110027-102
R73Resistor, 10 KQ, +5%, 1/8 W110027-103x2Crystal, 14.318M, Ose. Module,

3x 3DP 144009-001

R74-R77Resistor, 470 Q, 45%, 1/8 W110027-471

R7S-R81_—_Resistor, 1 KQ, +5%, 1/8 W 110027-102

R82-RB6Resistor, 470 Q, 5%, V8 W110027-471
R87Resistor, 10 KQ, 45%, 1/8 W110027-103

4.24

Page 55

CHAPTER 5

Schematic Diagrams

INTRODUCTION

HIS CHAPTER contains the schematic diagrams for

all the Space Lords” printed-circuit boards, including

the game PCB (also called GX2), the JSA 3S PCB, the

CLARN II PCB, and the JAMMA Filter PCB, In addition, this

chapter includes

wiring diagrams for

the entire game Cin-

cluding the power

supply), and the

coin door. The PCB

assembly drawings

are illustrated in

Chapter 4, Parts

Illustrations.

Page 56

Carrer 5 — SCHEMATIC DiAGRAMS “ Space LoRDS.

soe sane — gt Terra

(OND? Jered Oa onooxo) JRe@-8 O—— nwovov
cho) Rae osoie. RiessLa
50> Jarema os os(90) Jaewmce O——s #3)sete Ns3 agi
©0950) Jaremcs Os syC503 arene O———+ +5oor owe ets aos
30) Semmes O30503 dance Os “8AB RE Oe
20) Jthe Oo220Ge42v) samna-F o——* +12vonoaSone
KEY Je? O-RY Jaan Om2

ceenrR) Imeem Q———* TENA. CCNTRRY Janae) Oa CONT CeeLOCKLD Jeers Oo CALOERRD dettmnek O-

Ceonaas ) ave 30 ©spreCSpKRiE) Stewie, ©SPR
CRUD: Janne il O————s ARRCUD END) leven ©SPARonQa,owes-Ott
CneD) aeesiei2 0 aDcoREENDTHE seueBYE vous
cued dormsets @———— Leestne>2Hi
cytp OND) JiweR-iW Oe vidoSERVICEDWE woe—O HP oe
csenprest) lates GOSeLFresterie)Om© m0,
CEOINL) JARMA-ie O——+ COINceomnt)HB vousFear
CSTRRTL) Jawa? Oa TRIEstrateoHss
CURUAD lftmn-is os rtcuPRe9 Fis ueBie eu

CORNEA JreR-39 O——* Dt oowwaa)

ELEPURD immed @—— ercanmmPOtoe

CRIGATLRD Jirew-at O———» Rt cxicntaa

cLEUMONDD mew-2eO———sretat——ceaurront)+0 #4 sexe

Clauttowe3 lence) o———srctet ——tmautTon)

CLBUTTON|D Jatwenes O————erecter—CaBUTTONS}TE woe

Clertea) Jamre-2s O——e ncITCL_CLEFTRBD nemo 9a RET? <RIGHTUBD lins-2¢ O————a ACTTRL ———_CRIGHTRED Jeep © ———+ ney Re COND> later e? O———= n> COND) Iap-ee Cs nd END) deemec2s Oo one {6D Ieeme-F @———« on m oor 2 aa oon oie oom e oe ins oa ofthat comers Pape ae cry wu oS imo otra 15 o—anctna i ts enema apo

  • o—enere oe 2 o—arere oy i o—actA Ss it o—er 4 rer OO wai 3 son ar i perenne
sag$e steersowt
ots sorts3 —scoiNaoR
of umrer4 Os Senvicessv
o2-. Dre20OF a
5° Seeraidcnn fe
oAi o—eoN35

otis cece ofsio1 ean Py ob wots ose

odesasyncrene
Sa buJo——ausrnc.ovtog ses
tes x08(2 O—* VSYNC.OUTOSS moe
ot x083 O——* VTOGND32 3x07

ot Trur on O35 os oF x08 te oS soe SF come oe n020 ot otto peut cs SE come weg XN oat surest ogg 3 1083 zn ots wis os tur a oth SERVICER we O82 Sener 3 OE OSL coarse ore

ofS Seanceoe ®wa deredersbess
OFS Seemec geWs sgmreerFakFRFimFe
oA2amare
oS| greLoveeeeom
ped33bag

ed osetin 35 EH oxo 6 oF s-5y ofS one sy os oS saw os

oo3—

ow ot Rie 2k oo

5-2

Page 57

Space Lorps * CHAPTER 5 — SCHEMATIC DIAGRAMS

sy rao x con enemen 85395395

i i

288, it

5 SSE Etech iedog2 Ty [ee : FH :

me

: aS ae

ery

weer SPARE

Pree

PRY 2

Foe

12 288

Fie 4 2st pritw—p—tag

Fox om see 20?

rot

:

ts x sf yt 5) 7 Te

ve

wey

ee

a8

Tie

mee oH Fa

Figure 5-1 Space Lords Game PCB (GX2) Assembly Schematic Diagram

049809-XX E,

Page 58

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 59

Space Lorps % CHAPTER 5 — SCHEMATIC DIAGRAMS

sevices v3 coma on crn Ura crea a5

rermz Actes crite acTBS pertLt Actas ecrTRs STARTS rotors)

rez nsos bain grios ane mim daer d mice 1% Mo Fue Bin Bin’ 200 gin eit etre miedo E #4 4 as na a miogtt Fl aE, | : a fete [ap cor 7 oo ase 7 ee He ls we rs 7 =] 1 a 52 [1 we 1 i a 38

  • [A yg 2 [+o T tli. * oy ce ten te Lege deo te bee Ley i Tt) te 7 Te 7! Te TT! Te

0 we we fas bars foe Jar Lass dan Jesse i to Zuo Fire Far Ein Fae uo Bre orm ——1ad5 a a a a ials———S fe ws ol, T PLS RSL ak 14 42 x03 ra 755 He" a, EE i + v2 r : mon r a ap | 7 BE 52 ro a 3 He

  • 7, Re 212 yy| + soo +— ra T T Tes? oot Lew toe Le Lew top Lege a ret a Th Tk fis fe Trt so Laser

a a

re one 194 raocur 4 oe ou

  • Tae] roconos on Fv geene—22/ p02 coe | 0. £00 pri rem a eae be ure et S| tur or FB —~eross i mo i a — Sine oe F3E—sheas re ne ost tren Ta 7 i one he oe rir roe i i PSeemes marae 8 Pas Sr ra he @ ES —ereta ami i ei oa im = fe ot Te to 62 tree aia vhasy poe uv cre ad > insoos Res cou et cena sans % ret — ms cee ott Roane . Groce Ep Te Cente conte wr azse ze baad Rae sao = cr - Seen centa oxo

owed

Figure 5-1 Space Lords Game PCB (GX2) Assembly Schematic Diagram 049809-XX E

Page 60

Cuarter 5 — SCHEMATIC DIAGRAMS “ SPace Lorps

13¢ muta oo i geen a Teme yy BAO sav 28) ose pole) aoe Hf me au

13K| ie380

crato HH ano Se

pr vor facCRRAfim 5ATRB ioe
autor =Steepta5 oy Letmre att anos
‘ies s————28 itaoeacon
vr vibe = licBless REre aa
toe <———$ aceOMHEAssaf 8s voie
viesSli ardTs; os [3Sri sats sro
o.87coSe 02we] sof Banoo
arasaam oo eef{20 taf Sesion
ee32 so 001010}Hoe

mem old ne rie 18 9g «28d ter

| 90Tree 0224 OFsocrer

r.vios sifecs

vioaeceA~

anvi0s Slee 23.6 ace Prviay Sic3 Pure ice

3altFan see
muer0yHicttcrow. o6 23
5cap1D wy
zers3won ter ptt

Be poe 43 34

Tyisworeda: 12a+

oe vos far, va -2 + oh se 24% cRR.oe orvi03 Bley

Fy1D3 =22hxce5ot
nvt03atfect ayforecoe
oa.atSacosv 2e

sve 284 ce

Prvitasca2
oa0.Fie
vioicera3] fe
e.vtoeSfic ayiho Sese
eesBese?alm Bacre ide
are3684idea 1 Aadaz
pemed{er ort30 sal «sor

Hime 06 LS ej Tape oe

oveBas os ee{60 sa $= 10s

Siew ov ft a] sab sero

asso saBsa
1Hae a EP30 sob aro
vr.yrosBisslao aeishor
fuiace5Shoo 0s0__sa2 9 1p9
woeliceoipg od osws
Pr. yiD0 =H1c3rman te a 2 OE—
vtootice|,
en utooSict ay}ur

ra vor oe at moeettas 13% weet 2

Boleaeepee

use eel cran.oc el Bie aos r r ur 50 sate

oteHYcalere
wsesiesHEpo 30S

rosie ve aaa

za8315 ithe

Sere | never

Te

abe de

Sood4—swc-our

See ree)

SFSo| a rrrrsra

we vein a4 ——— aoe —, vsrne. cur rs to cag bee = Tover Ail Storr oe a

5-6

Page 61

Space Lorps “ CHAPTER 5 — SCHEMATIC DIAGRAMS

” _ tax Ths Gx SE ee Or

3] % rer ae F/O teveg Fie ao] oo

=i a

“oe ey

a in an os E]oe our f 2103 Z] OF Ren Ru

  • ined ae et] ao : ae) ie zh dee “ioe

”

: ae

t He z fs on . no

1. 24s = viaae ate “toe

Figure 5-1 Space Lords Game PCB (GX2) Assembly Schematic Diagram A049809-XX E

5-7

Page 62

Cnarter 5 — SCHEMATIC DiAGRAMS “ Space LorDs

osu

oy

nwt

nev

a

“0

ov

“0

ce

GND and ACND +

5-8 a FB oe —om ae: ‘MTC HOLE e OME wae OM TE noe the ATG oe " HVE Le, J8PKR

2 Oe spar, DO SPKREL Ker Wo 5 O—* SPKRER 6 Oe SPKR-R

ete dear Le: coed I? T+ T

an ot eee soot 2 anton:

Fisa06 cc.k wn Leo com i ry —

ono et.

dointernally nec MSM6Z495s a

Page 63

Space Lorps & CHAPTER 5 — SCHEMATIC DIAGRAMS

er we SW cea, ru. fp

m7 ne wit

wy ov

_! “wy wz

Wire bein ee_| rr ‘ROR Bs

Fra PS a ss soode top oat tteco sogttro rattan: soz#s ep atte 2 soaéiisy sapiens soveets> Saft sos sosettan — salSos. soees20 zaps 7 soreSfip__saf® 7 7 Tae

BYPASS

Figure 5-2 JSA3S PCB Assembly Schematic Diagram +0

a

it ey vod feo ante sp0 beet dia tate ape pease SobesSh deo betes deste aapesane proztis ist ES57 csr

A049953-XX A sz “ve f pb] -sv 1 rbieoan |

SPRRER

sey

oy

ow i

5-9

Page 64

Carter 5 — SCHEMATIC DIAGRAMS ¢% SPACE LoRDS

wey Rez 40K am _[o

mrFuaye

——J is FOr + BT oe |e oz Ss Hers pup1o sovep gh] nc

od re a Pseasese
alexA138 ZS lay BONE.Aue
suey 78 so ats LEi2BeZlaiz 20SALL
EZ] qoy ataSua ZS lagsao 8
atAtomB

oy o_o sae mo Slay sor

eSarc

ea ses

aaee
—ata

<™ s% sf a8 fo

wotna

se 164 5 ae 5 a 7 ER or ssl jae tar 2 doe Spe fom ass

5-10

Page 65

Space Lorps % CHAPTER 5 — SCHEMATIC DIAGRAMS

‘sace:4s9

ATR 2noau> WATE CZa04H? WE czan2W) waU__ c2A00M2 TRORK (20688) OID od < 2008) cze0eR) c2800R> « mo wal Ss ones onal? 7B ax raliesonraeo 1 Tal bbe puees

fo °° Gores© (aLSSbias
SeNs> sap 42S oxtaSs sa BS overs
ort¢ortz
tofSeso fatSov
Sere SotSeeaso
Es csS ifSOL ¥FaBerar
SinhaStatape
i faphoorei fal?Sbucce

HCTE73 kook) acres wore ft rear

1x Prey 1 rab oveee © apSlias fs SabsES ovens om ET safes ovene Saat cunt i iaLESbiees CX cow | werer3

sor0:72

Figure 5-2 JSA3S PCB Assembly Schematic Diagram A049953-XX A.

5-11

Page 66

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 67

Space Lorps % CxapvER 5 — SCHEMATIC DIAGRAMS

orcn. eagiwl, oe fiz i ia i a cali uooun. my ss

oNthaopat

:

am3.spun

mae pony Pan

onLosNose

wr

peerTier3
REND © TageB=AUX INare

ur awe n0PoHR egy el_ ssi re. $j

searen
wabtera:uote

m on ne #224 en Uses

wildars]?sl.

a se

7i1
2Ur009Sioer + Sbboer

: |

eel.reno e—ceceshfizAN

er

ane ett

coun.xtsuocure

oo fs ae ovcus ep aamen ht aa ovces 4 bral R102 cucu «| samen ag ovens of oe 294 utes wf SERRE aR ovens af , 1

se?asew
ucts » f aieada hts agovces x {Huaang
2°aoeran
sveus 2 {TEreagentovens {EN
ueR08alRIBUS
ouces » LEE aggovens 2 Paang
oe20 Be“
wiyaasor | asthasuo
suc.g wa HE agsveny«aRrag=)ai

or.ne e224, 2 or 1F" a, rere ns $——p« RUDL t Ra REZ foe #1

ror. a

Figure 5-2 JSA3S PCB Assembly Schematic Diagram 404995: XK A, Ree

5-13

Page 68

CHarreR 5 ~ ScueMatic DiaGRams ¢ Space Lorps

5-14

Taefeahs

COBLERT He sews ceecerre] #9} *

Les ees vena

ee

“air eat n

1%career10 6g‘COMMDECODE
FeCrna=] 1 2595 99 | 22 a ace

or Datos 211s ves fas Sopaecss Seuecrs

uatetans14 roe HB coor
0bwarT 6 re
.vmvue—e]iz TouLorene‘
aaaeer) TameeteeAopRess sexrcrs

oe ‘SOCKET. one HE col

ut = TWebr ty

vee AgerLees"2xb 002157

Ime pg 2t_t202

ly ar he afte te Ss

a ar Br Pe pss eB ns 83 ne Be a Pee ses career le] Veo = LS¥

Page 69

Space Lorps “ CHAPTER 5 — SCHEMATIC DIAGRAMS

ot0:151 cyt nimi SE a 7 i00eF Eatery KAZ cern sr oan 5 oyun ans oo nine iar

ofa raswornoF

olin rl Soar er comet ese wo OHS wer oS uae feat eer | cecmirite 5 Sami wear of ig¢ oe Z i 8 bat) a pat! tye ow ott wate 2S pest caer, | oloinas Seems RE Sekar eed, = ratio nv of» er,

27RNAISe

0 ore abr 2 neon ae Set thot rane 32s mot wer | perme SE mee PT Sates eet

SeinaeJE

oe Rx?

Figure 5-3 CLARN II PCB Assembly Schematic Diagram A051092-XX D L828, Axoc0:159

Vee = RSV

5-15

Page 70

(CHAPTER 5 — SCHEMATIC DiaGrams @ Space Lorns

5-16 Lewes

me oD x

i oR abe Trees ne a

wr

$5 l4q

OND tn Tien

i oo a és

R31 ae

z

Looe

*

' : Ley = flee ; KEY eK

‘ : = : 3 1 a on dex tow

spi Lesy

i es

£36

233 co iK Te pe ono

Page 71

Space Lorps ¢ CHAPTER 5 — SCHEMATIC DIAGRAMS

so none Lxat ——4 100 SACRESET caste ——_18

ee

Loaner ey easter F00 ‘3 O—« MOTORS 10K 6 Oe roToRE. <s

ue.

COMM LINK

m3 ov ewe BERSTER aesv yn

RIGHT sre souRCe: RIGHT 15 ALARYS SLAVE

Figure 5-3 CLARN II PCB Assembly Schematic Diagram A051092-XX D

5-17

Page 72

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 73

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 74

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 75

Space Lorps % CHAPTER 5 — SCHEMATIC DIAGRAMS

ehaoune rom aw ov co P2

R2] key+2v TE
=1] 45voxo | 2 | 86 ——}

2|43v enn | 3

BH4 | oND<{
aN5| GND>ey
oe8 | onoTHeAy PONER
s7] ono2,8SUPPL
211] +12v,3
12] +12vi4
xreH
2onPc 7}
smBas) 2LB

xD sv] 3

ssw8wiv [4PBB

Key nD | 5

4iono Ls | **
aPe\
§aotx

& soizb¥ -sv/3 +5v ee +5v/5 asv [6 —___|

Figure 5-5 Space Lords Game Wiring Diagram 050670-01 C

5-21

Page 76

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 77

Space Lorps ¢ CHAPTER 5 — SCHEMATIC DIAGRAMS

auvog 1h OL BAY ‘ayvog 1HON 3NO UAV

«7 =

>[>p-18|

a] Bu XZ7 a = y La $/

r i i as a a P50

Figure 5-5 Space Lords Game Wiring Diagram 050670-01 C

5-23

Page 78

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 79

Space Lorps # CHAPTER 5 — SCHEMATIC DIAGRAMS

'SWGND RIGHT COIN SW LEFT COIN SW

GND 45V AC CHASSIS GND eerousens OR NOS~.¢ BK Right Coin Switch NC Y_NO. c BK

Left Coin Switch ' i NC

Figure 5-7 Coin Door Wiring Diagram 4037542-XX F

5-25

Page 80

Cuarter 5 — SCHEMATIC DiAGRAMS “% Spack LORDS

wv iS on

Page 81

A Space Lords” Statistics Sheet

ATARI

GAMES

Location: Date Recorded:

Meter:

Left Coins:Melee Minutes:Total Coins;
Right Coins:Pilot Coins:Average Time/Credit:—
Idle Minutes:Copilot Coins:Percentage Play:

1-Player Minutes: New Games: 2-Player Minutes: _ Continued Games: Solo Minutes; Error Count: Team Minutes;

Divide By Zero: Privilege Violation: Chk Instruction: A to D Timeouts: Trap V Instruction: Watch Dog Resets: Address Errors: Illegal Instruction:

Continued on back page =

Page 82

M Space Lords" Statistics Sheet ATARI GAMES

Time Per Life for Solo (Secs.)

0-19 20-29 30-39 40-49 50-59 60-49 70-79 80-89 90-99 100-109 110-119 120-129 130-139 140-149 150-159 160-169 170-179 180-189 190-199 200 & up PUTT Total Median (Continued)

Time Per Life for Team (Secs.)

0-19 20-29 30-39 40-49 50-59 60-69 70-79 80-89 90-99 100-109 110-119 120-129 130-139 140-149 150-159 160-169 170-179 180-189 190-199 200 & up PTET Total Median Time Per Life for Melee (Secs.)

0-29 30-59 60-89 90-119 120-149 150-179 180-209 210-239 240-269 270-299 300-329 330-359 360-389 390-419 420-449 450-479 480-509 510-539 540-569 570 & up PTAA Total Median

Session Times (Minutes) 10-11 12-13 14-15 16-17 18-19

20-21 22-23 24-25 26-27 28-29 ITE ITT 30-31 32-33 3435 36-37 38 & up TTT Total Median

Page 83

feel pel el pel el pele feted fel el feted pel fel fel felled pelea felled el feted pelfelelfelrey [ca

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displ: and video-dise players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse. neglect. alteration. improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Excepl for any express warraity set forth in a written contract between Seller and Buyer which coutract supersedes the terns berein, this warranty is expressed in lien of all otber warranties expressed or implied. including the

implied warranties of merchantability and fitness for a particular purpose,

and of all other obligations or liabilities on the Seller's part, and it neither assumes nor autborizes any otber person to assume for the Seller any other liabilities in connection with the sale of products by Seller. Pree eee eee eteelele ele erelel ele elrelrel elated pele ele fel pel fel fell

The use of any non-Atii parts may void your warranty, according to the terms of the warranty. The use of ny non-Atii parts may also adversely affect the safety of your oth Be very cautious in using non-Atari-supplied adler to en your safety game and cause injury t you components with our Atari distributors are indep tely owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible tor the quality. suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor

Page 84

ATARI GAMES CORPORATION ib75 Syesrnore Drive Milpitas, CA 95035