18 Wheeler STD
18 Wheeler: American Pro Trucker (deluxe, Rev A) (Sega, 2000) · Manual · 85 pages · 51 sections · original scan
pane 183 unesuen
STD VERSION
OWNER’S MANUAL
SEGA ENTERPRISES, INC. USA
MANUAL NO. 999-0921
Warranty
Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.
Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.
Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.
Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.
This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.
TABLE OF CONTENTS
INTRODUCTION OF THE OWNERS MANUAL GENERAL PRECAUTIONS . PRECAUTIONS TO BE HEEDED FOR OPERATION . NAME OF PARTS . ACCESSORIES . ASSEMBLY AND INSTALLATION . PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE . CONTENTS OF GAME . EXPLANATION OF TEST AND DATA DISPLAY 7-1 SWITCH UNIT AND COIN METER 7-2. SYSTEM TEST MODE A CR.T. TEST B COIN ASSIGNMENTS 7-3 GAME TEST MODE A INPUT TEST B OUTPUT TEST C SOUND TEST D VOLUME SETTING E GAME ASSIGNMENTS F BOOKKEEPING G BACKUP DATA CLEAR
- HANDLE MECHA 8-1 REMOVING THE CONTROL MECHANISM 8-2 VOLUME ADJUSTMENT/REPLACEMENT
- SHIFT LEVER 9-1 REMOVING THE SHIFT LEVER 9-2. SWITCH REPLACEMENT
- ACCELERATOR & BRAKE 10-1 REMOVING THE ACCELERATOR AND THE BRAKE 10-2 ADJUSTING OR REPLACING THE VOLUME 10-3 GREASING
- COIN SELECTOR
- MONITOR 12-1 CAUTIONS/WARNINGS FOR HANDLING 12-2 CAUTIONS TO BE HEEDED WHEN CLEANING 12-3 ADJUSTMENT METHOD
- REPLACEMENT OF FLUORESCENT LAMP AND BUTTONS
- PERIODIC INSPECTION TABLE
- TROUBLESHOOTING
- GAME BOARD 16-1 LOCATING THE GAME BOARD 16-3 COMPOSITION OF THE GAME BOARD
- DESIGN RELATED PARTS
- PARTS LIST
- WIRING DIAGRAMS NAWRWNE
SPECIFICATIONS
Installation space: 34 in.(W) x 71 in.(D)
Height: 76 in.
Weight: Approx. 450 lbs.
Power maximum current: 5 Amp AC 120V 60 Hz
MONITOR: 29” COLOR MONITOR
INTRODUCTION OF THE OWNERS MANUAL
SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to 18 WHEELER ‘AMERICAN PRO TRUCKER’ STD TYPE, a new SEGA product.
This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.
SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 415-701-6580 Fax 415-701-6594 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday
General Precautions
Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in arisk of fire or electric shock.
Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
- If the power cord or plug is damaged;
- If liquid has been spilled, or objects have fallen into the product;
- If the product has been exposed to rain or water;
- If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
- If the product has been dropped or damaged in any way;
- When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below:
- Places subject to rain/water leakage, or condensation due to humidity;
- In close proximity to a potential wet area;
- Locations receiving direct sunlight;
- Places close to heating units or hot air; ¢In the vicinity of highly inflammable/volatile chemicals or hazardous matter;
- On sloped surfaces; In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
- Places subject to any type of violent impact;
- Dusty places.
INSTALLATION PRECAUTIONS
- Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.
- Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.
- Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). ¢ For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).
REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.
LISTED
5K92
AMUSEMENT MACHINE
1 .PRECAUTIONS TO BE HEEDED FOR OPERATION
In order to prevent accidents, be sure to comply with the following points before and during operation.
PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION
A
Do not climb on the product. Climbing on the product can cause falling accidents. To check the top portion of the product, use a step. @ To avoid electric shock, check to see if door & cover parts are closed.
@ To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product:
Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.
To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others and result in injury or trouble.
PRECAUTIONS TO BE HEEDED DURING OPERATION
- Intoxicated persons
- Those who have high blood pressure or heart problems.
- Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.
- Persons susceptible to motion sickness.
- Persons whose acts runs counter to the products warning displays.
- Instruct those who wear high-heeled shoes to refrain from playing the game by explaining that playing the game with highheeled shoes is very dangerous and likely to cause a potentially hazardous situation.
@ To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in openings of the product or small openings in or around doors.
To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason. Although this product has the accident preventive covering attached to potentially hazardous places where hand and fingers could be caught, small children are unable to perceive hazards. Use care so that small children do not come close to the product when in play. Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage and/or falling down, resulting in injury due to fragments and falling down.
2 .NAME OF PARTS
CONTROL PANEL
GAME SPECIFICATIONS WIDTH in. LENGTH in. HEIGHT in. WEIGHT Ibs.
All measurements are and rounded UP DURING SHIPPING 40” x 7” x 84” 500 LBS.
WHEN ASSEMBLED 34” xX 71” xX 76” 450 LBS.
- ACCESSORIES
DESCRIPTION Part No. (Qty.)
Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you.
TAMPERPROOF WRENCH M8 540-0009-01 (1) TOOL KEY MASTER KEY 220-5576 (2) (2) For the CASHBOX DOOR For opening/closing the doors
THE SHIPMENT METHOD DESCRIBED BELOW ONLY APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE
CAUTION! FOLLOWING GAMES:
LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2 HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, HOUSE OF THE DEAD 2, OCEAN HUNTER, STAR WARS TRILOGY, ZOMBIE REVENGE, CRAZY TAXI, ARILINE PILOTS, 18 WHEELER
NINE VER SAHTP MODEL 3 / NAOW
SO0ARDS OUTSIDE OF C
CARTON BOX 601-8928 (1) Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}
DO NOT SHIP GAME BOARD WITHOUT THIS BOX AS IT MAY DAMAGE THE GAME BOARD AND VOID YOUR WARRANTY.
“CHECK SIDE” Display
FILTER BOARD
THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM
h NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS
WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.
- ASSEMBLING AND INSTALLATION
Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the
When carrying out the assembly work, follow the procedure in the following 5-item sequence:
1 | ASSY OF THE CABINET
2 SECURING IN PLACE (ADJUSTER ADJUSTMENT)
3 | POWER SUPPLY
4 | ASSEMBLING CHECK
ote that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.
1 ASSY OF CABINET
A Permanantly tightening the hex bolts should not be completed until
the leg levelers are adjusted properly.
SECURING IN PLACE (ADJUSTER ADJUSTMENT)
Be sure to have all the Adjusters make contact with the floor surface. Unless the Adjusters come into contact with the floor surface, the W a Cabinet can move of itself, causing an accident.
This machine has 4 each of casters and adjusters (shown below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.
® Move the machine to the installation position. Be sure to provide adequate space allowing the player to get on and off.
Q Have all of the Leg Adjusters make contact
with the floor. Adjust the height of the Leg Adjusters by using a wrench so that the machine's position is kept level.
@ After making adjustments, fasten the leg
Adjuster Nut upward and secure the height of the Leg Adjuster.
POWER SUPPLY
@ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. @ Ensure that the wiring position is not in the customer's passage way
Connect the game to the power supply and turn on power to the game. Before connecting power supply be sure that power switch is off
Q@) Turning the AC unit’s main switch on will cause the machine
to start the power check and network check automatically.
Q) In the Power On check, the steering wheel turns left and right, (105
and then returns to the centering position and stops. In this i
check, the values of the VR inside the control panel are ° ° corrected.
@ Until this check is finished, and the steering wheel stops, do E (7) If you do, the steering reaction during the game (reaction at Vas
not touch the steering wheel or play the game.
. : . . ° °
In the case of an abnormal reaction during the game, turn 1B ee ee el the time of course-out or crash) can not be obtained correctly. ~ <\ power on again from the beginning and complete the power on. \ check. Coon102)
ASSEMBLING CHECK
In the TEST MODE, ascertain that the assembly has been made correctly and that the IC BOARD is satisfactory. In the test mode, perform the following test:
- MEMORY TEST
MEMORY TEST MODE . . Selecting the RAM TEST item on the test mode menu screen causes the on-board memory to be RAM TEST tested automatically. The game board is satisfactory if the display beside each IC No. shows |C29 GOOD GOOD. IC34 GOOD IC16 GOOD IC18 GOOD IC20 GOOD IC22 GOOD Icg9_ GOOD IC10 GOOD IC11 GOOD IC12 GOOD
PRESS TEST BUTTON TO EXIT
- CR.T. TEST
CRIT.TEST 1/2
In the TEST mode menu, selecting C.R-T. TEST RED allows the screen (on which the monitor is tested) to be displayed. Although the monitor adjustments have been made at the time of shipment from the GREEN factory, color deviation, etc., may occur due to the effects of geomagnetism, the location of the building’s steel frames and other game machines ios in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the monitor by refering to Chapter 12. WHITE
PRESS TEST BUTTON TO CONTINUE
BLTEST22
PRESS TEST BUTTON TO EXIT
- INPUT TEST
INPUT TEST
COIN CHUTE #1 OFF COIN CHUTE #2 OFF SERVICE OFF TEST OFF START OFF VIEW OFF HORN OFF SHIFT [L] OFF SHIFT [H] OFF SHIFT [R] OFF HANDLE XXH ACCEL XXH BRAKE XXH
PRESS TEST + SERVICE BUTTON TO EXIT
- OUTPUT TEST
OUTPUT TEST
START LAMP OFF VIEW LAMP OFF HORN LAMP. OFF ROLL LEFT OFF ROLL RIGHT OFF
->EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
- SOUND TEST
SOUND TEST
B.G.M. 0/ XX EFFECT O/ XX ICS (I 0/ XX
> exit
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON Selecting the INPUT TEST on the test mode menu screen carses the screen (on which each switch is tested) to be displayed. Press each switch. For the coin switch test, insert a coin into the coin inlet with the coin chute door open. If the display beside each switch indicates “ON,” the switch and wiring connections are satisfactory.
Select OUTPUT TEST from the menu in the test mode to cause the screen (on which each lamp and wiring connection is tested) to appear. Ensure that each lamp lights up satisfactorily.
In the TEST mode, selecting SOUND TEST causes the screen, on which sound related BD and wiring connections are tested, to be displayed. Be sure to check if the sound is satisfactorily emitted from each speaker and that the sound volume is appropriate.
Perform the above inspections also at the time of monthly inspection.
5 .PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE
AN
Do not push on the plastic parts. Doing so may damage the parts and cause injury due to fragments resulting from damage.
Do not push the cabinet from the left/right direction,
6 .CONTENTS OF GAME
The following explanations apply in the event the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occured. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.
When the product is energized, the Billboard’s fluorescent lamp is always lit. During the advertise mode, the advertise screen is shown on the monitor and sound is emitted from the speakers. Setting to No Sound Output during the advertise mofr is possible in the TEST mode.
OUTLINE OF THE GAME
- This is a single, driving game in which the player competes with rivals by driving a Trailer Truck to cross America.
- When coins are inserted to gain credits, the START button starts flashing. Press the START button to proceed to the SELECTOR mode where you can select your truck and the trailer. The game starts upon selecting the truck and the trailer.
Based on the setting made in the test mode, the number of coins inserted to obtain a credit counts as one credit in this product. The number of credits necessary to start the game and to continue the game can be set in the test mode.
- The game consists of the 4 kinds of driving stages and 3 kinds of parking stages (Bonus stages).
- When continued, the game is played at the beginning of the last stage that resulted in a game over.
- If your score falls within the top 5, you can enter your name.
CONTENTS OF THE GAME
+ Pass the checking point within a certain period of time and reach the goal, and you can clear the stage.
+ The game finishes after clearing all 4 stages.
+ If you can reach the goal ahead of your rival trailers in each stage (the Ist through the 3rd), then you can. play the Parking game (Bonus game).
GAME OVER
- If you fail to pass the checking point within a certain period of time or fail to goal, the game is over.
+ Passing the checking point behind the rival trailers or failing on the Parking game does not result in a game
over.
OPERATION
<STEERING WHEEL> SELECTOR — : Turn right or left to select an object. GAME PLAY : Operate the Trailer Truck. <HORN AT THE DRIVER’S SEAT> SELECTOR _ : Decide GAME PLAY : Blow the horn to signal the car ahead to move out of the way or to have it increase the speed. Have the trailer ahead increase the speed. <ACCEL.> SELECTOR _ : Decide GAME PLAY : Increase your Trailer Truck speed, or stop it. <BRAKE> SELECTOR - : Void GAME PLAY : Decrease your Trailer Truck speed, or stop it. <GEAR> SELECTOR - : Void GAME PLAY : 3-position, HI (High), LOW, R (Reverse) <VIEW CHANGE> SELECTOR - : Void GAME PLAY : Select either Driver’s View or Bird’s View. <START BUTTON> The START button flashes when the number of coins that are worth one credit are inserted. While flashing, press the START button to proceed to the SELECTOR. It also flashes when one or more credit(s) remains after the game is over.
SELECTOR
MITRUCK SELECT
Select the truck from among ASPHALT COWBOY, STREAMLINE, HIGHWAY CAT, LONG HORN, and NIHONMARU. Each truck’s abilities in SPEED, TORQUE, and TOUGHNESS differ.
isa LAS) PHATE WIB.ON
METRAILER SELECT When starting in stage 2, 3, or 4, select the trailer for towing from the 2 trailers. The weight, the length, and the transportation fee differ. The heavier the trailer, the more the difficulty.
TRAWPORT HEM $ 12600
NAME ENTRY
Tf your score falls within the top 5, you can enter your name.
als (EOIN Si COLIN
VIEWING THE GAME SCREEN |
REARVIEW MIRROR
DESTINATION
TIME LIMIT RANSPORTATION
FEE
TACHOMETER
<DESTINATION>
Name of the destination point.
<TIME LIMIT>
Indicates the player’s playable time. Additional time will be added when passing the CHECKPOINT and obtaining TIME BONUS.
<REARVIEW MIRROR> Indicates the rear condition while the DRIVER’S VIEW is selected.
<TRANSPORTATION FEE>
Indicates the fee you receive when you reach the destination. If you damage the trailer by hitting another car, etc., the fee will be reduced.
<TACHOMETER>
Indicates the speed of rotation.
<GEAR CHANGE INDICATOR>
Indicates the gear condition (4 positions total) with the lamp on the monitor.
<GEAR CONDITION> Indicates the current gear condition. The three types of gears (REVERSE - LOW - HI) are avail able.
7 .EXPLANATION OF TEST AND DATA DISPLAY
By operating the switch unit, periodically perform the tests and lata check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checks in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.
A NAOMI GAME BOARD is used for this product. This game oard system allows another game board to be played by replacing the ROM Board Case mounted on the NAOMI CASE. As such, the test mode of this system consists of the System Test Mode for the system to execute SELF-TEST, COIN ASSIGNMENTS, etc. used in common for the machines employing the NOMI BOARD, and the Game Test Mo to execute Input/Output test for the operation equipment, difficu ode for the specific product ty setting, etc. In this manual, explanations regarding the System Test Mode cover the settings for this product only. For the details of the System Test Mode, refer to the NAOMI SERVICE MANUAL.
TABLE EXPLANATION OF TEST MODE
ITEMS DESCRIPTION CHAPTERS
When the machine is installed, perform the following: INSTALLATION | |. Verify that each setting is per the standard settings at the SERVICE MANUAL] OF MACHINE time of shipment.
- Check all Input equipment in the INPUT TEST mode. TA
- Check all OUTPUT equipment in the OUTPUT TEST mode. 3
- In the MEMORY TEST mode, check ICs on the IC Board. 41
MEMORY This test is automatically executed by selecting RAM TEST or ROM | SERVICE MANUAL BOARD TEST in the Menu mode.
| PERIODIC | Periodically perform the following: | SERVICE MANUAL] |
| SERVICING | 1. MEMORY TEST | 41 |
- Ascertain each setting. 41
- Test all Input equipment in the INPUT TEST mode. TA
- Test all Output equipment in the OUTPUT TEST mode. 3
| CONTROL | 1. Check all Input equipment in the INPUT TEST mode. | SERVICE MANUAL] |
| SYSTEM | 2. Adjust or replace all Input equipment. | 733, F |
- If the problem remains unsolved, check the movement of each 10, , 2 control mechanism.
| MONITOR | In the MONITOR ADJUSTMENT mode, check to see if the | SERVICE MANUAL] |
MONITOR adjustment is appropriately made. R
| IC BOARD | 1. MEMORY TEST | SERVICE MANUAL} |
2.In the SOUND TEST mode, check the sound related ROMs. 41, 7-3C
| DATA CHECK | Check such data as game play time and histogram to adjust the | SERVICE MANUAL] |
difficulty level, ete TRE
7-1 SWITCH UNIT AND COIN METER
Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit.
@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ If the COIN METER and the game board are electrically disconnected,
Open the COIN CHUTE DOOR, and the switch unit shown will appear. The function of each switch is as follows:
SWITCH UNIT _— SPEAKER VOLUME
TEST BUTTON
SPEAKER VOLUME SPEAKERS at th CONTROL PANEL left & SERVICE BUTTON right.
| SPEAKER Ps TEST SERVICE
SPEAKER VOLUME (SPEAKERS) Controls the sound volume for the left/right CONTROL PANEL speakers. SPEAKER VOLUME (SUPER WOOFER) Controls the sound volume for the SUPER WOOFER and the BASE SHAKER under the seat. TEST BUTTON (TEST SW) Enters to the test mode. SERVICE BUTTON (SERVICE SW) Gives credits without registering on the coin meter. OOOO
COIN METER
Open the Cashbox Door by using the key to
have the Coin Meter appear underneath the COIN METER rc)
Cashbox.
COIN METER
7-2 SYSTEM TEST MODE
eo)
TEST mode is finished, the contents of the setting changes do not take effect. eExecuting “BACKUP DATA CLEAR” in the SYSTEM TEST MODE does not clear the BOOKKEEPING data in the GAME TEST MODE. Entering the TEST mode clears fractional numbers of coins less than one credit and BONUS ADDER data.
The SYSTEM TEST mode mainly allows checks of the IC Board for accurate functioning , monitor adjustment, as well as CRT TEST and COIN ASSIGNMENTS, etc. The following assignments, however, should be designated for this product.
CABINET TYPE : 1 PLAYER (S) MONITOR TYPE : HORIZONTAL
SERVICE TYPE : COMMON
COIN CHUTE TYPE : COMMON ooo
TEST ITEM SELECT
SYSTEM MENU
RAM TEST JVS TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS BOOK KEEPING BACKUP DATA CLEAR CLOCK SETTING
ROM BOARD TEST GAME TEST MODE [18 WHEELER]
- >EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
- After turning the power on, press the TEST button to display the test item menu shown above.
@ Press the SERVICE button to move the arrow to the desired item and press the TEST button.
- When finished, bring the arrow to EXIT and press the TEST button to return to the Game mode.
A] C.R.T. TEST
- RGB COLOR ADJUSTMENT SCREEN In this screen, monitor color can be checked.
CRT. TEST 1/2 Each of red, green, and blue is the darkest at the leftmost end, and becomes brighter towards the aeD right-hand end in 31 gradiations. Monitor brightness is satisfactory if the white color bar is black at the left end and if it is white at the right end. Press the TEST button to proceed to the next screen. GREEN
BLUE
WHITE
PRESS TEST BUTTON TO CONTINUE
- MONITOR SIZE ADJUSTMENT SCREEN In this screen, monitor size can be checked.
CRT TEST 22 Adjust the crosshatch frame line so that the checkered pattern does not extend beyond the screen. Press the TEST button to return to the menu mode.
PRESS TEST BUTTON TO EXIT
a COIN ASSIGNMENTS
The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”
SETTING CHANGE PROCEDURE
Gror) Setting changes cannot be stored unless the TEST BUTTON is pressed
while the arrow is on EXIT.
® Press the SERVICE BUTTON to move the arrow to the desired item.
@ Change the desired item setting by using the TEST BUTTON.
® To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.
COIN ASSIGNMENTS,
COIN CHUTE TYPE COMMON (A) COIN/CREDIT SETTING #1 (B) COIN CHUTE #1 1 COIN 1 CREDIT
COIN CHUTE #2 1 COIN 1 CREDIT
MANUAL SETTING (C) SEQUENCE SETTING (D) -> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
(COMMON SETTING)
(A) COIN CHUTE TYPE (COMMON, INDIVIDUAL) Set to COMMON.
Up to 2 Coin Chutes (#1 and #2) can be used and also, (B) COIN/CREDIT SETTING ratio can be set seperately for #1 and #2.
(B) COIN/CREDIT SETTING (#1 ~ #27) Sets the credit increase increment per coin insertion. There are 27 settings from #1 to #27, expressed inOO credit(s) as against OOcoins inserted. #27 refers to FREE PLAY.
(C) MANUAL SETTING
The Credit’s incremental increase settings as against a coin insertion are shown in further details than in (B) above (refer to Table 2). Also, note that when this MANUAL SETTING is performed, (B) COIN CREDIT setting becomes ineffective.
MANUAL SETTING
COIN ASSIGNMENTS MANUAL SETTING
COIN TO CREDIT 1 BONUS ADDER NO BONUS ADDER COIN CHUTE #1 MULTIPLIER 1 COIN COUNT AS 1 COIN COIN 123456789 CREDIT 123456789
COIN CHUTE #2 MULTIPLIER 1 COIN COUNT AS 1 COIN COIN 123456789 CREDIT 123456789
SEQUENCE SETTING
-> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
(D) COIN TO CREDIT Determines COIN/CREDIT setting.
(E) BONUS ADDER
This sets how many coins should be inserted to obtain one SERVICE COIN.
(F) COIN CHUTE (#1/#2) MULTIPLIER
This sets how many tokens one coin represents. (D) (E) (F)
(F)
(@)
Table 1: COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)
SETTING FUNCTION OF CHUTE#1
| SETTING #1 | 1 COIN | 1 CREDIT. |
| SETTING #2 | 1 COIN | 2 CREDITS |
| SETTING #3 | 1 COIN | 3 CREDITS |
| SETTING #4 | 1 COIN | 4 CREDITS |
| SETTING #5 | 1 COIN | 5.CREDITS |
| SETTING #6 | 1 COIN | 2 CREDITS |
| SETTING #7 | 1 COIN | 5 CREDITS |
| SETTING #8 | 1 COIN | 3 CREDITS |
| SETTING #9 | 1 COIN | 4 CREDITS |
| SETTING #10 | 1 COIN | 5.CREDITS |
| SETTING #11 | 1 COIN | 6 CREDITS |
| SETTING #12 | 2 COINS | 1 CREDIT. |
| SETTING #13 | 1 COIN | 1 CREDIT. |
| SETTING #14 | 1 COIN | 2 CREDITS |
| SETTING #15 | 1 COIN | 1 CREDIT |
2 COINS 3 CREDITS
| SETTING #16 | 1 COIN | 3 CREDITS |
| SETTING #17 | 3 COINS | 1 CREDIT. |
| SETTING #18 | 4 COINS | 1 CREDIT. |
| SETTING #19 | 1 COIN | 1 CREDIT |
2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5.CREDITS
| SETTING #20 | 1 COIN | 5.CREDITS |
| SETTING #21 | 5 COINS | 1 CREDIT. |
| SETTING #22 | 1 COIN | 2 CREDITS |
| SETTING #23 | 2 COINS | 1 CREDIT |
4 COINS 2 CREDITS 5 COINS 3 CREDITS
| SETTING #24 | 1 COIN | 3 CREDITS |
| SETTING #25 | 1 COIN | 1 CREDIT |
2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS
| SETTING #26 | 1 COIN | 1 CREDITS |
SETTING #27 FREE PLAY
Table 2: MANUAL SETTING
COIN TO CREDIT 1 COIN 1 CREDIT 2 COINS 1 CREDIT 3 COINS 1 CREDIT 4 COINS 1 CREDIT 5 COINS 1 CREDIT 6 COINS 1 CREDIT 7 COINS 1 CREDIT 8 COINS 1 CREDIT 9 COINS 1 CREDIT
BONUS ADDER NO BONUS ADDER 2_ COINS GIVE 1 EXTRA COIN 3 COINS GIVE 1 EXTRA COIN 4 COINS GIVE | EXTRA COIN 5 COINS GIVE | EXTRA COIN 6 COINS GIVE 1 EXTRA COIN 7 COINS GIVE | EXTRA COIN 8 COINS GIVE 1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN
COIN CHUTE (#1/#2) MULTIPLIER 1 COIN COUNTS AS_1 COIN 1_ COIN COUNTS AS_2_ COINS 1 COIN COUNTS AS_3 COINS 1 COIN COUNTS AS_4 COINS 1 COIN COUNTS AS_5_ COINS 1 COIN COUNTS AS _ 6 COINS 1_ COIN COUNTS AS_7 COINS 1 COIN COUNTS AS_8 COINS 1 COIN COUNTS AS_9 COINS
(G) SEQUENCE SETTING
Number of credits required for starting a game, etc. can be set. Each sequence can be set between | ~ 5 credit(s).
COIN ASSIGNMENTS SEQUENCE SETTING
SEQUENCE 1 2 CREDIT(S) SEQUENCE 2 1 CREDIT(S) SEQUENCE 3 1 CREDIT(S) SEQUENCE 4 1 CREDIT(S) SEQUENCE 5 1 CREDIT(S) SEQUENCE 6 1 CREDIT(S) SEQUENCE 7 1 CREDIT(S) SEQUENCE 8 1 CREDIT(S) EXIT [XXXXX XXXXX XXXXX XXXXX] DESCRIPTION OF SEQUENCE 1 CREDIT TO START 2 CREDIT TO CONTI NUE 3 NO USE 4 NOUSE 5 NO USE 6 NO USE 7 NOUSE 8 NOUSE
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
SEQUENCE 1: Number of credits required for game to start. SEQUENCE 2: Number of credits required for CONTINUE. SEQUENCE 3 ~ 8: NOT USED.
7-3 GAME TEST MODE
MENU MODE
SYSTEM MENU 18 -WHEELER TEST MENU
RAM TEST INPUT TEST JVS TEST OUTPUT TEST SOUND TEST SOUND TEST C.R.T. TEST C.R.T. TEST SYSTEM ASSIGNMENTS GAME ASSIGNMENTS COIN ASSIGNMENTS => VOLUME SETTING
BOOKKEEPING BOOK KEEP ING
BACKUP DATA CLEAR BACKUP DATA CLEAR CLOCK SETTING -> EXIT
ROM BOARD TEST -> GAME TEST MODE [18 WHEELER] EXIT
SELECT WITH SERVICE BUTTON SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON AND PRESS TEST BUTTON
SYSTEM TEST MODE MENU GAME TEST MODE MENU
Press the TEST button to display the SYSTEM TEST MODE MENU.
By pressing the SERVICE button, move the arrow (->) to select the GAME TEST MODE.
Press the TEST button to enter GAME TEST MODE. The screen displays the GAME TEST MODE
MENU.
By pressing the SERVICE button, move the arrow (->) to select the desired item. Press the TEST button to
execute the selected item.
¢ Select EXIT and press the TEST button to exit from the GAME TEST MODE and return to the SYSTEM
TEST MODE MENU. Further, select EXIT and press the TEST button to finish SYSTEM TEST MODE
and return to the normal mode.
A. INPUT TEST
Select INPUT TEST to have the screen shown below appear and to observe the status of each switch on the Control Panel. In this mode, Periodically check the status of each switch.
INPUT TEST
COIN CHUTE #1 COIN CHUTE #2 SERVICE TEST START VIEW HORN SHIFT [L] SHIFT [H] SHIFT [R] HANDLE ACCEL BRAKE OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF XXH XXH XXH
PRESS TEST AND SERVICE BUTTON TO EXIT
B. OUTPUT TEST e By pressing each switch, if the display on the right-hand side of the name of each switch changes from OFF to ON, the SW and the wiring connections are satisfactory. Operate CONTROL WHEEL, THRUST LEVER, etc. to check Volume value display variation.
@ To check COIN CHUTE 1 & COIN CHUTE 2, open the COIN CHUTE DOOR and insert a coin(s) in the slot.
@ “HORN?” is for the driver seat and the assisstant driver seat. Because the same circuit is used for the HORN in both seats, if the switch and the wiring connection are satisfactory, pressing the HORN at either side changes the display from OFF to ON.
@ For the steering wheel, the accelerator, and the brake, operate each input device and check to see if the value changes in accordance with operation. Items to be checked : Each switch (COIN/SER VICE/TEST/START/VIEW CHANGE/HORN/SHIFT<H L R>) Each volume (STEERING WHEEL/ACCELERATOR/ BRAKE)
@ Press the TEST BUTTON and the SERVICE BUTTON simultaneously to return to the menu screen.
Select OUTPUT TEST to cause the following screen to appear, and to check the status of each lamp and motor. In this mode, periodically check each lamp and motor.
OUTPUT TEST
START LAMP. VIEW LAMP. HORN LAMP ROLL LEFT ROLL RIGHT
-> EXIT
AND PRESS TEST BUTTON OFF OFF OFF OFF OFF
SELECT WITH SERVICE BUTTON e Using the SERVICE button, bring the arrow to the desired item and press the TEST button. The display next to the item changes from OFF to ON, and the lamp lights up, or the motor functions.
LAMP item _ : If the lamp lights up, operation is satisfactory. ROLL LEFT _ : If the motor moves so as to turn the steering wheel counterclockwise, operation is satisfactory. ROLL RIGHT :: If the motor moves so as to turn the steering wheel clockwise, operation is satisfactory.
@ Bring the arrow to EXIT and press the TEST BUTTON to return to the menu screen.
C. SOUND TEST
Selecting the SOUND TEST displays the following screen on the monitor. This test mode allows each sound used in the game to be checked.
@ Press the SERVICE button to move the arrow and select an item. SOUND TEST ; , : i Every time the TEST button is pressed, a different sound is played. B.G.M. O/ xx EFFECT O/ xx B.G.M. : Sounds used in the game can be played. Ics __] O/ xx EFFECT : Sound effects used in the game can be played. ] ICS : Sound effects in a loop used in the game can be played -> EXIT e Bring the arrow to EXIT and press the TEST button to return to the MENU screen.
SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT
D. GAME ASSIGNMENTS
Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and allows game setting changes (game difficulty, etc.) to be made. After setting changes, be sure to exit from the TEST mode; the settings are not renewed until the TEST mode is exited.
@ START TIME : The time limit given to the player at the GAME ASSIGNMENTS beginning of the stage can be set. Select from VERY EASY, EASY, NORMAL,
START TIME [VERY EASY]
CHECK POINT TIME [VERY EASY] HARD, and VERY HARD. MOTOR POWER [LIGHT] @ CHECK POINT TIME: The additional time given to the player DEFAULT SETTING when passing the CHECK POINT can -> EXIT be set.
@ MOTOR POWER : The feedback stiffness of the steering SELECT WITH SERVICE BUTTON wheel can be selected from LIGHT, PRESS TEST BUTTON TO EXIT NORMAL, and HEAVY.
@ DEFAULT SETTING : This makes each setting return to its default setting.
Bring the arrow to EXIT and press the TEST button to return to the MENU screen.
E. VOLUME SETTING
Selecting the VOLUME SETTING displays the following screen on the monitor. The volume of the detection for the steering wheel operation can be manually set. The value will be stored upon exiting from the item.
VOLUME SETTING
HANDLE SETTING SET CENTER [LOCK] OOH
->EXIT
SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT
SETTING THE STEERING WHEEL VOLUME
@ Press the SERVICE button to bring the arrow to SET CENTER.
@ “SET CENTER [LOCK]” display changes to “SET CENTER [SET].”
@ _ Manually bring the steering wheel to the centering position.
@ _ Press the TEST buton. The Volume value obtained at this time is stored as the steering wheel’s centering value, and “SET CENTER [LOCK]’is displayed. If the value does not fall within 80+/- 5H at this time, perform volume adjustment by referring to 7-3E (above).
Bring the arrow to EXIT and press the TEST button to return to the MENU screen.
F. BOOKKEEPING
Selecting BOOKKEEPING in the MENU mode displays the data of the present operating status on 2 pages. Press the TEST button to proceed to the next screen. Pressing the TEST button while the second page is showing returns the screen to the MENU mode.
BOOKKEEPING 1/2 NUMBER OF GAMES. oO NUMBER OF CONTI NUE 0 AVERAGE PLAY TIME oOmMOoOoS
PRESS TEST BUTTON TO CONTI NUE
| @ | NUMBER OF GAMES | : Total number of plays. |
| @ | NUMBER OF CONTINUE | : Total number of continues. |
| @ | AVERAGE PLAY TIME | : Refers to the average game play time. |
BOOKKEEPING 2/2 TIME HISTOGRAM
OOMOOS - OOM29S - 0OM30S - OOMS59S - 01MOOS - 01M29S - 01M30S - 01M59S - O2MOOS - 02M29S - 02M30S - 02M59S - 03MOOS - 03M29S - 03M30S - 03M59S - O4MOOS - 04M29S - 04M30S - 04M59S - OSMOOS - O5M29S - 05M30S - O5M59S - O6MOOS - 06M29S - 06M30S - O6M59S - OVER 07MOOS ecoocccccecc0000
PRESS TEST BUTTON TO EXIT
@ In Page 2/2, Histogram of Number of Play as against Play Time is displayed.
@ By-playtime play frequency bookkeeping is displayed in increments of 30 seconds from 00MO0S to 06MS59S. Playtime in excess of 7 minutes is displayed all in the category of OVER 07MO0S.
G. BACKUP DATA CLEAR
Selecting the BACKUP DATA CLEAR displays the following screen on the monitor. In the GAME TEST MODE, this allows the contents of BOOKKEEPING and Player Ranking data to be cleared. The COIN/CREDIT related data can be cleared in the BACKUP DATA CLEAR in the SYSTEM TEST MODE.
BACKUP DATA CLEAR
YES (CLEAR) -> NO (CANCEL)
SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT
@ When clearing, use the SERVICE BUTTON to bring the arrow to “YES (CLEAR)” and press the TEST BUTTON.
@ “YES (CLEAR) COMPLETED” will be displayed, and “COMPLETED” will be flashing. When the data has been cleared, the display will stop flashing. After the data has been cleared, bring the arrow to “NO (CANCEL)” and press the TEST BUTTON to return the screen to MENU mode.
@ Note that despite the “clear” execution, the settingsof the GAME ASSIGNMENTS and VOLUME SETTINGS do not change.
- HANDLE MECHA
eo)
When putting on the HANDLE MECHA, do not put the gear or the sensor portion face down. Failure to observe this may damage the parts due the weight of the mechanism.
Be sure to perform the Volume value setting under Volume Setting in the Test Mode after replacing or adjusting the Volume.
8 - 1 REMOVING THE CONTROL MECHANISM
If the Steering operability is poor and the adjustment of VOLUME SETTING in the TEST mode is ineffective, the cause may be failure of the Volume Gear’s mesh and/or Volume malfunctioning, By using the following procedure, adjust the Volume gear mesh, or replace the Volume. In this product, when the Steering Wheel is moved all the way to the left/right, and the Volume shaft rotates within the movable range, then the Volume is probably not damaged. When securing the Volume, be sure the Volume shaft is oriented as shown and the gears are appropriately engaged when the steerig wheel is in the center position, allowing the truck to go straight forward.
In order to replace or adjust the V.R., remove the HANDLE MECHA as per the following procedure.
©® 2©0LGO CO
® STEERING HANDLE Turn the power off.
Take out the 4 truss screws at the center of the steering wheel to remove the FRAME HORN BUTTON, CUSHION U and the CAP HORN BUTTON. A small part (called the PIN HORN BUTTON) is attached to the CAP HORN BUTTON. Be sure to keep it.
Pull out the ROD HORN BUTTON.
Remove the SPRING and the CUSHION L.
Take out the hexagon nut.
Remove the WASHER HANDLE SHAFT.
Pull the STEERING HANDLE out of the HANDLE SHAFT. The HANDLE and the SHAFT are a nesting of the gear-shaped spline holes and the shaft. Be sure to pull the STEERING HANDLE vertically so as not to damage the shaft.
Remove the COLLAR from the HANDLE SHAFT.
FRAME HORN BUTTON
PIN HORN BUTTON TRUSS SCREW (4)
M4 X25, chrome
SPRING
CUSHION U
CUSHION L
= —— CAP HORN BUTTON
WASHER HANDLE SHAFT
ROD HORN BUTTON
HEXAGON NUT (1) MI6
COLLAR STEERING HUB
COLLAR HANDLE SHAFT.
Remove the 4 Tamperproof screws, and the 4 Phillips screws (8 total) on the angled metal plate located in front of and below the control panel. Remove the panel.
Take out the 8 pape TOO screws to remove the CONTROL PANEL . Use care so as not to damage the wiring inside the CONTROL PANEL COVER. .
@ Disconnect the 2 connectors inside the CONTROL PANEL, and remove the CONTROL PANEL.
(o) Disconnect the HANDLE MECHA’s wire connectors (to the Horn and Start Button)
® Remove the HANDLE MECHA. Use CAUTION when performing this task. @ When setting down the HANDLE MECHA, be sure to have the gear and sensor portions face up. Failure to do so may damage the parts due to the weight of the mechanism.
(may not appear as shown)
8-2 VOLUME ADJUSTMENT/REPLACEMENT
@ Never touch places other than those specified. Touching unspecified places can cause electric shock and/or short circuit. @ After the replacement or adjustment of the VR, be sure to set the variable value of !
Volume adjustment/replacement should be performed after the HANDLE MECHA has been removed as per 8 - 1.
ADJUSTMENT
In order to turn the HANDLE SHAFT, insert the STEERING HANDLE into the HANDLE SHAFT.
Secure the HANDLE at the centering position.
Loosen the 2 screws which secure the VOLUME BRACKET to push the gear out of mesh.
With the HANDLE SHAFT at the centering position, bring the gear into mesh so that the position of the volume’s shaft is as shown in the Fig.
Fasten the screws securing the VOLUME BRACKET. ©G ®©O800O
After the work is finished, perform Volume Setting in the Test mode.
“D” CUT FACE (HANDLE SHAFT)
“D” CUT FACE (VOLUME)
REPLACEMENT
Disconnect the wiring connector.
Take out the 2 screws which secure the VOLUME BRACKET to remove the BRACKET together with the Volume.
Take out the 2 screws, remove the Volume Gear, and replace the Volume.
With the HANDLE SHAFT at the centering position, bring the gear into mesh so that the position of the volume’s shaft is as shown in the Fig.
Fasten the screws securing the VOLUME BRACKET. O©®@ ©0© 080
After the work is finished, perform Volume Setting in the TEST mode.
MAY NOT APPEAR AS SHOWN
- SHIFT LEVER
@ In order to prevent electric shock and short circuit, be sure to turn off the power before performing work on the interior parts of the product.
Tf the Shift Lever operation is not satisfactory, remove the Shift Lever according to the following procedure and replace the microswithch.
9-1 REMOVING THE SHIFT LEVER
® By following “8-1 REMOVING THE HANDLE MECHA”, turn the power off, remove the STEERING HANDLE, and remove the CONTROL PANEL COVER.
@ Take out the 4 Hexagon Bolts.
® Pull up the SHIFT LEVER slowly until the 2 wiring connectors can be seen.
® Disconnect the 2 connectors.
9-2 SWITCH REPLACEMENT
Each Microswitch is secured with 2 screws. Remove the 2 screws and replace he Microswitch.
SCREW_(2) M2.3X12,
flat & spring washers
After replacing the Switch, check its status in the Test Mode.
- ACCELERATOR & BRAKE
@ Be sure to turn power off before performing work, and avoid touching
undesignated places. Failure to do so can result in electric shock and short circuit accidents. @ Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. @ When performing work such as parts replacement other than those specified in this manual, be sure to contact the company the product was purchased from and confirm the work procedures and find out any precautions prior to performing the work. Inappropriate parts replacement and/or installing with improper adjustment can cause an overload or the parts to come into contact, resulting in electric shock, short circuit, or fire.
Gro¥) After having performed the adjustment or replacement of the volume, be sure to check the variation of the volume value under INPUT TEST in the test mode.
If Accel and Brake operation is not satisfactory, adjustment of Volume installation position or Volume replacement is needed. Also, be sure to apply greasing to the gear mesh portion once every 3 months.
10 - 1 REMOVING THE ACCELERATOR AND THE BRAKE
A socket wrench for M6 Hexagon bolts and an extension tool are necessary to remove the accelerator and the brake, in order to perform maintenance. When removing, be careful not to damage wiring or wiring connector inside the accelerator and the brake.
©) Turn power off.
@ Apply the extension tool to the socket wrench. Remove the 4 Hexagon bolts which secure the accelerator and the brake.
6) The two wire connectors are
connected to the accelerator and the brake. Disconnect the connectors, and the accelerator and the brake can be removed. Since this work is performed inside the energized cabinet, be very careful not to touch undesignated parts.
10 - 2 ADJUSTING OR REPLACING THE VOLUME
‘When released: ‘When stepped on: Under 30 H Over COH Under 30 H Over COH
Check Volume values in the Test Mode.
Since work is performed inside the energized cabinet, be very careful not to touch undesignated portions. Touching places not specified can cause electric shock or short circuit.
ADJUSTMENT
® Take out the 2 truss screws and remove the Front Cover from the Accel. & Brake unit.
@ Loosen the screw which secures the Potentiobase, and adjust the Volume Value by moving the Base.
WaxX8, chrom
- Secure the Potentiobase.
® In the INPUT TEST screen, check to see if the volume value varies in accordance with operation of the pedal.
FRONT COVER SCRE Mi X72, w#/flat washer
POTENTIOBASE VR. 220-3373, 5484
REPLACEMENT
oe © © © © CO Be sure to turn the power off first, before performing work, and avoid touching unspecified places. Failure to do so can cause electric shock and/or short circuit.
Turn power off.
Take out the 2 truss screws and remove the Potentiocover.
Disconnect the connector of the volume to be replaced.
Remove the screw which secures the Potentio
Remove the Potentiobase together with the volume attached.
Remove the base and the gear to replace the volume.
After replacing, check to see if the volume value varies in accordance with operation of the pedal.
10 - 3 GREASING
damage
or quality deterioration of parts. @ Be sure to use the designated grease. Using undesignated grease can cause parts
@ Do not apply greasing to undesignated places. Doing so can cause malfunctioning
Apply greasing to the following portions once every three (3) months. For Spray Grease, use NOK GLUBER L60 or GREASE MATE
(Part No. 090-0066).
11 .COIN SELECTOR
HANDLING THE COIN JAM
to see that the selector correctly functions.
CLEANING THE COIN SELECTOR
The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: @ Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). ® Remove and cleen smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. @) Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. © Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. © After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely. ©
@ Never apply machine oil, etc. to the coin selector @ After cleaning the Coin Selector,
IMPORTANT! Insert a regular coin during the
normal working status and ensure that the Selector functions correctly. Insert a coin
COIN INSERTION TEST ene
Once a month, when performing the COIN SW Button pressed
TEST, simultaneously check the following: down and check if itis a : . rejected. O Does the Coin Meter count satisfactorily? J O Does the coin drop into the Cashbox correctly? COIN METER 01 Is the coin rejected when inserted while keeping the REJECT BUTTON is pressed down? If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check
FIG. lla
FIG.11b
FIG. llc
OPTIONAL DOLLAR BILL ACCEPTOR
@ THE COIN DOOR ASSEMBLY USED ON 18 WHEELER STD TYPE COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.
@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING
VALIDATOR(S):
FORWARD-MOST Mars 2000 series HOLE POSITION
**42-1155-00 | MARS VALIDATOR $1, 2,5 300 CAP
The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the cut-out plate. This one entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors. The part number is 40-6000-10EX. The Mars stacker can be obtained through an autherized Mars distibutor.
**Happ part number
""40-6000-1 0EX TEM NO|] ar ean NO. DESCRIPTION 1] 1f42-8174-10 [FRAME O/U DWNSTCK VAL ON LW DA 1[42-8178-00 [DOOR SMALL O/U_F/DWN SICK VAL 1[42-7201-00 [DOOR SMALL 2 ENTRY W/PEM STUD. 42-8176-00_|COINBOX ENCLOSURE O/U OR W/DWNSTCK VAL 1[42-8177-00 |COINBOX METAL O/U DR W/VAL ON LW DR
2[42-7355-00_[MECH HOLDER. 142-3079-00 [COIN MECH ULTIMECH 1[42-7486-00 _|COIN MECH FOR 28MM/1.10 TOKEN 3] 2142-7087-00_|switCH ASSEMBLY 2/42-3286-00 [SWITCH PLATE -4[43-0136-00 |sCREW #4 x 3/16 12] 2[42-0641-100 |LOCK ASSEMBLY 13] 2/42-0231-00 entry BezeL 1|42-0695-05 $1.00 REJECT BUTION ASY.,, YELLOW 1[42-1044-00 [REJECT BUTTON, HAPP. 142-0405-04 [COIN RESIRICTOR, 27MM 1142-0405-00 [COIN ENTRY RESTRICIOR. 2{42-0119-00 RETURN DOOR FLAP. 2142-0232-00 RETURN BEZEL 4143-1003-00 _|SCREW. PLASTIC 44X42 21] 6[43-1002-00 WASHER, FLAT #6 za 12[48-1000-00_ SCREW FOR BEZEL
al 2] 2| 42-0288-00 [DOOR CLIP [43-0047-00 SCREW, MS X 10MM HEX WASHER HD. [91-1319-00_|LAMP_#555 6.3. [42-0351-00_|LAMP HOLDER [42-0065-00_|SCREW BX 1/4 142-0063-00_|KEY HOOK [42-0526-00 [BLANKING PLATE 143-0021-00_| CARRIAGE BOLT 832 x 1/2 [42-0082-00_[NUT. KEPS 6-32
a * * Eo] vo i] oO & i=] i) g s zy re) > z a a} x) a c a] a eo = g iS s a é =| 1S) * *
- MONITOR
12 - 1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS
When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor, be sure to disconnect the power connector (plug) before starting work. Proceeding the work without following this instruction can cause electric shock of malfunctioning.
Primary side and secondary side The monitor’s circuit which is divided into the Primary side and secondary side, is electrically isolated. Do not touch the primary side and the secondary side simultaneously. Failing to observe the instruction can cause electric shock, and this is very dangerous. SECONDARY SIDE When making monitor adjustments, use a non- (Chassis, CRT) conductive driver and make adjustment without touching any other part other than the Adjustment PRIMARY V.R. and Knob. Also, be sure not to cause a short- SIDE circuit to the Primary side and the Secondary side. If short-circuited, it can cause electric shock or mal-
functioning, which is very dangerous. @
High tension Voltage Some of the parts inside the monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor, turn the power off so as not to cause malfunctioning or fire hazard.
2) ANODE CAP PRIMARY SIDE DEMAGNETIZER REAR PART
ANODE LEAD ‘Approx. 29 kV
DEMAGNETIZER COIL
SECONDARY SIDE i FBT Approx. (Chassis, sheet metal work, CRT, etc.) Disconnect or unplug 29kV
Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulitavely charged as time elapses, generating high tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as assembled” condition. If these are disassembled, what’s charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.
Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the CRT surfaces are subject to static and will not adversly affect the human body. Installation and removal t Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are
For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the
CAUTION! coating, pay attention to the following
points. Damaging the coating film can cause electric shock to the customers. For the caution to be heeded when . . clearing, refer to the Section of Periodic Aluminum Foil inspection Table. Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on C.R.T. surfaces. Avoid applying stickers, seals, etc. on the C.R.T. face. Do not remove aluminum foils from the C.R.T. corners. Removing the aluminum foils can cause static prevention effects to be lowered.
Monitor adjustments have been made at the time of shipment. Therefore do not make further adjustment without a justifiable reason.
12 -2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES
Static preventive coating is applied to the CRT surfaces. Peeling off this coating can cause electric shock. When cleaning, pay attention to
CAUTION! the following points:
Remove smears by using a dry, soft cloth (flannels, etc.). Do not use a Coarse gauze, etc. For smear removing solvent, alcohol (ethanol) is recommended. When using chemical detergent, e sure to folow instructions below: Dilute chemical detergent with water and dip a soft cloth in and then thoroughly wring it to wipe smears off. Do not use a chemical detergent containing an abrasive, powder or bleaching agent. Do not use alkaline chemical detergents such as “glass cleaner” available on the market or solvents such as thinner, etc. Do not rub or scratch the CRT face with hard items such as scrub brushes, etc.
Clean the CRT surfaces once a week. When cleaning, pay attention to the above cautions so that the antistatic coating will not come off.
12 - 3 ADJUSTMENT METHOD
NANAO monitor: 200—5242—24—0 4 (24K mode)
SANWA monitor: 200-5 2 4 3-2 4 (24K mode)
HGhobdes
G®S © ®G®OOD OO WO [ Roa GGAIN BGAIN BRIGHT HSIZE HHOLD HPOS! SIZE VHOLD POS @ ran ® G-GAIN ores Controls colors. @ B-GAIN
- BRIGHT .......... Controls screen brightness. ©) wsue... © Hop. @ 4. post... Controls horizontal screen size. Provides horizontal synchronization, i.e., controls right/left hold. Controls horizontal display position on screen. Controls vertical screen size. Provides vertical synchronization, i.e., controls up-down hold, Controls vertical display position on screen. @ CONTRAST.... Adjusts image contrast.
- REPLACING THE FLUORESCENT LAMP AND BUTTONS
@ When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. @ The Fluorescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.
To perform work safely and securely, be sure to use a step which is in a secure and stable condition. Not using a step or using an unstable step can cause violent falling accidents.
THE FLUORESCENT LAMP
® Take out the 2 Truss Screws and remove the Plate Holder.
@ Lower the Billboard Plate and replace the Fluorescent Lamp. | LAMP COVER A FLATHEAD SCREW (2) _// M4X8, black
FLUORESCENT LAMP 20¥: LOCAL PURCHASE
START BUTTON AND VIEW CHANGE BUTTON
Use care so as not to damage the wiring connection inside the start button and the view change button.
Turn power off.
Take out the 4 truss screws. © EO
Disconnect the connector attached to the start button and view change button, and the VR BUTTON START AND VIEW | can be removed.
@® The lamp is on the PCB side. Turn the metallic parts of the 2 buttons, unlock and remove the PCB from the buttons.
- With the lamp pressed down, turn it counterclockwise to remove.
- PERIODIC INSPECTION TABLE
The items listed below require periodic checks and maintenance in order to retain the performance of this machine and ensure safe operation.
@ Be sure to check once a year to see if Power Cords are damaged, the Plug is securley inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product when dust has accumulated can cause a fire or
Interval Check Adjusters’ contact with surface. Daily
| HANDLE MECHA | Check Lamp. | Monthly |
Check VOLUME VALUE. Monthly Check ADJUST GEAR engagement. Trimonthly Greasing of GEAR. Trimonthly
| ACCEL. & BRAKE | Check VOLUME value. | Monthly |
Check ADJUST GEAR engagement. Trimonthly Gear and Spring portion greasing. | Trimonthly
| ‘SHIFT LEVER | Check ewitches, | Monthly |
| COIN CHUTE TOWER | Check COIN SH. | Monthly |
Coin insertion test. Monthly Cleaning of COIN SELECTOR. Trimonthly
| MONTTOR | Check adjustments. | Monthly or shen moving. |
Cleaning of CRT surfaces. Weekly
SEAT Antistatic measures Bimonthly
| CAME BD | MEMORY TEST. | Yenthly |
Check settings. Monthly
| Cabinet surfaces | Cleaning | As occasion arises. |
INTERIOR Cleaning Annually
POWER SUPPLY PLUG Inspection and cleaning
CLEANING CABINET SURFACES
If the cabinet is badly stained, use a cloth which is dipped in the chemical detergent liquid diluted with water and then squezzed dry. Do not use thinner, benzine, alcohol or chemical dustcloths, as these can damage the Cabinet surfaces.
- TROUBLESHOOTING
Should trouble occur, first check connector connections.
PROBLEMS CAUSE COUNTERMEASURES
With Main SW ON, no activation Power is not supplied.
Power supply/voltage is not correct.
AC main fuse causes the power to be cut off due to momentary overload. Plug in correctly
Make sure that power supply/voltage is correct. Check fuse. Remove the cause of overload and replace fuse
Operation is unsatisfactory Volume Setting Failure
Poor mesh of V.R. gear.
Spring failure due to secular change of Accelerator and Brake Mecha. Perform Volume setting Adjust or replace V.R.
Adjust Gear mesh..
Replace the Spring.
Irregular sound emitted from inside Rear Cabinet Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Apply greasing or eliminate extraneous matter.
No sound is emitted. Sound Volume adjustment is not appropriate.
Sound BD and speaker are malfunctioning. Adjust sound volume. (see Chapter 7-1).
Perform sound test to find and replace defective parts.(Refer to Chapter 7-3E).
No sound from Cockpit. In correct Cabinet Type Setting. Correct Cabinet Type Setting.
The Fluorescent lamp does not light up.
Shift lever does not operate satisfactorily. The Fluorescent tube is burnt out.
Shift SW malfunctioning. Replace the Fluorescent tube (Refer to Section 11).
Replace SW
Operation of Accel. and Brake Pedals are not satisfactory. VR. malfunctioning.
Adjust Gear not engaged properly. Replace the V.R.
Adjust the engagement of the Adust Gear.
- GAME BOARD
@ In order to prevent an electrical shock, be sure to turn power off before performing work. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.
In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. with the same settings made at the time of shipment. Do not expose the Game BD, etc.
16-1 LOCATING THE GAME BOARD
® Turn power off.
@ Take out a total of 6 Truss Screws and unlock to remove the Seat.
(6) The GAME BOARD is located at the
position shown in the photo below.
Use two or more persons when performing work.
16 -2 COMPOSITION OF GAME BOARD
Be sure to use the specified settings for the DIP SWes on the Filter Board. Failure to do so may cause irregularities or malfunctioning, such as unsatisfactory images displayed on the screen.
ASSY CASE NAO PTR USA (840-00023D-01)
NN 849-O001A-01 ASSY CASE NAOME MAIN 2D USA
DIP SW SETTING
In this product, be sure to set all of the DIP SWes to OFF.
- DESIGN RELATED PARTS
ITEM NO. PART NO. DESCRIPTION
| 1 | 999-0916 | MARQUEE PLEXI (MACHINED) |
| 2 | 999-0915 | OVERLAY - CONTROL PANEL |
| 3 | 999-0910 | DECAL - MAIN CAB L |
| 4 | 999-0911 | DECAL - MAIN CABR |
| 5 | 999-0912 | DECAL - SEAT OUTSIDE L (INCL. EXHAUST) |
| 6 | 999-0913 | DECAL - SEAT OUTSIDE R (INCL. EXHAUST) |
| 7 | 999-0914 | DECAL - SEAT BACK |
- PARTS LIST TOP ASSEMBLY PTR
» Ka ASSY HILLBOARD 998.09 ASSY SHIFTER 3b277)
ER swosiany 2200
DO AUTO MS-2551 5 N24 ASSY ACCEL ANDBRARE — SttGe
ASSY STEDIUING
ASSY BILLBOARD (999-0922)
4y(5)(6 in?
O_, ot O= _
ITEM NO. PART NO. DESCRIPTION
| 1 | 999-0916 | MARQUEE PLEX |
| 2 | Local Purchase | ASSY FL FIXTURE |
| 3 | 999-0925 | LENS COVER RED |
| 4 | 999-0926 | LENS COVER YELLOW |
| 5 | Local Purchase | 14 V LIGHT BULB (#293 IMPERIAL) |
| 6 | 999-0928 | 14 V SOCKET FOR BULB |
| 7 | 999-0927 | LIGHT STRIP PLATE |
| 101 | Local Purchase | ASSY FL 15W W/CONN HIGH L |
| 202 | Local Purchase | 8 X 32 MACHINE SCREW |
ASSY STEERING UNIT PRUE ISSI SESE Sy at ' ‘ i assy 9
| FIR-E% | \ | Ses Drang | \ | **100-5357 |
| im | { | 19 Vesta Back | Bewnz8 | |
| PIRSB | ‘ | for detail of thas wea | ! | 990.0948 |
Cole A Eine Beier, Bearng ode ; 990-0989 Serpe Be me Screw Ste Hax 103234" boat Hirdered +M0SpRt Lode VRster Bi basi
cake me *Sceae Phillips 46-32:309"
Vasher, Bearing Large 908.0955 y ee
i
IRIE Steering Vel 9op.Ho81 Nz 39-11 Nyle
99S ‘Spring Hom 993.0937 Eom Button
998-0980 Screw L4-201 34" ‘Temper Prod Tom {+ we TK va
Purdhase ** inched Aconhy Rer &
MODIFICATIONS TO PARTS ASSY #PTR-1000 (ASSY CHANGED TO PTR1-1000)
PART NOT LIS ED OR SHOWN IN DRAWING #999-0903 (3) Steering Spoke Cover Upper PART NOT LIS ED OR SHOWN IN DRAWING #999-0904 (3) Steering Spoke Cover Lower Attached to Item #32 (Part No. PTR-2501 STEERING HANDLE) These parts are used for extra support/safety and are included in all US manufactured games.
Location of Spoke Covers
Steering Handle
ASSY AC UNIT (DRT1-0400)
ITEM NO. PART NO. SPG5-0401 600-5843-25 280-5143-6N34 Local Purchase 509-5453-91-V-B (ry 02)
DESCRIPTION AC BRKT CA & PLUG ASSY 15A W/F-L=2.5M BUSHING STRAIN RELIEF 6N34 FUSE 5000 MA UL SW ROCKER J8 V-B
ASSY COIN CHUTE TOWER = (999-0923)
ASSY COIN CHUTE TOWER = (999-0923)
ITEM NO. PART NO.
1 INY-1180 2 PTR-1201 3 APC-0301 4 APC-0302 5 DRT-0301X 6 DP-1167 7 105-5171 8 253-5366 9 421-7501-02 10 440-WS0002XEG 11 421-6591-01
101 40-6000-10EX 102 220-5643-01 103 220-5574 107 310-5029-F20 108 601-6231-C045 109 220-5575
201 000-P00408-W 202 000-P00408-S 203 060-F00400 204 050-H00800 205 068-852216 206 060-S00800 DESCRIPTION
SW UNIT TOWER COVER L COINCHUTE TOWER METER HOLE LID COIN METER BRKT TNG LKG CHUTE PLATE SINGLE CASH BOX STICKER 6.3V 0.15A STICKER W POWER OFF ENG STICKER COIN METER
ASSY C.C 2DR *SEE IMAGE NEXT PAGE MAG CNTR DCSV 6P WH MZ-674-D04 CAM LOCK W/KEYS SUMITUBE F F 20MM EDGING NEW TYPE CAM LOCK MASTER W/O KEY
M SCR PG W/FS M4 X 8 M SCR PG W/S M4 X 8 FLT WSHR M4 HEX NUT M8 FLT WSRR 8.5-22 X 1.6 SPR WSHR M8
- SEE IMAGE OF COIN DOOR ASSY ON THE FOLLOWING PAGE,
"40-6000-1 EX d Ey [42-8 174-10 [FRAME O/U OWNSTCK VAL ON LWDR [42-8 178-00 |DOOR SMALL O/U F/DWN SICK VAL [42-7201-00 [DOOR SMALL 2 ENTRY W/PEM STUD. 42-8176-00_|COINBOX ENCLOSURE O/U OR W/DWNSICK VAL [42-8177-00_|COINBOX METAL O/U DR W/VAL ON LW DR 42-7355-00_|MECH HOLDER. 42-3079-00_|COIN MECH ULTIMECH, |42-7.466-00_|COIN MECH FOR 28MM/1.1OTOKEN /42-7087-00_|SWIICH ASSEMBLY l42-3286-00 [SWITCH PLATE [43-013600 [SCREW #4x 3/16 [42-0641-100 LOCK ASSEMBLY 142-0231-00_lENTRY BEZEL [$1.00 REJECT BUTION ASY, YELLOW. REJECT BUTTON, HAPP.
i oe ear) 142-0405-04 [COIN RESTRICTOR, 27MM [42-0405.00 COIN ENTRY RESTRICTOR [42-0119-00 RETURN DOOR FLAP. [42-0232-00 RETURN BEIEL [43-1003-00 _|SCREW. PLASTIC 44x .42 [43-1002-00_|WASHER, FLAT #6, [48-1000-00_ISCREW FOR BEZEL lboor Cur [43-0047-00- ISCREW. M3 X 10MM HEX WASHER HO 191-1319-00_|LAMP_#555 6.3 147-0351-00_|LAMP HOLDER [42-0045-00 8X14 [42-0063-00_[KEY HOOK [42-0526-00 [BLANKING PLATE /43-0021-00 [CARRIAGE BOLT 832 x 1/2 /42-0082-00_[NUT. KEPS 8-32 S| =PHPe Te] Ol ee 2] cof AP PT
ASSY SWITCH UNIT (INY-1180)
ITEM NO.
104, PART NO.
INY-1181 421-8911
220-5179 509-5028 601-0042 310-5029-D20 DESCRIPTION
SW BRKT STICKER SW UNIT
VOL CONT B-5K OHM SW PB IM KNOB 22 MM SUMITUBE F D 20 MM
ASSY HI/LOW/BACK SHIFTER (50-2771-00EX)
ASSY HI/LOW/BACK SHIFTER = (50-2771-00EX)
ITEM NO. i. CIDKARwWH a}
IS PART NO. 96-0094-00 96-0095-00 96-0084-00 96-0092-00 50-8390-00 50-8418-00 50-8346-00 96-0090-00 50-8299-00 96-0089-00 95-4118-00 43-0133-00 43-0118-00 50-8413-00 50-8422-00 50-8406-00 50-8491-00 43-1016-00 43-0252-00 43-0134-00 50-8118-00 50-8294-00 96-0088-52 43-0001-00 43-0417-00 43-0755-00 DESCRIPTION BASE PLATE 4 SPD SHFT BLK SIDE BRACKET W/PIN CLR ZNC PLT GATE BLOCK UPPER MOLDED SIDE BRACKET NO PIN CLR ZNC PLT INNER BOX A, SUB ASSY, PLT INNER BOX B, ASSY TRUNNION FOR LL. TURBO SHIFTER KNOB & SHAFT ASSY 1-3/4 BLK BALL KNOB ANCHOR PIN, HANDLE BLK OXD. ACTUATOR, SPRING STEEL (QTY.3) MS. DA3 90 GRMS. F. (QTY. 3) #145 BRS FLAT WSH .26X.56X.04 (QTY. 6) E-RING, 1/4" SHAFT DIA (QTY. 4) TOP PLATE, BLACK NO ART GUIDE WASHER, 4 SPD SHIFTER BUSHING, NYLINER, F/.078 THK MAT. (QTY. 2) BUSHING, NYLINER, F/.072/.135 THK MAT. (QTY. 2) SCREW, 8-32 X 1/2 PHMS (QTY. 4) SCREW, 8-32 X 3/8 HEX HEAD (QTY. 8) SCREW, 8-32 X 5/16" PH HD MS W/SEMS E-WISH (QTY. 2) E-RING FOR GEAR SHIFTER M15 SPRING, HAIRPIN, HLR SHFTR, SHORT (QTY. 2) LOWER GATE BLOCK W/INSERTS SCREW, 2-56 X 1/2 PPMS (QTY. 6) SCREW, 2-56 X 5/8 PPMS (QTY. 3) NUT, 2-56 NYLOCK (QTY. 3)
(Q0@Z-DdS) AMVUAG GNV THOOV ASSV
ASSY ACCEL AND BRAKE = (SPG-2200)
ITEM NO. PART NO. DESCRIPTION
| 1 | SPG-2201 | BASE |
| 2 | SPG-2202 | ACCEL PEDAL |
| 3 | SPG-2203 | BRAKE PEDAL |
| 4 | SPG-2204 | ACCEL SPRING |
| 5. | SPG-2205 | BRAKE SPRING |
| 6 | SPG-2206 | SHAFT |
| 7 | SPG-2207 | ACCEL GEAR |
| 8 | SPG-2208 | BRAKE GEAR |
| 9 | SPG-2209 | NEUTRAL STOPPER |
| 10 | SPG-2210 | VR PLATE ACCEL |
| 11 | SPG-2211 | VR PLATE BRAKE |
| 12 | SPG-2212 | AMPL GEAR |
| 13 | SPG-2213 | GEAR SHAFT |
| 14 | SPG-2214 | STOPPER |
| 15 | SPG-2215 | RUBBER CUSHION |
| 16 | SPG-2216 | COVER |
| 17 | SPG-2217 | VR COVER |
| 19 | SPG-2219 | GEAR STAY |
| 20 | SPG-2220 | WSHER |
| 21 | SPG-2221 | NEUTRAL STOPPER D |
| 101 | 100-5263 | BEARING 12 |
| 102 | 220-5484 | VOL CONT B-5K OHM |
| 104 | 601-7944 | GEAR 15 |
| 105 | 310-5029-F15 | SUMITUBE F F 15MM |
| 201 | 028-A00304-P | SET SCR HEX SKT CUP P M3 X 4 |
| 202 | 020-000520-OZ | HEX SKT H CAP SCR BLK M5 X 20 |
| 203 | 000-P00420 | MSCR PH M4 X2 |
| 204 | 000-P00508-W | MSCR PH W/FS M5 X 8 |
| 205 | 000-T00408-0C | M SCR TH CRM M4 X8 |
| 206 | FAS-450005 | SPR PIN BLK OZ 6 X 10 |
| 207 | 000-P00405 | MSCR PH M4 X5 |
| 208 | FAS-000001 | M SCR TH CRM M3 X 6 |
| 209 | 050-H00500 | HEX NUT M5 |
| 210 | 060-F00400 | FLT WSHR M4 |
999-0873 WRB *Sormw Phillipe 10-322" wht Washer 99-0847 Gear, Pa oc *Somw 63222 999-0943 Coupling, PotGeat 999-0R4z SEPot Long Lite Imperial 999-0850 Opto Bd Horn 999-0995 LS "Sand off (2 *Somw Phillipe #4-40c1/2"(2 18 Wheeler Stanclaicl Steering Assembly 999-0059 Stopper Rubee 999-0978 Stopper Bracket *Sorw Phillipe HOS2d/2" wLock Washer (4)
999-046 Gear, Main ShattS0 *SetScrew Hex 6-32cl4"(Q 99-049 Ring Reiner, Bearing *Somw Philips #6-326/8" wLhock Washer (Z) WITh? wu Thiele *Scew Philip 1OSDd/2' wht Washer(Z
See "Detail A" for parte fi identification of Tension Unit
*Scomw Philip 10-Sad/2 *#10Flat Washer IB-OSTE. #10 Shoulder B auiZ =a: 999-04¢ Friction Block- Nylor + LOCAL PURCHASE 999-0876 Tension Bracket
SpringtZ "Detail Av De Davidson 1400 ASSY OF HANDLE MECHA
ASSY SENSOR UNIT (PTR-2550)
ITEM NO. PART NO.
1 PTR-2551 2 PTR-2552
101 370-5226
202 000-P00312-W DESCRIPTION
SENSOR BEKT GUIDE RING
PHOTO SENSOR OMT-01DAMP NEW
M SCR PH WI/FS M3 X 12
ASSY VR BUTTON START AND 1 VIEW (PTR-2600)
ITEM NO.
(BLUE)
PART NO.
APC-2151X 171-6478B PTR-2601
212-5205-12 **54-0006-25 **54-0006-42 DESCRIPTION
VR BUTTON BRKT PC BD LIGHTING SWX5 STICKER VR BUTTON
CONN JST M 12P RTA SM ROUND YELLOW 5V #161 MICRO SQUARE BLUE SV #161 MICRO
**HAPP PART NUMBER
ASSY WOOFER = (999-0929)
ITEM NO. PART NO. DESCRIPTION 101 999-0929 SUB WOOFER 4 OHM 25W
ASSY MAIN BOARD = (PTR-4000)
2-6 30
ITEM NO. PART NO.
PTR-4001 840-0023D-01 837-13844
000-P00416-W 011-T00316 O11-T03512 011-F00312
600-7141-050
DESCRIPTION
MAIN BD BASE ASSY CASE NAO PTR EXP I/O CONTROL BD 2 FOR JVS FRI
M SCR PH W/FS M4 X 16 TAP SCR TH 3 X 16 TAP SCR TH 3.5 X 12 TAP SCR FH 3 X 12
CABLE JVS TYPE A-B 050CM
ASSY AMP BOARD (PTR1-4200)
ITEM NO. PART NO.
1 PTR-4201 2 DRT-4502 3 421-7914-250630
101 601-10369 102 560-5419-V 103 838-13723 104, 260-0011-02 105 601-8543 106 514-5086-6300 107 514-5084 110 400-5397-01 112 310-5029-D20
201 000-P00312-W 202 050-F00300 203 000-P00416-W 204 O11-P00325 205 O11-F00312 206 011-T03512 207 O11-F00312 DESCRIPTION
AMP BD BASE FAN MOTOR BRKT STICKER AC 250V 6.3A
STEREO PWR AMP 47 XFMR 100V 23V 9.6A X 2 WOOFER AMP 50W X 2 AXIAL FLOW FAN AC100V 50-60HZ FAN GUARD FUSE S.B 6.25A 250V HBC CE FUSE HOLDER F-60B W/F-60 SW REGU FOR JVS VA SUMITUBE F D 20 MM
M SCR PH W/FS M3 X 12 FLG NUT M3 M SCR PH WIFS M4 X 16 TAP SCR PH 3 X 25 TAP SCR FH 3 X 12 TAP SCR TH 3.5 X 12 TAP SCR #1 FH 3 X 12
ASSY OF POWER SUPPLY (PTR-4300)
ITEM NO. PART NO.
PTR-4301
PTR-4302
PTR-4303
101 838-11856-UL
106 560-5384
202 011-P00325
203 011-F00310
204 011-T03512
205 000-P00616-W
DESCRIPTION
PWR SPLY BASE
CONN BRKT VL3P
CONN BRKT UP18P
CONNECT BD UL
XFMR 100-200V 100V 10A WB
AC 110 ~ 120V AREA
TAP SCR PH 3 X 25
TAP SCR FH 3 X 10
TAP SCR TH 3.5 X 12
MSCR PH WIFS M6 X 16
EARTH WIRING
ASSY MAIN BILLBOARD
STR-1070 FAN UNIT ra. ©
858-11651-21 LOWPASS AMP W/LARGE HEAT SINK =
SPEAKER A
SPEAKER R. SSPEAKER 1 ajsreaxer ¢ i
ASSY ELEC 12.69 nUKM A
SB acer
acto
MONITOR
840-0023
ASSY CASE NAO PTR
$0e-141-458
10 (0-2/2) POS. C2 ®
erate? STC-165@
FRI-1500/1780
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
VISIT OUR WEBSITE!
ae (Je AGQeeass a nittp:/ Awww seusety ice com /SEGASERVICE /malnpag thst nal sla al Seger iarvce
Coin-Op Links:
Star Tech Journal Amusement Industry Mega Site
‘Sega Enterprises inc, USA if you have any questions about this Home Page please Service Department E-Mail ta: Phone (650)-632-7580 Fax (650) -632-7594 darl.davidson@seu.sega.com best viewed vith imrbesence A total of PROMISE] people have accessed this page.
WE icv Si5i'31 LY2K COMPLIANCE]
SEGA
SEGA ENTERPRISES, INC. (USA)
45133 Industrial Drive Fremont, CA 94538 (650) 632-7580 phone (650) 632-7594. fax